Search Results

Search found 7529 results on 302 pages for 'replace'.

Page 221/302 | < Previous Page | 217 218 219 220 221 222 223 224 225 226 227 228  | Next Page >

• Sending e-mail on behalf of our customer(s), with Postfix

  - by NathanE

  We send e-mail on behalf of our customers, via our own SMTP services. It's always been a problem for us because usually our "spoofing" of their source address results in the mails being caught in spam traps. This hasn't been a problem in the past due to the small volume and low importance of these mails that we sent. However this requirement has recently changed and we need to fix this issue. We realise that fundamentally our application is sending e-mail incorrectly, as per this post: Send email on behalf of clients However, we would like to resolve the problem at the SMTP server level. We have deployed a server running Postfix. Is it possible to have Postfix automatically adjust the mail headers so that we get this "Sent on behalf of" behaviour? I figure it should just be a case of Postfix noticing that the FROM address is the spoofed (i.e. a domain that is not mentioned in its config anywhere) and therefore inject/replace the appropriate headers to get the desired effect. Thanks.

  Read the article

• Transfer disk contents *without* cloning tools

  - by Chris Cummins

  Is it possible to "clone" a disk which contains programs by performing a copy of all the disk contents (preserving file attributes) from source to destination disk, and unplugging the source disk and changing the drive letter of the destination disk to match that of the source? Context I have a two disk Windows 8 system with a system drive and a data drive. Recently, the data drive developed a number of bad sectors leading to IO errors. I have been sent a replacement drive so I simply need to clone the contents of this data drive onto the replacement. The drive contents include documents & media, user folders (My Documents and related), and some programs (games etc). Problem The problem is that the bad sectors on the source disk causes most disk cloning tools to fail with read errors. Attempted approaches include: Disk clone from live boot environment with Acronis True Image. Fails due to read errors. Disk clone from live boot environment with Clonezilla. Fails due to read errors. Disk clone using Roadkil's Unstoppable Copier. Fails due to hardware timeouts in the HDD (application hangs indefinitely). A straightforward copy from source to destination disk using FreeFileSync (preserving file attributes and metadata). This succeeds. So at the moment I have a replacement disk which contains all of the data from the original disk. Now all I need to is somehow get Windows to replace all references to the old disk to the new one. Is this possible by simply swapping the assigned drive letters? Any help would be greatly appreciated, thanks!

  Read the article

• Simple electric DC question. Currency consumption

  - by Bobb

  Suppose you have DC power supply and a consumer connected to it (i.e. computer PSU and a hard drive). Suppose PSU which was supplied with the consumer has output 5V 1A. So I assume that the consumer should not consume more than 1A. Suppose the original PSU is broken now and I want to replace it with the one I have which is 5V 10A. My guess is that current is something which depends on the consumer. So if the consumer consumes normally 1A then it will not consume more than that even if it is connected to 10A PSU. In other word - am I right assuming that the consumer will not burn out being connected to a power supply with higher current output? P.S. my understanding is that voltage is something independent from the consumer. If you give it higher voltage it will burn (voltage is from PSU to the consumer). However current must be in opposite - consumer sucks as much current as it need not as much as PSU can provide (of course given that max PSU current is greater than the consumer needs)

  Read the article

• Replacement for public folder workflow, I'm confused as to how sharepoint does it.

  - by RodH257

  For years Microsoft has been slowly phasing out public folders, perhaps exchange 2010 really is the LAST TIME they'll be shipped... I've heard sharepoint is the replacement, but I don't understand full, can someone give me an idea of how to replace this workflow? In our office, we have projects, they have a project number, ie 10353. Each job folder has a public folder, organized in a hierachy like Projects Year Folder Subfolders The main subfolder we use is for genera correspondence. When an email is received that relates to a project, it is dragged and dropped (or right click move to) a public folder. Adding public folder favourites for each user helps this. When an email is sent, we have a custom email form, which is the default email form, but with a project number field next to the subject line. When you enter the job number in there, it carbon copies our filing system in, which reads the job number and puts the email in the public folder for you. if you need to refer to emails, you go to public folder and find them there. This isn't the best with large jobs, but it works ok. Now, I have limited experience with sharepoint (well, WSS), we've used it to do some neat discussion boards/polls etc as an intranet site, but I haven't seen much of its integration with outlook. The great thing about our solution is how tightly it integrates with outlook which is exactly where the emails are. If you want to forward an old email, you go to public folder and forward it, simple. Any solution that replaces it should be at least as easy as this. Improvements we would like would be to have better searching of emails, better support in exchange (ie future version) and also, custom forms in outlook are being phased out (the VBA kind), so avoiding these would be good. Does sharepoint do this? or what solutions do this kind of thing?

  Read the article

• Having two IP Routes/Gateways of last Resort on an HP Switch

  - by SteadH

  We have an HP Layer 3 Switch that is doing IP routing between vlans. The general set up is that the switch has an IP address on each VLAN and IP routing is enabled. On our servers VLAN, we have a firewall that has a connection to the outside world. To set a IP route on the HP router, we use IOS command ip route 0.0.0.0 0.0.0.0 192.168.2.1 where 192.168.2.1 is the address of our firewall, and the zeros essentially mean to route all traffic that the switch doesn't know what to do with out the firewall as a gateway. We're in the middle of an ISP and firewall change. I set up the new firewall and ran the IOS command ip route 0.0.0.0 0.0.0.0 192.168.2.254 (the address of the new firewall). Things started working nicely. When I reviewed the configuration of the switch though, I noticed that it did not replace the previous ip route command, but just added another route. Now, I know how to remove the old firewall route (no ip route 0.0.0.0 0.0.0.0 192.168.2.1), but what is the effect of having these two 0.0.0.0 routes? Is it switch implosion? Will a server just respond back over the route it receives the request from? I've read elsewhere that having two default gateways is an impossibility by definition, but I'm curious about this situation that our switch allowed. Thanks!

  Read the article

• I need to preserve a tape using symantec backup exec. I'm aving trouble doing so

  - by MrVimes

  Please forgive me if this is the wrong stack exchange site. Please suggest which one I should post this to if it is. There's an automatic tape machine running in a remote location, with software (symantec backup exec 11d) Recently one of the servers being backed up had problems with its raid controller, so one of the drives has become invisible. I need to preserve the last good backup of that drive so I am trying to replace the tape with the most recent backup of that drive on it with one of the scratch tapes (blank tapes) present in the machine. I've tried the following... Associate the blank media with the media set in question (Wednesday) For the existing media (the tape with the data I want to keep) I click 'move to vault' and move it to the offline vault. I associate it with something other than 'Wednesday' (a media set called 'keep data infinitely...') I then do an inventory on that slot. The above steps I'm led to believe are supposed to put the fresh tape in the slot that had the tape I want to keep in it. But it just keeps showing up as containing the tape I want to keep after the inventory. (after refreshing the device tree) I am a complete newbie with this software. Can you tell me what I'm doing wrong, and/or tell me how to acheive my desired goal Edit: Just want to point out that I did try to get help directly from symantec with this, but having jumped through countless hoops to create an account and create a support ticket my progress was halted by requiring something called a 'tecnical contact id' at the final step with no explanation of what it is or how to get one.

  Read the article

• GPO - Setting not applied, although policy is applied

  - by Kenny Bones

  This is rather strange. In our domain we have several terminal servers and this morning a user reported that no drives are mapped when he logs on to the terminal server. So, I checked Group Policy Results and compare two users. Both users have the exact same policies applied. But for this particular user, the Script section under User Configuration - Policies - Windows Settings is just not there. For the other user, which this is working fine for, it says under the Script section that Winning GPO is Terminal2008, which is the GPO that contains the script section. And the Terminal2008 GPO is applied to both users. Also, the loopback processing is set to Replace. What could be the cause for this? I've never seen this particular issue before. I mean, both users are in the same OU, they log on to the same terminal server and the same policies are applied to both. They do not however have the exact same group memberships, but should that matter? It's not stated that the script should be run only if the user is a member of a certain group either. Not sure if that could be done through that specific setting either.All I know is, the very same policies are applied to both users, in the same OU and the same computer. Meaning, the same policies should be applied? Edit: I just ran Group Policy Results on one of the other terminal servers, which are also in the same OU, and the Scripts section is there! This means that this particular user don't get this setting when he's logged onto this particular server. What could be the cause of this?

  Read the article

• Troubleshooting an overheating CPU

  - by Jeff Fry

  I & my father just recently put together a new PC. Specs below. From the very beginning, on boot it will often complain that the CPU is too hot. If I sit in BIOS and watch the CPU, it'll drop back down from red to blue (<72C), at which point I've tended to just boot into Windows...and haven't had any problems. In fact, I've played a couple hours straight of Skyrim at max settings, and not had any visible issues. That said, I've occasionally walked away & come back to find that it's crashed. Yesterday, it crashed (while idle) twice in 12 hours, which shifted the balance from busy-with-life to nervous-I'm-about-to-melt-something. I just installed Core Temp which is showing my 4 cores fluxuating between 70-98C. I'm guessing at this point that the CPU fan may be incorrectly installed or defective. My first thought is to either (a) add water cooling (which the case supports) and / or (b) replace the CPU fan with an after-market one. That said, I'm very open to suggestions. A note, while I certainly don't want to burn money here, I have a baby coming any day now and am still unpacking from a recent move so if I have a choice between an option that costs money and another that takes a while...I'll happily spend a bit extra. Side question: Should I be nervous to even have this on at this point? Let me know if there's something useful I could add to my report. Otherwise, I'm looking forward to your suggestions! Thanks. CPU Intel i7-2600 CPU w/ stock fan Other HW ASUS P8Z68-V Pro motherboard 64G SSD boot drive 4 older SATA HDs GIGABYTE ATI Radeon HD6950 1 GB DDR5 8G Kingston T1 Series RAM Corsair 650W Gold Certified power supply Antec P280 case

  Read the article

• Replacing the LCD panel in a netbook (Asus Eee PC 1005)

  - by neilfein

  Yesterday, I was cleaning up and dropped my Asus Eee 1005PE. The screen is cracked inside (i.e., cracks are visible only when on), and no longer works properly. I booted up with another monitor attached, and the computer itself is fine, but needs a new screen. Best Buy wants at least $250 to repair it (that includes their $150 fee to breathe in the same room as the unit), and Asus was of no help at all. (They're incredibly cagey and won't provide any money numbers at all, not even the cost of the part.) If replacing the LCD is no more trouble than replacing memory or a hard drive, I can do that. It's within my means to buy the part (18G241010402, a TFT LCD), but I'd like to know more about the procedure involved. My question: How does one replace the screen in this unit? Do I simply open the case and swap out the unit, or do I need to disassemble anything else to get to the screen? I don't want to order the part and then end up in a situation like this. Is the case screwed shut, or is it like an iPod where they glue things closed? I know enough about my abilities with a soldering gun to not attempt to solder tiny wires, would any of that be involved?

  Read the article

• Could I use Windows 7 instead of Windows SBS 2008 for this server?

  - by Ecyrb

  First off, I'm not a sys admin. I'm just a software developer trying to help out my parents' small business. Right now they have one server, a domain controller with a P4 processor running SBS 2003. They also have this machine hosting QuickBooks, MySQL for the old version of an app, and SQL Server 2008 Express for the new version of the app (which will replace the old eventually). They've been complaining about the workstations being slow so I figured it might help if they bought a new server and moved QuickBooks, MySQL, and SQL Server to the new server, leaving the old server as just a DC. In trying to pick an operating system for their new server, I was thinking about Windows SBS 2008 Standard with enough licenses for seven machines. But that's a lot more money than they're going to want to spend. So then I wondered if there's any real advantage to having a server OS as opposed to just throwing Windows 7 on the new server. It's a lot cheaper and I can't think of any SBS features that it would need if it's just hosting QuickBooks, MySQL, and SQL Server. Would it be okay to use Windows 7 for a server like this? Are there any advantages to using SBS 2008 that I would be missing out on? Any additional tips are much appreciated!

  Read the article

• Can not boot windows XP from cloned hard disk - what can I do?

  - by Martin

  My configuration: a PC (some years old) with MSI K8N-Neo-4F Motherboard, 1 GB RAM. Disk 1 (Maxtor, SATA II, 250 GB): 2 Partitions, on Partition 1 (48 GB): Windows XP Professional (NTFS) on Partition 2 (190 GB): data (NTFS) I wanted to have a larger and faster disk (the PC is incredibly slow and permanently the disk is rattling when I try to open an application or during Windows startup), so I took Disk 2 (Seagate, Sata II, 500 GB), installed in the PC, created at first a 400 GB-partition at the end of the disk and cloned the data to it, which worked well Installed a swap partition and a partition for Ubuntu Linux 12.10 on the first "part" of the disk so I was able to boot Linux and the old Windows XP with the Linux "System selection" at startup. Now I wanted to move Windows XP to the new disk, deleted the Linux partitions cloned Windows XP to the new disk (with free tools - EASESUS), left both disks in the PC and tried to select the new hard drive during boot as boot partition. This did not work, the PC refused to boot from this second disk. I tried many things like making the boot partition on the 2nd drive "active" in the Windows System Preferences modifying the boot.ini file to boot from the second disk - tried to boot from it, but ended with an error message stating that it was not possible to boot from this disk because of a hardware failure or something else or so removing the original disk and plugging the new one on the same SATA port as the original one - also booting failed with an error message repairing the MBR by booting into recovery mode from the Windows XP Installation CD-ROM, selecting the second disk and doing "FIXMBR" which said that everything was fine with the MBR. after that at least the PC tried to boot from the newer disk and then startup was hanging during the blue screen with the Windows Logo.... no luck. ... deleting the cloned partition and cloning again - this time with Macrium Reflect Free version... - no success during booting. I tried a lot of things with no success, so I wonder what I am doing wrong?! What could I do to successfully clone my Win XP partition to replace the original disk by a larger one which is bootable.

  Read the article

• Utilities for finding x/y screen coordinates

  - by slothbear

  I have an application that needs the user to enter the x and y location of a couple of items on the screen. [Yes, this is crap and I'll replace it, but for now...] On Mac OS X, I'm using Snapz Pro X. When I choose to take a snap of a selection, the interface displays the mouse cursor location. This is OK for my personal use, but I can't ask users to buy a $69 program for this function. I thought I had a solution with the built-in program "Grab", but it reports the coordinates from the bottom left, and I need it from the top left. I don't have access to Windows; not sure what to use there. I've not even been able to come up with good search terms since mouse and coordinates and x/y are so common. Ideas are welcome there. Extra credit: same x/y finder for Linux. A Java program would be OK too, since the main application is in Java.

  Read the article

• Recommended Win2k8 Server software to fix my RAID-0 issue

  - by Jason Kealey

  I'm running an Asus P6T V2 Deluxe. It has six SATA ports and supports onboard RAID. I am using two of those ports for a RAID0 array of 1.5TB Seagate drives using the onboard RAID controller. One of them is giving me SMART warnings and I want to preemptively replace it. I pulled out two other 1.5TB drives from another computer and am ready to use one or both, if necessary. I can't run any SMART diagnostic software from within Windows because it only sees the hardware RAID-0 array, not each individual drive. The first thing I tried was a slow sector-by-sector copy using a free tool called EASEUS Disk Copy. Used the bootdisk, copied (took like 16 hours), unplugged the defective drive and plugged the new one in its place. The motherboard didn't recognize the new drive as being part of the known setup, so it did not want to boot. The second thing I tried was using other software (I forget the name) to copy the partition from within Windows. The first software failed because I had a server operating system. I found another software (I forget the name) which supported a server OS and did a partition copy onto the new drive. This seemed to work and the OS started to boot, but blue screened and started a reboot cycle. I'm assuming the software I was using was no good as it was trying to copy the boot disk while it was in use. I am looking for recommendations on what software to use to fix my problem without doing a re-install. Everything is backed up but my computer works fine and I'd like to avoid re-installation when possible. However, my system would be back up now if I had just started over on a second RAID array. :)

  Read the article

• Use autocomplete in dropdown cells with Excel 2007?

  - by Martin

  I want to make a survey with Excel and I therefore have defined the cells for the answers as a dropdown cell which only accepts answers from a certain list, e. g.: The two Lists List1 and List2 (yellow cells) are the possible answers for the questions in Block 1.x resp. 2.x (blue) . There might be a block 4 with more questions, which again use List1 for their possible answers. My problem is: I'd like to be able to use the autocompleate feature to fill in the blue cells with the dropdown menu, so that the user only types 5 and it automatically expands to "5: extremely important" or "5: extremely difficult". According to my research on the www, this should be possible if I add the list with possible answers directly above the cells where autocomplete should work (I did this with the green helper cells which could be hidden) . But I have to enter at least 4 characters 5: e to get the autocompleted suggestion. Is there a way to make autocomplete already replace a "5" by the corresponding valid term? As the survey file shall be distributed to a lot of people "outside", I can not use VBA magic because it may be blocked on their computer and might not work. EDIT: it seems to have to do with the numbers I use: If I'd start my List items with A, B, C instead of 1, 2, 3, it would work perfectly. Excel seems to ignore the pure numbers when they are entered and does not try to autocomplete them.. is there a workaround? (I hope it is clear what I want, it seems a little difficult to explain.)

  Read the article

• P2V Wouldn't Boot, Rebuilt initrd, Need to Clean Up

  - by Mike Soule

  We have a CentOS 5.4 server (build 2.6.18-164.el5xen). We went to P2V this server so we can have redundancy, the physical only has one PSU. The P2V only completed 99% of the way, we have a VMWare ticket opened, but they marked the ticket as low priority. I was able to boot into a rescue disc of Red Hat 5.4 and rebuild the initrd with the help of this blog post. Now the only issue is the original server had a modified initrd, which was also from a different OS build and made by an outside provider. We do not have a document outlining modifications. My question is, is it at all possible to copy the initrd off of the physical server and replace it on the virtual and some how have the virtual machine boot? Thanks for any input. Edit: I copied the initrd img from the physical and it recreated the original issue. Here is a screen capture of the error. http://i.imgur.com/MqC73.jpg Edit2: echo Scanning logical volumes lvm vgscan --ignorelockingfailure echo Activating logical volumes lvm vgchange -ay --ignorelockingfailure VolGroup00 resume /dev/VolGroup00/LogVol01 echo Creating root device. mkrootdev -t ext3 -o defaults,ro /dev/VolGroup00/LogVol00 echo Mounting root filesystem. mount /sysroot

  Read the article

• How do I restore tab-completion on shell variables on the bash command-line?

  - by Eric

  I've long set my most-recently visited directories to shell variables d1, d2, etc. On an ancient Fedora machine I could type a command like $ cp $d1/ and the shell would replace $d1 with text like /home/acctname/projects/blog/ and would then show me the contents of .../blog, like any tab-completion. Now, both ubuntu wheezy/sid and fedora 16 just -escape the '$', and naturally there are no completions to show. You can see this behavior in action in an OSX Terminal window. On 10.8, do something like ls $HOME/ to see what I mean. Is there a bash shell variable or option that can restore the old behavior? man bash suggests this is a bug: complete (TAB) Attempt to perform completion on the text before point. Bash attempts completion treating the text as a variable (if the text begins with $), username (if the text begins with ~), hostname (if the text begins with @), or command (including aliases and functions) in turn. If none of these produces a match, filename completion is attempted. I get the above described completion when a token starts with '~' or a letter. It's just '$'-completion that's broken.

  Read the article

• Adding more drives to a drive array

  - by Mystere Man

  I have a friend who has two servers, a Dell 1800 and an HP 350 ML G5, both have SAS drive arrays. The Dell is a 3.5" and the HP is a 2.5". They currently only have 3 drives in each array. We want to add additional drives, but they do not appear to have caddies, just "fake" covers. I haven't been able to take a good look at them, so I'm not sure what I need to do here. Are the "sockets" just there, and I can buy additional caddies and just stick them in? Or do I have to buy some kind of caddy adapter? Also, i'm thinking of just going 2.5" in the new server, so is there a 2.5" adapter caddy that will fit in the 3.5" chassis for the Dell, so I can use 2.5" drives in the 3.5" chassis? Can I buy 6GB/s drives and add them to the 3GB/s controller? The reason is that we're going to replace both computers in a year or so, and we want to bring the drives with. So rather than buy 3GB/s drives, we just want to buy 6GB/s drives so they can be used in the new server.

  Read the article

• How do I encapsulate the application server from the web and database servers?

  - by SNyamathi

  So I've been doing some reading and it seems like the best practice would be to have separate database, application, and web servers. There are a few things that I've failed to understand - please feel free to recommend any reading materials that would address these topics. Database (assume MySQL) Application server communication: Does the database server do any sort of checks on the SQL commands sent / returned, or is it just a "dumb pipe" that responds to SQL commands by spitting back data? Application server (assume Tomcat) Web Server Almost the reverse here, is it the web server that is more of a pipe to the internet that forwards requests to the application server and spits back responses? I'm not wording this well, but I'm trying to ask - is it the application server that is responsible for validating data received by from requests? ex: Parsing POSTs Validating user logins Encrypting decrypting data Furthermore, how do these two servers communicate? I'm trying to keep things as flexible as possible here, so while I could write a web server in Java and use Java to communicate between the web and app server, that doesn't sound very modular. What if I want to use Python or some other language to replace the web server later on? What if I want to make a non-web facing application used in house written in C++ or something.

  Read the article

• pcfg_openfile: unable to check htaccess file, ensure it is readable

  - by rxt

  After moving a website folder on my local development machine to another drive, then moving it back, I got a 403 error. Most of this problem had probably to do with rights that got messed up. After deleting the code and restoring it from SVN, the rights seemed allright. The error stayed however. The setup is a bit complex, as follows: I have Ubuntu 10.4 as development machine, trying to mimic the server as much as possible We use Eclipse + SVN and I create all projects in a local folder under my user account In /var/www-vhosts I create folders for each vhost, like this one: test.localhost test.local/index.php: includes the index file of the project test.local/.htaccess is a dynamic link to the htaccess file in a project subfolder I get the following error in the apache error log: [Thu Jul 08 15:55:56 2010] [crit] [client 127.0.0.1] (13)Permission denied: /var/www-vhosts/test.localhost/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable The problem seems to be the .htaccess file, or the link to it. When I empty the htaccess, nothing changes When I remove the link, the index-include produces some output (in the apache error log) When I remove the link and replace it with the actual file, I get another error: [Thu Jul 08 16:47:54 2010] [error] [client 127.0.0.1] Symbolic link not allowed or link target not accessible: /var/www-vhosts/test.localhost/test I'm lost here, don't know what to do next. Do you have any ideas what I can try? This setup has worked before, but I don't know what is different now.

  Read the article

• Cannot write to directory after taking ownership

  - by jeff charles

  I had a directory on an internal hard-drive that was created in an old Windows 7 install. After re-installing my operating system, when I try to create a new directory inside that directory, I get an Access Denied message. This isn't a protected directory, just a random directory I created at the drive root (that drive was not the C drive in either install). I tried to take ownership by opening folder properties, going to the Security tab, clicking on Advanced, going to Owner tab, clicking on Edit, selecting my user account, checking Replace owner on subcontainers and objects, and clicking Apply. There were no error messages and I closed the dialogs. I rebooted, checked the owner on that folder and a couple subfolders and it appears to be set correctly. I am still getting an Access Denied message however when trying to create a directory in it. I've also tried using attrib -R . to remove any possible readonly attribute inside the directory in an admin command prompt but am still unable to create a directory using a non-admin prompt (it does work in an admin prompt). Is there anything I can do to get write access to that folder and it's subcontents in a non-elevated context without disabling UAC?

  Read the article

• Centos repository packages vs latest developer release

  - by fran

  I have started to run a personal server using CentOS and I have noticed that many packages that are available to install from repository are old compared with the latest release from the developer. I know that installing packages from repository is very easy and I guess that the supplied versions are stable and prepared to work without any trouble, but I still find odd having so much software that lags behind the current version. It's my first time with linux and I don't know what is the "normal" thing, should I stick to whatever version the repository supplies, or try to get the latest from the developer? To be more precisely, the repository supplies the apache httpd web server with version 2.2, I wanted to update to 2.4, so I started removing apache and its dependencies packages that come with centos to use the latest ones, but when I was about to remove pcre v6 to replace it with v8, i found out that 132 installed packages depend on it and probably it is not a good idea to remove it, so that made me think twice about getting the latest software instead of using the packages supplied by the official repositories. Should I leave things as they are instead of going on an upgrade rampage? Thanks

  Read the article

• I think my laptop just died

  - by Joel Coehoorn

  I have a Dell 1330M that as of about 15 minutes ago will no longer POST. What happened was I was working, stepped away for a moment, and when I came back it was turned off. I thought that was odd, but turned it on and things seemed fine. About 1/2 hour later it crashed and restarted, but came up fine again. It did this once more. At this point I was starting to get worried, but I hadn't had any problems with the laptop before and every crash was after doing some work in a virtual machine that I don't often use, so I at put the blame there. It didn't feel like it was overheating anywhere and there's no ozone smell of overheated electronics. Then it crashed a final time and now when I turn it on all I see is a bright screen with a bunch of vertical lines (noise). I've tried removing the memory sticks one at a time, but I get the same result with either memory stick in either slot. With no memory at all it stops earlier in the POST process and the screen is completely blank (black, no backlight). As I type this, I hear a double beep from the system about once every 10 minutes. I'm pretty sure the hard drive is fine because it fails during post, before anything off the drive is needed. The power supply seems good because the screen is nice and bright. It's not the RAM because swapping that around made no difference. The leaves motherboard (which I doubt and can replace) and CPU (which just might be changable). Any ideas? Is there any hope for this laptop? I'm rather fond of it and I'd have a hard time replacing it with anything near as nice.

  Read the article

• iCloud backup merges or overwrites?

  - by Joe McMahon

  The following happened today (it was six AM my time, so yeah, I was dumb and dropped stitches in this process): A friend had a problem with her iPhone and needed to reset it. Unfortunately she did the reset while connected to iTunes and the restore process kicked in. In my sleepy state, I told her to go ahead. She did, and restored the most recent local (iTunes) backup (from July last year - she doesn't back up often, as she has an Air which is pretty full). During setup on the phone, she was prompted to merge data with the iCloud copy, and did so. There was no "restore from iCloud" prompt. Obviously I should have made sure she was disconnected from iTunes before she did the reset, or had her set it up as a new device and then restored from iCloud, but water under the bridge now. (Side question: could I have had her disconnect and then restart the phone again and avoid this whole process?) The question is: was the "merge" that happened in this process a true merge, or a replace? Her passwords for Mail were wrong, since they were the old ones from the old backup. If she does the wipe data and restore from iCloud, will she get her old SMSes and calendar entries back? Or did the merge decide that the phone, despite it being "old" was right and therefore the SMSes, calendar entries, etc. were discarded? As a recovery option, I have a 4-day-old iTunes backup here from ~/Library/Application Support/MobileSync/Backup, but she and the phone are 3000 miles away, and it's 8GB, so I can't easily restore it for her. I do have the option of encrypting it and mailing it on a data stick if the iCloud backup is now toast. Should she try the wipe and restore from the cloud (after backing up locally), or should I just get the more-recent backup in the mail? My goal is to get everything (especially the SMSes) back to the most recent version possible.

  Read the article

• Windows drive letters A: and B:

  - by Workshop Alex

  This is a question that just popped into my mind and I can't help but wonder why it's still common for a Windows installation to be installed on C: with all other drive letters going up from D: to Z:. In the early MS-DOS times, all we had were floppy disks and they were at A:. When the 3.5 inch floppy started to replace the 5.25 floppy, many people had an A: and B: drive. Then the hard disk became popular and the hard disk was at C: because A: and B: were taken. Then the 5.25 floppy disappeared and most computers had a gap between A: and C:. Nowadays, the 3.5 floppy is just too outdated so A: disappeared too. All disks now start at C:. Yeah, I know I can assign my own drive letters and I've done so with my data disks. My installation disk will just continue to be stuck at C: and I don't really mind. I have no problems with drive letters. But why do the new Windows versions just continue to install themselves by default on C: instead of assigning the letter A: to the boot hard disk?

  Read the article

• GRUB reporting wrong partition type

  - by plok

  It all started when I had to replace one of the disks that the software RAID 1 on this machine currently uses. From that moment on I have not been able to boot to the Windows XP that is installed on the fourth hard drive, /dev/sdd. I am almost positive that the problem is related not to Windows but to GRUB, as if I unplug all the other hard drives so that the Windows XP disk is now /dev/sda it boots with no problem. The problem seems to be that GRUB detects a wrong partition type, which I understand suggest that something is really messed up. This is what I get when I try to follow the steps that until now had worked like a charm: grub> map (hd0) (hd3) grub> map (hd3) (hd0) grub> root (hd3,0) Filesystem type is ext2fs, partition type 0xfd 0xfd? That doesn't make sense. /dev/sdb and sdc are 0xfd (Linux raid), but not /dev/sdd: edel:~# fdisk -l [...] Disk /dev/sdd: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00048d89 Device Boot Start End Blocks Id System /dev/sdd1 * 1 30400 244187968+ 7 HPFS/NTFS edel:/boot/grub# cat device.map (hd0) /dev/sda (hd1) /dev/sdb (hd2) /dev/sdc (hd3) /dev/sdd I have been trying to work this out for hours, to no avail. Can anyone point me in the right direction?

  Read the article

< Previous Page | 217 218 219 220 221 222 223 224 225 226 227 228  | Next Page >