Search Results

Search found 18488 results on 740 pages for 'android networking'.

Page 245/740 | < Previous Page | 241 242 243 244 245 246 247 248 249 250 251 252  | Next Page >

• Hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• Copy all bridge traffic to a specific interface

  - by Azendale

  I have a bridge/switch set up an a machine that has multiple ports. Occasionally, I have a vm running through virtualbox, and I'll have it use a virtual adapter and then I add the adapter to the bridge. I have heard that some switches can copy all the traffic they see to a specific port on the bridge, usually for network monitoring. I would like to be able to run some windows based network tools. I do not want to run Windows on the actual hardware, because it would be lots of work to duplicate my setup in windows, so I was thinking if I can copy all traffic to a port, I can send it to a VM with windows. How can I set this up? I think this might be ebtables area, but I don't know ebtables well enough to know for sure, and it always seems like (from my understanding of ebtables) ebtables does something with the traffic (drop, accept, etc), but never copies it.

  Read the article

• Why would 70-persistent-net.rules have no effect?

  - by Wes Felter

  I've got a saucy server with a lot of NICs and they end up with weird names like "rename19". I know interface names can be changed by modifying the /etc/udev/rules.d/70-persistent-net.rules file. The first clue that something is wrong is that that file did not exist even though it's supposed to be created automatically. So I decided to write my own based on advice from Linux From Scratch: ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:06:00.0", NAME="eth0" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:06:00.1", NAME="eth1" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:06:00.2", NAME="eth2" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:06:00.3", NAME="eth3" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:0c:00.0", NAME="mezz0" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:0c:00.1", NAME="mezz1" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:1b:00.0", NAME="slot1a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:1b:00.1", NAME="slot1b" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:20:00.0", NAME="slot2a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:20:00.1", NAME="slot2b" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:11:00.0", NAME="slot3a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:11:00.1", NAME="slot3b" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:8b:00.0", NAME="slot4a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:8b:00.1", NAME="slot4b" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:90:00.0", NAME="slot5a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:90:00.1", NAME="slot5b" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:95:00.0", NAME="slot6a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:95:00.1", NAME="slot6b" (I'm matching on PCI IDs instead of MAC addresses because I have multiple identical machines that I want to apply this configuration to.) After rebooting, nothing has changed. It's like these rules aren't even being read. There's not much going on in dmesg either: $ dmesg | grep udev [ 3.196629] systemd-udevd[323]: starting version 204 [ 6.719140] systemd-udevd[550]: starting version 204 [ 38.695050] init: udev-fallback-graphics main process (1658) terminated with status 1

  Read the article

• Implementing the transport layer for a SIP UAC

  - by Jonathan Henson

  I have a somewhat simple, but specific, question about implementing the transport layer for a SIP UAC. Do I expect the response to a request on the same socket that I sent the request on, or do I let the UDP or TCP listener pick up the response and then route it to the correct transaction from there? The RFC does not seem to say anything on the matter. It seems that especially using UDP, which is connection-less, that I should just let the listeners pick up the response, but that seems sort of counter intuitive. Particularly, I have seen plenty of UAC implementations which do not depend on having a Listener in the transport layer. Also, most implementations I have looked at do not have the UAS receiving loop responding on the socket at all. This would tend to indicate that the client should not be expecting a reply on the socket that it sent the request on. For clarification: Suppose my transport layer consists of the following elements: TCPClient (Sends Requests for a UAC via TCP) UDPClient (Sends Requests for a UAC vid UDP) TCPSever (Loop receiving Requests and dispatching to transaction layer via TCP) UDPServer (Loop receiving Requests and dispatching to transaction layer via UDP) Obviously, the *Client sends my Requests. The question is, what receives the Response? The *Client waiting on a recv or recvfrom call on the socket it used to send the request, or the *Server? Conversely, the *Server receives my requests, What sends the Response? The *Client? doesn't this break the roles of each member a bit?

  Read the article

• You made it through the Interview, Now What?

  - by Jonathan Kehayias

  This is somewhat of a continuation post to my previous blog post, “Some thoughts on Interviweing…” .  Now that you survived the interview process, what do you do?  This is a common area of discomfort for people interviewing for  any kind of job, not just positions dealing with SQL Server.  In this post I’d like to focus on a topic that I like to refer to as “Post Interview Etiquette” and how it might impact your ability to get hired for a position.  Whether or not to follow-up...(read more)

  Read the article

• Do I need social networks to be an expert developer? [closed]

  - by Gerald Blizzy

  This question may sound odd, but do I need twitter, facebook and google+ if I am a web-developer? I see many expert developers nowadays using it in working order. It seems like it's harder to stay in touch with customers, co-workers and potential customers if you don' use social networks. Am I right? Reason why I ask is that I am totally not a facebook/twitter person, I find it boring and annoying. I understand that linkedin is usefull for career, but what about twitter and facebook? Are they needed for web-developer career? What I am trying to ask is if I only use linkedin, own portfolio website, google talks, gmail and something like github, would I actually miss anything professionally/job-wise? My thoughts are that I can just have my portfolio website where I list all my projects aswell as contacts page with my google talks/gmail account. It can suit both fulltime job, freelance and own projects. So this way email and google talks is just enough. Am I right or not? Thanks in advance!

  Read the article

• PPTP VPN connects via NM but goes down during SSH connection

  - by Andrea Olivato

  I setup a VPN PPTP connection via network manager and it connects correctly (I see the lock near the notification icon and the message "Vpn connection has been successfully...") As soon as I try to perform any SSH connection via the established tunnel the connection itself goes down with the message "Vpn connection failed". the SSH connection always fails at debug1: SSH2_MSG_KEXINIT sent I've looked into the system logs and this is the log Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> Starting VPN service 'pptp'... Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 7093 Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN service 'pptp' appeared; activating connections Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: init (1) Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: starting (3) Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN connection 'Redation' (Connect) reply received. Dec 12 12:25:05 ushuaia NetworkManager[1155]: <info> VPN connection 'Redation' (IP4 Config Get) reply received from old-style plugin. Dec 12 12:25:05 ushuaia NetworkManager[1155]: <info> VPN Gateway: 5.98.141.210 Dec 12 12:25:06 ushuaia NetworkManager[1155]: <info> VPN connection 'Redation' (IP Config Get) complete. Dec 12 12:25:06 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: started (4) Dec 12 12:25:14 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: stopping (5) Dec 12 12:25:14 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: stopped (6) Dec 12 12:25:14 ushuaia NetworkManager[1155]: <info> VPN plugin state change reason: 0 Dec 12 12:25:15 ushuaia NetworkManager[1155]: <warn> error disconnecting VPN: Could not process the request because no VPN connection was active. Dec 12 12:25:20 ushuaia NetworkManager[1155]: <info> VPN service 'pptp' disappeared Please note that the same vpn is configured on my colleagues Windows 7 and works without problem when they use putty to connect via SSH

  Read the article

• Bash script won't stay open in background after running through while

  - by jfreak53

  I can't get the following bash script to stay open after the first message is received from NC: #!/bin/bash port=3333 nc -l $port | while read msg; do notify-send Alert "$msg"; done After the first message it exits. I want it to stay open and continue monitoring for new messages from NC. I know that if I launch nc -l port without the while loop it stays open and I can chat away between the two connections even disconnect from the connected host. I am sending the message using: echo 'done' | nc IP port

  Read the article

• Ask HTG: Disabling Windows Startup Programs, Using DNS Names on Your Home Network, and Restoring a Vintage Keyboard

  - by Jason Fitzpatrick

  Once  a week we round up some of the answers we’ve sent out to readers and share them with everyone. This week we’re looking at removing programs from the Windows startup routine, using DNS names on the local network, and restoring a vintage keyboard. HTG Explains: Do You Really Need to Defrag Your PC? Use Amazon’s Barcode Scanner to Easily Buy Anything from Your Phone How To Migrate Windows 7 to a Solid State Drive

  Read the article

• ralink rt2860 not working anymore in ubuntu 12.10

  - by greenit

  I just upgraded from Ubuntu 12.04 to 12.10, however, my network card is not working anymore... When i had 12.04 installed, i just had to download the driver from Ralink, go to the directory and enter these commands: $ make $ sudo make install and the network card worked... now, when I want to do this in ubuntu 12.10, it seems like it works, but it doesn't. I can enable the module, it recognizes the network card, but i am unable to connect to any wireless network... How can i get my wireless card working again? If any1 knows a solution, please tell it to me, thx in advance

  Read the article

• Connectify Dispatch Links Multiple Network Nodes Into a Mega Connection

  - by Jason Fitzpatrick

  Connectify Dispatch wants to change the way you interact with the networks around you by making it dead simple to mesh all available Wi-Fi, Cellular, and Ethernet connections into a massive and stable pipeline. Dispatch makes it open-and-click easy to hook up multiple Wi-Fi nodes, your cellphone, and even Ethernet connections into a single blended connection. While the video above gives a great overview of the process, check out the video below to see it in real world action: The project is currently in the last phase of KickStarter funding, so now is a great time to score Connectify Dispatch at a steep discount–pledging as little as $10 to fund the project, for example, scores you 50% of a 6-month Pro license. Hit up the link below to read more about the project, check the KickStarter status, and see all the neat features in the development pipeline. Dispatch: The Internet, Faster. [KickStarter] HTG Explains: What The Windows Event Viewer Is and How You Can Use It HTG Explains: How Windows Uses The Task Scheduler for System Tasks HTG Explains: Why Do Hard Drives Show the Wrong Capacity in Windows?

  Read the article

• Forward TCP Connections with Iptables

  - by opc0de

  I receive connections to my server from several ip addresses I want to route these connections just like rinetd does but based on the ip the connection is coming from to connect to a specified host. Just like this: IP 10.10.12.1 => CONNECTS TO MY SERVER => MY SERVER REDIRECTS IT TO 82.12.12.1 IP 10.10.12.2 => CONNECTS TO MY SERVER => MY SERVER REDIRECTS IT TO 81.121.12.10 etc Is it possible or do I need to write my own daemon to achieve this functionality ?

  Read the article

• No internet access when I'm connect to my company's VPN

  - by Iago

  I googled my problem and I've read some questions in Ask Ubuntu, but I didn't solve my problem. I connect to a PPTP VPN server and it works well, but when I'm connected to that VPN I don't have Internet access but private network access. If I check "Use this connection only for resources on its network", I have Internet access, but this way I haven't access to my company's private network. What's the problem? Help, please.

  Read the article

• Install reliance Driver software in ubuntu 14.04

  - by A Umar Mukthar

  I'm Using Huawei ec 150 dongle. I need to install driver software It is quiet a big task for begineers in linux. So i took this matter over here. EDIT Output of lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 003: ID 12d1:140b Huawei Technologies Co., Ltd. EC1260 Wireless Data Modem HSD USB Card Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 046d:c05a Logitech, Inc. M90/M100 Optical Mouse Bus 002 Device 002: ID 046d:c31d Logitech, Inc. Media Keyboard K200 Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

  Read the article

• Google I/O 2012 - Building Android Applications that Use Web APIs

  Google I/O 2012 - Building Android Applications that Use Web APIs Yaniv Inbar Google offers a large and growing set of back-end services, from AdSense to Tasks to Calendar to Google+, that can enrich your app, and increasingly they have a uniform set of APIs. This session discusses how to use them efficiently and securely, including authenticating safely and with good user experience, and describes Android-specific app-level optimizations. For all I/O 2012 sessions, go to developers.google.com From: GoogleDevelopers Views: 563 12 ratings Time: 55:14 More in Science & Technology

  Read the article

• 12.04, nvidia-settings makes one of my dual monitors grey and useless, disables network

  - by Kerrick

  I'm running Ubuntu 12.04 64-bit, Precise Pangolin, with a PNY GTS 250 1GB video card and a monitor plugged into each of the DVI ports. I'm using the proprietary drivers (post-release updates). If I set anything to do with Separate X Screens up in nvidia-settings (and write it to xorg.conf and reboot), my second monitor has a grey background, no menu bar, no ability to have a window on it, the second monitor doesn't get picked up in a screneshot, and if I move my mouse cursor to it it's an ugly black X. Plus, my network is unable to connect to anything. If I subsequently delete /etc/X11/xorg.conf and reboot, everything goes back to working, albeit with a single monitor activated. If I set anything to do with TwinView up in nvidia-settings, my second monitor starts working, but it isn't seen as a second monitor by Ubuntu, so I can't apply color calibration to it separately. Plus, my mouse gets "caught" between the monitors every time I try to move my cursor between the two. What gives? If it helps, this is the xorg.conf that nvidia-settings generates for Separate X Screens.

  Read the article

• How to set multiple nameservers in /etc/resolv.conf which sticks on reboot?

  - by chrone

  Ubuntu 14.04 Server edition only displays "nameserver 127.0.0.1" in "/etc/resolv.conf" on each reboot if the dns-nameservers in "/etc/network/interfaces" contains 127.0.0.1 and some other DNS such as Google Public DNS. On /etc/network/interfaces I set as follows: dns-nameservers 127.0.0.1 8.8.8.8 But after a reboot, /etc/resolv.conf gives me this: nameserver 127.0.0.1 Shouldn't the "nameserver 8.8.8.8" listed in the /etc/resolv.conf too? Thanks in advanced.

  Read the article

• Problems connecting to eduroam wifi - ubuntu touch

  - by Fiona Cox

  I am trying to connect to our university's eduroam wi-fi network with my Nexus 4 running Ubuntu touch (utopic latest build), but can't get past the first stage. I wonder if anyone can help please? I am following these instructions (which worked for my iPhone): http://www.st-andrews.ac.uk/itsupport/mobile/eduroam/ But when I go to the bandit.st-andrews.ac.uk/connect page then follow the link to 'eduroam setup' I get the error message: Authorization Required This server could not verify that you are authorised to access the document requested. Either you supplied the wrong credentials (e.g., bad password), or your browser doesn't understand how to supply the credentials required. Apache/2.2.16 (Debian) Server at bandit.st-andrews.ac.uk Port 443 (Clearly it's the latter option (browser) as I haven't been asked for my credentials yet.) Is there a way round this, or am I just not going to be able to connect until further down the Ubuntu touch development road... Thanks!

  Read the article

• Network icon shows an Internet connection, while ping does not

  - by mushfiq

  I am an Ubuntu user for the last couple of years. Recently facing problem to connect my new laptop into the Internet. I have an ISP connection which provide me a NAT address. I changed all the information in network configuration.The network icon shows it is connected to Internet but when I browse, ping shows no Internet connection. /etc/network/interfaces look like this: auto eth0 iface eth0 inet static address 192.168.100.118(put you internet address provided by the ISP) gateway 192.168.100.1(gateway address) netmask 255.255.255.0 network 192.168.100.0 And when I ping my DNS server IP get the reply from DNS server. I can not understand the problem,it should be mentioned that I also changed the Physical address of my laptop for using the existing connection. In windows the connection is working fine. Any suggestion in this question will help me a lot. Thanks in advance.

  Read the article

• No client internet access when setting up these iptables rules

  - by Siriss

  I have read many other posts but cannot figure this out. eth0 is my external connected to a Comcast modem. The server has internet access with no issues. eth1 is internal and running DHCP for the clients. I have DHCP working just fine, all my clients can get an IP and ping the server but they cannot access the internet. I am using ISC-DHCP-SERVER and have set /etc/default/isc-dhcp-server to INTERFACE="eht1" Here is my dhcpd.conf file located in /etc/dhcp/dhcpd.conf ddns-update-style interim; ignore client-updates; subnet 10.0.10.0 netmask 255.255.255.0 { range 10.0.10.10 10.0.10.200; option routers 10.0.10.2; option subnet-mask 255.255.255.0; option domain-name-servers 208.67.222.222, 208.67.220.220; #OpenDNS # option domain-name "example.com"; default-lease-time 21600; max-lease-time 43200; authoritative; } I have made the *net.ipv4.ip_forward=1* change in /etc/sysctl.conf here is my interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp iface eth1 inet static address 10.0.10.2 netmask 255.255.255.0 network 10.0.10.0 auto eth1 And finally- here is my iptables.conf file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *nat :PREROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.10.0/24 -o eth0 -j MASQUERADE #-A PREROUTING -i eth0 -p tcp --dport 59668 -j DNAT --to-destination 10.0.10.2:59668 COMMIT *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -i eth1 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 53 -j ACCEPT -A INPUT -m state --state NEW -m udp -p udp --dport 53 -j ACCEPT -A FORWARD -s 10.0.10.0/24 -o eth0 -j ACCEPT -A FORWARD -d 10.0.10.0/24 -m state --state ESTABLISHED,RELATED -i eth0 -j ACCEPT -A FORWARD -p icmp -j ACCEPT -A FORWARD -i lo -j ACCEPT -A FORWARD -i eth1 -j ACCEPT #-A FORWARD -i eth0 -m state --state NEW -m tcp -p tcp -d 10.0.10.2 --dport 59668 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT I am completely stuck. I cannot figure out why the clients cannot access the internet. Am I missing a service? Is a service not running? Any help would be greatly appreciated. I tried to be as thorough as possible but please let me know if I have missed something. Thank you!

  Read the article

• Create personal wireless network on laptop

  - by TechGuru

  I have a WiFi Network, now I have connected my laptop to the WiFi Network. And it is working fine I'm able to access the internet via WiFi. But I want to create other network on my laptop so that I can connect my mobile phone to the my laptop network. Means, my laptop is already connected to WiFi network (xyz). Now I want to create one wireless network on my laptop. So that I can connect my mobile phone to laptop network and access the internet on mobile. But I don't want to lost my `laptop and WiFi connection that is already connected. I tried to create the wireless network on my laptop, but when I created my personal wireless network I lost my wifi-laptop connection. I don't know it is possible or not.

  Read the article

• Jquery website is not opening in UBUNTU but in XP, Everything is fine

  - by Raman Sethi

  I know it is weird, But I just discovered this, jquery.com is not opening in my ubuntu firefox or other KDE browser and hence many sites that copy codes from code.jquery.com also hanged. Is there any solution to this problem. I have found the problem It is actually with the DNS servers I am using, Google DNS, 8.8.8.8 and 8.8.4.4, whenever I use these DNS in ubuntu my system stop responding to some sites, actually they are connected nicely, but the request end up in waiting.. I dont understand why...??? I checked my DNS with cat /etc/resolv.conf Even after using Google DNS, it is showing DNS servers I received automatically after connecting to the service provider. I am connecting using Network Manager, not using DNS I provided but using the default one. Any Solution??

  Read the article

• Changes to 'resolveconf' discarded when connecting to a new network

  - by sudheer

  I have upgraded to 12.10 from 12.04 recently and I am having issues with connecting to the Internet. I got an IP address and am able to ping other LAN IPs in the local network but I am unable to connect to the Internet and am even unable to ping www.google.com from a terminal. Somehow making changes in /etc/resolv.conf and restarting resolvconf service and rebooting works but I need to do this every time I connect to a new network. How do I make these changes permanent? Can someone suggest a solution to this issue?

  Read the article

• Cannot authenticate to SBS 2003

  - by Lerp

  I am trying to connect my machine to my work's entirely windows network and I am having a few issues: Whenever I try to access the server, the authentication dialog just keeps popping back up. I cannot connect to the printers (it says connecting to device failed) I have tried setting up samba, winbind, kerberos, likewise open all to no avail. I have a feeling I am just setting them up wrong. My nautilus shows this when I go to Network Windows Network MASTERMAGNETS I can ping both MASTERMAGNETS.LOCAL and 192.168.0.2 after modifying my /etc/hosts james@jamesmaddison:~$ cat /etc/hosts 127.0.0.1 localhost jamesmaddison 192.168.0.2 MASTERMAGNETS.LOCAL 192.168.0.50 Sharp-Printer # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters I believe that's the correct domain (not sure if that's the correct term) as when I do nslookup MASTERMAGNETS.LOCAL I get the following: james@jamesmaddison:~$ nslookup MASTERMAGNETS.LOCAL Server: 192.168.0.2 Address: 192.168.0.2#53 Name: MASTERMAGNETS.LOCAL Address: 192.168.0.3 Name: MASTERMAGNETS.LOCAL Address: 192.168.0.2 It all worked fine before I reinstalled Ubuntu and now I just cannot get access to the server. All help is appreciated, I need to get this working or I fear I will be forced to develop in a windows environment :(

  Read the article

• Why would accessing photos over a network be a problem for Digikam?

  - by Shedeki

  Digikam has always worked nicely for me. I recently setup a Synology DiskStation (DS212+) and moved all my pictures to it, keeping them in an encrypted folder. I mount that folder using cifs, as some bug prevents eCryptfs and NFS from working together. This has led Digikam to being incredibly slow. Startup takes a very long time (several minutes for 41779 items, 123.8GB) but worse is how long it takes Digikam to write files. I like using Digikams import feature to copy new images from my camera to the hard drive because it checks for duplicates as well as creating a clear folder structure according to the dates the images were taken. Since I moved to using the network drive Digikam takes about 5 to 10 times as long to import photos than it did before. Saving modified or converted images takes equally long. What I am looking for is a way to help Digikam speed things up or an alternative piece of software (I have never liked Digikam being so very much KDEish…). There are just so many features that only Digikam seems to combine, e.g.: Batch processing. Respects existing folder structure. Does not mess up files for other applications. *.NEF support. Caches thumbnails in a clean way.

  Read the article

< Previous Page | 241 242 243 244 245 246 247 248 249 250 251 252  | Next Page >