Search Results

Search found 18488 results on 740 pages for 'android networking'.

Page 251/740 | < Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >

• How do I get a Belkin F5D8053 wireless adapter working?

  - by disassembler

  I've tried getting my Belkin N Wireless adapter to work on Ubuntu many times with no luck at all. Each time I seem to arrive at a dead end. After some thorough searching of UbuntuForums and WifiDocs I've gathered some information and narrowed the problem down to an issue with the rtl819xU driver. Here's some info that may help: $ sudo lshw -C network *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:22:75:38:52:ac capabilities: ethernet physical wireless configuration: broadcast=yes driver=rtl819xU multicast=yes wireless=802.11b/g/n $ sudo lsmod Module Size Used by vesafb 13449 1 snd_ice1724 106559 2 snd_ice17xx_ak4xxx 13163 1 snd_ice1724 snd_ac97_codec 105614 1 snd_ice1724 ac97_bus 12642 1 snd_ac97_codec snd_ak4xxx_adda 18436 2 snd_ice1724,snd_ice17xx_ak4xxx snd_ak4114 14326 1 snd_ice1724 snd_pt2258 12986 1 snd_ice1724 snd_i2c 13831 2 snd_ice1724,snd_pt2258 snd_ak4113 14307 1 snd_ice1724 snd_pcm 80244 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_ak4113 fglrx 2434640 121 snd_seq_midi 13132 0 snd_rawmidi 25269 2 snd_ice1724,snd_seq_midi binfmt_misc 13213 1 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event ppdev 12849 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq dcdbas 14054 0 r8192u_usb 297246 0 snd 55295 16 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_i2c,snd_ak4113,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd parport_pc 32111 1 snd_page_alloc 14073 1 snd_pcm shpchp 32345 0 lp 13349 0 parport 36746 3 ppdev,parport_pc,lp usbhid 41704 0 hid 77084 1 usbhid e100 40108 0 floppy 60032 0 $ sudo iwconfig wlan0 802.11b/g/n Mode:Managed Access Point: Not-Associated Bit Rate:1 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I'd like to know if 1) Is the driver is properly installed and recognized by Ubuntu? 2) What can I do to load the drivers properly and make use of the adapter? Thanks!

  Read the article

• Wireless not connecting on Ubuntu 13.10, Toshiba Satellite pro L 650

  - by user204842

  I have just installed Ubuntu 13.10 on my Toshiba Satellite Pro L650. After several reboots, installing/ uninstalling the broadcom driver I still can't connect. It detects the wi fi signals and the icon flashes as if it's trying to connect but never actually does. I'm really quite rubbish with code and stuff, but I really like Ubuntu as an OS and would really appreciate any suggestions anyone can offer! 02:00.0 Ethernet controller: Qualcomm Atheros AR8151 v1.0 Gigabit Ethernet (rev c0) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01)

  Read the article

• trouble detecing huawei EC156 in ubuntu 12.04

  - by naina

  the data card is never detected automatically...its detected only when i fire a lsusb. Later i give modeswitch commands etc etc...then the device works fine..i can easily use internet...but once i disconnect from the net, its impossible to reestablish the connection...to reconnect i have to type all the commands, starting with lsusb, in the terminal again..ie every time i want a connection i have to sit and type 5-6 commands in the terminal before i can get through. what can be done to get automatic net connection as soon as i plug in the data card...please help...

  Read the article

• Uploading or attaching files that located on a shared drive doesn't work?

  - by Alex

  I have this odd, quite minor, but annoying issue that I am quite perplexed about. Whenever I try to upload a file via my browser(let's say attach a file to an email in GMail), I click 'Browse' button and it opens standard file selection dialog, that doesn't show network drives. Further more if I try to drag a file from a network drive into GMail, it doesn't work either, it just doesn't let me do that. This issue has been around for quite sometime now, and I am just curious if this is something on my side or if it's a bug or a misconfiguration of some sort. FWIW, I am currently running 10.10, network drive is a samba share on NAS. This happens in FF and Chrome and this is only happens with Samba mounts. As a matter of fact, NFS volumes that are located on the same network operate perfectly fine.

  Read the article

• Ubuntu 12.04 host – Virtualbox 4.1.12 Guest=Windows 7 – Network will not connect

  - by user287529

  Ubuntu 12.04 host – Virtualbox 4.1.12 Guest=Windows 7 – Network will not connect. I'm using Ubuntu 12.04 on an Acer Aspire 5742-7645 laptop with 4GB memory, Intel Core i3 processor, Intel HD Graphics, DVD drive, 802.1 b/g/n, and 500 GB HD. I connect to my router via a wireless connection. I have installed Virutalbox 4.1.12 from the Ubuntu Software Center and installed Guest additions 4.1.12 in the Windows 7 guest session. I have Windows XP and Windows 7 installed as guests in Virtual box The network settings are different for XP and 7 – see below. Network Settings XP guest = Adapter 1: PCnet-FAST III (NAT) - Network works perfectly and has worked well for several years. Network Settings Win 7 = Adapter 1: Intel PRO/1000 MT Desktop (Bridged adapter, eth1) Promiscuous Mode = allow all Cable connected = checked When I originally installed Windows 7, I tried NAT and the guest network would not connect. Once I changed the setting to the above (Bridged) the Network worked perfectly. However, what I believe is after updates (not sure if it was an Ubuntu or Windows update) the guest network stopped working and I can not get it to connect. Interfaces file content auto lo iface lo inet loopback Ifconfig yields lou@lou-Aspire-5742:~$ ifconfig eth0 Link encap:Ethernet HWaddr 1c:75:08:09:f6:5c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 Link encap:Ethernet HWaddr 4c:0f:6e:7c:9f:01 inet addr:192.168.1.104 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::4e0f:6eff:fe7c:9f01/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18095 errors:2 dropped:0 overruns:0 frame:24344 TX packets:9281 errors:47 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5301926 (5.3 MB) TX bytes:1441885 (1.4 MB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3208 errors:0 dropped:0 overruns:0 frame:0 TX packets:3208 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:294088 (294.0 KB) TX bytes:294088 (294.0 KB) Ipconfig yields the following: Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::38ba:dbca:a21d:c3d1%13 Autoconfiguration IPv4 Address. . : 169.254.195.209 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Tunnel adapter isatap.{B292E440-679D-4FC5-8E34-77D6804669C8}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : I'm not sure what else to do. Can someone provide the troubleshooting steps to determine what the problem is and possible solution?

  Read the article

• How to resolve "Network host is busy; will retry in 30 seconds"?

  - by k0pernikus

  I have added a network printer, a Konica Minolta C253, via cups by its IP (http://10.0.0.42) under the http://localhost:631/ cups webfrontend on an Ubuntu 11.10 client. I used the documented KOC353U.ppd in the process. I was able to print exactly one page. Afterwards, all I get in the printer's status is the message: "Network host '10.0.0.42' is busy; will retry in 30 seconds". What is the problem here and how do I resolve it?

  Read the article

• Mobile Multiplayer games and coping with high latency

  - by spaceOwl

  I'm currently researching regarding a design for an online (realtime) mobile multiplayer game. As such, i'm taking into consideration that latencies (lag) is going to be high (perhaps higher than PC/consoles). I'd like to know if there are ways to overcome this or minimize the issues of high latency? The model i'll be using is peer-to-peer (using Photon cloud to broadcast messages to all other players). How do i deal with a scenario where a message about a local object's state at time t will only get to other players at *t + HUGE_LAG* ?

  Read the article

• Frequent disconnects using wlan AR9285

  - by John Neil

  I'm getting a large number of disconnects from my wireless when I switched to oneiric server (I did not see these happen with oneiric desktop) from my AR9285 wireless LAN device. Here is the syslog snippet: Oct 17 09:43:17 weather kernel: [ 1537.329138] wlan0: deauthenticated from 00:12:17:7a:8e:42 (Reason: 7) Oct 17 09:43:17 weather kernel: [ 1537.340409] cfg80211: All devices are disconnected, going to restore regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340423] cfg80211: Restoring regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340435] cfg80211: Calling CRDA to update world regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348571] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348581] cfg80211: World regulatory domain updated: Oct 17 09:43:17 weather kernel: [ 1537.348586] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Oct 17 09:43:17 weather kernel: [ 1537.348594] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348600] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348607] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348613] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348620] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Here is the relevant lspci output: # lspci | grep Atheros 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) I have done quite a bit of searching and saw discussions for previous versions of ubuntu that recommended installing the linux-backports-modules package. However, this does not appear to be available for oneiric (just the headers are listed as a package). Any advice on how to achieve a stable wireless connection for this server? It's location mitigates against using a wired connection.

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• IP/PORT forward requests to another server

  - by DT.DTDG

  I have the following listening PORT:IP set up on my UBuntu server. 12.345.67.890:3636 It receives requests perfectly, however, I would now like to forward any requests to that IP:PORT to another IP:PORT, i.e.: 09.876.54.321:3636 Essentially I want to do a request forward 12.345.67.890:3636 -> 09.876.54.321:3636. How can I go about it in Terminal and if I wanted to change it back how can I go about that too? Is there also a way to test that the data is forwarding and it is setup properly? Thanks! Edit: Can I just do as follows, just wondering how I would go about testing it and how I could disable it? sysctl net.ipv4.ip_forward=1 iptables -t nat -A PREROUTING -p tcp --dport 3636 -j DNAT --to-destination 09.876.54.321:3636 iptables -t nat -A POSTROUTING -j MASQUERADE

  Read the article

• Would a typical corporate firewall block a Java applet having the following behaviour

  - by auser

  I'm thinking of developing a proxy-like program to forward ports on a remote PC to a local PC (for example SSH). Assume that both local and remote PCs are running behind typical firewalls (i.e. consumer broadband router firewall, Windows firewall or corporate firewalls). The program will be a Java program which the user will run on both the remote and local PC. The remote client will periodically poll a central server to determine whether there are pending client connections. A session could be initiated as follows: The local client contacts the central server and request the current connection details for a specific remote client. The central server responds with the remote server's last received IP address and port. The next time the remote server polls the central server, the client's IP address and port are returned. The remote server initiates a connection to the local client using the IP address and port returned by the central server and listens for a response on a random port. The remote server will pass the value of the port it's listening on to central server. Goto 1, if client fails to connect to server. Would this work or will a typical firewall block the interactions.

  Read the article

• Wifi is connected but internet not working?

  - by Philip

  I have a lenovo x230 running ubuntu 12.04lts. I've been using it just fine for a while, but all of a sudden the internet's stopped working. It's connected to the router just fine (I can see the antenna bars saying it's connected) but when I try to go to a webpage, it's just loading forever. I've tried the fix listed here (http://ubuntuforums.org/showthread.php?t=1985079) but it hasn't done anything (the instructions are a little confusing though). I'm booting windows 7 right now and the internet works just fine when I'm on windows, so I know it must be a problem with ubuntu. I haven't touched any network settings before this problem happened, and I've been using it just fine for months, so I don't know why I'm getting this problem all of a sudden. Oh and I haven't updated anything in a few weeks (you know when the update manager pops up every so often listing all the things there's an update for) so I know it's not some update that broke it.

  Read the article

• How to connect MTS MBlaze on ubuntu 11.04

  - by murali_ma

  i have installed ubuntu 11.04 inside the windows xp. i have MTS Mblaze USB Modem. (my service provider is MTS MBlaze,india) i want to use Mblaze into ubuntu so that i did the following steps for make connecting the device. from the task bar->edit connections->mobile broadband->choose country->mts mblaze and ok i give username and password ([email protected] and password MTS. ok now i enable mobile broadband , MTS MBlaze connection1(connection name) from task bar. steps followed from "http://randomshandom.wordpress.com/2010/12/20/how-to-connect-mts-mblaze-device-in-ubuntu-10-10-11-04/#more-3" for the first time it successfully connected and browse the internet. after i restart the system i connect it. it does not connected. it shows Modem network disconnected. i accessed many times and delete the connection and recreated but i does not help me. if i try to connect device i think it the search the network, i saw the wave signal. img Image for showing problem:

  Read the article

• How to merge multiple internet connections into one

  - by Luis Alvarado

  My PC has 2 wired cards. Both gigalan. It also has 2 wireless cards. One broadcom with proprietary drivers and ralink with open software (which works much better than broadcom). My cellphone can share its connection wirelessly to my PC. But I also have a wired connection. So I have multiple connections that I can use to have internet. How can I merge 2 or more connections together and balance them to enjoy one unified internet experience that it is the sum of all internet connections connected to it. For example if I have an internet connection that offers 1024KB/Sec and another that offers 512KB/Sec and one small one that offers 128KB/Sec, after load balancing and merging all connections, I could download at a speed of 1664KB/Sec using all 3 internet connections as one for example. This question has always intrigued me.

  Read the article

• How should bots be recognised in a game?

  - by Bane

  I'm interested in how bots are usually written. Here's my situation: I plan to make an online 2D mecha game in HTML5, and the server-side will be done with node. It is intended to be multiplayer, but I also want to make bots in case there aren't enough players. How does my game logic see them, as players or as bots? Is there a standard by which I should make them? Also, any general tips and hints will be OK.

  Read the article

• Nouvelle page cours Android avec déjà 10 articles sur le développement mobile avec Android. Faites-n

  Bonjour à tous, Ce sujet est destiné à mieux connaître vos attentes et vos domaines préférés concernant Android. Pour faire bref : Quel tutoriel ou cours Android voudriez vous voir paraître prochainement sur DVP? N'hésitez pas à préciser : Pourquoi ce domaine vous interesse ? Pourquoi auriez vous besoin de ce cours/tutoriel ? Sous quelle forme le voudriez vous ? Cours théorique avec peu d'exemples? Tutoriel pratique avec de nombreux e...

  Read the article

• Set up Trendnet TEW-638APB Access point on Ubuntu 14.04

  - by Mr. Smileys

  I have a computer running Ubuntu 14.04, it has 2 Ethernet ports. I would like to set up this computer so that the internet comes in on one of the ports and is then shared through the other port with the Trendnet wireless access point that my other devices would connect to and use the internet. I have looked online for information on setting this up but have not been able to find anything. If someone could point me to a guide that would help me or just tell me how to do this in an answer I would really appreciate it. please help me to solve this problem

  Read the article

• Other people's files showing up in rhythmbox

  - by Avery Boyer

  I have my computer connected to a college network, and right now files that belong to other individuals on campus are showing up under Shared in rhythmbox. This is driving me up the wall, I absolutely despise the idea that files are being thrown around on the network and that other people's s*** is showing up on my computer, and that they may be able to see my files as well. This is a very, very serious problem as far as I am concerned and I want to know how I can ensure that I am sharing nothing with the network in the way of files on my computer and that no one else's files are showing up on my computer.

  Read the article

• Why dhclient is still running when I choose static IP?

  - by user276851

  I modify dhcp to static in /etc/network/interfaces (like below). # The primary network interface auto eth0 iface eth0 inet static netmask 255.255.0.0 address 10.10.130.128 gateway 10.10.1.1 Then restart the interface. $ sudo ifdown eth0; sudo ifup eth0 ... $ ifconfig eth0 Link encap:Ethernet inet addr:10.10.130.128 Bcast:10.10.255.255 Mask:255.255.0.0 So the new address kicks in. But DHCP is still there? $ ps aux | grep dhc root ... dhclient3 -e IF_METRIC=100 -pf /var/run/dhclient.eth0.pid -lf /var/lib/dhcp/dhclient.eth0.leases -1 eth0 Is that normal? If not, how to restart interface in static IP while stop DHCP at the same time? Thanks a lot.

  Read the article

• Google locking on Ubuntu

  - by user170534

  Problem I'm facing is that Google doesn't respond well timed to connection requests send from any browsers known to Linux. As far as I can tell, this was existent in Mint, which is Ubuntu based. I have no debug or guess about cause but I'm sure there are people with the same problem. ping of terminal is untouched but any other browser keeps unloaded, for example; google loads fine, I search for something. Then I decide to search for something else and ta daa: You gotta wait for 30 seconds for Google server to respond. I tried using google's public DNS without success. Flare the suggestions & ideas!?

  Read the article

• VM can't ping LAN name but sees it via nslookup

  - by amphibient

  I am trying to connect to a network resource from my 10.04.4 VM (VMware Fusion) but the destination is unreachable by name. What is weird is that the name is visible in DNS: >nslookup my.name Server: 123.45.67.89 Address: 123.45.67.89#53 Non-authoritative answer: Name: my.name Address: 10.20.30.40 I can reach it (via ping) by the IP address (10.20.30.40) but not the name and I thought that was weird because the DNS clearly resolves the name. What can I do to enable access to this resource via the name?

  Read the article

• Quickly and Python Twisted

  - by Aaron

  I am creating a Quickly application that makes use of Python Twisted. When the user launches a window, I want to start the Twisted server I wrote. However, when I do this, it freezes the GUI, because the reactor.run method is constantly running after it is started. I need a way to start the Twisted reactor in its own thread, so that the GUI will continue to operate while the reactor is running. I have read about using Twisted with pyGTK in the Twisted documentation, but I am not sure how I would accomplish this with a Quickly application. What is the best way to start my Twisted server when a window opens without freezing the GUI? Update: My if __name__ == '__main__' statement at the end of my dialog file is: print 'Preparing GLib' GLib.idle_add(before_running) print 'Staring Reactor' from twisted.internet import reactor reactor.run()` I have imported and installed twisted.gtk3reactor earlier on in the file. The before_running method contains dialog = ClientDialog() and dialog.show, as well as the rest of the code I want to run when the dialog opens.

  Read the article

• Ubuntu 11.10 is not detecting wired connection on Lenovo G580

  - by Dilip

  I am not able to see wired connection options in header menu. I can see wireless option but still It is not working. Could any one suggest what I am missing? Please find my ifconfig output: =================================== root@rails-dev:/home/rails_work/rdfnet# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:41944 errors:0 dropped:0 overruns:0 frame:0 TX packets:41944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4602835 (4.6 MB) TX bytes:4602835 (4.6 MB) ===================================

  Read the article

• Problems with microphone and network

  - by AnoonymoouS

  Hello... very good day everybody! I'm having some problems regarding the Ubuntu 12.4.01 LTS. For this reason, cordially i ask everyone's help. Such problems can be summed up in network (01) and audio (02)! 01) I can not set a DSL network settings in the "upper bar" (on side the clock). When i create the connection, the system says that the cables modem are disconnected! I can only use the internet if i set up a connection at terminal through the command "pppoeconf". Follows the print screen of what i mentioned above:. http://i.imgur.com/8nTrF.png Obs.: Note that even after the connection "created", it does not appear there! 02) The sound is reproduced; however, can not be captured! I can not make recordings, obviously i can't use the microphone. I believe that something is giving interference or the settings are wrong! Follows the video of what i mentioned above:. http://dl.dropbox.com/u/41085750/Projeto%20Padr%C3%A3o.mp4 Obs.: I'm listening to music, so that interference errors may appear in the video. By kindness; who can help me... help me! I sought help at various sites and forums but unfortunately, i did not get success. I wait anxiously for a direction. Regards, Anoonymoous.

  Read the article

• Ubuntu 12.10 - VirtualBox not sharing internet with guest system

  - by Fernando Briano

  I went from ArchLinux to Ubuntu on my dev box. I use VirtualBox to test web sites on Windows and IE. I have my Windows 7 VirtualBox image running on Ubuntu's VirtualBox. Back with ArchLinux, internet worked "out of the box" on the Windows boxes. I left the default options on the box's Network Options (NAT). The Windows machine shows as "connected to ethernet" but reports: The dns server isn't responding So I can't access Internet from there. I tried searching for Ubuntu's official docs but they seem pretty outdated. I tried using my old boxes from Arch (which boot normally but have no internet) and creating a new box from Ubuntu itself, but still get the same results. Update: I'm using VirtualBox 4.1.18 from Ubuntu's repository (apt-get install virtualbox).

  Read the article

< Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >