Search Results

Search found 18488 results on 740 pages for 'android networking'.

Page 247/740 | < Previous Page | 243 244 245 246 247 248 249 250 251 252 253 254 | Next Page >

Problems with wired ethernet connection Ubuntu 11.10

- by Andrew Fielden

After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

Read the article
Sharing SCTP connection with multiple threads

- by poly

I have an application that needs to run in SCTP environment, I have a question in sharing the connection among multiple threads for packet receiving only, I've tried with the sctp_sendmsg and it worked without even locking the threads (is that been taking care of by the OS, in other words, is it thread safe to do that). I've tested many cases with the send and I can't see them out of sync. Anyway, back to the receiving, is it possible to create multiple threads and send each thread the sctp descriptor to start receiving messages? Do I need a lock here or is it ok without lock? I'm using C in linux.

Read the article
Yoga Pro 2 Wi-Fi not working

- by user293004

I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

Read the article
Moving AI in a multiplayer game

- by Smallbro

I've been programming a multiplayer game and its coming together very nicely. It uses both TCP and UDP (UDP for movement and TCP for just about everything else). What I was wondering was how I would go about sending multiple moving AI without much lag. At first I used TCP for everything and it was very slow when people moved. I'm currently using a butchered version of this http://corvstudios.com/tutorials/udpMultiplayer.php for my movement system and I'm wondering what the best method of sending AI movements is. By movements I mean the AI chooses left/right/up/down and the player can see this happening. Thanks.

Read the article
Reconstruct a file from a TCP stream

- by Abhishek Chanda

I have a client and a server and a third box which sees all packets from the server to the client (but not the other way around). Now when the client requests a file from the server (over HTTP), the third box sees the response. I am trying to reconstruct the file there. I am using libpcap to capture TCP datagrams and trying to reconstruct the file there. Here is what I did Listen for packets on an interface Group all packets which have the same ACK number Sort the group based on SEQ number Extract data from each packet and combine them and write to the disk The problem is, the file thus generated is not exactly the same as the original file. Does everything sound correct here? Some more details: I am using C++ The packet data is being stored as std::vector<char> I did change the byte order while reading the ack number and seq number from the packet using ntohl I am not sure if I need to change the byte order for the data as well. I tried to reverse the data from each packet before combining them, even that did not work. Is there something I am missing?

Read the article
Create personal wireless network on laptop

- by TechGuru

I have a WiFi Network, now I have connected my laptop to the WiFi Network. And it is working fine I'm able to access the internet via WiFi. But I want to create other network on my laptop so that I can connect my mobile phone to the my laptop network. Means, my laptop is already connected to WiFi network (xyz). Now I want to create one wireless network on my laptop. So that I can connect my mobile phone to laptop network and access the internet on mobile. But I don't want to lost my `laptop and WiFi connection that is already connected. I tried to create the wireless network on my laptop, but when I created my personal wireless network I lost my wifi-laptop connection. I don't know it is possible or not.

Read the article
How to connect to a serverside process on Ubuntu running in a VM?

- by Jenko

I am running Ubuntu 11.10 in VirtualBox, on Windows 7. I'm trying to setup a serverside process like Apache on it. How do I configure VirtualBox to allow access to the Ubuntu server process from other computers on the network? I can access the internet from Ubuntu. The Windows 7 computer is on a WiFi network using DHCP. The WiFi network has a dynamic IP with the network provider. This is my current configuration:

Read the article
Can't connect to or see my wifi ssid

- by ant

Today I installed ubuntu 12.04 on my laptop. I am unable to see my home SSID or even connect to it. I've tried to connect as a hidden SSID but I always get prompted for authorization although my key is correct. I'm in in Europe but my laptop is from US. I'm not sure if that is relevant. I've read around this site and saw something that has to do with setting the channel above 11. I'm not sure I did that correctly I did this : How to use Wi-Fi channels above 11? Did't help. I'm able to connect with cable but not via wifi either windows or linux. Other devices in my home can connect without any issues, even the kindle. Here is the screenshot from my router : Here is some additional info : lspci | grep -i network 08:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) lspci -nnk | grep -A2 0280 08:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) Subsystem: Hewlett-Packard Company U98Z062.10 802.11bgn Wireless Half-size Mini PCIe Card [103c:303f] Kernel driver in use: ath9k m-tool NetworkManager Tool State: connected (global) Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: disconnected Default: no HW Address: 90:4C:E5:38:79:0D Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes I'm not sure what to do next. Any suggestions?

Read the article
wifi not working hp dv4

- by Blaze

i get this output for sudo lshw -C network : *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 06 serial: 3c:4a:92:cd:63:98 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network DISABLED description: Wireless interface product: RT5390 [802.11 b/g/n 1T1R G-band PCI Express Single Chip] vendor: Ralink corp. physical id: 0 bus info: pci@0000:0a:00.0 logical name: wlan0 version: 00 serial: 90:00:4e:82:3c:5b width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.0.0-17-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c2500000-c250ffff i cant enable the wifi using the fn+f12 key.. its just stuck. In windows 7 it gets enabled when i press the same keys. but this happens after it gets booted up... i just want to use the wifi in anyway possible. can anybody help?

Read the article
How to run a local and external website on same computer with 2 NIC's, 2 Routers and 3 seperate networks?

- by CandN

Hello and hopefully I can get some answers to my question, though I think I'm making it more complicated for myself than it has to be. My business is a used auto dealership, and I'm in the process of connecting it to the world - via ethernet from the business server [running Xubuntu] to the ISP's ethernet router/modem, so that I can host our own website (no more than 5-10 people probably visiting at any time - mainly paying their bill), as well as set up a web based internal-intranet site - via DD-WRT Router on the 2nd NIC on the business server - that'll be accessed over Wifi from employees personal devices. On the other end of this is trying to offer free wifi to customers that is completely seperate of the 2 mentioned above networks. Quick Rundown: 1. Web Site for Customers to access. I'm going to use no-ip.org for DNS for the moment being, so I'll have a site that customers can access from anywhere in the world at "mybiz.no-ip.org". This will be forwarded to NIC #1 on the server, possibly at an address like "108.69.." as its being provided an IP from the ISP's modem/router, that is from Time Warner, and they allow NO! configuration options. Web Site for employees to access. I'm trying not to use the server too much as a desktop, only for critical situations, so having a backend thats seperate from the front-facing website is critical. This will be the DD-WRT router hardwired into NIC #2 on the server. This WiFi will be password accessible. Public WiFi for customers. The DD-WRT can seperate networks if I'm correct, I just can't seem to understand how to seperate the 2 and still have internet access on both. I've done it before, but the "Public" wifi (with no password set to connect) kept dropping the connection like a problem was happening that I couldn't figure out. So if I could do a little drawing, this is how it would/should possibly look. ISP -- [Sends Public Facing IP of 108.69.*.1/8] -- ISP Modem Router ISP Modem Router (Ethernet Only) -- [Gives Private IP 108.69.*.2] -- Server NIC #1 Server NIC #1 -- [Gives Private IP 108.69.*.3] -- DD-WRT Router DD-WRT Router -- [DHCP Enabled Giving IP's 172.16.0.0/16] -- Employees Network | | --------- [DHCP Enabled Giving IP's 192.168.1.0/24] -- Public WIFI Hope it's not too confusing, but it anyone could give me some good direct tutorials on how to accomplish this, or if YOU know, then it'll be alot of help. Thanks to all in advance. Need anything else to be explained? Don't hesitate to ask! *Using The LAMP stack with Webmin/VirtualMin -Customer site is located in /var/www2/ -Private Employees site is located in /var/www/ Using no-ip.org's dynamic client updater

Read the article
RPC protocols comparison

- by Ricardo

I have to select a protocol/technology to use for communicating a client-server architecture, with support both for Python and C. The main requirements are: Symmetrical communication in between ends: clients establish a connection and servers can send data back to clients through the same connection. Avoid excessive overhead by using HTTP or a big stack (if possible, TCP direct communication). TLS/SSL support for secure communications. Ease of implementation. For that, I evaluated the following protocols/communications technologies. Is the information on this table accurate and correct? (*1) TLS support for RPyC is based in a no-longer supported Python library.

Read the article
Problems connecting to eduroam wifi - ubuntu touch

- by Fiona Cox

I am trying to connect to our university's eduroam wi-fi network with my Nexus 4 running Ubuntu touch (utopic latest build), but can't get past the first stage. I wonder if anyone can help please? I am following these instructions (which worked for my iPhone): http://www.st-andrews.ac.uk/itsupport/mobile/eduroam/ But when I go to the bandit.st-andrews.ac.uk/connect page then follow the link to 'eduroam setup' I get the error message: Authorization Required This server could not verify that you are authorised to access the document requested. Either you supplied the wrong credentials (e.g., bad password), or your browser doesn't understand how to supply the credentials required. Apache/2.2.16 (Debian) Server at bandit.st-andrews.ac.uk Port 443 (Clearly it's the latter option (browser) as I haven't been asked for my credentials yet.) Is there a way round this, or am I just not going to be able to connect until further down the Ubuntu touch development road... Thanks!

Read the article
Ping Access to a Nested VM !! Plz Help

- by Shivaramakrishnan

I have a problem in communication between the host and the nested VM.This is my layout. I have installed KVM on host machine having a single nic interface (public ip) running Ubuntu.On top of this,I have VM running Ubuntu.I have installed KVM in this VM too.I then have a VM inside this running a web server. I am able to ping the host from this web server VM and ssh into it.But from host to VM ,ping is being unsuccessful. The VM (named L1hyp) on host was created using libvirt-manager and has IP of 192.168.122.8. The vswitch interface created at host is in default config (NAT-ed). Its IP is 192.168.122.1. Now this VM is also having a vswitch interface which is in default config (NAT-ed).Its IP is 192.168.100.1. The Web server VM is created on top of this L1hyp VM, is having an IP of 192.168.100.186. The Webserver VM uses 192.168.100.1 as its default gw. The L1hyp uses 192.168.122.1 as its default gw. From Host: ping 192.168.122.8 - SUCCEEDS ping 192.168.122.1 - SUCCEEDS ping 192.168.100.1 - SUCCEEDS ping 192.168.100.186 - FAILS Comes up with Destination Host Unreachable From 192.168.122.1. But there is route to 192.168.100.0/24 subnet from host.Ping to 192.168.100.1 succeeds. From Webserver VM: ping 192.168.100.1 - SUCCEEDS ping 192.168.122.1 - SUCCEEDS SSH from web server VM to host succeeds. Can anyone help me out what needs to be modified to have two way communication between the host and Webserver VM at the earliest? I am pondering over this problem for over a week now.

Read the article
How do I get a Qualcomm Atheros Killer E2200 gigabit ethernet card working on a MSI Z87-GD65?

- by Travis Allen

So I literally just built my first computer from scratch and I can't get the network card to work as I've gathered it requires getting some drivers somehow.. Motherboard : MSI Z87-GD65 CPU : Intel Haswell i7 Ubuntu Ver : 12.04 Using the on-board network port Please help I'm about to start crying into my keyboard over this (not really). Any info would be greatly appreciated, also please be very specific as to what I have to do as I have not used Ubuntu very much so talk to me like a child, I won't take offence. Also I've already tried following the instructions here : How do I get a Qualcomm Atheros Killer E2200 gigabit ethernet card working? I don't know if I'm just retarded or am missing something

Read the article
Is it possible to set a VPN through Tor? and have functionality for Software Updates?

- by moazhmi

Gday, I have been trying to do a software update on Trusty both on terminal and software update app but that hasnt been successful, apparently my ISP has a broken transparent proxy. moazhmi@moazhmi-K52F:~$ wget -S http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease --2014-06-04 17:34:52-- http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease Resolving extras.ubuntu.com (extras.ubuntu.com)... 91.189.92.152 Connecting to extras.ubuntu.com (extras.ubuntu.com)|91.189.92.152|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 200 OK Content-Type: text/html; charset=UTF-8 Content-Length: 213 Date: Wed, 04 Jun 2014 14:34:52 GMT Server: Apache/2.2.22 (Ubuntu) Connection: Keep-Alive Vary: Accept-Encoding Length: 213 [text/html] Saving to: ‘InRelease’ 100%[======================================>] 213 --.-K/s in 0s 2014-06-04 17:34:52 (22.1 MB/s) - ‘InRelease’ saved [213/213] I was advised to refer back to the ISP with a complaint but that has returned with peanuts. My Question is - Is it possible to set a VPN through TOR , i.e whereas I can run software updates through terminals or the app . the browsing is out of question here as I need to update which I am not able to do / only on 12.04.

Read the article
Ubuntu connects to wireless but doesn't work!

- by UbuntuUser990

I just installed Ubuntu 14.04 LTS on my laptop, it connects to my wireless network and shows that it is connected, but when I try to load a webpage or do anything like download Steam for Dota 2, it doesn't work. When I try to connect my Facebook account to Ubuntu, it doesn't work. I want to be able to use Ubuntu with working internet access. What do I do?. ifconfig this shows up eth0 Link encap:Ethernet HWaddr 88:ae:1d:60:56:eb inet addr:192.168.1.13 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1856 (1.8 KB) TX bytes:1856 (1.8 KB) When I type ping askubuntu.com this shows up ping: unknown host askubuntu.com

Read the article
Can't connect to hidden network with BCM4313

- by poomerang

The wireless works fine with all the other wi-fi nets I have tried, the only problem is with this hidden network. I should add it's the only hidden network I've tried, so I am not sure if the problem is it being hidden or somethings else, but I've checked the settings of NetworkManager against another Ubuntu system (which can connect) and they appear to be the same, passphrase included. The network is using WPA2 Personal with AES encryption, I don't know how to check this setting but I believe it's the usual for WPA2, and therefore usually not a problem. Also, I can connect through ethernet, which should exclude any blacklisting of my device, I believe. I usually use brcmsmac drivers, I've tried also STA but the result is the same. I've also tried the suggestion from Unable to connect to hidden SSID with no luck output of lspci -v is 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Askey Computer Corp. Device 7175 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d4000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

Read the article
MAAS. Adding nodes

- by 2bus.erkanat

Can anybody help me with MAAS installation? I installed it on 1 of my computers, configured DHCP server and now 3 PCs are in their own private network. I tried to add node via PXE image, but "Can not apply stage final, no datasource found! Likely bad things to come!" error comes after giving me option to log in. Then I tried to add node via web interface, but after adding it node's status is always "commisioning". So what should I do know? Any help is appreciated. Thank you P.S. English is not my native language, sorry for any type of errors.

Read the article
How to share a folder without any issues when we have >20 machines in LAN ?

- by Gaurang Agrawal

Till date I have been sharing files through workgroup , using samba but I presume that this is not the right way as I had been facing so many issues with one or another computer . Machines are having same workgroup but even then problems are there . What will be the best way to handle this kind of issue ? PS : I am helping a school migrate from Windows to Ubuntu 12.04 LTS ( Teachers collaborate by working on different files saved in a shared folder in one of the computer )

Read the article
No Wireless In Ubuntu 13.10

- by viktorhubinette

When I upgraded to Ubuntu 13.10, I can't connect to wireless. The only thing I can connect to is ethernet, so please help me, What should I do? Here is the output of the lspci -nnk | grep -i net -A2 00:19.0 ethernet controller [0200]:intel corporation 82579V Gigabit network connection [8086:1503] (rev 04) subsystem: acer incorporated [ALI Device] [1025:8000] Kernel driver in use : e100e output of lsusb: Bus 002 Device 003: ID 046d:c31c Logitech, Inc. Keyboard K120 for Business Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:0152 Realtek Semiconductor Corp. Mass Storage Device Bus 001 Device 040: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 004: ID 0bda:8178 Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter Bus 003 Device 003: ID 045e:070f Microsoft Corp. Bus 003 Device 002: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Read the article
Simple NAS setup for Ubuntu

- by Sean Houlihane

So, I want to connect my shiny new NAS (QNAP TS-210p II) to my Ubuntu 11.10 box. I have a 2nd Ubuntu machine, but I don't use that enough to be too worried about it. Use is ideally to offload all storage except for system (which can then run off a 30GB flash drive). The main machine also runs Myth front/backends. Both are on a wired network currently. I have got a basic setup working, mounted over NFS, but have some issues, and whenever I look for answers, I seem to get unto the UbuntuServer domain, with what seems like more detail than I want in an answer. Questions I have identified so far: 1) Sharing UIDs to get file permissions correct. LDAP or something else? What is necessary to make this work? 2) Mounting an NFS device reliably. Do I just add it in fstab or is some sort of auto-mount advisable? Its a wired network, but I shouldn't need to worry about reboot after power-outages and sequencing...

Read the article
Trying to configure samba share with office server

- by tomphelps

Hi, i'm trying to set up fstab to automatically connect to my office shared server. I'm undoubtedly doing something silly here as the username and password and server name work fine in the first code snippet below, just not the second - any help would be appreciated! The following command works as expected... tom@tom-desktop: sudo /usr/bin/smbclient -L Server.local -Uguest Enter guest's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.10] Sharename Type Comment --------- ---- ------- Lacie Disk Disk macosx Server Disk macosx IPC$ IPC IPC Service (Server) ADMIN$ IPC IPC Service (Server) Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.10] Server Comment --------- ------- ACER-9D60040D10 SERVER Server Workgroup Master --------- ------- WORKGROUP ACER-9D60040D10 But when i add the following line to /etc/fstab, i get this error: cifs_mount failed w/return code = -22 //Server.local/Server /media/maguires cifs username=guest,password=password 0 0

Read the article
Physics not synchronizing correctly over the network when using Bullet

- by Lucas

I'm trying to implement a client/server physics system using Bullet however I'm having problems getting things to sync up. I've implemented a custom motion state which reads and write the transform from my game objects and it works locally but I've tried two different approaches for networked games: Dynamic objects on the client that are also on the server (eg not random debris and other unimportant stuff) are made kinematic. This works correctly but the objects don't move very smoothly Objects are dynamic on both but after each message from the server that the object has moved I set the linear and angular velocity to the values from the server and call btRigidBody::proceedToTransform with the transform on the server. I also call btCollisionObject::activate(true); to force the object to update. My intent with method 2 was to basically do method 1 but hijacking Bullet to do a poor-man's prediction instead of doing my own to smooth out method 1, but this doesn't seem to work (for reasons that are not 100% clear to me even stepping through Bullet) and the objects sometimes end up in different places. Am I heading in the right direction? Bullet seems to have it's own interpolation code built-in. Can that help me make method 1 work better? Or is my method 2 code not working because I am accidentally stomping that?

Read the article
How to properly do weapon cool-down reload timer in multi-player laggy environment?

- by John Murdoch

I want to handle weapon cool-down timers in a fair and predictable way on both client on server. Situation: Multiple clients connected to server, which is doing hit detection / physics Clients have different latency for their connections to server ranging from 50ms to 500ms. They want to shoot weapons with fairly long reload/cool-down times (assume exactly 10 seconds) It is important that they get to shoot these weapons close to the cool-down time, as if some clients manage to shoot sooner than others (either because they are "early" or the others are "late") they gain a significant advantage. I need to show time remaining for reload on player's screen Clients can have clocks which are flat-out wrong (bad timezones, etc.) What I'm currently doing to deal with latency: Client collects server side state in a history, tagged with server timestamps Client assesses his time difference with server time: behindServerTimeNs = (behindServerTimeNs + (System.nanoTime() - receivedState.getServerTimeNs())) / 2 Client renders all state received from server 200 ms behind from his current time, adjusted by what he believes his time difference with server time is (whether due to wrong clocks, or lag). If he has server states on both sides of that calculated time, he (mostly LERP) interpolates between them, if not then he (LERP) extrapolates. No other client-side prediction of movement, e.g., to make his vehicle seem more responsive is done so far, but maybe will be added later So how do I properly add weapon reload timers? My first idea would be for the server to send each player the time when his reload will be done with each world state update, the client then adjusts it for the clock difference and thus can estimate when the reload will be finished in client-time (perhaps considering also for latency that the shoot message from client to server will take as well?), and if the user mashes the "shoot" button after (or perhaps even slightly before?) that time, send the shoot event. The server would get the shoot event and consider the time shot was made as the server time when it was received. It would then discard it if it is nowhere near reload time, execute it immediately if it is past reload time, and hold it for a few physics cycles until reload is done in case if it was received a bit early. It does all seem a bit convoluted, and I'm wondering whether it will work (e.g., whether it won't be the case that players with lower ping get better reload rates), and whether there are more elegant solutions to this problem.

Read the article
MAAS and Openstack Network

- by user281985

Trying to figure out the best way for openstack and MASS networks to co-exist. Assuming MAAS used 10.0.0.0/24 for provisioning of various openstack nodes, once openstack, with quantum, is deployed should 10.0.0.0 be used as management network, external network, both or discarded? Reason for the question being that I ran a deployment where openstack used 10.0.0.0 as its management network, MAAS dhcp and dns were active; however, I could only access VMs through namespace and was not able to utilize MAAS's dhcp to assign floating IP. (VMs network was through an internal bridge 10.10.10.10, and external bridge was using the same interface as MAAS.) Any thoughts or ideas are appreciated.

Read the article

< Previous Page | 243 244 245 246 247 248 249 250 251 252 253 254 | Next Page >