Search Results

Search found 18488 results on 740 pages for 'android networking'.

Page 248/740 | < Previous Page | 244 245 246 247 248 249 250 251 252 253 254 255  | Next Page >

  • Slow wifi with D-link DWA-160 A2

    - by Tommy Brunn
    I recently bought a USB wifi adapter for my new desktop computer. It's a D-link DWA-160 A2. From the start it didn't want to work at all, but after unplugging and then plugging it back in, it seems to work. However, my browsing is painfully slow. NetworkManager reports the connection to be at around 78-85% signal strength, which seems perfectly acceptable. Is there anything I can do to make it faster? I'm dual booting with Windows 7, where it seems to work fine, so I'm guessing that the problem occurs because of crappy drivers.

    Read the article

  • MAAS. Adding nodes

    - by 2bus.erkanat
    Can anybody help me with MAAS installation? I installed it on 1 of my computers, configured DHCP server and now 3 PCs are in their own private network. I tried to add node via PXE image, but "Can not apply stage final, no datasource found! Likely bad things to come!" error comes after giving me option to log in. Then I tried to add node via web interface, but after adding it node's status is always "commisioning". So what should I do know? Any help is appreciated. Thank you P.S. English is not my native language, sorry for any type of errors.

    Read the article

  • Network does not connect at boot

    - by Daniel Svozil
    I am on Ubuntu 12.04, fresh install. When I boot a machine, the boot screen says Connecting to network, later it is changed to something like Did not connect, trying for another 60s. However, the network does not connect at the boot. But I can then log in without a network connection, and if I start a network manager service manually from the terminal (sudo service network-manager start), the network is connected without any problems. Please, does anybody know where the problem could be? I don't want to wait more than two minutes every computer restart :-). I am new to Ubuntu (and also to upstart) so I am a bit lost. There is no /var/log/messages, in dmesg I found this record, though it may not be related: init: network-interface (eth1) pre-start process (492) terminated with status 1 init: network-interface (eth1) post-stop process (548) terminated with status 1 Thanks Daniel

    Read the article

  • Is it possible to set a VPN through Tor? and have functionality for Software Updates?

    - by moazhmi
    Gday, I have been trying to do a software update on Trusty both on terminal and software update app but that hasnt been successful, apparently my ISP has a broken transparent proxy. moazhmi@moazhmi-K52F:~$ wget -S http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease --2014-06-04 17:34:52-- http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease Resolving extras.ubuntu.com (extras.ubuntu.com)... 91.189.92.152 Connecting to extras.ubuntu.com (extras.ubuntu.com)|91.189.92.152|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 200 OK Content-Type: text/html; charset=UTF-8 Content-Length: 213 Date: Wed, 04 Jun 2014 14:34:52 GMT Server: Apache/2.2.22 (Ubuntu) Connection: Keep-Alive Vary: Accept-Encoding Length: 213 [text/html] Saving to: ‘InRelease’ 100%[======================================>] 213 --.-K/s in 0s 2014-06-04 17:34:52 (22.1 MB/s) - ‘InRelease’ saved [213/213] I was advised to refer back to the ISP with a complaint but that has returned with peanuts. My Question is - Is it possible to set a VPN through TOR , i.e whereas I can run software updates through terminals or the app . the browsing is out of question here as I need to update which I am not able to do / only on 12.04.

    Read the article

  • Ubuntu connects to wireless but doesn't work!

    - by UbuntuUser990
    I just installed Ubuntu 14.04 LTS on my laptop, it connects to my wireless network and shows that it is connected, but when I try to load a webpage or do anything like download Steam for Dota 2, it doesn't work. When I try to connect my Facebook account to Ubuntu, it doesn't work. I want to be able to use Ubuntu with working internet access. What do I do?. ifconfig this shows up eth0 Link encap:Ethernet HWaddr 88:ae:1d:60:56:eb inet addr:192.168.1.13 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1856 (1.8 KB) TX bytes:1856 (1.8 KB) When I type ping askubuntu.com this shows up ping: unknown host askubuntu.com

    Read the article

  • Changing internal home network ip address for connected devices

    - by oshirowanen
    I have a few computers at home. For each of the computers, I can see the internal home network ip address on any given device by typing in ifconfig in the terminal. If the device is connected to the home network via ethernet connection or via the built-in wireless connections in laptops, the internal ip address for each of the devices seems to be 192.168.0.X. However, when I connect one of the devices using an external usb modem wireless adapter, which connects to the home network through wireless, when I check the ip address via ifconfig, for some reason it gets assigned 192.168.42.X instead. Why are the ethernet and build in wireless connections getting 192.168.0.X, but the external usb wireless adapter gets 192.168.42.X? Most importantly, is it possible to force it to get an internal ip address of 192.168.0.X?

    Read the article

  • Can only connect to file server on second attempt

    - by Ross Fleming
    I have a FreeNas file server on my local network and I usually connect to it from Windows and Ubuntu computers. Ever since I have upgraded from Ubuntu 12.04 to 12.10 Ubuntu will only connect after a second attempt. By which I mean, I will browse to it via the file manager and once I click on the link in "Bookmarks" it complains that it could not connect. If I then try again it connects successfully and will keep up it's connection until the laptop is suspended or looses connection to the LAN for whatever reason. This isn't much of a problem as I don't mind having to click twice but my real problem is that this means that my scheduled backup will complain that it cannot connect to the storage device if it has not already been accessed during the current session. If there is some way to either stop the issue all together or to force the backup tool (default) to immediately have a second attempt at connecting.

    Read the article

  • Internet connection randomly drops out

    - by Dr_Bunsen
    Since a week or 2, I have this random network failures. No error pops up, the system says it's still connected to the internet(wifi and wired). The problem is, I can't connect to anything, even a ping google.com gives no feedback. And after many network-manager resets it will work again, for just a minute, and drop out again. I noticed that the /etc/resolv.conf contains this line: nameserver 127.0.0.1 I left out the "Do not edit" stuff, and after it worked for a second, this line is added: search lan When I change the nameserver to 8.8.8.8, I am still able to connect to anywhere. Does anyone got a clue what is happening here? I will provide any information asked. Thanks in advance p.s. I run Ubuntu 13.04 since lastnight(24-06-2013)

    Read the article

  • How do I find out which process is eating up my bandwidth?

    - by Bruce Connor
    I think I'm being the victim of a bug here. Sometimes while I'm working (I still don't know why), my network traffic goes up to 200 KB/s and stays that way, even tough I'm not doing anything internet-related. This sometimes happens to me with the CPU usage. When it does, I just run a top command to find out which process is responsible and then kill it. Problem is: I have no way of knowing which process is responsible for my high network usage. Both the resource monitor and the top command only tell me my total network usage, neither of them tells me process specific network info. Is there another command I can use to find out which process is getting out of hand? I've already tried killing all the obvious ones (firefox, update-manager, pidgin, etc) with no luck. So far, restarting the machine is the only way I found of getting rid of the issue. EDIT: (just to be clear) I've found questions here about monitoring total bandwidth usage, but, as I mentioned, that's not what I need. UPDATE: The command iftop gives results that disagree entirely with the information reported by System Monitor. While the latter claims there's high network traffic, the former claims there's barely 1 KB/s. Thanks

    Read the article

  • Google I/O 2012 - New YouTube Android Player Tools

    Google I/O 2012 - New YouTube Android Player Tools Ross McIlroy, Anton Hansson If you are building Android smartphone, tablet or Google TV applications and want to incorporate high-quality YouTube video playback in your product this session will rock your world. For all I/O 2012 sessions, go to developers.google.com From: GoogleDevelopers Views: 1719 24 ratings Time: 51:10 More in Science & Technology

    Read the article

  • Can't connect to hidden network with BCM4313

    - by poomerang
    The wireless works fine with all the other wi-fi nets I have tried, the only problem is with this hidden network. I should add it's the only hidden network I've tried, so I am not sure if the problem is it being hidden or somethings else, but I've checked the settings of NetworkManager against another Ubuntu system (which can connect) and they appear to be the same, passphrase included. The network is using WPA2 Personal with AES encryption, I don't know how to check this setting but I believe it's the usual for WPA2, and therefore usually not a problem. Also, I can connect through ethernet, which should exclude any blacklisting of my device, I believe. I usually use brcmsmac drivers, I've tried also STA but the result is the same. I've also tried the suggestion from Unable to connect to hidden SSID with no luck output of lspci -v is 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Askey Computer Corp. Device 7175 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d4000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

    Read the article

  • Lost network interface after mac change

    - by Arturo Grc
    I'm using Ubuntu server 12.04 inside Virtualbox and everything was working as expected, but since I changed the mac address in Virtualbox network settings the network interface is not being recognized on Ubuntu. I don't remember the old mac address and everytime Ubuntu starts shows waiting for network configuration when I use ifconfig only appears lo (loopback device) and eth0 is lost, how can I fix this problem?

    Read the article

  • Which game logic should run when doing prediction for PNP state updates

    - by spaceOwl
    We are writing a multiplayer game, where each game client (player) is responsible for sending state updates regarding its "owned" objects to other players. Each message that arrives to other (remote) clients is processed as such: Figure out when the message was sent. Create a diff between NOW and that time. Run game specific logic to bring the received state to "current" time. I am wondering which sort of logic should execute as part of step #3 ? Our game is composed of a physical update (position, speed, acceleration, etc) and many other components that can update an object's state and occur regularly (locally). There's a trade off here - Getting the new state quickly or remaining "faithful" to the true state representation and executing the whole thing to predict the "true" state when receiving state updates from remote clients. Which one is recommended to be used? and why?

    Read the article

  • How to properly do weapon cool-down reload timer in multi-player laggy environment?

    - by John Murdoch
    I want to handle weapon cool-down timers in a fair and predictable way on both client on server. Situation: Multiple clients connected to server, which is doing hit detection / physics Clients have different latency for their connections to server ranging from 50ms to 500ms. They want to shoot weapons with fairly long reload/cool-down times (assume exactly 10 seconds) It is important that they get to shoot these weapons close to the cool-down time, as if some clients manage to shoot sooner than others (either because they are "early" or the others are "late") they gain a significant advantage. I need to show time remaining for reload on player's screen Clients can have clocks which are flat-out wrong (bad timezones, etc.) What I'm currently doing to deal with latency: Client collects server side state in a history, tagged with server timestamps Client assesses his time difference with server time: behindServerTimeNs = (behindServerTimeNs + (System.nanoTime() - receivedState.getServerTimeNs())) / 2 Client renders all state received from server 200 ms behind from his current time, adjusted by what he believes his time difference with server time is (whether due to wrong clocks, or lag). If he has server states on both sides of that calculated time, he (mostly LERP) interpolates between them, if not then he (LERP) extrapolates. No other client-side prediction of movement, e.g., to make his vehicle seem more responsive is done so far, but maybe will be added later So how do I properly add weapon reload timers? My first idea would be for the server to send each player the time when his reload will be done with each world state update, the client then adjusts it for the clock difference and thus can estimate when the reload will be finished in client-time (perhaps considering also for latency that the shoot message from client to server will take as well?), and if the user mashes the "shoot" button after (or perhaps even slightly before?) that time, send the shoot event. The server would get the shoot event and consider the time shot was made as the server time when it was received. It would then discard it if it is nowhere near reload time, execute it immediately if it is past reload time, and hold it for a few physics cycles until reload is done in case if it was received a bit early. It does all seem a bit convoluted, and I'm wondering whether it will work (e.g., whether it won't be the case that players with lower ping get better reload rates), and whether there are more elegant solutions to this problem.

    Read the article

  • ifconfig not showing all IPs bound to the machine

    - by pankaj sharma
    I have configured multiple IP addresses on a ubuntu box, but when I run ifconfig it shows just one of them. I am able, however, to ping all other adresses assigned to this machine. /etc/network/interface contents: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.202.11 netmask 255.255.255.0 network 192.168.202.0 broadcast 192.168.202.255 gateway 192.168.202.1 # dns-* options are implemented by the resolvconf package, if installed dns-search idil.dz1.da auto eth0:1 iface eth0:1 inet static address 192.168.202.12 netmask 255.255.255.0 auto eth0:2 iface eth0:2 inet static address 192.168.202.13 netmask 255.255.255.0 auto eth0:3 iface eth0:3 inet static address 192.168.202.14 netmask 255.255.255.0 auto eth0:4 iface eth0:4 inet static address 192.168.202.15 netmask 255.255.255.0 auto eth0:5 iface eth0:5 inet static address 192.168.202.16 netmask 255.255.255.0 but the output of the ifconfig is only: 192.168.202.11

    Read the article

  • Wireless is disabled by hardware switch on Dell Inspiron 1750

    - by lowerkey
    I have a problem where Ubuntu (12.04) says there is a wireless network card, but it is disabled by a hardware switch. How do I turn it on? I checked the BIOS, and the wireless card is enabled there. Fn + F2 was also no success. The results of rfkill list: 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes sudo rfkill unblock wifi did nothing to the Wireless Status.

    Read the article

  • Ubuntu 12.04 + Wifi not working

    - by user171154
    i'm having problems connecting over wireless. At the moment, I'm using wicd. It seems to get stuck on "Verifying AP association...". Without wicd I can get the connection up and ping the Net - but if I take eth0 down (ifconfig eth0 down), my wireless goes away too (same result if I unplug the wire instead). wicd is the only way I can bring eth0 back (which is the main reason I'm using it) - ifconfig eth0 and/or ifup eth0 do not re-enable the connection (I just discovered it leaves out the gateway. Adding the gateway back in re-enables the connection including wifi; I didn't want to delete the info about wicd above in case it gives someone an idea.) Doing it manually, despite the errors (which it would be nice to also resolve) - allows me to ping the outside world: ifup wlan0 ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument ssh stop/waiting ssh start/running, process 17336 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=43 time=48.8 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=43 time=47.9 ms 64 bytes from 8.8.8.8: icmp_req=3 ttl=43 time=48.7 ms 64 bytes from 8.8.8.8: icmp_req=4 ttl=43 time=53.2 ms --- 8.8.8.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 47.975/49.711/53.235/2.063 ms # iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TPLINK" Mode:Managed Frequency:2.427 GHz Access Point: 64:66:xx:xx:xx:22 Bit Rate=108 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=70/70 Signal level=-39 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:3 Missed beacon:0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: f0:7d:68:c1:b4:13 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-67-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:dfbf0000-dfbfffff ip route default via 192.168.0.1 dev eth0 default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 (For the record, I have no idea what the 169.254.0.0 address is doing there.) uname -a 3.2.0-67-generic-pae #101-Ubuntu SMP Tue Jul 15 18:04:54 UTC 2014 i686 i686 i386 GNU/Linux lshw -C network *-network description: Ethernet interface product: NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 01 serial: 00:11:11:59:fc:09 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5751-v3.23a ip=192.168.0.102 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:16 memory:dfcf0000-dfcfffff *-network description: Wireless interface product: AR5418 Wireless Network Adapter [AR5008E 802.11(a)bgn] (PCI-Express) vendor: Qualcomm Atheros physical id: 0 /etc/network/interfaces # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback source /etc/network/interfaces.eth0 source /etc/network/interfaces.wlan0 /etc/network/interfaces.eth0 #Main Interface auto eth0 iface eth0 inet static address 192.168.0.102 netmask 255.255.255.0 gateway 192.168.0.1 /etc/network/interfaces.wlan0 auto wlan0 iface wlan0 inet static address 192.168.0.12 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 netmask 255.255.255.0 wpa-driver wext wpa-ssid TPLINK wpa-ap-scan 1 wpa-proto RSN wpa-pairwise CCMP wpa-group CCMP wpa-key-mgmt WPA-PSK wpa-psk dca1badb5fd4e9axxx4xxdaaxxfa91xx610bxx6a7d57ef67af9809dxx6af42e39 /etc/wpa_supplicant.conf ctrl_interface=/var/run/wpa_supplicant network={ ssid="TPLINK" psk="my password" key_mgmt=WPA-PSK proto=RSN pairwise=CCMP group=CCMP } ifdown eth0 ifdown: interface eth0 not configured ifconfig eth0 Link encap:Ethernet HWaddr 00:11:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:213690 errors:0 dropped:0 overruns:0 frame:0 TX packets:155266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:220057808 (220.0 MB) TX bytes:21137696 (21.1 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196412 errors:0 dropped:0 overruns:0 frame:0 TX packets:196412 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270697 (153.2 MB) TX bytes:153270697 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11335 errors:0 dropped:0 overruns:0 frame:0 TX packets:7287 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2563290 (2.5 MB) TX bytes:855746 (855.7 KB) ifconfig eth0 down ifconfig eth0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:192 (192.0 B) TX bytes:94 (94.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196418 errors:0 dropped:0 overruns:0 frame:0 TX packets:196418 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270871 (153.2 MB) TX bytes:153270871 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11359 errors:0 dropped:0 overruns:0 frame:0 TX packets:7293 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2565482 (2.5 MB) TX bytes:856363 (856.3 KB) ip route default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. --- 8.8.8.8 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3024ms ping -I eth0 -c 3 router PING router (192.168.0.1) from 192.168.0.102 eth0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2015ms ping -I wlan0 -c 3 router PING router (192.168.0.1) from 192.168.0.12 wlan0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2014ms Let me know if you need more info. Thank you in advance.

    Read the article

  • How to switch off wifi on startup or from the console

    - by mit
    I have installed ubuntu 10.04 on a laptop. Wifi is switched on by default on startup. I can disable it rightclicking the network manager icon in the gnome bar. How can I set it to have wifi switched off as default? Alternatively, how can I switch off wifi on the console? I tried already the rfkill command but it does not list any devices and it does not switch off wifi, I tried different parameters. This is a standard install of the Ubuntu 10.04 i386 Desktop Live CD on an IBM T40 Laptop. EDIT A: This is the output of some rfkill commands on my system, and it does not affect the wifi of the laptop: $ rfkill --help Usage: rfkill [options] command Options: --version show version (0.4) Commands: help event list [IDENTIFIER] block IDENTIFIER unblock IDENTIFIER where IDENTIFIER is the index no. of an rfkill switch or one of: <idx> all wifi wlan bluetooth uwb ultrawideband wimax wwan gps fm $ rfkill list $ rfkill list wifi $ rfkill list all $ rfkill list wlan $ sudo rfkill list all $ sudo rfkill block all $ sudo rfkill block wlan $ sudo rfkill block wifi $ EDIT B: Now I found out that sudo ifconfig eth1 down turns it off. And I can turn it on through the gnome network applet again. But the applet does not reflect the change from the commandline, it stills believes wifi is switched on. I have to switch it off and on again on the applet to switch it on again, when I switched it off from the console. Is there a better way? This is what the syslog looks like when I switch wireless off and on again from the network manager: NetworkManager: <info> (eth1): device state change: 3 -> 2 (reason 0) NetworkManager: <info> (eth1): deactivating device (reason: 0). NetworkManager: <info> Policy set '24' (eth0) as default for routing and DNS. NetworkManager: <info> (eth1): taking down device. avahi-daemon[660]: Withdrawing address record for fe80::202:8aff:feba:d798 on eth1. kernel: [ 971.472116] airo(eth1): cmd:3 status:7f03 rsp0:0 rsp1:0 rsp2:0 NetworkManager: <info> (eth1): bringing up device. NetworkManager: <info> (eth1): supplicant interface state: starting -> ready NetworkManager: <info> (eth1): device state change: 2 -> 3 (reason 42) avahi-daemon[660]: Registering new address record for fe80::202:8aff:feba:d798 on eth1.*. kernel: [ 965.512048] eth1: no IPv6 routers present

    Read the article

  • Trying to configure samba share with office server

    - by tomphelps
    Hi, i'm trying to set up fstab to automatically connect to my office shared server. I'm undoubtedly doing something silly here as the username and password and server name work fine in the first code snippet below, just not the second - any help would be appreciated! The following command works as expected... tom@tom-desktop: sudo /usr/bin/smbclient -L Server.local -Uguest Enter guest's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.10] Sharename Type Comment --------- ---- ------- Lacie Disk Disk macosx Server Disk macosx IPC$ IPC IPC Service (Server) ADMIN$ IPC IPC Service (Server) Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.10] Server Comment --------- ------- ACER-9D60040D10 SERVER Server Workgroup Master --------- ------- WORKGROUP ACER-9D60040D10 But when i add the following line to /etc/fstab, i get this error: cifs_mount failed w/return code = -22 //Server.local/Server /media/maguires cifs username=guest,password=password 0 0

    Read the article

  • Best way to handle realtime melee AI in authoritative network environment

    - by PrimeDerektive
    So i've been working on a multiplayer game for a bit; it's a co-op action RPG with real-time combat. If you've seen or played TERA, I'd say it's comparable to that, but not an MMO, heh. I'm currently handling the AI units authoritatively, the server calculates their pathing, movement, and pursue/attack logic, and syncs the movement to the clients 15x per second, and the state changes when they happen. When I emulate 200ms ping, though, the client can perceive being out of range to an AI's attack, but still take the hit, because on the server he hadn't moved that far yet. This also plays hell with my real-time blocking. I don't really want to allow the clients to be allowed to say "that was out of range" or "I blocked that", but I'm not really sure how else to handle it.

    Read the article

  • Best way to cache apt downloads on a LAN?

    - by Ken Simon
    I have multiple Ubuntu machines at home and a pretty slow internet connection, and sometimes multiple machines need to be updated at once (especially during new Ubuntu releases.) Is there a way where only one of my machines needs to download the packages, and the other machines can use the first machine to get the debs? Does it involve setting up my own local mirror? Or a proxy server? Or can it be made simpler?

    Read the article

  • Physics not synchronizing correctly over the network when using Bullet

    - by Lucas
    I'm trying to implement a client/server physics system using Bullet however I'm having problems getting things to sync up. I've implemented a custom motion state which reads and write the transform from my game objects and it works locally but I've tried two different approaches for networked games: Dynamic objects on the client that are also on the server (eg not random debris and other unimportant stuff) are made kinematic. This works correctly but the objects don't move very smoothly Objects are dynamic on both but after each message from the server that the object has moved I set the linear and angular velocity to the values from the server and call btRigidBody::proceedToTransform with the transform on the server. I also call btCollisionObject::activate(true); to force the object to update. My intent with method 2 was to basically do method 1 but hijacking Bullet to do a poor-man's prediction instead of doing my own to smooth out method 1, but this doesn't seem to work (for reasons that are not 100% clear to me even stepping through Bullet) and the objects sometimes end up in different places. Am I heading in the right direction? Bullet seems to have it's own interpolation code built-in. Can that help me make method 1 work better? Or is my method 2 code not working because I am accidentally stomping that?

    Read the article

  • iwlwifi on lenovo z570 disabled by hardware switch

    - by Kevin Gallagher
    It was working fine with windows 7. The hardware switch is not disabled. I've toggled it back and forth dozens of times. The wifi light never turns on and it always lists as hardware disabled. I have the latest updates installed. I've been searching for solutions, but none of them seem to work for me. I've tried removing acer-wmi. I've tried setting 11n_disable=1. I've tried resetting the bios. I've tried using rfkill to unblock (only removes soft block). I've rebooted dozens of times. The wifi light turns off as soon as grub loads. Edit: I have a usb edimax wireless nic. It shows hardware disabled as well (although rfkill lists as unblocked). If I unload iwlwifi the usb nic works fine. uname -a `Linux xxx-Ideapad-Z570 3.2.0-55-generic #85-Ubuntu SMP Wed Oct 2 12:29:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linu`x rfkill list 19: phy18: Wireless LAN Soft blocked: no Hard blocked: yes dmesg [43463.022996] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [43463.023002] Copyright(c) 2003-2011 Intel Corporation [43463.023107] iwlwifi 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [43463.023190] iwlwifi 0000:03:00.0: setting latency timer to 64 [43463.023253] iwlwifi 0000:03:00.0: pci_resource_len = 0x00002000 [43463.023257] iwlwifi 0000:03:00.0: pci_resource_base = ffffc900057c8000 [43463.023261] iwlwifi 0000:03:00.0: HW Revision ID = 0x0 [43463.023797] iwlwifi 0000:03:00.0: irq 43 for MSI/MSI-X [43463.024013] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [43463.024250] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S [43463.045496] iwlwifi 0000:03:00.0: device EEPROM VER=0x15d, CALIB=0x6 [43463.045501] iwlwifi 0000:03:00.0: Device SKU: 0X50 [43463.045504] iwlwifi 0000:03:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [43463.045542] iwlwifi 0000:03:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [43463.045744] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio. [43463.047652] iwlwifi 0000:03:00.0: loaded firmware version 39.31.5.1 build 35138 [43463.047823] Registered led device: phy18-led [43463.047895] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [43463.048037] ieee80211 phy18: Selected rate control algorithm 'iwl-agn-rs' [43463.055533] ADDRCONF(NETDEV_UP): wlan0: link is not ready nm-tool State: connected (global) - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: unavailable Default: no HW Address: 74:E5:0B:4A:9F:C2 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points lshw -C network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:4a:9f:c2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-55-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:43 memory:f1500000-f1501fff lspci 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]

    Read the article

  • Google I/O 2012 - Building Mobile App Engine Backends for Android, iOS and the Web

    Google I/O 2012 - Building Mobile App Engine Backends for Android, iOS and the Web Dan Holevoet, Christina Ilvento Mobile application development is growing at explosive rates and the best of those applications have a backend server. Find out how you can use App Engine's new feature to build powerful APIs to support mobile applications running on Android, iOS, and mobile browsers. For all I/O 2012 sessions, go to developers.google.com From: GoogleDevelopers Views: 1783 43 ratings Time: 48:38 More in Science & Technology

    Read the article

  • How to install hardware drivers for my laptop

    - by John Flisk
    Everytime I change the OS I usually format my laptop. It is an HP tx-2 Touchsmart. It has a touchscreen and additional hardware that isn't working (i.e. volume control buttons and the network discovery) If I was on windows I would just download the hardware drivers from the HP website. How do I go about installing the software for the built-in hardware of my laptop? I am new to the community and I really want to get this computer working like it used to, to get the full Ubuntu experience. Please direct me, thank you.

    Read the article

< Previous Page | 244 245 246 247 248 249 250 251 252 253 254 255  | Next Page >