Search Results

Search found 40420 results on 1617 pages for 'power line networking'.

Page 245/1617 | < Previous Page | 241 242 243 244 245 246 247 248 249 250 251 252  | Next Page >

  • bridge to share WiFi internet connection over eth0

    - by rubo77
    In this script there is implemented that you create a mesh network and connect other machines to your device to serve an internet connection with dhcp: echo "starting bridge to share internet connection over eth0" ifconfig eth0 up promisc brctl addbr br-freifunk brctl addif br-freifunk bat0 brctl addif br-freifunk eth0 echo "internet starting, this may take some minutes due to latency..." echo "(use" echo "tail -f /var/log/syslog" echo "in another window for debugging)" echo echo dhclient br-freifunk echo "The error 'Rather than invoking init scripts through /etc/init.d...' can be ignored:" dhclient br-freifunk # without bridge: dhclient bat0 This works fine with the freifunk-mesh network. But how can I serve internet in a normal case? I would like to connect to any open Wifi I find with my network-manager or wicd (yes, with the graphical GUI) and then start a small script that creates a bridge to my network-out on my laptop I use Ubuntu and my networkcards are eth0 and wlan0

    Read the article

  • Unable to connect to server after a certain amount of time

    - by Troy
    I am a business FIOS subscriber with 5 static IPs. I have the following network setup: Verizon provided ONT Dlink switch Dell server running Ubuntu 12.04 with iptables enabled and a static IP address. The makes/models of hardware are: FIOS ONT Alcatel-Lucent I-211M-H ONT D-Link D-Link Web Smart Switch DES-1228P Server Dell Optiplex 755 (Ubuntu 12.04 Server) I have iptables running on the server with http, https and ssh ports open. I can connect to a website on the server from an external computer, but after a certain amount of time (mins to hours), I can no longer connect. All I have to do to re-enable connectivity is connect to the server via SSH from a computer INSIDE the network. I don't have to actually login, I just have to establish a connection. I can then access the website externally again. I did some googling and it seems some of verizon's equipment had an ARP bug where the ARP entries would expire after a certain time period, but those issues all seem to be from back in 2009 - 2010. I know the switch has an 'auto learning Mac address' feature, but I'm not sure if that could be the problem or not. Does anyone have any ideas or advice on how I can troubleshoot this? Thanks!

    Read the article

  • Access server using IP on another interface

    - by Markos
    I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

    Read the article

  • Funnelling http traffic

    - by spencer p
    I have a situation where a large batch of servers (X), on demand, need to request data from a smaller set of web servers (Y). The worst case scenario is if all servers in X decide to fetch different requests to one server in Y. That would be X amount of connections, which could be a very large burst of traffic. The best case scenario is if 1 server in X hit 1 server in Y in tandem. Life does not work like this. One idea to entertain is placing a proxy, similar to squid between X and Y. All of X servers can connect to this proxy, but would result in a few persistent (http keepalive) connections to Y. If The few were say, 3 or 4, then it would funnel. If we could then rate limit those connections and traffic decides to spike unusually high, we wouldn't hurt anyone but ourselves. Thoughts?

    Read the article

  • Windows 7 PPTP VPN problem

    - by Marco Martins
    Hi, I'm currently using an win 7 as an network server at my home. I've created some shared folders wich can be accessed easily from any pc on my network (win and mac computers) recently I decided to turn on the win 7 pptp to access remotely to my server from anywhere. the problem is with that on, on my router my server ip change, acording to my ipconfig on the cmd my router gets the ip from a "PPP adapter RAS (dial in)". when that happens I cannot access to the shared files over the lan on my mac, but i can connect to the vpn but again can't access to my files. (i've tried connecting to the vpn from another network and it worked, even the file share) anyone can help me? thanks

    Read the article

  • Samsung "Kies via Wifi" doesn't work, stuck on "Loading..."

    - by eyalb99
    When I connect my Galaxy S2 to my laptop using "Kies via Wifi" it doesn't work. On my phone it tells me it is connected, and on the laptop I can see the device "GT-I9100" under connected devices, but I see no files or anything else. When I move the mouse icon over the "GT-I9100", it writes "Loading...". I've waited long enough but nothing happens. When I connect the phone using USB cable, it works perfectly fine.

    Read the article

  • How can I create a VLAN on my extreme switch for a separate subnet/domain?

    - by drpcken
    I'm putting together a small active directory implementation for a buddy of mine. I currently have 2 servers (one is the primary domain controller) and a couple clients. I need to test and run updates on every machine on this domain, but I would have plug them into my current LIVE domain to get it internet access. From what I've read having two separate domains on a single subnet is a bad idea (even though it is temporary) so I don't want to risk messing anything up on my production domain. I'm pretty sure I can create a separate VLAN on my extreme 48 port switch and plug this smaller domain into it on a different subnet, but I don't know the commands. Both subnets would need internet access of course (one of the things I can't wrap my head around is routing internet traffic between subnets (gateway is on production subnet). Switch is a Summit x450e-48p My production domain is on subnet 192.168.200.0. My new domain I want to put online would go into subnet 192.168.10.0. A shove in the right direction would be greatly appreciated. Thank you!

    Read the article

  • How to setup firewall to allow internet connection sharing via Wifi USB stick?

    - by hannanaha
    I have a Windows8 computer linked to the internet via an ethernet cable ("Ethernet" network connection). I have attached to it a DLink Wifi USB stick, and I'm trying to share the main PC's internet connection with my Android phone via a local wifi network. I am using the following batch file to set up this network: netsh wlan set hostednetwork mode=allow ssid=MyWifiName key=password keyUsage=persistent netsh wlan start hostednetwork After I run this script, I can see a new network connection appear in "Control Panel\Network and Internet\Network Connections" named "Local Area Connection *12", and I can see "MyWifiName" on the Android phone. The device name for this connection on the PC is "Microsoft Hosted Network Virtual Adapter". I also set up the "Ethernet" connection to share Internet with "Local Area Connection *12". However, the Android phone usually doesn't manage to obtain an IP from the wireless network, and when it does, there still seems to be no connectivity to the internet. When I turn off the Windows Firewall completely, or even just for "Local Area Connection *12", the Android connection is perfect. My questions are: How should I set up the Windows firewall to allow the phone to connect properly? Is there a specific rule I need to add to the Windows firewall advanced settings? [Note: the above method worked great in Windows 7, without any specific tinkering with the firewall]. Is it safe to turn off the firewall specifically for the "Local Area Connection *12" (the wifi connection) if the main Ethernet connection is still protected by the firewall? Thanks in advance.

    Read the article

  • Asus PCE-N53 11n N600 PCI-E Adapter on 3.x kernel

    - by CITguy
    Problem ASUS PCE-N53 wireless NIC doesn't work for latest versions of the linux kernel. How do I get it working on my system? (Note: I'm posting the answer I've found for others to use.) Installing Driver for Linux 3.x Kernel ASUS provides Linux drivers from their website, but it mentions that the driver supports "Linux Kernel 2.6.x", so it won't work without a some modifications to the driver code. Fortunately, an archlinux forum mentions similar problems and one user was able to create a patch for kernel 3.8.x that seems to work with kernel 3.11.x. Here's how I got it working: Prerequisites Ubuntu: sudo apt-get install build-essential Arch: sudo pacman -S base-devel Steps: 1. Download the driver from the ASUS website The download can be found under "Support Drivers & Tools". 2. Unzip the contents of the downloaded file cd into the new directory 3. Patch The arch forum mentions a 3.8 patch file that needs to be downloaded. Download rt5592sta_fix_64bit_3.8.patch to the current directory. tar -xvf {driver_source.tar.gz} cd into the directory created in previous step patch -p1 < ../rt5592sta_fix_64bit_3.8.patch 4. Compile NOTE: You will need to use sudo for it to compile properly. sudo make sudo make install sudo modprobe rt5592sta 5. Enjoy If all is well, you should now have a working card.

    Read the article

  • Why can't my networks reach each other?

    - by HOLOGRAPHICpizza
    We have two Buffalo WZR-HP-G300NH2 routers, with the default firmware, DD-WRT v24SP2-MULTI (10/31/11) std - build 17798. Each has a separate cable internet connection with a public static IP address. They are both in the 24.123.68.0/24 space. Both of them can contact pretty much the whole internet, and they can both be accessed out on the internet with no problem, but for some reason they can't talk to each other! When I try to ping one from the other I always get "Destination Host Unreachable". There are no strange routing or firewall rules in place. And they are both set to respond to pings, I can ping them from outside. Our main IT guy is going to call our ISP on Monday, but I'm impatient, so does anyone have any ideas?

    Read the article

  • convert home phone wiring to Ethernet

    - by aaa
    can i convert phone wiring in walls to act as only Ethernet network cause the phone wiring is not in use and not connected to the phone company so there is no voltage in the wires i remove the wall plate and i find 6 wires blue,blue/white,green,green/white,orange,orange/white , and i know that Ethernet use 8 here is what i am thinking get Ethernet cable cut it in half and attach wires from wall to the first computer and the same with the other computer so if this is possible do i just attach wires in the same color and ignore brown wire or do i have to rearrange wires , and how much the speed will be thank you in advance

    Read the article

  • How should I troubleshoot a problematic wireless connection on Linux?

    - by Gearoid Murphy
    I recently purchased a netgear 150 usb wireless dongle for use with my 11.10 Xubuntu amd64 system. Using the network-manager interface, I can see local wireless networks and enter the authentication details for my local wireless lan. Unfortunately, the connection does not seem to work, I keep getting notifications that my wireless has disconnected (but none indicating that I've connected). When I examine syslog, it seems to indicate that I've successfully associated with the wireless switch and that dhcp has successfully acquired an ip address but the log shows that the dhcp process keeps sending requests, eventually dropping the connection. 'ifconfig wlan0' never shows the dhcp address logged in syslog. I suspect that the problem lies with the usb dongle, my configuration or the wireless switch but I am not certain how to isolate the problem, can anyone provide some insight on how I should go about homing in on the cause of this problem or verifying the functionality of the individual components, thanks.

    Read the article

  • Second network card configuration not working.

    - by Sebas
    I have 4 servers running Centos 5. All of them have two ethernet network cards. I have configured 192.168.1.x IP addresses on their eth0 card. They are all connected to the same switch using their eth0 card and they are all working. I have configured 10.72.11.x IP addresses on their eth1 card.They are all connected to the same switch - a different one from the switch used with eth0 card - using their eth1 card and they are NOT all working. Their configuration files is like: DEVICE=eth1 BOOTPROTO=static IPADDR=10.72.11.236 BROADCAST=10.72.11.191 NETMASK=255.255.255.192 NETWORK=10.72.11.128 HWADDR=84:2B:2B:55:4B:98 IPV6INIT=yes IPV6_AUTOCONF=yes ONBOOT=yes The interfase is starting and configured as I need. [root@sql1 network-scripts]# ifconfig eth0 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:97 inet addr:192.168.1.105 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::862b:2bff:fe55:4b97/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2981 errors:0 dropped:0 overruns:0 frame:0 TX packets:319 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:386809 (377.7 KiB) TX bytes:66134 (64.5 KiB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:98 inet addr:10.72.11.236 Bcast:10.72.11.191 Mask:255.255.255.192 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:48 Memory:dc000000-dc012800 I also added a route-eth1 file that looks like: 10.0.0.0/8 via 10.72.11.254 Routing looks fine to me: [root@sql1 network-scripts]# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.72.11.192 0.0.0.0 255.255.255.192 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.72.11.254 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 But I cannot ping one server from the other. [root@sql1 network-scripts]# ping 10.72.11.235 PING 10.72.11.235 (10.72.11.235) 56(84) bytes of data. From 10.72.11.236 icmp_seq=1 Destination Host Unreachable From 10.72.11.236 icmp_seq=2 Destination Host Unreachable From 10.72.11.236 icmp_seq=3 Destination Host Unreachable From 10.72.11.236 icmp_seq=4 Destination Host Unreachable From 10.72.11.236 icmp_seq=5 Destination Host Unreachable From 10.72.11.236 icmp_seq=6 Destination Host Unreachable ^C --- 10.72.11.235 ping statistics --- 7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6033ms , pipe 3 What am I doing wrong?

    Read the article

  • ipv6 with KVM on debian

    - by Eliasdx
    I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

    Read the article

  • DNS not responding

    - by Born2win
    I have a Dlink DIR-615 router and I have it around six mounths. My internet connection is VPN (PPTP) based i.e. I have been give a username and password from my isp and my ip address is dynamic. But from few days I am experiencing a serious problem. My router connects normally (i can see yellow light) but my computer is giving "DNS not responding" error. I have tried everything (reset,reboot etc) but no sucess. Any help would be appreciated :)

    Read the article

  • How do I get details about how Network and Sharing Center detected a problem?

    - by Matthew Scouten
    When I open Network and Sharing Center in Windows 7, it puts a red X between the network and the internet, but when I run Troubleshoot Problems it tells me that it does not know what the problem is. Is there any way to tell what test Windows used to place that red X, and how it failed? The system obviously knows something that it is not telling me. Knowing the details would help me solve this problem.

    Read the article

  • ProCurve ACL to prevent a subnet from leaving the switch

    - by kce
    I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (192.0.2.0/24) from ever being able to leave the switch by virtue of being applied to port attached to the upstream connection. The other subnet should be permitted to freely leave the switch. Both subnets are on the same VLAN. Unfortunately SFlow very clearly show broadcast traffic from 192.0.2.0/24 on the upstream connection. ProCurve ACLs are not my strong suit but I feel like I'm missing something very simple here. ip access-list extended "Filter for Camera Network" deny ip 192.0.2.0 0.0.0.255 0.0.0.0 255.255.255.255 log permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 exit interface 24 name "DSL - UPLINK" access-group "Filter for Camera Network" in exit Unless I am mistaken traffic from 192.0.2.0/24 should be dropped as it crosses the uplink port (int 24) whereas all other traffic will be permited by the following default allow rule. What exactly am I missing here? EDIT: Firstly, why do you have two subnets contained in the same VLAN? Because that's how it was configured by a previous administrator and while it makes conceptual sense that a single subnet is "mapped" to a single VLAN there's no technical constraint that I am aware of that makes this have to be the case. Instead of filtering inbound traffic on your uplink, you should be filtering outbound traffic. The HP2600 series can only filter inbound traffic on interfaces. Should I change my filter to deny any to 192.0.2.0/24?

    Read the article

  • Why would my mouse pointer be jerky when it can't get a signal from my router?

    - by izb
    I've got a fairly new PC but when moving the mouse across the screen, the pointer jerks as if the PC is freezing momentarily every second or so. Strangely, this only seems to happen if the signal from the wifi router is bad. If I move the PC closer to the router to get a full signal, it's fine. It also seems to affect the keyboard; Opening notepad and holding down a key shows the same momentary freezes. -- Update: It's a logitech wireless mouse, and a wired USB logitech keyboard.

    Read the article

  • netkit: why cant my router 4 pc4 ping my router 1 pc1 - how can I solve this please?

    - by donok
    Below I have four routers connected but my pc1 on r1 cannot ping my pc4 on r4 and also my pc2 on r2 cant ping my pc4 on r4 and vice versa. Below is a network diagram: and the configurations are below that, could anyone help me please on making them accessible? ![connecting 4 routers][1] I cant post my diagram on serverfault(less than 10 rep) so I did on stackoverflow and asked the same question. pc1: ifconfig eth0 195.11.14.5 netmask 255.255.255.0 broadcast 195.11.14.255 up route add default gw 195.11.14.1 dev eth0 pc2.start: ifconfig eth0 200.1.1.7 netmask 255.255.255.0 broadcast 200.1.1.255 up route add default gw 200.1.1.1 dev eth0 pc3: ifconfig eth0 195.20.14.9 netmask 255.255.255.0 broadcast 195.20.1.255 up route add default gw 195.20.14.1 dev eth0 pc4: ifconfig eth0 200.2.1.11 netmask 255.255.255.0 broadcast 200.2.1.255 up route add default gw 200.2.1.1 dev eth0 r1: ifconfig eth0 195.11.14.1 netmask 255.255.255.0 broadcast 195.11.14.255 up ifconfig eth1 100.0.0.9 netmask 255.255.255.252 broadcast 100.0.0.11 up route add -net 200.1.1.0 netmask 255.255.255.0 gw 100.0.0.10 dev eth1 route add default gw 100.0.0.10 lab.conf: if you need more on that Ill post it up but I think most of the info is there. Any help would be greatly appreciated especially trying to make a connection between pc4 and pc1, even if you think it does not make sense please explain why. Thank you.

    Read the article

  • How do I map a network drive in Ubuntu? I want to save my Firefox downloads directly in the mapped n

    - by NJTechie
    I work in an environment wherein files are exchanged over email which are then processed into databases. In Windows, mapping a network drive and storing files directly to a folder in the network drive from Firefox/Chrome downloads is a breeze. How to achieve the same in Ubuntu? I don't see the SFTP'ed drive/directory as options in Firefox- Downloads setup. Thanks in advance!

    Read the article

  • How do I map a network drive in Ubuntu? I want to save my Firefox downloads directly in the mapped n

    - by NJTechie
    I work in an environment wherein files are exchanged over email which are then processed into databases. In Windows, mapping a network drive and storing files directly to a folder in the network drive from Firefox/Chrome downloads is a breeze. How to achieve the same in Ubuntu? I don't see the SFTP'ed drive/directory as options in Firefox- Downloads setup. Thanks in advance!

    Read the article

  • Setup windows 2012 AD in Hyper-V for a Test environment

    - by hub
    Im trying to setup a Windos 2012 R2 test environment on my work computer (a laptop). I have a AD, DHCP and DNS server on server A, and a client connecting to the doman and that works. The client can ping the AD server and gets a valid IP adress. If I ping google.com from the client I get the IP adress but I dont get any responses (request time out). If i ping google.com from server A it works as it should. Server A have a connection to the Internet through a "external network switch" in hyper-v, which gets its internet from a router and the client is connected to a "internal network switch". May the poblem be that server A is behind a router? Can I make this solution to work regadless the network my laptop is connected to? At home i have one IP adress, at work its a totally different range. What I would like is to use my laptops internet connection, regardless wifi or wired, to act as incomming internet, is this possible?

    Read the article

  • Routing Traffic on Ubuntu to give Raspberry PI Internet Access

    - by Scruffers
    I'm hoping someone can point me in the right direction for setting up my Linux (Ubuntu 12.04) box to route traffic from eth0 to wlan0. I'll try and explain the problem I am trying to solve: I currently have two separate networks: [RaspberryPi/eth0] 192.168.2.2 / 255.255.255.0 ^ | v [Ubuntu/eth0] 192.168.2.1 / 255.255.255.0 And: [Ubuntu/wlan0] 192.168.1.100 / 255.255.255.0 ^ | v [ADSL router] 192.168.1.1 / 255.255.255.0 So currently if I want to access the RaspberryPI I can SSH from the Ubuntu box to the PI. And if I want to use the Internet, I have full access from the Ubuntu box, but nothing from the RaspberryPI - the two networks are partitioned. What I would like to do is configure things so that the RaspberryPI has Internet access via the Ubuntu box and out to the Internet. I tried to create a bridge, but got the message "wlan0: operation not supported" (wireless chipset is Ralink RT3062). I'm sure giving the Raspberry PI Internet access should be easy to do in this configuration, but I am a bit lost - can someone point me in the right direction please?

    Read the article

< Previous Page | 241 242 243 244 245 246 247 248 249 250 251 252  | Next Page >