Search Results

Search found 926 results on 38 pages for 'ignoring'.

Page 26/38 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

• Is basing storage requirements based on IOPS sufficient?

  - by Boden

  The current system in question is running SBS 2003, and is going to be migrated on new hardware to SBS 2008. Currently I'm seeing on average 200-300 disk transfers per second total across all the arrays in the system. The array seeing the bulk of activity is a 6 disk 7200RPM RAID 6 and it struggles to keep up during high traffic times (idle time often only 10-20%; response times peaking 20-50+ ms). Based on some rough calculations this makes sense (avg ~245 IOPS on this array at 70/30 read to write ratio). I'm considering using a much simpler disk configuration using a single RAID 10 array of 10K disks. Using the same parameters for my calculations above, I'm getting 583 average random IOPS / sec. Granted SBS 2008 is not the same beast as 2003, but I'd like to make the assumption that it'll be similar in terms of disk performance, if not better (Exchange 2007 is easier on the disk and there's no ISA server). Am I correct in believing that the proposed system will be sufficient in terms of performance, or am I missing something? I've read so much about recommended disk configurations for various products like Exchange, and they often mention things like dedicating spindles to logs, etc. I understand the reasoning behind this, but if I've got more than enough random I/O overhead, does it really matter? I've always at the very least had separate spindles for the OS, but I could really reduce cost and complexity if I just had a single, good performing array. So as not to make you guys do my job for me, the generic version of this question is: if I have a projected IOPS figure for a new system, is it sufficient to use this value alone to spec the storage, ignoring "best practice" configurations? (given similar technology, not going from DAS to SAN or anything)

  Read the article

• IIS 7.0 404 Custom Error Page and web.config

  - by Colin

  I am having trouble with a custom 404 error page. I have a domain running a .NET proj with it's own error handling. I have a web.config running for the domain which contains: <customErrors mode="RemoteOnly"> <error statusCode="500" redirect="/Error"/> <error statusCode="404" redirect="/404"/> </customErrors> On a sub dir of that domain I am ignoring all routes there by doing routes.IgnoreRoute("Assets/{*pathInfo}"); in the .NET proj and I want to put a custom 404 error page on that and any sub dir's of Assets. The sub dir contains static content like images, css, js etc etc. So in the Error Pages section of IIS I put a redirect to an absolute URL. The web.config for that dir looks like the following: <system.webServer> <httpErrors> <remove statusCode="404" subStatusCode="-1" /> <error statusCode="404" prefixLanguageFilePath="" path="http://mydomain.com/404" responseMode="Redirect" /> </httpErrors> </system.webServer> But I navigate to an unknown URL under that dir and yet I still see the default IIS 404 page. I am also seeing an alert in IIS that reads: You have configured detailed error messages to be returned for both local and remote requests. When this option is selected, custom error configuration is not used. Does this have anything to do with the customErrors mode="RemoteOnly" in the site web.config? I have tried to overwrite the customErrors in the sub dir web.config but nothing changes. Any help would be appreciated. Thanks.

  Read the article

• How to install port versions of perl modules for perl5.14 in freebsd 9.0

  - by jm666

  Trying to use perl5.14 on Freebsd with port based p5-modules. uname -impr 9.0-RELEASE amd64 amd64 ALTQ delete all installed ports, start with a clean system # pkg_delete -a # rm -rf /var/db/pkg /var/db/ports /usr/local installing portmaster, checking /etc/make.conf (here is only WITHOUT_X11=YES). Now installing perl. # portmaster -g --force-config lang/perl5.14 # perl -v This is perl 5, version 14, subversion 2 (v5.14.2) built for amd64-freebsd-multi Now perl modules from the ports, # portmaster -g devel/p5-Moose #install Moose and its deps check with pkg_info and got zilion errors like: # pkg_info pkg_info: corrupted record (pkgdep line without argument), ignoring dpendecy check with portmaster - showing dependecies on perl5.12 #portmaster --check-depends Checking p5-Class-C3-0.24 ===>>> lang/perl5.12 is listed as a dependency ===>>> but there is no installed version ===>>> Delete this dependency data? y/n [n] when tried # perl-after-upgrade -f got: Fixed 0 packages (0 files moved, 0 files modified) In short: i got installed Moose into /usr/local/lib/perl5/site_perl/5.14.2/ but all its dependencies into /usr/local/lib/perl5/site_perl/5.12.4/ Yes, it is possible fix this with: # portmaster p5- what reinstall all installed p5-packages once again, now correctly for the 5.14 but it is terrible installing them twice... Questions: What is the correct way install p5-MODULES from ports with installed perl5.14 in an clean system? How to fix wrong dependency data on perl5.12 without the need install and reinstall them again What i'm doing wrong? Ps: know perlbrew and/or Local::lib - but for this case - want port versions.

  Read the article

• Formula to calculate probability of unrecoverable read error during RAID rebuild

  - by OlafM

  I need to compare the reliability of different RAID systems with either consumer or enterprise drives. The formula to have the probability of success of a rebuild, ignoring mechanical problems, is simple: error_probability = 1 - (1-per_bit_error_rate)^bit_read and with 3 TB drives I get 38% probability to experience an URE (unrecoverable read error) for a 2+1 disks RAID5 (4.7% for enterprise drives) 21% for a RAID1 (2.4% for enterprise drives) 51% probability of error during recovery for the 3+1 RAID5 often used by users of SOHO products like Synologys. Most people don't know about this. Calculating the error for single disk tolerance is easy, my question concerns systems tolerant to multiple disks failures (RAID6/Z2, RAIDZ3 and RAID1 with multiple disks). If only the first disk is used for rebuild and the second one is read again from the beginning in case or an URE, then the error probability is the one calculated above squared (14.5% for consumer RAID5 2+1, 4.5% for consumer RAID1 1+2). However, I suppose (at least in ZFS that has full checksums!) that the second parity/available disk is read only where needed, meaning that only few sectors are needed: how many UREs can possibly happen in the first disk? not many, otherwise the error probability for single-disk tolerance systems would skyrocket even more than I calculated. If I'm correct, a second parity disk would practically lower the risk to extremely low values. Am I correct?

  Read the article

• Surprising corruption and never-ending fsck after resizing a filesystem.

  - by Steve Kemp

  System in question has Debian Lenny installed, running a 2.65.27.38 kernel. System has 16Gb memory, and 8x1Tb drives running behind a 3Ware RAID card. The storage is managed via LVM. Short version: Running a KVM guest which had 1.7Tb storage allocated to it. The guest was reaching a full-disk. So we decided to resize the disk that it was running upon We're pretty familiar with LVM, and KVM, so we figured this would be a painless operation: Stop the KVM guest. Extend the size of the LVM partition: "lvextend -L+500Gb ..." Check the filesystem : "e2fsck -f /dev/mapper/..." Resize the filesystem: "resize2fs /dev/mapper/" Start the guest. The guest booted successfully, and running "df" showed the extra space, however a short time later the system decided to remount the filesystem read-only, without any explicit indication of error. Being paranoid we shut the guest down and ran the filesystem check again, given the new size of the filesystem we expected this to take a while, however it has now been running for 24 hours and there is no indication of how long it will take. Using strace I can see the fsck is "doing stuff", similarly running "vmstat 1" I can see that there are a lot of block input/output operations occurring. So now my question is threefold: Has anybody come across a similar situation? Generally we've done this kind of resize in the past with zero issues. What is the most likely cause? (3Ware card shows the RAID arrays of the backing stores as being A-OK, the host system hasn't rebooted and nothing in dmesg looks important/unusual) Ignoring brtfs + ext3 (not mature enough to trust) should we make our larger partitions in a different filesystem in the future to avoid either this corruption (whatever the cause) or reduce the fsck time? xfs seems like the obvious candidate?

  Read the article

• Why do clients on Branch Sites insist on accessing SYSVOL on the HQ DC instead of the branches' RODC?

  - by pepoluan

  I'm still scratching my head over this situation... You see, we have 3 RW DCs in the HQ, and 1 RODC on every branch sites (50+ locations). During startup, a script will pull in some files from \\example.com\SYSVOL\example.com\Common\Data But we have been experiencing bandwidth overload. A traffic analysis indicated that lots of clients in the Branch Sites were trying to access the SYSVOL located in the RW DCs. E.g.: If the RW DCs are 10.1.0.15, 10.2.0.15, and 10.3.0.15, and site 'X' has a subnet of 10.27.0.0/16 (with its RODC at 10.27.0.15), clients at site 'X' seem to insist on accessing \\10.1.0.15\SYSVOL or \\10.2.0.15\SYSVOL or \\10.3.0.15\SYSVOL; they seem to be ignoring the RODC completely. What is going on here? Where should I start investigating what went wrong? BTW, I'm already using DFS-R, and replication have been going on successfully; I can put a small 'canary' file on one of the RW DCs, and within minutes all the RODCs will have successfully replicated the 'canary' file.

  Read the article

• PHP Output buffer flush issue on Apache/Linux

  - by Iiro Vaahtojärvi

  Hi, I'm running into issues with the PHP output buffer flushing on my Linux web server. The output buffer is maintained correctly and all the right data is pushed to it in my code, but the usual flushing mechanisms won't flush it to the browser. I have tried everything posted here: http://php.net/manual/en/function.flush.php but no success so far. I got a small script from php.net to test it: <?php ob_start(); for($i=0;$i<70;$i++) { echo 'printing...<br />'; ob_get_flush(); flush(); usleep(300000); } ?> This should print "printing..." to the browser 70 times, one line every three seconds. This works fine on my other testing environment which is based on Windows (still using apache, XAMPP package), but on my Linux server it doesn't. It waits for the script to finish before giving anything to the browser, basically ignoring the whole flush command. If anyone has experienced this before or knows of anything that could help (be it server configuration or adjustment to code) it would be greatly appreciated!

  Read the article

• WEIRD netstat behavior on Windows XP re: www.partypoker.com

  - by tbone

  I really don't know if this is the right place to ask this, but I would really appreciate if someone that is more savvy on Windows XP (Professional) could help me out. For background, I am a 10+ years programmer, so I'm not a total idiot, but I am far from an expert on TCP/IP, etc, and this has me totally confused. When I do a netstat (on Windows XP) I seem to always get a huge amount of www.partypoker.com connections and I can't figure out where they are coming from. A netstat -o shows me that some are coming from PID xxx, which is firefox, but if I kill it, the connections still remain. Some are coming from PID 0, which makes no sense to me. SECOND PROBLEM: One would think you could edit the C:\WINDOWS\system32\drivers\etc\hosts file to block this, but it seems like my machine is ignoring the hosts file! (I have tried with the DNS client service both enabled and disabled, same result). So I just rebooted, killed all my normal programs, and I can't seem to reproduce the problem. If I was a paranoid person, I would think there was some sort of an intelligent trojan running. I am running Windows XP Pro, Kaspersky Antivirus, ccCleaner, and am fully up to date on Windows Update. What gives???? So, I guess my questions are: 1. Is anyone else seeing these wird connections to partypoker.com? 2. Why isn't my hosts filter working? 3. Is there some utility I can run to find out whats happening? I've tried autoruns.exe from sysinternals but don't see anything interesting. Am I the only one with this problem? If there are any additional things you need me to run, let me know.

  Read the article

• Postfix: How do I Make Email Aliases Work?

  - by Nick

  The documentation claims that I can add aliases in a file (like /etc/postfix/virtusertable) and then use the "virtual_maps" directive to point to it. This does not appear to be working, however. My mail is bouncing with: Recipient address rejected: User unknown in local recipient table; If I mail the user from the server using the mail command, it works. mail myuser The message goes through postfix and inserts itself in the Cyrus inbox correctly. When I use fetchmail to get the user's messages off a pop3 server, postfix fails. The user's email is "[email protected]", but it doesn't seem to be mapping correctly to "myuser", the cyrus mailbox name. /etc/postfix/main.cf myhostname = localhost alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all mailbox_transport = lmtp:unix:/var/run/cyrus/socket/lmtp #lmtp:unix:/var/run/lmtp virtual_alias_domains = mydomain.com virtual_maps = hash:/etc/postfix/virtusertable /etc/fetchmailrc et syslog; set daemon 20; poll "mail.pop3server.com" with protocol pop3 user "[email protected]" password "12345" is "myuser" fetchall keep /etc/postfix/virtusertable [email protected] myuser postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_size_limit = 0 mailbox_transport = lmtp:unix:/var/run/cyrus/socket/lmtp mydestination = localhost myhostname = localhost mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes virtual_alias_domains = mydomain.com Why is it ignoring my alias?

  Read the article

• Disable "Do you want to change the color scheme to improve performance?" warning

  - by William Lawn Stewart

  Sometimes this dialog box will pop up (see screenshot below). Every time it appears I select "Keep the current color scheme, and don't show this message again". Windows then reminds me again -- either the next day or after reboot, or sometimes another 5 minutes later. Do you want to change the color scheme to improve performance? Windows has detected your computer's performance is slow. This could be because there are not enough resources to run the Windows Aero color scheme. To improve performance, try changing the color scheme to Windows 7 Basic. Any change you make will be in effect until the next time you log on to Windows Change the color scheme to Windows 7 Basic Keep the current color scheme, but ask me again if my computer continues to perform slowly Keep the current color scheme, and don't show this message again Is there some reason why Windows is ignoring/forgetting my attempts to suppress the dialog? I'd love to never ever see it again, it's annoying, and it alt-tabs me out of fullscreen applications. If it matters, I'm running Windows 7 x64 Professional. I believe the dialog appears because I'm forcing Vsync and Triple Buffering for DirectX applications.

  Read the article

• Asus K55VM usb 3.0 issue

  - by user2141481

  Good day superusers! I own the above laptop and I found out that there are some unknown and unusual issues with usb 3.0 ports. I haven't noticed anything strange until now. I got a new toshiba usb 3.0 external hdd and when I try to copy larger amount of data from my disk to the external hdd, the OS(windows 7) randomly starts ignoring the external hdd. It doesn't shut it down, it kinda just stops responding but the light on the hdd is still lit. I get an error that the files cannot be copied. I have reinstalled windows 7, installed all drivers(including intel chipset drivers of course) and the issue is still present. It acts normal when copying small amount of data. Also, I heard that some intel chipsets have an issue with usb, something about the connectors not transferring power when the usb device enters some kind of "low power mode" causing the device to stop responding and you need to plug it out and in again. But the thing is, my Intel® Chief River Chipset HM76 is not on the list of affected hardware(not ENTIRELY sure though). If anyone has any idea of what the problem to this might be, I'd be greatful. Edit: The hdd works perfectly fine even for large amounts of data if plugged in the usb 2.0 port!

  Read the article

• IIS SMTP server (Installed on local server) in parallel to Google Apps

  - by shaharru

  I am currently using free version of Google Apps for hosting my email.It works great for my official mails my email on Google is [email protected]. In addition I'm sending out high volume mails (registrations, forgotten passwords, newsletters etc) from the website (www.mydomain.com) using IIS SMTP installed on my windows machine. These emails are sent from [email protected] My problem is that when I send email from the website using IIS SMTP to a mail address [email protected] I don’t receive the email to Google apps. (I only receive these emails if I install a pop service on the server with the [email protected] email box). It seems that the IIS SMTP is ignoring the domain MX records and just delivers these emails to my local server. Here are my DNS records for domain.com: mydomain.com A 82.80.200.20 3600s mydomain.com TXT v=spf1 ip4: 82.80.200.20 a mx ptr include:aspmx.googlemail.com ~all mydomain.com MX preference: 10 exchange: aspmx2.googlemail.com 3600s mydomain.com MX preference: 10 exchange: aspmx3.googlemail.com 3600s mydomain.com MX preference: 10 exchange: aspmx4.googlemail.com 3600s mydomain.com MX preference: 10 exchange: aspmx5.googlemail.com 3600s mydomain.com MX preference: 1 exchange: aspmx.l.google.com 3600s mydomain.com MX preference: 5 exchange: alt1.aspmx.l.google.com 3600s mydomain.com MX preference: 5 exchange: alt2.aspmx.l.google.com 3600s Please help! Thanks.

  Read the article

• Unable to run cvlc in a script

  - by VxJasonxV

  I'm creating a script that issues a few curl commands in order to access a time-protected mms stream link, then set up a relay using cvlc (vlc's command line interface) for my own use on an unencumbered player. The curl aspect of this is working, as I can run as a browser and curl side by side and get the same access url. (It's time locked meaning the stream will work forever, but you have to connect quickly or the URL will time out.) The very end of the script prints the command I will run, which is then followed up by "exec $CMD". When I echo $CMD I get: cvlc --sout '#standard{access=http,mux=asf,dst=0.0.0.0:58194}' mms://[...] But the cvlc execution output says: [0x9743d0] main interface error: no suitable interface module [0x962120] main libvlc error: interface "globalhotkeys,none" initialization failed [0x9743d0] dummy interface: using the dummy interface module... [0xb16e30] stream_out_standard stream out error: no mux specified or found by extension [0xb16ad0] main stream output error: stream chain failed for `standard{mux="",access="",dst="'#standard{access=http,mux=asf,dst=0.0.0.0:58194}'"}' [0xb11cd0] main input error: cannot start stream output instance, aborting [0xb11f70] signals interface error: Caught Interrupt signal, exiting... Why is it ignoring my --sout input?

  Read the article

• WOL doesn't work if set to anything other than `a` but this setting makes it boot all the time

  - by Elton Carvalho

  I manage a small "cluster" of 4 Xeon machines with Intel boards in my lab. They are all plugged to a 5-port 3-Com switch with static IP addresses like 10.0.0.x. They are all running OpenSuse 11.4 and their /home/ is served by one of the machines (node00) via NFS. They are plugged to an UPS that can keep them on for ca. 15 minutes, but there are lots of electric shortages due to "unscheduled maintenace" that are longer than this. So they end up being powered down without notice. If I set the BIOS to turn them on after power shortages, the issue is that they all boot at the same time and, if node00 decides to run fsck in the /home/ partition, it does not finish booting before the others try to NFS mount their /home/. I am trying to make wake on lan work, so I can choose to boot the NFS clients only after the server has successfully booted. The problem is that when I run ethtool I get an output like this: Supports Wake-on: pumbag Wake-on: g Theoretically, it is set to wake on MagicPacket(tm), according to the manual. But sending the WOL packet using wol -i 10.0.0.255 $MACADDR does not wake up the box after I shut it down with halt. The ethernet link led blinks after I send the packet, so it appears to be getting to the machine. However, if I set it up with ethtool -s eth1 wol bag, the machine always wakes up right after halting, even if I don't send the Magic packet. This means that the device can wake up with LAN activity, but seems to be ignoring the magic packet. Setting wol ag does not wake the box with the MagicPacket. Does setting wol a mean that it should boot with any broadcast message? How can I diagnose the issue of the machine not waking up with the MagicPacket even though I am sending it and it's set up to wake up with it? Thanks in advance!

  Read the article

• Move a screen session back to its original PID

  - by cron410

  Installed McMyAdmin (minecraft manager) on Ubuntu 12.04 32 bit. Wrote my own service to start McMyAdmin (.net app running in Mono) in its own screen session, and be able to inject proper McMyAdmin commands into that session with the init.d script. Its been running great! Today, I decided to start installing a Source dedicated server (counterstrike pro mod) I determine its going to be a long download process so I quit the process and fire up a fresh screen session called "source". I paste the command in, but it has a space at the begining and bash complains of ignoring semaphores or some such. I detach and reattach the session. Its sliding like butter. I ctrl+a-d out of the session and start exploring the new folder structure and figure out where I need to place a symbolic link. I go to resume that screen and this is what I see: $screen -r source There are several suitable screens on 20091.source (12/02/12 22:59:53) (Detached) 19972.source (12/02/12 22:57:31) (Detached) 917.minecraft (11/30/12 15:30:37) (Attached) It appears I am connected to the minecraft screen?!?!?! So I attach to the other screens one at a time. minecraft is running in 19972.source and sourceds is running in 20091.source So how the hell did I move the minecraft process to another session called source and my main terminal is now "attached" to the minecraft screen? more: I just used exit to quit the putty session, then logged back in, its still the same. did that 3 more times and now the minecraft screen is gone and everything is acting as it should except, of course, for the session name and start time of the "new" minecraft screen. Should I just submit this as a bug for GNU screen?

  Read the article

• Messed up partitions... system will not boot!

  - by someguy

  I did a really dumb thing. cfdisk threw an error at me saying "FATAL ERROR: Bad primary partition 3: Partition ends in the final partial cylinder", so I installed Partition Table Doctor to see if I could fix the problem. When the program started up, it told me there were problems with my partitions, and asked if I wanted them fixed (cannot remember real message, but I believe it had something to do with the cylinder boundaries), so, blindly, without thinking of the consequences, I did. Now, my system will not boot. I tried booting from the Windows 7 installation CD. I went to install a fresh copy, but it said that "No drives were found". I then opened up diskpart. According to diskpart, there is only one partition, containing one volume, assigned the letter "C". Before, I had four partitions! It is also saying that the file system is RAW. Is there any way I can fix this? I have important data that I do not want to lose. Later on... I tried fdisk with the option -l, which lists the partition table(s), and this is what I got: Ignoring extra extended partition 4 Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 64 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x163df116 Device Boot Start End Blocks Id System /dev/sda1 6 18 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 18 7851 62918572+ 7 HPFS/NTFS /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30403 139203193 7 HPFS/NTFS I don't know if this will help, but it's extra information, at least. Also, this is how I had my partitions: 40MB (Unallocated) 100MB (System Reserved) 60GB (Windows, C:) 40GB (Was reserved for secondary OS) ~132GB (Home, E:)

  Read the article

• Ignore non-unicode programs language when installing software

  - by mitya

  This is something that is driving me nuts for a while and I haven't been able to find a solution for this problem anywhere. I am running Windows 7 and my "Language for non-Unicode programs" setting is set to Russian. I need for some non-unicode software that has a Russian UI. However, for most of my software I prefer to use the English UI. A lot of software out there is multilingual and is too smart for my liking. When installing, it switches the UI to Russian and the software UI stays in Russian after the installation without an option to change that, besides setting the "non-unicode language" to English. It switches back to Russian once I revert the setting and reboot. Most of the time it is driver software, i.e: Intel, HP, etc. How can force the installation to run English and stay that way after install, ignoring the "Language for non-Unicode programs" setting? Now, I understand this might be specific to the installer: MSI, Install Shield, etc. But any solution will be good, even if I have to apply it for every software installation. Thanks in advance for any helpful information!

  Read the article

• Google Drive terminates without error on startup

  - by Iszi

  I've used Google Drive for awhile now, but it won't start up after installing on my latest system re-build. I'm still using the same OS, hardware, and basic software load (antivirus, firewall, etc.) that I have for years during which I had not previously had problems with Drive. OS: Windows 7 Ultimate x64 Google Drive Version: 1.12.5329.1887 Now, whenever I try to run Google Drive, it just spawns two instances of the executable which die shortly after. No error messages are posted to the desktop, and nothing indicating any problem is written to the Event Log. After some research, I've yet to find anyone having the same problem who's found an answer. I did find out how to run Google Drive in diagnostic mode, using the --vv parameter at the command line. After that, I opened up the sync log and got this: 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 OS: Windows/6.1.7601-SP1 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 Google Drive (build 1.12.5329.1887) 2013-10-31 17:11:24,039 DEBUG pid=3664 1892:MainThread logging:1608 DEBUGGING DUMP is ON. 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 ERROR, UNEXPECTED EXCEPTION 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 [Error 5] Access is denied Traceback (most recent call last): File "<string>", line 232, in Main File "<string>", line 118, in RegisterCustomFileTypes File "P:\p\agents\hpal4.eem\recipes\353983091\base\b\drb\googleclient\apps\webdrive_sync\windows\build\pyi.win32\main\outPYZ1.pyz/windows.registry", line 62, in GetValue WindowsError: [Error 5] Access is denied 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Crash reporting disabled. Ignoring report. 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Exiting with error code: 0 I'm running on an account with Administrator-level permissions, and have even tried using "Run As Administrator" on the EXE. I'm not sure why it's looking for a P:\ drive, as no such volume has ever been mounted on this system. What should I do to try to further troubleshoot, and resolve, this issue?

  Read the article

• proxy pass domain FROM default apache port 80 TO nginx on another port

  - by user10580

  Im still learning server things so hope the title is descriptive enough. Basically i have sub.domain.com that i want to run on nginx at port 8090. I want to leave apache alone and have it catch all default traffic at port 80. so i am trying something with a virtual name host to proxy pass to sub.domain.com:8090, nothing working yet and go no idea what the right syntax could be. any ideas? most of what i found was to pass TO apache FROM nginx, but i want to the do the opposite. LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_http_module modules/mod_proxy_http.so <VirtualHost sub.domain.com:80> ProxyPreserveHost On ProxyRequests Off ServerName sub.domain.com DocumentRoot /home/app/public ServerAlias sub.domain.com proxyPass / http://appname:8090/ (also tried localhost and sub.domain.com) ProxyPassReverse / http://appname:8090/ </VirtualHost> when i do this i get [warn] module proxy_module is already loaded, skippin [warn] module proxy_http_module is already loaded, skipping [error] (EAI 2)Name or service not known: Could not resolve host name sub.domain.com -- ignoring! and yes, the app is working (i have it running on port 80 with another subdomain) and it works at sub.domain.com:8090

  Read the article

• named responding recursive on norecurse queries

  - by Keks

  I have a server on which named is running. It is intercepted with another named server which it is not aware of. Querying the first named server results in timeouts. The server tries to resolve the query recursively. During that the firewall redirects the DNS Request from the first named server to the second one (the query from the first one is addressed to a e.g. a root server and has its "Recursion desired" bit set to 0). Despite that the second named responds to this request with a entirely or at least 1 level more resolved response than the first named server expects. So it ends up with a timeout even though it got a correct name server or even the full IP for the queried domain. In the first case the first name server tries to follow the authority domain ignoring the coresponding glue record and ends up in a loop it aborts: queried: google.com -> got from named#2: ns1.google.com -> ignore glue record and query: ns1.google.com -> got authority from named#2: google.com In the second case it ignores the answer section with the correct IP and instead tries to follow the name servers from the authority section, which ends up in the same dead end as case 1. So how can it be that the second named responds with recursive results even though the bit was explicitly set to 0 in the request from the first named?

  Read the article

• Calculating memory footprints using /proc/sysvipc/shm

  - by MarkTeehan

  This is for a SLES 10 database server. One of my servers runs three databases and three app servers; I am analyzing how their shared memory segments grow and shrink to avoid intermittent out-of-memory scenarios. "Top" is hot helpful for this since its calculations for RES and VIRT are inconsistent. I am doing this by matching up the contents of /proc/sysvipc/shm with memory usage reported by the database admin console. I do this by totaling up saving the contents of /proc/sysvipc/shm and then total up "bytes" for all of the segments for the offending userid. This is a large server with hundreds of segments and tens (or hundreds) of GB of allocated memory per userid. However it doesn't match up - the database management software claims to be using around 25% more memory than the total I calculate. Negligible swap space is in use, so I am ignoring that. I am running it as root so I am sure I see all shared memory segments. My question is : is all (significant) allocated memory recorded in /proc/sysvipc/shm, or is this only shared memory (*and not "un-shared" memory?). If this is incorrect, what is the correct way to calculate out the total allocated memory for each userid? Also: I believe doing a 'cat' on this file locks server IPC. I check it every 5 seconds - is it likely that this frequency could be problematic? Thanks! Mark Teehan Singapore

  Read the article

• How can I ensure that my static ip address is read from /etc/network/interfaces rather than dhcp?

  - by jonderry

  This is a follow up to the following question. I'm trying to set a static IP by changing /etc/network/interfaces to the following: # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.2.133 netmask 255.255.255.0 gateway 192.168.2.1 dns-nameservers 8.8.8.8 and then running /sbin/ifdown eth0; /sbin/ifup eth0. However, the change in IP address doesn't appear to take effect without editing /etc/dhcp/dhclient.conf and commenting out the following before running ifdown; ifup: request subnet-mask, broadcast-address, time-offset, routers, domain-name, domain-name-servers, domain-search, host-name, dhcp6.name-servers, dhcp6.domain-search, netbios-name-servers, netbios-scope, interface-mtu, rfc3442-classless-static-routes, ntp-servers, dhcp6.fqdn, dhcp6.sntp-servers; Strangely, after commenting out this line, running ifdown; ifup works, but when I uncomment it, the behavior does not revert to the previous behavior of ignoring changes to my settings in /etc/network/interfaces (this doesn't seem like a problem, but I really need to be able to repeat this problem so that I can be confident that my solution is robust) Also, I'd rather not have to edit /etc/dhcp/dhclient.conf to change my static IP since it seems I should be able to do this by only editing interfaces. Can anyone explain the issues I'm seeing above and suggest the best way of making changes to static IP addresses take effect that admits reproducibility so that I can be sure that my approach works?

  Read the article

• Cannot Install Windows 7 SP1 (64-bit)

  - by Clever Human

  I have tried every way I know how to get Windows 7 SP1 to install. It fails every time. Below is what looks like the relevant contents of the CBS.Log file. If there are further details that would help or more information I can gather, I will get it. 2011-08-15 10:32:52, Info CBS Startup: Package: Package_for_KB976902~31bf3856ad364e35~amd64~~6.1.1.17514 completed startup processing, new state: Installed, original: Installed, targeted: Installed. hr = 0x80070490 2011-08-15 10:32:52, Info CBS WER: Generating failure report for package: Package_for_KB976932~31bf3856ad364e35~amd64~~6.1.1.17514, status: 0x80070490, failure source: CBS Other, start state: Partially Installed, target state: Installed, client id: SP Coordinater Engine 2011-08-15 10:32:52, Info CBS Failed to query DisableWerReporting flag. Assuming not set... [HRESULT = 0x80070002 - ERROR_FILE_NOT_FOUND] 2011-08-15 10:32:52, Info CBS Failed to add %windir%\winsxs\pending.xml to WER report because it is missing. Continuing without it... 2011-08-15 10:32:52, Info CBS Failed to add %windir%\winsxs\pending.xml.bad to WER report because it is missing. Continuing without it... 2011-08-15 10:32:52, Info CBS SQM: Reporting package change completion for package: Package_for_KB976932~31bf3856ad364e35~amd64~~6.1.1.17514, current: Partially Installed, original: Partially Installed, target: Installed, status: 0x80070490, failure source: CBS Other, failure details: "(null)", client id: SP Coordinater Engine, initiated offline: False, execution sequence: 517, first merged sequence: 517 2011-08-15 10:32:52, Info CBS SQM: Upload requested for report: PackageChangeEnd_Package_for_KB976932~31bf3856ad364e35~amd64~~6.1.1.17514, session id: 101457924, sample type: Standard 2011-08-15 10:32:52, Info CBS SQM: Ignoring upload request because the sample type is not enabled: Standard I have downloaded the service pack and ran it from the EXE, I have installed it from Windows Update, I have ran all the "troubleshooting" trouble shots I could find. Nothing has worked so far. Any advice would be appreciated.

  Read the article

• No internet through a web browser but Skype still works

  - by kim3er

  We get our office broadband through a BT Business Broadband WiFi router. We have a mixture of macs and windows PC/laptops connecting to it at any one time. All devices are able to connect to the wireless signal with pretty much full signal. However, only two computers (one windows, one os x) are able to consistently connect to the internet. The other three (one windows, two os x), while they can always connect to the wifi, exhibit one of three characteristics. No internet at all. Programs like Skype work, but no internet through a browser. Internet works, but with intermittent lag when switching between different sites. I'm assuming while trying to resolve different addresses. Ignoring point 1 for moment, my gut is telling me DNS. It is an up to 20MB line that usually gets to between 13MB and 15MB downstream. The router is capable of dealing with the amount of wireless devices that we're throwing at it. Has anyone got any suggestions for how I might further diagnose this problem (preferably in OS X)? Rich

  Read the article

• Edit Contact code worked in 1.6 but doesn't work on Droid 2.1?

  - by user225405

  Hi All, I had some fairly simple code in my app to invoke Edit Contact activity on a known good contact index that worked in Android 1.6 but is broken for me now in Android 2.1 on the Droid. I built a sample activity/app 'EdCon' to show this: package com.jbh; import android.app.Activity; import android.content.Intent; import android.net.Uri; import android.os.Bundle; public class EdCon extends Activity { /** Called when the activity is first created. */ @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.main); // Build an intent to edit a known good contact index Intent i; i = new Intent(Intent.ACTION_EDIT); i.setData(Uri.parse("content://contacts/people/10")); startActivity(i); } } When I run this on my G1 running 1.6 it works as expected i.e. brings up the Edit Contact screen for the known index and then I can hit BACK to return to "Hello World, EdCon". When I run this on the Droid under 2.1 I get the following: 05-07 15:35:57.787: INFO/ActivityManager(1013): Starting activity: Intent { act=android.intent.action.MAIN cat=[android.intent.category.LAUNCHER] flg=0x10000000 cmp=com.jbh/.EdCon } 05-07 15:35:57.826: DEBUG/AndroidRuntime(13780): Shutting down VM 05-07 15:35:57.826: DEBUG/dalvikvm(13780): DestroyJavaVM waiting for non-daemon threads to exit 05-07 15:35:57.928: DEBUG/dalvikvm(13780): DestroyJavaVM shutting VM down 05-07 15:35:57.928: DEBUG/dalvikvm(13780): HeapWorker thread shutting down 05-07 15:35:57.928: DEBUG/dalvikvm(13780): HeapWorker thread has shut down 05-07 15:35:57.928: DEBUG/jdwp(13780): JDWP shutting down net... 05-07 15:35:57.928: DEBUG/jdwp(13780): Got wake-up signal, bailing out of select 05-07 15:35:57.928: INFO/dalvikvm(13780): Debugger has detached; object registry had 1 entries 05-07 15:35:57.928: DEBUG/dalvikvm(13780): VM cleaning up 05-07 15:35:57.935: INFO/ActivityManager(1013): Start proc com.jbh for activity com.jbh/.EdCon: pid=13802 uid=10052 gids={1015} 05-07 15:35:57.967: ERROR/AndroidRuntime(13780): ERROR: thread attach failed 05-07 15:35:58.053: INFO/ActivityThread(13792): Publishing provider com.android.vending.SuggestionsProvider: com.android.vending.SuggestionsProvider 05-07 15:35:58.154: INFO/dalvikvm(13802): Debugger thread not active, ignoring DDM send (t=0x41504e4d l=38) 05-07 15:35:58.209: DEBUG/dalvikvm(13780): LinearAlloc 0x0 used 639500 of 5242880 (12%) 05-07 15:35:58.365: INFO/dalvikvm(13802): Debugger thread not active, ignoring DDM send (t=0x41504e4d l=18) 05-07 15:35:58.639: INFO/ActivityManager(1013): Starting activity: Intent { act=android.intent.action.EDIT dat=content://contacts/people/10 cmp=com.android.contacts/.ui.EditContactActivity } 05-07 15:35:58.975: DEBUG/dalvikvm(13137): GC freed 2902 objects / 166768 bytes in 61ms 05-07 15:35:59.100: DEBUG/vending(13792): com.android.vending.LocalDbSyncService.run(): Syncing local DB with package manager... 05-07 15:35:59.100: DEBUG/vending(13792): com.android.vending.LocalDbSyncService.syncLocalDbWithPackageManager(): No INSTALLING or UNINSTALLING assets. 05-07 15:35:59.115: INFO/ActivityManager(1013): Displayed activity com.android.contacts/.ui.EditContactActivity: 387 ms (total 1296 ms) 05-07 15:35:59.185: DEBUG/Sources(13137): Creating external source for type=com.facebook.auth.login, packageName=com.facebook.katana 05-07 15:35:59.225: DEBUG/vending(13792): com.android.vending.LocalDbSyncService.run(): Syncing done. 05-07 15:35:59.232: WARN/dalvikvm(13137): threadid=27: thread exiting with uncaught exception (group=0x4001b180) 05-07 15:35:59.232: ERROR/AndroidRuntime(13137): Uncaught handler: thread AsyncTask #1 exiting due to uncaught exception 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): java.lang.RuntimeException: An error occured while executing doInBackground() 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.os.AsyncTask$3.done(AsyncTask.java:200) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at java.util.concurrent.FutureTask$Sync.innerSetException(FutureTask.java:273) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at java.util.concurrent.FutureTask.setException(FutureTask.java:124) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at java.util.concurrent.FutureTask$Sync.innerRun(FutureTask.java:307) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at java.util.concurrent.FutureTask.run(FutureTask.java:137) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at java.util.concurrent.ThreadPoolExecutor.runWorker(ThreadPoolExecutor.java:1068) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:561) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at java.lang.Thread.run(Thread.java:1096) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): Caused by: android.database.sqlite.SQLiteException: no such column: raw_contact_id: , while compiling: SELECT account_name, account_type, sourceid, version, dirty, data_id, res_package, mimetype, data1, data2, data3, data4, data5, data6, data7, data8, data9, data10, data11, data12, data13, data14, data15, data_sync1, data_sync2, data_sync3, data_sync4, _id, is_primary, is_super_primary, data_version, group_sourceid, sync1, sync2, sync3, sync4, deleted, contact_id, starred, is_restricted FROM contact_entities_view WHERE (1) AND (raw_contact_id=10) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.database.sqlite.SQLiteProgram.native_compile(Native Method) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.database.sqlite.SQLiteProgram.compile(SQLiteProgram.java:110) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.database.sqlite.SQLiteProgram.(SQLiteProgram.java:59) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.database.sqlite.SQLiteQuery.(SQLiteQuery.java:49) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.database.sqlite.SQLiteDirectCursorDriver.query(SQLiteDirectCursorDriver.java:49) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.database.sqlite.SQLiteDatabase.rawQueryWithFactory(SQLiteDatabase.java:1221) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.database.sqlite.SQLiteQueryBuilder.query(SQLiteQueryBuilder.java:316) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at com.android.providers.contacts.ContactsProvider2.query(ContactsProvider2.java:3850) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at com.android.providers.contacts.ContactsProvider2.query(ContactsProvider2.java:3840) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at com.android.providers.contacts.ContactsProvider2$RawContactsEntityIterator.(ContactsProvider2.java:4498) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at com.android.providers.contacts.ContactsProvider2.queryEntities(ContactsProvider2.java:4751) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.content.ContentProvider$Transport.queryEntities(ContentProvider.java:140) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.content.ContentProviderClient.queryEntities(ContentProviderClient.java:98) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.content.ContentResolver.queryEntities(ContentResolver.java:296) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at com.android.contacts.model.EntitySet.fromQuery(EntitySet.java:72) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at com.android.contacts.ui.EditContactActivity$QueryEntitiesTask.doInBackground(EditContactActivity.java:191) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at com.android.contacts.ui.EditContactActivity$QueryEntitiesTask.doInBackground(EditContactActivity.java:154) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at com.android.contacts.util.WeakAsyncTask.doInBackground(WeakAsyncTask.java:45) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at android.os.AsyncTask$2.call(AsyncTask.java:185) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): at java.util.concurrent.FutureTask$Sync.innerRun(FutureTask.java:305) 05-07 15:35:59.295: ERROR/AndroidRuntime(13137): ... 4 more 05-07 15:35:59.303: INFO/Process(1013): Sending signal. PID: 13137 SIG: 3 05-07 15:35:59.303: INFO/dalvikvm(13137): threadid=7: reacting to signal 3 05-07 15:35:59.303: ERROR/dalvikvm(13137): Unable to open stack trace file '/data/anr/traces.txt': Permission denied 05-07 15:35:59.506: INFO/DumpStateReceiver(1013): Added state dump to 1 crashes 05-07 15:36:07.053: DEBUG/dalvikvm(12901): GC freed 389 objects / 25056 bytes in 145ms 05-07 15:36:17.287: DEBUG/dalvikvm(11649): GC freed 154 objects / 6816 bytes in 136ms 05-07 15:36:22.365: DEBUG/dalvikvm(13574): GC freed 348 objects / 67848 bytes in 112ms 05-07 15:36:27.451: DEBUG/dalvikvm(11836): GC freed 267 objects / 17432 bytes in 65ms 05-07 15:36:32.553: DEBUG/dalvikvm(12757): GC freed 1888 objects / 92440 bytes in 67ms 05-07 15:36:38.803: INFO/power(1013): * set_screen_state 0 05-07 15:36:38.813: DEBUG/SurfaceFlinger(1013): About to give-up screen, flinger = 0x114c30 05-07 15:36:38.826: DEBUG/Sensors(1013): using accelerometer (name=accelerometer) 05-07 15:36:38.834: DEBUG/PhoneWindow(13137): couldn't save which view has focus because the focused view android.widget.ScrollView@44883558 has no id. 05-07 15:36:38.865: DEBUG/WifiService(1013): ACTION_SCREEN_OFF 05-07 15:36:38.889: DEBUG/WifiService(1013): setting ACTION_DEVICE_IDLE timer for 900000ms 05-07 15:36:44.107: DEBUG/dalvikvm(1013): GC freed 7351 objects / 521440 bytes in 130ms 05-07 15:36:49.373: DEBUG/dalvikvm(13553): GC freed 321 objects / 12056 bytes in 102ms The no such column: raw_contact_id: looks like the issue but I'm not sure how or why that would happen or what it means. Any help appreciated! [email protected]

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >