Search Results

Search found 7954 results on 319 pages for 'behavior driven developme'.

Page 282/319 | < Previous Page | 278 279 280 281 282 283 284 285 286 287 288 289  | Next Page >

• Is my Cisco switch port bad?

  - by ewwhite

  I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

  Read the article

• change owner/uid of mount point upon mount

  - by Shiplu

  The scenario is like this. Bob has a computer. It crashed. Now he only has the hdd. The hdd is in ext3 format. He go to his office and told the sys admin John to mount this hdd and put the mount point in his home directory. John used the following fstab entries. # Bobs harddisk /media/TAPE4/Bobs-hdd.img /home/bob/myhdd/windows ntfs ro,loop,offset=32256 0 0 /media/TAPE4/Bobs-hdd.img /home/bob/myhdd/linux ext3 ro,loop,offset=14048810496 0 0 /media/TAPE4/Bobs-hdd.img /home/bob/myhdd/extra ntfs ro,loop,offset=28015335936 0 0 Bob was happy. He could access his old extra and windows. Specially the Documents and Settings in windows was helpful for him. But he found a problem. He is a web developer and all his websites are in linux/home/bob/public_html directory. When he tried to access that public_html directory he got permission_denied. He executed ls -lh he saw this. drwxr-xr-x 2 john john 4.0K Nov 9 2011 Desktop drwxr-xr-x 3 john john 4.0K Aug 12 2011 Documents drwxr-xr-x 3 john john 4.0K Aug 21 2011 public_html He contacted John thinking he might be mistakenly did this. But John couldn't find a way why this happend? Then one thing came into his mind file system hardly store username. They store uids. So he executed ls -ln drwxr-xr-x 2 1000 1000 4096 Nov 9 2011 Desktop drwxr-xr-x 3 1000 1000 4096 Aug 12 2011 Documents drwxr-xr-x 3 1000 1000 4096 Aug 21 2011 public_html John thinks 1000 is the first uid on a linux system. As he is the admin of the current system. He created his account first. so Johns uid was 1000. Bob also setup his private system and crated his account first. So Bobs uid was 1000 too. So thats an expected behavior. But problem remains. How can Bob access those websites in public_html?

  Read the article

• Coldfusion 8 Application Crashes Under Heavy Load

  - by KM01

  Hello, We have a CF8 app that runs for 20-25 minutes before crashing under heavy load ~ 1200 users. This load is generated by our load testing tool: 1200 users ramped up in 5 mins (approx behavior of our users), running for an hour. We have this app on Solaris 10, Apache 2, JRun 4 and Oracle 10g. Java version is 1.6. During the initial load tests, the thread dumps pointed to monitor deadlocks that pointed to sessions. "jrpp-173": waiting to lock monitor 0x019fdc60 (object 0x6b893530, a java.util.Hashtable), which is held by "scheduler-1" "scheduler-1": waiting to lock monitor 0x026c3ce0 (object 0x6abe2f20, a coldfusion.monitor.memory.SessionMemoryMonitor$TopMemoryUsedSessions), which is held by "jrpp-167" "jrpp-167": waiting to lock monitor 0x019fdc60 (object 0x6b893530, a java.util.Hashtable), which is held by "scheduler-1" We increased the number of sessions relative to the number of CPUs (48 simultaneous threads against 32 CPUs), and the deadlock went away. While varying the simultaneous threads helped a little bit in terms of response time, the CF server still tanked in 20-25 minutes during all of these tests. We ran more thread dumps, and saw a thread locking a monitor, for e.g.: "jrpp-475" prio=3 tid=0x02230800 nid=0x2c5 runnable [0x4397d000] java.lang.Thread.State: RUNNABLE at java.util.HashMap.getEntry(HashMap.java:347) at java.util.HashMap.containsKey(HashMap.java:335) at java.util.HashSet.contains(HashSet.java:184) at coldfusion.monitor.memory.MemoryTracker.onAddObject(MemoryTracker.java:124) at coldfusion.monitor.memory.MemoryTrackerProxy.onReplaceValue(MemoryTrackerProxy.java:598) at coldfusion.monitor.memory.MemoryTrackerProxy.onPut(MemoryTrackerProxy.java:510) at coldfusion.util.CaseInsensitiveMap.put(CaseInsensitiveMap.java:250) at coldfusion.util.FastHashtable.put(FastHashtable.java:43) - locked <0x6f7e1a78> (a coldfusion.runtime.Struct) at coldfusion.runtime.CfJspPage._arrayset(CfJspPage.java:1027) at coldfusion.runtime.CfJspPage._arraySetAt(CfJspPage.java:2117) at cfvalidation2ecfc1052964961$funcSETUSERAUDITDATA.runFunction(/app/docs/apply/cfcs/validation.cfc:377) As you see in the last line above there were several references CFMs and CFCs, and the lines have "cflock" tags, which were scoped to the "application." We (the dev team) then changed them to be scoped to a "name". After more load tests, there is no locking going on and there no deadlocks, but now the application tanks in 7-10 minutes. We've gotten system, network and DB reports from the respective admins, and they are not being taxed; even watched the server stats with server monitor, top, prstat, ran sar reports, etc. So we believe it is an issue with the CF server or maybe the JVM. I am running out of ideas as to what else we can try. Disclaimer: I am not a CF developer or Admin. I am just running the load test, analyzing the reports, threads etc, and sharing the results with the dev and admin teams, and trying the next change, and so on. So far no dice. Has anyone run into something similar? How did you go about diagnosing and troubleshooting? All thoughts and pointers welcome. Thank you for your time! KM

  Read the article

• DLINK WBR-1310B Wireless Router seems to hang...

  - by Ira Baxter

  I have a brand new DLINK-1310B Wireless Router (box never before opened, although I bought it at the neighborhood computer junk store). I am using it at home (and in fact am using it at this instant from a wireless laptop). When operative, I can ping it at 192.168.0.1, and I can log into it from the PC attached to it by LAN and from the wireless PC at //192.168.0.1. In the course of the day since I've installed, it seems to have locked up 3 times. Each time the symptoms are my web browser (or other IP service, e.g., POP3) stops with a "No internet connection" error. Attempts to contact the router via 192.168.0.1 get no reaction, from either the wireless laptop or from the hardwired PC sitting next to it. It doesn't respond to pings to that address either. Power cycling the router fixes it. I've seen discussion in other questions about aging cheap electronics. Its too new to be aged. Anybody else seen this behavior with a DLINK-1310? Or do I just need to exchange it for another and try again? (I hate rolling dice, I bought the DLINK because a previous Linksys died of apparant heating problems, how many do I have to cycle through before I get something that works and is long-term stable?). Remarkably, nobody talks about how much software is in a router. Is the stuff just buggy? EDIT: Happened again, while I was working on the wireless Vista laptop. (Seems like once an hour?) I was a little more careful this time. The wireless laptop can ping it. It can't get the login screen. I visited the LAN-connected PC (takes me a minute to walk from the laptop to the PC at the other end of the house), and attempted to visit a random web page. Surprise, that worked! And, now, after a minute walking back to the laptop, I can reconnect the wireless laptop, and get to the login page from it. Strange the time/date has been reset back to 2002. (I'll swear I set it and saved the system configuration after updating the firmware; it made me redo every other bit of reconfiguration again). Is there something funny about wireless leases expiring? The router says the leases it is handing out are good for 180 minutes, and the delay-to-inaccessible was only about an hour. The DSL connection seems to have a 10 minute lease.

  Read the article

• Linux per-process resource limits - a deep Red Hat Mystery

  - by BobBanana

  I have my own multithreaded C program which scales in speed smoothly with the number of CPU cores.. I can run it with 1, 2, 3, etc threads and get linear speedup.. up to about 5.5x speed on a 6-core CPU on a Ubuntu Linux box. I had an opportunity to run the program on a very high end Sunfire x4450 with 4 quad-core Xeon processors, running Red Hat Enterprise Linux. I was eagerly anticipating seeing how fast the 16 cores could run my program with 16 threads.. But it runs at the same speed as just TWO threads! Much hair-pulling and debugging later, I see that my program really is creating all the threads, they really are running simultaneously, but the threads themselves are slower than they should be. 2 threads runs about 1.7x faster than 1, but 3, 4, 8, 10, 16 threads all run at just net 1.9x! I can see all the threads are running (not stalled or sleeping), they're just slow. To check that the HARDWARE wasn't at fault, I ran SIXTEEN copies of my program independently, simultaneously. They all ran at full speed. There really are 16 cores and they really do run at full speed and there really is enough RAM (in fact this machine has 64GB, and I only use 1GB per process). So, my question is if there's some OPERATING SYSTEM explanation, perhaps some per-process resource limit which automatically scales back thread scheduling to keep one process from hogging the machine. Clues are: My program does not access the disk or network. It's CPU limited. Its speed scales linearly on a single CPU box in Ubuntu Linux with a hexacore i7 for 1-6 threads. 6 threads is effectively 6x speedup. My program never runs faster than 2x speedup on this 16 core Sunfire Xeon box, for any number of threads from 2-16. Running 16 copies of my program single threaded runs perfectly, all 16 running at once at full speed. top shows 1600% of CPUs allocated. /proc/cpuinfo shows all 16 cores running at full 2.9GHz speed (not low frequency idle speed of 1.6GHz) There's 48GB of RAM free, it is not swapping. What's happening? Is there some process CPU limit policy? How could I measure it if so? What else could explain this behavior? Thanks for your ideas to solve this, the Great Xeon Slowdown Mystery of 2010!

  Read the article

• Wireless traffic stops when downloading large files at high speed: packets lost (Linksys WRT120N router)

  - by Torious

  The problem Note: First I'd like to understand WHY this is happening. Ofcourse, a solution would be nice too. :) When downloading a large file over HTTP at high-speeds, my wireless traffic basically stops: I can't open webpages and the download itself pauses. It pauses pretty much immediately after starting it; sometimes at 800 KB, sometimes at a few MB. After some time, the download (and other traffic) resumes, but the problem keeps reoccurring during the same download. The problem does not occur when using a wired connection through the same router (Linskys WRT120N). Also note that the connection is not dropped when this happens. It's just that the traffic stops and I can't browse to web pages, etc. (SYN packets are sent but nothing is received, etc.) Inspection with Wireshark shows that the following happens: Server sends data packets which are acknowledged by client Server sends a packet, but SEQ indicates some packets were lost (6 packets in one occurrence). Server sends a few more packets and client acknowledges these using "selective acknowledgement" Server stops sending data for a while (since the lost packets were not acknowledged or the router stops forwarding them?) Eventually, server does a "retransmission" and traffic resumes as normal. This all seems normal behavior to me when packet loss occurs. It's the consistent packet loss throughout a large, high-speed download that puzzles me. What might cause this? My own idea is the following: My internet is pretty fast (100 mbps), so when starting a large-file download, the router buffers the incoming data (since wireless introduces some slight delay / lower speed, in part due to other networks), but the buffer overflows and the router drops packets to regulate traffic (and because it has no choice). But how could that happen? Doesn't the TCP window size limit the amount of data that can go unacknowledged? So how can the router's buffer overflow if there can only be like 64 KB waiting to be acknowledged? Note: I've disabled TCP window scaling and dynamic window size through netsh options, in an attempt to fix this, but it doesn't seem to matter. Also, Wireshark shows a pattern of the server sending 2 packets (of 1514 bytes) and the client sending an ACK, so does that rule out a possible buffer overflow? And a few more subsequent packets are received... I'm at a loss here. Thanks for any insights. Things that are (probably) NOT the cause / I have experimented with The browser Various TCP options in Windows 7 (netsh etc.) Router settings such as MTU, beacon interval, UPnP, ...

  Read the article

• What is it that kills laptop batteries?

  - by Mala

  There are many superstitions on what you must never do lest your battery become worthless - and by worthless I mean hold about 16 - 24 seconds of charge. This has happened to every laptop I have ever owned, and I just got a new one, so please help me sort out fact from fiction. Here are some of the things I've heard: Do not keep your laptop fully charged. You must run it completely down every so often. Do not use your laptop plugged in to the wall. Only plug it in when it needs charge. If you will not be using your laptop for a long period of time, don't leave it at full charge. Do not leave your laptop running 24/7. The first two I know to be complete fiction: this was true of old batteries such as you might have had in an iPod in 2003, but modern batteries function better when kept at or near full charge. Devices even have circuitry to prevent you from completely depleting your battery, as this is dangerous. The third point sounds probable, and I'd be interested to know if it was true. However, it doesn't really apply to me because I'm not really the type to leave my laptop alone for a day, much less a "long period of time" The fourth seems most likely of the above, but only because of causality: I have always done this, and my batteries have always crapped out on me. I've generally treated a laptop like a desktop with a battery backup, and that I can move from one room to another if necessary. The fact that my batteries tend to last less than 30 seconds has further entrenched this behavior. Should I be trying to break this habit? Are there any other things that ruin laptop batteries? I love that I can actually use my new laptop unplugged :) I'd like to keep it that way. Update: Additional question: If the computer will be used for an extended period of time plugged in, does it make sense to remove the battery first? Update 2: I know people with laptops older than mine, who actively use their laptops as much as I do, and their batteries still hold about an hours' charge while mine holds less than 30 seconds, hence my belief that something I'm doing kills them.

  Read the article

• Can Vagrant point to a directory of Puppet manifests for execution?

  - by SeligkeitIstInGott

  I am using Vagrant to jump start some initial Puppet config and am confused on how to include/run multiple manifests (other than just site.pp) in the puppet execution workflow without making the extra manifests into modules and including them that way. In the puppet manifests directory that I point Vagrant to (see below) I have two manifests that I want executed: site.pp and hierasetup.pp. config.vm.provision "puppet" do |puppet| puppet.manifests_path = "puppet_files/manifests" puppet.module_path = "puppet_files/modules" puppet.manifest_file = "site.pp" puppet.options = "--verbose --debug" end Currently I am having site.pp be the manifest that calls hierasetup.pp. My site.pp looks like this: File { owner => 'root', group => 'root', mode => '0644', } import "hierasetup.pp" include jboss But I get this error about the deprecation of "import": Warning: The use of 'import' is deprecated at /tmp/vagrant-puppet-1/manifests/site.pp:33. See http://links.puppetlabs.com/puppet-import-deprecation (at grammar.ra:610:in `_reduce_190') According to the referenced URL under "Things to try instead" it says "To keep your node definitions in separate files, specify a directory as your main manifest". Further this puppet doc on main manifests says: "Recommended: If you’re using the main manifest heavily instead of relying on an ENC, consider changing the manifest setting to $confdir/manifests. This lets you split up your top-level code into multiple files while avoiding the import keyword. It will also match the behavior of simple environments." It appears that Puppet can reference an entire directory instead of just a specific manifest file, such that I would expect that Vagrant would make a provision for this and allow me to drop the "puppet.manifest_file = "site.pp" line and point to the parent directory instead in which all the *.pp files there will be executed. However removing that line in Vagrant merely generates a complaint about an expected "default.pp" in its stead: puppet provisioner: * The configured Puppet manifest is missing. Please specify a path to an existing manifest: /some/path/puppet_files/manifests/default.pp So: Firstly, do I understand the "new" (non-import) way of calling multiple manifests correctly, in that a directory is to be pointed to in which all the *.pp files inside it will be executed? And secondly, has Vagrant "caught up" with this new change to accommodate the referencing of directories in conjunction with Puppet's deprecation of "import"? Update: Thanks to Shane the issue with #2 (Vagrant's code not being caught up to allow pointing to puppet manifest directories) was reported on Vagrant's GitHub issue tracker site and has since been patched: https://github.com/mitchellh/vagrant/issues/4169

  Read the article

• How to setup ssh's umask for all type of connections

  - by Unode

  I've been searching for a way to setup OpenSSH's umask to 0027 in a consistent way across all connection types. By connection types I'm referring to: sftp scp ssh hostname ssh hostname program The difference between 3. and 4. is that the former starts a shell which usually reads the /etc/profile information while the latter doesn't. In addition by reading this post I've became aware of the -u option that is present in newer versions of OpenSSH. However this doesn't work. I must also add that /etc/profile now includes umask 0027. Going point by point: sftp - Setting -u 0027 in sshd_config as mentioned here, is not enough. If I don't set this parameter, sftp uses by default umask 0022. This means that if I have the two files: -rwxrwxrwx 1 user user 0 2011-01-29 02:04 execute -rw-rw-rw- 1 user user 0 2011-01-29 02:04 read-write When I use sftp to put them in the destination machine I actually get: -rwxr-xr-x 1 user user 0 2011-01-29 02:04 execute -rw-r--r-- 1 user user 0 2011-01-29 02:04 read-write However when I set -u 0027 on sshd_config of the destination machine I actually get: -rwxr--r-- 1 user user 0 2011-01-29 02:04 execute -rw-r--r-- 1 user user 0 2011-01-29 02:04 read-write which is not expected, since it should actually be: -rwxr-x--- 1 user user 0 2011-01-29 02:04 execute -rw-r----- 1 user user 0 2011-01-29 02:04 read-write Anyone understands why this happens? scp - Independently of what is setup for sftp, permissions are always umask 0022. I currently have no idea how to alter this. ssh hostname - no problem here since the shell reads /etc/profile by default which means umask 0027 in the current setup. ssh hostname program - same situation as scp. In sum, setting umask on sftp alters the result but not as it should, ssh hostname works as expected reading /etc/profile and both scp and ssh hostname program seem to have umask 0022 hardcoded somewhere. Any insight on any of the above points is welcome. EDIT: I would like to avoid patches that require manually compiling openssh. The system is running Ubuntu Server 10.04.01 (lucid) LTS with openssh packages from maverick. Answer: As indicated by poige, using pam_umask did the trick. The exact changes were: Lines added to /etc/pam.d/sshd: # Setting UMASK for all ssh based connections (ssh, sftp, scp) session optional pam_umask.so umask=0027 Also, in order to affect all login shells regardless of if they source /etc/profile or not, the same lines were also added to /etc/pam.d/login. EDIT: After some of the comments I retested this issue. At least in Ubuntu (where I tested) it seems that if the user has a different umask set in their shell's init files (.bashrc, .zshrc,...), the PAM umask is ignored and the user defined umask used instead. Changes in /etc/profile did't affect the outcome unless the user explicitly sources those changes in the init files. It is unclear at this point if this behavior happens in all distros.

  Read the article

• Why can host and nslookup resolve a name but dig cannot?

  - by musashiXXX

  Can anyone tell me why this is happening? I can resolve a hostname using host and/or nslookup but forward lookups do not work with dig; reverse lookups do: musashixxx@box:~$ host someserver someserver.somenet.internal has address 192.168.0.252 musashixxx@box:~$ host 192.168.0.252 252.0.168.192.in-addr.arpa domain name pointer someserver.somenet.internal. musashixxx@box:~$ nslookup someserver Server: 192.168.0.253 Address: 192.168.0.253#53 Name: someserver.somenet.internal Address: 192.168.0.252 musashixxx@box:~$ nslookup 192.168.0.252 Server: 192.168.0.253 Address: 192.168.0.253#53 252.0.168.192.in-addr.arpa name = someserver.somenet.internal. musashixxx@box:~$ dig someserver ; <<>> DiG 9.8.1-P1 <<>> someserver ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 55306 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;someserver. IN A ;; Query time: 0 msec ;; SERVER: 192.168.0.253#53(192.168.0.253) ;; WHEN: Wed Oct 3 15:47:38 2012 ;; MSG SIZE rcvd: 27 musashixxx@box:~$ dig -x 192.168.0.252 ; <<>> DiG 9.8.1-P1 <<>> -x 192.168.0.252 ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 28126 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;252.0.168.192.in-addr.arpa. IN PTR ;; ANSWER SECTION: 252.0.168.192.in-addr.arpa. 3600 IN PTR someserver.somenet.internal. ;; Query time: 0 msec ;; SERVER: 192.168.0.253#53(192.168.0.253) ;; WHEN: Wed Oct 3 15:49:11 2012 ;; MSG SIZE rcvd: 86 Here's what my resolv.conf looks like: nameserver 192.168.0.253 search somenet.internal Is this behavior normal? Any thoughts?

  Read the article

• Weird IIS with Windows Authentication + IE problem

  - by Paulius Maruška

  I have a website running on IIS and using Windows Authentication. All users that are configured to get access to the site are form a AD domain (not local users). In the properties of a Website, I have set to use the AD domain as the realm. Now, when using Firefox, Safari or Chrome - Everything is fine. When the user tries to open the site, he get's the login box. he enters simply "username" and "password" (let's pretend that it's an actual login and password :P) and he get's into the site. When using IE, however, things get nasty. When the user tries to open the site - he get's the login box. User enters the "username" and "password" again, but those get rejected! And when the second time login box pops up - it has the username filled in as "web-server-domain-name\username" which is wrong, because web-server-domain-name is not the domain where all users reside (it's "ad-domain"). I've spent days trying to figure out what's going on... Note, that if I manually enter "ad-domain\username" - I get accepted into the site without problems. So, my guess is that IE sends wrong username if domain is not specified. Anyway, IE is the only browser that triggers this behavior! Is it possible to do a server-side fix? Maybe it's possible to somehow auto-map the users to AD users? If it's not solvable server-side - is there a client-side fix for this? Thank you. PS: I'm more of a programmer than a sys-admin, so configuring servers isn't the strong side of mine... :P UPDATE: @Evan: Yes, "Digest authentication for Windows domain servers" is also enabled. @Eric: IIS version is 6.0. The authentication methods enabled are: Integrated and digest - all other methods are disabled. As for the security log. I looked at it, when doing "username" and "password" login in Chrome/Firefox and when doing "ad-domain\username" and "password" login from IE - the generated log messages are the same (I see no difference, anyway). When entering "username" and "password" I don't see any errors in the security (or any other) log, so can't tell what method it's trying to use. UPDATE 2: As suggested by Eric in the comments - I played around with Fiddler... While playing with it, I noticed, that when "username" and "password" is entered in FF and IE - the "Authorization" header value (encrypted) sent by IE is longer (almost two times) than one sent by FF. I tried to disable Windows Integrated authentication and only leave the Digest enabled - that fixed the problem (meaning, IE used the right realm just like other browsers), but that caused bazillion other problems with my site, because with Digest - user impersonation on the server doesn't work (that causes problems, when connecting to database etc). Any ideas?

  Read the article

• libreadline history lines combine

  - by jettero

  This has been driving me crazy for about three years. I don't know how to fully describe the problem, but I think I can finally describe a way to recreate it. Your milage may vary. I have a mixture of ubuntu server and desktop machines of various versions and a few gentoo machines with various states of disrepair. They all seem to kindof do their own thing, although with similarities. Try this and let me know if you see the same thing. pop open two xterms (TERM=xterm) resize one so they're not the same issue screen -R test1 in one (TERM=screen) and screen -x test1 in the other hooray, typing in one shows up in the other; although notice that their different size produces artifacts and things issue a couple commands in your shell hit ^AF in the one that doesn't fit quite right, now it fits!! scroll back over the history a little goto 6 Eventually you'll notice a couple history lines combine. If you don't, then it's something unique to my setup, which spans various distributions and computers; so that's a confusing concept to me. If you see the thing I'm seeing then this: bash$ ls -al bash$ ps auxfw becomes this: bash$ ls -al; ps auxfw It doesn't happen every time. I have to really play with it — unless I don't want it to happen, then it always does. On some systems (or combinations), I get a line separator like the example above. On some systems, I do not. That I get the line separator on some systems seems to indicate to me that bash supports this behavior. Its history is entirely handled by libreadline and after perusing (ie, carefully reading) the man pages, I couldn't find a single readline setting for combining two history lines. Nor can I find anything in the bash manpage. So, how can I invoke this on purpose? Or, if I can't do that, how can I disable it completely? I would take either answer as a solution. Currently, I only see it when I don't want it.

  Read the article

• WiFi signal is lost every 3 minutes

  - by Software Monkey

  For several weeks now my Android phone has been losing it's WiFi signal momentarily, typically at about 3 minute intervals (about 3 minutes, 1.5 seconds) and occasionally at some longer interval that always seems to be just over 3 minutes. This causes an interruption of several seconds while the WiFi connection is re-established and typically fails any kind of download/streaming that is happening, makes web sites "unreachable" and generally makes the phone unusable as a data device due to the frequency. The signal remains down for about a second, but the phone takes a few more seconds to reconnect to the router. This happens regardless of proximity to the router, which otherwise show a very strong signal - usually -40 to -30 dBm or better in the same room, nowhere less than 060 dBm anywhere in the house. Changing channels does not help (I've tried 1, 4, 8 and 9). Nor does turning off the router's guest access. Nor does turning off the 5.0 GHz band. Monitoring the signal on my phone with WiFi analyzer, shows all WiFi signals on all channels drop to nothing when the WiFi connection is lost (there are two other networks on different channels which are strong enough to be relevant, with about 6 others constantly fading in and out). WiFi analyzer shows 3 separate signals for my router, the main 2.4 GHz, the guest 2.4 GHz and the 5.0 GHz. Using WiFi Analyzer on my wife's phone side-by-side shows no change in signal when my phone drops, nor does her phone drop. Monitoring the signal using our laptop, side-by-side likewise shows no signal loss and likewise the laptop does not lose it's WiFi connection. But, at work, the phone seems to not exhibit the same behavior, or, if it does, it's very occasional. Monitoring it all day at work I only saw the signal drop 3 or 4 times. The signal strength of the various networks there is comparatively weak. AT&T were super helpful: "Sorry, we can't help you with WiFi problems. You could try doing a factory reset on your phone". </sarcasm The router is relatively new, but has been working fine with this phone since last Dec. Phone : Motorola Atrix (about 8 months old). Router : Belkin N750 DB (F9K1103 v1 (01C)). Router Firmware: 1.00.46 (2011/10/28 6:37:11). Security : WPA/WPA2-Personal (PSK)

  Read the article

• Switch flooding when bonding interfaces in Linux

  - by John Philips

  +--------+ | Host A | +----+---+ | eth0 (AA:AA:AA:AA:AA:AA) | | +----+-----+ | Switch 1 | (layer2/3) +----+-----+ | +----+-----+ | Switch 2 | +----+-----+ | +----------+----------+ +-------------------------+ Switch 3 +-------------------------+ | +----+-----------+----+ | | | | | | | | | | eth0 (B0:B0:B0:B0:B0:B0) | | eth4 (B4:B4:B4:B4:B4:B4) | | +----+-----------+----+ | | | Host B | | | +----+-----------+----+ | | eth1 (B1:B1:B1:B1:B1:B1) | | eth5 (B5:B5:B5:B5:B5:B5) | | | | | | | | | +------------------------------+ +------------------------------+ Topology overview Host A has a single NIC. Host B has four NICs which are bonded using the balance-alb mode. Both hosts run RHEL 6.0, and both are on the same IPv4 subnet. Traffic analysis Host A is sending data to Host B using some SQL database application. Traffic from Host A to Host B: The source int/MAC is eth0/AA:AA:AA:AA:AA:AA, the destination int/MAC is eth5/B5:B5:B5:B5:B5:B5. Traffic from Host B to Host A: The source int/MAC is eth0/B0:B0:B0:B0:B0:B0, the destination int/MAC is eth0/AA:AA:AA:AA:AA:AA. Once the TCP connection has been established, Host B sends no further frames out eth5. The MAC address of eth5 expires from the bridge tables of both Switch 1 & Switch 2. Switch 1 continues to receive frames from Host A which are destined for B5:B5:B5:B5:B5:B5. Because Switch 1 and Switch 2 no longer have bridge table entries for B5:B5:B5:B5:B5:B5, they flood the frames out all ports on the same VLAN (except for the one it came in on, of course). Reproduce If you ping Host B from a workstation which is connected to either Switch 1 or 2, B5:B5:B5:B5:B5:B5 re-enters the bridge tables and the flooding stops. After five minutes (the default bridge table timeout), flooding resumes. Question It is clear that on Host B, frames arrive on eth5 and exit out eth0. This seems ok as that's what the Linux bonding algorithm is designed to do - balance incoming and outgoing traffic. But since the switch stops receiving frames with the source MAC of eth5, it gets timed out of the bridge table, resulting in flooding. Is this normal? Why aren't any more frames originating from eth5? Is it because there is simply no other traffic going on (the only connection is a single large data transfer from Host A)? I've researched this for a long time and haven't found an answer. Documentation states that no switch changes are necessary when using mode 6 of the Linux interface bonding (balance-alb). Is this behavior occurring because Host B doesn't send any further packets out of eth5, whereas in normal circumstances it's expected that it would? One solution is to setup a cron job which pings Host B to keep the bridge table entries from timing out, but that seems like a dirty hack.

  Read the article

• Problem with several USB devices on Windows XP. How to diagnose USB device?

  - by Lukasz Baran

  Hello All, Recently I've bought some electronic devices (like e.g. Sony Ebook reader PRS-600 or HP PDA IPaq) which are connected to PC using USB ports. These devices have own batteries and they are recharged using USB. However, I am experiencing a problem with Ebook Reader and the similiar thing happens with my PDA (but in this case it's more rare). Sometimes, I am unable to make it start recharging, when it's connected to USB port. The LCD diode on my Reader lights up and the icon in the system tray appears. They both indicate that the device has been connected. However, the device should start recharching and it should appear on Windows XP as a 'explorable' device (just like pendrive it offers some HDDs). None of these happens:( This problem appears on two PCs - desktop and laptop. Both have Windows XP SP3 installed. And what's interesting and surprising to me is the fact that these devices sometimes work without any problems. I mean, I just plug them in and they work properly. Besides that, there are some computers (I have tested a variety of possible conditions) on which the problem does not appear! I am confused and, on the other hand, determined to find out what is the real cause of such strange behavior. Maybe I'm wrong but I always assumed that I'm using deterministic machines, but the described situation makes me feel like I was dreaming:) And that's why I'm asking you here. Are there any tools that could help me diagnose USB ports? Or maybe anyone knows the solution? I have a lot experience with low level programming (mostly from the times of MS-DOS applications), but I'm not an expert when it comes to WinXP technology. If this was a problem with network connection, I would know what to do - I know how to track network traffic, but with USB ports I feel powerless. I have a feeling that the problem may lie in a way WinXP handles USB devices. Personally, I hate auto-discovery and P'n'P features available in Windows. I know that some of may suggest to move to Linux or other *Nix system. Unfortunately, I have to use WinXP in my professional life, so it's rather impossible. Besides that, I don't consider XP as a total disaster. Any help from you will be appreciated!

  Read the article

• How to Remove Extensions From, and Force the Trailing Slash at the End of URLs?

  - by Kronbernkzion

  Example of current file structure: example.com/foo.php example.com/bar.html example.com/directory/ example.com/directory/foo.php example.com/directory/bar.html example.com/cgi-bin/directory/foo.cgi I want to remove HTML, PHP and CGI extensions from, and then force the trailing slash at the end of URLs. So, it could look like this: example.com/foo/ example.com/bar/ example.com/directory/ example.com/directory/foo/ example.com/directory/bar/ example.com/cgi-bin/directory/foo/ I've searched for solution for 17 hours straight and visited more than a few hundred pages on various blogs and forums. I'm not joking. So I think I've done my research. Here is the code that sits in my .htaccess file right now: RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_FILENAME}\.html -f RewriteRule ^(([^/]+/)*[^./]+)/$ $1.html RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !(\.[a-zA-Z0-9]|/)$ RewriteRule (.*)$ /$1/ [R=301,L] As you can see, this code only removes .html (and I'm not very happy with it because I think it could be done a lot simpler). I can remove the extension from PHP files when I rename them to .html through .htaccess, but that's not what I want. I want to remove it straight. This is the first thing I don't know how to do. The second thing is actually very annoying. My .htaccess file with code above, adds .html/ to every string entered after example.com/directory/foo/. So if I enter example.com/directory/foo/bar (obviously /bar doesn't exist since foo is a file), instead of just displaying message that page is not found, it converts it to example.com/directory/foo/bar.html/, then searches for a file for a few seconds and then displays the not found message. This, of course, is bad behavior. So, once again, I need the code in .htaccess to do the following things: Remove .html extension Remove .php extension Remove .cgi extension Force the trailing slash at the end of URLs Requests should behave correctly (no adding trailing slashes or extensions to strings if file or directory doesn't exist on server) Code should be as simple as possible I would very much appreciate any help. And to first person that gives me the solution, I'll send two $50 iTunes Store gift cards for US store. If this offend anyone, I am truly sorry and I apologize. Thanks in advance. And sorry for such a long post.

  Read the article

• Synchronize the same set of files to 2 different locations with 2 different programs for 2 different purposes

  - by Hedgetrimmer

  Because of stupid questionable IT policies at my not-to-be-named place of occupation, I have been (and will be, for the forseeable future) carrying on an external hard drive a unison-synchronized copy of all of my documents and code, including code which resides in some of my "dotfiles" and other code which resides in ~/bin (things I've made are there because ~/bin is in my $PATH) along with some cruft generated (and to be generated) by conscript and its related "giter8" templating system for Scala project boilerplates. Despite this, I do use a symlinking program to store all of my important dotfiles in a subdirectory. Thanks to that somewhat complicated setup, I have resorted to making a directory full of symlinks to every directory (or file, as is the case with stuff under ~/bin) that I want synchronized, and then follow = True is in my unison profile. It happens to be that this collection of odds and ends—plus an automatically-generated text file containing every package installed on my system—is everything under ~ that needs to be backed up to a remote (rsync-over-ssh) host with client-side encryption and signing from GPG. I already believe that duplicity is the most appropriate program to do that. What isn't as clear-cut is how to make duplicity use the exact same set of files when it runs a backup; it would be simple if duplicity would follow symlinks, but it does not and the manpage lists no option for enabling any such behavior. Comparing unison's file selection algorithm to duplicity's, I don't think I can write a program that could compute a ruleset for one program given one for the other. For the record, I would rather not keep the symlinks manually synchronized with duplicity file-selection rules, as they can change thanks to the above-mentioned complications regarding ~/bin. I don't think running duplicity on the external hard disk is such a good idea either; I usually keep that hard disk unmounted and unplugged in case of a power failure or other physical problem with the computer, plus I'm not sure about duplicity's performance given that: the hard disk is NTFS-formatted in order to be useable at my Windows-imprisoned place of occupation. despite being a USB 3.0 disk, my computer has no USB 3.0 ports so it acts as a USB 2.0 disk. How can I have duplicity (or is there a better program that I have overlooked?) back up the exact same set of files that is bidirectionally synchronized with my external hard disk?

  Read the article

• $PATH is driving me nuts

  - by Chris4d

  OK, apologies if this is something dumb, but I'm running out of ideas. Goal: prepend /usr/local/bin to $PATH Problem: $PATH won't do what I want or expect How I got here: I want to start learning to program, so I'm getting comfortable messing around under the hood, but don't have a lot of experience. I installed the fish shell (because it's friendly!) using homebrew and set it as my default shell (under system prefs>users & groups>advanced). At some point, I ran brew doctor to see if my installs were all kosher, and it suggested I move /usr/local/bin to the front of $PATH so that I could use my installation of git rather than the system copy. Fine - but between path_helper and fish, something was happening to $PATH that was out of my control, and I could never get the paths arranged in the right way. Environment: OSX 10.8.2, upgraded from 10.7ish, with xcode and devtools installed, plus x11, homebrew, and fish More info: I've set my user's default shell back to bash, and tried a variety of shells thru terminal.app - bash, fish, sh. I moved /usr/local/bin to the top of /etc/paths but it didn't change anything. I looked thru the various config.fish files and commented out stuff that might mess with $PATH, didn't help. I have the following files in /etc/paths.d/: ./10-homebrew containing /usr/local/bin ./20-fish containing /usr/local/Cellar/fish/1.23.1/bin ./40-XQuartz containing /opt/X11/bin I added set +x to my profile and when I start terminal.app I get: Last login: Mon Oct 1 13:31:06 on ttys000 + '[' -x /usr/libexec/path_helper ']' + eval '/usr/libexec/path_helper -s' ++ /usr/libexec/path_helper -s PATH="/usr/local/bin:/usr/bin:/bin:/usr/sbin:/sbin:/usr/local/Cellar/fish/1.23.1/bin:/opt/X11/bin"; export PATH; + '[' /bin/bash '!=' no ']' + '[' -r /etc/bashrc ']' + . /etc/bashrc ++ '[' -z '\s-\v\$ ' ']' ++ PS1='\h:\W \u\$ ' ++ shopt -s checkwinsize ++ '[' Apple_Terminal == Apple_Terminal ']' ++ '[' -z '' ']' ++ PROMPT_COMMAND='update_terminal_cwd; ' ++ update_terminal_cwd ++ local 'SEARCH= ' ++ local REPLACE=%20 ++ local PWD_URL=file://Chriss-iMac.local/Users/c4 ++ printf '\e]7;%s\a' file://Chriss-iMac.local/Users/c4 Chriss-iMac:~ c4$ So it looks like path_helper runs, but then running echo $PATH nets me /usr/bin:/bin:/usr/sbin:/sbin. So, it looks like path_helper isn't even doing what it's supposed to anymore? I'm sure there is some well-defined behavior here that I don't understand, or I borked something while trying to fix it. Please help!

  Read the article

• High CPU usage - symptoms moving from server to server after bouncing

  - by grt3kl

  First off, I apologize if I didn't include enough information to properly troubleshoot this issue. This sort of thing isn't my specialty, so it is a learning process. If there's something I need to provide, please let me know and I'll be happy to do what I can. The images associated with my question are at the bottom of this post. We are dealing with a clustered environment of four WebLogic 9.2 Java application servers. The cluster utilizes a round-robin load algorithm. Other details include: Java(TM) 2 Runtime Environment, Standard Edition (build 1.5.0_12-b04) BEA JRockit(R) (build R27.4.0-90_CR352234-91983-1.5.0_12-20071115-1605-linux-x86_64, compiled mode) Basically, I started looking at the servers' performance because our customers are seeing lots of lag at various times of the day. Our servers should easily handle the loads they are given, so it's not clear what's going on. Using HP Performance Manager, I generated some graphs that indicate that the CPU usage is completely out of whack. It seems that, at any given point, one or more of the servers has a CPU utilization of over 50%. I know this isn't particularly high, but I would say it is a red flag based on the CPU utilization of the other servers in the WebLogic cluster. Interesting things to note: The high CPU utilization was occurring only on server02 for several weeks. The server crashed (extremely rare; we are not sure if it's related to this) and upon starting it back up, the CPU utilization was normal on all 4 servers. We restarted all 4 managed servers and the application server (on server01) yesterday, on 2/28. As you can see, server03 and server04 picked up the behavior that was seen on server02 before. The CPU utilization is a Java process owned by the application user (appown). The number of transactions is consistent across all servers. It doesn't seem like any one server is actually handling more than another. If anyone has any ideas or can at least point me in the right direction, that would be great. Again, please let me know if there is any additional information I should post. Thanks!

  Read the article

• APC PHP cache size does not exceed 32MB, even though settings allow for more

  - by hardy101

  I am setting up APC (v 3.1.9) on a high-traffic WordPress installation on CentOS 6.0 64 bit. I have figured out many of the quirks with APC, but something is still not quite right. No matter what settings I change, APC never actually caches more than 32MB. I'm trying to bump it up to 256 MB. 32MB is a default amount for apc.shm_size, so I am wondering if it's stuck there somehow. I have run the following echo '2147483648' > /proc/sys/kernel/shmmax to increase my system's shared memory to 2G (half of my 4G box). Then ran ipcs -lm which returns ------ Shared Memory Limits -------- max number of segments = 4096 max seg size (kbytes) = 2097152 max total shared memory (kbytes) = 8388608 min seg size (bytes) = 1 Also made a change in /etc/sysctl.conf then ran sysctl -p to make the settings stick on the server. Rebooted, too, for good measure. In my APC settings, I have mmap enabled (which happens by default in recent versions of APC). php.ini looks like: apc.stat=0 apc.shm_size="256M" apc.max_file_size="10M" apc.mmap_file_mask="/tmp/apc.XXXXXX" apc.ttl="7200" I am aware that mmap mode will ignore references to apc.shm_segments, so I have left it out with default 1. phpinfo() indicates the following about APC: Version 3.1.9 APC Debugging Disabled MMAP Support Enabled MMAP File Mask /tmp/apc.bPS7rB Locking type pthread mutex Locks Serialization Support php Revision $Revision: 308812 $ Build Date Oct 11 2011 22:55:02 Directive Local Value apc.cache_by_default On apc.canonicalize O apc.coredump_unmap Off apc.enable_cli Off apc.enabled On On apc.file_md5 Off apc.file_update_protection 2 apc.filters no value apc.gc_ttl 3600 apc.include_once_override Off apc.lazy_classes Off apc.lazy_functions Off apc.max_file_size 10M apc.mmap_file_mask /tmp/apc.bPS7rB apc.num_files_hint 1000 apc.preload_path no value apc.report_autofilter Off apc.rfc1867 Off apc.rfc1867_freq 0 apc.rfc1867_name APC_UPLOAD_PROGRESS apc.rfc1867_prefix upload_ apc.rfc1867_ttl 3600 apc.serializer default apc.shm_segments 1 apc.shm_size 256M apc.slam_defense On apc.stat Off apc.stat_ctime Off apc.ttl 7200 apc.use_request_time On apc.user_entries_hint 4096 apc.user_ttl 0 apc.write_lock On apc.php reveals the following graph, no matter how long the server runs (cache size fluctuates and hovers at just under 32MB. See image http://i.stack.imgur.com/2bwMa.png You can see that the cache is trying to allocate 256MB, but the brown piece of the pie keeps getting recycled at 32MB. This is confirmed as refreshing the apc.php page shows cached file counts that move up and down (implying that the cache is not holding onto all of its files). Does anyone have an idea of how to get APC to use more than 32 MB for its cache size?? **Note that the identical behavior occurs for eaccelerator, xcache, and APC. I read here: http://www.litespeedtech.com/support/forum/archive/index.php/t-5072.html that suEXEC could cause this problem.

  Read the article

• iTunes and Hulu Playback Choppy and Slow?

  - by Bart Silverstrim

  Specs: Windows XP, latest updates 1.7 ghz Pentium 4 1 gig ram DirectX 9.0c NVIDIA GeForce FX 5200 with 256 meg RAM OpenGL 2.1 The story: Okay, I had an older system laying around that I figured I would try turning into a mini-media system to connect to our TV. I put together a lot of older parts, got it into working order, etc. and hooked it up and voila'...slower, but usable system that displayed to the TV. It could run some things decently. I put in iTunes, it played video okay. Not great, but okay. Played Hulu and since we have a 1Mb download rate, the minimum for their site, there were some choppy moments when watching their shows, but I found that (sadly) changing resolution to 800x600 seemed to help with the issue when running full screen. I downloaded the application called Boxee and installed it. It wouldn't run; apparently the video card in the system supported OpenGL 1.2, and needed at least 1.4. I bought a cheap card, the 5200, with four times the memory in it and support for OpenGL 2.1. Installed, everything seemed fine. iTunes seemed to run fine, the video driver (PNY video card) came with OpenGL 2.1, and Boxee finally ran. I then upgraded to the latest drivers for the video card and ran the DirectX updater from MS. After that, the OpenGL Extension Viewer wouldn't run. It just stayed as an icon in the task bar. Also, any and all videos in iTunes stuttered and went out of sync horribly. Unwatchable. I tried watching Hulu video in Boxee, and it displayed video like it was a series of stills in a very bad powerpoint. Playing straightforward audio-only came through fine, no stutters no hiccups. I tried system restore to roll back updates to pre-directX updates (I thought that seemed to be the time that triggered the weird behavior), no joy. I tried uninstalling and reinstalling the video drivers. I installed updated audio drivers (ensoniq audiopci), nothing helped. I finally wiped the drive last night and tried reinstalling everything and restoring my iTunes content via an import from a backup. Fresh install, no updater on the video card or directx. the problem was still there although I haven't tested Hulu, the iTunes player is still stuttering like crazy if I play video, fine if I play audio. I know the processor isn't high in heft, but with one gig of RAM and the fact that it seemed to do okay before I thought that the problem must be software related. Has anyone else run into this sort of issue and have a solution other than "buy a new computer"? What specs seem to work with video at the low end for you? Right now the system is of little use other than keeping my music library and iTunes apps synced with my iPod.

  Read the article

• RDP exits immediately after connecting to Windows Server 2008 R2

  - by carpat

  Background: I recently got a Windows cloud VPS server. I don't have much experience with server admin (I'm a programmer), and what little I do have is with linux servers. Ever since getting the server I've been having issues with RDP. I can connect about two or three times, after which point I can't connect until one of the tech guys "fixes" it (see below). When I connect, I can stay connected for hours with no problem. When the problem connecting starts, the first time I try to log in, the remote desktop window pops up, starts connecting, and then exits with "Your Remote Desktop session has ended". After that, for about 10-20 minutes if I try to connect again, the connections times out with Remote Desktop can't connect to the computer for one of these reasons: 1) Remote access on the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network then goes back to connecting once and immediately disconnecting. All of the updates are installed. The firewall has been correctly configured to let RDP traffic through. The remote setting is "Allow connections from computers running any version of Remote Desktop". I tried creating a second user, and when I can't connect, I can't connect to that user either. I've tried both soft and hard reboots, neither of which help. I've tried connecting from two different computers (both running Windows 7) from two different networks (work and home), and the behavior is the same. Everything else on the server continues to run fine (IIS-served http pages, Tomcat-served java pages, svn, ping). The "fix" that the tech guys supply is simply logging into the console on their end, after which point I can connnect 2 or 3 times again. The event viewer on the server has "authentication failure" (or something similar) events generated when I attempt to log in and can't. I can't get to the actual event at the moment as I'm currently in the can't connect stage, and waiting for the techs to log in. But when I searched for the event earlier this morning I couldn't find anything useful. Can anyone help?

  Read the article

• IIS6 Log time recording problems

  - by Hafthor

  On three separate occasions on two separate servers at nearly the same times, 6.9 hours seemingly went by without any data being written to the IIS logs, but, on closer inspection, it appears that it was all recorded all at once. Here's the facts as I know them: Windows Server 2003 R2 w/ IIS6 Logging using GMT, server local time GMT-7. Application was still operating and I have SQL data to prove that Time gaps appear in log file, not across two # headers appear at gap Load balancer pings every 30 seconds No caching Here's info on a particular case: an entry appears for 2009-09-21 18:09:27 then #headers the next entry is for 2009-09-22 01:21:54, and so are the next 1600 entries in this log file and 370 in the next log file. about half of the ~2000 entries on 2009-09-22 01:21:54 are load balancer pings (est. at 2/min for 6.9hrs = 828 pings) then entries are recorded as normal. I believe that these events may coincide with me deploying an ASP.NET application update into those machines. Here's some relevant content from the logs in question: ex090921.log line 3684 2009-09-21 17:54:40 GET /ping.aspx - 80 404 0 0 3733 122 0 2009-09-21 17:55:11 GET /ping.aspx - 80 404 0 0 3733 122 0 2009-09-21 17:55:42 GET /ping.aspx - 80 404 0 0 3733 122 0 2009-09-21 17:56:13 GET /ping.aspx - 80 404 0 0 3733 122 0 2009-09-21 17:56:45 GET /ping.aspx - 80 404 0 0 3733 122 0 #Software: Microsoft Internet Information Services 6.0 #Version: 1.0 #Date: 2009-09-21 18:04:37 #Fields: date time cs-method cs-uri-stem cs-uri-query s-port sc-status sc-substatus sc-win32-status sc-bytes cs-bytes time-taken 2009-09-22 01:04:06 GET /ping.aspx - 80 404 0 0 3733 122 3078 2009-09-22 01:04:06 GET /ping.aspx - 80 404 0 0 3733 122 109 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 278 122 3828 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 278 122 0 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 278 122 0 ... continues until line 5449 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 277 122 0 <eof> ex090922.log #Software: Microsoft Internet Information Services 6.0 #Version: 1.0 #Date: 2009-09-22 00:00:16 #Fields: date time cs-method cs-uri-stem cs-uri-query s-port sc-status sc-substatus sc-win32-status sc-bytes cs-bytes time-taken 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 277 122 0 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 277 122 0 ... continues until line 367 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 277 122 0 2009-09-22 01:04:30 GET /ping.aspx - 80 200 0 0 277 122 0 ... back to normal behavior Note the seemingly correct date/time written to the #header of the new log file. Also note that /ping.aspx returned 404 then switched to 200 just as the problem started. I rename the "I'm alive page" so the load balancer stops sending requests to the server while I'm working on it. What you see here is me renaming it back so the load balancer will use the server. So, this problem definitely coincides with me re-enabling the server. Any ideas?

  Read the article

• Repeated requests on our server?

  - by pitty.platsch

  I encountered something strange in the access log of our Apache server which I cannot explain. Requests for webpages that I or my colleagues do from the office's Windows network get repeated by another IP (that we don't know) a couple of seconds later. The user agent repeating our requests is Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 2.0.50727; .NET CLR 3.0.04506.648; .NET CLR 3.5.21022; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729; InfoPath.2) Has anyone an idea? Update: I've got some more information now. The referrer of the replicate is set to the URL I requested before and it's not the exact same request as the protocol version is changed from 'HTTP/1.1' to 'HTTP/1.0'. The IP is not just one, it's just one of a subnet (80.40.134.*). It's just the first request to a resource that's get repeated, so it seems the "spy" is building up some kind of cache of visited places. The repeater is also picky. I tried randomly URLs with different HTTP status codes and different file patterns. 301s and 200s are redone, 404s not. Image extensions seem to be ignored. While doing my tests I discovered that this behavior seems to be common as I found other clients visiting just after the first requests: 66.249.73.184 - - [25/Oct/2012:10:51:33 +0100] "GET /foobar/ HTTP/1.1" 200 10952 "-" "Mediapartners-Google" 50.17.125.180 - - [25/Oct/2012:10:51:33 +0100] "GET /foobar/ HTTP/1.1" 200 41312 "-" "Mozilla/5.0 (compatible; proximic; +http://www.proximic.com/info/spider.php)" I wasn't aware about this practice, so I don't see it that much as a threat anymore. I still want to find out who this is, so any further help is appreciated. I'll try later if this also happens if I query some other server where I have access to the access logs and will update here then.

  Read the article

• I can't delete a directory inside a junctioned directory

  - by Fredy Muñoz

  So this is the deal. A couple of days ago I moved my profile folder C:\Documents and Settings\fmunoz to a different drive D:\fmunoz. Today, I created a directory in my desktop using the point-and-click method: Right-click on an empty space in the desktop Select New Select Folder Leave the default name New Folder and press Enter I tried to delete the folder using the point-and-click method: Right-click the New Folder directory Select Delete After five seconds, I got the following message: --------------------------- Error Deleting File or Folder --------------------------- Cannot delete New Folder: Access is denied. Make sure the disk is not full or write-protected and that the file is not currently in use. --------------------------- Initially I thought that there must be some sort of indexing services locking the directory so I got a list of open files using the TuneUp Process Manager tool but the New Folder directory wasn't there. I double-clicked My Computer, navigated to the desktop directory C:\Documents and Settings\fmunoz\Destkop, tried to delete the New Folder directory using the same point-and-click method described above and got exactly the same message at the same amount of time. In the same window, I navigated to the actual location of the desktop directory D:\fmunoz\Desktop, tried to delete the New Folder directory and this time it worked. I thought that this behavior was due to some special treatment that Windows gives to the desktop or the profile directories so I tried doing the same thing with a different set of directories: Created a folder D:\dummy Created a junction C:\dummy pointing to D:\dummy Created a New Folder directory in C:\dummy Tried to delete New Folder from C:\dummy. Didn't work. Tried to delete New Folder from D:\dummy. It worked. I tried creating the folder in the actual directory rather than the junction directory: Created a New Folder directory in D:\dummy Tried to delete New Folder from C:\dummy. Didn't work. Tried to delete New Folder from D:\dummy. It worked. I also tried using the Delete button instead of using the Delete option of the context menu but it didn't work. When using the Shift+Delete sequence, it works. It also works by using the rd command in the console, but in both cases the deleted directory doesn't goes to the Recycle Bin, which is my intention when using the Delete context menu option or the Delete button.

  Read the article

< Previous Page | 278 279 280 281 282 283 284 285 286 287 288 289  | Next Page >