Search Results

Search found 18209 results on 729 pages for 'loop device'.

Page 290/729 | < Previous Page | 286 287 288 289 290 291 292 293 294 295 296 297  | Next Page >

• Why doesn't the Windows 7 volume mixer remember per-application levels for all applications?

  - by mdives

  If I have the device's master level set to 50, and then lower an application level to 25; Once I close that application and reopen it, the volume levels should persist. The master level should remain at 50 and the application's at 25. This does happen for most applications. However, for one in particular, Napster, it does not. I subscribe to Napster's streaming service. I use the Napster desktop application to connect to that service. Every time that I open the Napster app, I have to adjust the application's volume level down in the volume mixer. When I open the app again after closing it, I have to do the same thing, the volume mixer is not remembering the set level. In fact. The level is reset back to 50, the same level as the device's master level. Has anyone else experienced this, with Napster or any other application? Is there a solution or is this a known issue?

  Read the article

• Change authentication wifi WPA to WEP on Windows 8

  - by Kites

  I use netsh wlan set hostednetwork mode=allow ssid=Kites key=phambaoViet netsh wlan start hostednetwork To share WiFi from LAN network on laptop (Windows 8) to my other device. When I show information netsh wlan show hostednetwork the supported authentication is WPA. My device support authentication WEP only. How can I change the authentication to WEP? Infomation: Interface name: Wi-Fi Driver : Qualcomm Atheros AR9002WB-1NG Wireless Network A dapter Vendor : Qualcomm Atheros Communications Inc. Provider : Microsoft Date : 03/07/2012 Version : 3.0.0.130 INF file : C:\Windows\INF\netathrx.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g 802.11n FIPS 140-2 mode supported : Yes 802.11w Management Frame Protection supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Vendor defined Vendor defined Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP Vendor defined Vendor defined

  Read the article

• How to route to a secondary interface on the same physical ethernet?

  - by sjose3612611

  INTERNET<->(wan)BRIDGED_DEVICE(lan)<->ETH_ROUTER<->LAN Problem: Need to access web server on BRIDGED_DEVICE's LAN from INTERNET via ROUTER (BRIDGED_DEVICE's web server cannot be accessed form INTERNET since it has no Public management IP). Cannot configure bridged device. It has a static IP on its LAN to which its web server binds. Attempt: Create a secondary/alias WAN Interface on ETH_ROUTER (e.g Primary: eth0.1 (for internet access) and Secondary: eth0.2 (for accessing web server on BRIDGED_DEVICE), (No VLANs). eth0.1 has a public IP; eth0.2 has a static private IP in the BRIDGED_DEVICE's subnet (e.g 10.0.X.Y). Iptables on ETH_ROUTER: Added a port forward (DNAT) from eth0.1 to eth0.2: iptables -t nat -I PREROUTING -i eth0.1 -p tcp --dport 80 -j DNAT --to-destination 10.0.X.Y iptables -t nat -I POSTROUTING -o eth0.2 -s 10.0.X.0/24 -j MASQUERADE Stateful firewall w/ overall drop policy on FORWARD chain, hence: iptables -I FORWARD -i eth0.1 -d 10.0.X.Y -p tcp --dport 80 -j ACCEPT Can ping from ETH_ROUTER to BRIDGED_DEVICE but unable to reach the web server from Internet. I see packet cont increasing for the DNAT rule but not sure where it disappears in the ETH_ROUTER after that. ETH_ROUTER is the only device that can be configured to achieve this. If familiar with this scenario, please suggest what I may be missing or doing wrong here or suggest techniques to debug?

  Read the article

• Ping server NETBIOS name returns wrong IP and "Destination host unreachable"

  - by music2myear

  Problem server is Windows 2008 R2 VM running on VMWare ESXi 4 host. Single network adapter manually assigned single IP address (192.168.1.11). When I ping the server from any other network computer, it returns 192.168.1.124 and "Destination host unreachable". Yesterday I found a second network adapter assigned to this server with an IP of 169.254... indicating it had no real valid IP. Using the MAC addresses I determined which adapter was not needed/not wanted, and removed it using VMWare systems. This is the network Printer Server and, understandably, nothing is printing right now. I've looked at the solutions here Why was my ping answered by a different IP address than the one pinged? and they aren't applicable to my situation for the following reasons: Output of arp -a on another computer returns the correct IP address (.1.11) assigned to the correct MAC address, the incorrect IP .1.124 is not listed, and the MAC of the network adapter I removed yesterday is not listed at all. I checked out the Microsoft KB article which listed pretty much my exact symptoms ( http://support.microsoft.com/kb/981953 ) and it says to check binding orders and look for hidden adapters. But there are no hidden adapters, and there is only one Network Adapter listed in the Binding Order list. Essentially, I can communicate from the server TO any other network device, but I cannot communicate from any other network device TO the server. Help! UPDATE: Solution found, see this solution for the details.

  Read the article

• Western Digitial My Book: Can't access the data on the drive

  - by Bryan Denny

  My girlfriend has this external hard drive by Western Digital called a My Book. When the external drive is connected, it does not show it as an accessible disk drive on the computer. However, it shows up fine in Device Manager: I can also see it in Disk Management, but the volume is not mapped to a drive letter, nor can I change the drive letter: It only gives me access to Delete Volume: I would rather not lose the data on the drive if possible. What can I do from here to get to the data? Things I've tried/know: Uninstall drivers and re-install them Device does the same thing when attach to either her Win7 laptop or my Win8 laptop I don't think there's an issue with the HDD itself. No clicking noises, etc. I ran Western Digital Data LifeGuard Diangostics (DLGDIAG) and the SMART Status was a "PASS", all of the SMART Disk Information looked fine. I haven't had the time to run the diag tests yet but I do not believe it's a mechanical issue. The hard drive is inside of an enclosure, I have not attempted to pry the drive out yet. How can I get Windows to properly detect this drive?

  Read the article

• Two parts: linux startup script to connect to bluetooth and cron to keep it connected

  - by D.R.

  I have a mini bluetooth keyboard and a Raspberry Pi running a Debian-based distro. I know the MAC address of the keyboard but for this question, let's just use AA:BB:CC:DD:EE:FF. Right now I have to have a wired keyboard connected as well as my bluetooth dongle for the mini-keyboard and on the wired keyboard, I have to run the following when the device boots up: sudo hidd --connect AA:BB:CC:DD:EE:FF If the device goes idle for too long, then the bluetooth disconnects and I have to pull out my wired keyboard and retype that same command. What I'm looking for it a way to have that command run at startup and a way to sense if it gets disconnected so that it will auto reconnect. The annoying thing is that they keyboard has to be in pairing mode (even though it has already been paired) when I run that command, otherwise it tells me the host is down. So perhaps the script needs to prevent it from disconnecting due to inactivity, otherwise I'll have to put it back in pairing mode to reconnect. So to recap: - A script to connect at startup (I can make sure to put the keyboard into pairing mode before turning it on) - A script to prevent it from disconnecting (maybe some sort of signal to send to it every 60 seconds or something?) Any help with this is greatly appreciated! StackOverflow is always the best place to find answers to weird questions! I've been searching long and hard for an answer, but finally had to resort to coming here! Thanks!

  Read the article

• Setfacl configuration issue in Linux

  - by Balualways

  I am configuring a Linux Server with ACL[Access Control Lists]. It is not allowing me to perform setfacl operation on one of the directoriy /xfiles. I am able to perform the setfacl on other directories as /tmp /op/applocal/. I am getting the error as : root@asifdl01devv # setfacl -m user:eqtrd:rw-,user:feedmgr:r--,user::---,group::r--,mask:rw-,other:--- /xfiles/change1/testfile setfacl: /xfiles/change1/testfile: Operation not supported I have defined my /etc/fstab as /dev/ROOTVG/rootlv / ext3 defaults 1 1 /dev/ROOTVG/varlv /var ext3 defaults 1 2 /dev/ROOTVG/optlv /opt ext3 defaults 1 2 /dev/ROOTVG/crashlv /var/crash ext3 defaults 1 2 /dev/ROOTVG/tmplv /tmp ext3 defaults 1 2 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 /dev/ROOTVG/swaplv swap swap defaults 0 0 /dev/APPVG/home /home ext3 defaults 1 2 /dev/APPVG/archives /archives ext3 defaults 1 2 /dev/APPVG/test /test ext3 defaults 1 2 /dev/APPVG/oracle /opt/oracle ext3 defaults 1 2 /dev/APPVG/ifeeds /xfiles ext3 defaults 1 2 I have a solaris server where the vfstab is defined as cat vfstab #device device mount FS fsck mount mount #to mount to fsck point type pass at boot options # fd - /dev/fd fd - no - /proc - /proc proc - no - /dev/vx/dsk/bootdg/swapvol - - swap - no - swap - /tmp tmpfs - yes size=1024m /dev/vx/dsk/bootdg/rootvol /dev/vx/rdsk/bootdg/rootvol / ufs 1 no logging /dev/vx/dsk/bootdg/var /dev/vx/rdsk/bootdg/var /var ufs 1 no logging /dev/vx/dsk/bootdg/home /dev/vx/rdsk/bootdg/home /home ufs 2 yes logging /dev/vx/dsk/APP/test /dev/vx/rdsk/APP/test /test vxfs 3 yes - /dev/vx/dsk/APP/archives /dev/vx/rdsk/APP/archives /archives vxfs 3 yes - /dev/vx/dsk/APP/oracle /dev/vx/rdsk/APP/oracle /opt/oracle vxfs 3 yes - /dev/vx/dsk/APP/xfiles /dev/vx/rdsk/APP/xfiles /xfiles vxfs 3 yes - I am not able to find out the issue. Any help would be appreciated.

  Read the article

• NTBackup Error: C: is not a valid drive

  - by Chris

  I'm trying to use NtBackup to back up the C: Drive on a Microsoft Windows Small Business Server 2003 machine and get the following error in the log file: Backup Status Operation: Backup Active backup destination: 4mm DDS Media name: "Media created 04/02/2011 at 21:56" Error: The device reported an error on a request to read data from media. Error reported: Invalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. Error: C: is not a valid drive, or you do not have access. The operation did not successfully complete. I'm using a brand new SATA Quantum Dat-72 drive with a brand new tape (tried a couple of tapes). I carry out the following: Open NTBackup Select Backup Tab Tick the box next to C: Ensure Destination is 4mm DDS Media is set to New Press Start Backup Choose Replace the data on the media and press Start Backup NTBackup tries to mount the media Error Message shows: The device reported an error on a request to read data from media. Error reported: INvalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. On checking the log I find the following: Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8018 Date: 04/02/2011 Time: 22:02:02 User: N/A Computer: SERVER Description: Begin Operation For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. and then; Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8019 Date: 04/02/2011 Time: 22:02:59 User: N/A Computer: SERVER Description: End Operation: The operation was successfully completed. Consult the backup report for more details. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• 2008 Sever Randomly reboots.

  - by Jeff

  I'm out of ideas here. We have a 2008 Server that keeps rebooting 2-3 times a day at completely random times with an "Unexpected Shutdown" event. There are no Dumps, no events leading to it just like it loses power then comes back online. I ran a Diagnostic of the power supply and it has had continuous power for months. In addition, the temperature of the processors are maxing out at 40 degrees Celsius. Anyone have any ideas how to figure out why this is restarting all the time? This is a DMZed Web server so it doesn't do too much process wise. Here are the specs: Host Name: ~~~ OS Name: Microsoft Windows Server 2008 R2 Standard OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Server OS Build Type: Multiprocessor Free Registered Owner: Windows User Registered Organization: Product ID: ~~~ Original Install Date: 5/27/2010, 4:25:47 PM System Boot Time: 2/14/2011, 5:35:01 PM System Manufacturer: HP System Model: ProLiant DL380 G6 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 26 Stepping 5 GenuineIntel ~1586 Mhz BIOS Version: HP P62, 8/16/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume1 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 4,086 MB Available Physical Memory: 2,775 MB Virtual Memory: Max Size: 8,170 MB Virtual Memory: Available: 6,691 MB Virtual Memory: In Use: 1,479 MB Page File Location(s): C:\pagefile.sys

  Read the article

• Reducing video mode switching during Linux boot

  - by Zack

  When I boot up my desktop computer, which only has Linux on it, the video mode and/or console font gets switched four times: When GRUB starts, it switches from 80x25 text to a graphical mode so it can draw a pretty background behind its menu; GRUB then goes back to 80x25 text after I pick something from the menu; When the KMS driver for my video card loads, it switches to a much higher-resolution text mode (I don't know if this is a hardware text mode or not); Finally X starts and it goes graphics and stays that way. I think this last switch does not change the resolution of the video mode, only the graphicalness. I'd like to get rid of as many of these mode switches as possible. Ideally, when GRUB takes over from the BIOS it would go directly to the same high-resolution text mode that the KMS driver selects, and the display would stay in that mode till X starts and brings up graphics. I am under the impression that this is possible by mucking with the kernel command line and/or the GRUB console module load parameters, but I don't know the details. GRUB 1.98+20100706, kernel 2.6.32.15 using Nouveau video drivers. Distro is Debian unstable. Please no answers that involve recompiling anything or cobbling together bleeding-edge kernel/driver combinations, I don't care enough about this to go to that much trouble. EDIT: Tobu suggests setting GRUB_GFXMODE to the full pixel resolution of the monitor, and GRUB_GFXPAYLOAD_LINUX=keep to avoid the mode switch after the menu goes away. This does part of what I want, but winds up being worse overall. There's no mode switch after the menu, but there's still a painfully-slow screen repaint (I should probably just give up on GRUB's gfxmode, it's waaaay too slow at 1920x1200). More seriously, there's now a double mode switch when nouveaufb loads, along with fun-looking error messages in dmesg [ 5.923798] [drm] nouveau 0000:02:00.0: allocated 1920x1200 fb: 0x40250000, bo ffff8801ba5f4600 [ 5.923802] fb: conflicting fb hw usage nouveaufb vs EFI VGA - removing generic driver [ 5.923821] [drm] nouveau 0000:02:00.0: PFIFO_INTR 0x00000010 - Ch 1 ("PFIFO_INTR" message repeats 400+ times) [ 5.925609] Console: switching to colour dummy device 80x25 [ 5.925802] Console: switching to colour frame buffer device 240x75

  Read the article

• How do I boot [embedded] linux from sd card?

  - by Brandon Yates

  I am hacking together a quick embedded linux system on a DM816x evm board. Previously I have been using TFTP and NFS to load my kernel and root filesystem to the board. I am now trying to switch over to loading everything from an SD card. I have my card partitioned such that uBoot and my kernel image are in one partition, and my rootFS in another partition. At power-on, Uboot starts correctly and successfully launches the kernel. However, the kernel is unable to mount the root file system. It appears that it doesn't recognize any SD (mmc) cards. It gives this error message. VFS: Cannot open root device "mmcblk0p2" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: 1f00 256 mtdblock0 (driver?) 1f01 8 mtdblock1 (driver?) 1f02 2560 mtdblock2 (driver?) 1f03 1272 mtdblock3 (driver?) 1f04 2432 mtdblock4 (driver?) 1f05 128 mtdblock5 (driver?) 1f06 4352 mtdblock6 (driver?) 1f07 204928 mtdblock7 (driver?) 1f08 50304 mtdblock8 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) I feel like I'm missing something fundamental here. Why does it not recognize the root device I am trying to load from? Here is my uBoot boot script that is running: setenv bootargs console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw mem=124M earlyprink vram=50M ti816xfb.vram=0:16M,1:16M,2:6M ip=off noinitrd;mmc init;fatload mmc 1 0x80009000 uImage;bootm 0x80009000

  Read the article

• 100% iowait + drive faults in dmesg

  - by w00t

  Hi, I have a server on which resides a fairly visited web app. It has a raid1 of 2 HDDs, 64MB Buffer, 7200 RPM. Today it started throwing out errors like: kernel: ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen kernel: ata2.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in kernel: res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout) kernel: ata2.00: status: { DRDY } kernel: ata2: hard resetting link kernel: ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) kernel: ata2.00: max_sectors limited to 256 for NCQ kernel: ata2.00: max_sectors limited to 256 for NCQ kernel: ata2.00: configured for UDMA/133 kernel: sd 1:0:0:0: timing out command, waited 7s kernel: ata2: EH complete kernel: SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) kernel: sda: Write Protect is off kernel: SCSI device sda: drive cache: write back All day long it has been in load higher than 10-15. I am monitoring it with atop and it gives some bizarre readings: DSK | sda | busy 100% | read 2 | write 208 | KiB/r 16 | KiB/w 32 | MBr/s 0.00 | MBw/s 0.65 | avq 86.17 | avio 47.6 ms | DSK | sdb | busy 1% | read 10 | write 117 | KiB/r 17 | KiB/w 5 | MBr/s 0.02 | MBw/s 0.07 | avq 4.86 | avio 1.04 ms | I frankly don't understand why only sda is taking all the hit. I do have one process that is constantly writing with 1-2megs but what the hell.. 100% iowait?

  Read the article

• Constant beeping

  - by Bogi Juul Peterson

  My computer has a problem with beeping. I'll first tell you how it started: One night I decided to watch a cartoon, and I took some water and food with me to eat while I watch. I fell asleep and when I woke up I had spilled water all over my keyboard. I didn't react quickly, because it went unnoticed for about 1 and a half hours. When I noticed, I quickly put my laptop on a radiator to try to dry it. When I turned the computer on there was a constant beeping sound. I didn't know what caused it, and I'm still not sure, but I think it has something to do with the USB hub. If I let the computer stand for some hours without any USB connections, it's fine, but when I put any kind of USB device in, it starts beeping. The laptop keyboard doesn't work so I have to have some kind of USB device connected to use the computer. The beeping is going on while I'm writing this and it makes my computer lag so much that it can make delays from the keyboard be from 1 second to 10 seconds. I need this computer because I don't have the money to buy a new one, and I have to use this computer for homework and games. The beeping is constant, with less than a second between beeps. If anyone has a solution, please help.

  Read the article

• Windows PE network setup

  - by microchasm

  I'm walking through the following step-by-step guide for deploying Windows 7 via AIK: http://technet.microsoft.com/en-us/library/dd349348%28WS.10%29.aspx On step 4 (Capturing the Installation onto a Network Share), I run into a bit of a snag: attempting to connect to a network drive repeatedly fails. I'm using/deploying Dell Optiplex 380 64 bit machines, and the network cards seem to be really wonky. On the machine that I'm using to run AIK etc, the network driver wasn't found automatically. I had to manually go in and install the driver (which was found on the OEM installation media). I've since copied this to the USB key that I'm using for the Autounattend.xml so its handy. I think that because of this, the PE environment doesn't or can't instantiate the network device. Is there a way to install/configure the network device through the command prompt in PE? If not, I read about adding in the answer file path(s) to drivers, but if I did it this way, would I have to start the process all over again (i.e. create new Autounattend.xml with the PnPcustomizations path included, re-run the installation on the reference machine, install all the applications, re-make the PE iso, reboot into new PE iso)? Any shortcuts, direction, or advice would be appreciated. Thanks!

  Read the article

• Authenticate VNC session with ConsolKit?

  - by lori

  I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

  Read the article

• Millions of files in php's tmp error - how to delete?

  - by Jonatan Littke

  Hey. I've got a tmp-folder with 14 million php session files in my home directory. At least that's what I think it is, it's not like I could ls it or anything. How can I empty this folder? I've tried using find with the -exec rm {} \; commands but that didn't work. ls 'sess_0*' | xargs rm did neither. I'm currently running rm -rf tmp but after two hours the folder appears to be the same size. REFERENCE INFO: I suddenly encountered an error where SESSIONS could no longer be written to disk: [Mon Apr 19 19:58:32 2010] [warn] mod_fcgid: stderr: PHP Warning: Unknown: open(/var/www/clients/client1/web1/tmp/sess_8e12742b62aa68a3f9476ec80222bbfb, O_RDWR) failed: No space left on device (28) in Unknown on line 0 [Mon Apr 19 19:58:32 2010] [warn] mod_fcgid: stderr: PHP Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct (/var/www/clients/client1/web1/tmp) in Unknown on line 0 I ran: $ df -h Filesystem Size Used Avail Use% Mounted on /dev/md0 457G 126G 308G 29% / tmpfs 1.8G 0 1.8G 0% /lib/init/rw udev 10M 664K 9.4M 7% /dev tmpfs 1.8G 0 1.8G 0% /dev/shm But as you can see, the disk isn't full. So I had a look in the syslog which says the following 20 times per second: kernel: [19570794.361241] EXT3-fs warning (device md0): ext3_dx_add_entry: Directory index full! This led me thinking to a full folder, obviously, but since my web folder only has 60k files (having counted them), I guessed it was the tmp folder (the local one, for this instance of php) that messed things up. Some commands I ran: $ sudo ls sess_a* | xargs rm -f bash: /usr/bin/sudo: Argument list too long find . -exec rm {} \; rm: cannot remove directory '.' find: cannot fork: Cannot allocate memory I'm running Debian Lenny, php5, ISPConfig, SuEXEC and Fast-CGI.

  Read the article

• Problems with synaptic touchpad

  - by penlite

  The "enhanced" features of the synaptics touchpad (ie scroll, pinch zoom) on my windows 7 64 bit dell studio 17 only work intermittently. This was an issue with the original OEM driver and also with the new driver from synaptics - please do not suggest that i update, reinstall, install as administrator, check or jiggle the driver - if i hear that one more time i will freak out. I have researched this for days and appears to be a common problem without a solution (many suggestions to update the driver though -argh). Dell and synaptics have not been helpful. I have checked that syntpehn.exe and syntphelper.exe are running (sometimes the UAC seems to block syntpehn.exe from running at startup). When the touchpad fails i can still use it to control the pointer and access the synaptics settings although some of the options are disabled (greyed out or simply unresponsive). It is the only pointing device i have installed - i had a logitech trackball attached but have uninstalled all software and drivers (including hidden devices) as per synaptic. It is also the only device using IRQ 12. Any help would be greatly appreciated except "update the driver".

  Read the article

• Dell XPS 17 Laptop USB SS Ports don't work until machine rebooted

  - by Matt

  I have a new Dell XPS 17 laptop and have an issue that the two USB SS ports on the rear of the machine are not recognising anything when I start-up. Have tried mouse, keyboard, headset, USB display. If I plug a USB hub in the power light on the hub lights (presume this is hard-wired) but a mouse plugged into the hub does not light up. If I restart the pc the ports work fine. Also the other two USB ports work fine all the time. I have switched off the power saving setting on the device manager (Power managementAllow the computer to turn off this device to save power) and also in the advanced power settings (USB Settings USB Selective suspend setting:disabled) I have also disabled USB powershare in the BIOS (not sure what this actually does!) This is becoming very annoying having to restart the machine every day before I can start work Running Win 7 Pro x64 EDIT: I have found that setting USB Emulation to Disabled has helped the devices to be recognised during start up but they keep dropping out completely when in use EDIT 2: I contacted Dell about this issue who told me to update the BIOS driver, when I asked if I should downgrade from the factory installed A13 to the A12 posted on the dell website they said no. However there is now an A14 available on the website has anyone tried this?

  Read the article

• Bluescreen Stop 0x00000027 RDR_FILE_SYSTEM after cloning system on new HDD

  - by Daniel

  A couple of months ago I got a new 500GB HDD for my no-name-brand Laptop PC and I cloned the complete Win 7 Pro 32bit system with clonezilla from the old 70GB drive to the new one. At first everything was great, the new driver was immediately updated. But since then I get on a more and more frequent level (used to be every 2-3 days, but now it's more like 2-3 times a day) a BSOD Stop error. From the eventlog in Windows I know that there are two different error codes sppoking aroung: 0x00000027 (0xbaad0073, 0x9954f80c, 0x9954f3f0, 0x8ecd7c82) RDR_FILE_SYSTEM 0x00000044 (0x85443230, 0x00000eae, 0x00000000, 0x00000000) MULTIPLE_IRP_COMPLETE_REQUESTS I checked for viruses and did a complete HDD check using the Windows tool and WesternDigital tool (which is the producer of the new HDD) without results. I also looked for driver updates but couldn't find any. The name of the HDD as shown in the device manager is: WDC WD5000BPVT-00HXZT1 ATA Device. I'm really a noob regarding those kind of problems, so if you have any idea what I can try without losing all my data, let me know. Also, if any additional information are required.

  Read the article

• Dual Monitor setup issues between laptop and external led monitor

  - by Julian

  I have two challenges. Monitor will not connect to laptop through HDMI Watching HD video content causes the laptop to sometimes turn off expecially when I'm streaming from tekzilla.com Setup. I got my new HP 2311x LED LCD monitor this week and I have it running as the main monitor extended by the 15 inch screen on my Dell Studio 1558. Right now I have to connect the external monitor through VGA. For the HDMI connection issue. I suspect that either the appropriate drivers are not installed because I don't see any hdmi device in the device manager. I've checked and I don't see any hdmi specific drivers listed online. For the shut down issue, I suspect the laptop might be overheating. Not sure why it would. It never did that while I watched movies on my laptop's default screen. My Laptop Configuration: 15" led lcd screen at 1366 x 768 intel i5 processor integrated graphics card 4 GB DDR3 RAM 500 GB hard drive I've tried everything from switching the source on my monitor to hdmi to start up combinations and nothing has worked. What could be the issue and how do I solve it?

  Read the article

• Using public interfaces on a server connected through a GRE tunnel

  - by Evan

  I'm pretty new to networking so please forgive any terminology mistakes. I have 2 servers connected with a GRE tunnel. Server1 (10.0.0.1) ---- Server2 (10.0.0.2) I want to be able to bind to the public IPs on Server2 using Server1. To do this, I setup virtual interfaces with Server2's public IPs on Server1 and then used routing rules on Server1 to route the packets through the GRE tunnel. On Server1: ip rule add from [Server2's first public IP] table gre ip rule add from [Server2's second public IP] table gre ip route add default via 10.0.0.2 dev gre1 table gre This works great and I can see the packets arriving via GRE on Server2. I can see the packet exiting the tunnel on Server2's gre1 device as shown: From Server1: ping -I [Server2's public ip] google.com tcpdump from Server2's GRE tunnel device: 12:07:17.029160 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) [Server2's public ip] > 74.125.225.38: ICMP echo request, id 6378, seq 50, length 64 This is exactly the packet I want. However, I'm not seeing it go out at all on eth0:0 (where Server2's public IP is bound to). I've tried to use routing rules to get packets coming from Server2's public IP (which would be coming out of dev gre1) to go through dev eth0 on the public default gateway and that doesn't work either. I'm at a loss, thank you to anyone who can help.

  Read the article

• Cannot find wireless driver for HP laptop

  - by rodey

  I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

  Read the article

• RAID administration in Debian Lenny

  - by Siim K

  I've got an old box that I don't want to scrap yet because it's got a nice working 5-disk RAID assembly. I want to create 2 arrays: RAID 1 with 2 disks and RAID 5 with the other 3 disks. The RAID card is Intel SRCU31L. I can create the RAID 1 volume in the console that you access with Ctrl+C at startup. But it only allows for creation of one volume so I can't do anything with the 3 remaining disks. I installed Debian Lenny on the RAID 1 volume and it worked out nicely. What utilites could I now use to create/manage the RAID volumes in Debian Linux? I installed the raidutils package but get an error when trying to fetch a list: #raidutil -L controller or #raidutil -L physical # raidutil -L controller osdOpenEngine : 11/08/110-18:16:08 Fatal error, no active controller device files found. Engine connect failed: Open What could I try to get this thing working? Can you suggest any other tools? Command #lspci -vv gives me this about the controller: 00:06.1 I2O: Intel Corporation Integrated RAID (rev 02) (prog-if 01) Subsystem: Intel Corporation Device 0001 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Step ping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 26 Region 0: Memory at f9800000 (32-bit, prefetchable) [size=8M] [virtual] Expansion ROM at 30020000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: PCI_I2O Kernel modules: i2o_core

  Read the article

< Previous Page | 286 287 288 289 290 291 292 293 294 295 296 297  | Next Page >