Search Results

Search found 10693 results on 428 pages for 'max requests'.

Page 322/428 | < Previous Page | 318 319 320 321 322 323 324 325 326 327 328 329  | Next Page >

• Why can't I renew my dynamic IP address?

  - by qwerty

  So, I'm going to explain this from the start. I've started a project with a friend of mine which includes a webspider, that crawls through all pages on a site and stores them in a DB. Since I've never done this before, I didn't think about the amount of requests I was actually sending to the site, and after a day or two I finally got my IP blocked. I need to be able to visit that site as it's very important to me. Not only for my project, but for other reasons too. (and if I'm able to renew my IP I'm going to set a delay on the crawler so I don't get blocked & DDOS the site) I have a dynamic IP address, at least that's what my router settings say. I've tried ipconfig /flushdns, ipconfig /release, restart computer. No result. I end up with the same IP address. I've also tried renewing it from the router, however, I think it uses the same method which isn't working. Is it possible that site has blocked my mac address? Can a site even access my mac address?

  Read the article

• IIS login / logout interferes with media player

  - by Mark Sowul

  So I'm listening to music with Windows Media Player, going insane because the music randomly stops playback every so often. I finally notice that it correlates with instances of csrss, winlogon, and logonui repeatedly starting and quitting. I finally tracked that down to IIS repeatedly logging on and off due to WebDAV requests going through my user account (my laptop syncing up with OneNote over WebDAV). I see tons of spam in my security event log for the logins. I am surprised that IIS needs to log in this much. This has only been happening for a couple of months. I'm not sure where the actual problem lies - with IIS, or Media Player, or what, so I figured I'd try and find out if the IIS login behavior is actually abnormal. Is it normal for IIS to log in this much? And is it normal for that to keep spawning winlogon, csrss, and logonui every second or so? I see a constant stream of logon events in the event log every few seconds presumably while OneNote is syncing. Logon (id = 1, source = laptop), Special Logon (id = 1, sets up privileges), Special Logon (id = 1, seems to set up the same privileges), Logon (id = 2, same laptop), Logoff (id = 2), Logoff (id = 1) The DefaultAppPool (only one apparently in use) has its idle timeout set to 20 minutes, and load user profile set to false. Not sure what other settings (if any) might be relevant.

  Read the article

• pfSense Load Balancer and Virtual IP

  - by jshin47

  I have two identical web servers on 10.2.1.13 and 10.2.1.113. I would like to set up pfSense load balancer to balance requests to both of these. I set up pools that included HTTP and HTTPS for both of these hosts, then set up virtual servers that responded on HTTP and HTTPS and referred traffic to its respective pool. However, I set up the virtual server to listen on 10.2.1.213, a LAN IP rather than a WAN IP, because I want LAN traffic to be able use the load balancer virtual server as well. So, I set up a Virtual IP for 10.2.1.213 on LAN IP, and a NAT port forwarding rule for HTTP and HTTPS traffic on a WAN IP to forward to 10.2.1.213. It seems like this should work, but it fails. What eventually happens is that when I try to access the page from WAN, I am directed to the login page for my pfSense device rather than the page I am expecting. When I try to access 10.2.1.213 from LAN, the request times out. What is going wrong here? I have tried it with and without NAT reflection to no avail. Please advise

  Read the article

• Is .htaccess slowing down my dedicated server?

  - by David Robles

  First of all, I consider myself more a programmer than a servers guy. I have a website where I receive about 3,000 visits per day, which I think is a lot less than the max capacity for a dedicated server. However, I've noticed that the connection to the website is pretty slow, e.g., to load images, to connect to it via SSH, etc. I configured .httaccess recently to avoid hotlinking to images in my server (i.e. .jpg, .gif and .png), and I was wondering if that could be slowing down my website. This is the configuration that I have: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteEngine on RewriteCond %{HTTP_REFERER} !^$ RewriteCond %{HTTP_REFERER} !^http://www.mysite.com/.*$ [NC] RewriteCond %{HTTP_REFERER} !^http://www.mysite.com$ [NC] RewriteRule .*\.(jpg|jpeg|gif|png|bmp|swf)$ http://www.google.com/ [R,NC] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> # END WordPress I found some code to do that in google, and I just copied to .htacces since I'm not an expert in apache. It works, but I don't know if that is the best way to do it. How can I see if that is the reason why the server is slow? Are there any tools to monitor it? What would you do guys? Thanks in advance!

  Read the article

• Squid3 not caching simple request and response

  - by Nick Spacek

  Hi folks, I've pared down my squid.conf to try to figure this out: http_port 80 accel defaultsite=host.to.cache cache_peer ip.to.cache parent 80 0 no-query originserver acl our_sites dstdomain host.to.cache http_access allow our_sites refresh_pattern . 1 20% 4320 Requests are being proxied correctly, so that's a start. Here's a request: GET http://host.to.cache/path?some_param=true Accept: */* Accept-Charset: ISO-8859-1,utf-8 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-US,en Connection: keep-alive Host: host.to.cache User-Agent: myuseragent And the response: Connection: keep-alive Content-Length: 585 Content-Type: application/xml Date: Thu, 06 Jan 2011 18:33:11 GMT Via: 1.0 localhost (squid/3.0.STABLE19) X-Cache: MISS from localhost X-Cache-Lookup: MISS from localhost:80 The response has no caching-related headers, but I thought that refresh_pattern would set a default behavior for responses without caching-related headers. For my test, I wanted to cache everything for one minute at minimum. Am I missing something obvious? I did take a peek at this question: Squid isn't caching ...and ran through the page here: http://www.mnot.net/cache_docs/ briefly, but didn't see anything relevant (not to say that there isn't, I could have missed something). Thanks for any help.

  Read the article

• ssl port didnt work on nginx

  - by Jin Lin

  I set up the unicorn and nginx on one of my ec2 machine. and my request are loading ok with nginx listen to port 80. but when I enable it to ssl, which listen to port 443. It doesn't work. and it can still work with port 80, https. server { listen 443 ssl; # replace with your domain name server_name domain.com; # replace this with your static Sinatra app files, root + public root /home/ubuntu/domain/public; ssl on; ssl_certificate /etc/ssl/domain.crt; ssl_certificate_key /etc/ssl/domain.key; # maximum accepted body size of client request client_max_body_size 4G; # the server will close connections after this time keepalive_timeout 5; location ~ ^/assets/ { add_header ETag ""; gzip_static on; expires max; add_header Cache-Control public; } location / { proxy_set_header X-Forwarded-Proto https; try_files $uri @app; } location @app { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; # pass to the upstream unicorn server mentioned above proxy_pass http://unicorn_server; } }

  Read the article

• Nginx configuration question

  - by Pockata

  Hey guys, i'm trying to make the autoindex feature only run for my ip address with this code: server{ ... autoindex off; ... if ($remote_addr ~ ..*.*) { autoindex on; } ... } But it doesn't work. It gives my a 403 :/ Can someone help me :) Btw, i'm using Debian Lenny and Nginx 0.6 :) EDIT: Here's my full configuration: server { listen 80; server_name site.com; server_name_in_redirect off; client_max_body_size 4M; server_tokens off; # log_subrequest on; autoindex off; # expires max; error_page 500 502 503 504 /var/www/nginx-default/50x.html; # error_page 404 /404.html; set $myhome /bla/bla; set $myroot $myhome/public; set $mysubd $myhome/subdomains; log_format new_log '$remote_addr - $remote_user [$time_local] $request ' '"$status" "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; # Star nginx :@ access_log /bla/bla/logs/access.log new_log; error_log /bla/bla/logs/error.log; if ($remote_addr ~ 94.156.58.138) { autoindex on; } # Subdomains if ($host ~* (.*)\.site\.org$) { set $myroot $mysubd/$1; } # Static files # location ~* \.(jpg|jpeg|gif|css|png|js|ico)$ { # access_log off; # expires 30d; # } location / { root $myroot; index index.php index.html index.htm; } # PHP location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $myroot$fastcgi_script_name; include fastcgi_params; } # .Htaccess location ~ /\.ht { deny all; } } I forgot to mention that when i add the code to remove static files from my access log, the static files cannot be accessed. I don't know if it's relevant :)

  Read the article

• Is it a good idea to run Redmine using Webrick through Nginx?

  - by Rohit

  The task here is to get Redmine setup for a small (<20) team. There may be a few users who would access the setup as business clients. I am familiar with setting up PHP for Apache, and recently, Nginx. I am not familiar with Ruby, Ruby-On-Rails, etc. I prefer to use the OS's (Ubuntu Linux LTS) package manager to install the different components as it takes care of dependencies and updates. I have setup Nginx with PHP-FPM successfully and am struggling with Redmine. As suggested here, I got Redmine running on port 3000. # /etc/init/redmine.conf # Redmine description "Redmine" start on runlevel [2345] stop on runlevel [!2345] expect daemon exec ruby /usr/share/redmine/script/server webrick -e production -b 0.0.0.0 -d And using the Nginx config on this page, I used Nginx to proxy requests to Webrick. server { listen 80; server_name myredmine.example.com; location / { proxy_pass http://127.0.0.1:3000; } } This works well locally. I wanted some opinions before trying this out on the live box (a 256 MB VPS). Further, should I use something like monit to monitor webrick for failure?

  Read the article

• FTP FileWatcher

  - by Meiscooldude

  So, I am in this little predicament where I am stuck watching a few ftp folders to see if they have new files added to them. If they do, it needs to throw an event with the file name. Thereby telling something else to download that file. This is a pretty simple object to make, I was just curious if anyone knew how expensive this operation would be? I plan on using the command NLIST because I don't need file size information, and there will be no sub-directories in the folder. Each file in the folder will have exactly 25 characters in its name. There could be anywhere from 10 to 'maybe' a couple thousand (max around 2000) files per folder (usually on the lower end, 100-300, but currently growing). The files are anywhere from 250kb to a very VERY unlikely 10mb (usually within the 250kb to 4mb range). There possibly could be up to a few hundred folders (in which case I could change the watch frequency depending on number of folders), but currently there are only a few (6-10ish). There also would be multiple logins for the ftp server, different logins would have access to different folders. I am not asking for an implementation, just if anyone has some first or second hand knowledge about FTP, how could this affect my network. I am not opposed to putting in file retention times or change the frequency in which I check for new files.

  Read the article

• Why is lighttpd and fastcgi keeping sending me the *.scgi file instead of the website content?

  - by e-satis

  I have the following config: server.modules = ( "mod_compress", "mod_access", "mod_alias", "mod_rewrite", "mod_redirect", "mod_secdownload", "mod_h264_streaming", "mod_flv_streaming", "mod_accesslog", "mod_auth", "mod_status", "mod_expire", "mod_fastcgi" ) [...] fastcgi.server = ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/var/tmp/lighttpd/php-fastcgi.socket" + var.PID, "max-procs" => 1, "kill-signal" => 9, "idle-timeout" => 10, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "200", "PHP_FCGI_MAX_REQUESTS" => "1000" ), "/pyapps/essai/blondes.fcgi" => ( "main" => ( "socket" => "/var/tmp/lighttpd/django-fastcgi.socket", ), ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" ))) [...] $HTTP["host"] =~ "(^|www\.)cam\.com(\:[0-9]*)?$" { server.document-root = "/home/cam/web/" accesslog.filename = "/home/cam/log/access.log" server.errorlog = "/home/cam/log/error.log" server.follow-symlink = "enable" # files to check for if .../ is requested server.indexfiles = ( "index.php", "index.html", "index.htm", "index.rb") url.rewrite = ( "^(/blondes/.*)$" => "/pyapps/essai/blondes.fcgi$1" ) } I have the following dir tree: /home/tv/web/ `-- pyapps `-- essai `-- __init__.py `-- blondes.fcgi `-- blondes.pid `-- django-fcgi.py `-- manage.py `-- manage.pyo `-- plop `-- settings.py `-- urls.py No error when restarting lighthttpd. The I run: ./manage.py runfcgi method=prefork socket=/var/tmp/lighttpd/django-fastcgi.socket daemonize=false pidfile=blondes.pid No errors neither. I then go to http://cam.com/blondes/. I offers me to download an empty file. I checked permissions but everything is set to the same user and group, and they work for the PHP site. The file /var/tmp/lighttpd/django-fastcgi.socket exists. When I reload the page, I got no output in error logs, nor in the manage.py runfcgi command. I probably missed something obvious, but what ?

  Read the article

• What is the best way to create a failover cluster for my IIS website?

  - by ObligatoryMoniker

  Our eCommerce website www.tervis.com currently runs on two servers: SQL server: 2005 x 86 on Windows Server 2003 Standard x86 with a single dual core processor and 4 gb of memeory IIS server: Windows Server 2008 Web edition x64 with dual quad core hyper threaded processors and 32 gb of memory Tervis.com's revenue has steadily grown to the point where we need to have redundant servers deployed with a fail over mechanism so that we do not have any down time. Because the SQL server is so underpowered compared to the web server my thought was to purchase: 2 x SQL Server 2008 R2 web edition x64 single processor license 2 x Windows Server 2008 R2 Web Edition Licenses 1 x New Physical dual quad core 32 GB server 1 x F5 Load Balancer I need the Windows Server 2008 R2 Web Edition licenses so that I can run SQL and IIS on the same box for both of these servers. The thought is to run this as an active/passive fail over cluster that could be upgraded to an active/active cluster if we purchased the additional SQL licensing. The F5 load balancer would serve as the device that monitors the two servers and if the current active one stops responding then fails over to using the other server. To be clear this is not windows clustering but simply using a load balancer to fail over between two computers so that you now have a cluster in the general sense. Is this really the best way to accomplish what I need? Is there some way to leverage the old server 2003 SQL server to function as the devices that funnels http requests to the appropriate active server and then fails over if a problem occurs? Is there any third party clustering software that might help me accomplish this in a simpler fashion?

  Read the article

• Splitting build cross the network?

  - by Dandikas

  Is there a known solution for splitting build process cross the network machines? Use case: We are an average software development company. We own around 50 development workstations (Quad Core 2.66Ghz, 4 GB ram, 200 GB raid). No need to tell that at any single moment not every machine is loaded to the max. There are 5 to 15 projects running simultaneously at any single moment. Obviously all of them are continuously build on server, than deployed to proper environment. Single project build is taking from 3 to 15 minutes. The problem: Whenever we build 5 projects in a row the last project is going to be ready after around 25 - 50 minutes. Building in parallel does not solve the problem (build is only a part of the game, than you need to deploy, run tests etc.) YES the correct solution is to add another build server, but "That involves buying new Expensive hardware, and we already spent a lot!". Yea, right(damn them)! Anyway. What about splitting build among developers workstation? Lets say whenever we need to build project "A" we check 5 workstations and start build on all that are not overloaded. The build can be canceled by a developer if he really needs all the power of his machine as long as there is at least 1 machine that is still building. After build is finished deployment can be performed to a proper environment (hosted on some server, not on workstation :) ). The bigger the company the more this makes sense to me. Anyone tried something like this? Are there any good practices? Any helpful software?

  Read the article

• Unable to PPTP through NAT on Cisco 881

  - by MasterRoot24

  I'm trying to connect to a PPTP server which is sat behind a Cisco 881 NAT router. The server is running Ubuntu Server 12.04 and is running Poptop pptpd as the PPTP daemon listening for connections. As discussed in my other question, I'm trying to setup a Cisco 881 router to replace my old Linksys WAG320N. This same server and WAN connection worked fine with the WAG320N with no special configuration, other than allowing 1723 in through the firewall. On the Cisco 881, I'm using the newer ip nat enable or NAT NVI to setup static routes in through the firewall for the services running behind the router. My reason being that I can't run another copy of my live DNS domains internally with local IP addresses in. For the purposes of this question, though, I have rebuilt the router with ip nat inside/outside style NAT'ing, but this issue is still apparent. HTTP/SMTP/IMAP etc. all work ok from both the WAN and LAN interfaces of the router. I'm only having issues with SIP (see other question) and PPTP. My issue is that the GRE doesn't appear to be passing through NAT correctly and one end of the connection is not receiving GRE traffic when it should be, so the server hangs up the connection. Here's an example of /var/log/syslog with debug enabled in /etc/pptpd.conf: Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: MGR: Launching /usr/sbin/pptpctrl to handle client Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: local address = 192.168.1.50 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: remote address = 192.168.1.51 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: pppd options file = /etc/ppp/pptpd-options Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Client 82.132.248.216 control connection started Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 1) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Made a START CTRL CONN RPLY packet Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: I wrote 156 bytes to the client. Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Sent packet to client Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 7) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Set parameters to 100000000 maxbps, 64 window size Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Made a OUT CALL RPLY packet Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Starting call (launching pppd, opening GRE) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: pty_fd = 6 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: tty_fd = 7 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: I wrote 32 bytes to the client. Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Sent packet to client Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): program binary = /usr/sbin/pppd Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): local address = 192.168.1.50 Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): remote address = 192.168.1.51 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Dec 11 21:06:30 <HOSTNAME> pppd[22627]: pppd 2.4.5 started by root, uid 0 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Using interface ppp0 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Connect: ppp0 <--> /dev/pts/3 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: GRE: Bad checksum from pppd. Dec 11 21:06:31 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 15) Dec 11 21:06:31 <HOSTNAME> pptpd[22626]: CTRL: Got a SET LINK INFO packet with standard ACCMs Dec 11 21:07:00 <HOSTNAME> pppd[22627]: LCP: timeout sending Config-Requests Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Connection terminated. Dec 11 21:07:00 <HOSTNAME> avahi-daemon[1042]: Withdrawing workstation service for ppp0. Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Modem hangup Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Exit. Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: GRE: read(fd=6,buffer=6075a0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Reaping child PPP[22627] Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Client 82.132.248.216 control connection finished Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Exiting now Dec 11 21:07:00 <HOSTNAME> pptpd[5803]: MGR: Reaped child 22626 As far as Cisco are concerned, all I need is ip nat source static tcp <SERVER LAN IP> 1723 interface FastEthernet4 1723 but of course this doesn't seem to the be helping the GRE traffic through as it should. Trying the connection to the LAN IP of the server from the same LAN as the server (behind the router), the PPTP connection works fine, so I'm confident that the server's config is ok. Furthermore, all I needed on my WAG320N was to open 1723 in the firewall. Here's my current router config: ! ! Last configuration change at 20:20:15 UTC Tue Dec 11 2012 by xxx version 15.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname xxx ! boot-start-marker boot-end-marker ! ! enable secret 4 xxxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 xxx quit ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! ip domain list dmz.xxx.local ip domain list xxx.local ip domain name dmz.xxx.local ip name-server 192.168.1.x ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn xxx ! ! username admin privilege 15 secret 4 xxx username joe secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.x 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.x 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ! ! ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ! ! access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.1.0 0.0.0.255 ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 exec-timeout 15 0 login authentication local_auth line aux 0 exec-timeout 15 0 login authentication local_auth line vty 0 4 access-class 2 in login authentication local_auth length 0 transport input all ! ! end UPDATE 16/12/2012: The only progress that I have been able to make on this issue is that I'm confident that the issue is caused by the GRE tunnels (which are required for the PPTP connection to complete) are being blocked. When attempting a connection, I can see in show ip nat nvi translations that both a TCP translation on 1723 is setup and also a GRE translation is setup also. I appear to be able to see GRE related packets on the LAN that the server is on, so I am lead to believe that the server is sending(?) GRE packets, however running Wireshark on a client PC when attempting a connection shows absolutely no GRE packets. Whilst there are no configuration directives in my config posted above (that I can pin point) which would specifically block them, it would appear that the GRE packets are not being allowed in/out of the router's firewall, even though a NAT translation entry is setup to the server's LAN address. Would anyone be able to provide me with some help to ensure that GRE packets are not blocked by the router's firewall, so that this can be ruled out as a possible issue please?

  Read the article

• IIS 7.0 - responses throttled to 500ms blocks?

  - by Julia Hayward

  Scenario: ASP.NET MVC wep app sitting on my local machine (Vista Ultimate, IIS 7.0), nothing going on except one user (me) logged in and viewing an index page. The page includes 9 dynamic images drawn from the underlying DB and returned from a controller action. I have got the actual processing time for these images down to 15ms each. Turn on Firebug and watch the page load. What I see is 9 requests for images firing off together – no surprise – but four come back to me almost immediately; two more after 0.5s; another after 1s; then at 1.5s and 2s. Logging on the server side suggests the individual responses are still only taking 15ms. So it appears IIS is queueing things up into 500ms chunks. (Repeating the experiment produces different results, but each time the images return in similar blocks – you might get three in the first group, then three at 0.5s, two at 1s etc, for example – and it’s always at 500ms intervals, not anything else.) It’s also repeatable cross-browser, and it’s not repeatable with other forms of content. I haven't found any particular mention of this problem out there, so I'm sort of assuming it's not an IIS bug, so is it: i) IIS on desktop OSs deliberately does it, to make you use server OSs in production? ii) There is some magical setting that has eluded me for as long as I’ve known IIS? iii) Something peculiar to MVC or SQL Server 2008? or something else?

  Read the article

• Does MySQL log successful or attempted queries?

  - by Nathan Long

  I'm trying to track down a hit-or-miss bug in a web application. Sometimes a request completes just fine; sometimes it hangs and never finishes. I see that Apache now has several requests listed on the server-status page as "sending reply," and that doesn't change. I'm testing on localhost, so there shouldn't ever be more than one. Out of curiosity, I set MySQL to log all queries and I'm tail -fing the log file. When things go OK, I see a pattern like this: 20 Connect root@localhost on dbname 20 Query (some query #1) 20 Query (some query #2) (etc) 20 Quit 21 Connect (etc) When it hangs, I see a pattern like this: 22 Connect root@localhost on dbname 22 Query (some query #1) //nothing happens, so I try the post again 23 Connect root@localhost on dbname 23 Query (some query #1) //nothing happens; try again 24 Connect (etc) Here's my question: is MySQL logging attempted queries, or successful queries? In other words, if the last line I see is query #1, does that imply that query #1 or query #2 is hanging? My guess is that the one I don't see is the problem, because the last one I see looks fine, but maybe the one I don't see is too screwed-up for MySQL to process. Thoughts?

  Read the article

• Website has become slower on a VPS, was much fast on a shared host. What's wrong?

  - by Arpit Tambi

  My shared host suspended my website stating system overload, so I moved my website to a VPS which has 4GB RAM. But for some reason the website has become very slow. This is the vmstat output - procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 1 0 0 3050500 0 0 0 0 0 1 0 0 0 0 100 0 0 Here's the Apache Benchmark output for a STATIC html page I ran on the server itself - Benchmarking www.ask-oracle.com (be patient)...apr_poll: The timeout specified has expired (70007) Total of 20 requests completed Update: Server Config: List item Centos 5.6 4 cores cpu 4 GB RAM LAMP stack with APC Wordpress Only one website It takes almost double time to load now, same website was much fast on shared hosting. I know I need to tweak some settings but have no clue where to start from? I have already tried to optimize apache, mysql etc. Update 2: CPU usage is low, see uptime output: 11:09:02 up 7 days, 21:26, 1 user, load average: 0.09, 0.11, 0.09 Update 3: When I load any webpage, browser shows "Waiting" for a long time and then page loads quickly. So I suspect server can accept only limited connections and holds extra connections in a waiting state. How to check this? Update 4: Following is the output on executing netperf TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to localhost.localdomain (127.0.0.1) port 0 AF_INET Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 16384 16384 10.00 9615.40 [root@ip-118-139-177-244 j3ngn5ri6r01t3]# Here are the Apache MPM settings from httpd.conf, do they look okay? <IfModule worker.c> StartServers 5 MaxClients 100 MinSpareThreads 50 MaxSpareThreads 250 ThreadsPerChild 125 MaxRequestsPerChild 10000 ServerLimit 100 </IfModule>

  Read the article

• Bypassing SQUID on freebsd with PF

  - by epema

  I have PF+SQUID31 on FREEBSD-9.0, and I want to have some hosts(aka goodguys) to bypass the proxy, so that torrents are not logged. Also, I am not sure about transparent. It means that I dont have to configure proxy settings on the client side right? I have tried doing a redirect no rdr on $int_if inet proto {tcp,udp} from 192.168.1.233/32 to any However, no luck :( Here is a quick look of my conf files: SQUID /usr/local/etc/squid/squid.conf http_port 192.168.1.1:8080 transparent RC /etc/rc.conf: gateway_enable="YES" pf_enable="YES" pf_rules="/usr/local/etc/pf.conf" pflog_enable="YES" squid_enable="YES" I have squid31 installed from ports with SQUID_PF "Enable transparent proxying with PF" on PF /usr/loca/etc/pf.conf: int_if="re0" ext_if="bge0" localnet="{ 192.168.1.0/24 }" table <goodguys> const { "192.168.1.219", "192.168.1.233" } set block-policy drop set skip on lo0 scrub in all fragment reassemble scrub out all random-id max-mss 1440 block in on $ext_if pass out on $ext_if keep state block in on $int_if pass in on $int_if inet proto tcp from $int_if:network to $int_if port 8080 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 21 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 22 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 53 keep state pass in on $int_if inet proto tcp from $int_if:network to any port { smtp, pop3 } keep state pass in on $int_if inet proto icmp from $int_if:network to $int_if keep state pass out on $int_if keep state What lines should I add in conf files? I am assuming that the problem is on the firewall(pf).

  Read the article

• What does Apache's "Require all granted" really do?

  - by John Crawford

  I've just update my Apache server to Apache/2.4.6 which is running under Ubuntu 13.04. I used to have a vhost file that had the following: <Directory "/home/john/development/foobar/web"> AllowOverride All </Directory> But when I ran that I got a "Forbidden. You don't have permission to access /" After doing a little bit of googling I found out that to get my site working again I needed to add the following line "Require all granted" so that my vhost looked like this: <Directory "/home/john/development/foobar/web"> AllowOverride All Require all granted </Directory> I want to know if this is "safe" and does not bring in any security issues. I read on Apache's page that this "mimics the functionality the was previously provided by the 'Allow from all' and 'Deny from all' directives. This provider can take one of two arguments which are 'granted' or 'denied'. The following examples will grant or deny access to all requests." But it didn't say if this was a security issue of some sort or why we now have to do it when in the past you did not have to.

  Read the article

• AD domain on web servers behind NAT - DNS issues?

  - by Ant

  I'm trying to setup an AD domain to manage the security between two Windows Server 2008 webservers that will sooner or later use NLB to balance website requests. I've hit a problem which I think is a simple solution and is down to DNS. My website domain is mydomain.com. The two servers are running behind a NAT firewall on the 10.0.0.0 IP range. I've setup the AD domain to be called ad.mydomain.com (as recommended by MS and a few other answers to questions on here). The second web server however doesn't want to join the domain, and gives an error pinning the problem on DNS - "ensure that the domain name is typed correctly" even though it queries the SRV record successfully and gets the correct DC back - dc.ad.mydomain.com. Doing a dcdiag /test:dns on the DC gives the Delegation error 'DNS Server dc.mydomain.com Missing glue A record'. I have a feeling I need to add something to the public DNS so that it in some way knows about ad.mydomain.com. Can anyone suggest whether I'm on the right track in adding something to the public DNS? Or whether it's something else? Many thanks

  Read the article

• Sun Grid Engine (SGE) / limiting simultaneous array job sub-tasks

  - by wfaulk

  I am installing a Sun Grid Engine environment and I have a scheduler limit that I can't quite figure out how to implement. My users will create array jobs that have hundreds of sub-tasks. I would like to be able to limit those jobs to only running a set number of tasks at the same time, independent of other jobs. Like I might have one array job that I want to run 20 tasks at a time, and another I want to run 50 tasks at a time, and yet another that I'm fine running without limit. It seems like this ought to be doable, but I can't figure it out. There's a max_aj_instances configuration option, but that appears to apply globally to all array jobs. I can't see any way to use consumable resources, as I'd need a "complex attribute" that is per-job, and that feature doesn't seem to exist. It didn't look like resource quotas would work, but now I'm not so sure of that. It says "A resource quota set defines a maximum resource quota for a particular job request", but it's unclear if an array job's sub-tasks' resource requests will be aggregated for the purposes of the resource quota. I'm going to play with this, but hopefully someone already knows outright.

  Read the article

• Can't write to samba share

  - by Tiddo

  I try to setup a samba file server, but whatever I do I can't get write access to work (reading works fine). This is my current situation: I have a local fileserver with 3 harddisks mounted at /mnt/share/disk<nr>. 2 of these use the ext4 filesystem, the third one is ntfs. This file server runs Fedora 18 32-bit. The root folders of these harddisks are owned by superman:superman, and testparm outputs the following: [global] workgroup = WORKGROUP netbios name = FILE_SERVER server string = Samba Server Version %v interfaces = lo, eth0, 192.168.123.191/8 log file = /var/log/samba/log.%m max log size = 50 unix extensions = No load printers = No idmap config * : backend = tdb hosts allow = 192.168.123. cups options = raw wide links = Yes [share] comment = Home Directories path = /home/share/ write list = superman, @users force user = superman read only = No create mask = 0777 directory mask = 0777 inherit permissions = Yes guest ok = Yes I've tried a lot to get this to work: the disk are chmodded to 777, I've tried turning off selinux, I've added the samba_share_t label to the disks and as can be seen in the above output I tried to make the smb config as permissive as I could, but still I cannot write to the share (tried from Windows 7 and another Fedora installation). What can I try to be able to write to the shares? EDIT: The replies I got so far are mostly concerned with the smb.conf. I have however tried a lot of different setup, ready made configs, and solutions to similar problems for the smb.conf file, so I suspect that the real problem is somewhere else.

  Read the article

• cURL - Unkown SSL protocol error - OS X 10.9

  - by saq7

  I am trying to use cURL and get the following error on every https request I make. The error is always the same. HTTP requests work flawlessly. The verbose output is quite useless. Saquibs-MacBook-Pro:~ skothawala$ curl https://google.com -vv * Adding handle: conn: 0x7fe09b803a00 * Adding handle: send: 0 * Adding handle: recv: 0 * Curl_addHandleToPipeline: length: 1 * - Conn 0 (0x7fe09b803a00) send_pipe: 1, recv_pipe: 0 * About to connect() to google.com port 443 (#0) * Trying 74.125.226.129... * Connected to google.com (74.125.226.129) port 443 (#0) * Unknown SSL protocol error in connection to google.com:-9805 * Closing connection 0 curl: (35) Unknown SSL protocol error in connection to google.com:-9805 I have looked through other answers on this forum and other places on the internet, but haven't found an answer. Most people's issues involve particular servers and the configuration of SSL on these servers. Mine however is problematic anytime HTTPS is used (with any website). Can someone please suggest what I should be looking into to solve the problem? Can it be that something is not properly configured? What should I be looking for?

  Read the article

• ASP.NET Session State SQL Server 2008 R2 Freezes with High CPU Usage

  - by jtseng

  Our ASP.Net website uses SQL Server as the session state provider. We currently host the database on SQL Server 2005 since it does not play well on 2008 R2. We would like to know why, and how to fix it. hardware setup Our current session state server has SQL Server 2005 with the files hosted on a single local disk. It is one of our oldest servers since it has served us well, and we never felt the need to upgrade it. The database is about 2 GB holding 6000 sessions. (The sessions are a little big, but we need it.) We have another server with SQL Server 2008 R2 with a much faster CPU, much more RAM, and a much faster hard disk. situation One day, we have a huge surge in traffic. The transaction log growth on SQL Server freezes the server for 10's of seconds, allowing only a few requests through in minutes. So we load up the new server with ASPState with very large data and log files and point all of our applications to the new server. It chugs along fine for about 5 minutes, and then the CPU usage jumps up to 50% of the 16 cores that Standard Edition can use and freezes for 10's of seconds at a time. The files do not record any autogrowth events. The disk queue is nice and low. RAM usage is low. CPU usage on our old server has never been higher than 5%. What happened on the new server? Alternatively, I would like to hear success stories with ASP.NET session state server running on SQL Server 2008 R2 with an average write load of 30MB/sec with bursts up to 200MB/sec.

  Read the article

• SSH into remote server using Public-private keys

  - by maria

  Hi, I have recently setup ssh on two linux machines (lets call them server-a, client-b). I have generated two ssh auth files on client-b machine using ssh key gen and can see both public and private files in .ssh dir. I have named them 'example' and 'example.pub'. Then I have added example.pub to sever-a's auth file. When I try to ssh into server-a it still requests a password authentication where as I want a password less login (private key on client-b is setup without password). When I try to ssh with '-v' .. get the following output: debug1: Next authentication method: publickey debug1: Trying private key: /Users/abc/.ssh/identity debug1: Offering public key: /Users/abc/.ssh/id_rsa debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Offering public key: /Users/abc/.ssh/id_dsa debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,keyboard-interactive debug2: we did not send a packet, disable method debug1: Next authentication method: keyboard-interactive debug2: userauth_kbdint debug2: we sent a keyboard-interactive packet, wait for reply debug2: input_userauth_info_req debug2: input_userauth_info_req: num_prompts 1 Password: Please help.

  Read the article

• fedora, dhcpd fails to start

  - by soxs060389

  History: I got a tiny shiny plugserver which I want to plug to my ADSL router (or however you want to call it) on one end (eth0), and the other end (eth1) I want to run a dhcp server for my LAN. ATM I am stuck with getting LAN to work. OS is fedora 12. I configured my /etc/dhcp/dhcpd.conf like this: # # DHCP Server Configuration file. # see /usr/share/doc/dhcp*/dhcpd.conf.sample # see 'man 5 dhcpd.conf' # option domain-name "unknown.org"; option domain-name-servers 192.168.44.1; option subnet-mask 255.255.255.0; option broadcast-address 192.168.44.255; default-lease-time 86400; max-lease-time 172800; subnet 192.168.44.0 netmask 255.255.255.0 { host fedorabigbox { hardware ethernet 00:19:66:8E:61:74; fixed-address 192.168.44.21; } #host mobile #{ # hardware ethernet ***; # fixed-address 192.168.44.22; #} range 192.168.44.100 192.168.44.110; option routers 192.168.44.1; } # this is just dummy, as read many howtos, some suggesting to add a subnet blah netmask blah for each interface subnet 192.168.33.0 netmask 255.255.255.0 { range 192.168.33.100 192.168.33.110; option routers 192.168.33.1; } But the server fails to start when trying to start it via /etc/init.d/dhcpd start In general it would be nice if someone can point me to a in detail explanation of how network works, I am pretty new to this stuff. More concrete question: How to point the subnets to eth1 and the other to eth0, how can this be achieved? Does someone see any errors or flaws? Syntax should be correct, allready checked that with the dhcpd syntax check. Thanks for any help

  Read the article

< Previous Page | 318 319 320 321 322 323 324 325 326 327 328 329  | Next Page >