Search Results

Search found 26947 results on 1078 pages for 'util linux'.

Page 324/1078 | < Previous Page | 320 321 322 323 324 325 326 327 328 329 330 331  | Next Page >

• iftop Shows Lots of Mysterious Connections - Not Showing in netstat

  - by HOLOGRAPHICpizza

  I've just stopped all pretty much all services except sshd on my server (Ubuntu Server 10.04), and when I run iftop I get output that looks like this: 12.5Kb 25.0Kb 37.5Kb 50.0Kb 62.5Kb mqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqq flash.gateway.2wire.net:ssh <=> 172.16.1.151:60405 1.75Kb 1.54Kb 2.22Kb flash.gateway.2wire.net:21095 <=> 69.127.29.20:32582 536b 107b 27b flash.gateway.2wire.net:21095 <=> 190.164.122.134:13557 0b 105b 26b flash.gateway.2wire.net:21095 <=> 79.165.212.195:45138 0b 105b 26b flash.gateway.2wire.net:21095 <=> 151.42.15.151:9031 0b 72b 18b flash.gateway.2wire.net:21095 <=> 88.185.120.179:51413 0b 0b 49b flash.gateway.2wire.net:21095 <=> 178.120.152.97:25924 0b 0b 29b flash.gateway.2wire.net:21095 <=> 109.110.217.77:27868 0b 0b 26b flash.gateway.2wire.net:21095 <=> 84.13.201.90:16509 0b 0b 26b flash.gateway.2wire.net:21095 <=> 171.7.125.224:11777 0b 0b 26b flash.gateway.2wire.net:21095 <=> 115.177.164.170:21360 0b 0b 26b flash.gateway.2wire.net:21095 <=> 50.88.126.18:25540 0b 0b 25b flash.gateway.2wire.net:21095 <=> 223.206.230.163:13431 0b 0b 25b flash.gateway.2wire.net:21095 <=> 78.144.187.26:24515 0b 0b 25b flash.gateway.2wire.net:21095 <=> 83.20.61.211:27572 0b 0b 25b flash.gateway.2wire.net:21095 <=> 82.134.151.42:18448 0b 0b 18b flash.gateway.2wire.net:21095 <=> 126.117.95.247:25316 0b 0b 18b flash.gateway.2wire.net:21095 <=> 116.202.65.230:9044 0b 0b 18b flash.gateway.2wire.net:21095 <=> 88.120.63.205:51413 0b 0b 17b qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cumm: 61.6KB peak: 8.00Kb rates: 1.59Kb 1.38Kb 2.04Kb RX: 18.4KB 1.64Kb 696b 549b 640b TOTAL: 80.0KB 9.64Kb 2.27Kb 1.92Kb 2.66Kb This is the first part (not the unix socket part) of the output of netstat -a: Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 *:ssh *:* LISTEN tcp 0 0 *:55677 *:* LISTEN tcp 0 0 flash.gateway.2wire:ssh 172.16.1.151:60405 ESTABLISHED tcp 0 48 flash.gateway.2wire:ssh 172.16.1.151:60661 ESTABLISHED tcp6 0 0 [::]:ssh [::]:* LISTEN udp 0 0 *:37790 *:* What could all those strange connections on port 21095 be? And why would they not show up in netstat?? Any advice would be greatly appreciated.

  Read the article

• using python Paramiko for ssh: sudo: no tty present and no askpass program specified

  - by misteryes

  I want to use paramiko to ssh into a bunch a remote nodes and run some command line with root priviledge I have ssh key in my home directory and so i don't need to input password when I ssh into those remote nodes but when running the following script: def connect(hostname): ssh = paramiko.SSHClient() ssh.set_missing_host_key_policy(paramiko.AutoAddPolicy()) ssh.connect(hostname, username='niky', pkey=paramiko.RSAKey.from_private_key(open('id_rsa'), 'passwd'), timeout = 240.0) return ssh def run(hostname): ssh = connect(hostname) (stdin, stdout, stderr) = ssh.exec_command("sudo ls") res = stderr.readlines() print hostname+': '+''.join(str(elem) for elem in res)+'\n' run(remote.nity.com) I got the following error: remote.nity.com: sudo: no tty present and no askpass program specified if I don't add sudo before ls everything works fine what are potential reasons ? thanks!

  Read the article

• use ubuntu server 10.4 as a virtulization server as esx from VMWare

  - by hitham

  i was wondering if its possible to use Ubuntu server as virtualization center as esxi vmware i am asking this coz i read this in ubuntu website: " Ubuntu includes a Virtual Machine Builder which makes this process simple and replicable allowing multiple pre-configured machines to be deployed instantly ". if its possible how can i do such thing ?. with all respect . Hitham Melhem

  Read the article

• droid cam makefile understanding and error

  - by nerorevenge

  I tried installing the droid cam on my fedora 19 (64 bit) . Link to the droid cam application is here and whenever I try to install it , the Makefile which is as follows is invoked obj-m := v4l2loopback-dc.o all: make -C /lib/modules/`uname -r`/build M=`pwd` test: gcc test.c -o test clean: make -C /lib/modules/`uname -r`/build M=`pwd` clean insmod: sudo insmod v4l2loopback-dc.ko width=320 height=240 rmmod: sudo rmmod v4l2loopback-dc.ko and here is the error -- INSTALL: Webcam parameters: '320' and '240' -- INSTALL: Building v4l2loopback-dc.ko make -C /lib/modules/`uname -r`/build M=`pwd` make: *** /lib/modules/3.9.5-301.fc19.x86_64/build: No such file or directory. Stop. make: *** [all] Error 2 -- INSTALL: v4l2loopback-dc.ko not built.. Failure build happens to be a symbolic link.I was wondering what exactly is the makefile trying to and why is it failing?

  Read the article

• Find all duplicate files by md5 hash

  - by Jamie Curran

  I'm trying to find all duplicate files based upon md5 hash and ordered by file size. So far I have this: find . -type f -print0 | xargs -0 -I "{}" sh -c 'md5sum "{}" | cut -f1 -d " " | tr "\n" " "; du -h "{}"' | sort -h -k2 -r | uniq -w32 --all-repeated=separate The output of this is: 1832348bb0c3b0b8a637a3eaf13d9f22 4.0K ./picture.sh 1832348bb0c3b0b8a637a3eaf13d9f22 4.0K ./picture2.sh 1832348bb0c3b0b8a637a3eaf13d9f22 4.0K ./picture2.s d41d8cd98f00b204e9800998ecf8427e 0 ./test(1).log Is this the most efficient way?

  Read the article

• How to get rid of superuser`s password?

  - by eleonora

  My father put a new superuser password on my laptop, and now i cant access my computer without him putting the password in. I am really helpless. How can i get rid of his superuser control? Can i delete or change the superuser thing? Please help!!!!

  Read the article

• What's an easy way to install a bunch of OSS apps in my home dir on my company's aging Redhat VNC servers?

  - by subopt

  My company's IT group doesn't want to install lots of common stuff on our VNC servers, which run RHEL 4. The list of stuff i want/need includes graphviz, midnight commander, various python libs, sqlite, netbeans, antlr, jdk1.6, etc. They've hobbled rpm somehow, so i can't do rpm --relocate. And i don't want the RHEL4 compatible revs of this stuff anyway. I've probably got the room to build all this stuff in my home dir, but i don't want to take forever tracking down dependencies. Looking for an easy way to get the apps/tools i need, and nothing (or very little) else. Any suggestions?

  Read the article

• Machine check events logged

  - by GoldenNewby

  In /var/log/messages, this error occurred: Sep 19 13:18:15 wdc kernel: [2772302.630416] Machine check events logged Shortly there after, the entire server became unresponsive. This is in the log of the Dom0 for a Xen Server (running the latest version on Debian Squeeze). Can anyone shed some light on what this error means? Should I be ordering new hardware? Edit: Also, it seems to imply it logged something, where can I find that?

  Read the article

• What does "link to unknown" mean?

  - by Question Overflow

  I just upgraded my server to Fedora 17 which made a switch of my bootloader from GRUB Legacy to GRUB2. There are two symbolic links in the /etc folder that points to the files grub.conf and grub.cfg in /boot/grub and /boot/grub2 respectively. Though the targets seem correct, the link icons are displaying an X status which seems to indicate that the links are broken. Upon right-clicking the property type, it states "link to unknown". The file size of the link corresponds exactly with the file size of the target file, so, why does the links appear to be broken? The image of the link icons: As requested, the following are the outputs from the commands: $ ls -l /etc/grub.conf lrwxrwxrwx. 1 root root 22 Jul 14 2011 /etc/grub.conf -> ../boot/grub/grub.conf $ ls -l /etc/grub2.cfg lrwxrwxrwx. 1 root root 22 Dec 10 18:57 /etc/grub2.cfg -> ../boot/grub2/grub.cfg

  Read the article

• MegaCLI always returns blank output

  - by JamesHannah

  This server is a Dell R200 running Ubuntu 8.04LTS using a LSI SAS1068E raid card supplied from Dell, I suspect that there might be some kind of RAID issue with the hardware raid built into the motherboard, but I can't seem to get MegaCLi to return any useful output: root@81 $ ./MegaCli -AdpAllInfo -aALL root@81 $ ./MegaCli -PDList -aALL root@81 $ The disks work and AFAIK the raid software is installed correctly. I've seen this issue on RedHat issues also in the past. The RAID was initially setup through the BIOS on this server and appears to be functioning fine apart from this.

  Read the article

• Why wireless adatper stop to work?

  - by AndreaNobili

  today I correctly installed the driver for the TP-LINK TL-WN725N USB wireless adapter on my RaspBerry Pi (I use RaspBian that is a Debian), then I setted up the wifi using the wpa-supplicant as explained in this tutorial: http://www.maketecheasier.com/setup-wifi-on-raspberry-pi/ This worked fine untill this evening. Then suddenly it stopped to work when I try to connect in SSH and the Raspberry is on the wireless (or rather it should be, as this is not in the list of my router's DHCP connected Client) The strange thing is that the USB wirless adapter blink so I think that this is not a driver problem. If I try to connect it by the ethernet I have no problem. It appear in my router's DHCP connected Client and I can connect to it by SSH. When I connect to it using ethernet if I perform an ifconfig command I obtain: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.9 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:48 errors:0 dropped:0 overruns:0 frame:0 TX packets:59 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6006 (5.8 KiB) TX bytes:8268 (8.0 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1104 (1.0 KiB) TX bytes:1104 (1.0 KiB) wlan0 Link encap:Ethernet HWaddr e8:94:f6:19:80:4c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So it seems that the wlan0 USB wireless adapter driver is correctly loaded. If I remove the USB wireless adapter and put it again into the USB port, the lasts lines of dmesg log is: [ 20.303172] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 20.306340] RTL871X: set bssid:00:00:00:00:00:00 [ 20.306726] RTL871X: set ssid [g\xffffffc6isQ\xffffffffJ\xffffffec)\xffffffcd\xffffffba\xffffffba\xffffffab\xfffffff2\xfffffffb\xffffffe3F|\xffffffc2T\xfffffff8\x1b\xffffffe8\xffffffe7\xffffff8dvZ.c3\xffffff9f\xffffffc9\xffffff9a\xffffff9aD\xffffffa7\x1a\xffffffa0\x1a\xffffff8b] fw_state=0x00000008 [ 21.614585] RTL871X: indicate disassoc [ 21.908495] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [ 25.006282] Adding 102396k swap on /var/swap. Priority:-1 extents:1 across:102396k SSFS [ 26.247997] RTL871X: nolinked power save enter As you can see some of these line are related to the RTL871X that is my USB wireless adapter, but I don't know is that these line report an error or if it is all ok. Looking at the adapter status I obtain: pi@raspberrypi ~ $ ip link list dev wlan0 3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DORMANT qlen 1000 link/ether e8:94:f6:19:80:4c brd ff:ff:ff:ff:ff:ff As you can see the mode is DORMANT but I think that this is normal because now I am connected using ethernet. I tryied to set up the adapter but it seems that I obtain no result, infact: pi@raspberrypi ~ $ sudo ip link set dev wlan0 up pi@raspberrypi ~ $ ip link list dev wlan0 3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DORMANT qlen 1000 link/ether e8:94:f6:19:80:4c brd ff:ff:ff:ff:ff:ff pi@raspberrypi ~ $ sudo ip link set dev wlan0 up This is my /etc/network/interfaces file content and it is ok: auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp and it is the /etc/wpa_supplicant/wpa_supplicant.conf that I think is ok (I did not change it compared to when it worked): ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev update_config=1 network={ ssid="MY-NETWORK" psk="mypassword" key_mgmt=WPA-PSK } and infact if I execute a network scan I correctly find MY-NETWORK in the network list,infact: pi@raspberrypi ~ $ sudo iwlist wlan0 scan | grep ESSID ESSID:"TeleTu_74888B0060AD" ESSID:"MY-NETWORK" ESSID:"FASTWEB-1-PT6NtjL4TOSe" ESSID:"DC" So I reboot the system and I remove the ethernet cable but when I try to connect again to my raspberry I obatin the following error message: andrea@andrea-virtual-machine:~$ sudo ssh [email protected] ssh: connect to host 192.168.1.9 port 22: No route to host It seems that it can't connect using wireless. What could be the problem? What am I missing? How can I solve this situation? Tnx

  Read the article

• Ubuntu 10.04 Keyboard and Mouse Freezing Problem

  - by nitbuntu

  I had a partition setup with Windows XP and Ubuntu 8.04 dual booting. I recently upgraded to Ubuntu 10.04 by installing fresh from CD but leaving the previous /home folder as is. Things seemed to be working fine, but started finding that my mouse and keyboard were freezing. After a quick search on the internet, I found the following suggestions as shown here:- Ubuntu Forums Here the suggestion was to:- Edit /etc/default/grub, go to the line that begins like: GRUB_CMDLINE_LINUX_DEFAULT= Change it to: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi=off" After that, run this command: sudo update-grub and Reboot This seemed to have resolved the issue but after a couple of days I again find my mouse and keyboard freezing. I also find that my parallel port printer had also stopped working. I have saved the output of dmesg and my syslog. The first can be viewed here but the syslog had too many characters, so if someone can suggest an alternative to freetexthost, I can post it there. Moreover, if there is any other information that should be provided, do let me know. I do hope we can get to the bottom of this issue. Thank you in advance for any help that could be provided.

  Read the article

• /proc/net/dev and /sys/class/net/ bogus network interface names

  - by sfink

  I am constructing a list of network interfaces to monitor based on the contents of /proc/net/dev. But I am getting some bogus interfaces in the list: __tmp1104705027 __tmp974528607 Where do those come from? They also show up in /sys/class/net/: # ls -1 /sys/class/net/ eth0 eth1 eth2 eth3 lo sit0 __tmp1104705027 __tmp974528607 For now, I think I'll just ignore anything starting with __tmp, but I'd like to know what they are and where they come from. This is on a recompiled CentOS 5.3 kernel: 2.6.18-128.7.1.el5.tvh.7PAE #1 SMP PREEMPT

  Read the article

• open mysql to any connection on ubuntu

  - by ThomasReggi

  I simply want to open up mysql to be accessible from any server ip. I have already commented out the bind-address in /etc/mysql/my.conf. I have already setup the user account within mysql. I have no clue whats stopping me from connecting. The more challenging I see this being the more I realize how much of a security risk it is, and I get that, I just want to be able to do it temporarily. I think that the iptables firewall is the last thing that is preventing me from achieving this, but sudo iptables -A INPUT -p tcp -m tcp --dport 3306 -j ACCEPT is seemingly doing nothing.

  Read the article

• Bad I/O scheduler?

  - by user62367

  os: up-to-date Fedora 14. Working as a "normal desktop". It's doing very well, but if i start VirtualBox, and e.g.: install a guest on it, it just "freezez". I mean if there are disk activities on a VirtualBox guest, then the computer becomes unrespondable..even the mouse is laggin for about 50 minutes.. What could be the bottleneck? What could be the problem? If anyone has any tips/howtos to speed it up, please help! It has a normal 2,5" HDD, with 5400 RPM. Does it worth for me if i buy a 2,5" HDD with 7200 RPM? T7200 cpu, 4 GByte RAM, "vm.swappiness = 0". Thank you!

  Read the article

• Failed to start apache Can't open /etc/apache2/envvars

  - by bumperbox

  i have had this problem a couple of times now and i am not sure what is causing it Failed to start apache : .: 45: Can't open /etc/apache2/envvars when i look at a dir listing, i get these question marks next to envvars, does anyone know what that means? os is ubuntu 10 if that helps drwxr-xr-x 7 root root 4096 Jan 29 11:56 . drwxr-xr-x 83 root root 4096 Feb 4 10:34 .. -rw-r--r-- 1 root root 8113 Sep 29 01:52 apache2.conf -rw-r--r-- 1 root root 8027 Oct 3 22:26 apache2.conf.dpkg-old drwxr-xr-x 2 root root 4096 Jan 29 11:56 conf.d ?????????? ? ? ? ? ? envvars -rw-r--r-- 1 root root 0 Oct 3 22:25 httpd.conf ?????????? ? ? ? ? ? magic drwxr-xr-x 2 root root 4096 Jan 29 11:56 mods-available drwxr-xr-x 2 root root 4096 Jan 29 10:18 mods-enabled ?????????? ? ? ? ? ? ports.conf drwxr-xr-x 2 root root 4096 Jan 29 11:56 sites-available drwxr-xr-x 2 root root 4096 Jan 29 11:55 sites-enabled UPDATE Just heard back from the hosting company, they move my VPS to a new hardware node last night, and something at their end wasn't quite right which caused the issue

  Read the article

• Clients didn't switch to secondary DNS server during fail over

  - by The Digital Ninja

  I have two internal dns servers set up and all my servers have both of them in the resolv.conf Our main dns server went down and suddenly no server could see each other. I edited a few of the servers resolv.conf manually and committed out the first (down) dns server and that machine would instantly be able to ping again. What did I do wrong, does it not auto switch to the secondary dns server when it times out? # File managed by puppet nameserver 192.168.146.100 nameserver 192.168.159.101 ;nameserver 72.14.188.5 domain example.com search example.com

  Read the article

• How to prevent Ubuntu from combining networks on 2 NIC server?

  - by SolarPower

  I've got a Ubuntu Server 10.10 with 2 network interfaces with a cable plugged into both going to switches on completely different networks with different routers. One network is the 10.1.10.X network with a separate gateway/router - the server has an IP of 10.1.10.50 with the gateway IP of 10.1.10.1. The other interface is 10.2.10.X, IP 10.2.10.50, gateway 10.2.10.1. All my Mac machines are on the 10.2.10.X network, and all servers on the 10.1.10.X. The ONLY connection between the two is this machine. From a Mac in my office, I CANNOT ping any computer on the 10.1.10.X network except the Ubuntu machine I'm talking about. However, under the Shared column in Finder, I can see every server on the other network listed. That makes me believe that somehow this Ubuntu machine is letting certain requests span both networks, which is a security problem. Hope this is enough info.

  Read the article

• IPv6 static routes

  - by user98651

  I am looking to configure a few hosts with IPv6 on my network. The router (running CentOS 5) is configured with an Hurricane Electric (HE) tunnel which works fine on that host. However, I would like to statically add a few additional hosts on the same LAN to have IPv6 through this tunnel. No, I don't want radvd or dhcpv6 to do the work for me in this case. I already have IPv6 forwarding enabled in sysctl.conf. I am looking for help with the next steps (statically adding the routes). Lets say the IP addresses are as follows: Router: 2001:470:1b07:1:: Host1: 2001:470:1b07:2:: How would I go about making them see each other? Thanks in advance for the help.

  Read the article

• How to use Google Talk video chat on Redhat?

  - by eSKay

  Is there some way? This page says its not possible 'normally'. Is there a workaround for this?

  Read the article

• RHEL 5/CentOS 5 - sshd becomes unresponsive

  - by ewwhite

  I have a number of CentOS 5.x and RHEL 5.x systems whose SSH daemons become unresponsive, preventing remote logins. The typical error from the connecting side is: $ ssh db1 db1 : ssh_exchange_identification: Connection closed by remote host Examining /var/log/messages after a forced reboot shows the following leading up to the restart: Dec 10 10:45:51 db1 sshd[14593]: fatal: Privilege separation user sshd does not exist Dec 10 10:46:02 db1 sshd[14595]: fatal: Privilege separation user sshd does not exist Dec 10 10:46:54 db1 sshd[14711]: fatal: Privilege separation user sshd does not exist Dec 10 10:47:38 db1 sshd[14730]: fatal: Privilege separation user sshd does not exist These systems use LDAP authentication and the nsswitch.conf file is configured to look at local "files" first. [root@db1 ~]# cat /etc/nsswitch.conf # # /etc/nsswitch.conf # passwd: files ldap shadow: files ldap group: files ldap hosts: files dns The Privilege-separated SSH user exists in the local password file. [root@db1 ~]# grep ssh /etc/passwd sshd:x:74:74:Privilege-separated SSH:/var/empty/sshd:/sbin/nologin Any ideas on what the root cause is? I did not see any Red Hat errata that covers this.

  Read the article

• Monitoring outgoing bandwidth of application

  - by jnolte

  I currently have a VPS that is consuming a ton of outgoing bandwidth and I am trying to drill down to where this may be coming from. Does anyone know of a logical way to go about finding out which pages on the site are consuming the most outgoing data. We have done a ton of front-end optimizations to the site and our google page speed rankings ar 85% so I feel we have done a pretty great job at optimizing the site for speed. Can someone lend some insight on how they have made similar optimizations? Application / Server Stack LEMP Running Varnish Cache / PHP5-FPM WordPress running w3 Total Cache Ubuntu 12.04 LTS

  Read the article

• Bash Script Exits su or ssh Session Rather than Script

  - by Russ

  I am using CentOS 5.4. I created a bash script that does some checking before running any commands. If the check fails, it will simply exit 0. The problem I am having is that on our server, the script will exit the su or ssh session when the exit 0 is called. #!/bin/bash # check if directory has contents and exit if none if [ -z "`ls /ebs_raid/import/*.txt 2>/dev/null`" ]; then echo "ok" exit 0 fi here is the output: [root@ip-10-251-86-31 ebs_raid]# . test.sh ok [russ@ip-10-251-86-31 ebs_raid]$ as you can see, I was removed from my sudo session, if I wasn't in the sudo session, it would have logged me out of my ssh session. I am not sure what I am doing wrong here or where to start.

  Read the article

• How to restore a dd overwritten disk partition?

  - by DairyKnight

  First of all, I admit I'm stupid and I didn't run proper backup of my data, but you know crap happens... So, I've used dd to overwrite the first 2GB of my 750GB NTFS partition with a FAT32 partition. I've run Photorec and EasyRecovery but all I can restore is the 2GB FAT32 partition and the files on that. Is there a way to "roll back" to the NTFS paritition, and recover - at least - some part of the 750GB data? Thanks.

  Read the article

• RHEL 5.3 Kickstart - How specify location of individual package in Workstation folder?

  - by Ed

  I keep getting "package does not exist" errors during the install. I made a kickstart ISO to create an unattended install of a RHEL 5.3 build machine for C++ software releases. It pulls the kickstart config file from our internal web server. This is handy; it makes it easy to test and modify without having to make a new ISO. And I plan to check it in to version control if I can get it working. Anyway, the rpm packages are located in two folders on the disk; Client and Workstation. The packages install fine for the ones that are physically located under the Client folder. It cannot find those under the Workstation folder such as as doxygen and subversion complaining that packages do not exist. Is there a way to specify the individual package location? # ----------------------------------------------------------------------------- # P A C K A G E S # ----------------------------------------------------------------------------- %packages @gnome-desktop @core @base @base-x @printing @development-tools emacs kexec-tools fipscheck xorg-x11-server-Xnest xorg-x11-server-Xvfb #Packages Located in Workstation Folder *** Install can not find any of these ?? bison doxygen gcc-c++ subversion zlib-devel freetype-devel libxml2-devel Thanks in advance, -Ed

  Read the article

< Previous Page | 320 321 322 323 324 325 326 327 328 329 330 331  | Next Page >