Search Results

Search found 40287 results on 1612 pages for 'try statement'.

Page 330/1612 | < Previous Page | 326 327 328 329 330 331 332 333 334 335 336 337  | Next Page >

• My home router randomly disconnects me and I'm unable to reconnect to it

  - by Roy Tang

  It's happened a few times, I'm not sure how to diagnose/debug, so any advise would be appreciated. Symptons: sometimes the router will randomly disconnect; the connection icon on my desktop (wired to the router) gets that yellow "!" symbol that tells me my connection just went down. At this point I'm unable to ping the router. afterwards I try to reset the router by removing then reconnecting the power jack on the router side (this is the fastest way as I can't reset the power strip it's connected to without rebooting my desktop. the router has a reset thingy, but it's one of those things where i have to find a pin to stick into the hole, and when I get disconnected I usually need to get reconnected immediately so I just pull and put back the power jack), but even after that the connection has the same state. after the router reboots, if I try to connect to it using a wifi device like my ipad, the ipad prompts me for the wifi password even though it had already "remembered" all the settings for this router forever after i finally decide to reboot the power strip, and my desktop and the router boot up again, the connection returns to its normal state somewhat and i'm able to connect to it as normal using the desktop and wifi devices. What do I need to check the next time this happens so I can figure out the problem? Is it possibly because we've been using the power jack on the router as an easier way to reboot it? Should I be shopping around for a new router? If it helps, the router is a DLink DIR-300

  Read the article

• Connection failed between Windows Servers

  - by Kerby82

  I'm setting up an infrastructure based on Windows Server 2012. The firewall is turned off and I can't access the Domain controller to check for the group policy. I'm experiencing some connection problem between servers. All the servers are running a site on the TCP Port 80 and I check with netstat that the web server is binding on every Ip of the servers. If i try to telnet from the server itself on the port 80 it works (using DNS name) if I try same telnet from another machine I get connection failed. The DNS works, the ping is successfull, the servers are on the same subnet, the firewall is turned off (even though windows advanced firewall says that some settings can be managed by the System Administrator, i guess group policy). I don't know how to troubleshoot further. Do you have any idea? Is that possible that the FW looks turned off but there are some group policy blocking the connections? (I also check group policy-Administrative Template-Network Connections- Windows FW everything is not configured) I need some hint on how to keep troubleshooting such a problem.

  Read the article

• Browsing \\computer\share fails, but net use \\computer\share works?

  - by JMD

  I've had mixed results with using Windows Explorer to browse remote file shares. The setup: I'm at work on Windows XP SP3 Files are at home on Windows XP SP3 Two separate VPNs are available to access my PC at home corporate OpenVPN (10.1.2.3) a Hamachi/LogMeIn connection (5.1.2.3) With respect to my problem, it doesn't matter which IP I use. They both perform exactly the same way: I expect that if I open Windows Explorer and type in \\10.1.2.3\Shared I should be interrupted with a challenge for credentials, and then be able to interact with the files in the share. However, I just get that annoying dialog, "Windows cannot find '\10.1.2.3\Shared' Check the spelling and try again, or try searching for the item ..." However, I can take that exact same computername/sharename and with net use I can: net use * \\10.1.2.3\Shared * /user:homecomputername\username with this result: Type the password for \\5.69.83.158\C$: Drive Z: is now connected to \\5.69.83.158\C$. The command completed successfully. I can then access the files in Z: in Windows Explorer which was my original intent. Even after Z: is already mapped and the credentials are cached I still cannot bring up \\10.1.2.3\Shared in Windows Explorer. Why does the latter work, but not the former? Edit: Other services work fine, such as RDP. (I have a problem in which I can't SSH home, but I'll consider that separately.)

  Read the article

• Getting Started in SuSE as an Ubuntu User

  - by Subhamoy Sengupta

  I am not a Linux newbie, but haven't touched SuSE in a very very long time (last time I tried it, it was SuSE 7!). Finally now I felt like giving it a try, and many things seem strange or unnecessarily complex. I have a series of questions. How do I ensure that my packages are uptodate? It sounds silly, but I tried the obvious methods already. I have disabled the default repositories that show up when you do zypper lr, and added Tumbleweed and packman repositories (Essentials, Multimedia, Extra). Then I did a sudo zypper ref --force and then sudo zypper dup, and it tells me many dependencies are not met. I have already added solder.allowVendorChange=true to /etc/zypp/zypp.conf, so it should not care which repository the latest versions are in, and just upgrade to it. Even when I chose to skip the packages with unmet dependencies, and seemed like quite a bit happened in the background, I opened Firefox afterwards and the version was 7! I am guessing things did not go as expected. But of course this is not a problem with SuSE, but I am not understanding the system right. How do I do it right? When I start typing arguments of a command, for example sudo zypper install, when I type sudo zypper ins and keep hitting TAB, nothing happens! It always worked in Ubuntu and I feel very uneasy with this. Is this how SuSE is supposed to be? When I try to install something, and I start writing its name, even though the package exists and I am sure of it, hitting TAB does not autocomplete it. This is also quite inconvenient. Why is it not happening? There are many things in SuSE that are really great, and I think I will stay with it and not go back to Ubuntu once I settle these very rudimentary issues. But right now they are giving me a lot of grief! Please help!

  Read the article

• 32bit dll not loading with Enable 32 Bit Applications on IIS 7.5

  - by Jon

  I have a MVC 3 Web Site referencing a 32 bit DLL. The OS is Windows 2008 R2 x64. The website is in the ASP.NET 4 App Pool. I have turned on Enable32Bit but it doesn't work. I get a Bad Image Exception but can't find out to turn this level of logging on in IIS. I have setup up a page that outputs whether it's running 32bit or 64bit and when I turn on/off the Enable32Bit on the AppPool I get the correct output. The website is also in Full Trust. I'm at a loss to try and and get it to work. I do know that it works on Win7 32bit. Can you suggest some things to try? UPDATE: I have just written a simple Windows Forms App with a button on it which calls my DLL. This was built with target of x86 and it worked fine so there is an issue with IIS or ASP.Net I think. UPDATE 2: Does it matter if the ASP.Net Pipeline is Clasic or Integrated? I've tried both but same problem but thought it was worth asking UPDATE 3: I found this question trying to do the same thing and he gave up which isnt too helpful!!

  Read the article

• yum fails installing php53-devel.x86_64

  - by coding_hero

  I need to recompile php on a Fedora server because I need to use the --enable-zip flag. When trying to install the devel package, I get the following message. This is after a 'yum clean all': yum install php53-devel.x86_64 Loaded plugins: rhnplugin, security rhel-x86_64-server-5 | 1.4 kB 00:00 rhel-x86_64-server-5/primary | 4.9 MB 00:00 rhel-x86_64-server-5 14161/14161 Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package php53-devel.x86_64 0:5.3.3-13.el5_8 set to be updated --> Processing Dependency: php53 = 5.3.3-13.el5_8 for package: php53-devel --> Finished Dependency Resolution php53-devel-5.3.3-13.el5_8.x86_64 from rhel-x86_64-server-5 has depsolving problems --> Missing Dependency: php53 = 5.3.3-13.el5_8 is needed by package php53-devel-5.3.3-13.el5_8.x86_64 (rhel-x86_64-server-5) Error: Missing Dependency: php53 = 5.3.3-13.el5_8 is needed by package php53-devel-5.3.3-13.el5_8.x86_64 (rhel-x86_64-server-5) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest Output of 'yum repolist': # yum repolist Loaded plugins: rhnplugin, security repo id repo name status rhel-x86_64-server-5 Red Hat Enterprise Linux (v. 5 for 64-bit x86_64) enabled: 14,161 repolist: 14,161

  Read the article

• what type of laptop do I need to run a amd64 or i386 VM?

  - by Frank Schwieterman

  I was running an amd64 build of Ubuntu on a VM on a Windows host which was also amd64. Later I found I could not run the same amd64 iso on my laptop, which is intel without hyper-V. I was confused I thought chipset mattered, but maybe it does not. When buying a PC or Apple, is there anything to check about the chipset to make sure it can run different types of VMs? In my case, I was trying to run ubuntu on a Thinkpad T520. Per answer below, I did need to enable some bios settings. I'm still having some issues. Running ubuntu on virtual box, when I try to use ubuntu-12.10-server-amd64.iso for the CD/DVD device to start a new VM, virtualbox complains "Failed to open the CD/DVD image . Could not get the storage format of the medium (VERR_NOT_SUPPORTED). When I try to use ubuntu-12.10-server-i386.iso the ISO is accepted, but then the VM complains "FATAL: No bootable medium found! System halted." I had been using an amd64 iso on my home PC which is amd64 and it works fine, which is why I suspected CPU mismatch was the problem at first. But it seems like I'm having issues, and maybe this superuser thread can be used to verify the cpu is irrelevant in this case.

  Read the article

• unicorn and nginx, went wrong

  - by achempion

  I try to deploy my app via capistrano. It was done, but when I start to nginx and show my site in the browser I see 'We're sorry, but something went wrong.' It is bad. I use unicorn. See my configs https://gist.github.com/3904032 I try to start server via rails s -e prodiction and it's work! I think that this error may be because I can't restart server root@li272-194:~# /etc/init.d/nginx restart Restarting nginx: the configuration file /etc/nginx/nginx.conf syntax is ok configuration file /etc/nginx/nginx.conf test is successful [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: still could not bind() nginx. any ideas? nginx log 2012/10/17 02:57:41 [error] 3271#0: *1 could not find named location "@myapp", client: 91.192.62.77, server: 178.79.153.194, request: "GET / HTTP/1.1", host: "178.79.153.194" 2012/10/17 02:19:08 [crit] 2448#0: *8 connect() to unix:/srv/zarcon/shared/unicorn.sock failed (2: No such file or directory) while connecting to upstream, client: 91.192.62.77, server: zarkon, request: "GET / HTTP/1.1", upstream: "http://unix:/srv/zarcon/shared/unicorn.sock:/", host: "178.79.153.194"

  Read the article

• Virtual machine lost after power cut

  - by dannymcc

  We have just had a power issue and our ESX (ESXi 4.1.0) host lost power and then rebooted. All but one of the virtual servers have rebooted with no problem, however one of them refused to power up. I try to power it on and I get the following error: File <unspecified filename> was not found Reason: The system cannot find the file specified. Cannot open the disk '/vmfs/volumes/4e03076e-90834647-b846-001185c38f42/LAMP- Stack/turnkey-lamp-11.3-lucid-x86.vmdk' or one of the snapshot disks it depends on. VMware ESX cannot find the virtual disk "/vmfs/volumes/4e03076e-90834647-b846- 001185c38f42/LAMP-Stack/turnkey-lamp-11.3-lucid-x86.vmdk". Verify the path is valid and try again. I have logged into the ESX host to see if the file is there an have found only the following file that matches the filename: /vmfs/volumes/4e03076e-90834647-b846-001185c38f42/LAMP-Stack/turnkey-lamp-11.3-l ucid-x86-s001.vmdk I notice that the above file has '-s001' after the filename. Is this recoverable? Any help of advice is greatly appreciated! EDIT: Running ls -l on the directory that contains the file shows this: drwxr-xr-t 1 root root 1680 Feb 9 09:49 4e03076e-90834647-b846-001185c38f42 The databrowser file system looks like this: and in a different directory there is the file that matches the missing one:

  Read the article

• Windows 7 System File Checker (sfc) not working

  - by Andrew

  I have a strange problem with Windows 7 RTM. I'm running Ultimate 64-bit edition. Whenever I run sfc /scannow I get this error: Windows Resource Protection could not start the repair service. My research so far has told me that I need to set the Windows Module Installer and Windows Installer services' startup types to Manual. They already were, so I manually started those services and tried again. No luck. I've even booted into my Windows 7 repair disc and tried running sfc /scannow from that. All I get is this: A repair operation is already pending. Restart and try again. History: I'm trying to run sfc because I am unable to open any images in Windows Photo Viewer. Whenever I try, I get the error "Class not registered." I believe the problem started after I installed Gladinet, but I can't be sure. I've uninstalled Gladinet, but the problem remains. System Restore was disabled (yes, I know I'm stupid - you don't have to remind me). Please help. Thanks.

  Read the article

• Ubuntu cannot resolve unmet dependency

  - by DisgruntledGoat

  I'm trying to install a package on my Ubuntu 8.10 server. However, I get this message: The following packages have unmet dependencies. webmin: Depends: apt-show-versions but it is not going to be installed E: Unmet dependencies. Try ‘apt-get -f install’ with no packages (or specify a solution). So I run apt-get -f install which offers to install apt-show-versions and libapt-pkg-perl. After selecting to install without verification, I get these errors: Err http://gb.archive.ubuntu.com intrepid/universe libapt-pkg-perl 0.1.22build1 404 Not Found Err http://gb.archive.ubuntu.com intrepid/universe apt-show-versions 0.13 404 Not Found Failed to fetch http://gb.archive.ubuntu.com/ubuntu/pool/universe/liba/libapt-pkg-perl/libapt-pkg-perl_0.1.22build1_i386.deb 404 Not Found Failed to fetch http://gb.archive.ubuntu.com/ubuntu/pool/universe/a/apt-show-versions/apt-show-versions_0.13_all.deb 404 Not Found E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? I've tried running apt-get update and adding --fix-missing as suggested, but neither works. Where do I go from here?

  Read the article

• Send command through PuTTY automatic login

  - by Arthur

  I am using the following to login automatically to a remote server and then run commands listed in a commands.txt, like this: C:\path to\putty.exe -ssh adreese.ip -l user -pw Password -m C:\Path to\command.txt commands.txt contains the following: wakeonlan -i broadcast adress Macadress However, when I try to do so a new window for PuTTY appears, but it closes and exits instantly after login. As a result, I cannot see the output of the command(s). After a several tests, it appears that the command is not execute , cause my computer doesn't "wake on lan". I don't understand what's going on here ? I cannot use the plink.exe program cause I cannot make connection with public key ( too much distant site for doing all the registration keys in putty ) Can someone help me with this ? Or can i use another program to make ssh connection and send command with script from a windows os? Edit : I also try to make a bash file in the distant server with the same command and execute it from the session like this : C:\path to\putty.exe -ssh adreese.ip -l user -pw Password \home\user\script.sh Ihave the same problem... Need help please : /

  Read the article

• Help trying to figure out why IIS7 is crashing / locking up / denying connections

  - by Pure.Krome

  Hi folks, I've got a pretty busy website that is running on a single web front end machine, on W2K8 + IIS7. Every now and then - eg. maybe monday at 3am or something, then a few days later .. some early morning time .. then nothing for 2 weeks ... etc - the website fails to respond to any client connections. ie. no one can connect to the website. I can remote desktop to the machine, etc no probs. I restart the app pool (the website is running in intergrated mode), still nothing. I try and get a crash dump of the process (it's around 600 mb maybe even more) ... that fails after about a min of trying (and i have plenty of HD space). The only way to fix this issue, is to manually stop the www service and then start it again. The stopping takes a while (a minute?) while starting is nearly instant. I'm at a loss to figure out what part of my code is causing this. At first, I thought it might be a stack overflow because of some error that might be going to the error page, which in turn errors .. rinse repeat boom. But i've had a look at the error page and it feels ok. So, I'm hoping someone might be able to help and say how I can correctly get a proper dump of the IIS process so i can then do some more autopsy on it. I would email Tess Ferrandez (the goddess of crash debuging) but I thought I'd try here before I spam her. Can anyone have any suggestions to how I can figure out how to start to debug this issue?

  Read the article

• How do I set up dual monitors on Kubuntu 10.04 using the latest nVidia drivers with a 9800M video ca

  - by NoCatharsis

  I'm a Linux newb so please try to keep the lingo low-key. I installed the latest nVidia drivers on my laptop using the 9800M card. The laptop is a Gateway P-7805u and I'm connected to the second monitor using VGA. Also, before installing the nVidia drivers (and just using the basic drivers included with Kubuntu 10.04), basic dual monitor support worked, except I could not enable compositing features for some reason. So I thought the proprietary drivers would fix this. Several issues have arisen since installation: 1) I've clicked through all of the display settings to activate the second screen with absolutely no change. 2) When I try to apply settings and Save Configuration as the nVidia help suggests, I am told that I cannot save to the X.conf file. I assume this is due to innate permissions on my user settings, which I have no idea how to properly configure. 3) I have no idea where to go from here, as most of the fixes I found online involve Linux syntax and verbiage, to which I'm totally clueless after spending over half my life with Windows.

  Read the article

• Is Ubuntu a viable replacement of Windows XP for small enterprise environments?

  - by Alex. S.

  Hi all, I'm a newbie systems administrator, so any advice would be great. I would like to setup ubuntu 8.04 lts in a small office of consulting in management (around 50 workstations) instead of Windows XP. I would install MS Office 2007 via WINE (*). It would be a fresh installation, so the migration would be less of a pain. The new setup would also include a small server as document repository and a backup server by now. Later, I would install another goodies like a IM server, a document management solution, and whatnot collaborative tool. What do you advice in this scenario? Do you think is viable? Should I try to convince my managers this is a good idea? I consider myself as a fair experienced user in both systems, and I'm the only guy in charge of everything. I need to cut costs down, and I think that antivirus and antimalware software are a waste of money and time. Is this good idea?, or should I resign and try to lock down the Windows systems and install AV software? Is there anything else in this setup I'm not foreseeing? (*) The only catch in my test machine until now had been that Office SmartArt doesn't work properly, the rest of Office 2007 may seem ok.

  Read the article

• Ubuntu 10.04 network manager issues

  - by Shark

  I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

  Read the article

• How do I start the Workstation Service so I can use `net use`?

  - by nitefrog

  I have a Windows 7 machine that logs into a domain. The machine can net view and see the different shares, but when I try to use, net use * \\name\share, I get an error stating that the service is not started. Yet when I issue a net start, it states the service is already started. My other win7 machines work fine; they can see and use any of the shares. Is there a security setting that needs to be disabled or enabled? I really need to get this working, and I have no other ideas as the other machines have no problem accessing the shares on different systems. The error I am getting is , "The Workstation Service Has Not Been Started", but like I said other machines can connect fine, and when I issue a, "net start workstation", it states the service is already started. In addition the error number I am receiving is 2138. UPDATE: On the machine that is having issues. From the troubled machine if I issue a Net View \\name I can see all the shares on the machine I want to connect to. When I try to net use * \\name\sharename I get the error The Workstation service has not started. I have set both settings sc config lanmanworkstation start = auto and sc config lanmanserver start = auto on the Windows7 computer that is having issues. I have rebooted the computer and still no dice. I can net view any computer on the network and see all shares, but I cannot access any of the shares in which I can see. In the registry under the HKLM\System\CurrentControlSet\Services Both LanmanServer and LanmanWorkstation start is set to 2. Screen capture of net use and view: The Services: This is really weird. What am I missing? It has to be a security setting...

  Read the article

• lenovo x1 carbon windows 8 frequent wifi disconnect issue

  - by hIpPy

  I'm having frequent wifi disconnects on my Lenovo X1 Carbon Touch laptop. I got this laptop 2 months back and it has been happening ever since about 3-5 times a day and 10 times a week on average. I've Frontier Fios internet. Power connected or not does not matter. Once I get disconnected, I try below to connect again in that order: turn Airplane mode on and off, troubleshoot network problems windows troubleshooter), restart the laptop I'd find that the WiFi adapter would get disabled and sometimes windows troubleshooting would help but more than often I'd end up restarting the laptop. A week back, I upgraded my wifi network adapter drivers (now Intel, version 15.5.6.48, 10/3/2012). I still get disconnected frequently but turning Airplane mode on and off gets me connected again. So the driver update did help. Windows 8 is updated. None of the other devices (nexus, iphone phones, nexus7, ipad tablets) would have wifi issues when my laptop would get disconnected. config: Intel(R) Centrino(R) Advanced-N 6205 (WiFi network adapter) Microsoft Windows 8 Pro Microsoft Windows [Version 6.2.9200] x64-based PC LENOVO System Model: 3443CTO X1 Carbon Touch I recently noticed this log message When I got disconnected in event viewer: Your computer was not assigned an address from the network (by the DHCP Server) for the Network Card with network address 0x[XXXXXXXXXXXX]. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server. Any idea?

  Read the article

• Securing NTP: which method to use?

  - by Harry

  Can someone good at NTP configuration please share which method is the best/easiest to implement a secure, tamper-proof version of NTP? Here are some difficulties... I don't have the luxury of having my own stratum 0 time source, so must rely on external time servers. Should I read up on the AutoKey method or should I try to go the MD5 route? Based on what I know about symmetric cryptography, it seems that the MD5 method relies on a pre-agreed set of keys (symmetric cryptography) between the client and the server, and, so, is prone to man-in-the-middle attack. AutoKey, on the other hand, does not appear to work behind a NAT or a masquerading host. Is this still true, by the way? (This reference link is dated 2004, so I'm not sure what is the state of art today.) 4.1 Are public AutoKey-talking time servers available? I browsed through the NTP book by David Mills. The book looks excellent in a way (coming from the NTP creator after all), but the information therein is also overwhelming. I just need to first configure a secure version of NTP and then may be later worry about its architectural and engineering underpinnings. Can someone please wade me through these drowning NTP waters? Don't necessarily need a working config from you, just info on which NTP mode/config to try and may be also a public time server that supports that mode/config. Many thanks, /HS

  Read the article

• Spam or exchange issue?

  - by John

  I am getting an error message to unknow user on my domain. I would like to know is this just a phishing spam email or it was really send from our domain? I have changed our domain name to OURDOMAIN.COM I have Exchange 2010 installed. Body of the email is Delivery has failed to these recipients or distribution lists: sales The recipient's e-mail address was not found in the recipient's e-mail system. Microsoft Exchange will not try to redeliver this message for you. Please check the e-mail address and try resending this message, or provide the following diagnostic text to your system administrator. Sent by Microsoft Exchange Server 2007 Diagnostic information for administrators: Generating server: murraygroup.local [email protected] #550 5.1.1 RESOLVER.ADR.RecipNotFound; not found ## Original message headers: Received: from ironport.mih.co.uk (10.10.29.9) by mih-exca-01.murraygroup.local (10.10.29.133) with Microsoft SMTP Server id 8.3.106.1; Fri, 29 Jun 2012 12:36:12 +0100 Received: from glamf04.netintelligence.com (HELO mailfilter.iomart.com) ([62.128.193.114]) by ironport.mih.co.uk with SMTP; 29 Jun 2012 12:42:48 +0100 Received: from glamta4.netintelligence.com(localhost.localdomain[127.0.0.1]) by mailfilter.iomart.com ; Fri, 29 Jun 2012 12:37:18 BST Received: from [195.43.137.66] ([195.43.137.66]) by glamta4.netintelligence.com (8.13.1/8.12.8) with ESMTP id q5TBbH4j022142 for <[email protected]>; Fri, 29 Jun 2012 12:37:18 +0100 Date: Fri, 29 Jun 2012 12:37:17 +0100 Message-ID: <20120629145229.4C2A817231D8A7958044@SONW> From: Ines Hampton <[email protected]> To: sales <[email protected]> Reply-To: Marguerite Soto <[email protected]> Subject: User sales MIME-Version: 1.0 Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: 7bit Return-Path: [email protected] eporting-MTA: dns;murraygroup.local Received-From-MTA: dns;ironport.mih.co.uk Arrival-Date: Fri, 29 Jun 2012 11:36:12 +0000 Final-Recipient: rfc822;[email protected] Action: failed Status: 5.1.1 Diagnostic-Code: smtp;550 5.1.1 RESOLVER.ADR.RecipNotFound; not found X-Display-Name: sales

  Read the article

• Permission denied (publickey,gssapi-with-mic,password) ssh error

  - by zentenk

  Heads up I'm a noob with linux and networking. I set up a ubuntu server and I have a static ip for my network. When I try to connect to the server at home (external), it prompts me to log in. I supply the correct password (or incorrect pw), I get the error Permission denied, please try again. and after 3 times I get Permission denied (publickey,gssapi-with-mic,password) I am however able to connect with SSH from another computer in the same network with ssh < internal ip of server > I'm connecting with mac os x and my config file is vanilla. Note: During installation of ubuntu it says I don't have a default route or something while doing auto network configuration, but I ignored it and continued the installation, could this be the problem? EDIT: I have tried the below, I have nothing in hosts.allow and also iptables shows the ports that I have allowed, which is 22. I checked the auth.log, and there is nothing when I connect to it remotely (even when it says permission denied). I have tried connecting to it internally and the correct authentication logs show. Any idea whats wrong?

  Read the article

• Host system resets (crashes) when using VMWare or VirtualBox and 64-bit guest systems

  - by sinni800

  I have been trying to install virtual systems on VMWare for a while now and encountered strange behaviour from my PC. The behaviour is as follows: On "automatic" virtualization mode it either outputs a cryptic error message (can MAYBE give later, if I can reproduce) right on startup (before even the BIOS) or it resets the complete HOST system (blackscreen, bios...) If I install a Windows XP on it it works well on "binary translation" mode. If I try installing Linux on it, in "binary translation" mode it crashes 1 or 2 seconds after I hit enter on the GRUB selection screen (after the first page of kernel messages rolled in) Using VirtualBox it crashes right in the BIOS. It gave me a Bluescreen though! 0x00000101: CLOCK_WATCHDOG_TIMEOUT: a clock interrupt was not received on a secondary processor within the allocated time interval NEWS: I tried VirtualBox again and it did not completely crash the computer this time. It gave me a critical error and a log file: http://pastebin.com/yKZSDs91 In conclusion, it will crash instantly if VT-x is activated. If not, it seemingly only crashed if I try to install something with 64 bits. Another update: Yes, it ONLY crashes when the guest is 64 bit! What I tried: Reinstalling Windows (my Windows installation was quite broken so it seemed natural. Didn't work though.) New BIOS What I am certain of: Virtualization extensions are activated in the BIOS What my computer specs are: ASUS P8P67 LE mainboard, newest BIOS/EFI firmware Intel Core i5 2500k Ati Radeon HD 5770 16 GB Corsair 1333mhz DDR3 RAM, 4 X 4 GB

  Read the article

• Ubuntu cannot resolve unmet dependency

  - by DisgruntledGoat

  I'm trying to install a package on my Ubuntu 8.10 server. However, I get this message: The following packages have unmet dependencies. webmin: Depends: apt-show-versions but it is not going to be installed E: Unmet dependencies. Try ‘apt-get -f install’ with no packages (or specify a solution). So I run apt-get -f install which offers to install apt-show-versions and libapt-pkg-perl. After selecting to install without verification, I get these errors: Err http://gb.archive.ubuntu.com intrepid/universe libapt-pkg-perl 0.1.22build1 404 Not Found Err http://gb.archive.ubuntu.com intrepid/universe apt-show-versions 0.13 404 Not Found Failed to fetch http://gb.archive.ubuntu.com/ubuntu/pool/universe/liba/libapt-pkg-perl/libapt-pkg-perl_0.1.22build1_i386.deb 404 Not Found Failed to fetch http://gb.archive.ubuntu.com/ubuntu/pool/universe/a/apt-show-versions/apt-show-versions_0.13_all.deb 404 Not Found E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? I've tried running apt-get update and adding --fix-missing as suggested, but neither works. Where do I go from here?

  Read the article

• nginx: js file loads indifferently every refresh

  - by poymode

  I have this nginx problem wherein a js file in a rails app loads indifferently. Whenever I try to access the JS file in the browser and refresh the page, the scrollbar changes length meaning sometimes it loads half the js page, sometimes the whole and sometimes just a part of it. the js file size is 71K. my nginx server is on different server,separate from my rails app. when I try to access the js file directly through the app server, lets say 10.48.30.150:3000/javascripts/file.js it works fine and doesnt show any half-loaded page. but when I use the nginx server which upstreams the rails app, it shows the indifferent page loads. here is my nginx http conf error_log /usr/local/nginx/logs/error.log; pid /usr/local/nginx/logs/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; server_names_hash_bucket_size 256; access_log /usr/local/nginx/logs/access.log; sendfile on; #tcp_nopush on; keepalive_timeout 0; tcp_nodelay on; #gzip on; #gzip_min_length 4096; #gzip_buffers 16 8k; #gzip_types application/x-javascript text/css text/plain; large_client_header_buffers 4 8k; client_max_body_size 2G; include /usr/local/nginx/conf.d/*.conf; }

  Read the article

• Having trouble with a workaround, for booting from a usb stick, using grub and a minimal linux kernel to load usb drivers

  - by s hanley

  I'm trying to boot from a usb stick. I formatted it to fat32, and later to ext2, and installed dsl on it using unetbootin, and later the usb install guide on dsl wiki (http://www.damnsmalllinux.org/wiki/index.php/Install_to_USB_From_within_Linux). The bios doesn't have a setting for booting from usb. Grub doesn't "see" the usb drive when I use the root and find commands, explained in (http://www.damnsmalllinux.org/wiki/index.php/USB_Booting). This happens even when I set boot from floppy at the top of the boot order. However, my usb keyboard is recognised by the bios and by grub. How can it recognise the keyboard but not the usb drive? Also, the usb led does flash even before grub starts up, so surely something must be happening usb-wise? I am now following an ubuntu guide to booting from a USB stick, using a hdd-based, minimal linux kernel to supply the usb drivers. But I'm having difficulty adapting it to other OSes (slax/dsl/aptosid). I believe I have to alter the initrd.gz file to include usb drivers and then copy that file along with vmlinuz to a partition on my hdd. But, what's the grub command for the kernel line supposed to look like? From the ubuntu example it's: title USB FLASH DRIVE root (hd0,6) kernel /boot/usb-boot/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper noprompt cdrom-detect/try-usb=true persistent initrd /boot/usb-boot/initrd.lz boot Should mine just be: title USB FLASH DRIVE root (hd0,6) kernel /boot/usb-boot/vmlinuz cdrom-detect/try-usb=true initrd /boot/usb-boot/initrd.lz boot

  Read the article

< Previous Page | 326 327 328 329 330 331 332 333 334 335 336 337  | Next Page >