Search Results

Search found 10759 results on 431 pages for 'auto detect'.

Page 337/431 | < Previous Page | 333 334 335 336 337 338 339 340 341 342 343 344  | Next Page >

• Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

  - by Lucas

  I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

  Read the article

• How to Use Sparklines in Excel 2010

  - by DigitalGeekery

  One of the cool features of Excel 2010 is the addition of Sparklines. A Sparkline is basically a little chart displayed in a cell representing your selected data set that allows you to quickly and easily spot trends at a glance. Inserting Sparklines on your Spreadsheet You will find the Sparklines group located on the Insert tab.   Select the cell or cells where you wish to display your Sparklines. Select the type of Sparkline you’d like to add to your spreadsheet. You’ll notice there are three types of Sparklines, Line, Column, and Win/Loss. We’ll select Line for our example. A Create Sparklines pops up and will prompt you to enter a Data Range you are using to create the Sparklines. You’ll notice that the location range (the range where the Sparklines will appear) is already filled in. You can type in the data range manually, or click and drag with your mouse across to select the data range. This will auto-fill the data range for you. Click OK when you are finished.   You will see your Sparklines appear in the desired cells.   Customizing Sparklines Select the one of more of the Sparklines to reveal the Design tab. You can display certain value points like high and low points, negative points, and first and last points by selecting the corresponding options from the Show group. You can also mark all value points by selecting  Markers. Select your desired Sparklines and click one of the included styles from the Style group on the Design tab. Click the down arrow on the lower right corner of the box to display additional pre-defined styles…   or select Sparkline Color or Marker Color options to fully customize your Sparklines. The Axis options allow additional options such as Date Axis Type, Plotting Data Left to Right, and displaying an axis point to represent the zero line in your data with Show Axis. Column Sparklines Column Sparklines display your data in individual columns as opposed to the Line view we’ve been using for our examples. Win/Loss Sparklines Win/Loss shows a basic positive or negative representation of your data set.   You can easily switch between different Sparkline types by simply selecting the current cells (individually or the entire group), and then clicking the desired type on the Design tab. For those that may be more visually oriented, Sparklines can be a wonderful addition to any spreadsheet. Are you just getting started with Office 2010? Check out some of our other great Excel posts such as how to copy worksheets, print only selected areas of a spreadsheet, and how to share data with Excel in Office 2010. Similar Articles Productive Geek Tips Convert a Row to a Column in Excel the Easy WayShare Access Data with Excel in Office 2010Make Excel 2007 Print Gridlines In Workbook FileMake Excel 2007 Always Save in Excel 2003 FormatConvert Older Excel Documents to Excel 2007 Format TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Office 2010 reviewed in depth by Ed Bott FoxClocks adds World Times in your Statusbar (Firefox) Have Fun Editing Photo Editing with Citrify Outlook Connector Upgrade Error Gadfly is a cool Twitter/Silverlight app Enable DreamScene in Windows 7

  Read the article

• IE9 Beta

  - by Daniel Moth

  I've been using Internet Explorer 8 since the early pre-release bits, but I never tried IE9 until today – the day the Beta is available. I downloaded it from here: http://www.beautyoftheweb.com/ The download took longer than what I expected, but I was doing other stuff, so no bother. After coming down, it asked me to reboot my computer. Really hate when apps do that, but I did it anyway. The first time I launched it, it prompted me with a list of add-ons I should disable including the start-up time that I could save fore each one. It even let me configure the prompt so, for example, it won't prompt me again unless an add-on contributes to more than 1 second of the startup time. Cool. First thing I noticed is that the search bar had gone and, as you'd expect, you have to search from the address box. I totally despise this feature. The first thing I've been doing with all versions of IE is to turn off the automatic searching from the address bar and now I have no way of searching if I do that. Ridiculous. The second thing I notice is that the tabs are next to the address bar and cannot be moved to go below it. One word for that decision: appalling (and, no, I didn't accidentally drop an 'e' and added an 'l' in the previous word). The third thing I notice to the right is the favorites button (star icon) and when I click on it, it brings up the favorites explorer under it on the right; then I pin the explorer and it jumps to the left(!). Why move the entry point to this feature to the right instead of leaving it on the left is beyond me (other than wanting to retrain me on what I've been used to for all this time), but the fact that pinning it makes it jump sides is… an "astonishing" design decision. As I browse I notice a little annoying pop up in the bottom left every time I hover over a link; there is no status bar. I correctly guessed to right click at the top and turn on the status bar (which also got rid of the popup thereafter) and while I am at it, I bring back my favorites bar which was hidden by default (and am pleased to see that all my favorites are still there). The next thing I notice, I like: IE9 is fast. No joke, I visit sites and they seem to be loading visibly much faster – try it! Beyond the speed, I am interested to find out what else is new. I searched and found a few good links: What's new in Internet Explorer 9 Internet Explorer 9 Features (check out the links under "Clean") Top Features If you are a developer, check out IE's msdn home for many articles, e.g. this section on Canvas and SVG. Either way: wherever you are, get IE9 Beta now and judge for yourself. If you don't like it, you can always uninstall (which auto-restores the previous version). Comments about this post welcome at the original blog.

  Read the article

• Use Your Favorite Wallpapers in Windows 7 Starter Edition

  - by Asian Angel

  If you have Windows 7 Starter Edition installed on your netbook, the default wallpaper can get old. If you are tired of looking at the default wallpaper, then join us today as we look at changing it with Oceanis Change Background Windows 7. Special Notes This information is quoted directly from the website and needs to be kept in mind when using Oceanis Change Background Windows 7: If the Oceanis Change Background Windows 7 program no longer works properly after installing some Windows Updates, then uninstall and reinstall the Oceanis Change Background Windows 7 program to have it run properly again. If you ever do an in-place upgrade to another higher level edition of Windows 7 in the future, then be sure to uninstall this Oceanis Change Background Windows 7 program first to avoid incompatibility issues with it in the new edition of Windows 7. It was designed to only work in Windows 7 Starter edition. Before There it is…the default wallpaper everyone with the Starter Edition gets stuck with. Some people may not mind it, but if you are one of the people who really wants something different then get ready to rejoice. After The install file for Oceanis is contained in a zip file so you will need to unzip it to get started. The install process is quick and simple but you will need to do a system restart afterwards. Once you have restarted your computer this is what your screen will look like…do not panic and think that this is all there is to it. This is just the Starter Screen and can be easily changed… Note: Oceanis will auto-start with Windows each time. Using either the Desktop Icon or the Start Menu Entry, open up the Oceanis Main Window. You will see the set of four default wallpapers shown here. At this point the best thing to do is browse for the appropriate folder where you have all of those wonderful new wallpapers just waiting to be used. Note: We found Stretch to be the best Picture Position setting on our system. For our example we had three ready and waiting. We decided to try out the Wallpaper Slideshow feature first. We chose a time frame and saved our changes. Here are our three wallpapers as they switched through. This can be much more interesting than the default wallpaper. There was only one quirk that we encountered while using the Slideshow Setting. On occasion if we minimized a non-maximized window there would be a leftover partial image in place of the window. Our suggestion? Go with one wallpaper at a time and the settings shown below. These are the settings that we had terrific luck with…Only one picture selected, Picture Position = Stretch, & Change Picture Every = Every Day. Using these settings, the Starter Edition acted just like any of the other editions with regard to wallpaper management. Conclusion If you have grown tired of looking at the default wallpaper in Windows 7 Starter Edition then you will certainly appreciate what Oceanis Change Background Windows 7 can do to fix that problem. For more ways to customize your Windows 7 Started Edition, be sure to to check out how to personalize Windows 7 Starter. Links Download Oceanis Change Background Windows 7 Similar Articles Productive Geek Tips Windows 7 Welcome Screen Taking Forever? Here’s the Fix (Maybe)Awesome Desktop Wallpapers: The Windows 7 EditionHow To Customize Wallpaper in Windows 7 Starter EditionDesktop Fun: Starship Theme WallpapersDesktop Fun: Underwater Theme Wallpapers TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows Vista style sidebar for Windows 7 Create Nice Charts With These Web Based Tools Track Daily Goals With 42Goals Video Toolbox is a Superb Online Video Editor Fun with 47 charts and graphs Tomorrow is Mother’s Day

  Read the article

• Start fail VMware-Player 3.1.5 on Ubuntu 12.04 32bit

  - by Chris Lee

  Install got no problem but at start of VMWare Player it want to compile and exit with this error: "Unable to build kernel module." Thats the log: Jun 05 00:03:36.153: app-3075712704| Log for VMware Workstation pid=3709 version=7.1.5 build=build-491717 option=Release Jun 05 00:03:36.153: app-3075712704| The process is 32-bit. Jun 05 00:03:36.153: app-3075712704| Host codepage=UTF-8 encoding=UTF-8 Jun 05 00:03:36.153: app-3075712704| Logging to /tmp/vmware-root/setup-3709.log Jun 05 00:03:36.284: app-3075712704| modconf query interface initialized Jun 05 00:03:36.284: app-3075712704| modconf library initialized Jun 05 00:03:36.336: app-3075712704| Your GCC version: 4.6 Jun 05 00:03:36.350: app-3075712704| Your GCC version: 4.6 Jun 05 00:03:36.371: app-3075712704| Your GCC version: 4.6 Jun 05 00:03:36.417: app-3075712704| Your GCC version: 4.6 Jun 05 00:03:36.429: app-3075712704| Your GCC version: 4.6 Jun 05 00:03:36.521: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:36.526: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:36.529: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:36.533: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:36.536: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:36.579: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:36.583: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:36.586: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:36.589: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:36.593: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:36.602: app-3075712704| Your GCC version: 4.6 Jun 05 00:03:36.624: app-3075712704| Your GCC version: 4.6 Jun 05 00:03:39.677: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:39.689: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:39.694: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:39.697: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:39.701: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:39.711: app-3075712704| Your GCC version: 4.6 Jun 05 00:03:39.733: app-3075712704| Your GCC version: 4.6 Jun 05 00:03:39.854: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:39.858: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:39.862: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:39.865: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:39.868: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:40.065: app-3075712704| Trying to find a suitable PBM set for kernel 3.2.0-24-generic-pae. Jun 05 00:03:40.066: app-3075712704| Building module vmmon. Jun 05 00:03:40.066: app-3075712704| Extracting the sources of the vmmon module. Jun 05 00:03:40.075: app-3075712704| Building module with command: /usr/bin/make -C /tmp/vmware-root/modules/vmmon-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-24-generic-pae/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 Jun 05 00:03:42.016: app-3075712704| Failed to compile module vmmon! Is it a gcc problem ?

  Read the article

• SPARC T5-4 LDoms for RAC and WebLogic Clusters

  - by Jeff Taylor-Oracle

  I wanted to use two Oracle SPARC T5-4 servers to simultaneously host both Oracle RAC and a WebLogic Server Cluster. I chose to use Oracle VM Server for SPARC to create a cluster like this: There are plenty of trade offs and decisions that need to be made, for example: Rather than configuring the system by hand, you might want to use an Oracle SuperCluster T5-8 My configuration is similar to jsavit's: Availability Best Practices - Example configuring a T5-8 but I chose to ignore some of the advice. Maybe I should have included an  alternate service domain, but I decided that I already had enough redundancy Both Oracle SPARC T5-4 servers were to be configured like this: Cntl 0.25  4  64GB                     App LDom                    2.75 CPU's                                        44 cores                                          704 GB              DB LDom      One CPU         16 cores         256 GB   The systems started with everything in the primary domain: # ldm list NAME             STATE      FLAGS   CONS    VCPU  MEMORY   UTIL  NORM  UPTIME primary          active     -n-c--  UART    512   1023G    0.0%  0.0%  11m # ldm list-spconfig factory-default [current] primary # ldm list -o core,memory,physio NAME              primary           CORE     CID    CPUSET     0      (0, 1, 2, 3, 4, 5, 6, 7)     1      (8, 9, 10, 11, 12, 13, 14, 15)     2      (16, 17, 18, 19, 20, 21, 22, 23) -- SNIP     62     (496, 497, 498, 499, 500, 501, 502, 503)     63     (504, 505, 506, 507, 508, 509, 510, 511) MEMORY     RA               PA               SIZE                 0x30000000       0x30000000       255G     0x80000000000    0x80000000000    256G     0x100000000000   0x100000000000   256G     0x180000000000   0x180000000000   256G # Give this memory block to the DB LDom IO     DEVICE                           PSEUDONYM        OPTIONS     pci@300                          pci_0                pci@340                          pci_1                pci@380                          pci_2                pci@3c0                          pci_3                pci@400                          pci_4                pci@440                          pci_5                pci@480                          pci_6                pci@4c0                          pci_7                pci@300/pci@1/pci@0/pci@6        /SYS/RCSA/PCIE1     pci@300/pci@1/pci@0/pci@c        /SYS/RCSA/PCIE2     pci@300/pci@1/pci@0/pci@4/pci@0/pci@c /SYS/MB/SASHBA0     pci@300/pci@1/pci@0/pci@4/pci@0/pci@8 /SYS/RIO/NET0        pci@340/pci@1/pci@0/pci@6        /SYS/RCSA/PCIE3     pci@340/pci@1/pci@0/pci@c        /SYS/RCSA/PCIE4     pci@380/pci@1/pci@0/pci@a        /SYS/RCSA/PCIE9     pci@380/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE10     pci@3c0/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE11     pci@3c0/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE12     pci@400/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE5     pci@400/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE6     pci@440/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE7     pci@440/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE8     pci@480/pci@1/pci@0/pci@a        /SYS/RCSA/PCIE13     pci@480/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE14     pci@4c0/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE15     pci@4c0/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE16     pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c /SYS/MB/SASHBA1     pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4 /SYS/RIO/NET2    Added an additional service processor configuration: # ldm add-spconfig split # ldm list-spconfig factory-default primary split [current] And removed many of the resources from the primary domain: # ldm start-reconf primary # ldm set-core 4 primary # ldm set-memory 32G primary # ldm rm-io pci@340 primary # ldm rm-io pci@380 primary # ldm rm-io pci@3c0 primary # ldm rm-io pci@400 primary # ldm rm-io pci@440 primary # ldm rm-io pci@480 primary # ldm rm-io pci@4c0 primary # init 6 Needed to add resources to the guest domains: # ldm add-domain db # ldm set-core cid=`seq -s"," 48 63` db # ldm add-memory mblock=0x180000000000:256G db # ldm add-io pci@480 db # ldm add-io pci@4c0 db # ldm add-domain app # ldm set-core 44 app # ldm set-memory 704G  app # ldm add-io pci@340 app # ldm add-io pci@380 app # ldm add-io pci@3c0 app # ldm add-io pci@400 app # ldm add-io pci@440 app Needed to set up services: # ldm add-vds primary-vds0 primary # ldm add-vcc port-range=5000-5100 primary-vcc0 primary Needed to add a virtual network port for the WebLogic application domain: # ipadm NAME              CLASS/TYPE STATE        UNDER      ADDR lo0               loopback   ok           --         --    lo0/v4         static     ok           --         ...    lo0/v6         static     ok           --         ... net0              ip         ok           --         ...    net0/v4        static     ok           --         xxx.xxx.xxx.xxx/24    net0/v6        addrconf   ok           --         ....    net0/v6        addrconf   ok           --         ... net8              ip         ok           --         --    net8/v4        static     ok           --         ... # dladm show-phys LINK              MEDIA                STATE      SPEED  DUPLEX    DEVICE net1              Ethernet             unknown    0      unknown   ixgbe1 net0              Ethernet             up         1000   full      ixgbe0 net8              Ethernet             up         10     full      usbecm2 # ldm add-vsw net-dev=net0 primary-vsw0 primary # ldm add-vnet vnet1 primary-vsw0 app Needed to add a virtual disk to the WebLogic application domain: # format Searching for disks...done AVAILABLE DISK SELECTIONS:        0. c0t5000CCA02505F874d0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB>           /scsi_vhci/disk@g5000cca02505f874           /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD0/disk        1. c0t5000CCA02506C468d0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB>           /scsi_vhci/disk@g5000cca02506c468           /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD1/disk        2. c0t5000CCA025067E5Cd0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB>           /scsi_vhci/disk@g5000cca025067e5c           /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD2/disk        3. c0t5000CCA02506C258d0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB>           /scsi_vhci/disk@g5000cca02506c258           /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD3/disk Specify disk (enter its number): ^C # ldm add-vdsdev /dev/dsk/c0t5000CCA02506C468d0s2 HDD1@primary-vds0 # ldm add-vdisk HDD1 HDD1@primary-vds0 app Add some additional spice to the pot: # ldm set-variable auto-boot\\?=false db # ldm set-variable auto-boot\\?=false app # ldm set-var boot-device=HDD1 app Bind the logical domains: # ldm bind db # ldm bind app At the end of the process, the system is set up like this: # ldm list -o core,memory,physio NAME             primary          CORE     CID    CPUSET     0      (0, 1, 2, 3, 4, 5, 6, 7)     1      (8, 9, 10, 11, 12, 13, 14, 15)     2      (16, 17, 18, 19, 20, 21, 22, 23)     3      (24, 25, 26, 27, 28, 29, 30, 31) MEMORY     RA               PA               SIZE                0x30000000       0x30000000       32G IO     DEVICE                           PSEUDONYM        OPTIONS     pci@300                          pci_0               pci@300/pci@1/pci@0/pci@6        /SYS/RCSA/PCIE1     pci@300/pci@1/pci@0/pci@c        /SYS/RCSA/PCIE2     pci@300/pci@1/pci@0/pci@4/pci@0/pci@c /SYS/MB/SASHBA0     pci@300/pci@1/pci@0/pci@4/pci@0/pci@8 /SYS/RIO/NET0   ------------------------------------------------------------------------------ NAME             app              CORE     CID    CPUSET     4      (32, 33, 34, 35, 36, 37, 38, 39)     5      (40, 41, 42, 43, 44, 45, 46, 47)     6      (48, 49, 50, 51, 52, 53, 54, 55)     7      (56, 57, 58, 59, 60, 61, 62, 63)     8      (64, 65, 66, 67, 68, 69, 70, 71)     9      (72, 73, 74, 75, 76, 77, 78, 79)     10     (80, 81, 82, 83, 84, 85, 86, 87)     11     (88, 89, 90, 91, 92, 93, 94, 95)     12     (96, 97, 98, 99, 100, 101, 102, 103)     13     (104, 105, 106, 107, 108, 109, 110, 111)     14     (112, 113, 114, 115, 116, 117, 118, 119)     15     (120, 121, 122, 123, 124, 125, 126, 127)     16     (128, 129, 130, 131, 132, 133, 134, 135)     17     (136, 137, 138, 139, 140, 141, 142, 143)     18     (144, 145, 146, 147, 148, 149, 150, 151)     19     (152, 153, 154, 155, 156, 157, 158, 159)     20     (160, 161, 162, 163, 164, 165, 166, 167)     21     (168, 169, 170, 171, 172, 173, 174, 175)     22     (176, 177, 178, 179, 180, 181, 182, 183)     23     (184, 185, 186, 187, 188, 189, 190, 191)     24     (192, 193, 194, 195, 196, 197, 198, 199)     25     (200, 201, 202, 203, 204, 205, 206, 207)     26     (208, 209, 210, 211, 212, 213, 214, 215)     27     (216, 217, 218, 219, 220, 221, 222, 223)     28     (224, 225, 226, 227, 228, 229, 230, 231)     29     (232, 233, 234, 235, 236, 237, 238, 239)     30     (240, 241, 242, 243, 244, 245, 246, 247)     31     (248, 249, 250, 251, 252, 253, 254, 255)     32     (256, 257, 258, 259, 260, 261, 262, 263)     33     (264, 265, 266, 267, 268, 269, 270, 271)     34     (272, 273, 274, 275, 276, 277, 278, 279)     35     (280, 281, 282, 283, 284, 285, 286, 287)     36     (288, 289, 290, 291, 292, 293, 294, 295)     37     (296, 297, 298, 299, 300, 301, 302, 303)     38     (304, 305, 306, 307, 308, 309, 310, 311)     39     (312, 313, 314, 315, 316, 317, 318, 319)     40     (320, 321, 322, 323, 324, 325, 326, 327)     41     (328, 329, 330, 331, 332, 333, 334, 335)     42     (336, 337, 338, 339, 340, 341, 342, 343)     43     (344, 345, 346, 347, 348, 349, 350, 351)     44     (352, 353, 354, 355, 356, 357, 358, 359)     45     (360, 361, 362, 363, 364, 365, 366, 367)     46     (368, 369, 370, 371, 372, 373, 374, 375)     47     (376, 377, 378, 379, 380, 381, 382, 383) MEMORY     RA               PA               SIZE                0x30000000       0x830000000      192G     0x4000000000     0x80000000000    256G     0x8080000000     0x100000000000   256G IO     DEVICE                           PSEUDONYM        OPTIONS     pci@340                          pci_1               pci@380                          pci_2               pci@3c0                          pci_3               pci@400                          pci_4               pci@440                          pci_5               pci@340/pci@1/pci@0/pci@6        /SYS/RCSA/PCIE3     pci@340/pci@1/pci@0/pci@c        /SYS/RCSA/PCIE4     pci@380/pci@1/pci@0/pci@a        /SYS/RCSA/PCIE9     pci@380/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE10     pci@3c0/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE11     pci@3c0/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE12     pci@400/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE5     pci@400/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE6     pci@440/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE7     pci@440/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE8 ------------------------------------------------------------------------------ NAME             db               CORE     CID    CPUSET     48     (384, 385, 386, 387, 388, 389, 390, 391)     49     (392, 393, 394, 395, 396, 397, 398, 399)     50     (400, 401, 402, 403, 404, 405, 406, 407)     51     (408, 409, 410, 411, 412, 413, 414, 415)     52     (416, 417, 418, 419, 420, 421, 422, 423)     53     (424, 425, 426, 427, 428, 429, 430, 431)     54     (432, 433, 434, 435, 436, 437, 438, 439)     55     (440, 441, 442, 443, 444, 445, 446, 447)     56     (448, 449, 450, 451, 452, 453, 454, 455)     57     (456, 457, 458, 459, 460, 461, 462, 463)     58     (464, 465, 466, 467, 468, 469, 470, 471)     59     (472, 473, 474, 475, 476, 477, 478, 479)     60     (480, 481, 482, 483, 484, 485, 486, 487)     61     (488, 489, 490, 491, 492, 493, 494, 495)     62     (496, 497, 498, 499, 500, 501, 502, 503)     63     (504, 505, 506, 507, 508, 509, 510, 511) MEMORY     RA               PA               SIZE                0x80000000       0x180000000000   256G IO     DEVICE                           PSEUDONYM        OPTIONS     pci@480                          pci_6               pci@4c0                          pci_7               pci@480/pci@1/pci@0/pci@a        /SYS/RCSA/PCIE13     pci@480/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE14     pci@4c0/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE15     pci@4c0/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE16     pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c /SYS/MB/SASHBA1     pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4 /SYS/RIO/NET2   Start the domains: # ldm start app LDom app started # ldm start db LDom db started Make sure to start the vntsd service that was created, above. # svcs -a | grep ldo disabled        8:38:38 svc:/ldoms/vntsd:default online          8:38:58 svc:/ldoms/agents:default online          8:39:25 svc:/ldoms/ldmd:default # svcadm enable vntsd Now use the MAC address to configure the Solaris 11 Automated Installation. Database Logical Domain # telnet localhost 5000 {0} ok devalias screen                   /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@7/display@0 disk7                    /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p3 disk6                    /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p2 disk5                    /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p1 disk4                    /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p0 scsi1                    /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0 net3                     /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4/network@0,1 net2                     /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4/network@0 virtual-console          /virtual-devices/console@1 name                     aliases {0} ok boot net2 Boot device: /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4/network@0  File and args: 1000 Mbps full duplex Link up Requesting Internet Address for xx:xx:xx:xx:xx:xx Requesting Internet Address for xx:xx:xx:xx:xx:xx WLS Logical Domain # telnet localhost 5001 {0} ok devalias hdd1                     /virtual-devices@100/channel-devices@200/disk@0 vnet1                    /virtual-devices@100/channel-devices@200/network@0 net                      /virtual-devices@100/channel-devices@200/network@0 disk                     /virtual-devices@100/channel-devices@200/disk@0 virtual-console          /virtual-devices/console@1 name                     aliases {0} ok boot net Boot device: /virtual-devices@100/channel-devices@200/network@0  File and args: Requesting Internet Address for xx:xx:xx:xx:xx:xx Requesting Internet Address for xx:xx:xx:xx:xx:xx Repeat the process for the second SPARC T5-4, install Solaris, RAC and WebLogic Cluster, and you are ready to go. Maybe buying a SuperCluster would have been easier.

  Read the article

• ORA-4031 Troubleshooting

  - by [email protected]

    QUICKLINK: Note 396940.1 Troubleshooting and Diagnosing ORA-4031 Error Note 1087773.1 : ORA-4031 Diagnostics Tools [Video]   Have you observed an ORA-04031 error reported in your alert log? An ORA-4031 error is raised when memory is unavailable for use or reuse in the System Global Area (SGA).  The error message will indicate the memory pool getting errors and high level information about what kind of allocation failed and how much memory was unavailable.  The challenge with ORA-4031 analysis is that the error and associated trace is for a "victim" of the problem.   The failing code ran into the memory limitation, but in almost all cases it was not part of the root problem.    Looking for the best way to diagnose? When an ORA-4031 error occurs, a trace file is raised and noted in the alert log if the process experiencing the error is a background process.   User processes may experience errors without reports in the alert log or traces generated.   The V$SHARED_POOL_RESERVED view will show reports of misses for memory over the life of the database. Diagnostics scripts are available in Note 430473.1 to help in analysis of the problem.  There is also a training video on using and interpreting the script data Note 1087773.1. 11g DiagnosabilityStarting with Oracle Database 11g Release 1, the Diagnosability infrastructure was introduced which places traces and core files into a location controlled by the DIAGNOSTIC_DEST initialization parameter when an incident, such as an ORA-4031 occurs. For earlier versions, the trace file will be written to either USER_DUMP_DEST (if the error was caught in a user process) or BACKGROUND_DUMP_DEST (if the error was caught in a background process like PMON or SMON). The trace file contains vital information about what led to the error condition.  Note 443529.1 11g Quick Steps to Package and Send Critical Error Diagnostic Information to Support[Video]Oracle Configuration Manager (OCM)Oracle Configuration Manager (OCM) works with My Oracle Support to enable proactive support capability that helps you organize, collect and manage your Oracle configurations.Oracle Configuration Manager Quick Start GuideNote 548815.1: My Oracle Support Configuration Management FAQ Note 250434.1: BULLETIN: Learn More About My Oracle Support Configuration Manager    Common Causes/Solutions The ORA-4031 can occur for many different reasons.  Some possible causes are: SGA components too small for workload Auto-tuning issues Fragmentation due to application design Bug/leaks in memory allocationsFor more on the 4031 and how this affects the SGA, see Note 396940.1 Troubleshooting and Diagnosing ORA-4031 Error Because of the multiple potential causes, it is important to gather enough diagnostics so that an appropriate solution can be identified.  However, most commonly the cause is associated with configuration tuning.   Ensuring that MEMORY_TARGET or SGA_TARGET are large enough to accommodate workload can get around many scenarios.  The default trace associated with the error provides very high level information about the memory problem and the "victim" that ran into the issue.   The data in the default trace is not going to point to the root cause of the problem. When migrating from 9i to 10g and higher, it is necessary to increase the size of the Shared Pool due to changes in the basic design of the shared memory area. Note 270935.1 Shared pool sizing in 10gNOTE: Diagnostics on the errors should be investigated as close to the time of the error(s) as possible.  If you must restart a database, it is not feasible to diagnose the problem until the database has matured and/or started seeing the problems again. Note 801787.1 Common Cause for ORA-4031 in 10gR2, Excess "KGH: NO ACCESS" Memory Allocation ***For reference to the content in this blog, refer to Note.1088239.1 Master Note for Diagnosing ORA-4031 

  Read the article

• SQL SERVER – Partition Parallelism Support in expressor 3.6

  - by pinaldave

  I am very excited to learn that there is a new version of expressor’s data integration platform coming out in March of this year.  It will be version 3.6, and I look forward to using it and telling everyone about it.  Let me describe a little bit more about what will be so great in expressor 3.6: Greatly enhanced user interface Parallel Processing Bulk Artifact Upgrading The User Interface First let me cover the most obvious enhancements. The expressor Studio user interface (UI) has had some significant work done. Kudos to the expressor Engineering team; the entire UI is a visual masterpiece that is very responsive and intuitive. The improvements are more than just eye candy; they provide significant productivity gains when developing expressor Dataflows. Operator shape icons now include a description that identifies the function of each operator, instead of having to guess at the function by the icon. Operator shapes and highlighting depict the current function and status: Disabled, enabled, complete, incomplete, and error. Each status displays an appropriate message in the message panel with correction suggestions. Floating or docking property panels provide descriptive tool tips for each property as well as auto resize when adjusting the canvas, without having to search Help or the need to scroll around to get access to the property. Progress and status indicators let you know when an operation is working. “No limit” canvas with snap-to-grid allows automatic sizing and accurate positioning when you have numerous operators in the Dataflow. The inline tool bar offers quick access to pan, zoom, fit and overview functions. Selecting multiple artifacts with a right click context allows you to easily manage your workspace more efficiently. Partitioning and Parallel Processing Partitioning allows each operator to process multiple subsets of records in parallel as opposed to processing all records that flow through that operator in a single sequential set. This capability allows the user to configure the expressor Dataflow to run in a way that most efficiently utilizes the resources of the hardware where the Dataflow is running. Partitions can exist in most individual operators. Using partitions increases the speed of an expressor data integration application, therefore improving performance and load times. With the expressor 3.6 Enterprise Edition, expressor simplifies enabling parallel processing by adding intuitive partition settings that are easy to configure. Bulk Artifact Upgrading Bulk Artifact Upgrading sounds a bit intimidating, but it actually is not and it is a welcome addition to expressor Studio. In past releases, users were prompted to confirm that they wanted to upgrade their individual artifacts only when opened. This was a cumbersome and repetitive process. Now with bulk artifact upgrading, a user can easily select what artifact or group of artifacts to upgrade all at once. As you can see, there are many new features and upgrade options that will prove to make expressor Studio quicker and more efficient.  I hope I’m not the only one who is excited about all these new upgrades, and that I you try expressor and share your experience with me. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Performance, SQL Query, SQL Server, SQL Tips and Tricks, SQLServer, T SQL, Technology

  Read the article

• Sprite animation in openGL - Some frames are being skipped

  - by Sid

  Earlier, I was facing problems on implementing sprite animation in openGL ES. Now its being sorted up. But the problem that i am facing now is that some of my frames are being skipped when a bullet(a circle) strikes on it. What I need : A sprite animation should stop at the last frame without skipping any frame. What I did : Collision Detection function and working properly. PS : Everything is working fine but i want to implement the animation in OPENGL ONLY. Canvas won't work in my case. ------------------------ EDIT----------------------- My sprite sheet. Consider the animation from Left to right and then from top to bottom Here is an image for a better understanding. My spritesheet ... class FragileSquare{ FloatBuffer fVertexBuffer, mTextureBuffer; ByteBuffer mColorBuff; ByteBuffer mIndexBuff; int[] textures = new int[1]; public boolean beingHitFromBall = false; int numberSprites = 20; int columnInt = 4; //number of columns as int float columnFloat = 4.0f; //number of columns as float float rowFloat = 5.0f; int oldIdx; public FragileSquare() { // TODO Auto-generated constructor stub float vertices [] = {-1.0f,1.0f, //byte index 0 1.0f, 1.0f, //byte index 1 //byte index 2 -1.0f, -1.0f, 1.0f,-1.0f}; //byte index 3 float textureCoord[] = { 0.0f,0.0f, 0.25f,0.0f, 0.0f,0.20f, 0.25f,0.20f }; byte indices[] = {0, 1, 2, 1, 2, 3 }; ByteBuffer byteBuffer = ByteBuffer.allocateDirect(4*2 * 4); // 4 vertices, 2 co-ordinates(x,y) 4 for converting in float byteBuffer.order(ByteOrder.nativeOrder()); fVertexBuffer = byteBuffer.asFloatBuffer(); fVertexBuffer.put(vertices); fVertexBuffer.position(0); ByteBuffer byteBuffer2 = ByteBuffer.allocateDirect(textureCoord.length * 4); byteBuffer2.order(ByteOrder.nativeOrder()); mTextureBuffer = byteBuffer2.asFloatBuffer(); mTextureBuffer.put(textureCoord); mTextureBuffer.position(0); } public void draw(GL10 gl){ gl.glFrontFace(GL11.GL_CW); gl.glEnableClientState(GL10.GL_VERTEX_ARRAY); gl.glVertexPointer(1,GL10.GL_FLOAT, 0, fVertexBuffer); gl.glEnable(GL10.GL_TEXTURE_2D); if(MyRender.flag2==1){ /** Collision has taken place*/ int idx = oldIdx==(numberSprites-1) ? (numberSprites-1) : (int)((System.currentTimeMillis()%(200*numberSprites))/200); gl.glMatrixMode(GL10.GL_TEXTURE); gl.glTranslatef((idx%columnInt)/columnFloat, (idx/columnInt)/rowFloat, 0); gl.glMatrixMode(GL10.GL_MODELVIEW); oldIdx = idx; } gl.glEnable(GL10.GL_BLEND); gl.glBlendFunc(GL10.GL_SRC_ALPHA, GL10.GL_ONE_MINUS_SRC_ALPHA); gl.glBindTexture(GL10.GL_TEXTURE_2D, textures[0]); //4 gl.glTexCoordPointer(2, GL10.GL_FLOAT,0, mTextureBuffer); //5 gl.glEnableClientState(GL10.GL_TEXTURE_COORD_ARRAY); gl.glDrawArrays(GL10.GL_TRIANGLE_STRIP, 0, 4); //7 gl.glFrontFace(GL11.GL_CCW); gl.glDisableClientState(GL10.GL_VERTEX_ARRAY); gl.glDisableClientState(GL10.GL_TEXTURE_COORD_ARRAY); gl.glMatrixMode(GL10.GL_TEXTURE); gl.glLoadIdentity(); gl.glMatrixMode(GL10.GL_MODELVIEW); } public void loadFragileTexture(GL10 gl, Context context, int resource) { Bitmap bitmap = BitmapFactory.decodeResource(context.getResources(), resource); gl.glGenTextures(1, textures, 0); gl.glBindTexture(GL10.GL_TEXTURE_2D, textures[0]); gl.glTexParameterf(GL10.GL_TEXTURE_2D, GL10.GL_TEXTURE_MIN_FILTER, GL10.GL_LINEAR); gl.glTexParameterf(GL10.GL_TEXTURE_2D, GL10.GL_TEXTURE_MAG_FILTER, GL10.GL_LINEAR); gl.glTexParameterf(GL10.GL_TEXTURE_2D, GL10.GL_TEXTURE_WRAP_S, GL10.GL_REPEAT); gl.glTexParameterf(GL10.GL_TEXTURE_2D, GL10.GL_TEXTURE_WRAP_T, GL10.GL_REPEAT); GLUtils.texImage2D(GL10.GL_TEXTURE_2D, 0, bitmap, 0); bitmap.recycle(); }

  Read the article

• Why you shouldn't add methods to interfaces in APIs

  - by Simon Cooper

  It is an oft-repeated maxim that you shouldn't add methods to a publically-released interface in an API. Recently, I was hit hard when this wasn't followed. As part of the work on ApplicationMetrics, I've been implementing auto-reporting of MVC action methods; whenever an action was called on a controller, ApplicationMetrics would automatically report it without the developer needing to add manual ReportEvent calls. Fortunately, MVC provides easy hook when a controller is created, letting me log when it happens - the IControllerFactory interface. Now, the dll we provide to instrument an MVC webapp has to be compiled against .NET 3.5 and MVC 1, as the lowest common denominator. This MVC 1 dll will still work when used in an MVC 2, 3 or 4 webapp because all MVC 2+ webapps have a binding redirect redirecting all references to previous versions of System.Web.Mvc to the correct version, and type forwards taking care of any moved types in the new assemblies. Or at least, it should. IControllerFactory In MVC 1 and 2, IControllerFactory was defined as follows: public interface IControllerFactory { IController CreateController(RequestContext requestContext, string controllerName); void ReleaseController(IController controller); } So, to implement the logging controller factory, we simply wrap the existing controller factory: internal sealed class LoggingControllerFactory : IControllerFactory { private readonly IControllerFactory m_CurrentController; public LoggingControllerFactory(IControllerFactory currentController) { m_CurrentController = currentController; } public IController CreateController( RequestContext requestContext, string controllerName) { // log the controller being used FeatureSessionData.ReportEvent("Controller used:", controllerName); return m_CurrentController.CreateController(requestContext, controllerName); } public void ReleaseController(IController controller) { m_CurrentController.ReleaseController(controller); } } Easy. This works as expected in MVC 1 and 2. However, in MVC 3 this type was throwing a TypeLoadException, saying a method wasn't implemented. It turns out that, in MVC 3, the definition of IControllerFactory was changed to this: public interface IControllerFactory { IController CreateController(RequestContext requestContext, string controllerName); SessionStateBehavior GetControllerSessionBehavior( RequestContext requestContext, string controllerName); void ReleaseController(IController controller); } There's a new method in the interface. So when our MVC 1 dll was redirected to reference System.Web.Mvc v3, LoggingControllerFactory tried to implement version 3 of IControllerFactory, was missing the GetControllerSessionBehaviour method, and so couldn't be loaded by the CLR. Implementing the new method Fortunately, there was a workaround. Because interface methods are normally implemented implicitly in the CLR, if we simply declare a virtual method matching the signature of the new method in MVC 3, then it will be ignored in MVC 1 and 2 and implement the extra method in MVC 3: internal sealed class LoggingControllerFactory : IControllerFactory { ... public virtual SessionStateBehaviour GetControllerSessionBehaviour( RequestContext requestContext, string controllerName) {} ... } However, this also has problems - the SessionStateBehaviour type only exists in .NET 4, and we're limited to .NET 3.5 by support for MVC 1 and 2. This means that the only solutions to support all MVC versions are: Construct the LoggingControllerFactory type at runtime using reflection Produce entirely separate dlls for MVC 1&2 and MVC 3. Ugh. And all because of that blasted extra method! Another solution? Fortunately, in this case, there is a third option - System.Web.Mvc also provides a DefaultControllerFactory type that can provide the implementation of GetControllerSessionBehaviour for us in MVC 3, while still allowing us to override CreateController and ReleaseController. However, this does mean that LoggingControllerFactory won't be able to wrap any calls to GetControllerSessionBehaviour. This is an acceptable bug, given the other options, as very few developers will be overriding GetControllerSessionBehaviour in their own custom controller factory. So, if you're providing an interface as part of an API, then please please please don't add methods to it. Especially if you don't provide a 'default' implementing type. Any code compiled against the previous version that can't be updated will have some very tough decisions to make to support both versions.

  Read the article

• Building ATLAS (and later Octave w/ ATLAS)

  - by David Parks

  I'm trying to set up ATLAS (so I can later compile octave with ATLAS support). If I'm correct, I still need to build this manually due to the environment specific optimizations. I do see a package for ATLAS, but it looks like it's using the cross platform generic build options (e.g. "it'll be slow"). So, running the configure script as described in the docs seems to go poorly. As a java developer I never do well at making heads or tails of errors in these build processes. Am I missing dependencies (if so is there any documentation on what I need)? allusers@vbubuntu:~/Downloads/atlas3.10.1/build_vbubuntu$ ../configure -b 64 -D c -DPentiumCPS=3000 --with-netlib-lapack-tarfile=/home/allusers/Downloads/lapack-3.5.0.tgz make: `xconfig' is up to date. ./xconfig -d s /home/allusers/Downloads/atlas3.10.1/build_vbubuntu/../ -d b /home/allusers/Downloads/atlas3.10.1/build_vbubuntu -b 64 -D c -DPentiumCPS=3000 -Si lapackref 1 OS configured as Linux (1) Assembly configured as GAS_x8664 (2) Vector ISA Extension configured as SSE3 (6,448) ERROR: enum fam=3, chip=2, mach=0 make[3]: *** [atlas_run] Error 44 make[2]: *** [IRunArchInfo_x86] Error 2 Architecture configured as Corei1 (25) ERROR: enum fam=3, chip=2, mach=0 make[3]: *** [atlas_run] Error 44 make[2]: *** [IRunArchInfo_x86] Error 2 Clock rate configured as 2350Mhz ERROR: enum fam=3, chip=2, mach=0 make[3]: *** [atlas_run] Error 44 make[2]: *** [IRunArchInfo_x86] Error 2 Maximum number of threads configured as 4 Parallel make command configured as '$(MAKE) -j 4' ERROR: enum fam=3, chip=2, mach=0 make[3]: *** [atlas_run] Error 44 make[2]: *** [IRunArchInfo_x86] Error 2 Cannot detect CPU throttling. rm -f config1.out make atlas_run atldir=/home/allusers/Downloads/atlas3.10.1/build_vbubuntu exe=xprobe_comp redir=config1.out \ args="-v 0 -o atlconf.txt -O 1 -A 25 -Si nof77 0 -V 448 -b 64 -d b /home/allusers/Downloads/atlas3.10.1/build_vbubuntu" make[1]: Entering directory `/home/allusers/Downloads/atlas3.10.1/build_vbubuntu' cd /home/allusers/Downloads/atlas3.10.1/build_vbubuntu ; ./xprobe_comp -v 0 -o atlconf.txt -O 1 -A 25 -Si nof77 0 -V 448 -b 64 -d b /home/allusers/Downloads/atlas3.10.1/build_vbubuntu > config1.out make[2]: gfortran: Command not found make[2]: *** [IRunF77Comp] Error 127 make[2]: g77: Command not found make[2]: *** [IRunF77Comp] Error 127 make[2]: f77: Command not found make[2]: *** [IRunF77Comp] Error 127 Unable to find usable compiler for F77; abortingMake sure compilers are in your path, and specify good compilers to configure (see INSTALL.txt or 'configure --help' for details)make[1]: *** [atlas_run] Error 8 make[1]: Leaving directory `/home/allusers/Downloads/atlas3.10.1/build_vbubuntu' make: *** [IRun_comp] Error 2 ERROR 512 IN SYSCMND: 'make IRun_comp args="-v 0 -o atlconf.txt -O 1 -A 25 -Si nof77 0 -V 448 -b 64"' mkdir src bin tune interfaces mkdir: cannot create directory ‘src’: File exists mkdir: cannot create directory ‘bin’: File exists mkdir: cannot create directory ‘tune’: File exists mkdir: cannot create directory ‘interfaces’: File exists make: *** [make_subdirs] Error 1 make -f Make.top startup make[1]: Entering directory `/home/allusers/Downloads/atlas3.10.1/build_vbubuntu' Make.top:1: Make.inc: No such file or directory Make.top:325: warning: overriding commands for target `/AtlasTest' Make.top:76: warning: ignoring old commands for target `/AtlasTest' make[1]: *** No rule to make target `Make.inc'. Stop. make[1]: Leaving directory `/home/allusers/Downloads/atlas3.10.1/build_vbubuntu' make: *** [startup] Error 2 mv: cannot move ‘lapack-3.5.0’ to ‘../reference/lapack-3.5.0’: Directory not empty mv: cannot stat ‘lib/Makefile’: No such file or directory ../configure: 450: ../configure: cannot create lib/Makefile: Directory nonexistent ../configure: 451: ../configure: cannot create lib/Makefile: Directory nonexistent ../configure: 452: ../configure: cannot create lib/Makefile: Directory nonexistent ../configure: 453: ../configure: cannot create lib/Makefile: Directory nonexistent ../configure: 509: ../configure: cannot create lib/Makefile: Directory nonexistent DONE configure

  Read the article

• Free RAM disappears - Memory leak?

  - by Izzy

  On a fresh started system, free reports about 1.5G used RAM (8G RAM alltogether, Ubuntu 12.04 with lightdm and plasma desktop, one konsole window started). Having the apps running I use, it still consumes not more than 2G. However, having the system running for a couple of days, more and more of my free RAM disappears -- without showing up in the list of used apps: while smem --pie=name reports less than 20% used (and 80% being available), everything else says differently. free -m for example reports on about day 7: total used free shared buffers cached Mem: 7459 7013 446 0 178 997 -/+ buffers/cache: 5836 1623 Swap: 9536 296 9240 (so you can see, it's not the buffers or the cache). Today this finally ended with the system crashing completely: the windows manager being gone, apps "hanging in the air" (frameless) -- and a popup notifying me about "too many open files". Syslog reports: kernel: [856738.020829] VFS: file-max limit 752838 reached So I closed those applications I was able to close, and killed X using Ctrl-Alt-backspace. X tried to come up again after that with failsafeX, but was unable to do so as it could no longer detect its configuration. So I switched to a console using Ctrl-Alt-F2, captured all information I could think of (vmstat, free, smem, proc/meminfo, lsof, ps aux), and finally rebooted. X again came up with failsafeX; this time I told it to "recover from my backed-up configuration", then switched to a console and successfully used startx to bring up the graphical environment. I have no real clue to what is causing this issue -- though it must have to do either with X itself, or with some user processes running on X -- as after killing X, free -m output looked like this: total used free shared buffers cached Mem: 7459 2677 4781 0 62 419 -/+ buffers/cache: 2195 5263 Swap: 9536 59 9477 (~3.5GB being freed) -- to compare with the output after a fresh start: total used free shared buffers cached Mem: 7459 1483 5975 0 63 730 -/+ buffers/cache: 689 6769 Swap: 9536 0 9536 Two more helpful outputs are provided by memstat -u. Shortly before the crash: User Count Swap USS PSS RSS mail 1 0 200 207 616 whoopsie 1 764 740 817 2300 colord 1 3200 836 894 2156 root 62 70404 352996 382260 569920 izzy 80 177508 1465416 1519266 1851840 After having X killed: User Count Swap USS PSS RSS mail 1 0 184 188 356 izzy 1 1400 708 739 1080 whoopsie 1 848 668 826 1772 colord 1 3204 804 888 1728 root 62 54876 131708 149950 267860 And after a restart, back in X: User Count Swap USS PSS RSS mail 1 0 212 217 628 whoopsie 1 0 1536 1880 5096 colord 1 0 3740 4217 7936 root 54 0 148668 180911 345132 izzy 47 0 370928 437562 915056 Edit: Just added two graphs from my monitoring system. Interesting to see: everytime when there's a "jump" in memory consumption, CPU peaks as well. Just found this right now -- and it reminds me of another indicator pointing to X itself: Often when returning to my machine and unlocking the screen, I found something doing heavvy work on my CPU. Checking with top, it always turned out to be /usr/bin/X :0 -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswitch -background none. So after this long explanation, finally my questions: What could be the possible causes? How can I better identify involved processes/applications? What steps could be taken to avoid this behaviour -- short from rebooting the machine all X days? I was running 8.04 (Hardy) for about 5 years on my old machine, never having experienced the like (always more than 100 days uptime, before rebooting for e.g. kernel updates). This now is a complete new machine with a fresh install of 8.04. In case it matters, some specs: AMD A4-3400 APU with Radeon(tm) HD Graphics, using the open-source ati/radeon driver (so no fglrx installed), 8GB RAM, WDC WD1002FAEX-0 hdd (1TB), Asus F1A75-V Evo mainboard. Ubuntu 12.04 64-bit with KDE4/Plasma. Apps usually open more or less permanently include Evolution, Firefox, konsole (with Midnight Commander running inside, about 4 tabs), and LibreOffice -- plus occasionally Calibre, Gimp and Moneyplex (banking software I'm already using for almost 20 years now, in a version which did fine on Hardy).

  Read the article

• 5.1 surround sound on Acer Aspire 5738ZG with Ubuntu 11.10

  - by kbargais_LV

  I got a problem with sound. I tried everything but no results. :( I got 3 sound ports. my daemon: # This file is part of PulseAudio. # # PulseAudio is free software; you can redistribute it and/or modify # it under the terms of the GNU Lesser General Public License as published by # the Free Software Foundation; either version 2 of the License, or # (at your option) any later version. # # PulseAudio is distributed in the hope that it will be useful, but # WITHOUT ANY WARRANTY; without even the implied warranty of # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU # General Public License for more details. # # You should have received a copy of the GNU Lesser General Public License # along with PulseAudio; if not, write to the Free Software # Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 # USA. ## Configuration file for the PulseAudio daemon. See pulse-daemon.conf(5) for ## more information. Default values are commented out. Use either ; or # for ## commenting. ; daemonize = no ; fail = yes ; allow-module-loading = yes ; allow-exit = yes ; use-pid-file = yes ; system-instance = no ; local-server-type = user ; enable-shm = yes ; shm-size-bytes = 0 # setting this 0 will use the system-default, usually 64 MiB ; lock-memory = no ; cpu-limit = no ; high-priority = yes ; nice-level = -11 ; realtime-scheduling = yes ; realtime-priority = 5 ; exit-idle-time = 20 ; scache-idle-time = 20 ; dl-search-path = (depends on architecture) ; load-default-script-file = yes ; default-script-file = /etc/pulse/default.pa ; log-target = auto ; log-level = notice ; log-meta = no ; log-time = no ; log-backtrace = 0 resample-method = speex-float-1 ; enable-remixing = yes ; enable-lfe-remixing = no flat-volumes = no ; rlimit-fsize = -1 ; rlimit-data = -1 ; rlimit-stack = -1 ; rlimit-core = -1 ; rlimit-as = -1 ; rlimit-rss = -1 ; rlimit-nproc = -1 ; rlimit-nofile = 256 ; rlimit-memlock = -1 ; rlimit-locks = -1 ; rlimit-sigpending = -1 ; rlimit-msgqueue = -1 ; rlimit-nice = 31 ; rlimit-rtprio = 9 ; rlimit-rttime = 1000000 ; default-sample-format = s16le ; default-sample-rate = 44100 ; default-sample-channels = 6 ; default-channel-map = front-left,front-right default-fragments = 8 default-fragment-size-msec = 10 ; enable-deferred-volume = yes ; deferred-volume-safety-margin-usec = 8000 ; deferred-volume-extra-delay-usec = 0

  Read the article

• SOA Community Newsletter May 2014

  - by JuergenKress

  Registration for the Fusion Middleware Summer Camps 2014 is open – Register asap for one of our bootcamps August 4th – 8th 2014 in Lisbon. Please read details and pre-requisitions careful before you register. We expect that like in the past, the conference will be booked out soon! If you can’t make it to Lisbon attend our SOA Suite 11c free on-demand Bootcamp or  Managing the Complexity of IoT online trainings. With more than 5000 customers, SOA Suite Achieves Significant Customer Adoption and Industry Recognition.Thanks to all our SOA Specialized partners for making our joins SOA customers successful! As a summary of the Industrial SOA series we published the Podcast Show Notes: SOA and Cloud - Where's This Relationship Going? Make sure you use the Oracle Demo Systems for your customer presentations. The demo systems are hosted by Oracle and include complete scenarios based on the latest Middleware version like the new B2B SOA Suite Demo System! For local presentations without fast internet use the SOA/BPM 11.1.1.7.1 Virtual Machine and Case Management Sample. At our SOA Community Workspace (SOA Community membership required) you can get new IoT presentations for Location Based Offers for Banking & Whitepaper and online Webcast & Utility presentation. In this newsletter you will find many articles about OSB: OSB 11g – A Hands-on Tutorial & Using Split-Joins in OSB Services for parallel processing of messages & OSB, Service Callouts and OQL & Working with Oracle Security Token Service. Thanks for sharing all the additional SOA articles within the community: How to configure Oracle SOA/BPM task auto release & Controlling BPEL process flow at runtime & Upgrading to Oracle SOA Suite 11g PS6 (11.1.1.7)? Do this. & BPEL and BPM's performance monitoring using DMS & SOA 11g - Create RESTful Service In Oracle SOA & Wrong timezone causes TopLink warning in SOA suite. Highlight of the BPM and ACM section is the IDC BPM vendor report. The new bundle Patch including the ACM UI is now available. If you want to learn more about ACM, get the ACM training material at our SOA Community Workspace (SOA Community membership required). A great demo for your next BPM presentation is the BPM iPad app. It’s simpleMobile BPM is Not An Option. It’s a Necessity. Thanks for sharing all the additional BPM articles within the community: BPM update adds Case Management Web Interface and REST APIs & Implementing deadline functionality with Oracle Adaptive Case Management & BPM 11g Timeout Heuristics & Humantask Assignment: Names and Expressions Assignment via Rules. In our last section Architecture, it is all about design. Usability is a key factor for customer satisfaction, worth to spend some time and read the Simplified User Experience Design Patterns eBook. Great blueprint for your project! See you in Lisbon! To read the newsletter please visit www.tinyurl.com/soaNewsMay2014 (OPN Account required) To become a member of the SOA Partner Community please register at http://www.oracle.com/goto/emea/soa (OPN account required) If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Facebook Wiki Mix Forum Technorati Tags: newsletter,SOA Community newsletter,SOA Community,Oracle,OPN,Jürgen Kress

  Read the article

• Strange Happenings

  - by MOSSLover

  There are weeks we go about our life thinking nothing is going to change nothing will happen.  Then there are other weeks a billion things happen at once.  Friday started off very weird for me.  I flew into Atlanta and I met some cool people for another SharePoint event.  I had some good conversations.  Saturday then hit me and my virtual machine bombed in my presentation after the auto updater ran.  I was writing code on the board and describing everything in notepad.  I would say as presentations go it was the best and the worst presentation all wrapped into one.  The next day I was in Baltimore and I hung out with my aunt which was relatively uneventful and great.  Then Monday hit and half my presentations failed or succeeded and my screen freezes so I start describing the code.  I was on top of my game until Monday night.  On top of the world.  I'm exhausted I get into Raleigh and one of the craziest stories of my life happens.  So my boss has been renting cars through Priceline this week I got a different company than the other weeks. The company gives me a Ford Focus and I plug in the coordinates on my IPhone where I want go.  I head out and then I get to the destination hotel (or I thought I did). I go inside it's the wrong hotel the other one is a few miles away.  I walk outside hop into the car and it sounds like a gunshot.  Nothing is starting...Am I doing something wrong?  No I'm not the car is completely dead in the water.  I call the rental car facility and they tell me to call roadside they are closing for the night.  Roadside says they can't give me a new car but they can get me a jump then I have to take it up with the facility.  They send me a tow truck to give me a jump the guy can't jump the car.  He tells me this vehicle was towed about an hour ago.  He shows me a copy of a slip from when he towed it.  We also notice the rental car company left one of there price scanning guns in the vehicle.  I call up roadside and now they are interested in getting me a car because I need to be onsite tomorrow.  They get the manager of the facility on the phone he apologizes profusely and he says he'll be there in 10 minutes.  About 30 minutes pass and him plus another dude show up with a Ford Escape leather interior.  At this point I hand him the gun tell him someone left it in the vehicle and that I'm not so happy with them.  I ask them to comp my rental they can't due to Priceline, however if I call him again this week he can get me a voucher.  It's about 2 am and I'm ready to get to the hotel I don't make it in the next morning until 10 am.  I would say this was a crazy week all forms of technology are trying to tell me something.  What I have no idea, but we'll see the outcome soon.  I feel so weird tons of change is about to happen.  I don't know if it's good or bad.  I think this week is some form of omen.

  Read the article

• Launching Ops Center 12c

  - by user12601629

  Oracle Enterprise Manager Ops Center 12c is most ambitious version of the Ops Center tooling that we've ever released. I think that make it appropriate that we launched it in grand style! When it became clear we were going to be complete with the 12c final release about this time of year, the marketing team proposed that we roll the launch of 12c into Oracle OpenWorld Tokyo.  I thought that sounded like a fine idea!  You see, I have always loved Japan.  I even studied a bit of Japanese language back in school. OpenWorld Tokyo was an outstanding even this year.  It was held in Roppongi, one of the most stylish districts in Tokyo. And, to make things even better, the Sakura (cherry blossoms) were blooming.  If you've never been in Japan for cherry blossom season, it's a must see!  Here are a couple of pics for you. Here is a picture from Roppongi, near the conference.  Here's a picture near the Imperial Palace.  A couple of friends from the local sales team took me here before my flight out. So, now back to the product launch! We choose to launch the product in John Fowler's "Engineered Systems" keynote address.  It made perfect sense because of the close ties of Ops Center to the Systems portfolio of products.  It was a packed house for the keynote.  Here's a picture I took just before we started -- there were also hundreds more people in "overflow" rooms in other parts of the venue. Here's a picture of me on stage during the launch. While there are countless new features in Ops Center 12c that customers will love, I had to limit myself to discussing just three. Mission Critical Clouds Solaris 11 Engineered Systems So, what does Mission Critical Cloud mean?  It means we've expanded EM's cloud capabilities in a couple of key areas. First, we've expanded the "self service provisioning" capabilities we have to include SPARC -- not just x86.  Now you can build clouds of Solaris Zones with ease!  Second, we've much more deeply integrated high-end storage and network management into the cloud layers.  These may our IaaS story is now much more powerful! For Solaris 11, we didn't simply port our monitoring agent to S11.  That would have been easy, but also boring! We support S11 deeply.  Full access to the power of the IPS packaging system, the new virtualized networking stack, new Zones features, the Auto Install framework.  If you're ready to try Solaris 11 then Ops Center is ready for you. Last is on the area of Engineered Systems.  These combinations of hardware and software are fast and powerful. However, we're also on a mission to make them ever easier to manage.  We've made major strides with Ops Center 12c. Manage these systems as racks, not individual components.  The new capabilities for the new engineered systems like Exalogic and SPARC SuperCluster and striking. You can read more here: Oracle Unveils Oracle Enterprise Manager Ops Center 12c So, I'll wrap this up with one final bit of fun. One of my friends from the Oracle marketing department found a super cool place to get dinner.  It's a restaurant called Gonpachi. It turns out this is the place that inspired the scene in the Quentin Taratino movie Kill Bill where Uma Thurman fights 88 Ninjas.  Here is a picture I snapped while we were there. It was surely a good time. Check it out next time you're in Tokyo.

  Read the article

• Slow Ubuntu 10.04 after long time unused

  - by Winston Ewert

  I'm at spring break so I'm back at my parent's house. I've turned my computer on which has been off since January and its unusably slow. This was not the case when I last used the computer in January. It is running 10.04, Memory: 875.5 MB CPU: AMD Athlon 64 X2 Dual Core Processor 4400+ Available Disk Space: 330.8 GB I'm not seeing a large usage of either memory or Disk I/O. If I look at my list of processes there is only a very small amount of CPU usage. However, if I hover over the CPU usage graph that I've on the top bar, I sometimes get really high readings like 100%. It took a long time to boot, to open firefox, to open a link in firefox. As far as I can tell everything that the computer tries to do is just massively slow. Right now, I'm apt-get dist-upgrading to install any updates that I will have missed since last time this computer was on. Any ideas as to what is going on here? UPDATE: I thought to check dmesg and it has a lot of entries like this: [ 1870.142201] ata3.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x0 [ 1870.142206] ata3.00: irq_stat 0x40000008 [ 1870.142210] ata3.00: failed command: READ FPDMA QUEUED [ 1870.142217] ata3.00: cmd 60/08:10:c0:4a:65/00:00:03:00:00/40 tag 2 ncq 4096 in [ 1870.142218] res 41/40:00:c5:4a:65/00:00:03:00:00/40 Emask 0x409 (media error) <F> [ 1870.142221] ata3.00: status: { DRDY ERR } [ 1870.142223] ata3.00: error: { UNC } [ 1870.143981] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1870.146758] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1870.146761] ata3.00: configured for UDMA/133 [ 1870.146777] ata3: EH complete [ 1872.092269] ata3.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x0 [ 1872.092274] ata3.00: irq_stat 0x40000008 [ 1872.092278] ata3.00: failed command: READ FPDMA QUEUED [ 1872.092285] ata3.00: cmd 60/08:00:c0:4a:65/00:00:03:00:00/40 tag 0 ncq 4096 in [ 1872.092287] res 41/40:00:c5:4a:65/00:00:03:00:00/40 Emask 0x409 (media error) <F> [ 1872.092289] ata3.00: status: { DRDY ERR } [ 1872.092292] ata3.00: error: { UNC } [ 1872.094050] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1872.096795] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1872.096798] ata3.00: configured for UDMA/133 [ 1872.096814] ata3: EH complete [ 1874.042279] ata3.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x0 [ 1874.042285] ata3.00: irq_stat 0x40000008 [ 1874.042289] ata3.00: failed command: READ FPDMA QUEUED [ 1874.042296] ata3.00: cmd 60/08:10:c0:4a:65/00:00:03:00:00/40 tag 2 ncq 4096 in [ 1874.042297] res 41/40:00:c5:4a:65/00:00:03:00:00/40 Emask 0x409 (media error) <F> [ 1874.042300] ata3.00: status: { DRDY ERR } [ 1874.042302] ata3.00: error: { UNC } [ 1874.044048] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1874.046837] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1874.046840] ata3.00: configured for UDMA/133 [ 1874.046861] sd 2:0:0:0: [sda] Unhandled sense code [ 1874.046863] sd 2:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 1874.046867] sd 2:0:0:0: [sda] Sense Key : Medium Error [current] [descriptor] [ 1874.046872] Descriptor sense data with sense descriptors (in hex): [ 1874.046874] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 1874.046883] 03 65 4a c5 [ 1874.046886] sd 2:0:0:0: [sda] Add. Sense: Unrecovered read error - auto reallocate failed [ 1874.046892] sd 2:0:0:0: [sda] CDB: Read(10): 28 00 03 65 4a c0 00 00 08 00 [ 1874.046900] end_request: I/O error, dev sda, sector 56969925 [ 1874.046920] ata3: EH complete I'm not certain, but that looks like my problem may be a failing hard drive. But the drive is less then a year old, it really shouldn't be failing now...

  Read the article

• Enable grub boot menu on new system

  - by Remus Rigo

  I have installed Ubuntu 11.04 and I would like to see the boot menu when the system starts (by default it is hidden or the timeout=0) # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 44f311b4-0b40-4d10-b004-78108539fc39 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 44f311b4-0b40-4d10-b004-78108539fc39 set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 44f311b4-0b40-4d10-b004-78108539fc39 insmod jpeg if background_image /boot/grub/boot.jpg; then true else set menu_color_normal=white/black set menu_color_highlight=black/light-gray fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 2.6.38-8-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 44f311b4-0b40-4d10-b004-78108539fc39 linux /boot/vmlinuz-2.6.38-8-generic root=UUID=44f311b4-0b40-4d10-b004-78108539fc39 ro quiet splash vt.handoff=7 initrd /boot/initrd.img-2.6.38-8-generic } menuentry 'Ubuntu, with Linux 2.6.38-8-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 44f311b4-0b40-4d10-b004-78108539fc39 echo 'Loading Linux 2.6.38-8-generic ...' linux /boot/vmlinuz-2.6.38-8-generic root=UUID=44f311b4-0b40-4d10-b004-78108539fc39 ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.38-8-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 44f311b4-0b40-4d10-b004-78108539fc39 linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 44f311b4-0b40-4d10-b004-78108539fc39 linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ "x${timeout}" != "x-1" ]; then if keystatus; then if keystatus --shift; then set timeout=-1 else set timeout=0 fi else if sleep --interruptible 3 ; then set timeout=0 fi fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ###

  Read the article

• NetworkManager Applet shows no networks

  - by Kkelk

  I am "the friend" referred to in the questions here and here. I decided to come and ask a question myself, as I can still not connect to the wireless network. I downloaded Keryx, as suggested here, and managed to download the necessary package and its dependencies. When I attempted to install the packages on Ubuntu using Keryx, Keryx just closed. Following this, I installed the packages manually using dpkg, and as far as I can tell, this was successful: kieran@ubuntu:~$ cd /host/wifi/Keryx/keryx/projects/Kieran/packages kieran@ubuntu:/host/wifi/Keryx/keryx/projects/Kieran/packages$ sudo dpkg -i *.deb [sudo] password for kieran: Selecting previously deselected package bcmwl-kernel-source. (Reading database ... 118296 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.60.48.36+bdcom-0ubuntu5_i386.deb) ... Selecting previously deselected package dkms. Unpacking dkms (from dkms_2.1.1.2-3ubuntu1.1_all.deb) ... Selecting previously deselected package fakeroot. Unpacking fakeroot (from fakeroot_1.14.4-1ubuntu1_i386.deb) ... Selecting previously deselected package linux-image. Unpacking linux-image (from linux-image_2.6.35.22.23_i386.deb) ... Selecting previously deselected package menu. Unpacking menu (from menu_2.1.44ubuntu1_i386.deb) ... Selecting previously deselected package patch. Unpacking patch (from patch_2.6-2ubuntu1_i386.deb) ... Setting up fakeroot (1.14.4-1ubuntu1) ... update-alternatives: using /usr/bin/fakeroot-sysv to provide /usr/bin/fakeroot (fakeroot) in auto mode. Setting up linux-image (2.6.35.22.23) ... Setting up menu (2.1.44ubuntu1) ... Setting up patch (2.6-2ubuntu1) ... Processing triggers for man-db ... Setting up dkms (2.1.1.2-3ubuntu1.1) ... Setting up bcmwl-kernel-source (5.60.48.36+bdcom-0ubuntu5) ... Loading new bcmwl-5.60.48.36+bdcom DKMS files... First Installation: checking all kernels... Building only for 2.6.35-22-generic Building for architecture i686 Building initial module for 2.6.35-22-generic Done. wl.ko: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/2.6.35-22-generic/updates/dkms/ depmod..... DKMS: install Completed. update-initramfs: deferring update (trigger activated) Processing triggers for install-info ... Processing triggers for doc-base ... Processing 31 changed 1 added doc-base file(s)... Registering documents with scrollkeeper... Processing triggers for menu ... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-2.6.35-22-generic Warning: No support for locale: en_GB.utf8 After rebooting, however, there were still no wireless networks in the NetworkManager Applet list. I opened the file /var/lib/NetworkManager/NetworkManager.state, and both NetworkEnabled and WirelessEnabled were set to True. While i'm very concious I may be asking a stupid question here, both my friend and I have nothing left to suggest, and as such - I would be very grateful for any answers as to how to get wireless working.

  Read the article

• Very slow KVM in Ubuntu 12.04

  - by Guy Fawkes

  I use Ubuntu 12.04 64-bit and KVM, my CPU is Core i5 3.3 GHz and I have 8 GB of DDR3 RAM. I run Windows 7 in KVM and it's extremely slow. My co-worker use Debian on the same PC configuration and can run Windows 7 extremely fast! Where can be my problem? sudo cat /etc/libvirt/qemu/windows.xml <!-- WARNING: THIS IS AN AUTO-GENERATED FILE. CHANGES TO IT ARE LIKELY TO BE OVERWRITTEN AND LOST. Changes to this xml configuration should be made using: virsh edit windows or other application using the libvirt API. --> <domain type='kvm'> <name>windows</name> <uuid>5c685175-baea-0ca6-591f-8269d923ffb8</uuid> <memory>2097152</memory> <currentMemory>2097152</currentMemory> <vcpu>1</vcpu> <os> <type arch='x86_64' machine='pc-1.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='localtime'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/windows.img'/> <target dev='hda' bus='ide'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <controller type='ide' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='network'> <mac address='52:54:00:94:63:91'/> <source network='default'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <input type='tablet' bus='usb'/> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes'/> <sound model='ich6'> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </sound> <video> <model type='vga' vram='262144' heads='1'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> </domain>

  Read the article

• Why I Love the Social Management Platform I Use

  - by Mike Stiles

  Not long ago, I asked the product heads for the various components of the Oracle Social Cloud’s SRM to say what they thought was coolest about their component. And while they did a fine job, it was recently pointed out to me that no one around here uses the platform in a real-world setting more than I do, as I not only blog and podcast my brains out, I also run Oracle Social’s own social properties. Of course I’m pro-Oracle Social’s product. Duh. But if you can get around immediately writing this off as a puff piece, there are real reasons beyond my employment that the Oracle SRM works for me as a community manager. If it didn’t, I could have simply written about something else, like how people love smartphones or something genius like that. Post Grid I like seeing what I want to see. I’m difficult that way. Post grid lets me see all posts for all channels, with custom columns showing me how posts are doing. I can filter the grid by social channel, published, scheduled, draft, suggested, etc. Then there’s a pullout side panel that shows me post details, including engagement analytics. From the pullout, I can preview the post, do a quick edit, a full edit, or (my favorite) copy a post so I can edit it and schedule it for other times so I don’t have to repeat from scratch. I’m not lazy, just time conscious. The Post Creation Environment Given our post volume, I need this to be as easy as it can be. I can highlight which streams I want the post to go out on, edit for the individual streams, maintain a media library that’s easy to upload to and attach from, tag posts, insert links that auto-shorten to an orac.le shortlink, schedule with a nice calendar visual, geo-target, drop photos inline into Twitter, and review each post. Watching My Channels The Engage component of the Oracle SRM brings in and drops into a grid the activity that’s happening on all my channels. I keep this open round-the-clock. Again, I get to see only what I want; social network, stream, unread messages, engagement by how I labeled them, and date range. I can bring up a post with a click, reply, label it, retweet it, assign it, delete it, archive it, etc. So don’t bother trying to be a troll on my channels. Analytics Social publishing and engaging 24/7 would be pretty unrewarding if I couldn’t see how our audience was responding. Frankly, I get more analytics than I know what to do with (I’m a content creator, not a data analyst). But I do know what numbers I care about, and they’re available by channel, date range, and campaigns. I’m seeing fan count, sources and demographics. I’m seeing engagement, what kinds of posts are getting engagement, and top engagers. I’m seeing my reach, both organic and paid. I’m seeing how individual posts performed in terms of engagement and virality, and posting time/date insight. Have I covered all the value propositions? I’ve covered pathetically few of them. It would be impossible in blog length to give shout-outs to the vast number of features and functionalities. From organizing teams and managing permissions with Workflow to the powerful ability to monitor topics (and your competition) across the web in Listen, it’s a major, and increasingly necessary, weapon in your social marketing arsenal. The life of a Community Manager is not for everybody. So if the Oracle SRM can actually make a Community Manager’s life easier, what’s not to love? I invite you to take a look at and participate in our Oracle Social Cloud social channels! Facebook Twitter YouTube Google Plus LinkedIn Daily Podcast on iHeartRadio @mikestiles @oraclesocial Photo: freeimages.com

  Read the article

• links for 2010-12-23

  - by Bob Rhubart

  Oracle VM Virtualbox 4.0 extension packs (Wim Coekaerts Blog) Wim Coekaerts describes the the new extension pack in Oracle VM Virtualbox 4.0 and how it's different from 3.2 and earlier releases. (tags: oracle otn virtualization virtualbox) Oracle Fusion Middleware Security: Creating OES SM instances on 64 bit systems "I've already opened a bug on this against OES 10gR3 CP5, but in case anyone else runs into it before it gets fixed I wanted to blog it too. (NOTE: CP5 is when official support was introduced for running OES on a 64 bit system with a 64 bit JVM)" - Chris Johnson (tags: oracle otn fusionmiddleware security) Oracle Enterprise Manager Grid Control: Shared loader directory, RAC and WebLogic Clustering "RAC is optional. Even the load balancer is optional. The feed from the agents also goes to the load balancer on a different port and it is routed to the available management server. In normal case, this is ok." - Porus Homi Havewala (tags: WebLogic oracle otn grid clustering) Magic Web Doctor: Thought Process on Upgrading WebLogic Server to 11g "Upgrading to new versions can be challenging task, but it's done for linear scalability, continuous enhanced availability, efficient manageability and automatic/dynamic infrastructure provisioning at a low cost." - Chintan Patel (tags: oracle otn weblogic upgrading) InfoQ: Using a Service Bus to Connect the Supply Chain Peter Paul van de Beek presents a case study of using a service bus in a supply channel connecting a wholesale supplier with hundreds of retailers, the overall context and challenges faced – including the integration of POS software coming from different software providers-, the solution chosen and its implementation, how it worked out and the lessons learned along the way. (tags: ping.fm) Oracle VM VirtualBox 4.0 is released! - The Fat Bloke Sings The Fat Bloke spreads the news and shares some screenshots.  (tags: oracle otn virtualization virtualbox) Leaks on Wikis: "Corporations...You're Next!" Oracle Desktop Virtualization Can Help. (Oracle's Virtualization Blog) "So what can you do to guard against these types of breaches where there is no outsider (or even insider) intrusion to detect per se, but rather someone with malicious intent is physically walking out the door with data that they are otherwise allowed to access in their daily work?" - Adam Hawley (tags: oracle otn virtualization security) OTN ArchBeat Podcast Guest Roster As the OTN ArchBeat Podcast enters its third year, it's time to acknowledge the invaluable contributions of the guests who have participated in ArchBeat programs. Check out this who's who of ArchBeat podcast panelists, with links to their respective interviews and more. (tags: oracle otn oracleace podcast archbeat) Show Notes: Architects in the Cloud (ArchBeat) Now available! Part 2 (of 4) of the ArchBeat interview with Stephen G. Bennett and Archie Reed, the authors of "Silver Clouds, Dark Linings: A Concise Guide to Cloud Computing." (tags: oracle otn podcast cloud) A Cautionary Tale About Multi-Source JNDI Configuration (Scott Nelson's Portal Productivity Ponderings) "I ran into this issue after reading that p13nDataSource and cgDataSource-NonXA should not be configured as multi-source. There were some issues changing them to use the basic JDBC connection string and when rolling back to the bad configuration the server went 'Boom.'" - Scott Nelson (tags: weblogic jdbc oracle jndi)

  Read the article

• Why Is Hibernation Still Used?

  - by Jason Fitzpatrick

  With the increased prevalence of fast solid-state hard drives, why do we still have system hibernation? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-driven grouping of Q&A web sites. The Question SuperUser reader Moses wants to know why he should use hibernate on a desktop machine: I’ve never quite understood the original purpose of the Hibernation power state in Windows. I understand how it works, what processes take place, and what happens when you boot back up from Hibernate, but I’ve never truly understood why it’s used. With today’s technology, most notably with SSDs, RAM and CPUs becoming faster and faster, a cold boot on a clean/efficient Windows installation can be pretty fast (for some people, mere seconds from pushing the power button). Standby is even faster, sometimes instantaneous. Even SATA drives from 5-6 years ago can accomplish these fast boot times. Hibernation seems pointless to me [on desktop computers] when modern technology is considered, but perhaps there are applications that I’m not considering. What was the original purpose behind hibernation, and why do people still use it? Quite a few people use hibernate, so what is Moses missing in the big picture? The Answer SuperUser contributor Vignesh4304 writes: Normally hibernate mode saves your computer’s memory, this includes for example open documents and running applications, to your hard disk and shuts down the computer, it uses zero power. Once the computer is powered back on, it will resume everything where you left off. You can use this mode if you won’t be using the laptop/desktop for an extended period of time, and you don’t want to close your documents. Simple Usage And Purpose: Save electric power and resuming of documents. In simple terms this comment serves nice e.g (i.e. you will sleep but your memories are still present). Why it’s used: Let me describe one sample scenario. Imagine your battery is low on power in your laptop, and you are working on important projects on your machine. You can switch to hibernate mode – it will result your documents being saved, and when you power on, the actual state of application gets restored. Its main usage is like an emergency shutdown with an auto-resume of your documents. MagicAndre1981 highlights the reason we use hibernate everyday: Because it saves the status of all running programs. I leave all my programs open and can resume working the next day very easily. Doing a real boot would require to start all programs again, load all the same files into those programs, get to the same place that I was at before, and put all my windows in exactly the same place. Hibernating saves a lot of work pulling these things back up again. It’s not unusual to find computers around the office here that have been hibernated day in and day out for months without an actual full system shutdown and restart. It’s enormously convenient to freeze your work space at the exact moment you stopped working and to turn right around and resume there the next morning. Have something to add to the explanation? Sound off in the the comments. Want to read more answers from other tech-savvy Stack Exchange users? Check out the full discussion thread here.     

  Read the article

• Design pattern for logging changes in parent/child objects saved to database

  - by andrew

  I’ve got a 2 database tables in parent/child relationship as one-many. I’ve got three classes representing the data in these two tables: Parent Class { Public int ID {get; set;} .. other properties } Child Class { Public int ID {get;set;} Public int ParentID {get; set;} .. other properties } TogetherClass { Public Parent Parent; Public List<Child> ChildList; } Lastly I’ve got a client and server application – I’m in control of both ends so can make changes to both programs as I need to. Client makes a request for ParentID and receives a Together Class for the matching parent, and all of the child records. The client app may make changes to the children – add new children, remove or modify existing ones. Client app then sends the Together Class back to the server app. Server app needs to update the parent and child records in the database. In addition I would like to be able to log the changes – I’m doing this by having 2 separate tables one for Parent, one for child; each containing the same columns as the original plus date time modified, by whom and a list of the changes. I’m unsure as to the best approach to detect the changes in records – new records, records to be deleted, records with no fields changed, records with some fields changed. I figure I need to read the parent & children records and compare those to the ones in the Together Class. Strategy A: If Together class’s child record has an ID of say 0, that indicates a new record; insert. Any deleted child records are no longer in the Together Class; see if any of the comparison child records are not found in the Together class and delete if not found (Compare using ID). Check each child record for changes and if changed log. Strategy B: Make a new Updated TogetherClass UpdatedClass { Public Parent Parent {get; set} Public List<Child> ListNewChild {get;set;} Public List<Child> DeletedChild {get;set;} Public List<Child> ExistingChild {get;set;} // used for no changes and modified rows } And then process as per the list. The reason why I’m asking for ideas is that both of these solutions don’t seem optimal to me and I suspect this problem has been solved already – some kind of design pattern ? I am aware of one potential problem in this general approach – that where Client App A requests a record; App B requests same record; A then saves changes; B then saves changes which may overwrite changes A made. This is a separate locking issue which I’ll raise a separate question for if I’ve got trouble implementing. The actual implementation is c#, SQL Server and WCF between client and server - sharing a library containing the class implementations. Apologies if this is a duplicate post – I tried searching various terms without finding a match though.

  Read the article

• Managing Operational Risk of Financial Services Processes – part 1/ 2

  - by Sanjeevio

  Financial institutions view compliance as a regulatory burden that incurs a high initial capital outlay and recurring costs. By its very nature regulation takes a prescriptive, common-for-all, approach to managing financial and non-financial risk. Needless to say, no longer does mere compliance with regulation will lead to sustainable differentiation.  Genuine competitive advantage will stem from being able to cope with innovation demands of the present economic environment while meeting compliance goals with regulatory mandates in a faster and cost-efficient manner. Let’s first take a look at the key factors that are limiting the pursuit of the above goal. Regulatory requirements are growing, driven in-part by revisions to existing mandates in line with cross-border, pan-geographic, nature of financial value chains today and more so by frequent systemic failures that have destabilized the financial markets and the global economy over the last decade.  In addition to the increase in regulation, financial institutions are faced with pressures of regulatory overlap and regulatory conflict. Regulatory overlap arises primarily from two things: firstly, due to the blurring of boundaries between lines-of-businesses with complex organizational structures and secondly, due to varying requirements of jurisdictional directives across geographic boundaries e.g. a securities firm with operations in US and EU would be subject different requirements of “Know-Your-Customer” (KYC) as per the PATRIOT ACT in US and MiFiD in EU. Another consequence and concomitance of regulatory change is regulatory conflict, which again, arises primarily from two things: firstly, due to diametrically opposite priorities of line-of-business and secondly, due to tension that regulatory requirements create between shareholders interests of tighter due-diligence and customer concerns of privacy. For instance, Customer Due Diligence (CDD) as per KYC requires eliciting detailed information from customers to prevent illegal activities such as money-laundering, terrorist financing or identity theft. While new customers are still more likely to comply with such stringent background checks at time of account opening, existing customers baulk at such practices as a breach of trust and privacy. As mentioned earlier regulatory compliance addresses both financial and non-financial risks. Operational risk is a non-financial risk that stems from business execution and spans people, processes, systems and information. Operational risk arising from financial processes in particular transcends other sources of such risk. Let’s look at the factors underpinning the operational risk of financial processes. The rapid pace of innovation and geographic expansion of financial institutions has resulted in proliferation and ad-hoc evolution of back-office, mid-office and front-office processes. This has had two serious implications on increasing the operational risk of financial processes: ·         Inconsistency of processes across lines-of-business, customer channels and product/service offerings. This makes it harder for the risk function to enforce a standardized risk methodology and in turn breaches harder to detect. ·         The proliferation of processes coupled with increasingly frequent change-cycles has resulted in accidental breaches and increased vulnerability to regulatory inadequacies. In summary, regulatory growth (including overlap and conflict) coupled with process proliferation and inconsistency is driving process compliance complexity In my next post I will address the implications of this process complexity on financial institutions and outline the role of BPM in lowering specific aspects of operational risk of financial processes.

  Read the article

< Previous Page | 333 334 335 336 337 338 339 340 341 342 343 344  | Next Page >