Search Results

Search found 13347 results on 534 pages for 'embedded device'.

Page 367/534 | < Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >

  • Ubuntu server very slow out of the blue sky (Rails, passenger, nginx)

    - by snitko
    I run Ubuntu server 8.04 on Linode with multiple Rails apps under Passenger + nginx. Today I've noticed it takes quite a lot of time to load a page (5-10 secs). And it's not only websites, ssh seems to be affected too. Having no clue why this may be happening, I started to check different things. I checked how the log files are rotated, I checked if there's enough free disk space and memory. I also checked IO rate, here's the output: $ iostat avg-cpu: %user %nice %system %iowait %steal %idle 0.17 0.00 0.02 0.57 0.16 99.07 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvda 2.25 39.50 16.08 147042 59856 xvdb 0.00 0.05 0.00 192 0 xvdc 2.20 25.93 24.93 96530 92808 xvdd 0.01 0.12 0.00 434 16 xvde 0.04 0.23 0.35 858 1304 xvdf 0.37 0.31 4.12 1162 15352 Rebooting didn't help either. Any ideas where should I be looking?

    Read the article

  • How to use iptables to foward outbound web traffic to a proxy?

    - by jnman
    I've been hitting my head for a while as to how to do this. The scenario is as follows: I want to be able to forward all outbound web traffic from a browswer to Tor so that it is properly anonymized. Normally, one could just set the http proxy in the browser and be done with it but this is with a browser without the ability to do so specifically, a mobile browser. So ideally, what could be done then is to intercept all web/dns traffic requests from the browser and send it to Tor. Assume for this, that Tor will be running on the device too.

    Read the article

  • How to load tun module in linux?

    - by rabipelais
    I cannot manage to load the tun module in my archlinux box. I'm trying to connect with openvpn, but the log says nm-openvpn[6662]: Note: Cannot open TUN/TAP dev /dev/net/tun: No such device (errno=19) lsmod | grep tun returns nothing. If I run sudo modprobe tun it returns failure, but no error message, and lsmod still has no tun. The module seems to exist, as there is a tun.ko.gz in /lib/modules/....... I really dont know what else to try. Thanks in advance

    Read the article

  • iTunes sees my iPhone, but Windows 7 x64 doesn't

    - by Herb Caudill
    After reinstalling Windows 7 (64-bit), it has stopped recognizing my iPhone. I can see it in iTunes but not in Windows Explorer, so I can't get the photos off. I'm having this problem on three different machines and two different iPhones (my wife's and mine). It's maddening. I've had every version of iPhone since it first came out and I've never had this problem before. I've uninstalled and reinstalled iTunes (currently at 10.2.1.1). I've updated iOS on the phone (currently at 4.3). In the device manager, this is what I see: Here's the properties screen for the unrecognized iPhone: And here's what I get after going through the "update driver" process: Any ideas? At the end of my rope here...

    Read the article

  • Outlook.com custom domain, Exchange ActiveSync too many connected devices

    - by Mike C.
    I just setup Outlook.com to run on a custom domain. The web interface works well but when I connect it to Outlook 2013 I get the following error: There are too many devices syncing with this account. To sync using Outlook, try removing another device that is connected with this account such as a phone or another computer. File: outlook\pstprx\storeas\utils\airsyncstatuscodes.h Line: 88 HTTP/1.1 200 OK FolderStatus: 177 To re-try press F9... Error Code: 0x80004005 I've done my home work, using Google, and found that it is often due to having 3 or 4 devices connected to an account with 50+ folders. My account is empty, no email or folder, and is not synced with any devices, I confirmed that on http://devices.live.com. I'm out of option, any help would be greatly appreciated! Thank you

    Read the article

  • Windows 8 will not load color profiles - why?

    - by Fusilli Jerry
    I have a Spyder3Express color calibration device. Under Windows 7 the utility that came with it would happily load the custom profile I created with it without any hassles. Under Windows 8 (have just upgraded) there is no visible color shift when it says it has loaded the profile. I have gone into the Windows color management settings and when I select any profile and hit 'Set as Default' nothing happens. They all look the same. So Windows doesn't throw an error, but none of the profiles cause any color shifts at all. I have tried a large number of things, such as changing the global color settings for all user accounts and installing other color management software to see if it will load the profiles. The only way I can get a color shift is if I create a profile using Windows built in utility. Profiles created this way change the appearance of the screen, but any downloaded or created profiles make no difference. I am out of ideas. Please help :)

    Read the article

  • Cannot Enter Credentials Over UAC Prompts During Remote Assistance

    - by user100731
    We are using sonicwall firewall device through out our network and we use the sonicwall virtual assistance tool for remote desktop assistance. Since our systems are not in workgroup and are on domain we face problem when the UAC prompts appear. As a work around we edited the UAC policies, such as switching to secure desktop-disable, Allowing UI Acess applications to prompt for elevation without using secure desktop-Enable etc. The ultimate result was we are able to see the UAC prompt on the remote user system but not able to interact with it like we are not able to enter credentials to it even I can see the password being entered if it is done by the local user. However, we cannot interact with UAC prompt window remotely. Is there any solution for this?

    Read the article

  • NetFlow Storage Calculator

    - by javano
    I am planning to deploy a NetFlow server (using NfSen/NfDump) for harvesting data from Cisco devices; Are there standard calculations or guidelines I can use to calculate my server requirements, specifically I need to plan for storage. Is there a way of knowing how much data I will collect per day for example, given N flows? Lets say one device has 10k flows per day, this is typically XYZ MBs, so I can scale this up? If not, how many flows are you guys and girls recording per day, and how much data is this generating? Hopefully we can generate an estimate from everyone else's figures! P.S. If it makes a difference, I'll be collecting from <= 50 devices max (non more than 50Mbps each).

    Read the article

  • Fortigate 200A firewall CPU high resource usage

    - by user119720
    This morning I'm receiving complaints from several end users that saying their whole department network are slow and have intermittent. Therefore I've checked our firewall to see whether if something goes wrong with the device.From my observation in the FortiGate dashboard status, the CPU resources is very high (99 percent). My first assumption is to clear the log since in the alert log the Fortigate log mention that it is already 90% full.Based on my understanding,the log can be cleared by restarting the firewall. After restarting the firewall the network seems okay again but then after several minutes it went up again.The condition still persist until now. Can someone show me where else I can check to fix this issue? I've really appreciate any help that I can get here.Thanks. Edit: diag sys top command

    Read the article

  • "custom" routers for VPN - useful or waste of money?

    - by Andrew Heath
    I use VPN in China and my current service contract expires soon so I was checking what sort of plans are out there now. I found that Witopia offers a "Cloak Box", what appears to be a Linksys wireless router with allegedly hacked/custom firmware to support VPN. Aside from allowing multiple computers to share one VPN connection, is there anything else at work here to justify that price when most new routers are $100 or less these days? Or is this something targeted towards the cd-rom cupholder crowd? And yes, I've contacted them, but haven't heard back yet... EDIT I've heard back from the company - here are the details if anyone else is interested: the router is a Linksys WRT54GL running TomatoVPN custom firmware the hardware waranty is one (1) year, from Linksys/Cisco the VPN is hard-set, so any device connected to the router MUST use the VPN (Witopia blocks torrents) I've decided it's not for me, but hopefully this information will prove useful to others.

    Read the article

  • How do I keep second monitor (HDTV) from auto-disabling in XP when it is turned off?

    - by ThantiK
    I have a new 32" TV that I hooked up to the HDMI port on the back of my video card to use as a second monitor. I used an HDMI/DVI cable to hook it to the TV, and whenever I turn my TV off, XP disables the device tied to the TV so each time I want to use the TV as the monitor, I have to go into my display properties and enable it; it gets pretty annoying. How do I turn this 'feature' off? -- I have an NVidia card should it be specific to the nvidia control panel.

    Read the article

  • Canot send SMS using gammu-smsd

    - by khalid hussain
    I am trying to send SMS using gammu-smsd, but it does not work. Modem: Huawei E1550 Steps: #vi /etc/gammu-smsdrc port= /dev/ttyUSB0 connection = at Then restarted gammu-smsd: # /etc/init.d/gammu-smsd restart SMS Sending test echo "Test message" | gammu-smsd-inject TEXT 335123456 It does not send SMS. Log Sep 27 14:19:25 Dell-Laptop gammu-smsd[10285]: Going to 30 seconds sleep because of too much connection errors Sep 27 14:19:55 Dell-Laptop gammu-smsd[10285]: Starting phone communication... Sep 27 14:19:55 Dell-Laptop gammu-smsd[10285]: Error at init connection: Error opening device, it doesn't exist. (DEVICENOTEXIST[4])

    Read the article

  • Post Error, Fixed/Removable Media Error

    - by Dan
    Hi, I really do not know what I am missing here. I ordered parts for a new server. The board is an Intel s3420GP. From the diagnostic LEDs I get the error message: 0xB1h which corresponds to "Fixed Media: Disabling fixed media" and 0xB8h which corresponds to "Removable Media: Resetting removable media device." I can not for the life of me figure out what it is talking about. I have two identical motherboards and both gave the error message. I don't have a second CPU yet, so I can't test that. There are no beeps or anything. It seems the server resets every 10 seconds or so (the speaker does work, I put the RAM in the wrong slots on purpose to test this out, and the correct error POST code came up) Please help me, I'm not sure where else to turn or to ask

    Read the article

  • "Request not supported" in IPCONFIG (WinXP SP3)

    - by pablog
    In a customer PC (Windows XP SP3), suddenly the network went down: the network adapter appears with an error mark. I replaced the network card, but the new one does the same thing. When I enter IPCONFIG, XP shows this error (in standard and safe mode): Internal error occurred Request not supported Unable to query host name If I start the system with a boot cd the PC runs fine, so the problem seems to be in the XP installation. I tried: uninstalling and reinstalling the network card in the Device Manager disabling and reenabling the card netsh int ip reset netsh winsock reset catalog and a couple of "reset" programs (WinsockxpFix.exe, etc) with no luck. Is there any way to fix it without reinstalling XP? TIA, Pablo

    Read the article

  • Is span monitoring on Cisco ASA 5520 possible?

    - by Brent
    From what I have read, you can use the switchport monitor command on ASA 5505's to setup a Span port due to the back of the ASA actually being a switch. On my 5520, I do not see the switchport command listed when issuing a ? via the CLI. How do people monitor traffic on non-5505's? My goal is to connect our IDS/IPS device that is running is promiscuous mode to a Ethernet port on the 5520 to monitor WAN traffic. I do not want to have to pass the WAN traffic through a switch as it would require me to get two (for redundancy) STP/switchport capable switches. Guide to setting up switchport access on a 5505: http://www.wr-mem.com/?p=66

    Read the article

  • VPN and Bonjour conflicting

    - by JW.
    Does anyone know why a VPN connection might interfere with Apple's Bonjour? I've noticed that my Mac and various iDevices have trouble finding each other on my local network, when I have VPN connections open. Things like Home Sharing and Wi-Fi Sync work some of the time, but sometimes fail to find the other device. The VPN connections are made using IPSecuritas, which is a GUI around raccoon. I have the local "endpoint mode" set to Host. Apple mentions that Home Sharing may conflict with VPNs, but they don't specify why, or how to fix it. I'm using a Mac with OS 10.7.3 and IPSecuritas to connect to the VPN, an iPhone, and an iPad.

    Read the article

  • fedora liveUSB fails, drops to debug shell

    - by evan
    Trying to install Fedora 15 via a live USB made with unetbootin. I get to the unetbootin boot menu, select Fedora-15-x86_64-Live-Desktop.is, I get to this screen, then it drops into a debug shell with the message sh: can't access tty: job control turned off. The last message is dmseg is dracut Warning: No root device "live:/dev/disk/by-label/Fedora-15-Beta-x86_64-Live-Desktop.is" found. Seems to be the same problem detailed here. Tried to try nk1eto's solution but there is no by-label directory in /dev/disk. There's by-id, by-path and by-uuid.

    Read the article

  • Why is my eth0 getting a dynamic ip when it is configured to be static?

    - by sdek
    For some reason our office linux box is being assigned an ip address via dhcp and I don't know why. What is confusing to me is that when I check system-config-network it shows that my eth0 is setup to be a static ip address. And /etc/sysconfig/network-scripts/ifcfg-eth0 also shows it is setup to be a static ip, yet it is getting a different ip address than the one specified in the ifcfg-eth0. Let me know if you have any suggestions on or ideas on where I can look next. Here are a few details that might help you figure out what an idiot I am :) Fedora 11 Router in front of this box is running dhcp, starting at 10.42.1.100 This box is configured to be 10.42.1.50 (at least I think it is!), subnet 255.255.255.0 (which is same as the router's lan subnet) Instead of having the static IP, this box is getting assigned 10.42.1.100. Here are the ifcfg-eth0 details DEVICE=eth0 BOOTPROTO=none ONBOOT=yes TYPE=Ethernet USERCTL=no NM_CONTROLLED=no NETMASK=255.255.255.0 IPADDR=10.42.1.50 GATEWAY=10.42.1.1

    Read the article

  • How to use Ralink RT2501/RT2573 as wifi access point in Debian Linux

    - by user60813
    Hi, I have a fit-PC server with Debian GNU/Linux (Lenny). I would like to use it as a wifi access point since my Linksys WRT54GS has become unstable. I have a USB Ralink wifi NIC. When I insert the card to USB I can see this with lsusb: Bus 001 Device 002: ID 148f:2573 Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter I have tried following various HOWTOs on using wifi card as AP in Linux, however, it seems that the card cannot go into monitor mode. I believe this is because I must use a newer driver or upload non-free firmware or something like that. I have tried installed wicd, but it does not help. I bought this wifi adapter because I was told that it is one of the most common used Linux supported wifi cards that can be used as access point and a lot of other stuff. So my question is: How do I set up this USB wifi card as wireless access point in Debian Lenny?

    Read the article

  • Booting Linux from External HDD, with persistence

    - by Moriarty
    I am trying to install Linux, specifically Lubuntu or BackTrack 5 on an external HDD (Seagate FreeAgent GoFlex) but I have had no luck using YUMI, or Untebootin to get it working. I want the hard drive to be able to save the data within Linux (As in, If I install a program, it will stay there). I also tried doing this with a flash drive, which does boot, but it does not save data (I tried following Pendrive's tutorial on creating a casper-rw file and adding "persistent" to various files, but I cannot get it to save files. Basically, I just want a form of linux on a portable device that will save files and settings between boots Note: I do not have a CD to install from. Any help would be greatly appreciated, Thanks!

    Read the article

  • European wireless data

    - by drewk
    I am on my way to Europe for 20 days with the wife and teenage kids. Among us, we have 3 iPhones, 1 Blackberry, 2 iPad 3G and 2 Macbook Pro laptops. Each has Skype. I am very concerned about AT&T data charges, and I am looking for a sensible alternative. For example, the AT&T data plans for the phones and iPads are $200 EACH for 200 MB per device. That is $1,200 and does not even cover the laptops. Ouch!!! I am thinking about a prepaid data plan from a European cell system of some sort combined with a GSM data modem and a Cradlepoint router, such as the CTR500. So, questions: 1) Anyone know of a GSM data source in Europe where I can buy a GSM Modem compatible with the CTR500 at a reasonable prepaid rate? 2) Experience with the CTR500?

    Read the article

  • Windows XP waits for usb drive on almost every operation.

    - by Tomasz Kowalczyk
    Hello everyone, I have a problem with my Windows XP operating system, particularly with the USB device that is plugged in - 1TB WD My Book external drive. I haven't found any information about such behaviour when searching in Internet, so I have to ask You. The problem is: when I am using computer, especially during work (programming), when I try to access any information on a hard disk ("internal" one), Windows seems to "consult" it with the external drive. For example, when I open file selection dialog window, if I try to change directory, system activates external drive, reads something (I hear the disk's operational noise) and after some seconds of such pause it makes the operations I requested. There are many situations in which I can reproduce this behavior - opening My Computer, shutting down system, opening partition folder from My Computer - every operation involves the usage of external drive. Please understand me properly - this is not something that happens EVERY time, but at least "many" times a day. What causes such behavior and how can I "turn off" external drive when it's not needed? Thanks in advance for your answers.

    Read the article

  • dd-wrt Bonjour/ netbios etc on two subnets

    - by user72182
    Hi I was wondering if any clever people out there could help me. I have a network setup with two different subnets 192.168.1.0 and 192.168.0.0 one router is connected to a VPN (via OpenVPN) the other is not. Both routers have static routes to each other and a device on one can communicate to another without issues when using IP addresses. My problem is I want to use services like Bonjour, Netbios and Apple Talk across the two networks, which currently does not work. A laptop connected on one subnet will not see a laptop connected on another. Is there anyway that you can connect the two networks together so these sort of local service will work??? I guess I have to forward the boardcast packets but I have no idea how to do this. Thanks for any help...

    Read the article

  • Windows XP detecting printer as USB hub - how to start again without reinstalling XP?

    - by Umber Ferrule
    Fresh install of Windows XP SP3. No system restore. Didn't install USB printer drivers before connected it to PC. Mistakenly allowed XP to auto install some driver which turned out to be a USB hub(!). Now I can't get XP to see the printer as a printer. Have tried uninstalling the offending driver in Device Manager and rebooting but it keeps being detected as a USB hub. How do I revert XP back to a pristine, unsullied USB state so it doesn't know about the USB hub and will (hopefully) install the printer as a printer?

    Read the article

  • Disable PXE progamatically in parallels?

    - by Stefan Lasiewski
    I'm running Parallels 4.0 on Mac OS X 10.5.8. I'm trying to create a bunch of Virtual Machines from the commandline, using the prlctl tool, like so: $ prlctl create test1 -o linux -d centos $ prlctl set test1 --device-del cdrom0 $ prlctl start test1 Now, each time I start a new VM, the VM spends time waiting for a PXE boot. I'd like to turn this off. Can I disable PXE requests using Parallels or a Parallels commandline tool? Or, can I set the boot order of a VM from the commandline?

    Read the article

< Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >