Search Results

Search found 26263 results on 1051 pages for 'linux guest'.

Page 368/1051 | < Previous Page | 364 365 366 367 368 369 370 371 372 373 374 375  | Next Page >

• Very slow disk performance on Dell PowerEdge 2950 w/ PERC 6/i running RAID 10

  - by vocoder

  I recently set up a server running Ubuntu 10.04 LTS on a Dell PowerEdge 2950 server - it has 6 500 gb 7200RPM SATA drives setup in a RAID 10 config. I am seeing extremely poor disk performance - the RAID array reports all disks are normal and using MegaCLI, it looks like the BBU is fine. hdparm -tT /dev/sda reports: Timing cached reads: 90 MB in 2.05 seconds = 43.96 MB/sec Timing buffered disk reads: 24 MB in 3.11 seconds = 7.72 MB/sec So as you can see, it takes forever to something as simple as an apt-get upgrade and even logging into the server. How do I go about troubleshooting what is causing this? I upgraded the firmware on the PERC 6i RAID controller to the latest, but didn't see any improvements.

  Read the article

• rsync general question

  - by CaptnLenz

  I'm trying to use rsync. At first, everything looks very good: rsync -Pniahv -e ssh /home/xxx/Videos/ [email protected]:"/shares/Public/Shared\ Videos/" --stats ... <f+++++++++ Serien/blah.avi <f+++++++++ Serien/blah S01E01 <f+++++++++ Serien/blah - S01E02 <f+++++++++ Serien/blah - S01E03 <f+++++++++ Serien/blah - S01E04 <f+++++++++ Serien/blah - S01E05 <f+++++++++ Serien/blah - S01E06 <f+++++++++ Serien/blah - S01E07 ... Number of files: 232 Number of files transferred: 223 Total file size: 118.24G bytes Total transferred file size: 117.51G bytes Literal data: 0 bytes Matched data: 0 bytes File list size: 9.46K File list generation time: 0.001 seconds File list transfer time: 0.000 seconds Total bytes sent: 10.18K Total bytes received: 712 After that, i copied some of the files manually and runned rsync again in dry mode: rsync -Pniahv -e ssh /home/xxx/Videos/ [email protected]:"/shares/Public/Shared\ Videos/" --stats ... <f..tpo.... Serien/blah.avi <f..tpo.... Serien/blah S01E01 <f..tpo.... Serien/blah - S01E02 <f..tpo.... Serien/blah - S01E03 <f..tpo.... Serien/blah - S01E04 <f..tpo.... Serien/blah - S01E05 <f..tpo.... Serien/blah - S01E06 <f..tpo.... Serien/blah - S01E07 ... Number of files: 232 Number of files transferred: 223 Total file size: 118.24G bytes Total transferred file size: 117.51G bytes Literal data: 0 bytes Matched data: 0 bytes File list size: 9.46K File list generation time: 0.001 seconds File list transfer time: 0.000 seconds Total bytes sent: 10.18K Total bytes received: 712 Why hasn't changed something in the --stats, although only the permissions and the timestamp have to be updated and not the full files need to be copied?

  Read the article

• Accidentally moved FUSE mounted mount point, not cannot unmount. Any option besides reboot?

  - by Catskul

  I mounted a disk image using a few different FUSE modules and then subsequently renamed the parent directory. The mounts have disappeared from the mtab and now the OS refuses to unmount them. fusermount -u mnt returns: fusermount: entry for /home/catskul/foo/mnt not found in /etc/mtab sudo fusermount -u mnt returns: fusermount: failed to unmount /home/catskul/foo/mnt: Device or resource busy sudo fuser -a mnt returns: Cannot stat file /proc/986/fd/55: Permission denied mnt:

  Read the article

• Outlook express-2003 under RHEL 5 server

  - by Kumar P

  I am using RHEL 5 server as proxy server in Local network. Under server i have few windows machines. Now i want to configure Outlook express-2003 for send and receive mails in windows boxes, When i configure and test connections, It showing connection failed. In browser, internet working well. Without proxy, windows outlook express configure well in windows boxes. And working well. What you think about it and How can i solve this problem ? Please give clear steps to solve.

  Read the article

• Supervisor VS cronjob

  - by Guandalino

  Actually I'm using supervisor to monitor a process and restart it when it stops for some reason. The problem is that in case of a supervisor crash the process stops get monitored. So I thought to schedule a cronjob to check supervisor is running, and eventually restart it. The next thing I'm considering is to get rid of supervisor and check my process directly from the cronjob. I read that sometimes supervisor uses too much memory (to be verified, though). What are the pros in having supervisor VS cronjob monitoring the process?

  Read the article

• Kernel config file generator

  - by lisak

  Hey guys, could please anybody recommend some kind of kconfig generator that would trim modules and built-in stuff that is not needed according to current hardware ? The best I have found is this : http://lkml.org/lkml/2008/9/16/290 I don't care about compilation time and the amount of modules that are not built-in. I'm concerned about performance. I don't know how much memory and runtime is wasted on huge kernels with almost everything possible. I'm a java developer and I don't know what most of the modules and drivers are for. So there is not much I can disable and be sure that I don't screw it up. Thanks in advance

  Read the article

• placing shell script under systemd control

  - by Calvin Cheng

  Assuming I have a shell script like this:- #!/bin/sh # cherrypy_server.sh PROCESSES=10 THREADS=1 # threads per process BASE_PORT=3035 # the first port used # you need to make the PIDFILE dir and insure it has the right permissions PIDFILE="/var/run/cherrypy/myproject.pid" WORKDIR=`dirname "$0"` cd "$WORKDIR" cp_start_proc() { N=$1 P=$(( $BASE_PORT + $N - 1 )) ./manage.py runcpserver daemonize=1 port=$P pidfile="$PIDFILE-$N" threads=$THREADS request_queue_size=0 verbose=0 } cp_start() { for N in `seq 1 $PROCESSES`; do cp_start_proc $N done } cp_stop_proc() { N=$1 #[ -f "$PIDFILE-$N" ] && kill `cat "$PIDFILE-$N"` [ -f "$PIDFILE-$N" ] && ./manage.py runcpserver pidfile="$PIDFILE-$N" stop rm -f "$PIDFILE-$N" } cp_stop() { for N in `seq 1 $PROCESSES`; do cp_stop_proc $N done } cp_restart_proc() { N=$1 cp_stop_proc $N #sleep 1 cp_start_proc $N } cp_restart() { for N in `seq 1 $PROCESSES`; do cp_restart_proc $N done } case "$1" in "start") cp_start ;; "stop") cp_stop ;; "restart") cp_restart ;; *) "$@" ;; esac From the bash script, we can essentially do 3 things: start the cherrypy server by calling ./cherrypy_server.sh start stop the cherrypy server by calling ./cherrypy_server.sh stop restart the cherrypy server by calling ./cherrypy_server.sh restart How would I place this shell script under systemd's control as a cherrypy.service file (with the obvious goal of having systemd start up the cherrypy server when a machine has been rebooted)? Reference systemd service file example here - https://wiki.archlinux.org/index.php/Systemd#Using_service_file

  Read the article

• What can go wrong with a GLIBC upgrade?

  - by Sevenless

  I recently installed a piece of software that my group needs for a research project starting next September. Turns out the software has a known crash bug when used with glibc 2.12.1. My boss asked if we can upgrade glibc on the server that's supposed to run it. Cue my skeptical silence.... At some point, I got it into my brain that messing with glibc was about as good an idea as messing with a hungry puma; however, I've been unable to determine the source of this belief. So, if I go ahead with this: Am I doing something flagrantly stupid (e.g. I won't fix my problem, I will brick my server, or I will initiate a zombie apocalypse)? What can go wrong? What is likely to go wrong? How do I avoid the answers to 2 and 3?

  Read the article

• Xinetd , vncserver memory requirement

  - by JP19

  Hi, I am installing the following on a low memory system: vnc4server xinetd xterm openbox obconf I will only occasionally be logging into the vncs for some admin work. My question is: 1) Does xinetd take memory / cpu even when vncserver is not running? If so, can I "run" xinetd on demand (how)? And if no, any idea how much memory it will take when vncserver is not running? 2) Does vncserver take substantial memory when no clients are connected? 3) Do openbox/obconf take memory when vncserver is running but no client are connected? 4) Do openbox/obconf take memory when no vncserver is running? thanks JP

  Read the article

• How to query a DHCP server to get the local DNS serves

  - by Dan Berlyoung

  I have a ClarkConnect (CentOS based) box running as my home router on a RR connection. I had the DNS servers set up to use Google's DNS server. I want to change them back to the local DNS servers but I can't find an obvious/easy way to get those address short of a)reconfiguring the router's network to DHCP them (would rather not interrupt everyone) or b)calling their T/S (kill me now!). Is there a command line tool/command I can use to query the DHCP server on the external NIC to see what DNS servers it would set me up with w/o munging my existing setup?

  Read the article

• How to query a DHCP server to get the local DNS serves

  - by Dan Berlyoung

  I have a ClarkConnect (CentOS based) box running as my home router on a RR connection. I had the DNS servers set up to use Google's DNS server. I want to change them back to the local DNS servers but I can't find an obvious/easy way to get those address short of a)reconfiguring the router's network to DHCP them (would rather not interrupt everyone) or b)calling their T/S (kill me now!). Is there a command line tool/command I can use to query the DHCP server on the external NIC to see what DNS servers it would set me up with w/o munging my existing setup?

  Read the article

• How can I allocate more memory for /dev/sda1 in Ubuntu Hardy Heron?

  - by rvs

  I'd like to make some room on /dev/sda1 without necessarily having to remove a whole bunch of applications (I've already gone through and deleted all frivolous apps). This is the state of /dev/sda1 currently: Dir: / Type: ext3 Total: 9.4GiB Free: 488.6MiB Available: 0bytes Used: 8.9GiB

  Read the article

• Epson Artisan 800 on Ubuntu/Linux

  - by Tim Lytle

  Update for Ubuntu 10.04: Printing should work 'out-of-box', scanning still needs the newer sane backend. Looking for a known good way to setup an Epson Artisan 800 on Ubuntu specifically or any linux box in general. It is a printer/scanner with ethernet/wifi/usb. I'd like to use it as a network printer/scanner being able to do both from my Windows and Ubuntu machines; however, if it needs to be physically connected to a computer (preferably the Ubuntu machine) that is doable (again, then sharing print/scan functions to the network). Basically, I'm looking for someone who has used this printer/scanner (or similar) in a multi-platform environment to share how the set it up and how well it worked. Updated: A little more information, like most printers (I expect) the documentation for the printer basically says, "don't use plug-n-play, run our setup CD from your Windows/Mac system", to do anything (set it up for network use even). I guess that's to make it easy for anyone else to setup, but when you're looking to use it with an unsupported (by Epson's documentation) OS, you're just stuck on your own. What I was hoping for was someone who could say, "Forget the bundled software, do [this] to set it up on wifi manually, install [this] to connect to the scanner from [os], printing works with [this] driver - at least that's how I set it up." I'll will (and have so far) use the information here, and post my own setup when I'm done, if there's no one else out there with that experience.

  Read the article

• External routing for local interfaces in a virtualized network

  - by Arkaitz Jimenez

  Current setup: br0| |-- tun10 -pipe-tun0(192.240.240.1) |-- tun11 -pipe-tun1(192.240.240.2) |-- tun12 -pipe-tun2(192.240.240.3) The pipe program is a custom program that forwards data back2back between two tun interfaces. The idea is puting 2 programs in .2 and .3 while keeping .1 as the local interface in the current machine. The main problem is that I want to route packets to .2 and to .3 through .1 and br0, but as they are local interfaces, the kernel ignores any routing instruction, it just delivers the packet to the proper interface. Tried iptables, but the nat table doesn't even see ping packets to those ifaces. A "ping 192.240.240.2" delivers a icmp packet with source and dest .2 to tun1, ideally it should deliver a source .1 dest .2 at tun1 through tun0-br0-tun1 Any hint? Here the output of some commands: Output

  Read the article

• Graphite Running using daemon tools getting defunct

  - by pradeepchhetri

  I am running carbon-cache.py and carbon-aggregator.py using daemon tools. When I made some changes in the storage-schema.conf and tried to restart the carbon-cache.py, I found that it is becoming zombie very frequently. root 3367 3366 0 03:23 pts/1 00:00:00 supervise carbon-aggregator root 3371 3366 0 03:23 pts/1 00:00:00 supervise carbon-cache root 3373 3367 3 03:23 pts/1 00:00:02 /usr/bin/python /usr/bin/carbon-aggregator.py --debug start root 3379 3372 0 03:23 pts/1 00:00:00 multilog t /var/log/multilog/carbon-cache root 3382 3368 0 03:23 pts/1 00:00:00 multilog t /var/log/multilog/carbon-aggregator root 3638 3371 21 03:24 pts/1 00:00:00 [carbon-cache.py] <defunct> Can someone tell me what may be the reason ?

  Read the article

• Starting my own server - basic recommendations and questions [closed]

  - by Ilia Rostovtsev

  Possible Duplicate: Can you help me with my capacity planning? I'm planning to start my own high-performance server and then use collocation services for keeping it up and running. I'm planning to USE it for processing videos and keeping big video site up! (using FFMpeg, MENcoder and etc.) I just need recommendations on whether listed hardware is good enough and will work together well and fast enough. Do I need anything else (missed something). I remember about CPU coolers though! ;) I'm planning to use SSD drives so please tell me if it's going to work just as regular HDDs (but much faster)? Are they going to be used as RAID (is this possible for SSDs)? Here is what I would like to get: Intel ® Server System SR1600URHSR (Urbanna) or Intel® Server System SR1695WBAC 2 x Intel Xeon X5650 4 x 16Gb DDR-III 1333MHz Kingston ECC Reg (KVR13R9D4/16) 3 x (or maybe 4x) 480Gb SSD Intel 520 Series (SSDSC2CW480A3K5) Which server system would be better? Is listed hardware new/good enough and worth buying it at the moment? Should I probably take a look at something slightly more expensive but more up to date and powerful, may be? After all as software I would like to use CentOS 6 64 bit + WHM/CPanel? Any other suggestions on maybe cheaper and same/more powerful server management system but WHM? What most important points to keep in mind when starting/maintaining your own server?

  Read the article

• pptpd configuration

  - by Ian R.

  I would like a little help on configuring pptp so I can use my server as a vpn server since I have 10 ip's on it and I travel a lot so that would really help me and my partners. I managed to install everything needed but my vpn client fails to connect due to some reason that I cannot understand. I know there are 2 files in pptp that you're supposed to edit so I will post my 2 files here: /etc/ppp/pptpd-options name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 proxyarp nodefaultroute lock nobsdcomp /etc/pptpd.conf option /etc/ppp/pptpd-options logwtmp localip xx.158.177.231 remoteip xx.158.177.103,xx.158.177.116,xx.158.177.121,xx.158.177.124,xx.158.177.125,xx.158.177.131,xx.158.177.134,xx.158.177.139,xx.158.177.142,xx.158.177.145 interfaces file eth0 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.231 Bcast:xx.158.177.255 Mask:255.255.254.0 inet6 addr: xx80::216:3eff:fe51:31ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:56352 errors:0 dropped:0 overruns:0 frame:0 TX packets:3xx15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4884030 (4.8 MB) TX bytes:6780974 (6.7 MB) Interrupt:16 eth0:1 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.103 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:2 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.116 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:3 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.121 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:4 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.124 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:5 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.125 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:6 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.131 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:7 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.134 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:8 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.139 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:9 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.142 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:10 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.145 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:286 (286.0 B) TX bytes:286 (286.0 B)

  Read the article

• How to secure Firefox traffic (+DNS) through SOCKS proxy under Ubuntu 10.04?

  - by Maarx

  I'm using Ubuntu 10.04, and starting a SOCKS proxy with 'ssh -D', and setting Ubuntu to use it with "System - Preferences - Network Proxy". Firefox uses the proxy, and the proxy's IP appears when I visit a site like http://www.whatismyip.com/. My question is, is Firefox resolving DNS requests through this proxy? Is my web-browsing truly secure? (That is, until I exit the other end of the proxy. I know it's insecure after that.) (And I've verified the keys, I'm not being man-in-the-middled) (And--screw it. You know what I mean. Is it resolving DNS requests through the proxy?) I don't know how I would go about verifying such a thing for myself. Using additional hardware such as another debugging proxy is not an option. If Firefox isn't resolving my DNS requests through the SOCKS proxy, how do I go about fixing it?

  Read the article

• apache2 slow responding (debian)

  - by baloo

  I'm running an apache2 2.2.9 webserver with modpython and mpm_worker_module. The current config for the mpm is ServerLimit 32 StartServers 10 MaxClients 800 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 The server has 1G of ram and a 100Mbit connection. Checking netstat -na | grep ESTABLISHED | wc -l gives me a number between 50 - 60. The load is about 1.0 Every pageload is also cached by memcached. I can't see why the server is so slow in responding to new connections, sometimes droping them completely? Also tried disabling iptables to make sure it's not because of a full state table or something like that. The only thing in dmesg is a lot of spam about "TCP: Treason uncloaked!"

  Read the article

• How do i set up a fully featured small business network?

  - by JoshReedSchramm

  This has the possibility to be a very large question but I recently acquired a few rack mount servers and the hardware necessary to run them. Unfortunately I'm a programmer with very little understanding of how to set up a good working network so I'm hoping someone on here might be able to help. What I want to do is run a domain with a series of subdomains which would all be externally accessible. The setup would live inside my home and my internet connection is your run of the mill cable model (which means a dynamic IP) I want to be able to set up a couple site, specifically: www.mycompany.com (mycompany.com with no subdomain would redirect to this) build.mycompany.com (for my continuous integration server) ruby.mycompany.com (for ruby projects) win.mycompany.com (for windows project) etc. Additionally this is still my home network so our personal machines need to be able to get on via wifi with at least the same security we have now through an out of the box router from best buy. I'm thinking i need a DNS server, DHCP server and one of those would run either no-ip or dyndns to accommodate the dynamic ip. I don't necessarily need mail but it might be helpful to have some sort of mail server i could use for testing, it doesn't need to get out to the greater internet though. So how do i set up this kinda of network? tl;dr Need to know how to set up your standard office style network in my home off my normal consumer level cable modem connection.

  Read the article

• Iptables: "-p udp --state ESTABLISHED"

  - by chris_l

  Hi, let's look at these two iptables rules which are often used to allow outgoing DNS: iptables -A OUTPUT -p udp --sport 1024:65535 --dport 53 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -p udp --sport 53 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT My question is: How exactly should I understand the ESTABLISHED state in UDP? UDP is stateless. Here is my intuition - I'd like to know, if or where this is incorrect: The man page tells me this: state This module, when combined with connection tracking, allows access to the connection tracking state for this packet. --state ... So, iptables basically remembers the port number that was used for the outgoing packet (what else could it remember for a UDP packet?), and then allows the first incoming packet that is sent back within a short timeframe? An attacker would have to guess the port number (would that really be too hard?) About avoiding conflicts: The kernel keeps track of which ports are blocked (either by other services, or by previous outgoing UDP packets), so that these ports will not be used for new outgoing DNS packets within the timeframe? (What would happen, if I accidentally tried to start a service on that port within the timeframe - would that attempt be denied/blocked?) Please find all errors in the above text :-) Thanks, Chris

  Read the article

• Sub-process /usr/bin/dpkg returned an error code (1)

  - by rohit

  Hey friends i am getting the following error when i am trying to purge shorewall root@aptosid:/etc# apt-get purge shorewall Reading package lists... Done Building dependency tree Reading state information... Done The following packages will be REMOVED: shorewall* 0 upgraded, 0 newly installed, 1 to remove and 3 not upgraded. 1 not fully installed or removed. After this operation, 1,843 kB disk space will be freed. Do you want to continue [Y/n]? (Reading database ... 212702 files and directories currently installed.) Removing shorewall ... : not found/shorewall: 25: /etc/default/shorewall: :q Stopping "Shorewall firewall": not done (check /var/log/shorewall-init.log). invoke-rc.d: initscript shorewall, action "stop" failed. dpkg: error processing shorewall (--purge): subprocess installed pre-removal script returned error exit status 1 configured to not write apport reports Errors were encountered while processing: shorewall E: Sub-process /usr/bin/dpkg returned an error code (1) root@aptosid:/etc# please help me out ...........?

  Read the article

• Problem with testsaslauthd and kerberos5 ("saslauthd internal error")

  - by danorton

  The error message “saslauthd internal error” seems like a catch-all for saslauthd, so I’m not sure if it’s a red herring, but here’s the brief description of my problem: This Kerberos command works fine: $ echo getprivs | kadmin -p username -w password Authenticating as principal username with password. kadmin: getprivs current privileges: GET ADD MODIFY DELETE But this SASL test command fails: $ testsaslauthd -u username -p password 0: NO "authentication failed" saslauthd works fine with "-a sasldb", but the above is with "-a kerberos5" This is the most detail I seem to be able to get from saslauthd: saslauthd[]: auth_krb5: krb5_get_init_creds_password: -1765328353 saslauthd[]: do_auth : auth failure: [user=username] [service=imap] [realm=] [mech=kerberos5] [reason=saslauthd internal error] Kerberos seems happy: krb5kdc[](info): AS_REQ (4 etypes {18 17 16 23}) 127.0.0.1: ISSUE: authtime 1298779891, etypes {rep=18 tkt=18 ses=18}, username at REALM for krbtgt/DOMAIN at REALM I’m running Ubuntu 10.04 (lucid) with the latest updates, namely: Kerberos 5 release 1.8.1 saslauthd 2.1.23 Thanks for any clues.

  Read the article

• How to use the correct SSH private key?

  - by Dail

  I have a private key inside /home/myuser/.ssh/privateKey I have a problem connecting to the ssh server, because i always get: Permission denied (publickey). I tried to debug the problem and i find that ssh is reading wrong file, take a look at the output: [damiano@Damiano-PC .ssh]$ ssh -v root@vps1 OpenSSH_5.8p2, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for vps1 debug1: Applying options for * debug1: Connecting to 111.111.111.111 [111.111.111.111] port 2000. debug1: Connection established. debug1: identity file /home/damiano/.ssh/id_rsa type -1 debug1: identity file /home/damiano/.ssh/id_rsa-cert type -1 debug1: identity file /home/damiano/.ssh/id_dsa type -1 debug1: identity file /home/damiano/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 74:8f:87:fe:b8:25:85:02:d4:b6:5e:03:08:d0:9f:4e debug1: Host '[111.111.111.111]:2000' is known and matches the RSA host key. debug1: Found key in /home/damiano/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/damiano/.ssh/id_rsa debug1: Trying private key: /home/damiano/.ssh/id_dsa debug1: No more authentication methods to try. as you can see ssh is trying to read: /home/damiano/.ssh/id_rsa but i don't have this file, i named it differently. How could I tell to SSH to use the correct private key file? Thanks!

  Read the article

• Dovecot not working pop3 with postfix

  - by samer na

  $ telnet localhost pop3 Trying ::1... Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection refused $ netstat -l tcp 0 0 *:www : LISTEN tcp 0 0 localhost.localdoma:ipp : LISTEN tcp 0 0 *:smtp : LISTEN tcp 0 0 localhost.localdo:mysql : LISTEN and nothing about dovecot in mail.log or mail.err when I run this service dovecot start I got start: Rejected send message, 1 matched rules; type="method_call", sender=":1.553" (uid=1000 pid=26250 comm="start) interface="com.ubuntu.Upstart0_6.Job" member="Start" error name="(unset)" requested_reply=0 destination="com.ubuntu.Upstart" (uid=0 pid=1 comm="/sbin/init")) in dovecot.conf protocols = imap imaps pop3 pop3s disable_plaintext_auth = no log_timestamp = "%Y-%m-%d %H:%M:%S " mail_location = maildir:/var/spool/mail/%d/%n mail_access_groups = mail first_valid_uid = 106 first_valid_gid = 106 protocol imap { } protocol pop3 { listen=*:110 pop3_uidl_format = %08Xu%08Xv } protocol lda { postmaster_address = [email protected] mail_plugins = quota log_path = /var/log/dovecot-deliver.log info_log_path = /var/log/dovecot-deliver.log } auth default { mechanisms = digest-md5 plain passdb sql { args = /etc/dovecot/dovecot-mysql.conf } userdb sql { args = /etc/dovecot/dovecot-mysql.conf } user = root }

  Read the article

< Previous Page | 364 365 366 367 368 369 370 371 372 373 374 375  | Next Page >