Search Results

Search found 21809 results on 873 pages for 'display interfaces'.

Page 382/873 | < Previous Page | 378 379 380 381 382 383 384 385 386 387 388 389  | Next Page >

• Unable to recognize hard drive after replacing a drive

  - by Peter Schriver

  I have a Poweredge 830 that I had been using with 1 OS Sata drive and 3 data drives. One of the drives had some failing sectors so I replaced it with a different drive. For some bizarre reason the computer would not reboot so I disconnected all of the media drives and did a clean reinstall on the OS drive. Only the boot drive and one of the media drives are now recognized by my Bios. Drive 0 and 2. Drive 1 and 3 are listed in the Bios as "Unkown Device" Any help would be appreciated I think there may be something wrong with the install. For some reason when I attempt to change the display it says I have a laptop.If you think a reinstall is in order I will try that.

  Read the article

• Configuring https access on HP A5120 Switch

  - by GerryEgan

  I am trying to configure HTTPS management on a HP a5120 switch running Version 5.20.99, Release 2215 and not having much luck. I have followed the manual by creating an SSL policy first and then enabling the HTTPS server with the SSL policy: ssl server-policy sslpol ip https ssl-server-policy sslpol ip https enable When I try and log onto the switch with Google Chrome I get the following error: Error 107 (net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error. When I look this up I have found references to errors due to TLS being used in SSL. I can find no way to specify the SSL version in the server policy. The manual has a configuration example that uses MSCEP to retrieve a certificate but in Windows 2008 R2 that feature is only available in Enterprise and Datacentre editions which I don't have. I have SSH configured and it is using a locally generated certificate so I'm not sure if I can use that but I'd like to if possible. Has anybody been able to setup HTTPS management on HP A series switches without MSCEP? Any and all help appreciated! here is a copy of my config with the interfaces removed: version 5.20.99, Release 2215 # sysname MYSYSNAME # irf domain 10 irf mac-address persistent timer irf auto-update enable undo irf link-delay # domain default enable system # telnet server enable # vlan 1 # vlan 100 description Management # radius scheme system primary authentication 127.0.0.1 1645 primary accounting 127.0.0.1 1646 user-name-format without-domain # domain system access-limit disable state active idle-cut disable self-service-url disable # user-group system group-attribute allow-guest # local-user admin password cipher authorization-attribute level 3 service-type ssh telnet terminal service-type web # stp enable # ssl server-policy sslpol pki-domain MYDOMAIN # interface NULL0 # interface Vlan-interface199 ip address 192.168.199.140 255.255.255.0 # interface GigabitEthernet1/0/1 poe enable stp edged-port enable # interface Ten-GigabitEthernet2/1/2 # dhcp-snooping # ntp-service unicast-server 192.168.1.71 # ssh server enable # ip https ssl-server-policy sslpol ip https enable # load xml-configuration # user-interface aux 0 1 user-interface vty 0 15 authentication-mode scheme

  Read the article

• Load balanced IIS. Should I use NLB, or linux-based reverse proxy, or something else?

  - by growse

  What would be the best approach for load-balancing at least 2-3 Windows 2008 R2 IIS webservers running a multitude of .NET applications? My choices appear to be: 1) Hardware-based network device load balancer, like a Cisco CSS 2) Windows NLB 3) Some sort of linux based proxy, either haproxy or other The three servers sit as VMs on a vSphere farm, so I have the ability to clone to up the instance count in times of high load. I control the switch that the vSphere hosts are plugged into (Cisco 3750), but don't control the switching/routing infrastructure beyond that to the clients. (1) Is too expensive, and probably overkill for my needs. I've included this in case someone figures out a cunning way to do it on my existing network kit, which I doubt. (2) would seem to be the obvious "built-in" option, but seems to be quite fiddly messing around with network interfaces, multicast, and generally other things that seem to be needlessly complex. It's also fairly stupid, in that it can't remove hosts from the pool if they start throwing 500 errors or otherwise go wrong (3) is the most interesting option, as it would appear to offer the most flexibility and customizability, but without having to mess around with the network. However, while I'm familiar with the reverse-proxy capabilities of lighttpd etc, I'm not that well read on other options like HAProxy, which might be able to offer a lot more. Which would you go for, and is there anything I've not thought of?

  Read the article

• Fails to boot after upgrade, stuck on winbind package

  - by Praetorian

  I started the upgrade from 11.04 to 11.10 last night. Once it got the installing packages part I left the computer unattended the rest of the night. When I checked it this morning the screen was blank and I couldn't get it to turn on. So I cycled power, and now I get the "Ubuntu 11.10" screen with the dots underneath, but then it gets to a blank screen and nothing more. I can get to the command line in recovery mode; here's a list of the things I've tried so far sudo apt-get update - the very first repository it checked sat at 0% for a long time (network cable is plugged in), so I cancelled with Ctrl+C Thought it might be a problem with display drivers, so I tried sudo apt-get install nvidia-glx - this gave me an error saying dpkg has been interrupted, manually run sudo dpkg --configure -a sudo dpkg --configure -a this installed / updated a bunch of stuff but got stuck at Starting Winbind daemon winbind Restarted and tried sudo dpkg --configure -a again but it gets stuck at same Windbind step What else can I do to fix this problem?

  Read the article

• Error: type or namespace name 'AssemblyKeyFileAttribute' and 'AssemblyKeyFile' could not be found

  To associate an assembly with a strong key file to store it to GAC, we use should include following line after all the imports and before defing namespace. For VB.NET:  <Assembly: AssemblyKeyFile("c:\path\mykey.snk")> For C#:    [assembly: AssemblyKeyFile(@"c:\path\mykey.snk")] but, you might encounter following two errors at the time of creating Assembly for GAC. 1. The type or namespace name 'AssemblyKeyFileAttribute' could not be found (are you missing a using directive or an assembly reference?) 2. The type or namespace name 'AssemblyKeyFile' could not be found (are you missing a using directive or an assembly reference?) How to resolve these errors: Just include "System.Reflection" namespace. It resolve above two errors. span.fullpost {display:none;}

  Read the article

• How do I specify the emergency location in CDP?

  - by chrish

  In the LLDP-MED and Cisco Discovery Protocol whitepaper, it compares LLDP-MED and CDP. The part I am interested in is emergency location configuration. In LLDP-MED, I can specify the Emergency Line Indentification Number (ELIN) and that number will be used by some IP Phones (e.g. Aastra) when placing emergency calls. The whitepaper states: Location Identification Discovery This capability is important because it normally provides location information from the switch to the phone. (If the phone is configured with location information or can determine its location, then it may send this information to the switch. However, the real value is getting this information from the switch to the phone for phones that cannot determine their own location.) Location identification discovery allows the phone to be aware of its location-information that can be used for location-based applications on the phone. More importantly, this capability can be used to provide location information when making emergency calls. Both Cisco Discovery Protocol and LLDP-MED support the transportation of location information. However, LLDP-MED has more supported data formats than Cisco Discovery Protocol. I have found the documentation on how to set the location and associate the location to the interfaces for LLDP-MED. How is this done for CDP? Is ELIN supported for CDP?

  Read the article

• Ubuntu does not work with Nvidia drivers, gives random squares after logging in

  - by jimbo

  I tried installing both with wubi and by booting from a usb drive. After I tried both it was the same. Ubuntu tried to login, but after a while, a weird pattern with squarely shapes appeared. At one point, after using recovery mode and then the low graphics one (i don't remember how it was called exactly) i managed to get in. It still didn't display at correct resolution, and the mouse was invisible at times. However, after rebooting once, because i tried downloading the nvidia drivers, i didn't manage to get in again, so i have the same problem... I have no idea what to try to become unstuck. The main problem is that after the login, ubuntu crashes, with a screen full of randomly coloured squares. Should I just give up?

  Read the article

• Assistance on setup to Connect an offsite server to the LAN via RRAS VPN - Server 2008 R2

  - by Paul D'Ambra

  I have an office LAN protected using a Zyxel Zywall USG 300. I've set up an L2TP/ipsec VPN on that which accepts connections using a shared secret and I've tested this from multiple clients. I have a server offsite and want to set up RRAS to use a persistent connection to the VPN so that it can carry out network jobs even with no one logged in (I'm using it for Micorosft DPM secondary backup). If I create a vpn as if I were setting up a users laptop it can dial in no problem but if I set up a demand dial interface in RRAS it errors. I enable RRAS ticking only demand dial interface (branch office routing) Select network interfaces, right click and choose new demand dial interface Name the VPN ToCompany Select connect using VPN And then L2TP as the vpn type enter the IP address (double-checked for typos!) select Route IP packets on this interface specify static route to remote network as 10.0.0.0/24 with metric of 1 add dial out credentials (again double checked for typos and confirmed with other vpn connections click finish now I right-click on the new interface and choose properties and then the security tab I change Data encryption to optional select only PAP for Authentication (both as per manufacturer of Zywall) click advanced settings against type of vpn and set shared secret then I select the new interface, right-click and choose connect this dials and then errors with either 720 or 811 as the error codes. However, if I create a VPN by going to Network & Sharing center and setting up as if I was creating a VPN from my laptop to the office (say) it dials successfully so I know the VPN settings are correct and the machine can connect to the VPN. Suggests very strongly the problem is how I'm setting up RRAS. Can anyone help?

  Read the article

• Java Alphabetize Algorithm Insertion sort vs Bubble Sort

  - by Chris Okyen

  I am supposed to "Develop a program that alphabetizes three strings. The program should allow the user to enter the three strings, and then display the strings in alphabetical order." It's instructed that I need to use the String library compareTo()/charAt()/toLowerCase() to make all the characters lowercase so the Lexicon comparison is also a alphabetical comparison. Input Pseudo Code: String input[3]; Scanner keyboard = new Scanner(System.in); System.out.println("Enter three strings: "); for(byte i = 0; i < 3; i++) input[i] = keyboard.next() The sorting would be Insertion Sort: 321 2 3 1 2 31 231 1 23 1 2 3 1 23 1 23 123 Bubble Sort 321 231 213 123 Which would be more efficient in this case? The bubble sort seems to be more efficient though they seem to have equal stats for worst best and avg case, but I read the Insertion Sort is quicker for small amounts of data like my case.

  Read the article

• Weird unexpected image compression on a web server running Apache on Ubuntu?

  - by Billy Bob Thornton

  I have a weird problem on my production web server running Apache on Ubuntu: it compresses my images thereby dramatically lowering their quality! Actually I have two virtual hosts running, each located in a different folder. Wether I display .gif images by navigating on the two sites, or acceding them directly by their url, their size and quality are invariably degraded. I tried with three different browsers: same problem. Using them on other sites on the Web: no problem. Of course I disabled mod_deflate on the server (which should not compress images anyway), but the phenomenon remains. On my local développement server, running the same configuration, everything is Ok. Now I'm completely lost! For the record, my configuration: Ubuntu 10.04, Apache 2, Php 5.

  Read the article

• Cisco ASA 8.2 ACL For NAT

  - by javano

  Sadly I have gone back in time to ASA 8.2(5)33 which I am not so familiar with. I have configured NAT between two interfaces but traffic isn't passing becasue I can't get the ACL to work; (The full config which isn't very big is here but to keep this post tidy I have just pasted the important parts below); interface Ethernet0/0 switchport access vlan 108 ! interface Ethernet0/6 switchport access vlan 104 ! interface Ethernet0/7 switchport access vlan 105 ! interface Vlan104 description BUILDING2 nameif BUILDING2 security-level 0 ip address 10.104.0.1 255.255.255.0 ! interface Vlan105 description BUILDING1 nameif BUILDING1 security-level 0 ip address 10.105.0.1 255.255.255.0 ! interface Vlan108 description Main LAN VLAN nameif lan security-level 0 ip address 172.22.0.215 255.255.255.0 ! object-group network obj_net_Remote_Hosts network-object host 111.111.111.3 network-object host 111.111.111.65 object-group network obj_host_pc1_eth1 network-object host 10.104.0.111 object-group network obj_host_pc2_eth1 network-object host 10.104.0.112 object-group network obj_host_pc3_eth1 network-object host 10.104.0.106 object-group network obj_host_pc4_eth1 network-object host 10.104.0.107 object-group network obj_net_PCs description IPs of PCs group-object obj_host_pc1_eth1 group-object obj_host_pc2_eth1 group-object obj_host_pc3_eth1 group-object obj_host_pc4_eth1 access-list acl_NAT_pc1_91 extended permit tcp host 10.104.0.111 host 111.111.111.3 eq 8101 access-list acl_Permit_PCs extended permit tcp object-group obj_net_PCs object-group obj_net_Remote_Hosts eq 8101 ! global (BUILDING1) 11 111.111.222.91 netmask 255.255.255.255 nat (BUILDING2) 11 access-list acl_NAT_pc1_91 access-group acl_Permit_PCs in interface BUILDING2 route BUILDING1 111.111.111.3 255.255.255.255 10.105.0.2 1 route BUILDING1 111.111.111.65 255.255.255.255 10.105.0.2 1 When I try and connect from PC1 to ip 111.111.111.3 I see the following error logged on the ASA console; %ASA-2-106001: Inbound TCP connection denied from 10.104.0.111/38495 to 111.111.111.3/8101 flags SYN on interface blades What the duce!

  Read the article

• my wiki site using mediawiki - databases not found error

  - by Jayapal Chandran

  I had been using mediawiki opensource in my website to display programming articles. Today i tried to access my site but it showed database not found. Mediawiki uses many databases. When i logged in my control panel and checked i can see that most of the databases created by mediawiki is missing so is the reason i am getting this error. I have used mediawiki for two different purposes. It is like two modules. For one the databases are missing and for the other i think the data is corrupt. Do anybody know any issue with mediawiki security or would this be a problem with the webhosting cause we have faced several problems with them initially like before three years and recently the were good. Yet this happened. I have requested to hosting company to look into it and meanwhile i am expecting the help from stackexchange users. How do i check the logs for table deletion?

  Read the article

• Why do I get the result zero when I try to get the width of a DropDownList control in asp.net?

  - by Paul Jack

  After I click button1, it display 0, why? How can get correct width of a DropDownList control? Thanks! <%@ Page Language="C#" AutoEventWireup="true" CodeFile="Default2.aspx.cs" Inherits="Default2" % Item 1 Item 2 </div> </form> using System; using System.Collections.Generic; using System.Linq; using System.Web; using System.Web.UI; using System.Web.UI.WebControls; public partial class Default2 : System.Web.UI.Page { protected void Page_Load(object sender, EventArgs e) { } protected void Button1_Click(object sender, EventArgs e) { Button1.Text = DropDownList1.Width.Value.ToString(); } }

  Read the article

• OpenVPN with MacOS X Client and same subnets in local and remote net.

  - by Daniel

  I have a homenetwork 192.168.1.0/24 with gteway 192.168.1.1 and a remote network with the same parameters. Now I want to create a OpenVPN tunnel between those networks. I have no problems with Windows, because Windows routes everything to 192.168.1.0/24 except 192.168.1.1 throught the tunnel. On MacOS X however I see the folling line in the Details window: 2010-05-10 09:13:01 WARNING: potential route subnet conflict between local LAN [192.168.1.0/255.255.255.0] and remote VPN [192.168.1.0/255.255.255.0] When I list the routes I get the following: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.1.1 UGSc 13 3 en1 127 localhost UCS 0 0 lo0 localhost localhost UH 12 3589 lo0 169.254 link#5 UCS 0 0 en1 192.168.1 link#5 UCS 1 0 en1 192.168.1.1 0:1e:e5:f4:ec:7f UHLW 13 17 en1 1103 192.168.1.101 localhost UHS 0 0 lo0 192.168.6 192.168.6.5 UGSc 0 0 tun0 192.168.6.5 192.168.6.6 UH 1 0 tun0 My Interfaces are en1 - My local Wifi network tun0 - The tunnel interface As can be seen from the routes above there is no entry for 192.168.1.0/24 that routes the traffic through the tunnel interface. When I manually route a single IP like 192.168.1.16 over the tunnel gateway 192.168.6.6, this works. Q: How do I set up my routes in MacOS X for the same behaviour as on windows, to route everything except 192.168.1.1 through the tunnel, but leave the default gateway to be my local 192.168.1.1 ?

  Read the article

• C++ Game engine time scale

  - by I Phantasm I

  i have begun creating a very simple game engine and i am trying to work out how to create a time scale for the game.by time scale i mean some way of increasing and decreasing the speed of the game(not the fps) like creating a slow motion effect ... i have no idea how this could be accomplished so any help would be appreciated. if this help im using windows, Opengl and C++ in the game engine... How my engine is setup i have an update and draw function...update is called 25 times per second while display is called as much as possible.

  Read the article

• Unity doesn't autostart on second X screen

  - by Nonoo

  I have two Nvidia cards both with 2 heads and both configured as TwinView, so I have Screen0 and Screen1 in my xorg.conf. ccsm sees both screens (displays them in the Screens drop-down at the top left), but Unity starts only on Screen0 by default. The displays on Screen1 only show the default white screen and default X mouse cursor, when I hover over them. Is this the normal, expected behavior? Can I start Unity on Screen1 automatically without running custom shell scripts (like DISPLAY=:0.1 compiz --replace)?

  Read the article

• Network to network VPN Centos 5

  - by Atul Kulkarni

  I am trying to follow "http://www.centos.org/docs/5/html/Deployment_Guide-en-US/ch-vpn.html#s1-ipsec-net2net" I have come up with the following On local router machine: in my ifcfg-ipsec0: ONBOOT=yes IKE_METHOD=PSK DSTGW=10.5.27.1 SRCGW=10.6.159.1 DSTNET=10.5.27.0/25 SRCNET=10.6.159.0/24 DST=205.X.X.X TYPE=IPSEC I have /etc/sysconfig/network-scripts/keys-ipsec0 file in place. On Remote Machine in the cloud if have /etc/sysconfig/network-scripts/ifcfg-ipsec1: TYPE=IPSEC ONBOOT=yes IKE_METHOD=PSK SRCGW=10.5.27.1 DSTGW=10.6.159.1 SRCNET=10.5.27.124/25 DSTNET=10.6.159.0/24 DST=38.x.x.x with its respective /etc/sysconfig/network-scripts/key-ipsec1 file. The DST in both cases are NAT'd external IPs. Is that a problem? I have made changes for port forwarding as well. When I try to bring the interfaces up it gives me output "RTNETLINK answers: Invalid argument". I am confused now and don't know what more to do? Any place I can digup what parameters were wrong? I really appreciate any help I can get. Thanks and Regards, Atul.

  Read the article

• Will Unity allow users to change the color/appearance of the top-Panel?

  - by Sam

  I'm very excited by the functional design principles and keyboard shortcuts that are being implemented for Unity. And function of use is more important to me than looks. However, after experiencing the aesthetic beauty of the display of the top panel in gnome-shell, I was wondering if users would be able to alter the color of Unity's top panel? IMHO it does not look as good as the gnome-shell implementation (or mac OS X/iPad). I think if an alternate color/appearance were chosen for the panel, it would make a big difference aesthetically. Is there a way to make it Black like gnome-shell? Or are the color choices limited to theme-designs as pointed out in this answer? For efficiency and clarity, the Panel should be better differentiated from application controls. The panel should be a different color because it has a "constant (always present) state," unlike application controls. For contrast and easy-recognition, I would like to make the Panel black (like gnome-shell) but make the application controls (e.g., those of Firefox) "Inverted"

  Read the article

• How to Apply a Business Card Template to a Contact and Customize it in Outlook 2013

  - by Lori Kaufman

  If you want to add a business card template to an existing contact in Outlook, you can do so without having to enter all of the information again. We will also show you how to customize the layout and format of the text on the card. Microsoft provides a couple of business card templates you can use. We will use their Blue Sky template as an example. To open the archive file for the template you downloaded, double-click on the .cab file. NOTE: You can also use a tool like 7-Zip to open the archive. A new Extract tab becomes available under Compressed Folder Tools and the files in the archive are listed. Select the .vcf file in the list of files. This automatically activates the Extract tab. Click Extract To and select a location or select Choose location if the desired location is not on the drop-down menu. Select a folder in which you want to save the .vcf file on the Copy Items dialog box and click Copy. NOTE: Use the Make New Folder button to create a new folder for the location, if desired. Double-click on the .vcf file that you copied out of the .cab archive file. By default, .vcf files are associated with Outlook so, when you double-click on a .vcf file, it automatically opens in a Contact window in Outlook. Change the Full Name to match the existing contact to which you want to apply this template. Delete the other contact info from the template. If you want to add any additional information not in the existing contact, enter it. Click Save & Close to save the contact with the new template. The Duplicate Contact Detected dialog box displays. To update the existing contact, select the Update information of selected Contact option. Click Update. NOTE: If you want to create a new contact from this template, select the Add new contact option. With the Contacts folder open (the People link on the Navigation Bar), click Business Card in the Current View section of the Home tab. You may notice that not all the fields from your contact display on the business card you just updated. Double-click on the contact to update the contact and the business card. On the Contact window, right-click on the image of the business card and select Edit Business Card from the popup menu. The Edit Business Card dialog box displays. You can change the design of the card, including changing he background color or image. The Fields box allows you to specify which fields display on the business card and in what order. Notice, in our example, that Company is listed below the Full Name, but no text displays on the business card below the name. That’s because we did not enter any information for Company in the Contact. We have information in Job Title. So, we select Company and click Remove to remove that field. Now, we want to add Job Title. First, select the field below which you want to add the new field. We select Full Name to add the Job Title below that. Then, we click Add and select Organization | Job Title from the popup menu to insert the Job Title. To make the Job Title white like the name, we select Job Title in the list of Fields and click the Font Color button in the Edit section. On the Color dialog box, select the color you want to use for the text in the selected field. Click OK. You can also make text bold, italic, or underlined. We chose to make the Job Title bold and the Full Name bold and italic. We also need to remove the Business Phone because this contact only has a mobile phone number. So, we add a Mobile Phone from the Phone submenu. Then, we need to remove enough blank lines so the Mobile Phone is visible on the card. We also added a website and email address and removed more blank lines so they are visible. You can also move text to the right side of the card or make it centered on the card. We also changed the color of the bottom three lines to blue. Click OK to accept your changes and close the dialog box. Your new business card design displays on the Contact window. Click Save & Close to save the changes you made to the business card for this contact and close the Contact window. The final design of the business card displays in the Business Card view on the People screen. If you have a signature that contains the business card for the contact you just updated, you will also need to update the signature by removing the business card and adding it again using the Business Card button in the Signature editor. You can also add the updated Business Card to a signature without the image or without the vCard (.vcf) file.     

  Read the article

• cannot connect to <server_name>\sqlexpress

  - by Jackson Sunuwar

  I have tried disabling firing wall and checked sqlbrowser is started but for some reason I cannnot connect to my datbase... called server_name\sqlexpress.. I have a virtual machine and a full scale MS SQL Server 2008 R2 running on it... and I have several other vm running sqlexpress. they run fine and I can connect to them using sqlexpress... but when i try to access from sqlserver... I get this error. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) Digging deep into the error, I found this Error Number: -1 Severity: 20 State: 0 and finally this... Program Location: at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection) at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj) at System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, SqlConnection owningObject) at System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, Boolean ignoreSniOpenTimeout, Int64 timerExpire, SqlConnection owningObject) at System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(String host, String newPassword, Boolean redirectedUserInstance, SqlConnection owningObject, SqlConnectionString connectionOptions, Int64 timerStart) at System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(SqlConnection owningObject, SqlConnectionString connectionOptions, String newPassword, Boolean redirectedUserInstance) at System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, Object providerInfo, String newPassword, SqlConnection owningObject, Boolean redirectedUserInstance) at System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection) at System.Data.ProviderBase.DbConnectionFactory.CreateNonPooledConnection(DbConnection owningConnection, DbConnectionPoolGroup poolGroup) at System.Data.ProviderBase.DbConnectionFactory.GetConnection(DbConnection owningConnection) at System.Data.ProviderBase.DbConnectionClosed.OpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory) at System.Data.SqlClient.SqlConnection.Open() at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerService.ValidateConnection(UIConnectionInfo ci, IServerType server) at Microsoft.SqlServer.Management.UI.ConnectionDlg.Connector.ConnectionThreadUser() Firewall is turned off on the VM that's running mssqlserver... I turned of firewall on one of the vm that's running the sqlexpress but I still get the error... can someone please help... thank you

  Read the article

• Dual Monitor/Xinerama not working; cannot even detect on-board graphic card

  - by Steven H

  I have Kubuntu 12.04 and two identical VGA monitors. One I plugged via DVI-VGA adapter into the DVI port of my discrete AMD Radeon HD 6670, the other into the VGA port of my on-board graphic card (Radeon HD 6410D). After installing Kubuntu I got a black screen, so I booted with nomodeset and installed AMD's catalyst drivers but only the monitor plugged into the discrete graphic card worked. Using lspci I saw that the on-board graphics was not listed. Then I found in the BIOS settings the options "Surround View" and "Onboard Dual Link DVI" both disabled. After enabling both, the on-board graphics card shows up in lspci but in amdcccle, it only shows as [Uknown display]Uknown adapter. When I try to enable xinerama, I get a black screen after rebooting on both monitors. I tried several options and hints from the web but nothing worked so far. I also reinstalled the AMD drivers several times. What should I do?

  Read the article

• Hardware needed to route between two networks over wireless

  - by AptDweller

  I recently rented an apartment about 100 yards from my brother's house. I have line of sight to his house and can pick up his home AP signal with one of my two laptops if I go out on my balcony (facing his house) or put the laptop by the window. The other laptop will sometimes see the SSID broadcast, but fails to connect, drops, etc. We would like to set up a persistent wireless connection between our homes. We would prefer each network be logically segmented as independent networks, but he will share his internet connection. I've got a bunch of tv shows saved to a NAS by my TiVO that I'd like to make available to him across the wireless link. My brother strongly prefers to not mess with his WAP at all. His network is running fine and is afraid to mess it up. I guess you could say he is "technologically declined". If we can get a reliable 11Mbps connection we will be satisfied. What hardware do I need to make this work? I was thinking a router with two wireless interfaces (external antennas) a wired interface, and a directional antenna mounted on my balcony facing his house. Can anyone recommend hardware to make this happen? Cheaper is better. I'll only be living in the area a year or two. I do have an old satellite TV antenna if that can be used to direct the signal.

  Read the article

• Remove Duplicate Second Unity Launcher on Dual Screen

  - by Eugene van der Merwe

  See attached image. On my dual screen display I have a Unity Launcher on the left hand screen and also on the right hand screen. Both work perfectly fine. I don't want two Unity Launchers. Every time I move my house to the right hand side it gets slowed down over the right launcher hampering my productivity. I have an Nvidia card with the Nvidia driver and I am using TwinView. Could somebody please tell me how to remove this extra duplicated launcher?

  Read the article

• no back light on my acer aspire 5734z

  - by Dave

  I installed Ubuntu (12.04) on my acer aspire 5734z and the back light stopped working. I have tried the fix by editing the grub file posted on here a couple of days ago but that hasn't fixed it. I have also looked for hardware drivers but that didn't get me anywhere. When I hook up an external monitor it works fine but i have been unsuccessful getting the laptop display to light up. Thanks edit removed link I found a fix here " http://crunchbanglinux.org/forums/post/66562/#p66562 " if anyone has a better fix than the one in that post, let me know.

  Read the article

• Upgraded to 11.10 lost personal folders, Ubuntu one shows no files

  - by Kevin

  Upgraded to 11.04, from 10.10 system would only come up in terminal mode, but it told me that an additional upgrade was available and did I want to do that. Foolishly thinking that might fix the problem, I said yes. This time it did not make it all the way through the upgrade, when I came back to the computer over an hour later, the screen was filled with an error message "could not open display", had to reboot. Went to recovery mode on reboot to install nvidia module, when I rebooted system came up fine, but without carrying over my personal folders, I have the home folder, but no personal named folder in it. Came to Ubuntu One, but gives error message; File Sync error. (org.freedesktop.DBus.Error.NoReply: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked Is the a way around this in order to restore my files? I know my files existed on Ubuntu one as of a few months ago.

  Read the article

< Previous Page | 378 379 380 381 382 383 384 385 386 387 388 389  | Next Page >