Search Results

Search found 18488 results on 740 pages for 'android networking'.

Page 383/740 | < Previous Page | 379 380 381 382 383 384 385 386 387 388 389 390  | Next Page >

  • MBPro, mid 2010 can't see Dlink DIR655 signal after sleep etc

    - by user88114
    This is my son's MBP 7,1 running Snow Leopard 10.6.7. Router signal is fine since iPad, Wintel on same table 20 feet from router are fine. the MBP however frequently wakes and fails to find the internet. iStumbler can see 1 neighbours hub and my garden hub are there but can't get to the normal DIR655 wifi... no ping no en0 or en1 device seems to exist. Airport off and on does not help. He just resets router and it all works but this does not please me! I must admit the winter sometimes seems to loose connect too, but less so. The DIR655 (hardware rev A3) is on the original EU firmware 1.10, I'm cautious about jumping to latest 1.31EU since no downgrade seems to be possible and that feels a bit risky as so much is set up and working fine. If I use the DIR655 admin web and release the lease the MBP has then wake it all worked OK. So I suspect lease timing/locking issue but unsure how to check up, plus why iStumbler seems to say the network is not visible at all when I sit on the iPad right next to it just fine.. I do not think there are any channel overlaps and we also have RFquiet DECT phones (Orchid) that are silent until lifted or called. Anyway signals all show low interference and high throughput except for this failure to connect. Just walked the MBP to the garden office and iStumbler now sees the more distant DIR655 signal although it will not connect to it (does not show under Sys Prefs NetNetwork names) even after airport off & on... It also refuses to connect to my garden network (an old Belkin acting as AP wired to DIR655), the signal it can see and even net name in Sys Prefs NetNetwork names (2 mins later):NOW both names ARE visible, but both fail to accept the correct WPA2 password and keep asking again after failing to connect. IT ALL MAKES NO SENSE TO ME. Just revoked the lease for the MBP on DIR655 and no changes although this seemed to help MBP wake into connection 1 hour ago. OK a bit of walking about to report. Carried MBP across garden towards DIR655, a few other wifis show up on iStumbler, low signals all channel 1. Right next to DIR655 but iStumbler not showing it, although most other wifi's have gone. I'd say iStubler is suffering timeouts&hangs but hard to be sure. Lots of attempts to Airport on/off, join other etc and suddenly I get to connect, get given new IP (I revoked), can browse. Walk away, connection drops quite soon at 30 feet then reconnected briefly then died again. MUST ATTEND ELSEWHERE FOR A BIT...

    Read the article

  • Generate a limited amount of random network traffic between 2 hosts

    - by Andrew S
    I'm trying to find a utility that will allow me to generate a constant flow of random network traffic at a specified rate between 2 hosts. The utility needs to run on Windows and OSX. I've tried iperf but it seems to be more oriented toward short-term testing/statistics and it really taxes the CPU even at slower rates. I want something that will generate traffic for a few weeks at say 10Mbps while I use other tools to monitor the impact of that level of traffic on the network.

    Read the article

  • NTOP gives warnings on startup

    - by FR6
    I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

    Read the article

  • How to bypass vpn talking to VMWare Guest?

    - by marc esher
    Greetings. Network/VPN n00b question here. I'm running VMWare Workstation with a Guest Windows 2003 Server. It has SQL Server 2000 installed. The sole purpose for this Guest is to house SQL Server... it needn't have internet access or access to any other resources on the network other than the host. When launch Check Point VPN software, the host routes through the company network before it connects to the guest ... i.e. it's no longer a direct connection. I assume this is just how things are supposed to work. However, what's happening is that the connection between my host and the SQL Server instance on the guest intermittently drops. It's not consistent, and some databases on the server will be responsive while others aren't. It appears that the databases with the most traffic on the guest (the ones I'm hitting with load tests) are the ones that become intermittently unresponsive. This problem only manifests when VPN is on; when it's off, I can pound away on this database with no troubles. Thanks for any advice!

    Read the article

  • Watching Netflix through a VPN

    - by Sergio
    Recently I bought a VPS from DigitalOcean. I setup a PPTP VPN so I could watch us Netflix content from outside the US. Now that I have it setup and all my traffic is going through the VPN, Netflix is still showing my home country content. Pandora is working, and when I search my IP it shows im in NY, so I guess traffic is being routed correctly. I have also tried to delete flash settings and cookies from browser. Any ideas on what could be happening?

    Read the article

  • Windows XP does not list WPA wireless networks

    - by Tomalak
    What can be the reason that Windows XP does not show WPA-encrypted wireless networks? The laptop I have problems with is an older model (Toshiba Satellite Pro 6100) with Windows XP SP3 on it, fresh install. The wireless network card in it is an Agere product that lists as "Toshiba Wireless LAN Mini PCI Card". The networks showed up perfectly before I first tried to connect to one (it was set to WPA2). The connection failed (the card supports WPA only), then something must have happend and Windows hides these networks now. A manually configured WPA setup via Windows' own wizard works, I'm using it right now. The network just won't show up in the list of available network on its own. I suspect that XP incorrectly set a flag somewhere that this network card does not support WPA. Is there such a flag, and if so, how can I change it back?

    Read the article

  • TTL and traceroute showing different values for same domain

    - by Cray XT3
    y am i getting two different output for tracert and ping. Ping Result showing total hops of 20 and tracert showing 8. default ttl value on my linux machine 64,icmp echo reply ttl value 44. 64-44=20 but tracert is showing only 8 hops. What can be the reason? If tracert is implemented using ttl then why am i getting different values for same domain.no matter how many times i tried. Fo google and google services,ttl value and tracrt are same,but for other domains its different.

    Read the article

  • Is there a simple way to detect ISP port blocking?

    - by Will M
    Is there a way to tell the difference between my ISP blocking traffic on certain ports and my NAT router/firewall blocking that traffic? The sites “Shields Up” and “Can you see me” show my ports closed or not accessible, but I assume that is primarily due to the NAT router. (Obviously, I could just remove the router, connect directly and use those sites, but is there a simple way to test without doing that?)

    Read the article

  • How to play WAV file through Network Paging Interface

    - by BGM
    In our building we have a Viking Paging ZPI-4 Interface for our intercom. The interface receives data from our Asterisk Phone system via a Cisco SPA112 Port Adapter which has it's own IP address on the network and converts digital into analog. Asterisk plays the "5" tone and then allows the user's voice to commence over the connection. Now, what I want to do is to play a wav file over this Viking Paging device using the Cisco Port Adapter. I know how to get Asterisk to do it, but I want to do this without Asterisk. I want some kind of program that can talk to the Cisco Port Adapter and then transmit the wav file into the Viking Paging Device. What kind of program do I need to get or make? Now, I found this link if it helps anyone with ideas. I also found this information, but I'm not sure how to apply it. I also found this, but it involves an arduino. However, I already have the analog-to-digital convertor, and the Viking will handle sending sound over the paging speakers. I just need to know how to send the wav file to the Viking via the Port Adapter. So far, I know my wav file should be formatted as 8bit mono, and I need to send the "5" tone to open the Viking Pager's channel. [update] I am trying to figure out if I can use VLC player to stream to the ipaddress of the Port Adapter. So far I'm not having success with that, and don't even know if it will work. Windows Media Player has a streaming option too. I am thinking that since the Cisco Port Adapter thinks it is a sort of phone, that the only way this can be done is via SIP.

    Read the article

  • setting up my own name server

    - by mmokh
    I'm in the process of setting up my own name servers using BIND9, however I want to visualize the name server setup in relation to registrars and other name servers. Say I have a domain www.mydomain.com I setup my 2 name servers: ns1.mydomain.com - 192.168.0.1 ns2.mydomain.com - 192.168.0.2 1) How does the world know that my name servers are now at ns1.mydomain and ns2.mydomain. I read about setting up glue records at my registrar. Could you please elaborate on this, i.e. once i setup these glue records, can I now use my name servers in NS records for any other domain? For e.g. NS records for www.otherdomain.com - ns1.mydomain.com/ns2.mydomain.com 2) Given I setup the glue records as mentioned above, do I "have to" update mydomain.com NS records to point to my name servers? Can I keep mydomain.com NS records pointing to my registrars name servers, however use ns1.mydomain.com/ns2.mydomain.com as name servers for any other domain I own? Thanks

    Read the article

  • Windows 7 Automatically Connecting To Unsecured Wireless Networks On Startup

    - by Xtend
    Most of the questions on this topic related to folks connecting to somebody else's wireless network when their own was available and could remedy the situation by going to their connections and unchecking the "connect automatically" box. See this: " Avoid automatically connecting to wireless network on windows 7 " as an example. In my situation, I've noticed that Win 7 will automatically connect to any unsecured wifi network - even if I have never connected to it in the past. If I am traveling and boot Win 7, it will start and connect to what appears to be the best signaled unsecured network without prompting me for confirmation (note: in the above link, "Naveen" seems to have same problem). Obviously, that is a security concern to me. Further, when I open "Network and Sharing" and "Manage wireless networks" the network is not displayed (probably because I labelled it a public network). Again, these are new, never connected with before, wireless networks. I always promptly disconnect from them but don't want to have to be on constant guard for an auto connection to a malicious network. This began about a month ago, as I recall, Win 7 did not behave like this in the past, I didn't monkey with wifi settings, and don't use a 3rd party connection manager. I did have to download some internet security certificates for army website access but I don't think that should mess with network settings. Any ideas how I can tell Win7 cease automatically connecting to networks or, at least, to prompt me for a confirmation before connecting?

    Read the article

  • Why does my Intel Tolapai network chip not transmit packets?

    - by Hanno Fietz
    I'm trying to deploy an embedded system (NISE 110 by Nexcom) based on the Intel EP80579 (Tolapai) chip. Tolapai apparently integrates controllers for Ethernet etc. on a single chip (Intel homepage). The machine can't get a network connection. Diagnosis as far as I could manage: Drivers drivers from Intel compiled and installed without problems (version 1.0.3-144). Kernel version and Linux distribution (CentOS 5.2, 2.6.18) match the driver's installation instructions. drivers are loaded and show up in lsmod (module names are gcu and iegbe) interfaces eth0 and eth1 show up in ifconfig ifconfig I can bring up the interfaces with fixed IP pinging the interface locally works ifconfig shows flag UP but not RUNNING Link ethtool shows "Link detected: no", "Speed: unknown (65536)" and "Duplex: unknown (255)" Link LED is on on the other side of the cable, ethtool shows "Link detected: yes" and reports a speed of 1000 Mbps, which has allegedly been auto-neogotiated with the problematic device. Network traffic analysis the device does not reply on ARP, ICMP echo or anything else (iptables is down) when trying to send ICMP or DHCP requests, they never reach the other end activity LED is off on the device, on at the other end. I tried the following without any effect: Different cables (2 straight, one crossed), I get the link LED lit up on each. Three different devices on the other end (one PC, one netbook, one router) Fixed ARP table entries on both sides Connecting both network ports of the machine with each other, won't ping through the cable, but will ping locally. Tried straight and crossed cables for that.

    Read the article

  • Load Balancing a UDP server

    - by Hellfrost
    Hello StackOverflow, I have a udp server, it is a central part in my business process. in order to handle the loads I'm expecting in the production environment I'll probably need 2 or 3 instances of the server. The server is almost entirely stateless, it mostly collects data, and the layer above it knows how to handle the minimal amount of stale data that can arise from the the multiple server instances. My question is, how can I implement load balancing between the servers? I would prefer to distribute the requests as evenly as possible between the servers. I would also would like to have some fidelity, I mean if client X was routed to server y, then I want all of X's subsequent requests to go to server Y, as long as it is sensible and not overloads Y. By the way it is a .NET system... what would you recommend?

    Read the article

  • Reserve internet connection.

    - by amouniverso
    I have the router D-link 804HV that have 20mbit\s internet via PPoE tunnel . It connect three PC with Windows Xp to my home net. One of three my PC have reserve stability wi-fi internet connection. How can I use the wi-fi connection as reserve if the router connection is not available? I try to set the Wi-fi PC as gate for the other two, but it's not working.

    Read the article

  • Windows doesn't get access to internet though linux easily does

    - by flashnik
    We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

    Read the article

  • Security of a free public VPN service

    - by Mark Belli
    I just started using VPNBOOK, which is a (very efficent) free VPN solution. I have a question: VPNBOOK user and pass used to connect to their vpn network are publicily available on their homepage; everybody uses them to connect to the vpn. Can a user intercept my wifi traffic and: Understand that my connections are directed to VPNBOOK servers. If point 1 is successful, then they could use VPNBOOK public user and pass to decrypt my traffic? I hope I am missing something, otherwise it would be a very big weakness and I would revert to a paid service (with a private account)

    Read the article

  • routing through multiple subinterfaces in debian

    - by Kstro21
    my question is as simple as the title, i have a debian 6 , 2 NICs, 3 different subnets in a single interface, just like this: auto eth0 iface eth0 inet static address 192.168.106.254 netmask 255.255.255.0 auto eth0:0 iface eth0:0 inet static address 172.19.221.81 netmask 255.255.255.248 auto eth0:1 iface eth0:1 inet static address 192.168.254.1 netmask 255.255.255.248 auto eth1 iface eth1 inet static address 172.19.216.3 netmask 255.255.255.0 gateway 172.19.216.13 eth0 is conected to a swith with 3 differents vlans, eth1 is conected to a router. No iptables DROP, so, all traffic is allowed. Now, passing the traffic through eth0 is OK, passing the traffic through eth0:0 is OK, but, passing the traffic through eth0:1 is not working, i can ping the ip address of that sub interface from a pc where this ip is the default gateway, but can't get to servers in the subnet of the eth1 interface, the traffic is not passing, even when i set the iptables to log all the traffic in the FORWARD chain and i can see the traffic there, but, the traffic is not really passing. And the funny is i can do any the other way around, i mean, passing from eth1 to eth0:1, RDP, telnet, ping, etc, doing some work with the iptable, i manage to pass some traffic from eth0:1 to eth1, the iptables look like this: iptables -t nat PREROUTING -d 192.168.254.1/32 -p tcp -m multiport --dports 25,110,5269 -j DNAT --to-destination 172.19.216.1 iptables -t nat PREROUTING -d 192.168.254.1/32 -p udp -m udp --dport 53 -j DNAT --to-destination 172.19.216.9 iptables -t nat PREROUTING -d 192.168.254.1/32 -p tcp -m tcp --dport 21 -j DNAT --to-destination 172.19.216.11 iptables -t nat POSTROUTING -s 172.19.216.0/24 -d 172.19.221.80/29 -j SNAT --to-source 172.19.221.81 iptables -t nat POSTROUTING -s 172.19.216.0/24 -d 192.168.254.0/29 -j SNAT --to-source 192.168.254.1 iptables -t nat POSTROUTING -s 172.19.216.0/24 -o eth0 -j SNAT --to-source 192.168.106.254 dong this is working, but,it is really a headache have to map each port with the server, imagine if i move the service from server, so, now i have doubts: can debian route through multiple subinterfaces?? exist a limit for this?? if not, what i'm doing wrong when i have the same setup with other subnets and it is working ok?? without the iptables rules in the nat, it doesn't work thanks and i hope good comments/answers

    Read the article

  • to measure throughput of testing device connect to server via AP

    - by samantha
    Description of project- I have a test tool to which DUT connects. The test tool has an access point in it and once DUT get connected to it via mac address we check RSSI and some other features of WiFi of DUT. Now I am wondering is there is any way I can measure throughput of Device under test via mac address of DUT from server side. Test-tool has LINUX fedora 11 in it and major coding is done in c/C++ and json command. Previously, I have tried to install ftp server on test-tool and DUT can connect to it and we can measure the throughput or data transfer rate, but this is not feasible solution as it requires lot of intervention from DUT. What I am interested in is 1) To run some script on server side /test tool and it gives me throughput of bandwidth of connected device may be via mac address of DUT OR 2) Server script transfer some files/packets to DUT and we can measure the throughput. Coding is not a major challenge at this stage , I just need some tool which requires minimum intervention from DUT.

    Read the article

  • Mounting any Windows share from OS X 10.7.5 suddenly stopped working

    - by user2169619
    I have problem with mounting Windows network shares from my OS X 10.7.5 - it worked but it stopped and nothing helps and nothing in logs. Here what I get when trying to mount it manually: mount -t smbfs //10.0.0.7/d /tmp/test When doing sniffing with tshark - no packet it sent through and I get immediately return from the command: mount_smbfs: server connection failed: Unknown error: -1 Nothing in /var/log/syslog.log and /var/log/kern.log. The Finder does not work either - it throws an error that something is wrong (in czech thus I'm not sending the message here). I just cannot connect to any network shares. In virtual Windows 7 in Parallels Desktop I can connect successfully, but not within the network share (so the Win7 is behind OS X NAT) but only with its own IP address. The Windows server share is on the same network segment connected through switch. Any advice how to debug and what can be wrong? I spent hours to find solution on Google and here but no-one with this kind of problem and I do not know how to further debug it since there is no meaningful log / trace etc. I can ping 10.0.0.7 and I can connect to FTP server on 10.0.0.7 - the Windows machine (XP) has firewall completely turned off. The problem is that with tshark, I'm not seeing any packet sending to 10.0.0.7 so it's not even trying to reach the server.

    Read the article

  • Sharing internet connection from Windows XP using wi-fi router

    - by Darius
    Hi, I have an network configuration like: Ethernet cable from ISP connected to Windows XP machine, configured with static IP 192.168.0.3 Another ethernet connection from 2nd Windows XP machine's network adapter to a Wi-Fi router (D-Link Airport G+) XP set to "Share internet connection", the 2nd adapter configured as static to 192.169.0.1 D-Link Airport Wi-Fi router also configured as "static connection", it's IP set to 192.169.0.2, default gateway set to 192.169.0.1. Network mask everywhere is 24. Laptop computer connected with the router with static IP 192.169.0.3 The problems are: XP machine sees the router (it's able to ping it and access it via the web admin tool) The router somehow cannot PING the XP machine (using the tool provided by the web-based admin tool) The laptop computer cannot ping anything and cannot be pinged The router is only accessible when the ethernet cable is connected with a router's 1-4 LAN port, when I connect it via "WAN" port (which I believe is the proper one) it's not visible from the XP machine If you have similar experience with configuring a network like this I would really appreciate your help. I cannot use the Wi-Fi router with the ISP cable itself.

    Read the article

  • Wirelss card not being detected in backtrack 5

    - by Jesse Nelson
    I just installed backtrack 5 and I am unable to detect my wireless card. iwconfig doesn't list my interface. I can see that the hardware is present in lspci -vnn (see below) but I can't get the interface detected. I have tried to reinstall the compat-wireless package but I get errors during the build (see below) I have done a ton of researching and I keep hitting a brick wall, mostly because the wiki for backtrack is down and I can't find any good resources. Does anyone know how to fix the issue? Also, does anyone no how I can scan the hardware to determine what NIC is assigning my interface? If I can figure out the interface name I think I can set it up manually by putting up the link and using wireless-tools to manually configure the connection, this is what I had to do in arch on my mac. As stated the wiki for backtrack is down and I can't find any help on the issue. I tried to do the full kernel upgrade suggested in my software update but after the update was complete and I logged back in I had a new log in manager and the only thing I was able to log into was window managers. However, after this update my wireless was working fine. Please help I am new to Linux and the wiki is down, I have nowhere else to turn. Forgot to mention I am using the KDE version, not Gnome. Thanks in advance for any help or support. Attempt at make: root@bt:/usr/src/compat-wireless-3.3-rc1-2# make /usr/src/compat-wireless-3.3-rc1-2/config.mk:254: "WARNING: CONFIG_CFG80211_WEXT will be deactivated or not working because kernel was compiled with CONFIG_WIRELESS_EXT=n. Tools using wext interface like iwconfig will not work. To activate it build your kernel e.g. with CONFIG_LIBIPW=m." make -C /lib/modules/2.6.38/build M=/usr/src/compat-wireless-3.3-rc1-2 modules make: *** /lib/modules/2.6.38/build: No such file or directory. Stop. make: *** [modules] Error 2 lspci output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn -i net lspci: I/O error at net, line 0 root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn 02:00.0 Network controller [0280]: Atheros Communications Inc. Device [168c:0032] (rev ff) (prog-if ff) !!! Unknown header type 7f ( This is the problem but I can't find the solution) Kernel modules: ath9k iwconfig output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# iwconfig lo no wireless extensions. eth0 no wireless extensions.

    Read the article

  • Intel PRO/1000 Server NIC on Windows latency. How to measure?

    - by Bobb
    Please note - this question is about latency of the card itself. Not latency of internet or anything else. Thank you for your attention on this matter. It is often said that good server NIC does make difference compared to low grade cards and on-board Ethernet chips. I understand that on-board chip will likely consume CPU time and stand-alone card would use its own chip. Also server card would be faster than low-grade card. Are these 2 facts explaining most of the server cards advantages over on-board and low-grade cards ethernet? How would you measure latency on the card itself? I saw some reports stating some microseconds figures of NIC latency but I dont see how to measure that... Any advise will be appreciated.

    Read the article

  • Authentication required by wireless network

    - by Roman
    I would like to use a wireless network from Ubuntu. In the network drop-down menu I select a network (this is a University network I have an account there). Then I get a windows with the following fields: Wireless Security: [WPA&WPA2 Enterprise] Authentication: [Tunneled TLS] Anonymous Identity: [] CA Certificate: [(None)] Inner Authentication: [some letters] User Name: [] Password: [] I put there my user name and password and do not change default value and leave "Anonymous Identity"blank. As a result of that I get "Authentication required by wireless network". How can I solve this problem? I think it is important to notice that our system administrator tried to find some files (which are probably needed to be used as "CA Certificate"). He said that he does not know where this file is located on Ubuntu (he support only Windows). So, probably this is direction I need to go. I need to find this file. But may be I am wrong. May be something else needs to be done. Could you pleas help me with that?

    Read the article

  • Is it better to use N WiFi or Cat5e ethernet for large file transfers?

    - by Seth
    I have a network containing 802.11 N WiFi Devices and gigabit ethernet devices, however using only Cat5e wiring. I know that if I used Cat6, the ethernet would be much faster however if I need to transfer a large file between a device thats connected normally connected via ethernet and a device thats normally connected via WiFi, would it be advantageous to bother plugging the WiFi device in to the network? or should I switch the ethernet device to WiFi? or does it really matter?

    Read the article

  • dd-wrt switch for PfSense

    - by Kmao
    I currently have eth2 on my pfsense set up, and configured as 192.168.1.1, it has dhcp setup with allocation being 192.168.1.10 - 192.168.1.245. On my dd-wrt box, i disabled the WAN, and set it to act as a port for the switch. I disabled dhcp, dnsmasq, spi firewall, Wlan0 and set a static IP for the router being 192.168.1.10 Pfsense is plugged into lan0 and pc plugged into lan1 (wan port is empty) I have followed a few different guides, but i can't seem to get my router to act as a switch. Anyone have success using DD-WRT as a switch while using pfsense as your dhcp/dns/gateway. Any advice would help :)

    Read the article

< Previous Page | 379 380 381 382 383 384 385 386 387 388 389 390  | Next Page >