Search Results

Search found 41561 results on 1663 pages for 'linux command'.

Page 399/1663 | < Previous Page | 395 396 397 398 399 400 401 402 403 404 405 406  | Next Page >

• How to create a software raid5 array without a spare

  - by Yannick M.

  I am trying to create a software raid5 array using mdadm: $ linux # mdadm --create --verbose /dev/md0 --level=5 --raid-devices=4 --spare-devices=0 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 mdadm: layout defaults to left-symmetric mdadm: chunk size defaults to 64K mdadm: array /dev/md0 started. However when inspecting /proc/mdstat Personalities : [raid6] [raid5] [raid4] md0 : active raid5 sdd1[4] sdc1[2] sdb1[1] sda1[0] 2930279808 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 0.3% (2970496/976759936) finish=186.1min speed=87172K/sec unused devices: <none> It seems one drive isn't active, so I check the details of the array: /dev/md0: Version : 00.90.03 Creation Time : Tue Jul 21 16:29:53 2009 Raid Level : raid5 Array Size : 2930279808 (2794.53 GiB 3000.61 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 4 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Jul 21 16:29:53 2009 State : clean, degraded, recovering Active Devices : 3 Working Devices : 4 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 64K Rebuild Status : 0% complete UUID : ce8b2f40:821d003c:0027688e:a70977ec Events : 0.1 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 2 8 33 2 active sync /dev/sdc1 4 8 49 3 spare rebuilding /dev/sdd1 And it seems there are only 3 active devices, with one spare. Is it just me, or something wrong here?

  Read the article

• Android webbrowser returns code 500 for webpage on Nginx webserver

  - by Paxxil

  Hey! I've come to a very weird behavior of a web browser on android mobile phone (I've tried HTC Wildfire and HTC Desire phones). I have a web server with Nginx v0.8.54. When i try to open a web page on the phone it shows me error: The requested item could not be loaded! (Status code: 500) BUT it only happens when I am requesting page through Mobile network. On Wifi it works just fine .... but there is more .... if I stop Nginx and start Apache web server it works just fine on both Mobile network and wifi. I've also tried other mobile network and it is the same behavior. Some server stats: Firewall is OFF Selinux is OFF the web page (using Nginx web server) opens normally on any other browser (IE, FF, Opera, Chrome, Safari) on the laptop or PC Nothing in nginx error.log This is the only entry in access.log when the page is requested: xxx.xxx.xxx.xxx - - [17/Mar/2011:11:19:49 -0500] 200 "GET / HTTP/1.1" 27405 "-" "Mozilla/5.0 (Linux; U; Android 2.2; en-gb; Desire_A8181 Build/FRF91) AppleWebKit/533.1 (KHTML, like Gecko) Version/4.0 Mobile Safari/533.1" "-" index.html has only "Hello World" string in it. There is no fishy javascript or anything else. .... but there is even more.... if i open the same page on another server, with the same Nginx build, with the same server and web server configuration.... it opens just fine. if anyone has any idea on what may be going on, i would really appreciate it if you let me know. Thanks! EDIT: i forgot to mention that page opens OK on Iphone and Nokia

  Read the article

• using a second computer as a mere screen/monitor in X (VNC?)

  - by lara michaels

  Hello My goal is to use three monitors with my Linux system. It is a laptop, so adding another video card is not the easiest solution. (I have investigated a number of such options: getting a docking station with a PCI slot, USB/Cardbus vga adapters, etc, and for the time being don't want to go that way.) I am wondering if using an older desktop+screen I have lying around as the third "monitor" might be the easiest solution, if only there is a way to get it to work as a seamless, integrated desktop. I was wondering if I can use VNC or perhaps X itself (?) to achieve the following: computer A is my main computer; it has all my files, etc. computer B is used just to display on an additional screen keyboard+mouse are connected to computer A use VNC or X to connect the two so that computer B shows a X screen that is just as if it was a third physical screen connected to computer A. I don't know if the last point is clear, but what I mean is that I would like to be able to: be able to have my window manager assign/move around virtual desktops on all three screens move windows back and forth between the screens attached to computer A and the screen of computer B be able to copy something in an app being shown on a screen of computer A and paste it into an app being shown on the screen attached to computer B access the filesystem on my main computer (A) when using applications that are being shown on the screen attached to computer B Basically, I would like X to treat computer B just like it was nothing but a third physical screen... Is this doable? : ) ~lara

  Read the article

• What program sent which packet to the network [closed]

  - by Erik Johansson

  I would like to have a tcpdump like program that shows which program sent a specific packet, instead of just getting the port number. This is a generic problem I've had on and off sometimes when you have and old tcpdump file lying around you have no way to find what program was sending that data.. The solution in how i can identify which process is making UDP traffic on linux ? is an indication that I can solve this with auditd, dTrace, OProfile or SystemTap, but doesn't show how to do it. I.e. it doesn't show the source port of the program calling bind().. The problem I had was strange UDP packets, and since those ports are so short lived it took me a while to solve this issue. I solved this by running an ugly hack similar to: while true; date +%s.%N;netstat -panut;done So either a method better than this hack, a replacement for tcpdump, or some way to get this info from the kernel so I can patch tcpdump. EDIT: This was asked on superuser "tracking what programs sends to net", no good solution though.

  Read the article

• Most scalable way of serving a small set of static HTTP content

  - by Ekevoo

  The story: Hi guys. I'm among the people responsible for serving the results of the most anticipated (by number of people participating) annual entrance exam in my state. As such, when our results are published, the interest is overwhelming. In the past we delegated the responsibility of serving the results to the media, but that spoils a little the officialness of these results. This year we went with a little (long overdue) experiment of using lighttpd instead of Apache as well as other physical network optimizations I wasn't directly involved with. The results were very satisfactory. The server didn't choke even once, nor we saw any of the usual Twitter complaints on unavailability and/or slowness that were previously common. However, because we still delegated the first publication of the results to the media I'm still not 100% sure we can handle the load of actually publishing the results first. The question: Now because these files are like 14MB in total and a true lightweight Linux distribution isn't that big either, I'm thinking: what if next year we run full RAMdrive? Is there any? Is that useful? Is that worth it for a team that uses Debian almost exclusively? Are there other optimizations that I should be focusing on instead?

  Read the article

• SQLSTATE[HY000]: General error: 2006 MySQL server has gone away

  - by Barkat Ullah

  Server details: RAM: 16GB HDD: 1000GB OS: Linux 2.6.32-220.7.1.el6.x86_64 Processor: 6 Core Please see the link below for my # top preview: I can often see the error mentioned in title in my plesk panel and my /etc/my.cnf configuration are as below: bind-address=127.0.0.1 local-infile=0 datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql max_connections=20000 max_user_connections=20000 key_buffer_size=512M join_buffer_size=4M read_buffer_size=4M read_rnd_buffer_size=512M sort_buffer_size=8M wait_timeout=300 interactive_timeout=300 connect_timeout=300 tmp_table_size=8M thread_concurrency=12 concurrent_insert=2 query_cache_limit=64M query_cache_size=128M query_cache_type=2 transaction_alloc_block_size=8192 max_allowed_packet=512M [mysqldump] quick max_allowed_packet=512M [myisamchk] key_buffer_size=128M sort_buffer_size=128M read_buffer_size=32M write_buffer_size=32M [mysqlhotcopy] interactive-timeout [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid open_files_limit=8192 As my server httpd conf is set to /etc/httpd/conf.d/swtune.conf and the configuration is as below: at prefork.c: <IfModule prefork.c> StartServers 8 MinSpareServers 10 MaxSpareServers 20 ServerLimit 1536 MaxClients 1536 MaxRequestsPerChild 4000 </IfModule> If I run grep -i maxclient /var/log/httpd/error_log then I can see everyday this error: [root@u16170254 ~]# grep -i maxclient /var/log/httpd/error_log [Sun Apr 15 07:26:03 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting [Mon Apr 16 06:09:22 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting I tried to explain everything that I changed to keep my server okay, but maximum time my server is down. Please help me which parameter can I change to keep my server okay and my sites can load fast. It is taking too much time to load my sites.

  Read the article

• Memeory Leak in Windows Page file when calling a shell command

  - by Arno

  I have an issue on our Windows 2003 x64 Build Server when invoking shell commands from a script. Each call causes a "memory leak" in the page file so it grows quite rapidly until it reaches the maximum and the machine stops working. I can reproduce the problem very nicely by running a perl script like for ($count=1; $count<5000; $count++) { system "echo huhu"; } It is independent of he scripting language as the same happens with lua: for i=1,5000 do os.execute("echo huhu") end I found somebody describing the same issue with php at http://www.issociate.de/board/post/454835/Memory_leak_occurs_when_exec%28%29_function_is_used_on_Windows_platform.html His solution: Firewall/Virus Scanner does not apply, neither are running on the machine. We can also reproduce the issue on other Developer Machines running XP 64, but not on XP 32 Bit. The guilty guy for the allocation is C:\WINDOWS\System32\svchost.exe -k netsvcs which runs all the basic Windows services. Does anybody know the issue and how to resolve it ?

  Read the article

• is ksplice production ready?

  - by faultyserver

  I would be interested to hear the serverfault community's experiences with Ksplice in production. Quick blurb from wikipedia: Ksplice is a free and open source extension of the Linux kernel which allows system administrators to apply security patches to a running kernel without having to reboot the operating system. and Ksplice can, without restarting the kernel, apply any source code patch that only needs to modify the kernel code. Unlike other hot update systems, Ksplice takes as input only a unified diff and the original kernel source code, and it updates the running kernel correctly, with no further human assistance required. Additionally, taking advantage of Ksplice does not require any preparation before the system is originally booted (the running kernel does not need to have been specially compiled, for example). In order to generate an update, Ksplice must determine what code within the kernel has been changed by the source code patch. So a few questions: How has the stability been? any odd issues that you have encountered with its 'rebootless live patching' of the kernel? Kernel panics or horror stories? I have been running it on a few test systems and so far its been working as advertised, but I am interested in what other sysadmins experiences have been with Ksplice before going 'all in' and deploying this on our production servers. So, anybody using Kspice in production? update: hmm, not seeing any real activity on this question after a couple of hours (besides some kind upvotes and favs). Maybe to spark some activity I'll also ask a few more questions and see if we can get this discussion going... "If you are aware of Ksplice, is there a reason you are not using it?" "Do you feel its still too bleeding edge, unproven or untested?" "Does Ksplice not fit well within your current patch-management system?" "Do you hate having systems that have long (and secure) uptimes?" ;-)

  Read the article

• Amazon EC2 instance missing Network Interface

  - by Sergiks

  I am running Linux on a t1.micro instance at Amazon EC2. Once I noticed bruteforce ssh login attemtps from a certain IP, after litle Googling I issued the two following commands (other ip): iptables -A INPUT -s 202.54.20.22 -j DROP iptables -A OUTPUT -d 202.54.20.22 -j DROP Either this, or maybe some other actions like yum upgrade perhaps, caused the follwing fiasco: after rebooting the server, it came up without the Network Interface! I only can connect to it through AWS Management Console JAVA ssh client - via local 10.x.x.x address. Console's Attach Network Interface as well as Detach.. are greyed out for this instance. Network Interfaces item at the left does not offer any Subnets to choose from, to create a new N.I. Please advice, how can I recreate a Network Interface for the instance? Upd. The instance is not accessible from outside: cannot be pinged, SSH'ed or connected by HTTP on port 80. Here's the ifconfig output: eth0 Link encap:Ethernet HWaddr 12:31:39:0A:5E:06 inet addr:10.211.93.240 Bcast:10.211.93.255 Mask:255.255.255.0 inet6 addr: fe80::1031:39ff:fe0a:5e06/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1426 errors:0 dropped:0 overruns:0 frame:0 TX packets:1371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:152085 (148.5 KiB) TX bytes:208852 (203.9 KiB) Interrupt:25 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) What is also unusual: a new micro instance I created from scratch, with no relation to the troubled one, was not pingable too.

  Read the article

• How to interrupt software raid resync?

  - by Adam5

  I want to interrupt a running resync operation on a debian squeeze software raid. (This is the regular scheduled compare resync. The raid array is still clean in such a case. Do not confuse this with a rebuild after a disk failed and was replaced.) How to stop this scheduled resync operation while it is running? Another raid array is "resync pending", because they all get checked on the same day (sunday night) one after another. I want a complete stop of this sunday night resyncing. [Edit: sudo kill -9 1010 doesn't stop it, 1010 is the PID of the md2_resync process] I would also like to know how I can control the intervals between resyncs and the remainig time till the next one. [Edit2: What I did now was to make the resync go very slow, so it does not disturb anymore: sudo sysctl -w dev.raid.speed_limit_max=1000 taken from http://www.cyberciti.biz/tips/linux-raid-increase-resync-rebuild-speed.html During the night I will set it back to a high value, so the resync can terminate. This workaround is fine for most situations, nonetheless it would be interesting to know if what I asked is possible. For example it does not seem to be possible to grow an array, while it is resyncing or resyncing "pending"]

  Read the article

• SSH connection problem - allowed from LAN but not WAN

  - by Kerem Ulutas

  I tried to setup my Arch Linux installation to be an SSH host, but here is the thing: I can ssh localhost, it fails to login via public key and asks for username and password, but still able to login. When I try ssh my_wan_ip it gives ssh_exchange_identification: Connection closed by remote host error. I've read all topics about this error and none helped me. By the way, just confirmed, it gives ssh: connect to host my_dyndns_hostname port 22: Connection refused from another machine (outside of my network, it has different wan ip). I have sshd: ALL in "hosts.allow", ALL:ALL in "hosts.deny". I am able to connect to my own pc via ssh, ping my own pc, but my ssh setup seems to be the problem, it gives that annoying error when I try to ssh from wan. /etc/ssh/ssh_config /etc/ssh/sshd_config And finally, here is the debug output for both sshd and ssh: (i ran ssh command and i took output to sshd debug after that): sshd debug ssh debug I can edit my question according to your needs. Just ask for any more information needed. BTW I have no iptables running. I have one cable dsl modem connected to a asus wl-330gE wireless access point, they both have their firewall disabled. I configured NAT so port 22 is directed to the pc I'm having this trouble. Any help appreciated, thanks..

  Read the article

• big cpu load on vmware server / linux

  - by dezfafara

  Hi, I currently using a server 2.x hosting 4 virtual machines on a linux system Today, on my physical server, I saw an enormous load average: this is the "top" of the server, illustrating my 4 virtual guests. top - 11:02:02 up 194 days, 23:09, 5 users, load average: 18.78, 12.05, 13.55 Tasks: 113 total, 4 running, 109 sleeping, 0 stopped, 0 zombie Cpu0 : 71.6%us, 19.0%sy, 0.0%ni, 8.8%id, 0.0%wa, 0.3%hi, 0.3%si, 0.0%st Cpu1 : 74.3%us, 10.4%sy, 0.0%ni, 15.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 72.5%us, 17.6%sy, 0.0%ni, 9.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 79.5%us, 4.6%sy, 0.0%ni, 16.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 8178884k total, 8129980k used, 48904k free, 134904k buffers Swap: 10490436k total, 148k used, 10490288k free, 6129728k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 7312 root 6 -10 1149m 921m 559m R 97 11.5 107947:09 vmware-vmx 6995 root 6 -10 779m 687m 317m R 92 8.6 107374:31 vmware-vmx 6693 root 6 -10 880m 659m 409m S 85 8.3 76947:33 vmware-vmx 12937 root 6 -10 960m 719m 523m S 75 9.0 67219:49 vmware-vmx In bold are the cpu usage for my 4 virtuals guests These guests are running on a linux system, and the appropriate process are usually 5% - 15% of cpu I don't understang why , since a few days I have this big problem. This is the "top" on a virtual guest which is at 95% of cpu load top - 11:23:15 up 194 days, 23:13, 4 users, load average: 0.25, 0.47, 0.59 Tasks: 92 total, 2 running, 90 sleeping, 0 stopped, 0 zombie Cpu(s): 1.4%us, 7.7%sy, 0.0%ni, 90.5%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 382296k total, 369732k used, 12564k free, 145156k buffers Swap: 979924k total, 13956k used, 965968k free, 86988k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3691 root 20 0 23948 1148 960 S 13.0 0.3 15339:23 vmware-guestd 3840 root 20 0 19880 584 512 S 7.7 0.2 1729:17 hald-addon-stor This virtual guest state is ok ... If anyone has any ideas .. Thanks

  Read the article

• Is Unix a PC Operating system?

  - by Corelgott

  I have got kind of a stupid question. I am doing my bachelor at a university. In a wirtten assigment a prof posted the task: "Name 3 PC-Operating Systems:" Well, I went on an included a variety of OS (Linux, Windows, Osx) including Unix & Solaris. Today I recieved a mail from my prof saying: "Unix is not a PC-Operating System. Many Unix-Variants are not PC-Hardware-Compatible (like AIX & HP-UX. About Solaris: there was one PC-Compatible version...)" I am kind of suprised: Even if may Unix-Variants are Power-PC and different bit-order – Those don't stop beeing PCs right now? The question was given in a written assigment! It was not a question that came up during lecture! Due to the original postest task being in German, I'll include it just to make sure, that nobody suspects an error in the translation... "Nennen Sie 3 PC-Betriebssysteme:" Response / Antwort: "Unix ist kein PC-Betriebssystem, viele Unix-Varianten sind nicht auf PC-Hardware lauffähig (AIX, HP-UX). Von Solaris gab es mal eine PC-Variante." Anybody got something on that? Thx & Cheers Corelgott

  Read the article

• iptables to block non-VPN-traffic if not through tun0

  - by dacrow

  I have a dedicated Webserver running Debian 6 and some Apache, Tomcat, Asterisk and Mail-stuff. Now we needed to add VPN support for a special program. We installed OpenVPN and registered with a VPN provider. The connection works well and we have a virtual tun0 interface for tunneling. To archive the goal for only tunneling a single program through VPN, we start the program with sudo -u username -g groupname command and added a iptables rule to mark all traffic coming from groupname iptables -t mangle -A OUTPUT -m owner --gid-owner groupname -j MARK --set-mark 42 Afterwards we tell iptables to to some SNAT and tell ip route to use special routing table for marked traffic packets. Problem: if the VPN failes, there is a chance that the special to-be-tunneled program communicates over the normal eth0 interface. Desired solution: All marked traffic should not be allowed to go directly through eth0, it has to go through tun0 first. I tried the following commands which didn't work: iptables -A OUTPUT -m owner --gid-owner groupname ! -o tun0 -j REJECT iptables -A OUTPUT -m owner --gid-owner groupname -o eth0 -j REJECT It might be the problem, that the above iptable-rules didn't work due to the fact, that the packets are first marked, then put into tun0 and then transmitted by eth0 while they are still marked.. I don't know how to de-mark them after in tun0 or to tell iptables, that all marked packet may pass eth0, if they where in tun0 before or if they going to the gateway of my VPN provider. Does someone has any idea to a solution? Some config infos: iptables -nL -v --line-numbers -t mangle Chain OUTPUT (policy ACCEPT 11M packets, 9798M bytes) num pkts bytes target prot opt in out source destination 1 591K 50M MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 MARK set 0x2a 2 82812 6938K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 CONNMARK save iptables -nL -v --line-numbers -t nat Chain POSTROUTING (policy ACCEPT 393 packets, 23908 bytes) num pkts bytes target prot opt in out source destination 1 15 1052 SNAT all -- * tun0 0.0.0.0/0 0.0.0.0/0 mark match 0x2a to:VPN_IP ip rule add from all fwmark 42 lookup 42 ip route show table 42 default via VPN_IP dev tun0

  Read the article

• Solr startup script problem

  - by Camran

  I have installed solr and it works finally... I have now problems setting it up to start automatically with a start command. I have followed a tutorial and created a file called solr in the /etc/init.d/solr dir... Here is that file: #!/bin/sh -e # SOLR auto-start # # description: auto-starts solr engine # processname: solr-production # pidfile: /var/run/solr-production.pid NAME="solr" PIDFILE="/var/run/solr-production.pid" LOG_FILE="/var/log/solr-production.log" SOLR_DIR="/etc/jetty" JAVA_OPTIONS="-Xmx1024m -DSTOP.PORT=8079 -DSTOP.KEY=stopkey -jar start.jar" JAVA="/usr/bin/java" start() { echo -n "Starting $NAME... " if [ -f $PIDFILE ]; then echo "is already running!" else cd $SOLR_DIR $JAVA $JAVA_OPTIONS 2> $LOG_FILE & sleep 2 echo `ps -ef | grep -v grep | grep java | awk '{print $2}'` > $PIDFILE echo "(Done)" fi return 0 } stop() { echo -n "Stopping $NAME... " if [ -f $PIDFILE ]; then cd $SOLR_DIR $JAVA $JAVA_OPTIONS --stop sleep 2 rm $PIDFILE echo "(Done)" else echo "can not stop, it is not running!" fi return 0 } case "$1" in start) start ;; stop) stop ;; restart) stop sleep 5 start ;; *) echo "Usage: $0 (start | stop | restart)" exit 1 ;; esac Whenever I do solr -start I get this error: "Error occurred during initialization of VM Could not reserve enough space for object heap" I think this is because of the file above... Also here is where I have solr installed: var/www/solr and here is the start.jar file located: var/www/start.jar Help me out if you know whats causing this. Thanks BTW: OS is ubuntu 9.10

  Read the article

• Multiple *NIX Accounts with Identical UID

  - by Tim

  I am curious whether there is a standard expected behavior and whether it is considered bad practice when creating more than one account on Linux/Unix that have the same UID. I've done some testing on RHEL5 with this and it behaved as I expected, but I don't know if I'm tempting fate using this trick. As an example, let's say I have two accounts with the same IDs: a1:$1$4zIl1:5000:5000::/home/a1:/bin/bash a2:$1$bmh92:5000:5000::/home/a2:/bin/bash What this means is: I can log in to each account using its own password. Files I create will have the same UID. Tools such as "ls -l" will list the UID as the first entry in the file (a1 in this case). I avoid any permissions or ownership problems between the two accounts because they are really the same user. I get login auditing for each account, so I have better granularity into tracking what is happening on the system. So my questions are: Is this ability designed or is it just the way it happens to work? Is this going to be consistent across *nix variants? Is this accepted practice? Are there unintended consequences to this practice? Note, the idea here is to use this for system accounts and not normal user accounts.

  Read the article

• Setting up SSL on JBoss 5

  - by socal_javaguy

  How can I enable SSL on JBoss 5 on a Linux (Red Hat - Fedora 8) box? What I've done so far is: (1) Create a test keystore. (2) Placed the newly generated server.keystore in $JBOSS_HOME/server/default/conf (3) Make the following change in the server.xml in $JBOSS_HOME/server/default/deploy/jbossweb.sar to include this: <!-- SSL/TLS Connector configuration using the admin devl guide keystore --> <Connector protocol="HTTP/1.1" SSLEnabled="true" port="8443" address="${jboss.bind.address}" scheme="https" secure="true" clientAuth="false" keystoreFile="${jboss.server.home.dir}/conf/server.keystore" keystorePass="mypassword" sslProtocol = "TLS" /> (4) The problem is that when JBoss starts it logs this exception (during start-up) (but I am still able to view everything under http://localhost:8080/): 03:59:54,780 ERROR [Http11Protocol] Error initializing endpoint java.io.IOException: Cannot recover key at org.apache.tomcat.util.net.jsse.JSSESocketFactory.init(JSSESocketFactory.java:456) at org.apache.tomcat.util.net.jsse.JSSESocketFactory.createSocket(JSSESocketFactory.java:139) at org.apache.tomcat.util.net.JIoEndpoint.init(JIoEndpoint.java:498) at org.apache.coyote.http11.Http11Protocol.init(Http11Protocol.java:175) at org.apache.catalina.connector.Connector.initialize(Connector.java:1029) at org.apache.catalina.core.StandardService.initialize(StandardService.java:683) at org.apache.catalina.core.StandardServer.initialize(StandardServer.java:821) at org.jboss.web.tomcat.service.deployers.TomcatService.startService(TomcatService.java:313) I do know that's there's more to be done to enable full SSL client authentication....

  Read the article

• Can I create a transparent command window in Windows

  - by dean20007

  In Ubuntu I can create a totally transparent terminal on my desktop Is there anyway I can achieve this in Windows??

  Read the article

• Whats the easiest route to trying out mono 2.6?

  - by E J

  We have several web applications built on Microsoft technologies (asp.net+mvc framework, built using VS2008, MS SQL Server). I have recently be playing with Ubuntu (9.10), installed using Wubi, and wanted to see if I can get our apps running on a foss software stack. I have got the hang of the very basics of Postgresql and I have read that there is some support for Linq to SQL in mono (as of 2.6) as well as asp.net/MVC. However I am unsure how to go about getting Mono 2.6 up and running. Here is what I have discovered so far: Ubuntu is not meant for the 'cutting edge' it is designed to be stable hence, it sometimes takes a release cycle or two for new software to make it to the repositories Mono is already installed by default, but it is likely to stay at version 2.4 for at least the 10.4 release You can install paralell environments of Mono, if you know what your doing. I have had a go at setting up parallel environments, but haven't had any luck yet. (And TBH I am not certain that that will do what I think it's gonna do). (tl;dr start here) Is there a distribution of Linux similar enough to Ubuntu, that I wouldn't have to start the learning curve all over again, but that will let me install Mono 2.6, Postgresql, (and possibly mono-develop 2.4)? Or should I persist with Ubuntu?

  Read the article

• How to re-add a RAID-10 failed drive on Ubuntu?

  - by thiesdiggity

  I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

  Read the article

• Problems with 5.1 digital out on Ubuntu 12.04

  - by user895319

  I've recently bought a new PC, installed Ubuntu and am now unable to get 5.1 digital sound working. Simple analogue stereo works fine on both the front and rear connectors. On my old box I connected the coax connection from my soundcard to my surround sound amplifier, set Settings-Sound to "Digital Stereo Duplex" and it worked. My old soundcard doesn't fit in my new machine so I'm using the built-in sound hardware. I'm connecting the combination output socket on the back of the PC via the same cable to my surround amp as before. The MB is an MSI Global H61M-P31 with an RealTek ALC887 sound chip. When I go to Settings-Sound I only see "Headphone Built-in Audio" and "Analogue Output Built-in Audio" - no digitial options. The output from aplay -l is: default Playback/recording through the PulseAudio sound server sysdefault:CARD=PCH HDA Intel PCH, ALC887-VD Analog Default Audio Device front:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Front speakers surround40:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers dmix:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample mixing device dsnoop:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample snooping device hw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct hardware device without any conversions plughw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Hardware device with all software conversions While googling for ALC887 I've seen some references to "ALC887 -VD Analog" and some to "ALC887 -VD Digital". Does anyone know if I need to force it to chance mode somehow? It's worth mentioning that when I set the output to 5.1 digital surround in Windows 7 on the same machine I still don't get any sound so it's not a unique Linux problem. Thanks for any help.

  Read the article

• Ubuntu - No gnome-panels, no right-click, no internet, no hotkeys

  - by Darthfett

  Hey guys, I've been using Ubuntu (Maverick 10.10) on my desktop (ATI Radeon 5830) for about 3 weeks now, but all of a sudden I am unable to even use my computer. As soon as I start up, I see my desktop, with icons, but I don't see any gnome-panels, and I'm unable to get any options if I right-click. I can start programs by double clicking them. I also cannot get an internet connection. I've tried restarting gnome-panel by killing it, using Ctrl+Alt+5 to switch to a terminal (I don't have a shortcut to one on my desktop, and no hotkeys will work), but no luck. Restarting my computer has no effect upon this (I have to manually cut the power, since I don't know the terminal command). As far as I know, I have not made any changes, and I've never had any problems in the past. This started when I was playing Minecraft, but my internet crapped out, and no amount of re-trying the connection would work. I know it was my computer, as my brother's was working fine in the other room. Any clues as to what's going on? I'm more than willing to troubleshoot.

  Read the article

• background jobs and ssh connections

  - by petrelharp

  This question has come up quite a lot (really a lot), but I'm finding the answers to be generally incomplete. The general question is "Why does/doesn't my job get killed when I exit/kill ssh?", and here's what I've found. The first question is: How general is the following information? The following seems to be true for modern Debian linux, but I am missing some bits; and what do others need to know? All child processes, backgrounded or not of a shell opened over an ssh connection are killed with SIGHUP when the ssh connection is closed only if the huponexit option is set: run shopt huponexit to see if this is true. If huponexit is true, then you can use nohup or disown to dissociate the process from the shell so it does not get killed when you exit. If huponexit is false, which is the default on at least some linuxes these days, then backgrounded jobs will not be killed on normal logout. But even if huponexit is false, then if the ssh connection gets killed, or drops (different than normal logout), then backgrounded processes will still get killed. This can be avoided by disown or nohup as in (2). There is some distinction between (a) processes whose parent process is the terminal and (b) processes that have stdin, stdout, or stderr connected to the terminal. I don't know what happens to processes that are (a) and not (b), or vice versa. Final question: How can I avoid behavior (3)? In other words, by default in Debian backgrounded processes run along merrily by themselves after logout but not after the ssh connection is killed. I'd like the same thing to happen to processes regardless of whether the connection was closed normally or killed. Or, is this a bad idea?

  Read the article

• Virtualizing an Inline network appliance with VirtualBox (or VMWare)

  - by Tzury Bar Yochay

  My device, which is a Linux based IP in-liner is transparent to the network peripherals, that is, no IP address assigned to any of its interfaces. For the sake of the conversation, let's use ADSL connection as an example, while the device is inspecting the bi-directional traffic, the network is behaving same as if device was not there, attached to the wire (see Physical setup at the attached diagram). I wonder if I can enclosed that "device" within a Windows machine and have it operated virtually so it still seats inline between the ADSL router and the Windows netwroking interface by using virtual NICs, (or whatever their name is in windows), and inspecting the traffic, same as if it was on a separate physical device, the drawing under "Virtual Setup" in the attached diagram show what I am trying to achieve. Reading a bit on the VirtualBox docs, seems like binding the right side is relatively simple, perhaps I should have one network adapter set as Bridge Networking and VirtualBox will connect it to the physical NIC on the host machine, and network packets are exchanged directly, circumventing the host operating system's network stack (WinXP in my case). However, I have no idea how to achieve the left side of my diagram, which requires adding virtual NICs to windows and configure them correctly in a way to make that pipeline possible. I would appreciate any help. by the way, if that is not possible with VirtualBox but with other virtualization solution (e.g. VMWare), I would accept the other as well.

  Read the article

• How to set up mysql storage for certain rsyslog input matches?

  - by ylluminate

  I'm draining various logs from Heroku to an rsyslog linux (ubuntu) server and am starting to have a little more to bite off than I can chew in terms of working with my log histories. I am needing to be able drill back in time based on more flexible details and more flexible access than what the standard syslog file(s) provide. I'm thinking that logging to mysql may be the correct approach, but how do I set this up such that it pulls only certain log entries into a table based on an identified? For example, I see a long hex string identifying each log entry from a certain Heroku app instance. I assume that I can just pipe those into the mysql socket vs ALL rsyslog input into mysql... Could someone please direct me to a resource that can walk me through the process of setting something like this up or simply provide some details that can help? I have 15+ years of Unix experience so I just need some nudging in the right direction as I've not really done a tremendous amount of work with syslog daemons previously in terms of pooling various servers into one. Additionally, I'd be interested in any log review tools that could make drilling through log arrangements like this more handy for developers.

  Read the article

< Previous Page | 395 396 397 398 399 400 401 402 403 404 405 406  | Next Page >