Search Results

Search found 32994 results on 1320 pages for 'second level cache'.

Page 404/1320 | < Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >

• Why does my PC successfully boot only when unplugged for more than a few minutes?

  - by philg

  I have an HP Pavilion Elite desktop computer, model HPE-490t. I like it because it didn’t cost too much, boots itself from an SSD, came with 16 GB of RAM, and has 6 CPU cores for editing video and camera RAW images. It has one behavioral quirk that I cannot explain, however. The recent power interruptions here in the Northeast got the machine into a state where it could not be restarted. It would power up for a second or two, shut down, and then power up again, never being able to get to the point of showing anything on the monitor. I unplugged it for about 10 seconds and plugged it back in. Same behavior (fails to boot). I unplugged it and walked away for an hour, then plugged it back in and it worked perfectly! I think something similar happened after installing a second hard disk drive into this machine. So the question is why does the computer behave differently depending on how long it has been unplugged? Where is energy stored that affects the machine’s ability to boot? Capacitors in the power supply? Battery on the motherboard (there is one for the clock, but that wouldn’t be exhausted by being unplugged for an hour, I don’t think)?

  Read the article

• Setting up ssh config file with id_rsa through tunnel

  - by Rubens

  I've been struggling to set up a valid configuration to open a connection with a second machine, passing through another one, and using an id_rsa (which requests me a password) to connect to the third machine. I've asked this question in another forum, but I've received no answer that could be considered very helpful. The problem, better described, goes as follows: Local machine: user1@localhost Intermediary machine: user1@inter Remote target: user2@final I'm able to do the entire connection using pseudo-tty: ssh -t inter ssh user2@final (this will ask me the password for the id_rsa file I have in machine "inter") However, for speeding things up, I'd like to set my .ssh/config file, so that I can simply connect to machine "final" using: ssh final What I've got so far -- which does not work -- is, in my .ssh/config file: Host inter User user1 HostName inter.com IdentityFile ~/.ssh/id_rsa Host final User user2 HostName final.com IdentityFile ~/.ssh/id_rsa_2 ProxyCommand ssh inter nc %h %p The id_rsa file is used to connect to the middle machine (this requires me no password typing), and id_rsa_2 file is used to connect to machine "final" (this one requests a password). I've tried mixing up some LocalForward and/or RemoteForward fields, and putting the id_rsa files in both first and second machines, but I could not seem to succeed with no configuration whatsoever. Hope somebody can help me here! Regards! P.S.: the thread I've tried to get some help from: http://www.linuxquestions.org/questions/linux-general-1/proxycommand-on-ssh-config-file-4175433750/

  Read the article

• MySQL getting stuck, eating up disk i/o

  - by bonez05

  Hi all, Using mySQL 5.0.51 on Solaris . At intermittent times it looks like MySQL is getting 'stuck' . The disk usage on the server spikes to 98% busy from reads. I used dtrace (specifically DTrace toolkit - iosnoop) to track down what processes was using all the reads. Mysql was calling tablename.TDM hundreds of times per second. There was no more than average load on the webserver that could account for this. There were no cronjobs running, and no other utilities like mysqldump or anything. It is a master / slave replication setup. As a jury-rigged fix, I altered the mysql table from 'tablename' to 'tablename2' and then back to 'tablename' This fixed the problem temporarily, and "unsticks" mysql. The disk usage goes back down and dtrace is no longer showing hundreds of reads to 'tablename.TDM' / second. A couple ideas I had are: 1. MySQL version bug 2. Infinite loop somewhere in my application (which i'm not sure how likely this is) 3. ?? Has anybody seen this before or have any insight? Thanks

  Read the article

• How to increase the speed between two external hard drives on my laptop?

  - by Roman

  Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

  Read the article

• How to increase the speed between two external hard drives on my laptop?

  - by Roman

  Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

  Read the article

• How to create a new background process in a KSH "while read" loop?

  - by yael

  The following test script has a problem. When I add the line (sleep 5 ) & in the script then the "while read" loop does not read all lines from the file, but only prints the first line. But when I remove the ( sleep 5 ) & from the script, then the script prints all lines as defined in the file. Why the ( sleep 5 ) & causes this? And how to solve the problem? I want to create a new process (for which the sleep is just an example) in the while loop: $ more test #!/bin/ksh while read -r line ; do echo Read a line: echo $line ( sleep 5 )& RESULT=$! echo Started background sleep with process id $RESULT sleep 1 echo Slept for a second kill $RESULT echo Killed background sleep with process id $RESULT done < file echo Completed On my Linux, when using the following contents of file: $ more file 123 aaa 234 bbb 556 ccc ...running ./test just gives me: Read a line: 123 aaa Started background sleep with process id 4181 Slept for a second Killed background sleep with process id 4181 Completed

  Read the article

• How does formatting works with a PowerShell function that returns a set of elements?

  - by Steve B

  If I write this small function : function Foo { Get-Process | % { $_ } } And if I run Foo It displays only a small subset of properties: PS C:\Users\Administrator> foo Handles NPM(K) PM(K) WS(K) VM(M) CPU(s) Id ProcessName ------- ------ ----- ----- ----- ------ -- ----------- 86 10 1680 412 31 0,02 5916 alg 136 10 2772 2356 78 0,06 3684 atieclxx 123 7 1780 1040 33 0,03 668 atiesrxx ... ... But even if only 8 columns are shown, there are plenty of other properties (as foo | gm is showing). What is causing this function to show only this 8 properties? I'm actually trying to build a similar function that is returning complex objects from a 3rd party .Net library. The library is flatting a 2 level hierarchy of objects : function Actual { $someDotnetObject.ACollectionProperty.ASecondLevelCollection | % { $_ } } This method is dumping the objects in a list form (one line per property). How can I control what is displayed, keeping the actual object available? I have tried this : function Actual { $someDotnetObject.ACollectionProperty.ASecondLevelCollection | % { $_ } | format-table Property1, Property2 } It shows in a console the expected table : Property1 Property2 --------- --------- ValA ValD ValB ValE ValC ValF But I lost my objects. Running Get-Member on the result shows : TypeName: Microsoft.PowerShell.Commands.Internal.Format.FormatStartData Name MemberType Definition ---- ---------- ---------- Equals Method bool Equals(System.Object obj) GetHashCode Method int GetHashCode() GetType Method type GetType() ToString Method string ToString() autosizeInfo Property Microsoft.PowerShell.Commands.Internal.Format.AutosizeInfo autosizeInfo {get;set;} ClassId2e4f51ef21dd47e99d3c952918aff9cd Property System.String ClassId2e4f51ef21dd47e99d3c952918aff9cd {get;} groupingEntry Property Microsoft.PowerShell.Commands.Internal.Format.GroupingEntry groupingEntry {get;set;} pageFooterEntry Property Microsoft.PowerShell.Commands.Internal.Format.PageFooterEntry pageFooterEntry {get;set;} pageHeaderEntry Property Microsoft.PowerShell.Commands.Internal.Format.PageHeaderEntry pageHeaderEntry {get;set;} shapeInfo Property Microsoft.PowerShell.Commands.Internal.Format.ShapeInfo shapeInfo {get;set;} TypeName: Microsoft.PowerShell.Commands.Internal.Format.GroupStartData Name MemberType Definition ---- ---------- ---------- Equals Method bool Equals(System.Object obj) GetHashCode Method int GetHashCode() GetType Method type GetType() ToString Method string ToString() ClassId2e4f51ef21dd47e99d3c952918aff9cd Property System.String ClassId2e4f51ef21dd47e99d3c952918aff9cd {get;} groupingEntry Property Microsoft.PowerShell.Commands.Internal.Format.GroupingEntry groupingEntry {get;set;} shapeInfo Property Microsoft.PowerShell.Commands.Internal.Format.ShapeInfo shapeInfo {get;set;} Instead of showing the 2nd level child object members. In this case, I can't pipe the result to functions waiting for this type of argument. How does Powershell is supposed to handle such scenario?

  Read the article

• Motherboard Dying? AHCI Drive Init and boot loop intermittent failure

  - by Adam Heath

  My computer is now intermittently failing to boot up. For the last couple of days, when I turn it on it hangs on "AHCI Drive Init...", and when powered off and on again, it booted up fine. Today, it did the same but failed in a few other ways too, seemingly at random: Hangs on "AHCI Drive Init..." Boot loop (after "AHCI Drive Init..." appears for a split second (no drives listed)) Black screen (after "AHCI Drive Init..." appears for a split second, a black screen with all fans still running) The interesting part is that the above is not affected by what drives are connected, or what to. I have tried both disks, each disk individually and no disks (along with trying the primary and secondary SATA controllers), none of this has any effect on what happens. After about 20+ attempts of different combinations, it suddenly decided it would boot up into Windows, and I hadn't touched anything for about 2 cycles. Motherboard: Gigabyte GA-870A-USB3 Processor: Amd Phoenom II x6 1090T RAM: 8GB Corsair 1600 Primary Disk: Plextor 128GB SSD Secondary Disk: Western Digital Black 1TB OS: Windows 8.1 Is this my motherboard dying? Or could something else be the cause? Thanks!

  Read the article

• How can I prevent firefox from using bitmap fonts at certain zoom levels?

  - by Ryan Thompson

  In firefox 3.6 on Ubuntu 9.10, certain sites seem to use bitmap fonts for any fixed-width fonts, but only at specific zoom levels. This site and other stackexchange sites are among the affected sites, and of course the default zoom level is affected. At unaffected zoom levels, I get the expected smooth curvy fonts. How can I make firefox use the nice curvy smooth fonts at all zoom levels?

  Read the article

• poor performance when deleteing many files

  - by choppy

  I've got two machines: The first is IBM Blade with 24 cores 96GB RAM and single local hard drive with 278GB divided to 4 partitions: 1. c: - 40GB; 3GB free 2. d: - 40GB; 37GB free 3. e: - 198322GB; 198.1 free 4. 100MB (EFI system Partition) Formatted with GPT The other is pizza server with 4 cores 8GB RAM and single local hard drive with 273GB divided to 3 partitions: 1. c: - 136.81; 20GB free 2. d: - 88.74GB; 87.91 free 3. e: - 47.85GB; 46.91 free Formatted with MBR I have two scripts, the first creates 20,000 files in one directory, each file size is 192KB, the second delete the folder (recursive) and prints how much time it toke to delete all files. The problem is on the first server (blade) it takes about 2 minutes to delete all 20,000 files while on the second (pizza) it takes about 4 seconds!? Both servers have clean windows server 2008R2 with no special application running on background. Any ideas what is going on?

  Read the article

• DPI Scaling in Windows 8.1 via command line

  - by Vulcan

  I'd like to create a keyboard shortcut to quickly and easily change the DPI scale on my machine. In Windows 8.1, the desktop display DPI scale can be set via the control panel (pictured below), taking effect immediately. Alternatively, the scale can be set manually in the registry, but doing so requires that the user sign in and out or restart the machine in order to take effect (and only works to imitate the "one scaling level for all my displays" option). How can I set the DPI scale via the command line, or otherwise programmatically?

  Read the article

• NGinx Domain name redirects

  - by Srikar

  Lets say I have a website named xyz.co, I also have other domain names with the same prefix like xyz.com, xyz.it, xyz.co.it Right now nginx works fine with server_name xyz.co in nginx.conf in port 80 I would want all the other domains to redirect to xyz.co also I would want www.* versions of the above to redirect to xyz.co. How can I get this? Is this nginx webserver level changes? or I need to make this changes in DNS?

  Read the article

• Move OS from RAID5 array to RAID 1 arrays

  - by Antoine

  I want to give a last boost to my old ProLiant ML350 G5 server which just needs to be reliable for a few more year only ! With a defined budget of about 1500$ (I do not have more), i plan to replace the CPU (+ adding a second one), the battery cache of my raid controller (E200i), double the RAM, and change all hard drives. I have 7 HDD (SAS 10krpm, 72Gb) + 1 spare in RAID5, and my system is all FULL (no empty tray, full disks). in my current RAID5 array, I have 2 partitions: - 1 OS partition, 20Gb - 1 data partition, 350 Gb I plan to replace these 8 disks with : - 2 x 300Gb SAS 15krpm in RAID 1 (= 1 partition for OS) - 2 x 2Tb SATA 7.2krpm in RAID 1 (= 1 partition for DATA) My biggest constraint is that I have only 01 day to upgrade my server. Therefore, I'm looking for cloning all my files (OS + data partition) to my new arrays, i.e : - the OS partition shall be cloned to the RAID1 "2x300Gb array" - the data partition shall be cloned to the RAID1 "2x2Tb array" My second problem is that I need to physically remove all the old hard drives before inserting the new ones. I'm running Windows Server 2003 R2, and even if MS support will expire soon, I cannot buy a new licence and spent time in configuration. Obviously, with 1500$, I cannot also buy a new server that I could start configuring from now ! Thought about ASR (NTBackup), but I have no floppy drive (and do not really want to invest in one !) Thought about a clonezilla clone, and read this interesting link : Windows Server 2003 - move C: partition to a new SAS disk , but i'm not so confident in using Clonezilla with RAID5. What should be the best option to quickly and easily (if possible!) "copy/paste" my OS (so no need to reinstall and reconfigure all) and DATA / programs / services, etc... ? Thanks for your comments

  Read the article

• What is the most secure way to allow a user read access to a log file?

  - by gAMBOOKa

  My application requires read access to /var/log/messages, which belongs to user and group root. What is the minimal exposure level required on /var/log/messages so my application can read it? Presently, my plan is to change the group ownership of /var/log/messages to a new group, and add root and my application user to it, but this would also give the application write privileges to /var/log/messages. OS: Centos 5.5

  Read the article

• Nginx: Forward all Subdomains

  - by mgutt

  My code doesn't work with second level tld's like domain.co.uk The strainge thing is, that it works in php with preg_match() ^^ Here is my conf: # add www. if ($host ~ ^(?!www)) { rewrite ^/(.*)$ http://www.$host/$1 permanent; } # remove subdomain if ($host ~ "^www\.(.*)\.(.*\.([a-z]{2,4}|[a-z]{2}\.[a-z]{2}))") { set $host_without_sub $2; rewrite ^/(.*)$ http://www.$host_without_sub/$1 permanent; }

  Read the article

• UNIX Question to b answered??? [closed]

  - by Nits

  Create a tree structure named ‘training’ in which there are 3 subdirectories – ‘level 1’,’ level2’ and ‘cep’. Each one is again further divided into 3. The ‘level 1’ is divided into ‘sdp’, ‘re’ and ‘se’. From the subdirectory ‘se’ how can one reach the home directory in one step and also how to navigate to the subdirectory ‘sdp’ in one step? Give the commands, which do the above actions? How will you copy a directory structure dir1 to dir2 ? (with all the subdirectories) How can you find out if you have the permission to send a message? Find the space occupied ( in Bytes) by the /home directory including all its subdirectories. What is the command for printing the current time in 24-hour format? What is the command for printing the year, month, and date with a horizontal tab between the fields? Create the following files: chapa, chapb, chapc, chapd, chape, chapA, chapB, chapC, chapD, chapE, chap01, chap02, chap03, chap04, chap05, chap11, chap12, chap13, chap14, and chap15. With reference to question 7, What is the command for listing all files ending in small letters? With reference to question 7, What is the command for listing all files ending in capitals? With reference to question 7, What is the command for listing all files whose last but one character is 0? With reference to question 7, What is the command for listing all files which end in small letters but not ‘a’ and ‘c’? In an organisation one wants to know how many programmers are there. The employee data is stored in a file called ‘personnel’ with one record per employee. Every record has field for designation. How can grep be used for this purpose? In the organisation mentioned in question 12 how can sed be used to print only the records of all employees who are programmers. In the organisation mentioned in question 12 how can sed be used to change the designation ‘programmer’ to ‘software professional’ every where in the ‘personnel’ file Find out about the sleep command and start five jobs in the background, each one sleeping for 10 minutes. How do you get the status of all the processes running on the system? i.e. using what option?

  Read the article

• My Reverse DNS PTR record seems to be right, but I'm still getting bouncing email

  - by johnbr

  Hello, I have a service (statusme.com) where I let people know (for example) that their kid's soccer games are cancelled because of bad weather. We send out emails to the people who have registered. I have a second server as a backup, (vps.statusme.com) and I've set up the application to send some of the email through the second server. But I'm getting complaints from various recipient SMTP servers that the email is considered spam. So I did some investigating, and it appears that they think my reverse DNS record isn't correct. But when I look at it via various rDNS websites and instructions I found elsewhere on ServerFault, everything looks correct: jb$ host -t a vps.statusme.com 8.8.8.8 Using domain server: Name: 8.8.8.8 Address: 8.8.8.8#53 Aliases: vps.statusme.com has address 66.84.8.246 jb$ host -t ptr 246.8.84.66.in-addr.arpa 8.8.8.8 Using domain server: Name: 8.8.8.8 Address: 8.8.8.8#53 Aliases: 246.8.84.66.in-addr.arpa domain name pointer vps.statusme.com. I'm confused about what I'm doing wrong. Thanks for any suggestions.

  Read the article

• Add Machine Key to machine.config in Load Balancing environment to multiple versions of .net framework

  - by davidb

  I have two web servers behind a F5 load balancer. Each web server has identical applications to the other. There was no issue until the config of the load balancer changed from source address persistence to least connections. Now in some applications I receieve this error Server Error in '/' Application. Validation of viewstate MAC failed. If this application is hosted by a Web Farm or cluster, ensure that configuration specifies the same validationKey and validation algorithm. AutoGenerate cannot be used in a cluster. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Web.HttpException: Validation of viewstate MAC failed. If this application is hosted by a Web Farm or cluster, ensure that configuration specifies the same validationKey and validation algorithm. AutoGenerate cannot be used in a cluster. Source Error: The source code that generated this unhandled exception can only be shown when compiled in debug mode. To enable this, please follow one of the below steps, then request the URL: Add a "Debug=true" directive at the top of the file that generated the error. Example: or: 2) Add the following section to the configuration file of your application: Note that this second technique will cause all files within a given application to be compiled in debug mode. The first technique will cause only that particular file to be compiled in debug mode. Important: Running applications in debug mode does incur a memory/performance overhead. You should make sure that an application has debugging disabled before deploying into production scenario. How do I add a machine key to the machine.config file? Do I do it at server level in IIS or at website/application level for each site? Does the validation and decryption keys have to be the same across both web servers or are they different? Should they be different for each machine.config version of .net? I cannot find any documentation of this scenario.

  Read the article

• Issues connecting to HP ProCurve switches

  - by BriGuy

  We are having a very strange issue trying to connect to our infrastructure switches via SSH. When you first try connecting to them, the switches will prompt for the password - and then just sit there after it is entered. If you create a second SSH session to the switch (while letting the first one remain open and just sitting there) it will let you log right in. The switches are doing the same thing with RADIUS and local authentication. The other strange part to all of this, is that about 10 switches started doing it all at the same time. As far as actual configuration of the switches, nothing has changed. Occasionally, one switch will start working like normal, but then stop again. These are all HP ProCurve managed switches, but all different models/firmware. Some switches that are not working are using the same firmware as others that are working. UPDATE: 20130312 I am also seeing this same behavior when trying to use telnet. The first telnet session just hangs there, and the second telnet session will let me log in. Rebooting the switches seems to get them working, but I still have 5 production switches that cannot easily be rebooted because of their production roles. Is anyone aware of anything else that can be switched on/off that may reset the logon for remote management or something like that?

  Read the article

• Doing arithmetic and passing it to the next command

  - by neurolysis

  I know how to do this in /bin/sh, but I'm struggling a bit in Windows. I know you can do arithmetic on 32-bit signed integers with SET /a 2+2 4 But how do I pass this to the next command? For example, the process I want to perform is as follows. Consumer editions of Windows have no native automated sleep function (I believe?) -- the best way to perform a sleep is to use PING in association with the -n switch to get that many seconds, minus one, of sleep. The following command is effective for a silent sleep: PING localhost -n 3 > NUL But I want to alias this into a sleep command. I'd like to have it elegant so that you enter the actual number of seconds you want to sleep after the command, right now I can do DOSKEY SLEEP=PING 127.0.0.1 -n $1 > NUL Which works, but it's always 1 second less than your input, so if you wanted to sleep for one second you would have to use the command SLEEP 2. That's not exactly ideal. Is there some way for me to pass the arithmetic of $1+1 and pass it on to the next command in Windows? I assume there is some way of using STDOUT...

  Read the article

• SQL 2008 R2 replication error: The process could not connect to Distributor

  - by Lance Lefebure

  I have two servers running SQL 2008 R2 Standard, each with an instance named "MAIN". I have a small test database on my primary server (one table, 13 rows) that I want to replicate to a second server as a proof-of-concept for some larger databases that I want to replicate. I set up the primary server to be a publisher and distributor, and set the database to do transactional replication. I copied the data to the second server via a backup/restore, not via a snapshot (which I'll have to do with the larger databases due to database size and limited bandwidth). I followed the instructions here: http://gnawgnu.blogspot.com/2009/11/sql-2008-transactional-replication-and.html Now on the subscriber, I go under Replication / Local Subscriptions / Right click / Properties on my subscription to the DB. The status of the last synchronization shows a status of: "The process could not connect to Distributor 'PRIMARYSERVER\MAIN'." Data IS replicating from the primary to the secondary. Any record I add on the primary shows up on the secondary server within seconds. Is the Distributor part of the Snapshot system that I'm not using, or is it part of the transaction replication stuff? Thanks, Lance

  Read the article

• Why do I need to set up Autologon values in registry twice before it works and can i fix this?

  - by jJack

  Background: As part an automated testing suite I am building, I need to set up Autologon on my virtual machines 'on demand'. By on demand, I mean that I don't want to necessarily pre-configure my VM or any snapshot to have Autologon set up already, for security reasons and also a huge business case. My solution so far: I'm copying a script to the guest machine and then using Sysinternals PsExec to execute it. The script is: reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v DefaultUserName /t REG_SZ /d myusername reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v DefaultPassword /t REG_SZ /d myfakepassword reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v DefaultDomainName /t REG_SZ /d mydomain reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v ForceAutoLogon /t REG_SZ /d 1 reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v AutoAdminLogon /t REG_SZ /d 1 reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon\AutoLogonChecked" /f /ve /d 1 Note: I don't believe AutoLogonChecked is required for machines post Windows 2000 but I'm doing it just in case for now. Maybe ForceAutoLogon isn't either, not sure yet. The Problem: I see PsExec executes this properly and all the values are in the registry, however when I restart the machine, the user isn't automatically logged on...When I run this a second time then restart the machine, the user is finally logged on. A diff between the registry states shows that the first time I run this, it is missing both the "1" for AutoAdminLogon, and also the DefaultPassword key. The second time I execute it, these values are correctly intact as I intended. So, what is going on here? Is this expected? This post claims in the end that it really all just works (the problem was that a logoff script was setting off the values). Doesn't seem to work for me however.

  Read the article

• What exactly is a Deamon ? ( how to run a root command from apache binded script that uses www-data user )?

  - by user224235

  I am trying to run this command from WSGI script service httpd restart The problem is this command can only be run by root and apache uses the www-data user. it has been said the solution is to use a Deamon Process i suppose the idea is to send the command to a file that will be executed by a script that is considered "root" user.. its difficult to understand why they would call this a Deamon Process and try to scare me. Perhaps it should have been called : proxy process when i got the idea that this was a proxy process.. i thought about adding a line to /var/spool/cron/root that way the cron would execute the command for me. but of course this means i have to get the system time and then add 1 second to it and then add it to that line so cron would execute the command for me as root but my script demands an output instantly. so i suppose i need to create a DEAMON PROCESS that works like the cron. in other words it is a bash file that will execute the command in a plain file.. but will this DEAMON PROCESS be running a while command 24/7 every second ? would that not waste resources ? it only needs to activate itself to check for a command to execute when there is a command to be executed. i mean in PHP and other programming languages.. running a while statement when there is nothing to be executed could waste resources of the server.. so why should a deamon process constantly be listening for anything. i only want it to listen and execute when it is needed. i do not need a process that is constantly listening.

  Read the article

• Set process priority to High: Dangerous?

  - by eek142

  I have read that setting something to realtime is a big no-no, so I am not going to do that. But I do have an application that I need to make sure always has the highest priority on my system as it is critical for the rest of the applications I am running. Is there any danger in setting the priority to high, which is one level below realtime? Also, how would I be able to do this by changing the shortcut target? What is the command?

  Read the article

• Weird glitches on Intel iGPU

  - by FrederikVds

  I have a weird problem that I can't manage to describe in one word, so I'm having trouble searching for a solution. My monitors sometimes go black for a tenth of a second. Other times, they show the image shifted a few centimeters to the left or to the right. This happens on both of my monitors, but not necessarily at the same time. I would say it happens about once a minute, unless under heavy load, in which case it can happen every second or so. Interestingly, heavy CPU/memory usage can also cause this, not just heavy GPU usage. This only happens when they are both at 1920x1080, not when one of them, or both, are at a lower resolution. It also happens when they are in mirrored mode instead of extended desktop mode. My GPU is obviously not at full clock speed most of the time: this happens at 350 MHz as well as at 1200 MHz. So it doesn't seem like a matter of too little performance. I'm not seeing any traditional artefacts, even when I use MSI Kombustor, only this kind of full-screen glitches. CPU stressing software isn't reporting any issues either. I'm thinking maybe the connection between my CPU and my PCH isn't fast enough, but I can't find anyone with the same problem to confirm that. I'd rather not invest in a discrete GPU without being certain it will fix something. Does anyone know how to search for this, or even better, does anyone have a solution? My full specs are below. Thanks in advance! Specs: ASUS P8Z77-M Intel Core i5-3570K (with Intel HD 4000 Graphics) 2x4 GB AMD Performance Edition memory Corsair Force 3 Series Rev. B 120GB SSD Maxtor 200GB HD Lite-On DVD-RW Antec 350 Watt PSU 64-bit Windows 7 Professional 2x Iiyama ProLite E2208HDS display

  Read the article

< Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >