Search Results

Search found 10812 results on 433 pages for 'boot partition'.

Page 426/433 | < Previous Page | 422 423 424 425 426 427 428 429 430 431 432 433  | Next Page >

• Wi-Fi Stick with ZD1211 chip refuses to work on Ubuntu >8.10. No clue.

  - by Benjamin Maus

  I have a machine running Ubuntu 9.10 (Karmic *x86_64*). Everything is running smooth so far, except for the Wi-Fi USB Stick. The same device worked perfectly in 8.10. The wireless device is a GW-US54GXS using the Zydas Zd1211 chipset. Dmesg output after plugging in: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' [ 196.304209] zd1211rw 2-1:1.0: phy0 [ 196.304227] usbcore: registered new interface driver zd1211rw [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Syslog output: Nov 5 11:20:24 somesystem kernel: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' Nov 5 11:20:24 kierkegaard NetworkManager: <info> Found radio killswitch rfkill0 (at /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/ieee80211/phy0/rfkill0) (driver <unknown>) Nov 5 11:20:24 somesystem kernel: [ 196.304209] zd1211rw 2-1:1.0: phy0 Nov 5 11:20:24 somesystem kernel: [ 196.304227] usbcore: registered new interface driver zd1211rw Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): new 802.11 WiFi device (driver: 'zd1211rw') Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/2 Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): now managed Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): device state change: 1 -> 2 (reason 2) Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): bringing up device. Nov 5 11:20:24 somesystem kernel: [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:24 somesystem kernel: [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 Nov 5 11:20:24 somesystem kernel: [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- Nov 5 11:20:24 somesystem NetworkManager: <WARN> nm_device_hw_bring_up(): (wlan0): device not up after timeout! Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): deactivating device (reason: 2). Nov 5 11:20:24 somesystem kernel: [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:29 somesystem wpa_supplicant[978]: Could not set interface 'wlan0' UP Nov 5 11:20:29 somesystem wpa_supplicant[978]: Failed to initialize driver interface Nov 5 11:20:29 somesystem NetworkManager: <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. Gnome tells me in the network menu that the device was "not ready". It appears in iwconfig but not in ifconfig. The same symptoms appear when I boot from the live CD. How can I solve this dilemma?

  Read the article

• ovs-vsctl: "eth0" is not a valid UUID

  - by Przemek Lach

  I'm trying to setup an open v-switch inside my Ubuntu 12.04 Server VM. I have created three interfaces for this VM and I want to create a port mirror inside of the VM using these there interfaces and open v-switch. There are three Host-Only Adapters: eth0, eth1, eth2. The idea is that three other VM's will be connected to these adapters. One of these VM's will stream UDP video to eth0 and I want the vswitch'd VM to mirror those packets from eth0 onto eth1 and eth2. Each of the VM's connected to eth1 and eth2 will get the same video stream. I performed the following steps to install open v-switch: $ apt-get install python-simplejson python-qt4 python-twisted-conch automake autoconf gcc uml-utilities libtool build-essential $ apt-get install build-essential autoconf automake pkg-config $ wget http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ tar xf http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ cd http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ apt-get install libssl-dev iproute tcpdump linux-headers-`uname -r` $ ./boot.sh $ ./configure - -with-linux=/lib/modules/`uname -r`/build $ make $ sudo make install After installation I configured as follows: $ insmod datapath/linux/openvswitch.ko $ sudo touch /usr/local/etc/ovs-vswitchd.conf $ mkdir -p /usr/local/etc/openvswitch $ ovsdb-tool create /usr/local/etc/openvswitch/conf.db Then I started the server: $ ovsdb-server /usr/local/etc/openvswitch/conf.db \ --remote=punix:/usr/local/var/run/openvswitch/db.sock \ --remote=db:Open_vSwitch,manager_options \ --private-key=db:SSL,private_key \ --certificate=db:SSL,certificate \ --bootstrap-ca-cert=db:SSL,ca_cert --pidfile --detach --log-file $ ovs-vsctl –no-wait init (run only once) $ ovs-vswitchd --pidfile --detach The above steps I got from this tutorial and it all worked fine. I then proceeded to add a port mirror based on the open v-switch documentation under Port Mirroring. I successfully completed the following commands: $ ovs-vsctl add-br br0 $ ovs-vsctl add-port br0 eth0 $ ovs-vsctl add-port br0 eth1 $ ovs-vsctl add-port br0 eth2 $ ifconfig eth0 promisc up $ ifconfig eth1 promisc up $ ifconfig eth2 promisc up At this point when I run ovs-vsctl show I get the following: 75bda8c2-b870-438b-9115-e36288ea1cd8 Bridge "br0" Port "br0" Interface "br0" type: internal Port "eth0" Interface "eth0" Port "eth2" Interface "eth2" Port "eth1" Interface "eth1" And when I run ifconfig I get the following: eth0 Link encap:Ethernet HWaddr 08:00:27:9f:51:ca inet6 addr: fe80::a00:27ff:fe9f:51ca/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth1 Link encap:Ethernet HWaddr 08:00:27:53:02:d4 inet6 addr: fe80::a00:27ff:fe53:2d4/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth2 Link encap:Ethernet HWaddr 08:00:27:cb:a5:93 inet6 addr: fe80::a00:27ff:fecb:a593/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth3 Link encap:Ethernet HWaddr 08:00:27:df:bb:d8 inet addr:192.168.1.139 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fedf:bbd8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2211 errors:0 dropped:0 overruns:0 frame:0 TX packets:1196 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:182987 (182.9 KB) TX bytes:125441 (125.4 KB) NOTE: I use eth3 as a bridge adapter for SSH'ing into the VM. So now, I think I've done everything correctly but when I try to create the bridge using the following command: $ ovs-vsctl -- set Bridge br0 mirrors=@m -- --id=@eth0 get Port eth0 -- --id=@eth1 get Port eth1 -- --id=@m create Mirror name=app1Mirror select-dst-port=eth0 select-src-port=@eth0 output-port=@eth1,eth2 I get the following error: ovs-vsctl: "eth0" is not a valid UUID I don't understand why it's not able to find the interfaces?

  Read the article

• Computer not POSTing "randomly"?

  - by smoth190

  I have a custom built PC that is exhibiting some...odd... behavior, something I've never seen before. It was working fine one day, and the next day, it wouldn't start. Seeing as I wanted an upgrade anyway, I purchased a new motherboard that was compatible with all my parts. While replacing the motherboard, I accidentally damaged the CPU. Well, I wanted a new one anyway... so I got a new one. Seeing as I was replacing a ton of parts already, I bought a new PSU because the old one was super loud. When I slapped it all together, it starts up, lights, fans, drives, they all start. But I get no display from the monitor. No beeps, which I believe means it doesn't POST. I figured it was the RAM, because after removing the sound card and graphics card, there was nothing else that I hadn't replaced. When I remove both sticks of RAM, I get a continuous beeping, and according to the mobo handbook, means no RAM. So I think the mobo is functional, or atleast partly. I bought new RAM, but it still didn't work. I tried 3 monitors, with both VGA and DIV. So it's probably not the monitor, either. Now, let me get to the random part. Every 20 or so boots (I should also mention, for about 3 out of 5 boots I have to unplug the PC because it won't powerdown via the button), it will POST and I'll get display. Then, after about 2 or 3 resets, it won't work again. This confuses me so much, because even when I change nothing, it will/will not work. My thought is that maybe it has something to do with the RAM not clearing or something. I also reset the CMOS battery, incase that had anything to do with it, but no eval. I found some weird suggestion online about holding the power button for 30 seconds while it was unplugged. That did nothing, but I didn't expect it would... I've replaced just about the entire computer, and all the parts are compatible. Done about everything I can think of, but nothing has worked. Hopefully someone can help me here. And as I side note: When I do get my computer to boot, it says my hardware has changed and I have to re-activate windows. But it says I have to call Microsoft to do it. So I get this fancy automated voice that asks me to enter in a code into windows, then it asks me "How many computers have you activated with this copy of Windows?". Well, I had it on my computer before I replaced everything, so I said 1. Then he yelled at me for violating my 1-use license. I dunno what's going on there, do I have to re-purchase Windows 7? And they wonder why people pirate software... That's just a bonus question, though. Specs: 8GB of DDR2 RAM (Corsair) AMD CPU (I don't know what GHz or model because I can't find the box... (I think its 4 cores of 2.8Ghz) ASRock A785GM-LE Motherboard

  Read the article

• Windows 7 disk errors after a few hours of runtime

  - by GFK

  I'm having trouble understanding what is going on with my work PC. Whenever I boot it, it runs fine for a while, then starts to randomly show disk errors. The displayed error often contains the message "not enough storage is available to process this command", although depending on the application that fails it can be different. This has happened for weeks now and is getting worse. This is what troubles me: It never seems to impact critical parts of the system (no BSOD, no freeze). Only some applications seem impacted, refusing to function correctly after a while: Outlook 2010 cannot download RSS feeds anymore, Firefox 6 or IE9 cannot download anything bigger than 3MB without failing, Windows Update fails, all msi installers fail, Visual Studio 2010 starts failing in weird manners... It only happens after a while using it (typically 3 hours, but it seems that installing a program or compiling several times makes it shorter) Rebooting solves it (temporarily). The system: The OS is Windows 7 Pro Spanish SP1, 32 bits The system is an HP Compaq 6000 Pro with 4 GB memory (only 3.4GB usable since the system is 32bit), one 500GB hard drive. Installed applications include: Visual Studio 2010, SQL Server 2008 R2, VMWare Workstation 7, Microsoft Security Essentials, Office 2010. Shutting down all related services and processes doesn't seem to change anything. The diagnostics I've run so far: Hard drive : 465GB, 165GB free Process Explorer : physical and virtual memory seem ok (pagefile is 5.3GB, physical memory usage 70%, system commit 39%) Windows Memory diagnostic tool: OK CHKDSK returned: 488282111 KB total disk space. 281668248 KB in 265779 files. 150188 KB in 62949 indexes. 0 KB in bad sectors. 571755 KB in use by the system. The log file has occupied 65536 kilobytes. 205891920 KB available on disk. For non-spanish speakers, that means all ok. SMART diagnostic tools (DiskCheckup) report all values normal. temperatures are in the normal range (HWinfo). The event viewer doesn't seem to contain any significant message. ran CCleaner 3, without any noticeable effect. I was thinking about some file number limit (between Visual Studio projects and other applications, there are around 300.000 files on the hard drive), but I couldn't find any. It's possible there is something related with the use of the temporary folders (it's the only explanation I have for why applications fail but Windows doesn't), but I cannot confirm that. Only thing I cannot find out is if chkdsk reporting 65MB for the log is normal. It seems since Vista it always reports this. Any other cleaning/diagnostic tool you might know of? Edit: I ran several other tools since I first published the question: Seagate SeaTools (the HD manufacturer's analysis tool): complete test run OK. Intel Rapid 10.1 (the HD controller manufacturer's troubleshooting tool): the HD's ok. Microsoft Desktop Heap Monitor: Desktop Heap Information Monitor Tool (Version 8.1.2925.0) Copyright (c) Microsoft Corporation. All rights reserved. Session ID: 1 Total Desktop: ( 46464 KB - 11 desktops) WinStation\Desktop Heap Size(KB) Used Rate(%) WinSta0\Winlogon (s1) 128 3.6 WinSta0\Disconnect (s1) 64 3.8 WinSta0\Default (s1) 20480 3.0 msswindowstation\mssrestricteddesk (s0) 1024 0.2 __X78B95_89_IW__A8D9S1_42_ID (s0) 1024 0.2 Service-0x0-3e5$\Default (s0) 1024 0.6 Service-0x0-3e4$\Default (s0) 1024 0.3 Service-0x0-3e7$\Default (s0) 1024 2.1 WinSta0\Winlogon (s0) 128 1.9 WinSta0\Disconnect (s0) 64 3.8 WinSta0\Default (s0) 20480 0.0 All ok, desktop heap usage < 5% Edit 2: I tried totally resetting my account by creating a new one, logging under this new one and delete the first one (local rights and files), then logging back with this deleted account (it is a domain account). No luck. Also, I found out often the error is "not enough storage is available to process this command". Searching on the internet, I found an old troubleshooting tip (setting a registry key to raise the IRP stack limit, whatever it is) which did not change anything.

  Read the article

• How do I make an external hard drive keep the same drive letter permanently?

  - by andygrunt

  I have a desktop PC (2002 vintage) running Windows XP that I turn on about 2 or 3 times per week. I have a mains powered 250Gb Western Digital hard disk connected to it via USB. I always turn the hard disk on before the PC so it's up and running as the PC boots. When I first connected the external hard disk, the PC assigned it a letter ('i' if it matters) and I've installed software to it, created shortcuts to various files and folders on the disk using that letter. For years everything was fine then I would boot the PC and the hard disk was assigned a different letter. I'd then have to go into 'my computer/manage/disk management' and manually change the letter back to 'i'. If I then rebooted the PC, the hard disk would usually still be 'i' but after the next reboot would be some other random letter and I have to manually change it back to 'i'. This would go on for some time then there'd be periods when the it would always be 'i' then, for no apparent reason (no new devices added, for example), the drive letter would start changing again. At the moment it's in random drive letter mood so I thought I'd ask the following question... How do I assign the external hard disk to be 'i' permanently? Answer: Thanks Molly that seems to have done the trick (after a little fiddling) - slightly disappointed there wasn't a way to do it within Windows without installing something else though. For anyone else trying this, it wasn't completely straightforward so here's what happened with me. I installed USBDLM as per the instructions on its website. I guessed that I had to assign the first USB letter to i so replaced the 'Letter1=' lines to 'Letter=I' in the ini file. To test it, I rebooted the PC only to find it came back up with the display set to 640x480 in 16 colours. After some investigation, I re-installed the display drivers and rebooted and set the display back to its usual setting. The external hard disk now gets set to 'i' but I found I had to re-apply sharing status to it so it was seen from my laptop which is on the same network. The end result of all this is that it now does what I wanted although it does act as though the hard drive has just been plugged in a few seconds after the Windows desktop appears i.e. the little box appears with a progress bar as it searches through the contents of the 'new' hard drive and I eventually get a dialogue box saying 'This disk or device contains more than one type of content. What do you want Windows to do?' and lists options such as play media files, print the pictures or open folder to view the files. This is a tiny pain I wish didn't happen but not exactly a huge price to pay. Other than that - it seems to work fine :) Looks like a spoke too soon... Every time I reboot, I have to re-share the 'i' drive (which I didn't have to do before) so it can be seen by my laptop on the same network. Any ideas how to make that permanent?

  Read the article

• "ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver" wheel-click is wrong

  - by sputnick

  I use this mouse under archlinux x86_64 with 3.2.8-1-ARCH kernel. I have some problems to select and then paste with the wheel-click in some applications like konversation, not in a terminal nor an editor. I don't know if it's a hardware problem or a software one. $ lsusb -v Bus 002 Device 110: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x046d Logitech, Inc. idProduct 0xc50e Cordless Mouse Receiver bcdDevice 25.10 iManufacturer 1 Logitech iProduct 2 USB RECEIVER iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 34 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 70mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 2 Mouse iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.11 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 95 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Device Status: 0x0000 (Bus Powered) When I see what's happens in xev, the output is different compared to another mouse My buggy Logitech mouse : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350700, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350700, (48,52), root:(1491,75), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 16 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350988, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350988, (48,52), root:(1491,75), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 a working mouse (dell) : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245131, (46,32), root:(1489,55), state 0x10, button 2, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245131, (46,32), root:(1489,55), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 528 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245411, (46,32), root:(1489,55), state 0x210, button 2, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245411, (46,32), root:(1489,55), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 A demo of the problem when I use konversation (IRC) : http://www.youtube.com/watch?v=lhmr92M7NCc I tried to modify the button map with xmodmap like this with no success (one at a time) : xmodmap -e "pointer = 1 0 3" xmodmap -e "pointer = 1 1 3" xmodmap -e "pointer = 1 2 3" xmodmap -e "pointer = 1 3 3" xmodmap -e "pointer = 1 4 3" xmodmap -e "pointer = 1 5 3" xmodmap -e "pointer = 1 6 3" xmodmap -e "pointer = 1 7 3" xmodmap -e "pointer = 1 8 3" xmodmap -e "pointer = 1 9 3" xmodmap -e "pointer = 1 10 3" xmodmap -e "pointer = 1 11 3" xmodmap -e "pointer = 1 12 3" xmodmap -e "pointer = 1 13 3" xmodmap -e "pointer = 1 14 3" xmodmap -e "pointer = 1 15 3" xmodmap -e "pointer = 1 16 3" xmodmap -e "pointer = 1 17 3" xmodmap -e "pointer = 1 18 3" xmodmap -e "pointer = 1 19 3" xmodmap -e "pointer = 1 20 3" xmodmap -e "pointer = 1 21 3" xmodmap -e "pointer = 1 22 3" xmodmap -e "pointer = 1 23 3" xmodmap -e "pointer = 1 24 3" xmodmap -e "pointer = 1 25 3" Any clue ? I would like to avoid buying a new mouse just for a paste problem.

  Read the article

• Add keyboard languages to XP, Vista, and Windows 7

  - by Matthew Guay

  Do you regularly need to type in multiple languages in Windows?  Here we’ll show you the easy way to add and change input languages to your keyboard in XP, Vista, and Windows 7. Windows Vista and 7 come preinstalled with support for viewing a wide variety of languages, so adding an input language is fairly simply.  Adding an input language is slightly more difficult in XP, and requires installing additional files if you need an Asian or Complex script language.  First we show how to add an input language in Windows Vista and 7; it’s basically the same in both versions.  Then, we show how to add a language to XP, and also how to add Complex Script support.  Please note that this is only for adding an input language, which will allow you to type in the language you select.  This does not change your user interface language. Change keyboard language in Windows 7 and Vista It is fairly simple to add or change a keyboard language in Windows 7 or Vista.  In Windows 7, enter “keyboard language” in the Start menu search box, and select “Change keyboards or other input methods”. In Windows Vista, open Control Panel and enter “input language” in the search box and select “Change keyboards or other input methods”.  This also works in Windows 7. Now, click Change Keyboards to add another keyboard language or change your default one. Our default input language is US English, and our default keyboard is the US keyboard layout.  Click Add to insert another input language while still leaving your default input language installed. Here we selected the standard Thai keyboard language (Thai Kedmanee), but you can select any language you want.  Windows offers almost any language you can imagine, so just look for the language you want, select it, and click Ok. Alternately, if you want, you can click Preview to see your layout choice before accepting it.  This is only the default characters, not ones that will be activated with Shift or other keys (many Asian languages use many more characters than English, and require the use of Shift and other keys to access them all).  Once your finished previewing, click close and then press Ok on the previous dialog. Now you will see both of your keyboard languages in the Installed services box.  You can click Add to go back and get more, or move your selected language up or down (to change its priority), or simply click Apply to add the new language. Also, you can now change the default input language from the top menu.  This is the language that your keyboard will start with when you boot your computer.  So, if you mainly use English but also use another language, usually it is best to leave English as your default input language. Once you’ve pressed Apply or Ok, you will see a new icon beside your system tray with the initials of your default input language. If you click it, you can switch between input languages.  Alternately you can switch input languages by pressing Alt+Shift on your keyboard. Some complex languages, such as Chinese, may have extra buttons to change input modes to accommodate their large alphabet. If you would like to change the keyboard shortcut for changing languages, go back to the Input Languages dialog, and select the “Advanced Key Settings” tab.  Here you can change settings for Caps Lock and change or add key sequences to change between languages. Also, the On-Screen keyboard will display the correct keyboard language (here the keyboard is displaying Thai), which can be a helpful reference if your physical keyboard doesn’t have your preferred input language printed on it.  To open this, simply enter “On-Screen keyboard” in the start menu search, or click All Programs>Accessories>On-Screen keyboard. Change keyboard language in Windows XP The process for changing the keyboard language in Windows XP is slightly different.  Open Control Panel, and select “Date, Time, Language, and Regional Options”.   Select “Add other languages”. Now, click Details to add another language.  XP does not include support for Asian and complex languages by default, so if you need to add one of those languages we have details for that below. Click Add to add an input language. Select your desired language from the list, and choose your desired keyboard layout if your language offers multiple layouts.  Here we selected Canadian French with the default layout. Now you will see both of your keyboard languages in the Installed services box.  You can click Add to go back and add more, or move your selected language up or down (to change its priority), or simply click Apply to add the new language. Once you’ve pressed Apply or Ok, you will see a new icon beside your system tray with the initials of your default input language. If you click it, you can switch between input languages.  Alternately you can switch input languages by pressing Alt+Shift on your keyboard. If you would like to change the keyboard shortcut for changing languages, go back to the Input Languages dialog, and click the “Key Settings” button on the bottom of the dialog.  Here you can change settings for Caps Lock and change or add key sequences to change between languages. Add support to XP for Asian and Complex script languages Windows XP does not include support for Asian and Complex script languages by default, but you can easily add them to your computer.  This is useful if you wish to type in one of these languages, or simply want to read text written in these languages, since XP will not display these languages correctly if they are not installed.  If you wish to install Chinese, Japanese, and/or Korean, check the “Install files for East Asian languages” box.  Or, if you need to install a complex script language (including Arabic, Armenian, Georgian, Hebrew, the Indic languages, Thai, and Vietnamese), check the “Install files for complex script and right-to-left languages” box.   Choosing either of these options will open a prompt reminding you that this option will take up more disk space.  Support for complex languages will require around 10Mb of hard drive space, but East Asian language support may require 230 Mb or more free disk space.  Click Ok, and click apply to install your language files. You may have to insert your XP CD into your CD drive to install these files.  Insert the disk, and then click Ok. Windows will automatically copy the files, including fonts for these languages… …and then will ask you to reboot your computer to finalize the settings.  Click Yes, and then reopen the “Add other languages” dialog when your computer is rebooted, and add a language as before.     Now you can add Complex and/or Asian languages to XP, just as above.  Here is the XP taskbar language selector with Thai installed. Conclusion Unfortunately we haven’t found a way to add Asian and complex languages in XP without having an XP disc. If you know of a way, let us know in the comments. (No downloading the XP disc from torrent site answers please) Adding an input language is very important for bilingual individuals, and can also be useful if you simply need to occasionally view Asian or Complex languages in XP.  And by following the correct instructions for your version of Windows, it should be very easy to add, change, and remove input languages. Similar Articles Productive Geek Tips Show Keyboard Shortcut Access Keys in Windows VistaKeyboard Ninja: 21 Keyboard Shortcut ArticlesAnother Desktop Cube for Windows XP/VistaThe "Up" Keyboard Shortcut for Windows 7 or Vista ExplorerWhat is ctfmon.exe And Why Is It Running? TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier Design Your Web Pages Using the Golden Ratio Worldwide Growth of the Internet How to Find Your Mac Address Use My TextTools to Edit and Organize Text

  Read the article

• Week in Geek: USDA Chooses Microsoft for Cloud Services Edition

  - by Asian Angel

  This week we learned how to create geeky LED holiday lights with old bottles, dig deeper in Windows Defrag via the command prompt, use Google Chrome’s drag/drop feature to upload files easier, find great gift recommendations by looking through the How-To Geek holiday gift guide, and have fun adding Merry Christmas fonts to our computers. Photo by ntr23. Random Geek Links It has been a busy week, so we have extra news link goodness with information that is good for you to know. USDA making the move to Microsoft The U.S. Department of Agriculture has announced that it has chosen Microsoft to host things like e-mail, instant messaging, and collaboration through the software giant’s Business Productivity Online Suite. Google says it was cut off from USDA project bid Google is claiming that it was not given a chance to bid on a cloud-computing project for the U.S. Department of Agriculture, for which the contract was awarded to rival Microsoft. Apache is being forced into a Java Fork When Oracle rolled over Apache and Google’s objections to its Java plans in December, the scene was set for Apache to leave and, eventually, force a Java code fork. Tumblr explains daylong outage After experiencing an outage that started on Sunday afternoon and stretched through most of the day yesterday, Tumblr has explained what happened. Google demos Chrome OS, launches pilot program During a press briefing this week in San Francisco, Google launched the Chrome application store and demonstrated Chrome OS, its browser-centric netbook operating system. Don’t expect Spotify in U.S. this holiday season As of last week, Spotify had yet to sign a single licensing deal with a major label, after spending more than a year negotiating, multiple music sources told CNET. December 2010 Patch Tuesday will come with most bulletins ever According to the Microsoft Security Response Center, Microsoft will issue 17 Security Bulletins addressing 40 vulnerabilities on Tuesday, December 14. It will also host a webcast to address customer questions the following day. Hacker plants back door in Symbian firmware Indian hacker Atul Alex has had a look at the firmware for Symbian S60 smartphones and come up with a back door for it. PC quarantines raise tough complexities The concept of quarantining PCs to prevent widespread infection is “interesting, but difficult to implement, with far too many problems”, said security experts. Symantec: DDoS attacks hard to defend It has surfaced that the distributed denial of service (DDoS) attacks on Visa and MasterCard Web sites on Wednesday were carried out by a toolkit known as low orbit ion cannon (LOIC). Web Sockets and the risks of unfinished standards Enthusiasm for a promising new standard called Web Sockets has quickly cooled in some quarters as a potential security problem led some browser makers to hastily postpone support. Internet Explorer 9 to get tracking protection Microsoft is making changes to Internet Explorer 9’s security features that will better enable users to keep sites from tracking their activity across browsing sessions. NASA sold PCs with sensitive data NASA failed to remove sensitive data from computers that it sold, according to an audit report released this week. Cybercrooks create fake Amazon receipts The bad guys have created yet another online scam, this one involving fake Amazon receipts. World of Warcraft character move fees waived Until December 22, Blizzard will allow free realm transfers from 25 highly populated servers to alleviate log-in queues or performance issues. (The free transfers are one-way and one-time only.) SpaceX Dragon reaches orbit atop a Falcon with a fiery tail The Space Exploration Technologies corporation has become the first nongovernmental entity to put a vehicle into low Earth orbit. Geek Video of the Week If birds have wings, then why are the Angry Birds using slingshots? Photo by Dorkly Bits. Wait… Birds have Wings, Why are the Angry Ones Using Slingshots? Sysadmin Geek Tips How To Setup Email Alerts on Linux Using Gmail or SMTP Linux machines may require administrative intervention in countless ways, but without manually logging into them how would you know about it? Here’s how to setup emails to get notified when your machines want some tender love and attention. Random TinyHacker Links Red Panda Webcam Support Firefox and the Knoxville Zoo’s Red Panda program. Christmas Icons (Icons we like) Superb set of holiday icons by lgp85 at deviantArt. Download the .zip and use as .png or convert to .ico at Convertico.com or with tiny app Imagicon. Super User Questions Enjoy reading the great answers to this week’s popular questions from Super User Useful USB boot disks? DVD/CD burning .zip: is it more reliable, faster, longer lasting to burn a zip of files rather than the files as a folder? What are other ways to backup my files if I do not have an external drive? Anti virus what is the difference between these all? How can I block all Facebook elements/content? How-To Geek Weekly Article Recap Have you had a busy week between work and preparing for the holidays? Get caught up on your HTG reading with our hottest articles of the week. 20 Windows Keyboard Shortcuts You Might Not Know The 50 Best Registry Hacks that Make Windows Better LCD? LED? Plasma? The How-To Geek Guide to HDTV Technology HTG Explains: Which Linux File System Should You Choose? How to Use and Customize Google Chrome Web Apps One Year Ago on How-To Geek This week’s batch of retro geeky goodness is all about customizing Windows 7. ClassicShell Adds Classic Start Menu and Explorer Features to Windows 7 Get an Aero-Styled Classic Start Menu in Windows 7 Customize the Windows 7 Logon Screen Get the Classic Style Network Activity Indicator Back in Windows 7 How To Enable Check Boxes for Items In Windows 7 The Geek Note We would like you to join us in welcoming Jason Fitzpatrick to the writing staff here at How-To Geek. He started with us this past week, so take some time to read through his articles about the Wii, Kindle, & PlayStation 2 Peripherals and leave a friendly comment to say “Hi”! Got a great tip to share? Make sure to send it in to us at [email protected]. Photo by real00. Latest Features How-To Geek ETC The 50 Best Registry Hacks that Make Windows Better The How-To Geek Holiday Gift Guide (Geeky Stuff We Like) LCD? LED? Plasma? The How-To Geek Guide to HDTV Technology The How-To Geek Guide to Learning Photoshop, Part 8: Filters Improve Digital Photography by Calibrating Your Monitor Our Favorite Tech: What We’re Thankful For at How-To Geek Settle into Orbit with the Voyage Theme for Chrome and Iron Awesome Safari Compass Icons Set Escape from the Exploding Planet Wallpaper Move Your Tumblr Blog to WordPress Pytask is an Easy to Use To-Do List Manager for Your Ubuntu System Snowy Christmas House Personas Theme for Firefox

  Read the article

• Week in Geek: LastPass Rescues Xmarks Edition

  - by Asian Angel

  This week we learned how to breathe new life into an aging Windows Mobile 6.x device, use filters in Photoshop, backup and move VirtualBox machines, use the BitDefender Rescue CD to clean an infected PC, and had fun setting up a pirates theme on our computers. Photo by _nash. Weekly Feature Do you love using the Faenza icon set on your Ubuntu system but feel that there are a few much needed icons missing (or you desire a different version of a particular icon)? Then you may want to take a look at the Faenza Variants icon pack. The icons are available in the following sizes: 16px, 22px, 32px, 48px and scalable sizes. Photo by Asian Angel. Faenza Variants Random Geek Links Another week with extra link goodness to help keep you on top of the news. Photo by Asian Angel. LastPass acquires Xmarks, premium service announced Xmarks announced that it has been acquired by LastPass, a cross-platform password management service. This also means that Xmarks is now in transition from a “free” to a “freemium” business model. WikiLeaks reappears on European Net domains WikiLeaks has re-emerged on a Swiss Internet domain followed by domains in Germany, Finland, and the Netherlands, sidestepping a move that had in effect taken the controversial site off the Internet. Iran: Yes, Stuxnet hurt our nuclear program The Stuxnet worm got some big play from Iranian President Mahmoud Ahmadinejad, who acknowledged that the malware dinged his nuclear program. More Windows Rogues than Just AV – Fake Defragmenter Check Disk Don’t think for a second that rogues are limited to scareware, because as so-called products such as “System Defragmenter”, “Scan Disk” “Check Disk” prove, they’re not. Internet Explorer’s Protected Mode can be bypassed Researchers from Verizon Business have now described a way of bypassing Protected Mode in IE 7 and 8 in order to gain access to user accounts. Can you really see who viewed your Facebook profile? Rogue application spreads virally Once again, a rogue application is spreading virally between Facebook users pretending to offer you a way of seeing who has viewed your profile. More holes in Palm’s WebOS Researchers Orlando Barrera and Daniel Herrera, who both work for security firm SecTheory, have discovered a gaping security hole in Palm’s WebOS smartphone operating system. Next-gen banking Trojans hit APAC With the proliferation of banking Trojans, Web and smartphone users of online banking services have to be on constant alert to avoid falling prey to fraud schemes, warned Etay Maor, project manager for RSA Fraud Action. AVG update cripples 64-bit computers A signature update automatically deployed by the AVG virus scanner Thursday has crippled numerous computers. Article includes link to forums to fix computers affected after a restart. Congress moves to outlaw ‘mystery charges’ for Web shoppers Legislation that makes it illegal for Web merchants and so-called post-transaction marketers to charge credit cards without the card owners’ say-so came closer to becoming law this week. Ballmer Set to “Look Into” Windows Home Server Drive Extender Fiasco Tuesday’s announcement from Microsoft regarding the removal of Drive Extender from Windows Home Server has sent shock waves across the web. Google tweaks search recipe to ding scam artists Google has changed its search algorithm to penalize sites deemed to provide an “extremely poor user experience” following a New York Times story on a merchant who justified abusive behavior towards customers as a search-engine optimization tactic. Geek Video of the Week Watch as our two friends debate back and forth about the early adoption of new technology through multiple time periods (Stone Age to the far future). Will our reluctant friend finally succumb to the temptation? Photo by CollegeHumor. Early Adopters Through History Random TinyHacker Links Fix Issues in Windows 7 Using Reliability Monitor Learn how to analyze Windows 7 errors and then fix them using the built-in reliability monitor. Learn About IE Tab Groups Tab groups is a useful feature in IE 8. Here’s a detailed guide to what it is all about. Google’s Book Helps You Learn About Browsers and Web A cool new online book by the Google Chrome team on browsers and the web. TrustPort Internet Security 2011 – Good Security from a Less Known Provider TrustPort is not exactly a well-known provider of security solutions. At least not in the consumer space. This review tests in detail their latest offering. How the World is Using Cell phones An infographic showing the shocking demographics of cell phone use. Super User Questions See the great answers to these questions from Super User. I am unable to access my C drive. It says it is unable to display current owner. List of Windows special directories/shortcuts like ‘%TEMP%’ Is using multiple passes for wiping a disk really necessary? How can I view two files side by side in Notepad++ Is there any tool that automatically puts screenshots to my Dropbox? How-To Geek Weekly Article Recap Look through our hottest articles from this past week at How-To Geek. How to Create a Software RAID Array in Windows 7 9 Alternatives for Windows Home Server’s Drive Extender Why Doesn’t Disk Cleanup Delete Everything from the Temp Folder? Ask the Readers: How Much Do You Customize Your Operating System? How to Upload Really Large Files to SkyDrive, Dropbox, or Email One Year Ago on How-To Geek Enjoy reading through these awesome articles from one year ago. How To Upgrade from Vista to Windows 7 Home Premium Edition How To Fix No Aero Transparency in Windows 7 Troubleshoot Startup Problems with Startup Repair Tool in Windows 7 & Vista Rename the Guest Account in Windows 7 for Enhanced Security Disable Error Reporting in XP, Vista, and Windows 7 The Geek Note That wraps things up here for this week. Regardless of the weather wherever you may be, we hope that you have an opportunity to get outside and have some fun! Remember to keep sending those great tips in to us at [email protected]. Photo by Tony the Misfit. Latest Features How-To Geek ETC The How-To Geek Guide to Learning Photoshop, Part 8: Filters Get the Complete Android Guide eBook for Only 99 Cents [Update: Expired] Improve Digital Photography by Calibrating Your Monitor The How-To Geek Guide to Learning Photoshop, Part 7: Design and Typography How to Choose What to Back Up on Your Linux Home Server How To Harmonize Your Dual-Boot Setup for Windows and Ubuntu Hang in There Scrat! – Ice Age Wallpaper How Do You Know When You’ve Passed Geek and Headed to Nerd? On The Tip – A Lamborghini Theme for Chrome and Iron What if Wile E. Coyote and the Road Runner were Human? [Video] Peaceful Winter Cabin Wallpaper Store Tabs for Later Viewing in Opera with Tab Vault

  Read the article

• Week in Geek: New Security Flaw Confirmed for Internet Explorer Edition

  - by Asian Angel

  This week we learned how to use a PC to stay entertained while traveling for the holidays, create quality photo prints with free software, share links between any browser and any smartphone, create perfect Christmas photos using How-To Geek’s 10 best how-to photo guides, and had fun decorating Firefox with a collection of Holiday 2010 Personas themes. Photo by Repoort. Random Geek Links Photo by Asian Angel. Critical 0-Day Flaw Affects All Internet Explorer Versions, Microsoft Warns Microsoft has confirmed a zero-day vulnerability affecting all supported versions of Internet Explorer, including IE8, IE7 and IE6. Note: Article contains link to Microsoft Security Advisory detailing two work-arounds until a security update is released. Hackers targeting human rights, indie media groups Hackers are increasingly hitting the Web sites of human rights and independent media groups in an attempt to silence them, says a new study released this week by Harvard University’s Berkman Center for Internet & Society. OpenBSD: audits give no indication of back doors So far, the analyses of OpenBSD’s crypto and IPSec code have not provided any indication that the system contains back doors for listening to encrypted VPN connections. But the developers have already found two bugs during their current audits. Sophos: Beware Facebook’s new facial-recognition feature Facebook’s new facial recognition software might result in undesirable photos of users being circulated online, warned a security expert, who urged users to keep abreast with the social network’s privacy settings to prevent the abovementioned scenario from becoming a reality. Microsoft withdraws flawed Outlook update Microsoft has withdrawn update KB2412171 for Outlook 2007, released last Patch Tuesday, after a number of user complaints. Skype: Millions still without service Skype was still working to right itself going into the holiday weekend from a major outage that began this past Wednesday. Mozilla improves sync setup and WebGL in Firefox 4 beta 8 Firefox 4.0 beta 8 brings better support for WebGL and introduces an improved setup process for Firefox Sync that simplifies the steps for configuring the synchronization service across multiple devices. Chrome OS the litmus test for cloud The success or failure of Google’s browser-oriented Chrome OS will be the litmus test to decide if the cloud is capable of addressing user needs for content and services, according to a new Ovum report released Monday. FCC Net neutrality rules reach mobile apps The Federal Communications Commission (FCC) finally released its long-expected regulations on Thursday and the related explanations total a whopping 194 pages. One new item that was not previously disclosed: mobile wireless providers can’t block “applications that compete with the provider’s” own voice or video telephony services. KDE and the Document Foundation join Open Invention Network The KDE e.V. and the Document Foundation (TDF) have both joined the Open Invention Network (OIN) as licensees, expanding the organization’s roster of supporters. Report: SEC looks into Hurd’s ousting from HP The scandal surrounding Mark Hurd’s departure from the world’s largest technology company in August has officially drawn attention from the U.S. Securities and Exchange Commission. Report: Google requests delay of new Google TVs Google TV is apparently encountering a bit of static that has resulted in a programming change. Geek Video of the Week This week we have a double dose of geeky video goodness for you with the original Mac vs PC video and the trailer for the sequel. Photo courtesy of Peacer. Mac vs PC Photo courtesy of Peacer. Mac vs PC 2 Trailer Random TinyHacker Links Awesome Tools To Extract Audio From Video Here’s a list of really useful, and free tools to rip audio from videos. Getting Your iPhone Out of Recovery Mode Is your iPhone stuck in recovery mode? This tutorial will help you get it out of that state. Google Shared Spaces Quickly create a shared space and collaborate with friends online. McAfee Internet Security 2011 – Upgrade not worthy of a version change McAfee has released their 2011 version of security products. And as this review details, the upgrades are minimal when compared to their 2010 products. For more information, check out the review. 200 Countries Plotted Hans Rosling’s famous lectures combine enormous quantities of public data with a sport’s commentator’s style to reveal the story of the world’s past, present and future development. Now he explores stats in a way he has never done before – using augmented reality animation. Super User Questions Enjoy looking through this week’s batch of popular questions and answers from Super User. How to restore windows 7 to a known working state every time it boots? Is there an easy way to mass-transfer all files between two computers? Coffee spilled inside computer, damaged hard drive Computer does not boot after ram upgrade Keyboard not detected when trying to install Ubuntu 10.10 How-To Geek Weekly Article Recap Have you had a super busy week while preparing for the holiday weekend? Then here is your chance to get caught up on your reading with our five hottest articles for the week. Ask How-To Geek: Rescuing an Infected PC, Installing Bloat-free iTunes, and Taming a Crazy Trackpad How to Use the Avira Rescue CD to Clean Your Infected PC Eight Geektacular Christmas Projects for Your Day Off VirtualBox 4.0 Rocks Extensions and a Simplified GUI Ask the Readers: How Many Monitors Do You Use with Your Computer? One Year Ago on How-To Geek Here are more great articles from one year ago for you to read and enjoy during the holiday break. Enjoy Distraction-Free Writing with WriteMonkey Shutter is a State of Art Screenshot Tool for Ubuntu Get Hex & RGB Color Codes the Easy Way Find User Scripts for Your Favorite Websites the Easy Way Access Your Unsorted Bookmarks the Easy Way (Firefox) The Geek Note That “wraps” things up for this week and we hope that everyone enjoys the rest of their holiday break! Found a great tip during the break? Then be sure to send it in to us at [email protected]. Photo by ArSiSa7. Latest Features How-To Geek ETC How to Use the Avira Rescue CD to Clean Your Infected PC The Complete List of iPad Tips, Tricks, and Tutorials Is Your Desktop Printer More Expensive Than Printing Services? 20 OS X Keyboard Shortcuts You Might Not Know HTG Explains: Which Linux File System Should You Choose? HTG Explains: Why Does Photo Paper Improve Print Quality? Simon’s Cat Explores the Christmas Tree! [Video] The Outdoor Lights Scene from National Lampoon’s Christmas Vacation [Video] The Famous Home Alone Pizza Delivery Scene [Classic Video] Chronicles of Narnia: The Voyage of the Dawn Treader Theme for Windows 7 Cardinal and Rabbit Sharing a Tree on a Cold Winter Morning Wallpaper An Alternate Star Wars Christmas Special [Video]

  Read the article

• usb mouse/keyboard doesn't work with 3.11.0-12-generic kernel

  - by x-yuri

  I can't use my usb keyboard/mouse after upgrade from raring to saucy. The keyboard works in grub menu and if I boot with the previous kernel version (3.8.0-31-generic). My new kernel version is 3.11.0-12-generic. I've got Mad Catz R.A.T.7 wired USB mouse, Canyon CNL-MBMSO02 wired usb mouse and Logitech diNovo Edge wireless keyboard, connected to computer through Logitech Unifying Receiver. Using PS/2 keyboard I've managed to get some information. dmesg says: [ 0.166273] ACPI: bus type USB registered [ 0.166273] usbcore: registered new interface driver usbfs [ 0.166273] usbcore: registered new interface driver hub [ 0.166273] usbcore: registered new device driver usb ... [ 3.534226] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.534228] ehci-pci: EHCI PCI platform driver [ 3.534291] ehci-pci 0000:00:1a.7: setting latency timer to 64 [ 3.534299] ehci-pci 0000:00:1a.7: EHCI Host Controller [ 3.534304] ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 3.534315] ehci-pci 0000:00:1a.7: debug port 1 [ 3.538218] ehci-pci 0000:00:1a.7: cache line size of 64 is not supported [ 3.538231] ehci-pci 0000:00:1a.7: irq 18, io mem 0xd3325400 [ 3.548017] ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 3.548042] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.548045] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.548048] usb usb1: Product: EHCI Host Controller [ 3.548050] usb usb1: Manufacturer: Linux 3.11.0-12-generic ehci_hcd [ 3.548053] usb usb1: SerialNumber: 0000:00:1a.7 [ 3.548155] hub 1-0:1.0: USB hub found [ 3.548159] hub 1-0:1.0: 6 ports detected [ 3.548311] ehci-pci 0000:00:1d.7: setting latency timer to 64 [ 3.548319] ehci-pci 0000:00:1d.7: EHCI Host Controller [ 3.548323] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 3.548333] ehci-pci 0000:00:1d.7: debug port 1 [ 3.552228] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported [ 3.552239] ehci-pci 0000:00:1d.7: irq 23, io mem 0xd3325000 [ 3.564014] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 3.564044] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.564047] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.564050] usb usb2: Product: EHCI Host Controller [ 3.564052] usb usb2: Manufacturer: Linux 3.11.0-12-generic ehci_hcd [ 3.564056] usb usb2: SerialNumber: 0000:00:1d.7 [ 3.564163] hub 2-0:1.0: USB hub found [ 3.564167] hub 2-0:1.0: 6 ports detected [ 3.564274] ehci-platform: EHCI generic platform driver [ 3.564280] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.564281] ohci-platform: OHCI generic platform driver [ 3.564287] uhci_hcd: USB Universal Host Controller Interface driver [ 3.564345] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 3.564347] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 3.564352] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 3.564378] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000f0c0 [ 3.564402] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.564404] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.564406] usb usb3: Product: UHCI Host Controller [ 3.564408] usb usb3: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.564410] usb usb3: SerialNumber: 0000:00:1a.0 [ 3.564478] hub 3-0:1.0: USB hub found [ 3.564482] hub 3-0:1.0: 2 ports detected [ 3.564589] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 3.564592] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 3.564597] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 3.564623] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000f0a0 [ 3.564647] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.564649] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.564651] usb usb4: Product: UHCI Host Controller [ 3.564653] usb usb4: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.564654] usb usb4: SerialNumber: 0000:00:1a.1 [ 3.564727] hub 4-0:1.0: USB hub found [ 3.564730] hub 4-0:1.0: 2 ports detected [ 3.564834] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 3.564837] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 3.564843] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 3.564863] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000f080 [ 3.564885] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.564887] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.564889] usb usb5: Product: UHCI Host Controller [ 3.564891] usb usb5: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.564892] usb usb5: SerialNumber: 0000:00:1a.2 [ 3.564962] hub 5-0:1.0: USB hub found [ 3.564966] hub 5-0:1.0: 2 ports detected [ 3.565073] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 3.565076] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 3.565081] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 3.565101] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000f060 [ 3.565124] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.565127] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.565128] usb usb6: Product: UHCI Host Controller [ 3.565130] usb usb6: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.565132] usb usb6: SerialNumber: 0000:00:1d.0 [ 3.565195] hub 6-0:1.0: USB hub found [ 3.565198] hub 6-0:1.0: 2 ports detected [ 3.565303] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 3.565306] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 3.565310] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 3.565329] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000f040 [ 3.565352] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.565354] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.565356] usb usb7: Product: UHCI Host Controller [ 3.565358] usb usb7: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.565359] usb usb7: SerialNumber: 0000:00:1d.1 [ 3.565424] hub 7-0:1.0: USB hub found [ 3.565427] hub 7-0:1.0: 2 ports detected [ 3.565534] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 3.565537] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 3.565541] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 3.565560] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000f020 [ 3.565584] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.565587] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.565588] usb usb8: Product: UHCI Host Controller [ 3.565590] usb usb8: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.565592] usb usb8: SerialNumber: 0000:00:1d.2 [ 3.565658] hub 8-0:1.0: USB hub found [ 3.565661] hub 8-0:1.0: 2 ports detected ... [ 4.120014] usb 2-3: new high-speed USB device number 2 using ehci-pci ... [ 4.468908] usb 2-3: New USB device found, idVendor=046d, idProduct=0825 [ 4.468912] usb 2-3: New USB device strings: Mfr=0, Product=0, SerialNumber=2 [ 4.468914] usb 2-3: SerialNumber: AF582E10 ... [ 5.284019] usb 5-2: new full-speed USB device number 2 using uhci_hcd [ 5.465903] usb 5-2: New USB device found, idVendor=046d, idProduct=0b04 [ 5.465908] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.465911] usb 5-2: Product: Logitech BT Mini-Receiver [ 5.465914] usb 5-2: Manufacturer: Logitech [ 5.468948] hub 5-2:1.0: USB hub found [ 5.470898] hub 5-2:1.0: 3 ports detected [ 5.476096] Switched to clocksource tsc [ 5.712099] usb 7-2: new full-speed USB device number 2 using uhci_hcd [ 5.896366] usb 7-2: New USB device found, idVendor=046d, idProduct=c52b [ 5.896370] usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.896372] usb 7-2: Product: USB Receiver [ 5.896374] usb 7-2: Manufacturer: Logitech [ 6.140016] usb 8-1: new full-speed USB device number 2 using uhci_hcd [ 6.324597] usb 8-1: New USB device found, idVendor=0738, idProduct=1708 [ 6.324603] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 6.324605] usb 8-1: Product: Mad Catz R.A.T.7 Mouse [ 6.324608] usb 8-1: Manufacturer: Mad Catz [ 6.564012] usb 8-2: new low-speed USB device number 3 using uhci_hcd [ 6.746602] usb 8-2: New USB device found, idVendor=1d57, idProduct=0010 [ 6.746608] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 6.746610] usb 8-2: Product: usb mouse with wheel [ 6.746613] usb 8-2: Manufacturer: HID-Compliant Mouse [ 7.337898] usb 5-2.2: new full-speed USB device number 3 using uhci_hcd [ 7.490902] usb 5-2.2: New USB device found, idVendor=046d, idProduct=c713 [ 7.490907] usb 5-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.490910] usb 5-2.2: Product: Logitech BT Mini-Receiver [ 7.490913] usb 5-2.2: Manufacturer: Logitech [ 7.490915] usb 5-2.2: SerialNumber: 001F203BD6A7 [ 7.569898] usb 5-2.3: new full-speed USB device number 4 using uhci_hcd [ 7.722901] usb 5-2.3: New USB device found, idVendor=046d, idProduct=c714 [ 7.722906] usb 5-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.722909] usb 5-2.3: Product: Logitech BT Mini-Receiver [ 7.722911] usb 5-2.3: Manufacturer: Logitech [ 7.722913] usb 5-2.3: SerialNumber: 001F203BD6A7 lsusb (more output): Bus 002 Device 002: ID 046d:0825 Logitech, Inc. Webcam C270 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 003: ID 1d57:0010 Xenta Bus 008 Device 002: ID 0738:1708 Mad Catz, Inc. Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 002: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 004: ID 046d:c714 Logitech, Inc. diNovo Edge Keyboard Bus 005 Device 003: ID 046d:c713 Logitech, Inc. Bus 005 Device 002: ID 046d:0b04 Logitech, Inc. Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub More background. Before that I had a problem with logging in to GNOME. During which I upgraded all the packages at one point (apt-get upgrade) and it stopped booting at all (it didn't get to login screen). Then I fixed PATH issue and now I've got this usb-not-working issue. I tried reinstalling kernel, to no effect. Is there anything else I can do to fix or diagnose the problem?

  Read the article

• JMS Step 7 - How to Write to an AQ JMS (Advanced Queueing JMS) Queue from a BPEL Process

  - by John-Brown.Evans

  JMS Step 7 - How to Write to an AQ JMS (Advanced Queueing JMS) Queue from a BPEL Process ol{margin:0;padding:0} .jblist{list-style-type:disc;margin:0;padding:0;padding-left:0pt;margin-left:36pt} .c4_7{vertical-align:top;width:468pt;border-style:solid;border-color:#000000;border-width:1pt;padding:5pt 5pt 5pt 5pt} .c3_7{vertical-align:top;width:234pt;border-style:solid;border-color:#000000;border-width:1pt;padding:0pt 5pt 0pt 5pt} .c6_7{vertical-align:top;width:156pt;border-style:solid;border-color:#000000;border-width:1pt;padding:5pt 5pt 5pt 5pt} .c16_7{background-color:#ffffff;padding:0pt 0pt 0pt 0pt} .c0_7{height:11pt;direction:ltr} .c9_7{color:#1155cc;text-decoration:underline} .c17_7{color:inherit;text-decoration:inherit} .c5_7{direction:ltr} .c18_7{background-color:#ffff00} .c2_7{background-color:#f3f3f3} .c14_7{height:0pt} .c8_7{text-indent:36pt} .c11_7{text-align:center} .c7_7{font-style:italic} .c1_7{font-family:"Courier New"} .c13_7{line-height:1.0} .c15_7{border-collapse:collapse} .c12_7{font-weight:bold} .c10_7{font-size:8pt} .title{padding-top:24pt;line-height:1.15;text-align:left;color:#000000;font-size:36pt;font-family:"Arial";font-weight:bold;padding-bottom:6pt} .subtitle{padding-top:18pt;line-height:1.15;text-align:left;color:#666666;font-style:italic;font-size:24pt;font-family:"Georgia";padding-bottom:4pt} li{color:#000000;font-size:10pt;font-family:"Arial"} p{color:#000000;font-size:10pt;margin:0;font-family:"Arial"} h1{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:24pt;font-family:"Arial";font-weight:normal} h2{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:18pt;font-family:"Arial";font-weight:normal} h3{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:14pt;font-family:"Arial";font-weight:normal} h4{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:12pt;font-family:"Arial";font-weight:normal} h5{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:11pt;font-family:"Arial";font-weight:normal} h6{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:10pt;font-family:"Arial";font-weight:normal} This post continues the series of JMS articles which demonstrate how to use JMS queues in a SOA context. The previous posts were: JMS Step 1 - How to Create a Simple JMS Queue in Weblogic Server 11g JMS Step 2 - Using the QueueSend.java Sample Program to Send a Message to a JMS Queue JMS Step 3 - Using the QueueReceive.java Sample Program to Read a Message from a JMS Queue JMS Step 4 - How to Create an 11g BPEL Process Which Writes a Message Based on an XML Schema to a JMS Queue JMS Step 5 - How to Create an 11g BPEL Process Which Reads a Message Based on an XML Schema from a JMS Queue JMS Step 6 - How to Set Up an AQ JMS (Advanced Queueing JMS) for SOA Purposes This example demonstrates how to write a simple message to an Oracle AQ via the the WebLogic AQ JMS functionality from a BPEL process and a JMS adapter. If you have not yet reviewed the previous posts, please do so first, especially the JMS Step 6 post, as this one references objects created there. 1. Recap and Prerequisites In the previous example, we created an Oracle Advanced Queue (AQ) and some related JMS objects in WebLogic Server to be able to access it via JMS. Here are the objects which were created and their names and JNDI names: Database Objects Name Type AQJMSUSER Database User MyQueueTable Advanced Queue (AQ) Table UserQueue Advanced Queue WebLogic Server Objects Object Name Type JNDI Name aqjmsuserDataSource Data Source jdbc/aqjmsuserDataSource AqJmsModule JMS System Module AqJmsForeignServer JMS Foreign Server AqJmsForeignServerConnectionFactory JMS Foreign Server Connection Factory AqJmsForeignServerConnectionFactory AqJmsForeignDestination AQ JMS Foreign Destination queue/USERQUEUE eis/aqjms/UserQueue Connection Pool eis/aqjms/UserQueue 2 . Create a BPEL Composite with a JMS Adapter Partner Link This step requires that you have a valid Application Server Connection defined in JDeveloper, pointing to the application server on which you created the JMS Queue and Connection Factory. You can create this connection in JDeveloper under the Application Server Navigator. Give it any name and be sure to test the connection before completing it. This sample will write a simple XML message to the AQ JMS queue via the JMS adapter, based on the following XSD file, which consists of a single string element: stringPayload.xsd <?xml version="1.0" encoding="windows-1252" ?> <xsd:schema xmlns:xsd="http://www.w3.org/2001/XMLSchema"                xmlns="http://www.example.org"                targetNamespace="http://www.example.org"                elementFormDefault="qualified">  <xsd:element name="exampleElement" type="xsd:string">  </xsd:element> </xsd:schema> The following steps are all executed in JDeveloper. The SOA project will be created inside a JDeveloper Application. If you do not already have an application to contain the project, you can create a new one via File > New > General > Generic Application. Give the application any name, for example JMSTests and, when prompted for a project name and type, call the project   JmsAdapterWriteAqJms  and select SOA as the project technology type. If you already have an application, continue below. Create a SOA Project Create a new project and select SOA Tier > SOA Project as its type. Name it JmsAdapterWriteAqJms . When prompted for the composite type, choose Composite With BPEL Process. When prompted for the BPEL Process, name it JmsAdapterWriteAqJms too and choose Synchronous BPEL Process as the template. This will create a composite with a BPEL process and an exposed SOAP service. Double-click the BPEL process to open and begin editing it. You should see a simple BPEL process with a Receive and Reply activity. As we created a default process without an XML schema, the input and output variables are simple strings. Create an XSD File An XSD file is required later to define the message format to be passed to the JMS adapter. In this step, we create a simple XSD file, containing a string variable and add it to the project. First select the xsd item in the left-hand navigation tree to ensure that the XSD file is created under that item. Select File > New > General > XML and choose XML Schema. Call it stringPayload.xsd  and when the editor opens, select the Source view. then replace the contents with the contents of the stringPayload.xsd example above and save the file. You should see it under the XSD item in the navigation tree. Create a JMS Adapter Partner Link We will create the JMS adapter as a service at the composite level. If it is not already open, double-click the composite.xml file in the navigator to open it. From the Component Palette, drag a JMS adapter over onto the right-hand swim lane, under External References. This will start the JMS Adapter Configuration Wizard. Use the following entries: Service Name: JmsAdapterWrite Oracle Enterprise Messaging Service (OEMS): Oracle Advanced Queueing AppServer Connection: Use an existing application server connection pointing to the WebLogic server on which the connection factory created earlier is located. You can use the “+” button to create a connection directly from the wizard, if you do not already have one. Adapter Interface > Interface: Define from operation and schema (specified later) Operation Type: Produce Message Operation Name: Produce_message Produce Operation Parameters Destination Name: Wait for the list to populate. (Only foreign servers are listed here, because Oracle Advanced Queuing was selected earlier, in step 3) .         Select the foreign server destination created earlier, AqJmsForeignDestination (queue) . This will automatically populate the Destination Name field with the name of the foreign destination, queue/USERQUEUE . JNDI Name: The JNDI name to use for the JMS connection. This is the JNDI name of the connection pool created in the WebLogic Server.JDeveloper does not verify the value entered here. If you enter a wrong value, the JMS adapter won’t find the queue and you will get an error message at runtime. In our example, this is the value eis/aqjms/UserQueue Messages URL: We will use the XSD file we created earlier, stringPayload.xsd to define the message format for the JMS adapter. Press the magnifying glass icon to search for schema files. Expand Project Schema Files > stringPayload.xsd and select exampleElement : string . Press Next and Finish, which will complete the JMS Adapter configuration. Wire the BPEL Component to the JMS Adapter In this step, we link the BPEL process/component to the JMS adapter. From the composite.xml editor, drag the right-arrow icon from the BPEL process to the JMS adapter’s in-arrow.   This completes the steps at the composite level. 3. Complete the BPEL Process Design Invoke the JMS Adapter Open the BPEL component by double-clicking it in the design view of the composite.xml. This will display the BPEL process in the design view. You should see the JmsAdapterWrite partner link under one of the two swim lanes. We want it in the right-hand swim lane. If JDeveloper displays it in the left-hand lane, right-click it and choose Display > Move To Opposite Swim Lane. An Invoke activity is required in order to invoke the JMS adapter. Drag an Invoke activity between the Receive and Reply activities. Drag the right-hand arrow from the Invoke activity to the JMS adapter partner link. This will open the Invoke editor. The correct default values are entered automatically and are fine for our purposes. We only need to define the input variable to use for the JMS adapter. By pressing the green “+” symbol, a variable of the correct type can be auto-generated, for example with the name Invoke1_Produce_Message_InputVariable. Press OK after creating the variable. Assign Variables Drag an Assign activity between the Receive and Invoke activities. We will simply copy the input variable to the JMS adapter and, for completion, so the process has an output to print, again to the process’s output variable. Double-click the Assign activity and create two Copy rules: for the first, drag Variables > inputVariable > payload > client:process > client:input_string to Invoke1_Produce_Message_InputVariable > body > ns2:exampleElement for the second, drag the same input variable to outputVariable > payload > client:processResponse > client:result This will create two copy rules, similar to the following: Press OK. This completes the BPEL and Composite design. 4. Compile and Deploy the Composite Compile the process by pressing the Make or Rebuild icons or by right-clicking the project name in the navigator and selecting Make... or Rebuild... If the compilation is successful, deploy it to the SOA server connection defined earlier. (Right-click the project name in the navigator, select Deploy to Application Server, choose the application server connection, choose the partition on the server (usually default) and press Finish. You should see the message ----  Deployment finished.  ---- in the Deployment frame, if the deployment was successful. 5. Test the Composite Execute a Test Instance In a browser, log in to the Enterprise Manager 11g Fusion Middleware Control (EM) for your SOA installation. Navigate to SOA > soa-infra (soa_server1) > default (or wherever you deployed your composite) and click on  JmsAdapterWriteAqJms [1.0] , then press the Test button. Enter any string into the text input field, for example “Test message from JmsAdapterWriteAqJms” then press Test Web Service. If the instance is successful, you should see the same text you entered in the Response payload frame. Monitor the Advanced Queue The test message will be written to the advanced queue created at the top of this sample. To confirm it, log in to the database as AQJMSUSER and query the MYQUEUETABLE database table. For example, from a shell window with SQL*Plus sqlplus aqjmsuser/aqjmsuser SQL> SELECT user_data FROM myqueuetable; which will display the message contents, for example Similarly, you can use the JDeveloper Database Navigator to view the contents. Use a database connection to the AQJMSUSER and in the navigator, expand Queues Tables and select MYQUEUETABLE. Select the Data tab and scroll to the USER_DATA column to view its contents. This concludes this example. The following post will be the last one in this series. In it, we will learn how to read the message we just wrote using a BPEL process and AQ JMS. Best regards John-Brown Evans Oracle Technology Proactive Support Delivery

  Read the article

• Solaris 11 Launch Blog Carnival Roundup

  - by constant

  Solaris 11 is here! And together with the official launch activities, a lot of Oracle and non-Oracle bloggers contributed helpful and informative blog articles to help your datacenter go to eleven. Here are some notable blog postings, sorted by category for your Solaris 11 blog-reading pleasure: Getting Started/Overview A lot of people speculated that the official launch of Solaris 11 would be on 11/11 (whatever way you want to turn it), but it actually happened two days earlier. Larry Wake himself offers 11 Reasons Why Oracle Solaris 11 11/11 Isn't Being Released on 11/11/11. Then, Larry goes on with a summary: Oracle Solaris 11: The First Cloud OS gives you a short and sweet rundown of what the major new features of Solaris 11 are. Jeff Victor has his own list of What's New in Oracle Solaris 11. A popular Solaris 11 meme is to write a blog post about 11 favourite features: Jim Laurent's 11 Reasons to Love Solaris 11, Darren Moffat's 11 Favourite Solaris 11 Features, Mike Gerdt's 11 of My Favourite Things! are just three examples of "11 Favourite Things..." type blog posts, I'm sure many more will follow... More official overview content for Solaris 11 is available from the Oracle Tech Network Solaris 11 Portal. Also, check out Rick Ramsey's blog post Solaris 11 Resources for System Administrators on the OTN Blog and his secret 5 Commands That Make Solaris Administration Easier post from the OTN Garage. (Automatic) Installation and the Image Packaging System (IPS) The brand new Image Packaging System (IPS) and the Automatic Installer (IPS), together with numerous other install/packaging/boot/patching features are among the most significant improvements in Solaris 11. But before installing, you may wonder whether Solaris 11 will support your particular set of hardware devices. Again, the OTN Garage comes to the rescue with Rick Ramsey's post How to Find Out Which Devices Are Supported By Solaris 11. Included is a useful guide to all the first steps to get your Solaris 11 system up and running. Tim Foster had a whole handful of blog posts lined up for the launch, teaching you everything you need to know about IPS but didn't dare to ask: The IPS System Repository, IPS Self-assembly - Part 1: Overlays and Part 2: Multiple Packages Delivering Configuration. Watch out for more IPS posts from Tim! If installing packages or upgrading your system from the net makes you uneasy, then you're not alone: Jim Laurent will tech you how Building a Solaris 11 Repository Without Network Connection will make your life easier. Many of you have already peeked into the future by installing Solaris 11 Express. If you're now wondering whether you can upgrade or whether a fresh install is necessary, then check out Alan Hargreaves's post Upgrading Solaris 11 Express b151a with support to Solaris 11. The trick is in upgrading your pkg(1M) first. Networking One of the first things to do after installing Solaris 11 (or any operating system for that matter), is to set it up for networking. Solaris 11 comes with the brand new "Network Auto-Magic" feature which can figure out everything by itself. For those cases where you want to exercise a little more control, Solaris 11 left a few people scratching their heads. Fortunately, Tschokko wrote up this cool blog post: Solaris 11 manual IPv4 & IPv6 configuration right after the launch ceremony. Thanks, Tschokko! And Milek points out a long awaited networking feature in Solaris 11 called Solaris 11 - hostmodel, which I know for a fact that many customers have looked forward to: How to "bind" a Solaris 11 system to a specific gateway for specific IP address it is using. Steffen Weiberle teaches us how to tune the Solaris 11 networking stack the proper way: ipadm(1M). No more fiddling with ndd(1M)! Check out his tutorial on Solaris 11 Network Tunables. And if you want to get even deeper into the networking stack, there's nothing better than DTrace. Alan Maguire teaches you in: DTracing TCP Congestion Control how to probe deeply into the Solaris 11 TCP/IP stack, the TCP congestion control part in particular. Don't miss his other DTrace and TCP related blog posts! DTrace And there we are: DTrace, the king of all observability tools. Long time DTrace veteran and co-author of The DTrace book*, Brendan Gregg blogged about Solaris 11 DTrace syscall provider changes. BTW, after you install Solaris 11, check out the DTrace toolkit which is installed by default in /usr/dtrace/DTT. It is chock full of handy DTrace scripts, many of which contributed by Brendan himself! Security Another big theme in Solaris 11, and one that is crucial for the success of any operating system in the Cloud is Security. Here are some notable posts in this category: Darren Moffat starts by showing us how to completely get rid of root: Completely Disabling Root Logins on Solaris 11. With no root user, there's one major entry point less to worry about. But that's only the start. In Immutable Zones on Encrypted ZFS, Darren shows us how to double the security of your services: First by locking them into the new Immutable Zones feature, then by encrypting their data using the new ZFS encryption feature. And if you're still missing sudo from your Linux days, Darren again has a solution: Password (PAM) caching for Solaris su - "a la sudo". If you're wondering how much compute power all this encryption will cost you, you're in luck: The Solaris X86 AESNI OpenSSL Engine will make sure you'll use your Intel's embedded crypto support to its fullest. And if you own a brand new SPARC T4 machine you're even luckier: It comes with its own SPARC T4 OpenSSL Engine. Dan Anderson's posts show how there really is now excuse not to encrypt any more... Developers Solaris 11 has a lot to offer to developers as well. Ali Bahrami has a series of blog posts that cover diverse developer topics: elffile: ELF Specific File Identification Utility, Using Stub Objects and The Stub Proto: Not Just For Stub Objects Anymore to name a few. BTW, if you're a developer and want to shape the future of Solaris 11, then Vijay Tatkar has a hint for you: Oracle (Sun Systems Group) is hiring! Desktop and Graphics Yes, Solaris 11 is a 100% server OS, but it can also offer a decent desktop environment, especially if you are a developer. Alan Coopersmith starts by discussing S11 X11: ye olde window system in today's new operating system, then Calum Benson shows us around What's new on the Solaris 11 Desktop. Even accessibility is a first-class citizen in the Solaris 11 user interface. Peter Korn celebrates: Accessible Oracle Solaris 11 - released! Performance Gone are the days of "Slowaris", when Solaris was among the few OSes that "did the right thing" while others cut corners just to win benchmarks. Today, Solaris continues doing the right thing, and it delivers the right performance at the same time. Need proof? Check out Brian's BestPerf blog with continuous updates from the benchmarking lab, including Recent Benchmarks Using Oracle Solaris 11! Send Me More Solaris 11 Launch Articles! These are just a few of the more interesting blog articles that came out around the Solaris 11 launch, I'm sure there are many more! Feel free to post a comment below if you find a particularly interesting blog post that hasn't been listed so far and share your enthusiasm for Solaris 11! *Affiliate link: Buy cool stuff and support this blog at no extra cost. We both win! var flattr_uid = '26528'; var flattr_tle = 'Solaris 11 Launch Blog Carnival Roundup'; var flattr_dsc = '<strong>Solaris 11 is here!</strong>And together with the official launch activities, a lot of Oracle and non-Oracle bloggers contributed helpful and informative blog articles to help your datacenter <a href="http://en.wikipedia.org/wiki/Up_to_eleven">go to eleven</a>.Here are some notable blog postings, sorted by category for your Solaris 11 blog-reading pleasure:'; var flattr_tag = 'blogging,digest,Oracle,Solaris,solaris,solaris 11'; var flattr_cat = 'text'; var flattr_url = 'http://constantin.glez.de/blog/2011/11/solaris-11-launch-blog-carnival-roundup'; var flattr_lng = 'en_GB'

  Read the article

• I have Oracle SQL Developer Installed, Now What?

  - by thatjeffsmith

  If you’re here because you downloaded a copy of Oracle SQL Developer and now you need help connecting to a database, then you’re in the right place. I’ll show you what you need to get up and going so you can finish your homework, teach yourself Oracle database, or get ready for that job interview. You’ll need about 30 minutes to set everything up…and about 5 years to become proficient with Oracle Oracle Database come with SQL Developer but SQL Developer doesn’t include a database If you install Oracle database, it includes a copy of SQL Developer. If you’re running that copy of SQL Developer, please take a second to upgrade now, as it is WAY out of date. But I’m here to talk to the folks that have downloaded SQL Developer and want to know what to do next. You’ve got it running. You see this ‘Connection’ dialog, and… Where am I connecting to, and who as? You NEED a database Installing SQL Developer does not give you a database. So you’re going to need to install Oracle and create a database, or connect to a database that is already up and running somewhere. Basically you need to know the following: where is this database, what’s it called, and what port is the listener running on? The Default Connection properties in SQL Developer These default settings CAN work, but ONLY if you have installed Oracle Database Express Edition (XE). Localhost is a network alias for 127.0.0.1 which is an IP address that maps to the ‘local’ machine, or the machine you are reading this blog post on. The listener is a service that runs on the server and handles connections for the databases on that machine. You can run a database without a listener and you can run a listener without a database, but you can’t connect to a database on a different server unless both that database and listener are up and running. Each listener ‘listens’ on one or more ports, you need to know the port number for each connection. The default port is 1521, but 1522 is often pretty common. I know all of this sounds very complicated Oracle is a very sophisticated piece of software. It’s not analogous to downloading a mobile phone app and and using it 10 seconds later. It’s not like installing Office/Access either – it requires services, environment setup, kernel tweaks, etc. However. Normally an administrator will setup and install Oracle, create the database, and configure the listener for everyone else to use. They’ll often also setup the connection details for everyone via a ‘TNSNAMES.ORA’ file. This file contains a list of database connection details for folks to browse – kind of like an Oracle database phoneboook. If someone has given you a TNSNAMES.ORA file, or setup your machine to have access to a TNSNAMES file, then you can just switch to the ‘TNS’ connection type, and use the dropdown to select the database you want to connect to. Then you don’t have to worry about the server names, database names, and the port numbers. ORCL – that sounds promising! ORCL is the default SID when creating a new database with the Database Creation Assistant (DBCA). It’s just me, and I need help! No administrator, no database, no nothing. What do you do? You have a few options: Buy a copy of Oracle and download, install, and create a database Download and install XE (FREE!) Download, import, and run our Developer Days Hands-on-Lab (FREE!) If you’re a student (or anyone else) with little to no experience with Oracle, then I recommend the third option. Oracle Technology Network Developer Day: Hands-on Database Application Development Lab The OTN lab runs on a A Virtual Box image which contains: 11gR2 Enterprise Edition copy of Oracle a database and listener running for you to connect to lots of demo data for you to play with SQL Developer installed and ready to connect Some browser based labs you can step through to learn Oracle You download the image, you download and install Virtual Box (also FREE!), then you IMPORT the image you previously downloaded. You then ‘Start’ the image. It will boot a copy of Oracle Enterprise Linux (OEL), start your database, and all that jazz. You can then start up and run SQL Developer inside the image OR you can connect to the database running on the image using the copy of SQL Developer you installed on your host machine. Setup Port Forwarding to Make It Easy to Connect From Your Host When you start the image, it will be assigned an IP address. Depending on what network adapter you select in the image preferences, you may get something that can get out to the internet from your image, something your host machine can see and connect to, or something that kind of just lives out there in a vacuum. You want to avoid the ‘vacuum’ option – unless you’re OK with running SQL Developer inside the Linux image. Open the Virtual Box image properties and go to the Networking options. We’re going to setup port forwarding. This will tell your machine that anything that happens on port 1521 (the default Oracle Listener port), should just go to the image’s port 1521. So I can connect to ‘localhost’ and it will magically get transferred to the image that is running. Oracle Virtual Box Port Forwarding 1521 listener database Now You Just Need a Username and Password The default passwords on this image are all ‘oracle’ – so you can connect as SYS, HR, or whatever – just use ‘oracle’ as the password. The Linux passowrds are all ‘oracle’ too, so you can login as ‘root’ or as ‘oracle’ in the Linux desktop. Connect! Connect as HR to your Oracle database running on the OTN Developer Days Virtual Box image If you’re connecting to someone else’s database, you need to ask the person that manages that environment to create for you an account. Don’t try to ‘guess’ or ‘figure out’ what the username and password is. Introduce yourself, explain your situation, and ask kindly for access. This is your first test – can you connect? I know it’s hard to get started with Oracle. There are however many things we offer to make this easier. You’ll need to do a bit of RTM first though. Once you know what’s required, you will be much more likely to succeed. Of course, if you need help, you know where to find me

  Read the article

• Fan running continously on HP Pavillion G6 notebook with 12.04.1 LTS, help please?

  - by Ankit

  Fan is running continously on my HP Pavillion G6 notebook with 12.04.1 LTS. My system specifications are:- Ram: 6Gb Graphics Card:- 1 GB (AMD Raedon 64XX). HDD: 540 GB. Please find a list of ACPI errors logs from dmesg as follows:- buffer@ankit:~$ dmesg | grep ACPI -i [ 0.000000] BIOS-e820: 000000009cebf000 - 000000009cfbf000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000009cfbf000 - 000000009cfff000 (ACPI data) [ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 HPQOEM) [ 0.000000] ACPI: XSDT 000000009cffe120 00084 (v01 HPQOEM SLIC-MPC 00000001 01000013) [ 0.000000] ACPI: FACP 000000009cffc000 000F4 (v04 HPQOEM SLIC-MPC 00000001 MSFT 01000013) [ 0.000000] ACPI: DSDT 000000009cfec000 0C132 (v01 HP 1670 00000000 MSFT 01000013) [ 0.000000] ACPI: FACS 000000009cf6c000 00040 [ 0.000000] ACPI: ASF! 000000009cffd000 000A5 (v32 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: HPET 000000009cffb000 00038 (v01 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: APIC 000000009cffa000 0008C (v02 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: MCFG 000000009cff9000 0003C (v01 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: SLIC 000000009cfeb000 00176 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013) [ 0.000000] ACPI: SSDT 000000009cfea000 00D52 (v01 HP 1670 00001000 MSFT 01000013) [ 0.000000] ACPI: BOOT 000000009cfe8000 00028 (v01 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: ASPT 000000009cfe5000 00034 (v07 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: SSDT 000000009cfe4000 00780 (v01 HP 1670 00003000 INTL 20100121) [ 0.000000] ACPI: SSDT 000000009cfe3000 00996 (v01 HP 1670 00003000 INTL 20100121) [ 0.000000] ACPI: SSDT 000000009cfdd000 0219F (v01 HP 1670 00001000 INTL 20100121) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled) [ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0]) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.005902] ACPI: Core revision 20110623 [ 0.536006] PM: Registering ACPI NVS region at 9cebf000 (1048576 bytes) [ 0.538423] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.538429] ACPI: bus type pci registered [ 0.656088] ACPI: Added _OSI(Module Device) [ 0.656094] ACPI: Added _OSI(Processor Device) [ 0.656098] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.656103] ACPI: Added _OSI(Processor Aggregator Device) [ 0.660335] ACPI: EC: Look up EC in DSDT [ 0.664416] ACPI: Executed 1 blocks of module-level executable AML code [ 0.728303] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 0.729536] ACPI: SSDT 000000009ce70798 00727 (v01 PmRef Cpu0Cst 00003001 INTL 20100121) [ 0.730622] ACPI: Dynamic OEM Table Load: [ 0.730630] ACPI: SSDT (null) 00727 (v01 PmRef Cpu0Cst 00003001 INTL 20100121) [ 0.760829] ACPI: SSDT 000000009ce71a98 00303 (v01 PmRef ApIst 00003000 INTL 20100121) [ 0.761992] ACPI: Dynamic OEM Table Load: [ 0.761998] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20100121) [ 0.792451] ACPI: SSDT 000000009ce6fd98 00119 (v01 PmRef ApCst 00003000 INTL 20100121) [ 0.793521] ACPI: Dynamic OEM Table Load: [ 0.793528] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20100121) [ 0.872981] ACPI: Interpreter enabled [ 0.872992] ACPI: (supports S0 S3 S4 S5) [ 0.873064] ACPI: Using IOAPIC for interrupt routing [ 0.882723] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62 [ 0.883072] ACPI: No dock devices found. [ 0.883084] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.883882] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe]) [ 0.924187] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.924509] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] [ 0.924581] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] [ 0.924659] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT] [ 0.924758] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG0._PRT] [ 0.924973] pci0000:00: Requesting ACPI _OSC control (0x1d) [ 0.925064] pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d [ 0.925069] ACPI _OSC control for PCIe not granted, disabling ASPM [ 0.930212] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930327] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930436] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930547] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15) [ 0.930655] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled. [ 0.930764] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled. [ 0.930873] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930979] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled. [ 0.932142] PCI: Using ACPI for IRQ routing [ 0.967119] pnp: PnP ACPI init [ 0.967151] ACPI: bus type pnp registered [ 0.968356] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.968516] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.968586] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active) [ 0.968818] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.968915] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.969206] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.969293] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.969418] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active) [ 0.969528] pnp 00:08: Plug and Play ACPI device, IDs SYN1e3f SYN1e00 SYN0002 PNP0f13 (active) [ 0.969969] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.970574] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.970617] pnp: PnP ACPI: found 11 devices [ 0.970622] ACPI: ACPI bus type pnp unregistered [ 1.138064] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.138331] ACPI: AC Adapter [ACAD] (off-line) [ 1.139068] ACPI: Lid Switch [LID0] [ 1.139176] ACPI: Power Button [PWRB] [ 1.139286] ACPI: Power Button [PWRF] [ 1.144637] ACPI: Thermal Zone [TZ01] (0 C) [ 1.144677] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.144693] ACPI: Battery Slot [BAT0] (battery present) [ 1.206926] ACPI: Battery Slot [BAT0] (battery present) [ 13.176993] acpi device:1a: registered as cooling_device4 [ 13.179931] acpi device:1b: registered as cooling_device5 [ 13.180221] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) [ 13.219589] acpi device:20: registered as cooling_device6 [ 13.220851] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 1649.915134] i8042 aux 00:08: wake-up capability disabled by ACPI [ 1649.915147] i8042 kbd 00:07: wake-up capability enabled by ACPI [ 1650.931028] r8169 0000:03:00.0: wake-up capability enabled by ACPI [ 1650.954743] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI [ 1650.978733] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI [ 1651.010950] ACPI: Preparing to enter system sleep state S3 [ 1652.251505] ACPI: Low-level resume complete [ 1652.360953] ACPI: Waking up from system sleep state S3 [ 1652.427581] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI [ 1652.435579] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI [ 1652.437887] r8169 0000:03:00.0: wake-up capability disabled by ACPI [ 1652.506660] i8042 kbd 00:07: wake-up capability disabled by ACPI [ 1661.238234] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [ 1661.238253] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [ 1661.238268] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [ 3151.784288] i8042 aux 00:08: wake-up capability disabled by ACPI [ 3151.784301] i8042 kbd 00:07: wake-up capability enabled by ACPI [ 3152.797676] r8169 0000:03:00.0: wake-up capability enabled by ACPI [ 3152.821379] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI [ 3152.845367] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI [ 3152.877600] ACPI: Preparing to enter system sleep state S3 [ 3154.313213] ACPI: Low-level resume complete [ 3154.422297] ACPI: Waking up from system sleep state S3 [ 3154.489692] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI [ 3154.497667] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI [ 3154.505947] r8169 0000:03:00.0: wake-up capability disabled by ACPI [ 3154.568985] i8042 kbd 00:07: wake-up capability disabled by ACPI [ 3162.745149] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [ 3162.745168] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [ 3162.745183] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [ 6775.723501] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [ 6775.723519] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [ 6775.723535] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [10388.004760] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [10388.004778] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [10388.004801] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [10723.591930] i8042 aux 00:08: wake-up capability disabled by ACPI [10723.591942] i8042 kbd 00:07: wake-up capability enabled by ACPI [10724.607624] r8169 0000:03:00.0: wake-up capability enabled by ACPI [10724.631349] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI [10724.655339] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI [10724.687572] ACPI: Preparing to enter system sleep state S3 [10726.123176] ACPI: Low-level resume complete [10726.232181] ACPI: Waking up from system sleep state S3 [10726.303653] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI [10726.311648] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI [10726.315734] r8169 0000:03:00.0: wake-up capability disabled by ACPI [10726.379287] i8042 kbd 00:07: wake-up capability disabled by ACPI [10734.393523] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [10734.393542] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [10734.393557] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/ps Continuous sound from the fan is very annoying, any help would highly appreciated.

  Read the article

• top Tweets SOA Partner Community – September 2012

  - by JuergenKress

  Send your tweets @soacommunity #soacommunity and follow us at http://twitter.com/soacommunity OracleBlogs ?Oracle SOA Suite for healthcare integration Dashboard http://ow.ly/1mcJvp SOA Community ?Lost in Translation &ndash; Common Mistakes Interpreting Patterns &ndash; Mark Simpson, Griffiths-Waite @ SOA, Cloud & Service… ServiceTechSymposium Matthias Zieger, Accenture just added to the agenda to co-present: "Service Modeling & BPM Business Value Patterns" http://ow.ly/ddu7A ServiceTechSymposium ?Newly updated session title and abstract: "Big Data and its impact on SOA", by Demed L'Her, Oracle. http://ow.ly/diOq2 Deepak Arora ?To PaaS or SaaS - the latest discussions with customers using SOA Suite - what are your thoughts #soa #soacommunity SOA Community top Tweets SOA Partner Community July 2012 - are you one of them? If yes please rt! https://soacommunity.wordpress.com/2012/08/28/top-tweets-soa-partner-community-august-2012/ … #soacommunity Sandor Nieuwenhuijs Checkout the BeNeLux Architectural Networking Event during Oracle Open World - meet your peers and the experts http://www.ddg-servicecenter.com/networkmanager/oow/architect/default.aspx … SOA Community ?top Tweets SOA Partner Community &ndash; August 2012 http://wp.me/p10C8u-uf SOA Community ?Follow SOA Community on facebook http://www.facebook.com/soacommunity #soacommunity SOA Community ?New Service to promote Your SOA & BPM events at http://oracle.com/events for SOA & BPM Specialized Partners Only! #soacommunity #opn #oracle Jan van Zoggel ?Hotel check, flight check, overview of sessions to visit check http://jvzoggel.wordpress.com/2012/08/27/soa-cloud-servicetech-symposium/ … I'm ready for SOA, Cloud & Service Technology Symposium SOA Community SOA & BPM Specialized Partners Only! New Service to Promote Your SOA & BPM Events at http://oracle.com/events http://wp.me/p10C8u-sH SOA Community Call for content for the next community newsletter. Do you want to publish your success & best practice? Send it @soacommunity #soacommunity SOA Community SOA Adoption in the Brazilian Ministry of Health - Case Study by Ricardo Puttini, University of Brasilia @ SOA, Cloud & Service… Jan van Zoggel ?Just registered for the 5th International SOA, Cloud & Service Technology Symposium in London. Looking forward to it. http://www.servicetechsymposium.com/ OTNArchBeat ?Want to prepare for Oracle SOA Specialization? @t_winterberg offers a suggestion. http://pub.vitrue.com/5Hqu OTNArchBeat ?Oracle BPM enable BAM | @deltalounge http://pub.vitrue.com/BCwj SOA Community Presentations & Training material OFM Summer Camps & Impressions & Feedback http://wp.me/p10C8u-sF Emiel Paasschens Nice! Pdf document on how to use a #Oracle #SOA Suite Domain Value Map (DVM) in the OSB: http://bit.ly/RzyS9w #yam OracleBlogs ?Using Cloud OER to Find Fusion Applications On-Premise Service Concrete WSDL URL http://ow.ly/1m4lz7 demed ?Free VIP pass for @techsymp if you are in London Sep. 24-25. Be the first one to retweet this and I'll DM you details! http://www.servicetechsymposium.com/speaker_bios.php?id=demed_lher … Jan van Zoggel blogpost: Oracle Service Bus duplicate message check using Oracle Coherence caching http://jvzoggel.wordpress.com/2012/08/20/osb-duplicate-message-with-coherence/ … OTNArchBeat ?Oracle Service Bus duplicate message check using Coherence | @jvzoggel http://pub.vitrue.com/ckY8 Oracle UPK & Tutor Synaptis and Oracle Present: Leveraging UPK Throughout the Project Lifecycle: Leveraging UPK throughout the Proj... http://bit.ly/OS2Rbg Rolando Carrasco ?New entry @ oracleradio http://bit.ly/SEvwwS @soacommunity @oracleace How to identify duplicated messages on Oracle SOA SUITE? SOA Community ?Business Driven Development (BDD) Demo Now Available! http://wp.me/p10C8u-sf OTNArchBeat ?Installing Oracle SOA Suite10g on Oracle Enterprise Linux | @lonnekedikmans http://pub.vitrue.com/BEyD OTNArchBeat ?Best practices for Oracle real-time data integration | Frank Ohlhorst http://pub.vitrue.com/1fH1 ServiceTechSymposium ?New OTN podcast featuring speakers Thomas Erl, Tim Hall and Demed L’Her just published. Tune into 1st 3 parts here: http://ow.ly/d1RRn OTNArchBeat ?SOA, Cloud, and Service Technologies - Part 4 of 4 - Best selling SOA author Thomas Erl talks about the latest title... http://ow.ly/1m0txY SOA Community Win a free conference pass for the SOA, Cloud + Service Technology Symposium &ndash; become a soacommunity facebook fan!… Lonneke Dikmans VENNSTER BLOG: Installing Oracle SOA Suite10g on Oracle Enterpris... http://blog.vennster.nl/2012/08/installing-oracle-soa-suite-10g-on.html?spref=tw … PeterPaul vande Beek published a blog on exporting Oracle #BPM metrics to a #DWH http://www.deltalounge.net/wpress/2012/08/export-oracle-bpm-metrics-to-a-data-warehouse/ … #soacommunity SOA Community ?Do you follow us on facebook http://www.facebook.com/soacommunity #soacommunity C2B2 Consulting ?Cloud-based Enterprise Architecture by Steve Millidge, C2B2 Consulting @ SOA, Cloud &amp; Service … http://wp.me/p10C8u-sv via @soacommunity Gertjan van het Hof Storing SCA Metadata in the Oracle Metadata Services Repository http://www.oracle.com/technetwork/articles/soa/fonnegra-storing-sca-metadata-1715004.html?msgid=3-6903117805 … arjankramer ?Encrypted OSB Service account passwords http://dlvr.it/20hbNV Richard van Tilborg BPM the Battle http://lnkd.in/yFAJaW OTNArchBeat Using Cloud OER to Find Fusion Applications On-Premise Service Concrete WSDL URL | @RahejaRajesh http://pub.vitrue.com/YDCD SOA Proactive ?Webcast: Introduction to SOA Human Workflow, 8/23, 10 AM EDT. Register @ http://bit.ly/Nx77sY Lucas Jellema ?Programmatically admnistration of OSB using JXM & MBeans. Interesting example is given in https://blogs.oracle.com/ateamsoab2b/entry/automatic_disabling_proxy_service_when … orclateamsoa ?A-Team Blog #ateam: Automatically Disable Proxy Service to avoid overloading OSB http://ow.ly/1lXGKV Atul_Kumar ?Oracle Enterprise Gateway – OEG 11gR1 (11.1.1.*) for beginners http://goo.gl/fb/EJboE Estafet Limited Advanced SOA Boot camp @soacommunity in Munich was excellent.@wlscommunity Learnt a lot and liked the format. SOA Community Oracle Fusion Applications Design Patterns Now Available For Developers by Ultan O'Broin http://wp.me/p10C8u-sd SOA & BPM Partner Community For regular information on Oracle SOA Suite become a member in the SOA & BPM Partner Community for registration please visit  www.oracle.com/goto/emea/soa (OPN account required) If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix Forum Technorati Tags: SOA Community twitter,SOA Community,Oracle SOA,Oracle BPM,BPM Community,OPN,Jürgen Kress

  Read the article

• Eine komplette Virtualisierungslandschaft auf dem eigenen Laptop – So geht’s

  - by Manuel Hossfeld

  Eine komplette Virtualisierungslandschaftauf dem eigenen Laptop – So geht’s Wenn man sich mit dem Virtualisierungsprodukt Oracle VM in der aktuellen Version 3.x näher befassen möchte, bietet es sich natürlich an, eine eigene Umgebung zu Lern- und Testzwecken zu installieren. Doch leichter gesagt als getan: Bei näherer Betrachtung der Architektur wird man schnell feststellen, dass mehrere Rechner benötigt werden, um überhaupt alle Komponenten abbilden zu können: Zum einen gilt es, den oder die OVM Server selbst zu installieren. Das ist recht leicht und schnell erledigt, aber da Oracle VM ein „Typ 1 Hypervisor ist“ - also direkt auf dem Rechner („bare metal“) installiert wird – ist der eigenen Arbeits-PC oder Laptop dafür recht ungeeignet. (Eine Dual-Boot Umgebung wäre zwar denkbar, aber recht unpraktisch.) Zum anderen wird auch ein Rechner benötigt, auf dem der OVM Manager installiert wird. Im Gegensatz zum OVM Server erfolgt dessen Installation nicht „bare metal“, sondern auf einem bestehenden Oracle Linux. Aber was tun, wenn man gerade keinen Linux-Server griffbereit hat und auch keine extra Hardware dafür opfern will? Möchte man alle Funktionen von Oracle VM austesten, so sollte man zusätzlich über einen Shared Storag everüfugen. Dieser kann wahlweise über NFS oder über ein SAN (per iSCSI oder FibreChannel) angebunden werden. Zwar braucht man zum Testen nicht zwingend entsprechende „echte“ Storage-Hardware, aber auch die „Simulation“ entsprechender Komponenten erfordert zusätzliche Hardware mit entsprechendem freien Plattenplatz.(Alternativ können auch fertige „Software Storage Appliances“ wie z.B. OpenFiler oder FreeNAS verwendet werden). Angenommen, es stehen tatsächlich keine „echte“ Server- und Storage Hardware zur Verfügung, so benötigt man für die oben genannten drei Punkte  drei bzw. vier Rechner (PCs, Laptops...) - je nachdem ob man einen oder zwei OVM Server starten möchte. Erfreulicherweise geht es aber auch mit deutlich weniger Aufwand: Wie bereits kurz im Blogpost anlässlich des letzten OVM-Releases 3.1.1 beschrieben, ist die aktuelle Version in der Lage, selbst vollständig innerhalb von VirtualBox als Gast zu laufen. Wer bei dieser „doppelten Virtualisierung“ nun an das Prinzip der russischen Matroschka-Puppen denkt, liegt genau richtig. Oracle VM VirtualBox stellt dabei gewissermaßen die äußere Hülle dar – und da es sich bei VirtualBox im Gegensatz zu Oracle VM Server um einen „Typ 2 Hypervisor“ handelt, funktioniert dieser Ansatz auch auf einem „normalen“ Arbeits-PC bzw. Laptop, ohne dessen eigentliche Betriebsystem komplett zu überschreiben. Doch das beste dabei ist: Die Installation der jeweiligen VirtualBox VMs muss man nicht selber durchführen. Der OVM Manager als auch der OVM Server stehen bereits als vorgefertigte „VirtualBox Appliances“ im Oracle Technology Network zum Download zur Verfügung und müssen im Grunde nur noch importiert und konfiguriert werden. Das folgende Schaubild verdeutlicht das Prinzip: Die dunkelgrünen Bereiche stellen jeweils Instanzen der eben erwähnten VirtualBox Appliances für OVM Server und OVM Manager dar. (Hier im Bild sind zwei OVM Server zu sehen, als Minimum würde natürlich auch einer genügen. Dann können aber viele Features wie z.B. OVM HA nicht ausprobieren werden.) Als cleveren Trick zur Einsparung einer weiteren VM für Storage-Zwecke hat Wim Coekaerts (Senior Vice President of Linux and Virtualization Engineering bei Oracle), der „Erbauer“ der VirtualBox Appliances, die OVM Manager Appliance bereits so vorbereitet, dass diese gleichzeitig als NFS-Share (oder ggf. sogar als iSCSI Target) dienen kann. Dies beschreibt er auch kurz auf seinem Blog. Die hellgrünen Ovale stellen die VMs dar, welche dann innerhalb einer der virtualisierten OVM Server laufen können. Aufgrund der Tatsache, dass durch diese „doppelte Virtualisierung“ die Fähigkeit zur Hardware-Virtualisierung verloren geht, können diese „Nutz-VMs“ demzufolge nur paravirtualisiert sein (PVM). Die hier in blau eingezeichneten Netzwerk-Schnittstellen sind virtuelle Interfaces, welche beliebig innerhalb von VirtualBox eingerichtet werden können. Wer die verschiedenen Netzwerk-Rollen innerhalb von Oracle VM im Detail ausprobieren will, kann hier natürlich auch mehr als zwei dieser Interfaces konfigurieren. Die Vorteile dieser Lösung für Test- und Demozwecke liegen auf der Hand: Mit lediglich einem PC bzw. Laptop auf dem VirtualBox installiert ist, können alle oben genannten Komponenten installiert und genutzt werden – genügend RAM vorausgesetzt. Als Minimum darf hier 8GB gelten. Soll auf der „Host-Umgebung“ (also dem PC auf dem VirtualBox läuft) nebenbei noch gearbeiten werden und/oder mehrere „Nutz-VMs“ in dieser simulierten OVM-Server-Umgebung laufen, empfehlen sich natürlich eher 16GB oder mehr. Da die nötigen Schritte zum Installieren und initialen Konfigurieren der Umgebung ausführlich in einem entsprechenden Paper beschrieben sind, möchte ich im Rest dieses Artikels noch einige zusätzliche Tipps und Details erwähnen, welche einem das Leben etwas leichter machen können: Um möglichst entstpannt und mit zusätzlichen „Sicherheitsnetz“ an die Konfiguration der Umgebung herangehen zu können, empfiehlt es sich, ausgiebigen Gebrauch von der in VirtualBox eingebauten Funktionalität der VM Snapshots zu machen. Dies ermöglicht nicht nur ein Zurücksetzen falls einmal etwas schiefgehen sollte, sondern auch ein beliebiges Wiederholen von bereits absolvierten Teilschritten (z.B. um eine andere Idee oder Variante der Umgebung auszuprobieren). Sowohl bei den gerade erwähnten Snapshots als auch bei den VMs selbst sollte man aussagekräftige Namen verwenden. So ist sichergestellt, dass man nicht durcheinander kommt und auch nach ein paar Wochen noch weiß, welche Umgebung man da eigentlich vor sich hat. Dies beinhaltet auch die genaue Versions- und Buildnr. des jeweiligen OVM-Releases. (Siehe dazu auch folgenden Screenshot.) Weitere Informationen und Details zum aktuellen Zustand sowie Zweck der jeweiligen VMs kann in dem oft übersehenen Beschreibungsfeld hinterlegt werden. Es empfiehlt sich, bereits VOR der Installation einen Notizzettel (oder eine Textdatei) mit den geplanten IP-Adressen und Namen für die VMs zu erstellen. (Nicht vergessen: Auch der Server Pool benötigt eine eigene IP.) Dabei sollte man auch nochmal die tatsächlichen Netzwerke der zu verwendenden Virtualbox-Interfaces prüfen und notieren. Achtung: Es gibt im Rahmen der Installation einige Passworte, die vom Nutzer gesetzt werden können – und solche, die zunächst fest eingestellt sind. Zu letzterem gehört das Passwort für den ovs-agent sowie den root-User auf den OVM Servern, welche beide per Default „ovsroot“ lauten. (Alle weiteren Passwort-Informationen sind in dem „Read me first“ Dokument zu finden, welches auf dem Desktop der OVM Manager VM liegt.) Aufpassen muss man ggf. auch in der initialen „Interview-Phase“ welche die VirtualBox VMs durchlaufen, nachdem sie das erste mal gebootet werden. Zu diesem Zeitpunkt ist nämlich auf jeden Fall noch die amerikanische Tastaturbelegung aktiv, so dass man z.B. besser kein „y“ und „z“ in seinem selbst gewählten Passwort verwendet. Aufgrund der Tatsache, dass wie oben erwähnt der OVM Manager auch gleichzeitig den Shared Storage bereitstellt, sollte darauf geachtet werden, dass dessen VM vor den OVM Server VMs gestartet wird. (Andernfalls „findet“ der dem OVM Server Pool zugrundeliegende Cluster sein sog. „Server Pool File System“ nicht.)

  Read the article

• Customize the Default Screensavers in Windows 7 and Vista

  - by Matthew Guay

  Windows 7 and Vista include a nice set of backgrounds, but unfortunately most of them aren’t configurable by default.  Thanks to a free app and some registry changes, however, you can make the default screensavers uniquely yours! Customize the default screensavers If you’ve ever pressed the Customize button on most of the default screensavers in Windows 7 and Vista, you were probably greeted with this message: A little digging in the registry shows that this isn’t fully correct.  The default screensavers in Vista and 7 do have options you can set, but they’re not obvious.  With the help of an app or some registry tips, you can easily customize the screensavers to be uniquely yours.  Here’s how you can do it with an app or in the registry. Customize Windows Screensavers with System Screensavers Tweaker Download the System Screensavers Tweaker (link below), and unzip the folder.  Run nt6srccfg.exe in the folder to tweak your screensavers.  This application lets you tweak the screensavers’ registry settings graphically, and it works great in all editions of Windows Vista and 7, including x64 versions. Change any of the settings you want in the screensaver tweaker, and click Apply. To preview the changes to your screensaver, open the Screen Saver settings window as normal by right-clicking on the desktop, and selecting Personalize. Click on the Screensaver button on the bottom right. Now, select your modified screensaver, and click Preview to see your changes. You can change a wide variety of settings for the Bubbles, Ribbons, and Mystify screensavers in Windows 7 and Vista, as well as the Aurora screensaver in Windows Vista.  The tweaks to the Bubbles screensaver are especially nice.  Here’s how the Bubbles look without transparency. And, by tweaking a little more, you get a screensaver that looks more like a screen full of marbles. Ribbons and Mystify each have less settings, but still can produce some unique effects.   How’s that for a brilliant screensaver? And, if you want to return your screensavers to their default settings, simply run the System Screensavers Tweaker and select Reset to defaults on any screensaver you wish to reset. Customize Windows Screensavers in the Registry If you prefer to roll up your sleeves and tweak Windows under-the-hood, then here’s how you can customize the screensavers yourself in the Registry.  Type regedit into the search box in the Start menu, browse to the key for each screensaver, and add or modify the DWORD values listed for that screensaver using the Decimal base. Please Note: Tweaking the Registry can be difficult, so if you’re unsure, just use the tweaking application above. Also, you’ll probably want to create a System Restore Point.   Bubbles To edit the Bubbles screensaver, browse to the following in regedit: HKEY_CURRENT_USER\Software\Microsoft\Windows\Current Version\Screensavers\Bubbles Now, add or modify the following DWORD values to tweak the screensaver: MaterialGlass – enter 0 for solid or 1 for transparent bubbles Radius – enter a number between 1090000000 and 1130000000; the larger the number, the larger the bubbles’ radius ShowBubbles – enter 0 to show a black background or 1 to show the current desktop behind the bubbles ShowShadows – enter 0 for no shadow or 1 for shadows behind the bubbles SphereDensity – enter a number from 1000000000 to 2100000000; the higher the number, the more bubbles on the screen. TurbulenceNumOctaves – enter a number from 1 to 255; the higher the number, the faster the bubble colors will change. Ribbons To edit the Ribbons screensaver, browse to the following in regedit: HKEY_CURRENT_USER\Software\Microsoft\Windows\Current Version\Screensavers\Ribbons Now, add or modify the following DWORD values to tweak the screensaver: Blur – enter 0 to prevent ribbons from fading, or 1 to have them fade away after a few moments. Numribbons – enter a number from 1 to 100; the higher the number, the more ribbons on the screen. RibbonWidth – enter a number from 1000000000 to 1080000000; the higher the number, the thicker the ribbons. Mystify To edit the Mystify screensaver, browse to the following in regedit: HKEY_CURRENT_USER\Software\Microsoft\Windows\Current Version\Screensavers\Mystify Now, add or modify the following DWORD values to tweak the screensaver: Blur – enter 0 to prevent lines from fading, or 1 to have them fade away after a few moments. LineWidth – enter a number from 1000000000 to 1080000000; the higher the number, the wider the lines. NumLines – enter a number from 1 to 100; the higher the value, the more lines on the screen. Aurora – Windows Vista only To edit the Aurora screensaver in Windows Vista, browse to the following in regedit: HKEY_CURRENT_USER\Software\Microsoft\Windows\Current Version\Screensavers\Aurora Now, add or modify the following DWORD values to tweak the screensaver: Amplitude – enter a value from 500000000 to 2000000000; the higher the value, the slower the motion. Brightness – enter a value from 1000000000 to 1050000000; the higher the value, the brighter the affect. NumLayers – enter a value from 1 to 15; the higher the value, the more aurora layers displayed. Speed – enter a value from 1000000000 to 2100000000; the higher the value, the faster the cycling. Conclusion Although the default screensavers are nice, they can be boring after awhile with their default settings.  But with these tweaks, you can create a variety of vibrant screensavers that should keep your desktop fresh and interesting. Link Download the System Screensavers Tweaker Similar Articles Productive Geek Tips Create Icons to Start the Screensaver on Windows 7 or VistaMake Your Windows XP Logon Screen Look Like Windows VistaSpeed up Windows Vista Start Menu Search By Limiting ResultsRoundup: 16 Tweaks to Windows Vista Look & FeelSet XP as the Default OS in a Windows Vista Dual-Boot Setup TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 NachoFoto Searches Images in Real-time Office 2010 Product Guides Google Maps Place marks – Pizza, Guns or Strip Clubs Monitor Applications With Kiwi LocPDF is a Visual PDF Search Tool Download Free iPad Wallpapers at iPad Decor

  Read the article

• Flashing your Windows Phone Dummies

  - by Martin Hinshelwood

  The rate at which vendors release new updates for the HD2 is ridiculously slow. You have to wait for Microsoft to release the new OS, then you wait for HTC to build it into a ROM, and then you have to wait up to 6 months for your operator to badly customise it for their network. Once Windows Phone 7 is released this problem should go away as Microsoft is likely to be able to update the phone over the air, but what do we do until then? I want Windows Mobile 6.5.5 now!   I’m an early adopter. If there is a new version of something then that’s the version I want. As long as you accept that you are using something on a “let the early adopter beware” and accept that there may be bugs, sometimes serious crippling bugs the go for it. Note that I won't be responsible if you end up bricking your phone, unlocking or flashing your radio or ROM can be risky. If you follow the instructions then you should be fine, I've flashed my phones (SPV, M300, M1000, M2000, M3100, TyTN, TyTN 2, HD2) hundreds of times without any problems! I have been using Windows Mobile 6.5.5 before it was called 6.5.5 and for long enough that I don’t even remember when I first started using it. I was using it on my HTC TyTN 2 before I got an HD2 a couple of months before Christmas, and the first custom ROM’s for the HD2 were a couple of months after that. I always update to the latest ROM that I like, and occasionally I go back to the stock ROM’s to have a look see, but I am always disappointed. Terms: Soft Reset: Same as pulling out the battery, but is like a reboot for your phone Hard Reset: Reinstalls the Operating system from the Image that is stored on it ROM: This is Image that is loaded onto your phone and it is used to reinstall your phone whenever you do a “hard reset”. Stock ROM: A ROM from the original vendor… So HTC Cook a ROM: Referring to Cooking a ROM is the process a ROM developer goes through to take all of the parts (OS, Drivers and Applications) that make up a running phone and compiling them into a ROM. ROM Kitchen: A place where you get an SDK and all the component parts of the phone: OD, Drivers and Application. There are usually lots of Tools for making it easier to compile and build the image. Flashing: The process of updating one of the layers of your phone with a new layer Bricked: This is what happens when flashing goes wrong. Your phone is now good for only one thing… stopping paper blowing away in a windy place. You can “cook” you own ROM using one of the many good “ROM Kitchens” or you can use a ROM built and tested by someone else. I have cooked my own ROM before, and while the tutorials are good, it is a lot of hassle. You can only Flash new ROM’s that are specifically for your phone only so find a ROM for your phone and XDA Developers is the best place to look. It has a forum based structure and you can find your phone quite easily. XDA Developer Forum Installing a new ROM does have its risks. In the past there have been stories about phones being “bricked” but I have not heard of a bricked phone for quite some years. if you follow the instructions carefully you should not have any problems. note: Most of the tools are written by people for whom English is not their first language to you will need concentrate hard to understand some of the instructions. Have you ever read a manual that was just literally translated from another language? Enough said… There are a number of layers on your phone that you will need to know about: SPL: This is the lowest level, like a BIOS on a PC and is the Operating Systems gateway to the hardware Radio: I think of this as the hardware drivers, and you will need a different Radio for CDMA than GSM networks ROM: This is like your Windows CD, but it is stored internally to the Phone. Flashing your phone consists of replacing one Image with another and then wiping your phone and automatically reinstall from the Image. Sometimes when you download an Image wither it is for a Radio or for ROM you only get a file called *.nbh. What do you do with this? Well you need an RUU application to push that Image to your phone. The RUU’s are different per phone, but there is a CustomRUU for the HD2 that will update your phone with any *.nbh placed in the same directory. Download and Instructions for CustomRUU #1 Flash HardSPL An SPL is kind of like a BIOS, and the default one has checks to make sure that you are only installing a signed ROM. This would prevent you from installing one that comes from any other source but the vendor. NOTE: Installing a HARD SPL invalidates your warranty so remember to Flash your phone with a “stock” vendor ROM before trying to send your phone in for repairs. Is the warranty reinstated when you go back to a stock ROM? I don’t know… Updating your SPL to a HardSPL effectively unlocks your phone so you can install anything you like. I would recommend the HardSPL2. Download and Instructions for HardSPL2 #2 Task29 One of the problems that has been seen on the HD2 when flashing new ROM’s is that things are left over from the old ROM. For a while the recommendation was to Flash a stock ROM first, but some clever cookies have come up with “Task29” which formats your phone first. After running this your phone will be blank and will only boot to the white HTC logo and no further. You should follow the instructions and reboot (remove battery) and hold down the “volume down” button while turning you HD2 on to enter the bootloader. From here you can run CustomRUU once the USB message appears. Download and Instructions for Task29 #2 Flash Radio You may need to play around with this one, there is no good and bad version and the latest is not always the best. You know that annoying thing when you hit “end call” on your phone and nothing happens? Well that's down to the Radio. Get this version right for you and you may even be able to make calls. From a Windows Mobile as well Download There are no instructions here, but they are the same as th ROM, but you use this *.nbh file. #3 Flash ROM If you have gotten this far then you are probably a pro by now Just download the latest ROM below and Flash to your phone. I have been really impressed by the Artemis line of ROM’s but it is no way the only choice. I like this one as the developer builds them as close to the stock ROM as possible while updating to the latest of everything. Download and Instructions for  Artemis HD2 vXX Conclusion While updating your ROM is not for the faint hearted it provides more options than the Stock ROM’s and quicker feature updates than waiting… Technorati Tags: WM6

  Read the article

• AngularJs ng-cloak Problems on large Pages

  - by Rick Strahl

  I’ve been working on a rather complex and large Angular page. Unlike a typical AngularJs SPA style ‘application’ this particular page is just that: a single page with a large amount of data on it that has to be visible all at once. The problem is that when this large page loads it flickers and displays template markup briefly before kicking into its actual content rendering. This is is what the Angular ng-cloak is supposed to address, but in this case I had no luck getting it to work properly. This application is a shop floor app where workers need to see all related information in one big screen view, so some of the benefits of Angular’s routing and view swapping features couldn’t be applied. Instead, we decided to have one very big view but lots of ng-controllers and directives to break out the logic for code separation. For code separation this works great – there are a number of small controllers that deal with their own individual and isolated application concerns. For HTML separation we used partial ASP.NET MVC Razor Views which made breaking out the HTML into manageable pieces super easy and made migration of this page from a previous server side Razor page much easier. We were also able to leverage most of our server side localization without a lot of  changes as a bonus. But as a result of this choice the initial HTML document that loads is rather large – even without any data loaded into it, resulting in a fairly large DOM tree that Angular must manage. Large Page and Angular Startup The problem on this particular page is that there’s quite a bit of markup – 35k’s worth of markup without any data loaded, in fact. It’s a large HTML page with a complex DOM tree. There are quite a lot of Angular {{ }} markup expressions in the document. Angular provides the ng-cloak directive to try and hide the element it cloaks so that you don’t see the flash of these markup expressions when the page initially loads before Angular has a chance to render the data into the markup expressions.<div id="mainContainer" class="mainContainer boxshadow" ng-app="app" ng-cloak> Note the ng-cloak attribute on this element, which here is an outer wrapper element of the most of this large page’s content. ng-cloak is supposed to prevent displaying the content below it, until Angular has taken control and is ready to render the data into the templates. Alas, with this large page the end result unfortunately is a brief flicker of un-rendered markup which looks like this: It’s brief, but plenty ugly – right?  And depending on the speed of the machine this flash gets more noticeable with slow machines that take longer to process the initial HTML DOM. ng-cloak Styles ng-cloak works by temporarily hiding the marked up element and it does this by essentially applying a style that does this:[ng\:cloak], [ng-cloak], [data-ng-cloak], [x-ng-cloak], .ng-cloak, .x-ng-cloak { display: none !important; } This style is inlined as part of AngularJs itself. If you looking at the angular.js source file you’ll find this at the very end of the file:!angular.$$csp() && angular.element(document) .find('head') .prepend('<style type="text/css">@charset "UTF-8";[ng\\:cloak],[ng-cloak],' + '[data-ng-cloak],[x-ng-cloak],.ng-cloak,.x-ng-cloak,' + '.ng-hide{display:none !important;}ng\\:form{display:block;}' '.ng-animate-block-transitions{transition:0s all!important;-webkit-transition:0s all!important;}' + '</style>'); This is is meant to initially hide any elements that contain the ng-cloak attribute or one of the other Angular directive permutation markup. Unfortunately on this particular web page ng-cloak had no effect – I still see the flicker. Why doesn’t ng-cloak work? The problem is of course – timing. The problem is that Angular actually needs to get control of the page before it ever starts doing anything like process even the ng-cloak attribute (or style etc). Because this page is rather large (about 35k of non-data HTML) it takes a while for the DOM to actually plow through the HTML. With the Angular <script> tag defined at the bottom of the page after the HTML DOM content there’s a slight delay which causes the flicker. For smaller pages the initial DOM load/parse cycle is so fast that the markup never shows, but with larger content pages it may show and become an annoying problem. Workarounds There a number of simple ways around this issue and some of them are hinted on in the Angular documentation. Load Angular Sooner One obvious thing that would help with this is to load Angular at the top of the page  BEFORE the DOM loads and that would give it much earlier control. The old ng-cloak documentation actually recommended putting the Angular.js script into the header of the page (apparently this was recently removed), but generally it’s not a good practice to load scripts in the header for page load performance. This is especially true if you load other libraries like jQuery which should be loaded prior to loading Angular so it can use jQuery rather than its own jqLite subset. This is not something I normally would like to do and also something that I’d likely forget in the future and end up right back here :-). Use ng-include for Child Content Angular supports nesting of child templates via the ng-include directive which essentially delay loads HTML content. This helps by removing a lot of the template content out of the main page and so getting control to Angular a lot sooner in order to hide the markup template content. In the application in question, I realize that in hindsight it might have been smarter to break this page out with client side ng-include directives instead of MVC Razor partial views we used to break up the page sections. Razor partial views give that nice separation as well, but in the end Razor puts humpty dumpty (ie. the HTML) back together into a whole single and rather large HTML document. Razor provides the logical separation, but still results in a large physical result document. But Razor also ended up being helpful to have a few security related blocks handled via server side template logic that simply excludes certain parts of the UI the user is not allowed to see – something that you can’t really do with client side exclusion like ng-hide/ng-show – client side content is always there whereas on the server side you can simply not send it to the client. Another reason I’m not a huge fan of ng-include is that it adds another HTTP hit to a request as templates are loaded from the server dynamically as needed. Given that this page was already heavy with resources adding another 10 separate ng-include directives wouldn’t be beneficial :-) ng-include is a valid option if you start from scratch and partition your logic. Of course if you don’t have complex pages, having completely separate views that are swapped in as they are accessed are even better, but we didn’t have this option due to the information having to be on screen all at once. Avoid using {{ }}  Expressions The biggest issue that ng-cloak attempts to address isn’t so much displaying the original content – it’s displaying empty {{ }} markup expression tags that get embedded into content. It gives you the dreaded “now you see it, now you don’t” effect where you sometimes see three separate rendering states: Markup junk, empty views, then views filled with data. If we can remove {{ }} expressions from the page you remove most of the perceived double draw effect as you would effectively start with a blank form and go straight to a filled form. To do this you can forego {{ }}  expressions and replace them with ng-bind directives on DOM elements. For example you can turn:<div class="list-item-name listViewOrderNo"> <a href='#'>{{lineItem.MpsOrderNo}}</a> </div>into:<div class="list-item-name listViewOrderNo"> <a href="#" ng-bind="lineItem.MpsOrderNo"></a> </div> to get identical results but because the {{ }}  expression has been removed there’s no double draw effect for this element. Again, not a great solution. The {{ }} syntax sure reads cleaner and is more fluent to type IMHO. In some cases you may also not have an outer element to attach ng-bind to which then requires you to artificially inject DOM elements into the page. This is especially painful if you have several consecutive values like {{Firstname}} {{Lastname}} for example. It’s an option though especially if you think of this issue up front and you don’t have a ton of expressions to deal with. Add the ng-cloak Styles manually You can also explicitly define the .css styles that Angular injects via code manually in your application’s style sheet. By doing so the styles become immediately available and so are applied right when the page loads – no flicker. I use the minimal:[ng-cloak] { display: none !important; } which works for:<div id="mainContainer" class="mainContainer dialog boxshadow" ng-app="app" ng-cloak> If you use one of the other combinations add the other CSS selectors as well or use the full style shown earlier. Angular will still load its version of the ng-cloak styling but it overrides those settings later, but this will do the trick of hiding the content before that CSS is injected into the page. Adding the CSS in your own style sheet works well, and is IMHO by far the best option. The nuclear option: Hiding the Content manually Using the explicit CSS is the best choice, so the following shouldn’t ever be necessary. But I’ll mention it here as it gives some insight how you can hide/show content manually on load for other frameworks or in your own markup based templates. Before I figured out that I could explicitly embed the CSS style into the page, I had tried to figure out why ng-cloak wasn’t doing its job. After wasting an hour getting nowhere I finally decided to just manually hide and show the container. The idea is simple – initially hide the container, then show it once Angular has done its initial processing and removal of the template markup from the page. You can manually hide the content and make it visible after Angular has gotten control. To do this I used:<div id="mainContainer" class="mainContainer boxshadow" ng-app="app" style="display:none"> Notice the display: none style that explicitly hides the element initially on the page. Then once Angular has run its initialization and effectively processed the template markup on the page you can show the content. For Angular this ‘ready’ event is the app.run() function:app.run( function ($rootScope, $location, cellService) { $("#mainContainer").show(); … }); This effectively removes the display:none style and the content displays. By the time app.run() fires the DOM is ready to displayed with filled data or at least empty data – Angular has gotten control. Edge Case Clearly this is an edge case. In general the initial HTML pages tend to be reasonably sized and the load time for the HTML and Angular are fast enough that there’s no flicker between the rendering times. This only becomes an issue as the initial pages get rather large. Regardless – if you have an Angular application it’s probably a good idea to add the CSS style into your application’s CSS (or a common shared one) just to make sure that content is always hidden. You never know how slow of a browser somebody might be running and while your super fast dev machine might not show any flicker, grandma’s old XP box very well might…© Rick Strahl, West Wind Technologies, 2005-2014Posted in Angular  JavaScript  CSS  HTML   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

  Read the article

• TechEd 2010 Day One – How I Travel

  - by BuckWoody

  Normally when I blog on the first day of a conference, well, there hasn’t been a first day yet. So I talk about the value of a conference or some other facet. And normally in my (non-conference) blogs, I show you how I have learned to be a data professional – things I’ve learned how to do over the years. But in all that time, I don’t think I’ve ever talked about a big part of my job – traveling. I’ve traveled a lot throughout the years, when I’ve taught, gone to conferences, consulted and in my current role assisting Microsoft customers with large-scale database system designs.  So I’ll share a few thoughts about what I do. Keep in mind that I travel for short durations, just a day or so, and sometimes I travel internationally. For those I prepare differently – what I’m talking about here is what I do for a multi-day, same-country trip. Hopefully you find it useful. I’ll tag a few other travelers I know to add their thoughts.  Preparing for Travel   When I’m notified of a trip, I begin researching the location. I find the flights, hotel and (if I have to) a car to use while I’m away. We have an in-house system we use to book the travel, but when I travel not-for-Microsoft I use Expedia and Kayak to find what I need.  Traveling on Sunday and Friday is the worst. I have to do it sometimes (like this week) and it’s always a bad idea. But you can blunt the impact by booking as early as you can stand it. That means I have to be up super-early, but the flights are normally on time. I stay flexible, and always have a backup plan in case the flights are delayed or canceled.  For the hotel, I tend to go on the cheaper side, and I look for older hotels that have been renovated, or quirky ones. For instance, in Boise, ID recently I stayed at a 60’s-themed (think Mad-Men) hotel that was very cool. Always I go on the less expensive side – I find the “luxury” hotels nail me for Internet, food, everything. The cheaper places include all kinds of things, and even have breakfasts, shuttles and all kinds of things that start to add up. I even call ahead to make sure there’s an iron and ironing board available, since I’ll need those when I get there.  I find any way I can not to get a car. I use mass-transit wherever possible, and try to make friends and pay their gas to take me places. In a pinch, I’ll use a taxi. It ends up being cheaper, faster, and less stressful all around.  Packing  Over the years I’ve learned never to check luggage whenever I can. To do that, I lay out everything I want to take with me on the bed, and then try and make sure I’m really going to use it. I wear a dark wool set of pants, which I can clean and wear in hot and cold climates. I bring undies and socks of course, and for most places I have to wear “dress up” shirts. I bring at least two print T-Shirts in case I want to dress down for something while I’m gone, but I only bring one set of shoes. All the  clothes are rolled as tightly as possible as I learned in the military. Then I use those to cushion the electronics I take.  For toiletries I bring a shaver, toothpaste and toothbrush, D/O and a small brush. Everything else the hotel will provide.  For entertainment, I take a small Zune, a full PC-Headset (so I can make IP calls on the road) and my laptop. I don’t take books or anything else – everything is electronic. I use E-books (downloaded from our Library), Audio-Books (on the Zune) and I also bring along a Kaossilator (more here) to play music in the hotel room or even on the plane without being heard.  If I can, I pack into one roll-on bag. There’s not a lot better than this one, but I also have a Bag I was given as a prize for something or other here at Microsoft. Either way, I like something with less pockets and more big, open compartments. Everything gets rolled up and packed in, with all of the wires and charges in small bags my wife made for me. The laptop (and anything I don’t want gate-checked) goes on top or in an outside pouch so I can grab it quickly if I have to gate-check the bag. As much as I can, I try to go in one bag. When I can’t (like this week) I use this bag since it can expand, roll up, crush and even be put away later. It’s super-heavy canvas and worth the price. This allows me to not check a bag.  Journey Logistics The day of the trip, I have everything ready since I’m getting up early. I pack a few small snacks inside a plastic large-mouth water bottle, which protects the snacks and lets me get water in the terminal. I bring along those little powdered drink mixes to add to the water.  At the airport, I make a beeline for the power-outlets. I charge up my laptop and phone, and download all my e-mails so I can work on them off-line in the air. I don’t travel as often as I used to – just every month or so now, so I don’t have a membership to an airline club. If I travel much more, I’ll invest in one again – they are WELL worth the money, for the wifi, food and quiet if for nothing else.  I print out my logistics on paper and put that in my pocket – flight numbers, hotel addresses and phones for everything. That way if I have to make a change, I don’t have to boot up anything or even have power to be able to roll with the punches if things change.  Working While Away  While I’m away I realize I’m going to be swamped with things at the conference or with my clients. So I turn on Out-Of-Office notifications to let people know I won’t be as responsive, and I keep my Outlook calendar up to date so my co-workers know what I’m up to. I even update it with hotel and phone info in case they really need to reach me. I share my calendar with my wife so my family knows what I’m doing as well.  I check my e-mail during breaks, but I only respond to them in the evening or early morning at the hotel. I tweet during conferences. The point is to be as present as possible during the event or when I’m at the clients. Both deserve it.  So those are my initial thoughts. I’ll tag Brent Ozar, Brad McGeHee and Paul Randal, and they can tag whomever they wish. Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• CodePlex Daily Summary for Friday, December 31, 2010

  CodePlex Daily Summary for Friday, December 31, 2010Popular ReleasesFree Silverlight & WPF Chart Control - Visifire: Visifire SL and WPF Charts v3.6.6 Released: Hi, Today we are releasing final version of Visifire, v3.6.6 with the following new feature: * TextDecorations property is implemented in Title for Chart. * TitleTextDecorations property is implemented in Axis. * MinPointHeight property is now applicable for Column and Bar Charts. Also this release includes few bug fixes: * ToolTipText property of DataSeries was not getting applied from Style. * Chart threw exception if IndicatorEnabled property was set to true and Too...Windows Weibo all in one for Sina Sohu and QQ: WeiBee V0.1: WeiBee is an all in one Twitter tool, which can update Wei Bo at the same time for websites. It intends to support t.sohu.com, t.sina.com.cn and t.qq.com.cn. If you have WeiBo at SOHU, SINA and QQ, you can try this tool to help you save time to open all the webpages to update your status. For any business opportunity, such as put advertise on China Twitter market, and to build a custom WeiBo tool, please reach my email box qq1800@gmail.com My official WeiBo is http://mediaroom.t.sohu.comStyleCop Compliant Visual Studio Code Snippets: Visual Studio Code Snippets - January 2011: StyleCop Compliant Visual Studio Code Snippets Visual Studio 2010 provides C# developers with 38 code snippets, enhancing developer productivty and increasing the consistency of the code. Within this project the original code snippets have been refactored to provide StyleCop compliant versions of the original code snippets while also adding many new code snippets. Within the January 2011 release you'll find 82 code snippets to make you more productive and the code you write more consistent!...WPF Application Framework (WAF): WPF Application Framework (WAF) 2.0.0.2: Version: 2.0.0.2 (Milestone 2): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. Requirements .NET Framework 4.0 (The package contains a solution file for Visual Studio 2010) The unit test projects require Visual Studio 2010 Professional Remark The sample applications are using Microsoft’s IoC container MEF. However, the WPF Application Framework (WAF) doesn’t force you to use the same IoC container in your application. You can use ...eCompany: eCompany v0.2.0 Build 63: Version 0.2.0 Build 63: Added Splash screen & about box Added downloading of currencies when eCompany launched for the first time (must close any bug caused by no currency rate existing) Added corp creation when eCompany launched for the first time (for now, you didn't need to edit the company.xml file manually) You just need to decompress file "eCompany v0.2.0.63.zip" into your current eCompany install directory.SQL Monitor - tracking sql server activities: SQL Monitor 3.0 alpha 8: 1. added truncate table/defrag index/check db functions 2. improved alert 3. fixed problem with alert causing config file corrupted(hopefully)Analysis Services Stored Procedure Project: 1.3.5 Release: This release includes the following fixes and new functionality: Updates to GetCubeLastProcessedDate to work with perspectives Fixes to reports that call Discover functions improving drillthrough functions against perspectives improving ExecuteDrillthroughAndFixColumns logic fixing situation where MDX query calling certain ASSP sprocs which opened external connections caused deadlock to SSAS processing small fix to Partition code when DbColumnName property doesn't exist changes...DocX: DocX v1.0.0.11: Building Examples projectTo build the Examples project, download DocX.dll and add it as a reference to the project. OverviewThis version of DocX contains many bug fixes, it is a serious step towards a stable release. Added1) Unit testing project, 2) Examples project, 3) To many bug fixes to list here, see the source code change list history.Cosmos (C# Open Source Managed Operating System): 71406: This is the second release supporting the full line of Visual Studio 2010 editions. Changes since release 71246 include: Debug info is now stored in a single .cpdb file (which is a Firebird database) Keyboard input works now (using Console.ReadLine) Console colors work (using Console.ForegroundColor and .BackgroundColor)AutoLoL: AutoLoL v1.5.0: Added the all new Masteries Browser which replaces the Quick Open combobox AutoLoL will now attemt to create file associations for mastery (*.lolm) files Each Mastery Build can now contain keywords that the Masteries Browser will use for filtering Changed the way AutoLoL detects if another instance is already running Changed the format of the mastery files to allow more information stored in* Dialogs will now focus the Ok or Cancel button which allows the user to press Return to clo...Paint.NET PSD Plugin: 1.6.0: Handling of layer masks has been greatly improved. Improved reliability. Many PSD files that previously loaded in as garbage will now load in correctly. Parallelized loading. PSD files containing layer masks will load in a bit quicker thanks to the removal of the sequential bottleneck. Hidden layers are no longer made visible on save. Many thanks to the users who helped expose the layer masks problem: Rob Horowitz, M_Lyons10. Please keep sending in those bug reports and PSD repro files!Facebook C# SDK: 4.1.1: From 4.1.1 Release: Authentication bug fix caused by facebook change (error with redirects in Safari) Authenticator fix, always returning true From 4.1.0 Release Lots of bug fixes Removed Dynamic Runtime Language dependencies from non-dynamic platforms. Samples included in release for ASP.NET, MVC, Silverlight, Windows Phone 7, WPF, WinForms, and one Visual Basic Sample Changed internal serialization to use Json.net BREAKING CHANGE: Canvas Session is no longer supported. Use Signed...Catel - WPF and Silverlight MVVM library: 1.0.0: And there it is, the final release of Catel, and it is no longer a beta version!EnhSim: EnhSim 2.2.7 ALPHA: 2.2.7 ALPHAThis release supports WoW patch 4.03a at level 85 To use this release, you must have the Microsoft Visual C++ 2010 Redistributable Package installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=A7B7A05E-6DE6-4D3A-A423-37BF0912DB84 To use the GUI you must have the .NET 4.0 Framework installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51-5ff4-4491-b0e5-b386f32c0992 - Mongoose has bee...Euro for Windows XP: ChangeRegionalSettings 1..0: *Rocket Framework (.Net 4.0): Rocket Framework for Windows V 1.0.0: Architecture is reviewed and adjusted in a way so that I can introduce the Web version and WPF version of this framework next. - Rocket.Core is introduced - Controller button functions revisited and updated - DB is renewed to suite the implemented features - Create New button functionality is changed - Add Question Handling featuresFlickr Wallpaper Rotator (for Windows desktop): Wallpaper Flickr 1.1: Some minor bugfixes (mostly covering when network connection is flakey, so I discovered them all while at my parents' house for Christmas).NoSimplerAccounting: NoSimplerAccounting 6.0: -Fixed a bug in expense category report.NHibernate Mapping Generator: NHibernate Mapping Generator 2.0: Added support for Postgres (Thanks to Angelo)NewLife XCode: XCode v6.5.2010.1223 ????（????v3.5??）: XCode v6.5.2010.1223 ????，??： NewLife.Core ??? NewLife.Net ??? XControl ??? XTemplate ????，??C#?????? XAgent ???? NewLife.CommonEnitty ??????（???，XCode??????） XCode?? ?????????，??????????????????，?????95% XCode v3.5.2009.0714 ??，?v3.5?v6.0???????????????，?????????。v3.5???????????，??????????????。 XCoder ??XTemplate?????????，????????XCode??? XCoder_Src ???????（????XTemplate????），??????????????????New Projects1i2m3i4s5e6r7p: 1i2m3i4s5e6r7pA3 Fashion Web: A complete e-commerce siteAfonsoft Blog - Blog de teste: Blog para teste de desenvolvimento em MySQL ou SQLServer com ASP.NET 3.5AnyGrid for ASP.NET MVC: Which grid component should you use for your ASP.NET MVC project? How about all of them? AnyGrid makes it easy to switch between grid implementations, allowing a single action to, e.g., use two different grids for desktop and mobile views. It also supports DataAnnnotations.BizTalk Map Test Framework: The Map Test Framework makes it easier for BizTalk developers to test their maps. You'll no longer have to maintain a whole bunch of XML files for your tests. The use of template files and xpath queries to perform tests will increase your productivity tremendously.BlogResult.NET: A simple Blogging starter kit using S#harp Architecture. This project was originally course material sample code for an MVC class, but we decided to open source it and make it available to the community.Caro: Code demo caro game.Ecozany Skin for DotNetNuke: This Ecozany package contains three sample skins and a collection of containers for use in your DotNetNuke web sites.Enhanced lookup field: Enhanced lookup field makes it easier for end users to create filters. You'll no longer have to use a custom field or javascript to have a parent child lookup for example. It's developed in C#. - Parent/multiple child lookups - Advanced filters options - Easy to usejobglance: This is job siteMaxLeafWeb_K3: MaxLeafWeb_K3Miage Kart: Projet java M1msystem: MVC. Net web systemNetController: Controle sem teclas de direção, usando acelerômentro e .NET micro Framework.Pencils - A Blog Site framework: Another Blog site frameworkPICTShell: PICT is an efficient way to design test cases and test configurations for software systems. PICT Shell is the GUI for PICT.Portal de Solicitação de Serviços: O Portal de Solicitação de Serviços é uma solução que atende diversas empresas prestadores de serviços. Inicialmente desenvolvido para atender empresa de informática, mas o objetivo é que com a publicação do fonte, ele seja extendido à diversos tipos de prestadoras.Runery: Runery RSPSsCut4s: sCut4sSumacê Jogava Caxangá?: sumace makes it easier for gamers to play. You'll no longer have to play. It's developed in XNA.Supply_Chain_FInance: Supply Chain Finance thrives these years all over the world. In exploring the inner working mechanism ,we can sought to have a way to embed an information system in it. We develop the system to suit the domesticated supply chain finace .TestAmir: ??? ????? ??? ???The Cosmos: School project on a SOA based system (Loan system)Time zone: A c# library for manage time changes for any time zone in the world. Based on olson database.Validate: Validate is a collection of extension methods that let you add validations to any object and display validations in a user/developer friendly format. Its an extremely light weight validation framework with a zero learning curve.Windows Phone 7 Silverlight ListBox with CheckBox Control: A Windows Phone 7 ListBox control, providing CheckBoxes for item selection when in "Choose State" and no CheckBoxes in "Normal State", like the built-in Email app, with nice transition. To switch between states, set the "IsInChooseState" property. The control inherits ListBox.XQSOFT.WF.Designer: this is workflow designerzhanghai: my test project

  Read the article

• LightDM will not start after stopping it

  - by Sweeters

  I am running Ubuntu 11.10 "Oneiric Ocelot", and in trying to install the nvidia CUDA developer drivers I switched to a virtual terminal (Ctrl-Alt-F5) and stopped lightdm (installation required that no X server instance be running) through sudo service lightdm stop. Re-starting lightdm with sudo service lightdm start did not work: A couple of * Starting [...] lines where displayed, but the process hanged. (I do not remember at which point, but I think it was * Starting System V runlevel compatibility. I manually rebooted my laptop, and ever since booting seems to hang, usually around the * Starting anac(h)ronistic cron [OK] log line (not consistently at that point, though). From that point on, I seem to be able to interact with my system only through a tty session (Ctrl-Alt-F1). I've tried purging and reinstalling both lightdm and gdm, as well as selecting both as the default display managers (through sudo dpkg-reconfigure [lightdm / gdm] or by manually editing /etc/X11/default-display-manager) through both apt-get and aptitude (that shouldn't make a difference anyway) after updating the packages, but the problem persists. Some of the responses I'm getting are the following: After running sudo dpkg-reconfigure lightdm (but not ... gdm) I get the following message: dpkg-maintscript-helper:warning: environment variable DPKG_MATINSCRIPT_NAME missing dpkg-maintscript-helper:warning: environment variable DPKG_MATINSCRIPT_PACKAGE missing After trying sudo service lightdm start or sudo start lightdm I get to see the boot loading screen again but nothing changes. If I go back to the tty shell I see lightdm start/running, process <num> but ps -e | grep lightdm gives no output. After trying sudo service gdm start or sudo starg gdm I get the gdm start/running, process <num> message, and gdm-binary is supposedly an active process, but all that happens is that the screen blinks a couple of times and nothing else. Other candidate solutions that I'd found on the web included running startx but when I try that I get an error output [...] Fatal server error: no screens found [...]. Moreover, I made sure that lightdm-gtk-greeter is installed but that did not help either. Please excuse my not including complete outputs/logs; I am writing this post from another computer and it's hard to manually copy the complete logs. Also, I've seen several posts that had to do with similar problems, but either there was no fix, or the one suggested did not work for me. In closing: Please help! I very much hope to avoid re-installing Ubuntu from scratch! :) Alex @mosi I did not manage to fix the NVIDIA kernel driver as per your instructions. I should perhaps mention that I'm on a Dell XPS15 laptop with an NVIDIA Optimus graphics card, and that I have bumblebee installed (which installs nvidia drivers during its installation, I believe). Issuing the mentioned commands I get the following: ~$uname -r 3.0.0-12-generic ~$lsmod | grep -i nvidia nvidia 11713772 0 ~$dmesg | grep -i nvidia [ 8.980041] nvidia: module license 'NVIDIA' taints kernel. [ 9.354860] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.354864] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.354868] nvidia 0000:01:00.0: enabling device (0006 -> 0007) [ 9.354873] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9.354879] nvidia 0000:01:00.0: setting latency timer to 64 [ 9.355052] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 280.13 Wed Jul 27 16:53:56 PDT 2011 Also, running aptitude search nvidia gives me the following: p nvidia-173 - NVIDIA binary Xorg driver, kernel module a p nvidia-173-dev - NVIDIA binary Xorg driver development file p nvidia-173-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-173-updates-dev - NVIDIA binary Xorg driver development file p nvidia-96 - NVIDIA binary Xorg driver, kernel module a p nvidia-96-dev - NVIDIA binary Xorg driver development file p nvidia-96-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-96-updates-dev - NVIDIA binary Xorg driver development file p nvidia-cg-toolkit - Cg Toolkit - GPU Shader Authoring Language p nvidia-common - Find obsolete NVIDIA drivers i nvidia-current - NVIDIA binary Xorg driver, kernel module a p nvidia-current-dev - NVIDIA binary Xorg driver development file c nvidia-current-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-current-updates-dev - NVIDIA binary Xorg driver development file i nvidia-settings - Tool of configuring the NVIDIA graphics dr p nvidia-settings-updates - Tool of configuring the NVIDIA graphics dr v nvidia-va-driver - v nvidia-va-driver - I've tried manually installing (sudo aptitude install <package>) packages nvidia-common and nvidia-settings-updates but to no avail. For example, sudo aptitude install nvidia-settings-updates returns the following log: Reading package lists... Building dependency tree... Reading state information... Reading extended state information... Initializing package states... Writing extended state information... No packages will be installed, upgraded, or removed. 0 packages upgraded, 0 newly installed, 0 to remove and 83 not upgraded. Need to get 0 B of archives. After unpacking 0 B will be used. Writing extended state information... Reading package lists... Building dependency tree... Reading state information... Reading extended state information... Initializing package states... Writing extended state information... The same happens with the Linux headers (i.e. I cannot seem to be able to install linux-headers-3.0.0-12-generic). The output of aptitude search linux-headers is as follows: v linux-headers - v linux-headers - v linux-headers-2.6 - i linux-headers-2.6.38-11 - Header files related to Linux kernel versi i linux-headers-2.6.38-11-generic - Linux kernel headers for version 2.6.38 on i A linux-headers-2.6.38-8 - Header files related to Linux kernel versi i A linux-headers-2.6.38-8-generic - Linux kernel headers for version 2.6.38 on v linux-headers-3 - v linux-headers-3.0 - v linux-headers-3.0 - i A linux-headers-3.0.0-12 - Header files related to Linux kernel versi p linux-headers-3.0.0-12-generic - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-generic- - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-server - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-virtual - Linux kernel headers for version 3.0.0 on p linux-headers-generic - Generic Linux kernel headers p linux-headers-generic-pae - Generic Linux kernel headers v linux-headers-lbm - v linux-headers-lbm - v linux-headers-lbm-2.6 - v linux-headers-lbm-2.6 - p linux-headers-lbm-3.0.0-12-gene - Header files related to linux-backports-mo p linux-headers-lbm-3.0.0-12-gene - Header files related to linux-backports-mo p linux-headers-lbm-3.0.0-12-serv - Header files related to linux-backports-mo p linux-headers-server - Linux kernel headers on Server Equipment. p linux-headers-virtual - Linux kernel headers for virtual machines @heartsmagic I did try purging and reinstalling any nvidia driver packages, but it did not seem to make a difference, My xorg.conf file contains the following: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 280.13 ([email protected]) Wed Jul 27 17:15:58 PDT 2011 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" HorizSync 28.0 - 33.0 VertRefresh 43.0 - 72.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection

  Read the article

• Visiting the Emtel Data Centre

  Back in February at the first event of the Emtel Knowledge Series (EKS) I spoke to various people at Emtel about their data centre here on the island. I was trying to see whether it would be possible to arrange a meeting over there for a selected group of our community members. Well, let's say it like this... My first approach wasn't that promising and far from successful but during the following months there were more and more occasions to get in touch with the "right" contact persons at Emtel to make it happen... Setting up an appointment and pre-requisites The major improvement came during a Boot Camp for Windows Phone 8.1 App development organised by Microsoft Indian Ocean Islands in cooperation with Emtel at the Emtel World, Ebene. Apart from learning bits and pieces regarding Universal Apps I took the opportunity to get in touch with Arvin Lockee, Sales Executive - Data, during our lunch break. And this really kicked off the whole procedure. Prior to get access to the Emtel data centre it is requested that you provide full name and National ID of anyone going to visit. Also, it should be noted that there was only a limited amount of seats available. Anyways, packed with this information I posted through the usual social media channels. Responses came in very quickly and based on First-come, first-serve (FCFS) principle I noted down the details and forwarded them to Emtel in order to fix a date and time for the visit. In preparation on our side, all attendees exchanged contact details and we organised transport options to go to the data centre in Arsenal. The day before and on the day of our meeting, Arvin send me a reminder to check whether everything is still confirmed and ready to go... Of course, it was! Arriving at the Emtel Data Centre As I'm coming from Flic En Flac towards the North, we agreed that I'm going to pick up a couple of young fellows near the old post office in Port Louis. All went well, except that Sean eventually might be living in another time zone compared to the rest of us. Anyway, after some extended stop we were complete and arrived just in time in Arsenal to meet and greet with Ish and Veer. Again, Emtel is taking access procedures to their data centre very serious and the gate stayed close until all our IDs had been noted and compared to the list of registered attendees. Despite having a good laugh at the mixture of old and new ID cards it was a straight-forward processing. The ward was very helpful and guided us to the waiting area at the entrance section of the building. Shortly after we were welcomed by Kamlesh Bokhoree, the Data Centre Officer. He gave us brief introduction into the rules and regulations during our visit, like no photography allowed, not touching the buttons, and following his instructions through the whole visit. Of course! Inside the data centre Next, he explained us the multi-factor authentication system using a combination of bio-metric data, like finger print reader, and "classic" pin panel. The Emtel data centre provides multiple services and next to co-location for your own hardware they also offer storage options for your backup and archive data in their massive, fire-resistant vault. Very impressive to get to know about the considerations that have been done in choosing the right location and how to set up the whole premises. It should also be noted that there is 24/7 CCTV surveillance inside and outside the buildings. Strengths of the Emtel TIER 3 Data Centre, Mauritius Finally, we were guided into the first server room. And wow, the whole setup is cleverly planned and outlined in the architecture. From the false floor and ceilings in order to provide optimum air flow, over to the separation of cold and hot aisles between the full-size server racks, and of course the monitored air conditions in order to analyse and watch changes in temperature, smoke detection and other parameters. And not surprisingly everything has been implemented in two independent circuits. There is a standardised classification for the construction and operation of data centres world-wide, and the Emtel's one has been designed to be a TIER 4 building but due to the lack of an alternative power supplier on the island it is officially registered as a TIER 3 compliant data centre. Maybe in the long run there might be a second supplier of energy next to CEB... time will tell. Luckily, the data centre is integrated into the National Fibre Optic Gigabit Ring and Emtel already connects internationally through diverse undersea cable routes like SAFE & LION/LION2 out of Mauritius and through several other providers for onwards connectivity. The data centre is part of the National Fibre Optic Gigabit Ring and has redundant internet connectivity onwards. Meanwhile, Arvin managed to join our little group of geeks and he supported Kamlesh in answering our technical questions regarding the capacities and general operation of the data centre. Visiting the NOC and its dedicated team of IT professionals was surely one of the visual highlights. Seeing their wall of screens to monitor any kind of activities on the data lines, the managed servers and the activity in and around the building was great. Even though I'm using a multi-head setup since years I cannot keep it up with that setup... ;-) But I got a couple of ideas on how to improve my work spaces here at the office. Clear advantages of hosting your e-commerce and mobile backends locally After the completely isolated NOC area we continued our Q&A session with Kamlesh and Arvin in the second server room which is dedictated to shared environments. On first thought it should be well-noted that there is lots of space for full-sized racks and therefore co-location of your own hardware. Actually, given the feedback that there will be upcoming changes in prices the facilities at the Emtel data centre are getting more and more competitive and interesting for local companies, especially small and medium enterprises. After seeing this world-class infrastructure available on the island, I'm already considering of moving one of my root servers abroad to be co-located here on the island. This would provide an improved user experience in terms of site performance and latency. This would be a good improvement, especially for upcoming e-commerce solutions for two of my local clients. Later on, we actually started the conversation of additional services that could be a catalyst for the local market in order to attract more small and medium companies to take the data centre into their evaluations regarding online activities. Until today Emtel does not provide virtualised server environments but there might be ongoing plans in the future to cover this field as well. Emtel is a mobile operator and internet connectivity provider in the first place, entering a market of managed and virtualised server infrastructures including capacities in terms of cloud storage and computing are rather new and there is a continuous learning curve at Emtel, too. You cannot just jump into a new market and see how it works out... And I appreciate Emtel's approach towards a solid fundament and then building new services on top of that. Emtel as a future one-stop-shop service provider for all your internet and telecommunications needs. Emtel's promotional video about their TIER 3 data centre in Arsenal, Mauritius More details are thoroughly described in Emtel's brochure of their data centre. Check out their PDF document here. Thanks for this opportunity Visiting and walking through the Emtel data centre for more than 2 hours was a great experience. As representative of the Mauritius Software Craftsmanship Community (MSCC) I would like to thank anyone at Emtel involved in the process of making it happen, and especially to Arvin Lockee and Kamlesh Bokhoree for their time and patience in explaining the infrastructure and answering all the endless questions from our members. Thank You!

  Read the article

• Windows 8.1 Will Start Encrypting Hard Drives By Default: Everything You Need to Know

  - by Chris Hoffman

  Windows 8.1 will automatically encrypt the storage on modern Windows PCs. This will help protect your files in case someone steals your laptop and tries to get at them, but it has important ramifications for data recovery. Previously, “BitLocker” was available on Professional and Enterprise editions of Windows, while “Device Encryption” was available on Windows RT and Windows Phone. Device encryption is included with all editions of Windows 8.1 — and it’s on by default. When Your Hard Drive Will Be Encrypted Windows 8.1 includes “Pervasive Device Encryption.” This works a bit differently from the standard BitLocker feature that has been included in Professional, Enterprise, and Ultimate editions of Windows for the past few versions. Before Windows 8.1 automatically enables Device Encryption, the following must be true: The Windows device “must support connected standby and meet the Windows Hardware Certification Kit (HCK) requirements for TPM and SecureBoot on ConnectedStandby systems.”  (Source) Older Windows PCs won’t support this feature, while new Windows 8.1 devices you pick up will have this feature enabled by default. When Windows 8.1 installs cleanly and the computer is prepared, device encryption is “initialized” on the system drive and other internal drives. Windows uses a clear key at this point, which is removed later when the recovery key is successfully backed up. The PC’s user must log in with a Microsoft account with administrator privileges or join the PC to a domain. If a Microsoft account is used, a recovery key will be backed up to Microsoft’s servers and encryption will be enabled. If a domain account is used, a recovery key will be backed up to Active Directory Domain Services and encryption will be enabled. If you have an older Windows computer that you’ve upgraded to Windows 8.1, it may not support Device Encryption. If you log in with a local user account, Device Encryption won’t be enabled. If you upgrade your Windows 8 device to Windows 8.1, you’ll need to enable device encryption, as it’s off by default when upgrading. Recovering An Encrypted Hard Drive Device encryption means that a thief can’t just pick up your laptop, insert a Linux live CD or Windows installer disc, and boot the alternate operating system to view your files without knowing your Windows password. It means that no one can just pull the hard drive from your device, connect the hard drive to another computer, and view the files. We’ve previously explained that your Windows password doesn’t actually secure your files. With Windows 8.1, average Windows users will finally be protected with encryption by default. However, there’s a problem — if you forget your password and are unable to log in, you’d also be unable to recover your files. This is likely why encryption is only enabled when a user logs in with a Microsoft account (or connects to a domain). Microsoft holds a recovery key, so you can gain access to your files by going through a recovery process. As long as you’re able to authenticate using your Microsoft account credentials — for example, by receiving an SMS message on the cell phone number connected to your Microsoft account — you’ll be able to recover your encrypted data. With Windows 8.1, it’s more important than ever to configure your Microsoft account’s security settings and recovery methods so you’ll be able to recover your files if you ever get locked out of your Microsoft account. Microsoft does hold the recovery key and would be capable of providing it to law enforcement if it was requested, which is certainly a legitimate concern in the age of PRISM. However, this encryption still provides protection from thieves picking up your hard drive and digging through your personal or business files. If you’re worried about a government or a determined thief who’s capable of gaining access to your Microsoft account, you’ll want to encrypt your hard drive with software that doesn’t upload a copy of your recovery key to the Internet, such as TrueCrypt. How to Disable Device Encryption There should be no real reason to disable device encryption. If nothing else, it’s a useful feature that will hopefully protect sensitive data in the real world where people — and even businesses — don’t enable encryption on their own. As encryption is only enabled on devices with the appropriate hardware and will be enabled by default, Microsoft has hopefully ensured that users won’t see noticeable slow-downs in performance. Encryption adds some overhead, but the overhead can hopefully be handled by dedicated hardware. If you’d like to enable a different encryption solution or just disable encryption entirely, you can control this yourself. To do so, open the PC settings app — swipe in from the right edge of the screen or press Windows Key + C, click the Settings icon, and select Change PC settings. Navigate to PC and devices -> PC info. At the bottom of the PC info pane, you’ll see a Device Encryption section. Select Turn Off if you want to disable device encryption, or select Turn On if you want to enable it — users upgrading from Windows 8 will have to enable it manually in this way. Note that Device Encryption can’t be disabled on Windows RT devices, such as Microsoft’s Surface RT and Surface 2. If you don’t see the Device Encryption section in this window, you’re likely using an older device that doesn’t meet the requirements and thus doesn’t support Device Encryption. For example, our Windows 8.1 virtual machine doesn’t offer Device Encryption configuration options. This is the new normal for Windows PCs, tablets, and devices in general. Where files on typical PCs were once ripe for easy access by thieves, Windows PCs are now encrypted by default and recovery keys are sent to Microsoft’s servers for safe keeping. This last part may be a bit creepy, but it’s easy to imagine average users forgetting their passwords — they’d be very upset if they lost all their files because they had to reset their passwords. It’s also an improvement over Windows PCs being completely unprotected by default.     

  Read the article

< Previous Page | 422 423 424 425 426 427 428 429 430 431 432 433  | Next Page >