Search Results

Search found 15129 results on 606 pages for 'orientation changes'.

Page 468/606 | < Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >

  • Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

    - by Biohazard
    I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

    Read the article

  • Juniper SSG20 IP settings for email server

    - by codemonkie
    We have 5 usable external static IP addresses leased by our ISP: .49 to .53, where .49 is assigned to the Juniper SSG20 firewall and NATed for 172.16.10.0/24 .50 is assigned to a windows box for web server and domain controller .51 is assigned to another windows box with exchange server (domain: mycompany1.com) mx record is pointing to 20x.xx.xxx.51 Currently there is a policy set for all SMTP incoming traffic addressed to .51 forward to the NATed address of the exchange server box (private IP: 172.16.10.194). We can send and receive emails for both internal and external, but the gmail is saying mails from mycomany1.com is not sent from the same IP as the mx lookup however is from 20x.xx.xxx.49: Received-SPF: neutral (google.com: 20x.xx.xxx.49 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=20x.xx.xxx.49; Authentication-Results: mx.google.com; spf=neutral (google.com: 20x.xx.xxx.49 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] and the mx record in global dns space as well as in the domain controller .50 for mail.mycompany1.com is set to 20x.xx.xxx.51 My attempt to resolve the above issue is to Update the mx record from 20x.xx.xxx.51 to 20x.xx.xxx.49 Create a new VIP for SMTP traffic addressed to 20x.xx.xxx.49 to forward to 172.16.10.194 After my changes incoming email stopped working, I believe it has something to do with the Juniper setting that SMTP addressed to .49 is not forwarded to 172.16.10.194 Also, I have been wondering is it mandatory to assign an external static IP address to the Juniper firewall? Any helps appreciated. TIA

    Read the article

  • Routing and authenticating all access through squid

    - by Knight Samar
    Hi, I want to route all Internet access in my network through a Squid proxy server and authenticate and log all users. I want this to be a client-independent setting so that no one needs to do anything on their browsers or machines. I have set my network gateway as the proxy server so that all traffic will be sent to it. I have done this using options in DHCP server. Now I tried using squid as a transparent proxy, but then it won't authenticate in that mode. I tried using iptables to route all traffic to port 3128 but it won't popup the authentication dialog box from SQUID. I tried telling DHCP to give WPAD to all clients by placing a WPAD file on a webserver containing the following for automatic proxy configuration on clients: Changes in dhcpd.conf option wpad code 252 =test; option wpad "\n\000"; option wpad "http://192.168.1.5/wpad.dat\n"; The WPAD file: function FindProxyForURL(url,host) { return "PROXY squid-server-ip-address:3128 ; DIRECT "; } But the browsers (different versions of Firefox and IE) seem to ignore it. :( What should I do ?

    Read the article

  • Understanding Microsoft Word Formatting Behavior. Does anyone?

    - by deemer
    This isn't a question about how to do something (well, not directly), but rather an inquiry to see if anyone understands why MS Word behaves the way it does with respect to formatting from a design perspective. This is also admittedly a rant about Word. This is a question that has plagued me, well, every time I open a document in Word, and covers a lot of individual topics, so I'll restrict the discussion here to two concrete behaviors that baffle me. 1) Backspacing over whitespace changes the format of preceding text. This seems to most often occur when the preceding text is a header or list number. The strangest thing about this is the new format of the changed text usually doesn't appear anywhere else in the document. 2) Numbered lists count almost at random. I am working on a document today where the list numbers count as follows: 1, 2, 2, 3, 3. The lettering in the sublists go like this 1: a, 2: a, 2: b c d, 3: e f g, 3: a. Clicking on each number or letter highlights the other numbers or letters that Word thinks it is related to, which are scattered around the document pretty heavily. Attempts to renumber the list have so far proven fruitless, as Word seems to maintain these associations through clipboard copies, etc. Why could this even happen?

    Read the article

  • exim4 seem to stop listening

    - by trakos
    Hey, I have a strange problem with my exim4 configuration. I have a dedicated server running debian for quite a long time now, but I'm not really using it actively recently, so everything just worked due to lack of changes ;) However, recently, my exim4 smtp stopped answering on port 25. It does not respond through localhost, as well - even though it's set to listen on any interface available. Some things I've checked: ks:/home/trakos/Maildir/new# netstat -ap | grep exim tcp 0 0 *:smtp : LISTEN 12521/exim4 ks:/home/trakos/Maildir/new# exiwhat 12521 daemon: -q30s, listening for SMTP on port 25 (IPv4) ks:/home/trakos/Maildir/new# cat /var/log/exim4/rejectlog ks:/home/trakos/Maildir/new# cat /var/log/exim4/paniclog The queue is set for 30s only because I was running it in a non-daemon mode to see any output. Strangely enough, no suspicious output is given, netstat even shows it is listening on port 25, but still trying to telnet to it times out. The only things that may have changed recently are: I've got second IP for my server I remember that few days ago my spamassasin crashed, and I've started it up again So yeah, I'm really clueless about this one now :P I mean, I don't even know what could be failing here. Could someone give me some ideas what should I check next? PS: it has uptime of 442 days, so I haven't really tried rebooting it yet ^^

    Read the article

  • Simple, centralized user management on a small LAN - NIS or LDAP?

    - by einpoklum
    I'm setting up a small LAN for my team. It will, for all intents and purposes, not be connected to any external networks. I would it to have centralized control of user accounts (at least, I think I'd like that; I'm also considering using puppet, so theoretically I could just push /etc/passwd changes, or something). The number of machines is fixed, but not very small. Mostly they're 'attached' to a single user, but sometimes people work remotely on someone else's box; and there are a couple of servers. I've read this question, but my scenario is much simpler (even simpler than in this question) and I'd like to do something (relatively) quick, with not much hassle, but not a dirty totally-insecure hack. Is NIS relevant for my scenario? If not, what's the most hassle-free way to set up LDAP (or LDAP+Kerberos) to achieve the same? Notes: I have no experience with setting up either NIS or LDAP. We use Debian-flavored Linux distributions, mainly Kubuntu 12.04 (not my choice, but that's the way it is).

    Read the article

  • Rendering a frame is producing noise from speakers in Windows and Linux

    - by Robber
    When any hardware accelerated application is rendering a frame (or many of them) a very short noise is coming from my speakers. This can be a game, a WebGL application or XBMC. When the application/game is rendering many frames per second (like most of them do) the noise is a continuous buzzing that gets higher pitched with higher framerates. This applies to Linux and Windows, so I'd assume it's a hardware problem. The current hardware in the PC is: CPU: Core2Quad Q9550 GPU: Radeon HD 5770 RAM: 2x2GB DDR2 Motherboard: Asus P5QLD PRO PSU: be quiet! Pure Power 530W Screen and speakers: Old 720p LCD TV connected via VGA and aux cable Muting the TV stops the noise, muting Windows doesn't. I tried replacing the PSU first (used a Tagan 700W PSU before) because I thought it was a power problem. It wasn't. I tried replacing the motherboard (used a ASUS P5B SE before) next because I thought it was a sound card problem. It wasn't. I tried the GPU in a different PC because I thought it was a broken graphics card. It worked perfectly fine in the other PC. I thought it might be interference, but moving the audio cable around changes absolutely nothing. I tried using an HDMI cable instead and that did work, but is not an option since my TV has only one HDMI input and I need that for my PS3.

    Read the article

  • Is there any way to synchronize AD users with Office 365 but still be able to edit them online?

    - by Massimo
    I'm performing a migration to Office 365 from a third-party mail server (MDaemon); the local Active Directory doesn't include any Exchange server, and never had any. We will need directory synchronization in order to enable users to log on to Office 365 using their domain credentials; but it seems that as soon as you enable directory synchronization, you can't perform any action anymore on Office 365 users: all changes need to be made on the local Active Directory, and then replicated by the synchronization process. For ordinary users with a single e-mail address and standard features, this is not a big problem; but what about users which need an additional address? What if I need to configure some nonstandard setting, like "hide from address list" or a custom mailbox quota? From what I've gathered, the only supported way to do this, as you can't directly edit Office 365 objects anymore after synchronization is enabled, is to extend the local AD schema with Exchange attributes, and then manually edit them (!). Or, you can install at least one local Exchange server, and then use the Exchange administrative tools to configure the required settings. Is this correct or am I missing something? Is there any way to synchronize user accounts and password, but still be able to edit user settings directly in Office 365? If not (everything really needs to be set locally and then synchronized), is there any simpler way to do this than manually editing LDAP attributes or installing a local Exchange server?

    Read the article

  • Spotlight has stopped indexing/returning anything in /Applications

    - by pra
    After a recent kernel panic & restart, Spotlight no longer seems to know anything about the files under my /Applications folder. I used to launch Safari.app, Opera.app, Textedit.app, etc via Spotlight as a matter of routine. Now, I get "No results found" for all of them (except Textedit.app, which launches a demo text editor from a Qt installation). The programs are still there & still launch directly from Finder. I've already run disk utility & verified the disk, no issues. I repaired disk permissions, which made several changes, but to no effect. Is there anything else I can do, short of re-installing MacOS? Update: I already verified that "Applications" was still checked in my Spotlight preferences. It was still returning applications located elsewhere (the Qt textedit sample app), so that shouldn't have been the issue. A few hours later it resolved itself; I guess there's a background process running on some interval.

    Read the article

  • nVidia performance with newer X and newer driver abysmal with Compiz

    - by Nakedible
    I recently upgraded Debian to Xorg 2.9.4 and installed nvidia-glx from experimental, version 260.19.21. This was somewhat of an uphill battle as the dependencies for the experimental nvidia-glx package are still somewhat broken. I got it to work without forcing the installation of any packages and without modifying the packages. However, after the upgrade compiz performance has been abysmal. I am using the desktop wall plugin and switching viewports is really slow - takes a few seconds for each switch. In addition to this, every effect that compiz does, such as zoom animations for icons when launching applications, takes seconds. The viewport switching speed changes relative to the amount of windows on that virtual screen - empty screens switch almost at normal speed, single browser windows work almost decently, but just 4 rxvt terminals slows the switches down to a crawl. My compiz configuration should be pretty basic. Xorg is likewise configured without anything special - the only "custom" configuration is forcing the driver name to be "nvidia". I've fiddled around with the nvidia-settings and compizconfig trying different VSync settings, but none of those helped. My graphics card is: NVIDIA GPU NVS 3100M (GT218) at PCI:1:0:0 (GPU-0). This is laptop GPU that is from the Geforce GTX 200 series. Graphics card performance should naturally be no problem. EDIT: In the end, nothing really worked, and I got really annoyed with the state of compiz and its support in Debian. Many nVidia driver revisions have passed and I am using Gnome 3 now, so I am accepting the best answers to this question even though the issue was not resolved.

    Read the article

  • Korean characters not appearing in Korean Windows XP computer

    - by user13267
    I am using a Korean software (with a partial English interface) in a Korean Version of Windows XP SP 3 However, in parts of the software, even when I change the interface to Korean, Korean letters show up as random characters, as shown here: This is happening at others parts of the software as well, and I am not sure what is the difference between the places where this is happening, and places where this is not happening. For example, a command button where Korean letters are showing up properly is shown below: This software is a video conferencing software and has a chat feature as well. When I type into the chat box, i can see the Korean letters appear properly at my side, but when I press Enter and send the message, it changes into random characters as shown above in the chat box. What could be the issue here? Could it be a missing font in my computer? Since this is a Korean Windows installation I was hoping everything would work properly by default. What can be done here? EDIT 1: I asked some other people who are using this software, and they think that the problem is at my end, and playing around with the Regional and Language Settings might solve the problem. Also, they suggested I install all the language packs related to Korean display. But it looks like all the language packs have been installed, and my location is set to Korea in Regional and Language Settings in Control Panel, and I still have this problem. Also, I have had similar problems with displaying Korean on an English Windows XP computer. This answer suggested some solutions, but I still do not quite understand exactly what I have to do (at that time I had not fixed the problem, as I later on changed the computer). If I follow that answer, what fonts exactly do I need to install?

    Read the article

  • How could I embed formatted XML source in WORD documents?

    - by eckes
    I'm writing a documentation with WORD that contains XML source code (whole files) as examples. The way I'm embedding the currently XML is quite cumbersome and doesn't seem to me as really maintainable: I'm finishing the editing of the document in WORD and create a PDF from it using Acrobat next, I open my XML files (2x input files, 2x generated output files) with IE and print them with the PDF printer supplied by Acrobat now, I open up Acrobat Pro and attach the four XML-PDF files to my original document The problem with that work flow for me is that it involves too much manual labor in order to get the documentation done. What I've tried up to now is not really satisfying for me: converting each XML to PDF and appending them like described above opening the XML files with SCiTE, copy as RTF and paste into Word playing around with the LaTeX packages minted, pygments and listings (I could write the docs with LaTeX too) but found some unsolvable problems in each of these packages I'm searching for a way that produces my documentation more automatic. For example embedding the XML files including formatting of IE (which I find quite readable). The files should be included by reference so that I don't have to paste the XML sources manually every time the XML changes.

    Read the article

  • Outdoor WiFi Mesh Topology vs. Repeaters

    - by IronJaxor
    Here's the current configuration in our organization (which I believe is incorrect): We have a number of Cisco 1500 series AP's (22 in total), that are mounted outdoors to provide seamless WiFi coverage over a large area. Each AP however has its own physical ethernet connection back to the WLC (All the AP's are marked as Root AP's). They are all broadcasting the same SSID. We have tried to stagger the channel selection but because there are only three non-overlapping channels to choose from, and in some areas the density of AP's is quite high, there is multiple places of channel interference. With this configuration we experience 100-150 disconnects from clients every day. (Our clients are mobile so they move throughout the coverage area constantly). My idea is to switch the AP's to the same channel thereby forming a wireless mesh, use the built in functionality of the 1500 series to use 802.11a as the backhaul, designate one or two AP's as root AP's and wire them back to the WLC. Thereby forming a WiFi mesh, which if I'm not mistaken is the point of the 1500 series in the first place! I am however completely new at WiFi networks and wondering if I am simply mistaken in what I believe my proposed changes will enable, or if there is a better way to tackle the WiFi topology.

    Read the article

  • Home Network Stopped Working

    - by James
    I have a home network where a machine running Windows 7 Ultimate N acts as a central hub for other devices to access media. This has been running for around 2 years now and there has been no recent configuration changes. The machine has a static IP address (192.168.0.3), which also has not been changed. A few laptops, Sonos music system and mobiles are using the machine for music/video mostly. Additionally, post 3389 was also open for RDP. I used a no-ip agent to map a hostname so I could RDP to the machine from the internet. As of yesterday when I try to ping the machine, I get PING:Transmit Failed, General Error I noticed however, the IP it is pinging is 0.0.2.233. All shares etc are no longer functioning including RDP. On the machine itself, an IP config shows like nothing has changed. It still shows the expected IP. If I ping itself from its hostname, I get the same error as above. machine has been rebooted, the router has been also. Any ideas where to even start on this?

    Read the article

  • Microsoft Deployment Toolkit 2012 Error

    - by Jacob Schaer
    I just started with MDT2012 recently in hopes of eventually getting away with using Ghost to deploy all of our department computers. When I test deploy in VirtualBox, it deploys the OS properly, but stops because of a network driver failure (it gets the "could not allocate resources" issue). On physical hardware (Latitude E6500, Optiplex 980, and an older Latitude) it gets through the multicast and stops immediately after with: "Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information" I've looked at the logs and never see anything really of note. Originally I was using DriverPacks from DriverPacks.net, but thinking it was a driver issue, I switched over to using Dell's cab driver packs. Still the same issue. I check and it did the HDD is all fine - it was properly partitioned, set to bootable, and was loaded with all the proper OS installer files. I'm using a flash drive to do the install - when I make changes to the deployment share I rebuild and copy the ISO to the drive, then use YUMI multiboot to start the ISO (probably irrelevant).

    Read the article

  • I have bought a custom domain and am using it with Gmail. All My mail is being sent as spam. What can I do?

    - by Leonnears
    A while ago, I purchased my own custom domains for my websites. Before I moved them to Gmail, I just created the e-mails in my CPanel at Bluehost.com and worked from there. When the setup was like that, I could send and receive e-mail fine, and it wouldn't be marked as spam. Now I have moved these custom domains to send and receive e-mails at Gmail using Google apps. I have done everything. I have marked the domains as "Authorized" and I believe that should be enough for the mail I send with these custom e-mails is not send as spam. If it matters, I have configured my iPhone to use these custom domains with it and I'm sending all the e-mail from it. What can I do? I started doing all this today but apparently the DNS changes have already taken place. Is there something I have to do, or is it a matter of waiting 48 hours for my mail to not be marked as spam by other providers yet? EDIT: If I send mail via Gmail itself, the mail is delivered fine. If I use my iPhone however, it gets marked as spam.

    Read the article

  • Upgrading only certain packages via the getdeb repo

    - by intuited
    I'm a bit confused about how getdeb.net works now. The last time I got a package from there was a while ago; at that point the procedure was that you would just download a .deb for each package that you wanted to install/upgrade and then install it using dpkg -i. However the inexorable march of progress has lent its trumpets to this system as well, and getdeb installs are now done via their repo, which is registered with apt in /etc/apt/sources.list.d, after you install a single package that makes the changes to the apt database. I've installed that package, and I've discovered that aptitude dist-upgrade now wants to upgrade a lot of packages on my system that weren't ready for upgrades prior to the installation of the getdeb package. If I rename the file /etc/apt/sources.list.d/getdeb.list to something with a different extension, then do aptitude update && aptitude dist-upgrade, it stops wanting to upgrade packages. So I gather that the default behaviour is now to upgrade all packages to the version available at getdeb. This is not particularly appropriate, since these packages are not as well tested as the officially released versions. Is there a config setting somewhere that will prevent upgrading packages to versions from the getdeb repo unless this action is specifically selected? I'd like to be able to pick and choose what packages are upgraded via getdeb.

    Read the article

  • WAMP running extremely slow on WIndows 7

    - by JavaCake
    After 2 days of tough fight trying to figure out what the problem is with my Windows 7 32-bit machine at work i have nearly given up. The issue is that the pages are loaded extremely slow, the performance is both when accessed locally (127.0.0.1) or from another computer in the intranet. First to explain the system: WAMP version: Apache 2.2.22 – Mysql 5.5.24 – PHP 5.4.3 XDebug 2.1.2 XDC 1.5 PhpMyadmin 3.4.10.1 SQLBuddy 1.3.3 webGrind 1.0 DocumentRoot: Located on network drive MySQL: InnoDB Pages: PHP, MySQL, AJAX etc. So basically the changes i have made in order to get a greater performance: Changed C:\windows\system32\drivers\etc\hosts: 127.0.0.1 localhost 127.0.0.1 127.0.0.1 Modified my.ini: innodb_flush_log_at_trx_commit = 2 Modified httpd.ini: EnableMMAP on EnableSendfile on Modified php.ini: realpath_cache_size= 4m How i measure the performance is the overall loadtime of the page. I run it locally on my Mac OS X machine aswell (MAMP), and typically the frontpage loadtime is 0.06seconds but on the Windows 7 machine it is 6-10seconds. I have verified the loadtime with developertools in Chrome aswell. Furthermore the result is identical in XAMPP.

    Read the article

  • Setup ejabberd with SQL Server 2008

    - by wonster
    Here's what I have got so far. Windows 2008 Server 64 bit. Installed the latest version of ejabberd, ejabberd-2.1.8-windows-installer.exe. The windows service starts up fine but seems ineffective. However, using the start & stop scripts work. I am able to login to the admin page which so far doesn't seem that versatile. Opened up ports 5222, 5226 and 5280 for my workstation to talk to the server. I've got Spark and Jabbear Windows clients to register, login and instant message with multiple accounts using the server. After confirming that I've got the very basics working, I've decided to make use of SQL Server 2008 as the database. Reason? Mainly, I am very comfortable with SQL Server. I can deal with redundancy, failover, data analysis easily. Not sure if ejabberd's built in DB provides all that. Following the instructions from ejabberd's documentation, I setup a system DSN that points to another physical database. The DSN checks out fine. (Tried both Named Pipes and TCP/IP) Modified ejabberd.cfg. Commented line %%{auth_method, internal} and uncommented line {auth_method, odbc} Uncommented and modified {odbc_server, "DSN=ejabberd;UID=somelogin;PWD=somepassword"}. After making these changes, I restarted. No errors are found in the log files. The jabber clients are no longer able to register new accounts. I'm not sure where to look for errors besides the /logs/ folder as I'm new to all this. I am basically stuck here on step 5. Has anyone got this setup to work recently? Some of the posts I've found around are years old and of no help. I can't be the only one setting up ejabberd with MS SQL. Any help would be appreciated!

    Read the article

  • Get Matrox Millenium video card working in Ubuntu 9.10

    - by wcoenen
    I have installed Ubuntu 9.10 on an old PC and it is mostly working, except for some heavy drawing defects that show up whenever I start dragging a window or scrolling inside a window or menu. It looks like the video driver copies the rectangle being moved to the wrong location. I have taken a look in /var/log/Xorg.0.log and the following line shows the detected video card: (--) PCI:*(0:0:8:0) 102b:0519:0000:0000 Matrox Graphics, Inc. MGA 2064W [Millennium] rev 1, Mem@ 0xf9800000/16384, 0xfb000000/8388608, BIOS @0x????????/65536 (==) Using default built-in configuration (30 lines) (==) --- Start of built-in configuration --- Section "Device" Identifier "Builtin Default mga Device 0" Driver "mga" EndSection How do I fix the drawing defects? It turned out that the 24 bit color depth (automatically selected by ubuntu 9.10) was the problem; apparantly the mga driver doesn't handle this well for cards with little memory. I took the following steps to resolve the issue (you can skip the first three steps if you already have a semi-working xorg.conf file): Reboot ubuntu in recovery mode, to get a root console without X running. Run Xorg -configure to generate a xorg.conf.new file Copy the file to /etc/X11/xorg.conf with cp xorg.conf.new /etc/X11/xorg.conf (assuming it didn't exist yet; that's why I generated it) Open the new config file with sudo nano /etc/X11/xorg.conf and make sure the screen section is configured for 16 bit color depth like this: Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 16 Modes "1024x768" EndSubSection EndSection I can't guarantee those were the only important changes I made - I tried a few things in my attempts to create a valid xorg.conf file. But I'm pretty sure that the screen section was the important part.

    Read the article

  • How to connect the virtual networks of vmware guests running on different hosts?

    - by gyrolf
    In a test setup, we are running several virtual machines on a single vmware workstation host. All virtual machines are connected via a "host only" network. This runs fine up to 2 or 3 virtual machines (depending on the host hardware). To allow more virtual machines, we want to use more host machines. Details about the environment and applications: Host PCs are running Windows XP in a corporate intranet. VMware used is Workstation 6.5 Guests are running Windows Server 2003 All guests act as Web Servers One of the guests additionally acts as Windows File server, offering shared folders for the other guests to connect to. Restrictions: VMware guests shall not be visible from the intranet. Changes to the host PC are restricted by corporate policy. In the virtual network, no domain controller exists. All virtual machines are member of the same workgroup. Running the virtual network as NAT is possible. Port forwarding might be used if it does not conflict with ports used by the host PC. Looking for a solution, I found hints about using router or vpn software on the hosts, but without any details how to setup. (I found a similar question Sharing the network between 2 VMware hosts, but the answer was not sufficient for me.)

    Read the article

  • How do you enable webcam support in Facebook for Ubuntu 10.04?

    - by Jonathan
    I think I have finally arrived at an insolvable equation: Chromium v.7 + Ubuntu 10.04 + Sun Java 6 + Webcam + Facebook + Flash 10 = non-functional All of those items listed above are potential points of failure in this situation, and any help narrowing them down would be fantastic. I am simply trying to enable webcame support directly through Facebooks website. Forum searches and the usual googling turn up few posts related to this specific equation. Two of the major suggestions include: 1) Installing the Sun (I refuse to say oracle sob)-provided Java implementation instead of the OpenJDK normally installed in Ubuntu. And yes, after installing it, I did update all my default supports to use the sun commands over the openjdk. 2) Somehow enabling Facebook as a permitted site to access my webcam using Flash settings. I have not been able to explore option 2 because I cannot find a way to adjust the Flash settings in chromium 7. Other factors that do not help include the fact that I am pretty sure facebook changes its webcam interface every 10 seconds just to keep troubleshooters and support personnel on their toes. If anyone has a OTP that informs us of the next shift in the app, a leak would be greatly appreciated!

    Read the article

  • Outlook 2010 PST not indexing

    - by kellyllek
    I've had this problem for months: Outlook is unable to search recent items in the inbox. I was running Outlook 2010 Beta. I've just moved to the Trial version, hoping to solve the issue. I have tons of PST files but one central one I'm mainly concerned with. As of now it seems none of it is indexing. I've been through all the sites and made all the changes; rebuilt the index, changed the name of the PST files, run scanpst, stopped and started the search services, made sure the Windows features under programs and features has the indexing option checked, etc... Status now says 'zero items left to index', and 150,000 have been indexed. I think I have a lot more files than that, and also nothing is showing up on any search. I'm not sure what else to do? Side question. I'm going to be moving out of Outlook. However I have 10Gigs+ of PST files over the years. I want to merge them and make them search-able in the easiest way possible. Any idea on how to do that? Could I even move over to Thunderbird right now and be able to index and search my PST files? Also, Google Desktop won't index Outlook 2010 email either...

    Read the article

  • Scheduled Task unable to create/update any files

    - by East of Nowhere
    I have several tasks in Task Scheduler in Windows Server 2008 SP2 (32-bit) and they all successfully "do their work", except for creating or updating any files on Windows. All the tasks point to simple .cmd files that have the real work but beyond that there's no pattern: some call robocopy with the /LOG option, some call .exe files I wrote that manipulate XML files, some just do stuff with > redirection. With all of them, if I double-click the .cmd file myself, it works fine and the files are created or updated or whatever. If I run it from Task Scheduler (by the schedule or just clicking Run), the task always completes "successfully" but without any of the desired changes to files. I don't see any "unable to create file" errors in Event Viewer either. The tasks do all Run As a specific account, but I have logged in as that account and verified that it has permissions to do everything it needs to. Further details -- Task is set to Run whether user is logged in or not. Configured for: "Windows Vista or Windows Server 2008", there is no other Configured for option available.

    Read the article

  • Lotus Notes 8.0.2 - how to stop all mail showing in customized view

    - by mikolajek
    I am using Lotus Notes 8.0.2 at work and unfortunately the admin restricted changing default folders design. Only little changes are possible (e.g. change columns order) and even them are resetted each time I restart the client. I've created a new view with my desired column order, changed sorting etc. I have only one problem - even though I changed the "view" preference to show messages from the inbox folder only, I keep seeing all mail, regardless of the folder they are placed into. I'm not a Lotus expert and don't really know how to code. Yet, I am surprised as I see in a "simple view" this: uses '(ChangeMeetingType), ...' form AND In folder 'Inbox' And in Formula view only this: SELECT ((Form = "(ChangeMeetingType)") | (Form = "(Return Receipt)") | (Form = "Return Receipt") | (Form = "(ReturnNonReceipt)") | (Form = "ReturnNonReceipt") | (Form = "Memo") | (Form = "Memo") | (Form = "MemoEA") | (Form = "Reply") | (Form = "Reply") | (Form = "Reply With History") | (Form = "Reply With History") | (Form = "To Do") | (Form = "Task") | (Form = "_Document Memo") | (Form = "$DocMemo") | (Form = "Word. Document$Word Memo") | (Form = "WordPro. Document$Word Pro Memo") | (Form = "AlternateMemo")) Therefore, it looks like no folder has been really selected. How can I create a solution to see: Inbox contents only? Just messages, invitations and other "normal" stuff - without calendar entries and contacts?

    Read the article

< Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >