Search Results

Search found 14544 results on 582 pages for 'ssh config'.

Page 473/582 | < Previous Page | 469 470 471 472 473 474 475 476 477 478 479 480  | Next Page >

• OpenSwan (IPSEC) on Fedora 13 with Snow Leopard as a client

  - by sicn

  I recently installed OpenSwan on my Fedora 13 machine. I want to use it to connect with Mac OS X with L2TP over IPSEC, unfortunately I am already stuck on the IPSEC-negotation part. My server is running behind a NATted firewall so my external IP differs from the server's IP. The server has a fixed IP on the network and the same is almost always valid for the clients (they are usually behind a NATted firewall). I installed OpenSwan on Fedora 13 and have following configuration: config setup protostack=netkey nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off nhelpers=0 conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 rekey=no ikelifetime=8h keylife=1h type=transport left=my.servers.external.ip leftprotoport=17/1701 right=%any rightprotoport=17/0 IPSEC starts fine and listens to UDP 500 and 4500. These two ports are opened in the firewall and are forwarded fine to the server. In my /etc/ipsec.secrets file I have my.servers.external.ip %any: "LongAndDifficultPassword" And finally in my sysctl.conf (the redirect-entries are there because OpenSwan was strongly protesting about send/accept_redirects being active) I have net.ipv4.ip_forward = 1 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.all.accept_redirects = 0 Running "ipsec verify" gives me "all greens" (except Opportunistic Encryption Support, which is DISABLED), however, when trying to connect my Mac gives me following in the logs: Nov 1 19:30:28 macbook pppd[4904]: pppd 2.4.2 (Apple version 412.3) started by user, uid 1011 Nov 1 19:30:28 macbook pppd[4904]: L2TP connecting to server 'my.servers.ip.address' (my.servers.ip.address)... Nov 1 19:30:28 macbook pppd[4904]: IPSec connection started Nov 1 19:30:28 macbook racoon[4905]: Connecting. Nov 1 19:30:28 macbook racoon[4905]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Nov 1 19:30:31 macbook racoon[4905]: IKE Packet: transmit success. (Phase1 Retransmit). Nov 1 19:30:38: --- last message repeated 2 times --- Nov 1 19:30:38 macbook pppd[4904]: IPSec connection failed Any ideas at all?

  Read the article

• Firefox 29 - how do I delete history entries visited fewer than x times

  - by lousyuser

  Context: I've been using my Firefox profile for a couple of years now. My history file has become huge, naturally. I got Firefox Sync set up between my main desktop PC and my laptop. HW configs: PC: i5-3450, 8 GB DDR3 RAM, Crucial M4 128 GB SSD laptop: Pentium SU4100, 4 GB DDR3 RAM, WD 5400 rpm HDD Accessing history entries when typing into the Awesome Bar on my desktop takes quite a long time despite the decent config, the laptop is even slower. The experience is quite unresponsive. I figured if I cleared the history up a little bit, I might avoid creating a new profile to speed things up. The question itself: to illustrate: Is there a way to delete all history entries that have been visited fewer than x (let's say 5) times and at the same time the recent visit is fewer than y (let's say 120) days old? afaik the history file is some kind of SQL database, but I'm not really sure how the data is saved, if there's a "safe way" to edit it and what the query to do what I need would look like. Thanks in advance for any help. I kept browsing through previous SuperUser questions to see if I could find relevant information. "In my Firefox profile directory, there is a filed named places.sqlite. Opening it with sqlite reveals (amongst others) the tables moz_places and moz_historyvisits. It seems that moz_historyvisits uses the primary of moz_places to refer to the URLs." As I'm unfamiliar with databases, I don't really understand the way the two tables mentioned in the quote are related. screenshot of a part of the tables I've noticed the visit_count is in a standard format, making it easy to work with. The last_visit_date looks encrypted to my naked eye, but I can't see in which way. Hope that helps, I'm at my wits' end.

  Read the article

• Nginx with http/https - Http seemed redirected to https all the time

  - by dwarfy

  I've this really weird behaviour with my ubuntu 10.04 / nginx 1.2.3 server. Basically I changed the SSL certificates this morning. And ever since it has been behaving weirdly on all apps. Godaddy is reporting that HTTPS/SSL setup is correct. When I try a page it still works correctly when I'm using HTTPS. But when I try using HTTP nginx reports error : 400 Bad Request The plain HTTP request was sent to HTTPS port After looking around on google for hours, I've tried different setup (while originaly my setup was working correctly for longtime, I just renewed certificates) I kindof found a half solution by adding this to my config : error_page 497 $request_uri; The realllly weird thing is that when I use this setup : server { listen 80; server_name john.johnrocks.eu; access_log /home/john/envs/john_prod/nginx_access.log; error_log /home/john/envs/john_prod/nginx_error.log; location / { uwsgi_pass unix:///home/john/envs/john_prod/john.sock; include uwsgi_params; } location /media { alias /home/john/envs/john_prod/johntab/www; } location /adminmedia { alias /home/john/envs/john_prod/johntab/www/adminmedia; } } I still have the same error when using HTTP (while nothing is setup for HTTPS here)?? I'm getting crazy on this !

  Read the article

• Xvnc4 started from xinetd only displays empty gray X screen

  - by scott8035

  I'm attempting to setup an Ubuntu 10.10 box so that anyone can connect to port 5900 and be greeted by the gdm login manager. To do so, I added a vnc entry in /etc/services and I am starting Xvnc4 using this xinetd config file: service vnc { protocol = tcp socket_type = stream wait = no user = nobody server = /usr/bin/Xvnc server_args = -geometry 1000x700 -depth 24 -broadcast -inetd -once -securitytypes None } This kind of works...I can start multiple sessions all to port 5900, and I get an X screen. The problem is that I only get an empty, gray X screen with no applications started. I know when you run vncserver from the command line it will look to your ~/.vnc/ directory for your passwd and xstartup files, and I think what I want to do is put "gnome-session" into the xstart file. However, which xstartup file? The running user is "nobody" who obviously doesn't have a ~/.vnc/ directory. I tried a /root/.vnc/xstartup file and a ~scott/.vnc/xstartup file and it doesn't look like they were even read. I changed the xinetd vnc service so that it would "strace" Xvnc4. I looked thru all the "open" lines and didn't get a clue as to what file it was trying to read for xstart. Can anyone help? I just want a terminal server where the user is presented with a gdm login screen.

  Read the article

• Haproxy not properly passing on X-Forwarded-For header

  - by JesseP

  I have backend web servers that receive requests by way of haproxy-nginx-fastcgi. The web app used to see multiple ip's coming through in the X-Forwarded-For header, chained together with commas (most original IP on the left). At some point in the recent past (just noticed, so not sure what caused it) something changed, and now I'm only seeing a single IP passed in the header to my web application. I've tried with haproxy 1.4.21 and 1.4.22 (recent upgrade) with the same behavior. Haproxy has the forwardfor header set: option forwardfor Nginx fastcgi_params config defines this header to be passed to the app: fastcgi_param HTTP_X_FORWARDED_FOR $http_x_forwarded_for; Anyone have any ideas on what might be going wrong here? EDIT: I just started logging the $http_x_forwarded_for variable in nginx logs, and nginx is only ever seeing a single IP, which shouldn't ever be the case, as we should always see our haproxy ip added in there, right? So, issue must either be in nginx handling of the variable coming in, or haproxy not building it properly. I'll keep digging... EDIT #2: I enabled request and response header logging in HAProxy, and it is not spitting anything out for X-Forwarded-For, which seems very odd: Oct 10 10:49:01 newark-lb1 haproxy[19989]: 66.87.95.74:47497 [10/Oct/2012:10:49:01.467] http service/newark2 0/0/0/16/40 301 574 - - ---- 4/4/3/0/0 0/0 {} {} "GET /2zi HTTP/1.1" O Here are the options i set for this in my frontend: mode http option httplog capture request header X-Forwarded-For len 25 capture response header X-Forwarded-For len 25 option httpclose option forwardfor EDIT #3: It really seems like haproxy is munging the header and just passing on a single one to the backend. This is fairly impacting to our production service, so if anyone has an ideas it would be greatly appreciated. I'm stumped... :(

  Read the article

• Gnome 3 gdm fails to start after preupgrade from fedora 14 to 15

  - by digital illusion

  I'm not able to boot fedora 15 in runlevel 5. After all services start, when the login screen should appear, gdm just show a mouse waiting cursor and keeps restarting itself. From /var/log/gdm/\:0-greeter.log Gtk-Message: Failed to load module "pk-gtk-module" /usr/bin/gnome-session: symbol lookup error: /usr/lib/gtk-3.0/modules/libatk-bridge.so: undefined symbol: atk_plug_get_type /usr/libexec/gnome-setting-daemon: symbol lookup error: /usr/lib/gtk-3.0modules/libatk-bridge.so: undefined symbol: atk_plug_get_type Where should atk_plug_get_type be defined? Edit: Here a better description of the error (system-config-network-gui:2643): Gnome-WARNING **: Accessibility: failed to find module 'libgail-gnome' which is needed to make this application accessible /usr/bin/python: symbol lookup error: /usr/lib/gtk-2.0/modules/libatk-bridge.so: undefined symbol: atk_plug_get_type Why there are still references to gtk2? Did preupgrade fail? Attaching upgrade log... it seems gdm was not added, but it is present in the users and groups list. May 26 11:25:52 sysimage sendmail[1076]: alias database /etc/aliases rebuilt by root May 26 11:25:52 sysimage sendmail[1076]: /etc/aliases: 77 aliases, longest 23 bytes, 795 bytes total May 26 11:46:09 sysimage useradd[1793]: failed adding user 'dbus', data deleted May 26 11:53:37 sysimage systemd-machine-id-setup[2443]: Initializing machine ID from D-Bus machine ID. May 26 11:55:28 sysimage useradd[2835]: failed adding user 'apache', data deleted May 26 11:55:38 sysimage useradd[2842]: failed adding user 'haldaemon', data deleted May 26 11:55:43 sysimage useradd[2848]: failed adding user 'smolt', data deleted May 26 11:57:32 sysimage sendmail[3032]: alias database /etc/aliases rebuilt by root May 26 11:57:32 sysimage sendmail[3032]: /etc/aliases: 77 aliases, longest 23 bytes, 795 bytes total May 26 11:57:46 sysimage groupadd[3066]: group added to /etc/group: name=cgred, GID=482 May 26 11:57:47 sysimage groupadd[3066]: group added to /etc/gshadow: name=cgred May 26 11:57:47 sysimage groupadd[3066]: new group: name=cgred, GID=482 May 26 11:58:42 sysimage useradd[3086]: failed adding user 'ntp', data deleted May 26 12:00:13 sysimage dbus: avc: received policyload notice (seqno=2) May 26 12:15:08 sysimage useradd[4950]: failed adding user 'gdm', data deleted May 26 12:24:39 sysimage dbus: avc: received policyload notice (seqno=3) May 26 12:25:24 sysimage useradd[5522]: failed adding user 'mysql', data deleted May 26 12:25:37 sysimage useradd[5533]: failed adding user 'rpcuser', data deleted May 26 12:26:31 sysimage useradd[5592]: failed adding user 'tcpdump', data deleted Any suggestions before I revert installation to F14?

  Read the article

• App-V Problems After SCCM 2007 SP2 Upgrade

  - by GAThrawn

  We're running an SCCM (MS System Centre Config Manager, successor to SMS) 2007 environment and delivering a number of applications to clients virtualized using App-V 4.5.1. The App-V apps are delivered by SCCM in Download-and-Execute, not streaming mode. The SCCM environment was recently service packed to SCCM 2007 SP2 (amongst other things this gives Win7 support). We also pushed out the updated SCCM clients to our workstations. This seems to have broken file associations for virtual apps for a large number of our users. The users can still open their App-V apps by finding the specific app on their Start Menu and clicking it's icon, but double-clicking an associated file in Explorer, or opening an email attachment gives the "This action is only valid for installed applications" error. There is a Technet blog entry from the App-V team talking about this issue "Upgrade to ConfigMgr 2007 SP2 may break App-V File Type Associations" but running the script there comes back saying "The User Interface option has been updated" but hasn't seemed to fix the problems for any of our users. Unfortunately the Technet blogs don't seem to have comments switched on so you can't see how this has worked out for other people. Anyone else had this problem, have you found any other way to fix it?

  Read the article

• Online resizing of kvm guest root filesystem?

  - by Bittrance

  I have a Linux guest that uses an LVM volume directly as root file system (that is, there is no partition table). libvirt config looks thus: <os> <type arch='x86_64' machine='rhel6.4.0'>hvm</type> <kernel>/boot/vmlinuz-X.Y.Z.el6.x86_64</kernel> <initrd>/boot/initramfs-X.Y.Z.el6.x86_64.img</initrd> <cmdline>console=ttyS0 root=/dev/vda</cmdline> <boot dev='hd'/> </os> <disk type='block' device='disk'> <driver name='qemu' type='raw' cache='none' io='native'/> <source dev='/dev/vg/guest'/> <target dev='vda' bus='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </disk> From inside the guest: $ mount /dev/vda on / type ext4 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) tmpfs on /dev/shm type tmpfs (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) Is it possible to resize the guest's root partition without rebooting the guest? Just doing lvextend on the host and resize2fs from the guest does not seem to be enough.

  Read the article

• Problem setting up HP PhotoSmart C4783

  - by ProfKaos

  I am trying to get several PC's on a network to connect to my client's new wireless printer, the C4783. I initially installed the whole HP 'tsumami of software' the comes with the printer onto my laptop, connected to the printer over USB, and corrected it's networking config. My laptop now also can connect to and print on the printer over the wireless network, as is intended for all PC's. However, when I try and install the HP software on my client's netbook, the HP software cannot find the printer. Firewall was turned off during this time, so doesn't play a role. I tried re-installing all software, but I initially only got a "Repair" or "Uninstall". Choosing Uninstall triggers a lengthy process that ends with a sudden and forceful restart, after which the same "Repair" or "Uninstall" choices are present. Looks like uninstall doesn't. Any suggestions as to how I can begin diagnosing why my laptop has no problem connecting to the printer, but two others do? Wireless is unsecured, and no, nobody has to know where I am right now. :-)

  Read the article

• how to initialize two logical drives on a HP P400i controller without reboot

  - by John

  What I am trying to do is initialize two logical drives on a HP P400i embedded controller without a reboot of the system here my current Array config: array A (SAS, Unused Space: 0 MB) logicaldrive 1 (17.9 GB, RAID 5, OK) logicaldrive 2 (17.9 GB, RAID 5, OK) logicaldrive 3 (75.9 GB, RAID 5, OK) logicaldrive 4 (25.0 GB, RAID 5, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 72 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 72 GB, OK) physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 72 GB, OK) array B (SAS, Unused Space: 0 MB) logicaldrive 5 (99 MB, RAID 0, OK) logicaldrive 6 (68.2 GB, RAID 0, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 72 GB, OK) windows 2003 machine running the HpCISs2.sys driver version 6.20.0.32 . I have the ACU and ACU CLI tools installed version 8.28.13.0, P400i firmware version 2.74 . Now what I'd like to do is removes the physical drive 1I:1:4 and delete the two logical drives in array B. then insert a new drive in to bay 4 that contains two new logical drives and have them show up in array B again. So far after I remove the drive and delete the failed logical drives, I insert the new drive and run HPacucli rescan. I get the new drive to show up as unassinged physical drive but I cant figure out now to "for lack of a better word" mount the 2 logical drives on the new unassinged disk. If I reboot the system the array controller picks up the new fourth drive and creates Array B with the drives without problem but I'd really like to not have to reboot the server. Any ideas?

  Read the article

• Why is apache serving the default?

  - by Matt

  I keep adding more vhosts and enabling them but all the sites always do to the default vhost in sites-available here is what the default kind of looks like with me only changing the ip for security reasons <VirtualHost 167.889.88.88:80> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> and here is my other which i named some-site.net <VirtualHost *:80> ServerName some-site.net DocumentRoot "/var/www/vhosts/somesite.com/http/" <Directory "/var/www/vhosts/somesite.com/http/"> AllowOverride all Options -MultiViews </Directory> </VirtualHost> and it turned on my this command sudo a2ensite some-site.net Enabling site some-site.net. Run '/etc/init.d/apache2 reload' to activate new configuration! then i reloaded /etc/init.d/apache2 reload * Reloading web server config apache2 ...done. but when i visit the url some-site.net i get the index page that is for the default vhost...what am i doing wrong

  Read the article

• pgpoolAdmin keeps going straight back to it's login page

  - by user705142

  I'm trying to run pgpoolAdmin through nginx - it seems to be working properly, at least initially. I've gone through the initial set-up, which works fine, but now after logging in every link takes me straight back to the login page. It also shows japanese text instead of english, despite picking english in the installation. It seems to me just as if it was unable to save any user data, session information etc. I have javascript/cookies enabled, so it's not that. The ownership of the folder is nginx, and so too is pgmgt.conf.php, so it shouldn't be a problem with permissions. One potential issue is that I can't seem to see any confirmation that php postgresql support is enabled in the php info screen, despite the correct package installed and in the config line. Any ideas as to what's happening here? The nginx rules are pretty standard: server { # pg-pool admin listen 997; server_name localhost; root /opt/pgpooladmin; index index.php; location ~ .php$ { fastcgi_pass_header Set-Cookie; fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_index index.php; include fastcgi_params; } }

  Read the article

• MySQL problem with many concurrent connections

  - by user48303

  Hi, here's a sixcore with 32 GB RAM. I've installed MySQL 5.1.47 (backport). Config is nearly standard, except max_connections, which is set to 2000. On the other hand there is PHP5.3/FastCGI on nginx. There is a very simple php application which should be served. NGINX can handle thousands of request parallel on this machine. This application accesses MySQL via mysqli. When using non-persistent connections in mysqli there is a problem when reaching 100 concurrent connections. [error] 14074#0: *296 FastCGI sent in stderr: "PHP Warning: mysqli::mysqli(): [2002] Resource temporarily unavailable (trying to connect via unix:///tmp/mysqld.sock) in /var/www/libs/db.php on line 7 I've no idea to solve this. Connecting via tcp to mysql is terrible slow. The interesting thing is, when using persistent connections (add 'p:' to hostname in mysqli) the first 5000-10000 thousand requests fail with the same error as above until max connections (from webserver, set to 1500) is reached. After the first requests MySQL keeps it 1500 open connections and all is fine, so that I can make my 1500 concurrent requests. Huh? Is it possible, that this is a problem with PHP FastCGI?

  Read the article

• Postfix does not work after setting server hostname from plesk

  - by Michael

  I have recently set my server hostname from localhost.localdomain to xx.mydomain.com from the plesk control panel. However after doing this change postfix has stopped working, I tried restarting and regenerating the config files but to no avail. I am not familiar with postfix but I believe there is a setting to be changed in main.cf. Here are the relevant errors I receive: postfix/postfix-script: starting the Postfix mail system postfix/master: daemon started -- version 2.8.4, configuration /etc/postfix postfix/cleanup: fatal: host/service localhost/12768 not found: Name or service not known postfix/pickup: warning: maildrop/E5559996219: error writing 4FA2C996217: queue file write error postfix/master: warning: process /usr/libexec/postfix/cleanup pid 15334 exit status 1 postfix/master: warning: /usr/libexec/postfix/cleanup: bad command startup -- throttling Any ideas? EDIT Setting it back to localhost.localdomain makes it work again. The only references to localhost/12768 I can find in main.cf are: smtpd_milters = inet:localhost:12768 non_smtpd_milters = inet:localhost:12768 Should something be changed here? These two lines stay the same when I change the hostname. EDIT If I comment out the two mail filter lines (the ones shown above) and restart, postfix works with the new hostname. However this is obviously not the ideal solution...

  Read the article

• Postfix able to receive email but not able to send it

  - by c0mrade

  I had postfix running on my machine(comes with centos minimal), but today I configured it to use my domain for the sake of example this is my domain name example.com . Here is my config : alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 header_checks = regexp:/etc/postfix/header_checks html_directory = no inet_interfaces = all inet_protocols = ipv4 mail_owner = postfix mailbox_size_limit = 1073741824 mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man message_size_limit = 10485760 mydestination = $myhostname, localhost.$mydomain, localhost, $mydomain mydomain = example.com myhostname = mail.example.com mynetworks = 127.0.0.0/8 mynetworks_style = host myorigin = $mydomain newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES relayhost = smtp.$mydomain sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtpd_banner = $myhostname ESMTP $mail_name smtpd_client_restrictions = permit_mynetworks,reject_unknown_client,permit smtpd_recipient_restrictions = permit_mynetworks,permit_auth_destination,permit_sasl_authenticated,reject unknown_local_recipient_reject_code = 550 I need one email account to be able to send emails (password retrievals etc.). I read today somewhere that if you create unix account postfix will recognize it as email address so if your account username was ant your email would be [email protected]. So I tested that and tried to send email to [email protected] and I successfully received mail. When I try to send the email with ant task script, I'm not able to connect : Failed messages: javax.mail.MessagingException: Could not connect to SMTP host: mail.example.com, port: 25; nested exception is: java.net.ConnectException: Connection timed out: connect What am I missing here? Edit I'm able to telnet to localhost : Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 mail.example.com ESMTP Postfix

  Read the article

• --log-slave-updates is OFF but updates received from master are still logged to slave binary log?

  - by quanta

  MySQL version 5.5.14 According to the document, by the default, slave does not log to its binary log any updates that are received from a master server. Here are my config. on the slave: # egrep 'bin|slave' /etc/my.cnf relay-log=mysqld-relay-bin log-bin = /var/log/mysql/mysql-bin binlog-format=MIXED sync_binlog = 1 log-bin-trust-function-creators = 1 mysql> show global variables like 'log_slave%'; +-------------------+-------+ | Variable_name | Value | +-------------------+-------+ | log_slave_updates | OFF | +-------------------+-------+ 1 row in set (0.01 sec) mysql> select @@log_slave_updates; +---------------------+ | @@log_slave_updates | +---------------------+ | 0 | +---------------------+ 1 row in set (0.00 sec) but slave still logs the updates that are received from a master to its binary logs, let's see the file size: -rw-rw---- 1 mysql mysql 37M Apr 1 01:00 /var/log/mysql/mysql-bin.001256 -rw-rw---- 1 mysql mysql 25M Apr 2 01:00 /var/log/mysql/mysql-bin.001257 -rw-rw---- 1 mysql mysql 46M Apr 3 01:00 /var/log/mysql/mysql-bin.001258 -rw-rw---- 1 mysql mysql 115M Apr 4 01:00 /var/log/mysql/mysql-bin.001259 -rw-rw---- 1 mysql mysql 105M Apr 4 18:54 /var/log/mysql/mysql-bin.001260 and the sample query when reading these binary files with mysqlbinlog utility: #120404 19:08:57 server id 3 end_log_pos 110324763 Query thread_id=382435 exec_time=0 error_code=0 SET TIMESTAMP=1333541337/*!*/; INSERT INTO norep_SplitValues VALUES ( NAME_CONST('cur_string',_utf8'118212' COLLATE 'utf8_general_ci')) /*!*/; # at 110324763 Did I miss something?

  Read the article

• Database problem with MS JET

  - by Zimmy-DUB-Zongy-Zong-DUBBY

  I am migrating a bunch of sites which each use an Access database (or whatever an MDB file is). If I try to load the site, I get the following error: Microsoft OLE DB Provider for SQL Server error '80004005' [DBNETLIB][ConnectionOpen (Connect()).]SQL Server does not exist or access denied If I rename the MDB file, I get a complaint that the file does not exist, which makes sense. If the file is named correctly, the site tries to load for about 30 seconds or so, and then just fails with the above message. During this waiting period, I can see a lock file being created (and then at some point removed). The MDB file and it's parent dir have full permissions granted to all users. Given that the lock file is successfully created and removed, I don't think that this is a "real" permission issue. The OS is Windows Server 2003 SP2. I am not sure about much more detail on it's config wrt Access databases. I also don't know what version it is expected to be. VB code in question: set oConn=server.createobject("adodb.connection") DSNtemp="Provider=Microsoft.Jet.OLEDB.4.0;Data Source=D:\fullPathGoesHere\db\sitedb.mdb" oConn.Open DSNtemp

  Read the article

• How to get multipath working for Ubuntu Server 12.04

  - by mlampi

  I'm working on a project which aims to make use of Ubuntu servers running on enterprise class hardware. In our case that means IBM HS23E blade servers, QLogic 4GB fibre channel extension cards and quite old IBM DS4500 disk array with two controllers. At the moment we have fibre channel as only boot option and Ubuntu Server 12.04 installed just fine and is able to boot without multipath. I'm not a linux professional myself but in our team we have people who will understand the technical stuff. Don't let my post confuse :) The current situation is that we have only one fibre channel connection to a single disk array controller. Real life case would be of course quite different. At minimum we should have two fibre channel ports connected to two different switches and two different controllers. However, we have no idea how to set up multipath tool. Is the DM-MPIO the right software? At minimum we should be able to boot when multiple connections are available and achieve fault tolerance when any of them should be down. Since the disk array is not the latest hardware, I managed to find RDAC driver sources only for 2.6.x kernel. And we have 3.2.x. Another issue is to build a multipath.conf. The said driver sources are from IBM support and the QLogic drivers provided to Ubuntu installer are from Ubuntu site. It seems that RHEL and SLES would have near out of the box support but that is not an option for our project. Actual questions: - What is the recommended software tool for multipath for Ubuntu Server 12.04? - Is there available pre-made configurations or templates? Does it require disk array / controller specific settings or do a more generic config work? - Do you have expriences on similar setup and like to share the knowledge? I'll provide you with any additional information you might require. Thanks in advance.

  Read the article

• NX Client for Windows 7 Opens Remote Desktop in Multiple Windows

  - by Corey Kennedy

  What I'm trying to do: access my Ubuntu desktop remotely via NX Client on my Windows 7 laptop. My environment: server: Ubuntu 10.10 on AMD 1Ghz/512MB RAM PC client: Windows 7 on ThinkPad sl510 Software: server is running NXServer 3.4.0. Using xfce4 window manager. Laptop is using NXClient for Windows In my NX Client "Desktop" settings I've selected "Unix" and "Custom" for OS and environment. I've also specified "startxfce4" as the application to launch when NX connects. I am able to authenticate an NX session on my laptop. By this I mean, I can start the client on my laptop, enter credentials for my Linux user, and NX establishes a connection to the server and attempts to open a remote desktop window. The problem, though, is that this remote desktop is "fragmented" into many Windows. One window will display the bulk of my desktop (complete with desktop icons for "Home," "File System," and "Trash") while another window will contain the taskbar, and another window will contain the application strip. I can select each of these Windows individually, but I cannot click on any objects within them. I've searched Super User, Ubuntu Forums, NX help, Server Fault, and tried many Google searches - none have turned up another case of this particular problem. I'm stumped. Does anyone have any suggestions for what I might try? I'm guessing the problem has to do with my xfce config files, but I've only just setup this server - it's been a long time since I've used Linux and there's a lot I just don't know. What I am NOT trying to do: use Desktop sharing from Ubuntu, whereby I VNC into a desktop that I've already established on the server. I am trying to configure this Linux box as a headless server that I can stash someplace out-of-the-way in my house, then interact with through my laptop. I don't want to have a monitor or keyboard connected to the Linux box. Thanks for your help!

  Read the article

• PhpMyAdmin Missing parameter:

  - by Ali

  Everything was working fine until this moment I want to create a new database and I'm receiving this error db_create.php: Missing parameter: new_db (FAQ 2.8) Also when I was trying to export my database I also receive the following error export.php: Missing parameter: what (FAQ 2.8) export.php: Missing parameter: export_type (FAQ 2.8) When I looked it FAQ 2.8 from the suggested link in PHPMYADMIN 2.8 I get "Missing parameters" errors, what can I do? Here are a few points to check: In config.inc.php, try to leave the $cfg['PmaAbsoluteUri'] directive empty. See also FAQ 4.7. Maybe you have a broken PHP installation or you need to upgrade your Zend Optimizer. See http://bugs.php.net/bug.php?id=31134. If you are using Hardened PHP with the ini directive varfilter.max_request_variables set to the default (200) or another low value, you could get this error if your table has a high number of columns. Adjust this setting accordingly. (Thanks to Klaus Dorninger for the hint). In the php.ini directive arg_separator.input, a value of ";" will cause this error. Replace it with "&;". If you are using Hardened-PHP, you might want to increase request limits. The directory specified in the php.ini directive session.save_path does not exist or is read-only. I did tried with php.ini to make sure that I've session.save_path = "/tmp" I'm using Mac Xserver and running with MAMP I did tried everything to restart my server and nothing help. Please if anyone help me to give me some suggestion. Apologize if I post in a wrong place.

  Read the article

• ESXi - change to thin - virtual disk filesize is the same

  - by sven

  running ESXi 5.5 here with a datastore on a single SSD. Now, I thought about changing to thin disks from thick and found that I could use a tool on the ESXi host to do that. However, the file size of the new created virtual disk is not changing. I run: vmkfstools -i loader.vmdk -d 'thin' thinloader.vmdk Destination disk format: VMFS thin-provisioned Cloning disk 'loader.vmdk'... Clone: 100% done. After that I compared the virtual disksizes: ls -la *.vmdk -rw------- 1 root root 32212254720 Jun 10 08:25 loader-flat.vmdk -rw------- 1 root root 467 May 21 17:04 loader.vmdk -rw------- 1 root root 32212254720 Jun 10 08:27 thinloader-flat.vmdk -rw------- 1 root root 520 Jun 10 08:33 thinloader.vmdk Stats on the original file: stat loader.vmdk File: loader.vmdk Size: 467 Blocks: 0 IO Block: 131072 regular file Device: 8bf64d175e27544ch/10085333178302026828d Inode: 419443780 Links: 1 Access: (0600/-rw-------) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2014-01-25 10:17:34.000000000 Modify: 2014-05-21 17:04:06.000000000 Change: 2014-05-21 17:04:06.000000000 and on the thin file: stat thinloader.vmdk File: thinloader.vmdk Size: 520 Blocks: 0 IO Block: 131072 regular file Device: 8bf64d175e27544ch/10085333178302026828d Inode: 432026692 Links: 1 Access: (0600/-rw-------) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2014-06-10 08:27:45.000000000 Modify: 2014-06-10 08:33:30.000000000 Change: 2014-06-10 08:33:30.000000000 Anyone an idea why the disk is not providing any more space (tried with multiple VM's already - all the same)? Also, I have noticed that the newly created file "autoappend" "-flat" to the disk ... Thanks Sven Update - diff of the vmdk config* --- loader.vmdk +++ thinloader.vmdk @@ -7,15 +7,17 @@ createType="vmfs" -RW 62914560 VMFS "loader-flat.vmdk" +RW 62914560 VMFS "thinloader-flat.vmdk" ddb.adapterType = "lsilogic" +ddb.deletable = "true" ddb.geometry.cylinders = "3916" ddb.geometry.heads = "255" ddb.geometry.sectors = "63" ddb.longContentID = "6d95855805dfa0079327dfee29b48dca" -ddb.uuid = "60 00 C2 98 d5 7d 17 bf-ac 54 70 b1 2d 39 43 d5" +ddb.thinProvisioned = "1" +ddb.uuid = "60 00 C2 93 c4 13 6c cf-bb 7b 34 c9 2c b4 dc 1e" ddb.virtualHWVersion = "8"

  Read the article

• Migrating from tomcat to tc server - receiving java.sql.SQLException on startup

  - by user470184

  I'm receiving below error when I start tcServer. I do not receive this error on standalone version of tomcat. Is there extra config I need to add for tcServer ? WARNING: Unexpected exception resolving reference java.sql.SQLException: Io exception: The Network Adapter could not establish the connection at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:112) at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:146) at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:255) at oracle.jdbc.driver.T4CConnection.logon(T4CConnection.java:387) at oracle.jdbc.driver.PhysicalConnection.(PhysicalConnection.java:441) at oracle.jdbc.driver.T4CConnection.(T4CConnection.java:165) at oracle.jdbc.driver.T4CDriverExtension.getConnection(T4CDriverExtension.java:35) at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:801) at org.apache.tomcat.jdbc.pool.PooledConnection.connectUsingDriver(PooledConnection.java:277) at org.apache.tomcat.jdbc.pool.PooledConnection.connect(PooledConnection.java:182) at org.apache.tomcat.jdbc.pool.ConnectionPool.createConnection(ConnectionPool.java:699) at org.apache.tomcat.jdbc.pool.ConnectionPool.borrowConnection(ConnectionPool.java:631) at org.apache.tomcat.jdbc.pool.ConnectionPool.init(ConnectionPool.java:485) at org.apache.tomcat.jdbc.pool.ConnectionPool.(ConnectionPool.java:143) at org.apache.tomcat.jdbc.pool.DataSourceProxy.pCreatePool(DataSourceProxy.java:116) at org.apache.tomcat.jdbc.pool.DataSourceProxy.createPool(DataSourceProxy.java:103) at org.apache.tomcat.jdbc.pool.DataSourceFactory.createDataSource(DataSourceFactory.java:539) at org.apache.tomcat.jdbc.pool.DataSourceFactory.getObjectInstance(DataSourceFactory.java:237) at org.apache.naming.factory.ResourceFactory.getObjectInstance(ResourceFactory.java:140) at javax.naming.spi.NamingManager.getObjectInstance(NamingManager.java:304) at org.apache.naming.NamingContext.lookup(NamingContext.java:793) at org.apache.naming.NamingContext.lookup(NamingContext.java:140) at org.apache.naming.NamingContext.lookup(NamingContext.java:781) at org.apache.naming.NamingContext.lookup(NamingContext.java:153) at org.apache.catalina.core.NamingContextListener.addResource(NamingContextListener.java:1028) at org.apache.catalina.core.NamingContextListener.createNamingContext(NamingContextListener.java:637) at org.apache.catalina.core.NamingContextListener.lifecycleEvent(NamingContextListener.java:238) at org.apache.catalina.util.LifecycleSupport.fireLifecycleEvent(LifecycleSupport.java:142) at org.apache.catalina.core.StandardServer.start(StandardServer.java:747) at org.apache.catalina.startup.Catalina.start(Catalina.java:595) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:289) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:414)

  Read the article

• Setting my NIC to full duplex

  - by David

  I am trying to optimize the network speed of my Solaris X86 server, and have discovered that the Cisco 3548 that it is connected to has issues with the NIC in my server. The NIC appears to have not been configured fully, and is coming up 100 half-duplex. The 3548 ports are all set to 100 full. Ideally I'd like to have the server set for 100 full, and have been attempting to configure it using ndd commands. However I have had no results. The following command: -bash-3.00# dladm show-dev rtls0 link: unknown speed: 100 Mbps duplex: unknown The NIC shows up as: pci bus 0x0001 cardnum 0x06 function 0x00: vendor 0x10ec device 0x8139 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ which should be configurable. I have modified the configuration file from auto config (5) to 100 fdx (4) to no avail. If there is no other choice, I could alter the Cisco 3548 to be 100 half-duplex. However, this solution causes huge performance loss. Currently throughput is about 500Kbps, when it should be around 40Mbps.

  Read the article

• Exclamation 403 forbidden for cgi-bin/ and cannot protect site with password

  - by gasgdasdgasdg

  First problem i have is i am getting 403 forbidden error for cgi-bin/ I have created a new /var/www2/ i can access it fine. php runs fine. Second problem is I cannot password protect it. i first tried doing htpasswd, it asks for login but everytime i login it keeps asking for new one. its getting frustrating, i have tried all tricks. and doesn't seem to work. this is a virtual host config inside sites-available. httpd.conf is empty but i have apache2.conf Code: NameVirtualHost 12.12.12.12. <VirtualHost 12.12.12.12> ServerAdmin webmaster@localhost DocumentRoot /var/www2/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www2/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /var/www2/cgi-bin/ <Directory "/var/www2/cgi-bin/"> AllowOverride Options Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch AddHandler cgi-script cgi pl Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost>

  Read the article

• ASP.NET sending email through exchange problem

  - by Solmead

  I have an exchange 2010 server running on Windows 2008 R2, I also have a remote webserver running Windows 2003 with multiple sites on it (all asp.net mvc 2 sites). I setup a Transport in exchange and all the websites on my remote web server can send email no problem to anyone in the exchange server and to any external domain. Now for my problem. I am having issues with that webserver, so I moved one of the websites to run on my exchange server, it runs well (low hit website) except that email doesn't work from that site. I tried changing the Transport in exchange to add the IP address of the local machine and the 127.0.0.1 addresses and it still isn't sending any email. Any ideas on how to get this working? The remote websites can still send email no problem, the version of the site that I had to move on the remote server can still email, but on the exchange server for that website email does not send. I would guess it is a Transport issue, since it is running on the same server a firewall shouldn't be the issue. I changed the smtp setting in web.config to localhost, and now I do receive email to my account on the exchange server, but I do not receive any emails on outside addresses. To add more description, this is a custom developed asp.net mvc 2 website. And no errors were being generated in the code when sending the email in either case.

  Read the article

< Previous Page | 469 470 471 472 473 474 475 476 477 478 479 480  | Next Page >