Search Results

Search found 13752 results on 551 pages for 'ip protocol'.

Page 479/551 | < Previous Page | 475 476 477 478 479 480 481 482 483 484 485 486  | Next Page >

• Plesk wildcard subdomain not working

  - by avdgaag

  I'm trying to set up a wildcard subdomain on my VPS. Ultimately I want to end up with this: main site: my.domain.tld subdomain: sub1.my.domain.tld - should end up serving my.domain.tld/sub1 I am using plesk 8.6. I have created a DNS A record pointing at my VPS' IP. I have then restarted the DNS server and waited up to 24 hours. But trying ping sub1.my.domain.tld results in an unknown host error. So I know there's more stuff involved, configuring apache etc. But so far, I cannot even get the subdomain working at all, let alone serve up the right content. I have also tried a CNAME record, to no effect. I have also tried creating a regular subdomain with a fixed name, which also does not work. Pre-configured subdomains DO work, like ftp.my.domain.tld or mail.my.domain.tld. I am clearly missing something here, but my hosting provider charges a small fortune for any support request not involving hardware physically burning down, so I'm hesitant to ask them. Any ideas?

  Read the article

• Domain joined computer unable to access servers through VPN

  - by kscott

  Our servers are in a virtual off site hosting center, our office has a vpn connection to the data center, but for reasons I don't understand we also have to connect to the Citrix Access Gateway (CAG) client in order to access the servers. I am a programmer with rather limited ops knowledge including a weak grasp of networking and terminology. Bear with me. I was just given a new laptop, which is a 64 bit Windows 7 system unlike my previous 32 bit Windows XP desktop which was able to connect without issue. My laptop has been joined to the domain so that I login with my AD credentials, I am able to connect to the CAG and get authenticated, and after doing this I can ping our servers and they resolve to the correct internal IP addresses, but I am unable to use remote desktop to the servers, connect to SQL servers through my local SQL Management Studio, navigate to them through the file system, or view any of our internal intranet websites. All of which I was able to do previously. I have tried turning off my Windows firewall and the problem remains, the DNS servers are set to the correct IPs of our domain controllers, and the ops guys here are a little stumped. Does any one have any suggestions?

  Read the article

• Uninstall IIS on Windows 7

  - by CJM

  I've just rebuilt my development machine and installed IIS. I then installed the Web Deployment tool and used this to restore my previously-backed-up websites to the clean machine. Unfortunately the restoration didn't work correctly/fully. I couldn't easily correct the problem, so I decided to uninstall/reinstall IIS and recreate the sites manually. I uninstalled IIS and rebooted, but there was still plenty of stuff left around such as various files in /windows/system32/inetsrv/ which I tried to delete manually (with limited success!). I rebooted again and tried to reinstall IIS - it reported an error (no meaningful message) and requested another reboot. The event log includes the following errors: The World Wide Web Publishing Service (WWW Service) did not register the URL prefix http://*:80/gallery for site 1. The site has been disabled. and Unable to bind to the underlying transport for [::]:80. The IP Listen-Only list may contain a reference to an interface which may not exist on this machine. I'd like to avoid another rebuild. Can I completely remove IIS, such that I can reinstall it from scratch? Or can I 'fix' the current setup so that IIS will reinstall over what is already there?

  Read the article

• How to set up a serial connection to a Windows 7 computer

  - by oli_arborum

  I need to set up a "dial in" connection to a Windows 7 (Ultimate) computer via a serial null-modem cable to be able to connect from a Windows XP client to that computer and exchange data over IP. Question 1: How do I do that? I did neither find the information via Google nor in the MSDN. Seems like no one tried ever before... ;-) I already managed to install a legacy modem device called "Communications cable between two computers" and found the menu entry "New Incoming Connection..." in Network and Internet Network Connections. When I finish this wizard I get the message that the "Routing and Remote Access service" cannot be started. In the event viewer I see the following error messages: "The currently configured authentication provider failed to load and initialize successfully. The requested name is valid, but no data of the requested type was found." (Source: RemoteAccess, EventID: 20152) "The Routing and Remote Access service terminated with service-specific error The requested name is valid, but no data of the requested type was found." (Source: Service Control Manager, EventID: 7024) The Windows 7 installation is "naked", i.e. no additional software or services are installed. Question 2: Am I on the right path to set up the connection? Question 3: How can I get the Routing and Remote Access service running?

  Read the article

• Why are FMS logs filled with 'play' event status code 408 for a failed webcast?

  - by Stu Thompson

  Recently we had a live webcast event go horribly wrong. I'm doing the technical post-mortem, with limited information. We know that the hardware encoder (a Digital Rapid Touch Stream Web HDI) was unable to send upstream at a sustained reliable high rate. What we don't know is if the encoder's connection was problematic (Zürich), or that of the streaming server (in Frankfurt). Unfortunately, I've got three different vendors all blaming each other (the CDN who runs the server, the on-site ISP and the on-site encoding team.) In the FMS log files I see a couple of interesting things: Zillions of Status Code 408 on play event entries for clients. Adobe's documentation stats that this "Stream stopped because client disconnected". ("Zillions" would be a ratio of 10 events for every individual IP address.) Several unpublish / (re)publish events per hour for the encoder I'd like to know if all those 408s could tell me with authority that the FMS server was starved for bandwidth, or that the encoding signal was starved (and hence the server was disconnecting clients.) Any clues?

  Read the article

• IIS7 binding to subdomain causing authentication errors (TFS 2010)

  - by Tommy Jakobsen

  I'm trying to bind a IIS web site (Team Foundation Services 2010) to a subdomain, which is causing authentication errors. First I'll explain what I've done to set it up. This is the fist time I do this, so please correct me if I'm wrong. The web server is a stand-alone Windows Server 2008 R2 x64, running IIS7 with .NET Framework 4. I have the following A-records, pointing to my server: server.mydomain.com *.server.mydomain.com So all subdomains of server.mydomain.com points to the server. In IIS7 I have a web site (TFS 2010) on port 8080, with a virtual directory (named tfs) that is using Windows Authentication. I have one binding on the web site pointing to all unassigned IP addresses, port 8080 and having a host name of tfs.server.mydomain.com. Now, shouldn't I be able to access the virtual directory through: http://tfs.server.mydomain.com/tfs That is not working. However, I can access it through: http://tfs.server.mydomain.com:8080/tfs But, it won't let me authenticate using a Windows account (Server\Username). A windows account that I can authenticate with, when accessing the site through http://localhost:8080/tfs. What am I missing here?

  Read the article

• Gmail.com detect mail as spam, but the server is not on any BlackList

  - by Tomer W

  I have an issue with Google. (GMail to be exact) About 1 month ago, we had a security breach, and mail was relayed through our servers. we got listed in almost ALL Black-Lists :( we fixed the problem, and requested removal from Black-lists, which was granted easily. currently (over 3 weeks), we are not sending any spam anymore. furthermore, we got clear from all the Black-lists (MxToolBox Black-List Search Result) But, GMail still refuse to get Anything from the server, stating '550 Spam'. Following, Telnet attempt to send to gmail: 220 mx.google.com ESMTP g47si45436208eep.123 helo megatec.co.il 250 mx.google.com at your service mail from: <[email protected]> 250 2.1.0 OK g47si45436208eep.123 rcpt to: <[email protected]> 250 2.1.5 OK g47si45436208eep.123 Data 354 Go ahead g47si45436208eep.123 Test123 . 550-5.7.1 [62.219.123.33 11] Our system has detected that this message is 550-5.7.1 likely unsolicited mail. To reduce the amount of spam sent to Gmail, 550-5.7.1 this message has been blocked. Please visit 550-5.7.1 http://support.google.com/mail/bin/answer.py?hl=en&answer=188131 for 550 5.7.1 more information. g47si45436208eep.123 Connection to host lost. i tried filling the form @ Gmail - Report Delivery Problem i also tried reaching Google by phone, but the message was to go to the Link mentioned above. I Checked ReverseDNS and is ok... We dont have TLS, but that shouldn't be a problem, shouldn't it? Note: we are not a Bulk sender. Anyone has an idea? what can be blocking our IP? Anyone know whom can be contacted in order to resolve this BL listing?

  Read the article

• Which ports are needed for NTLM (Windows Authentication) to connect to SQL Server?

  - by Adam Bellaire

  I've got SQL server running on a machine which is not in a domain, and which is not operating in mixed mode (it's running with "Windows Authentication"). I'm trying to connect to it from a Linux web server running freetds via TCP/IP, using NTLM to authenticate. The firewall on the SQL server is very restrictive. 1433 is open to my web server, but I'm getting conflicting information from the web on what additional ports (TCP/UDP) are needed for NTLM to succeed. It is currently fail; I can talk on 1433 to request NTLM, but the actual authentication always fails. One source says 137, 138, 139, but those are just the NetBIOS ports. Do I really need those? Another source says 135. Still others seem to say 1434... I can't make heads or tails of it. Dammit Jim, I'm a programmer, not a network administrator! EDIT: The exact error message: Msg 18452, Level 14, State 1, Server , Line 0 Login failed for user '(null)'. Reason: Not associated with a trusted SQL Server connection. Msg 20002, Level 9, State -1, Server OpenClient, Line -1 Adaptive Server connection failed I am attempting to connect with a remote machine username, i.e. 'servername\username'. Some sources recommend that I set up mirrored accounts on the local and remote machines, but the local machine is running Linux, not IIS under Windows.

  Read the article

• Rsyslogd not listening on port

  - by amorfis

  I installed rsyslogd on ubuntu server, started it and everything looks fine, but the port the server should listen on is not opened. ubuntu@node7:~$ sudo service rsyslog restart rsyslog stop/waiting rsyslog start/running, process 14114 Netstat shows it is not listening: ubuntu@node7:~$ netstat -tlan Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 320 172.22.0.17:22 10.8.8.38:61335 ESTABLISHED tcp6 0 0 :::22 :::* LISTEN tcp6 0 0 :::2776 :::* LISTEN tcp6 0 0 :::2777 :::* LISTEN tcp6 0 0 172.22.0.17:2777 172.22.0.11:56554 ESTABLISHED tcp6 0 0 172.22.0.17:2776 172.22.0.11:39780 ESTABLISHED This is how /etc/rsyslog.conf looks like (most comments omitted): ubuntu@node7:~$ cat /etc/rsyslog.conf ################# #### MODULES #### ################# $ModLoad imuxsock # provides support for local system logging $ModLoad imklog # provides kernel logging support (previously done by rklogd) $ModLoad imtcp $InputTCPServerRun 514 ########################### #### GLOBAL DIRECTIVES #### ########################### $ActionFileDefaultTemplate RSYSLOG_TraditionalFileFormat $RepeatedMsgReduction on $WorkDirectory /var/spool/rsyslog $FileOwner syslog $FileGroup adm $FileCreateMode 0640 $DirCreateMode 0755 $Umask 0022 $PrivDropToUser syslog $PrivDropToGroup adm $IncludeConfig /etc/rsyslog.d/*.conf In /etc/rsyslog.d/35-server-per-host.conf I have following lines, and I suspect this can be the cause. What does it mean? # Stop processing of all non-local messages. You can process remote messages # on levels less than 35. :fromhost-ip,!isequal,"127.0.0.1" ~ and if it is, how could I change it to have server listening and receiving and logging messages? UPDATE: I commented out suspected line, but still it's not listening on port 514

  Read the article

• Unable to ping domain.local, but can ping server.domain.local

  - by Force Flow

  I have a single windows 2008 server running active directory, group policy, and DNS. DHCP is running from the firewall (this is because there are multiple branch locations, and each location has its own firewall supplying DHCP. But, for this problem, the server and workstation are at the same location). On an XP workstation, if I try to visit \\domain.local or ping domain.local, the workstation can't find it. A ping returns Ping request could not find host domain.local. If I try to visit \\server or \\server.domain.local or ping server or server.domain.local, I'm able to connect normally. If I ping or visit domain.local on the server, I'm able to connect normally. A-Records are in place in the DNS service for server, domain.local, and server.domain.local. A reverse lookup zone also is enabled and PTR records are in place. If I wait 20-30 minutes, I am eventually able to ping and visit domain.local--but, when attempting to ping, it takes 30 second to return an IP address. I am also unable to join a new workstation to the domain during this wait period. If I try, the error message returned is "network path not found". Is there something I'm missing?

  Read the article

• Virtual Wifi Issue Windows 7

  - by Matt

  Lately I've been trying to use my laptop as a wireless router in my room. I have it connected to my school's network through ethernet, and I want to set up wireless so that I can use Wifi on my Android phone and iPod Touch. In the past, I used Connectify, but I started having an issue where my phone would find the network, connect, attempt to get the IP, and then suddenly the network would disappear. Then it'd pop up again, and the same process would happen over and over. I decided that I'd totally uninstall Connectify, but after that, neither Virtual Router Manager nor the command prompt could create a viable network either. My phone and even my iPod now encounter the same problem. Neither can successfully connect. So evidently there is something wrong with the laptop's virtual wifi feature, and I have no idea what that could be. I've tried enabling certain services that virtual wifi supposedly relies on, but some of them don't start, namely Remote Access Connection Manager. But I also have read that these enable on their own and that if they are normally not enabled it's fine. Furthermore, I even uninstalled and reinstalled the drivers for my wireless card. Any ideas as to why my virtual wifi won't function? Anything? I really would love to get this working...

  Read the article

• Setting up Red Hat Enterprise Linux Server as a mail exchange server

  - by Syedur

  I am a Unix/Linux/Windows Server noob. So, keep that in mind before you throw your stones at my glass house. :P I have a Windows Server 2008 R2 machine that's acting as domain controller, Server A. It's also running a DNS server. I have a Red Hat Enterprise Linux Server 5.3, Server B that is intended for mail server. In order for the mail delivery to happen, I understand that I have to set an MX record on Server A and point it to Server B. Well, I did. I manually added a host name on Server A and pointed to Server B's IP address. Then I added an MX record and pointed it to the host name. That didn't do the trick. After taking the above steps, I used the "dig" command on Server B to lookup the MX record coming back from Server A and it wasn't what I was expecting. What am I doing wrong here? I have noticed that... my Windows machines that are joined to the domain (Server A) are listed under the host names. The machines that are not joined to the domain are not list. This is fine, I am not worried about this. What does concern me, do I have to join the Server B to domain in order for Server A to recognize as a valid host and forward the MX properly? If so, some simple steps on how to join Server B to the domain would also help.

  Read the article

• Problems with X11GraphicsDevice on Suse 11

  - by Daniel

  Hi, On servers running Suse 11 I'm experiencing hangups in sun.awt.X11GraphicsDevice.getDoubleBufferVisuals(Native Method) when connecting via Citrix (and setting DISPLAY to localhost:11.0). Running exactly the same code in exactly the same environment, excepth through Exceed (with DISPLAY set to my workstation's IP) it runs like clockwork. The error is not intermittent, it happens every time Reinstalling the OS does not help Can not reproduce it on Suse 10 This is what the main thread stack looks like: [junit] "main" prio=10 tid=0x0000000040112000 nid=0x6acc runnable [0x00002b9f909ae000] [junit] java.lang.Thread.State: RUNNABLE [junit] at sun.awt.X11GraphicsDevice.getDoubleBufferVisuals(Native Method) [junit] at sun.awt.X11GraphicsDevice.makeDefaultConfiguration(X11GraphicsDevice.java:208) [junit] at sun.awt.X11GraphicsDevice.getDefaultConfiguration(X11GraphicsDevice.java:182) [junit] - locked <0x00002b9fed6b8e70 (a java.lang.Object) [junit] at sun.awt.X11.XToolkit.(XToolkit.java:92) [junit] at java.lang.Class.forName0(Native Method) [junit] at java.lang.Class.forName(Class.java:169) [junit] at java.awt.Toolkit$2.run(Toolkit.java:834) [junit] at java.security.AccessController.doPrivileged(Native Method) [junit] at java.awt.Toolkit.getDefaultToolkit(Toolkit.java:826) [junit] - locked <0x00002b9f94b8ada0 (a java.lang.Class for java.awt.Toolkit) [junit] at java.awt.Toolkit.getEventQueue(Toolkit.java:1676) [junit] at java.awt.EventQueue.invokeLater(EventQueue.java:954) [junit] at javax.swing.SwingUtilities.invokeLater(SwingUtilities.java:1264) ... Has anyone experienced something similar? Could this be a problem in Suse 11's display handling? I'm thankful for any input at this point - I'm fresh out of ideas :)

  Read the article

• ASA Slow IPSec Performance with Inconsistent Window Size

  - by Brent

  I have a IPSec link between two sites over ASA 5520s running 8.4(3) and I am getting extremely poor performance when traffic passes over the IPSec VPN. CPU on the devices is ~13%, Memory at 408 MB, and active VPN sessions 2. The load on both of the the devices is particularly low. Latency between the two sites is ~40ms. Screenshot of wireshark file transfer between the two hosts over the firewall IPSec VPN performing at 10MBPS. Note the changing window size. http://imgur.com/wGTB8Cr Screenshot of wireshark file transfer between the two hosts over the firewall not going over IPSec performing at 55MBPS. Constant window size. http://imgur.com/EU23W1e I'm showing an inconsistent window size when transferring over the IPSec VPN ranging in 46,796 to 65535. When performing at 55+MBPS, the window size is consistently 65,535. Does this show a problem in my configuration of the IPSec VPN in the ASA or a Layer1/2 issue? Using ping xxxxxx -f -l I finally get a non-fragment at 1418 bytes so 1418+28 for IP/ICMP headers = 1446. I know that I have 1500 set on the ASA and Ethernet. I do have "Force Maximum segment size for TCP proxy connection to be" "1380" bytes set under Configuration Advanced TCP Options on the ASA. Using IPERF, I am getting a "TCP Window Full" every few seconds and ~3 MBPS performance. http://imgur.com/elRlMpY Show Run on the ASA http://pastebin.com/uKM4Jh76 Show cry accelerator stats http://pastebin.com/xQahnqK3

  Read the article

• Using "route add" to tell my computer to use a direct ethernet connexion instead of wifi ?

  - by TheSamFrom1984

  2 PCs are involved. Both are connected to the internet via Wifi on the same router. I can ping to/from each other and share folders flawlessly, but I'd like to be able to set a direct Ethernet link between them to speed up file transfers AND keep the Wifi connections (no gateway). So I plugged my RJ45 cable, and set up the connection. It works, but the PCs are only using this connection if one of them if disconnected from the Wifi. PC1 local address is 192.168.0.7 on its ethernet interface, and 192.168.1.21 on the wifi one. PC2 local address is 192.168.0.6 on its ethernet interface, and 192.168.1.22 on the wifi one. My question is : I'd like to using the route add command to tell PC1 to use the Ethernet interface when it needs to connect with PC2, by specifying "IF 2" at the end of the route add command. How can I do this ? I don't know what to put in the "gateway" parameter of the command, and everything I tried returns "the parameter is incorrect" (i don't know which one). ipconfig /all on PC1 : Windows IP Configuration Host Name . . . . . . . . . . . . : Sam-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : NETGEAR WG111v3 54Mbps Wireless USB 2.0 Adapter Physical Address. . . . . . . . . : 00-22-3F-DA-51-56 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::1d33:60b:476c:d396%12(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.1.21(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : vendredi 27 novembre 2009 15:38:48 Lease Expires . . . . . . . . . . : dimanche 29 novembre 2009 07:33:04 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DHCPv6 IAID . . . . . . . . . . . : 301998655 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-12-7E-58-EA-00-1A-4D-59-B2-71 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1A-4D-59-B2-71 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::f598:c3a0:df8d:706e%11(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 234887757 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-12-7E-58-EA-00-1A-4D-59-B2-71 DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled

  Read the article

• Amazon VPC NAT not working

  - by rpkelly

  I'm trying to create a NAT instance for my VPC to allow instances on private subnets connect to the internet (most importantly, S3). I tried following the instructions here: http://docs.amazonwebservices.com/AmazonVPC/2011-07-15/UserGuide/index.html?VPC_NAT_Instance.html . Unfortunately, the instances in the private subnet (call it 10.10.2.0/24) cannot reach the internet. I have done the following: Create a NAT instance (Amazon's ami-vpc-nat-1.0.0-beta.i386-ebs (ami-d8699bb1)) in public subnet (call it 10.10.1.0/24). Changed "Source / Dest Check" to disabled. Created a new entry in the default routing table (which is used by 10.10.2.0/24) and had it point to the ID of the newly created instance. Associated an Elastic IP address with the NAT instance. Allowed all outbound traffic on the security group of the NAT instance. Ensured that all traffic could pass between the two subnets. I've tried also doing this with an existing instance using iptables, but had no luck. And I have verified that sys.net.ipv4.ip_forward is 1, just in case anyone was wondering. And I still have no internet connectivity from the instances on 10.10.2.0/24. Does anyone have any suggestions?

  Read the article

• DNS, subdomain, and IPv6 -- possible to add subdomain.example.com NS record to an IPv6 host?

  - by mpbloch

  example.com is listed with a registrar -- specifically, answerable.com. I want to host a subdomain in-house, specifically home.example.com. I am using an ipv6 gateway, specifically gogo6, to have a public IPv6 address. The IP address looks like 2001:xxxx:xx47. Then http://[2001:xxxx:xx47] goes to my test site (an instance of IIS7). I can add a quad-A record for my primary site -- home.example.com AAAA 2001:xxxx:xx47. Then http//home.example.com loads correctly. Must I add an A or quad-A record for all sub.home.example.com to my answerable.com DNS manager for example.com? Or can I delegate DNS queries to *.home.example.com to the machine at [2001:xxxx:xx47]? I have tried to add a AAAA record for tunnel.example.com to [2001:xxxx:xx47], and then add an NS entry for home.example.com to tunnel.example.com, but browsing then results in "DNS lookup error" from my browser. Is this a configurable scenario? Can DNS for subdomain only be delegated to IPv4 addresses?

  Read the article

• Subdomains and address bar

  - by Priednis

  I have a fairly noob question about how subdomains work. As I understand at first the DNS server specifies that a request for certain subdomain.domain.com has to go to the IP address of domain.com, and the webserver at domain.com further processes the request and displays the needed subdomain page. It is not entirely clear to me how (for example Apache) server does it. As I understand there can be entries in vhosts.conf file which specify folders that contain the subdomain data. Something like: <VirtualHost *> ServerName www.domain.com DocumentRoot /home/httpd/htdocs/ </VirtualHost> <VirtualHost *> ServerName subdomain.domain.com DocumentRoot /home/httpd/htdocs/subdomain/ </VirtualHost> and there also can be redirect entries in .htaccess files like rewritecond %{http_host} ^subdomain.domain.com [nc] rewriterule ^(.*)$ http://www.domain.com/subdomain/ [r=301,nc] however in this case the user gets directed to the directory which contains the subdomain data but the user gets "out" of the subdomain. I would like to know - how, when going to subdomain.domain.com the subdomain.domain.com, beginning of address remains visible in the address bar of the explorer? Can it be done by an alternate entry in .htaccess file? If a VirtualHost entry is specified in the vhosts.conf file, does it mean, that a new user account has to be specified for access to this directory?

  Read the article

• debian VM refusing all traffic apart from http

  - by james lewis

  I've got a VM with a fresh install of Debian (wheezy) and I've installed node and mongo on it. The VM is using a bridged network connection so I was expecting to be able to point my host machines browser at the ip address of the Debian VM (port 1337 for my node example or port 28017 for my mongo status page) and see one of the two services (node or mongo). My requests are refused though. As far as I can tell Debian allows all traffic by default and you have to manually configure iptables to drop traffic. I've checked iptables and it says it's setup to allow anything through. It looks like this: root@devbox:/home/jlewis# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination As a test I setup nginx and I was able to get to the nginx landing page from my host no problems so obviously http traffic is allowed. I then set nginx up to forward all traffic upstream to mongo - no problems there, I was able to see the status page. I then did the same for my example node server and again, no problems. So http traffic is fine, but all other traffic is blocked. Anyone know why debian might be refusing all other traffic other than iptables being setup to drop it? EDIT - output from netstat -nltp: Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:28017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:51028 0.0.0.0:* LISTEN 1541/rpc.statd tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 2462/sshd tcp 0 0 127.0.0.1:1337 0.0.0.0:* LISTEN 2794/node tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 2274/exim4 tcp 0 0 127.0.0.1:27017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 1510/rpcbind tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 2189/nginx tcp6 0 0 :::22 :::* LISTEN 2462/sshd tcp6 0 0 :::45335 :::* LISTEN 1541/rpc.statd tcp6 0 0 ::1:25 :::* LISTEN 2274/exim4 tcp6 0 0 :::111 :::* LISTEN 1510/rpcbind

  Read the article

• Postfix Whitelist before recipient restrictions

  - by GruffTech

  Alright. Some background. We have an anti-spam cluster trucking about 2-3 million emails per day, blocking somewhere in the range of 99% of spam email from our end users. The underlying SMTP server is Postfix 2.2.10. The "Frontline defense" before mail gets carted off to SpamAssassin/ClamAV/ ect ect, is attached below. ...basic config.... smtpd_recipient_restrictions = reject_unauth_destination, reject_rbl_client b.barracudacentral.org, reject_rbl_client cbl.abuseat.org, reject_rbl_client bl.mailspike.net, check_policy_service unix:postgrey/socket ...more basic config.... As you can see, standard RBL services from various companies, as well as a Postgrey service. The problem is, I have one client (out of thousands) who is very upset that we blocked an important email of theirs. It was sent through a russian freemailer who was currently blocked in two of our three RBL servers. I explained the situation to them, however they are insisting we do not block any of their emails. So i need a method of whitelisting ANY email that comes to domain.com, however i need it to take place before any of the recipient restrictions, they want no RBL or postgrey blocking at all. I've done a bit of research myself, http://www.howtoforge.com/how-to-whitelist-hosts-ip-addresses-in-postfix seemed to be a good guide at first, almost fixing my problem, But i want it to accept based on TO address, not originating server.

  Read the article

• setting up subdomain wildcard: configured A record, VirtualHost... still does not work

  - by user80314

  Running Apache on CentOS, trying to setup wildcard subdomains, basically I want .mydomain.com to point to mydomain.com With cPanel I added *.mydomain.com With WHM I made sure that A record is pointing to the right IP. I set my A record: * 14400 IN X.x.x.x My httpd.conf: ServerName _wildcard_.mydomain.com ServerAlias *.mydomain.com DocumentRoot /home/mydomain/public_html ServerAdmin [email protected] UseCanonicalName Off ## User userdomain# Needed for Cpanel::ApacheConf UserDir enabled userdomain <IfModule mod_suphp.c> suPHP_UserGroup userdomain userdomain </IfModule> <IfModule !mod_disable_suexec.c> <IfModule !mod_ruid2.c> SuexecUserGroup usergrdomain userdomain </IfModule> </IfModule> <IfModule mod_ruid2.c> RUidGid userdomain userdomain </IfModule> ScriptAlias /cgi-bin/ /home/mydomain/public_html/cgi-bin/ # To customize this VirtualHost use an include file at the following location # Include "/usr/local/apache/conf/userdata/std/2/mydomain/wildcard_safe.mydomain.com/*.conf" I have my VirtualHost in httpd.conf set to point to domain root. Restarted Apache, server, dns, still nothing. I have spent hours researching this, followed instructions, set everything correctly. What am I missing?

  Read the article

• DNS NAmeserver Aname and cname records

  - by David

  Hi - I am inexperienced in the configuration of DNS and have an issue with dominan hosting set up. I have two domains 'www.mydomain1.com' and 'www.mydomain2.com', with mydomain2 pointed at the same place as mydomain1. The domains were passed to me recently by the person who previoulsy controlled them. I have an account with fasthosts in the uk. When I accepted the domains I could not access the DNS settings and enquired with fasthosts as to why. The replied saying 'The delegate hosting option for both domains were enabled and this is the reason why you were unable to find the option to edit the advanced DNS records. I have now disabled the delegate hosting option so you can now edit the advanced DNS records for both domains in your account.' When i log into the fasthost control panel now i can access the DNS controls but both domains have no A Record of Cname record set up. I am concerned that fasthosts have blatted the previous Nameserver entries and set me up on theirs but not added any record. 'www.mydomain1.com' currently still works but 'www.mydomain2.com' does not find the site anymore. i am worried i will lose mydomain1 to as teh dns changes filter through the system. my webhosting is at 'xxx.xxx.xxx.xxx/mydomain1.com/' and this is where I want both domains to point. Any advice would be much appreciated. one thing which is confusing me is that because I am on a shared server I have to put 'xxx.xxx.xxx.xxx/mydomain1.com/' to get to my site rather than just 'xxx.xxx.xxx.xxx'. The form on fasthosts for the aname record only allows an IP to be entered - does it add the mydomain1.com/ onto the end itself? Thanks for any help given - I'm quite worried about this David

  Read the article

• Why am I seeing MailSlot Browse messages on unrouted ports of my Linux box?

  - by nmichaels

  I have a Linux box (Debian squeeze) with several NICs. The ones of interest are: eth3 - my main link to the network (dhcp on 10.20.30.0/24) eth0 - the first connection to my test network (static: 192.168.1.2) eth4 - the second connection to my test network (static: 192.168.1.1) My routing table looks like this: $ sudo route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.20.30.0 * 255.255.255.0 U 0 0 0 eth3 default 10.20.30.254 0.0.0.0 UG 0 0 0 eth3 I have the 2 test net ports connected to each other with a crossover cable and an instance of wireshark running on each port. Every once in a while, I'll see a packet like the following show up. Who could be doing this, and how do I convince them to stop? I do have Samba running on the machine (for a cifs mount) but don't see why it would be sending packets out to unrouted ports. I had a Windows VM running in VMWare Client and thought that might be causing it, but it still happens without it. What I want is totally silent interfaces so I can run some tests with Scapy over them.

  Read the article

• Tell postfix to merge three Authentication-Results:-Lines into one?

  - by Peter

  I am running a postfix mta with debian wheezy. I am using postfix-policyd-spf-python, openkdim and opendmarc. When receiving e-mails from google (google apps with own domain) for example, the header looks like this: [...] Authentication-Results: mail.xx.de; dkim=pass reason="1024-bit key; insecure key" header.d=yyy.com [email protected] header.b=OswLe0N+; dkim-adsp=pass; dkim-atps=neutral<br> [...] Authentication-Results: mail.xx.de; spf=pass (sender SPF authorized) smtp.mailfrom=yyy.com (client-ip=2a00:1450:400c:c00::242; helo=mail-wg0-x242.google.com; [email protected]; [email protected]) [...] Authentication-Results: mail.xx.de; dmarc=pass header.from=yyy.com<br> [...] This means any of these programs creates it's own Authentication-Results:-Line. Is it possible to tell postfix to merge this into one single Authentication-Results:-Line? When I send an e-mail to google, it says: [...] Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates xxx.xxx.xxx.xxx as permitted sender) [email protected]; dkim=pass [email protected]; dmarc=pass (p=NONE dis=NONE) header.from=xxx.com [...] And this is exactly what I want. Just one Authentication-Results-Header. How can I do this? Thanks. Regards, Peter

  Read the article

• copy large LVM volume(14TB) from one server to another

  - by bruce

  recently,I have to copy a very large LVM volume()rom server A to server B. Below is the filesystem of server A and server B - server A [root@AVDVD-Filer ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_avdvdfiler-lv_root 16T 14T 1.5T 91% / tmpfs 3.0G 0 3.0G 0% /dev/shm /dev/cciss/c0d0p1 194M 23M 162M 13% /boot /dev/mapper/vg_avdvdfiler-test 2.3T 201M 2.1T 1% /test /dev/sr0 3.3G 3.3G 0 100% /mnt server B [root@localhost ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup-LogVol00 20G 2.5G 16G 14% / tmpfs 3.0G 0 3.0G 0% /dev/shm /dev/cciss/c0d0p1 194M 23M 162M 13% /boot /dev/mapper/VolGroup00-LogVol00 16T 133M 15T 1% /xiangao/lv1 /dev/mapper/VolGroup00-LogVol01 4.7T 190M 4.5T 1% /xiangao/lv2 I want to copy LVM volume /dev/mapper/vg_avdvdfiler-lv_root on server A to LVM volume /dev/mapper/VolGroup00-LogVol00 on server B . The server A and server B is in the same IP segment. IN the LVM volume on server A , there is all average 500M avi wmv mp4 etc. I tried mount /dev/mapper/vg_avdvdfiler-lv_root on server A to server B through NFS , then use cp command copy. It is clear I faild . Because the LVM volume is too big , I do not have good idea . I hope a good solution here. I'm a chinese, my english is very pool. sorry thanks everyone!

  Read the article

< Previous Page | 475 476 477 478 479 480 481 482 483 484 485 486  | Next Page >