Search Results

Search found 15439 results on 618 pages for 'wls configuration'.

Page 490/618 | < Previous Page | 486 487 488 489 490 491 492 493 494 495 496 497  | Next Page >

• Uploading file > 1 MB on Django admin gives 400 Bad Request response.

  - by ayaz

  I have a small Django (1.2.x) project deployed on Apache (2.x) via mod_wsgi (2.x). In the admin, if I upload a file < 1MB, I can get it through; however, for a file, say, 1.2MB in size, I get a 400 response from the server with "Error 400" in the body only. I am wondering why this is happening. As far as I can see, there is no LimitRequestBody set in Apache configuration. I have tried uploading with several browsers including: Firefox, Chrome, and Safari. In the log file for Apache, there is apparently no entry for requests that gave the 400 error response. This is strange. I should point out that the scenario where this is happening is thus: The project in question is deployed on two identical Apache servers (completely identical setup) that are behind a load balancer. On my development setup, of course, the problem does not surface. Any help with this will be very much appreciated.

  Read the article

• MD RAID 1 with external bitmap doesn't fully resync

  - by user64744

  I have an interesting configuration: dual boot system with a RAID 1 that needs to be visible in both Windows and Linux. The Windows install is Win 7 Enterprise, and the Linux install is Kubuntu 10.04. To get the RAID to work, I set it up using Windows's "Dynamic Disks" RAID 1, and brought it up in Linux using MD with no persistent superblock, and a write-intent bitmap on another partition. (Without this bitmap, MD had no way of knowing that the array was in sync, and would do a complete resync every time the array started.) The array is assembled like so: mdadm --build /dev/md1 -l 1 -n 2 -b /var/local/md1.bitmap /dev/sdb2 /dev/sdc2 I expected that the first time I ran this command, it would resync the array, write out a bitmap with no dirty chunks, and all would be good. This wasn't the case: after completing the resync, the bitmap was mostly clean, but about 5% dirty blocks remained, as revealed by mdadm -X /var/local/md1.bitmap I didn't mount the filesystem on /dev/md1 or touch it in any other way. I then found that stopping and restarting the array: mdadm --stop /dev/md1 mdadm --build /dev/md1 -l 1 -n 2 -b /var/local/md1.bitmap /dev/sdb2 /dev/sdc2 did indeed read in the bitmap, with an ensuing resync that went quickly because most of the blocks were marked clean. The confusing part is that this resync further reduced the number of dirty blocks, but still did not remove all of them. By repeatedly stopping and restarting I could slowly bring the dirty block count down to around 0.6%, where it seemed to level out. Any ideas what could be causing this? It smells to me of a race condition somewhere that leads to blocks either being skipped over during synchronization or not properly cleared from the bitmap, but I really have no evidence to prove this. It doesn't look like hardware issues since both drives are new and have zero read errors and reallocated sectors reported by smartctl -a.

  Read the article

• SSH works in putty but not terminal

  - by Ryan Naddy

  When I try to ssh this in a terminal: ssh [email protected] I get the following error: Connection closed by 69.163.227.82 When I use putty, I am able to connect to the server. Why is this happening, and how can I get this to work in a terminal? ssh -v [email protected] OpenSSH_6.0p1 (CentrifyDC build 5.1.0-472) (CentrifyDC build 5.1.0-472), OpenSSL 0.9.8w 23 Apr 2012 debug1: Reading configuration data /etc/centrifydc/ssh/ssh_config debug1: /etc/centrifydc/ssh/ssh_config line 52: Applying options for * debug1: Connecting to sub.domain.com [69.163.227.82] port 22. debug1: Connection established. debug1: identity file /home/ryannaddy/.ssh/id_rsa type -1 debug1: identity file /home/ryannaddy/.ssh/id_rsa-cert type -1 debug1: identity file /home/ryannaddy/.ssh/id_dsa type -1 debug1: identity file /home/ryannaddy/.ssh/id_dsa-cert type -1 debug1: identity file /home/ryannaddy/.ssh/id_ecdsa type -1 debug1: identity file /home/ryannaddy/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5 debug1: match: OpenSSH_5.1p1 Debian-5 pat OpenSSH_5* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.0 debug1: Miscellaneous failure Cannot resolve network address for KDC in requested realm debug1: Miscellaneous failure Cannot resolve network address for KDC in requested realm debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP Connection closed by 69.163.227.82

  Read the article

• Would an invalid certificate cause an 0x8004010F sync error?

  - by hydroparadise

  We just migrated from Exchange 2003 to 2007 which was a combo primary AD/DNS server and it has not gone smoothly. We are now down to getting a new certificate (a bureaucratic process thats out of my hands) and users getting the 0x8004010F sync issue. We are only using Outlook 2007 as our email client and the sync error appears exactly as so: 9:21:44 Synchronizer Version 12.0.6562 9:21:44 Synchronizing Mailbox '<User>' 9:21:44 Done 9:21:44 Microsoft Exchange offline address book 9:21:44 0X8004010F Now, I have read a number of technet articles on this issue anywhere from adding an A record in the DNS for autodiscover.domain.com to syncing the old OAD to the new OAD. In otherwords, theres lots of thing to try, but trial and error at this point might be hazardous to ther server's health and I am trying to narrow down the list of things to try. What has me thinking that the sync error could be related to the certificate is an event error message that says the following: Microsoft Exchange could not find a certificate that contains the domain name mail.ccufl.org in the personal store on the local computer. Therefore, it is unable to support the STARTTLS SMTP verb for the connector Internet Mail with a FQDN parameter of mail.ccufl.org. If the connector's FQDN is not specified, the computer's FQDN is used. Verify the connector configuration and the installed certificates to make sure that there is a certificate with a domain name for that FQDN. If this certificate exists, run Enable-ExchangeCertificate -Services SMTP to make sure that the Microsoft Exchange Transport service has access to the certificate key. I am not fully clear on how the Exchange Transport Service is related to Syncronization, but my hunch is that it probably not related to there not being a valid certificate. So to recap, would an invalid certificate cause an 0x8004010F sync error?

  Read the article

• Sun Grid Engine (SGE) / limiting simultaneous array job sub-tasks

  - by wfaulk

  I am installing a Sun Grid Engine environment and I have a scheduler limit that I can't quite figure out how to implement. My users will create array jobs that have hundreds of sub-tasks. I would like to be able to limit those jobs to only running a set number of tasks at the same time, independent of other jobs. Like I might have one array job that I want to run 20 tasks at a time, and another I want to run 50 tasks at a time, and yet another that I'm fine running without limit. It seems like this ought to be doable, but I can't figure it out. There's a max_aj_instances configuration option, but that appears to apply globally to all array jobs. I can't see any way to use consumable resources, as I'd need a "complex attribute" that is per-job, and that feature doesn't seem to exist. It didn't look like resource quotas would work, but now I'm not so sure of that. It says "A resource quota set defines a maximum resource quota for a particular job request", but it's unclear if an array job's sub-tasks' resource requests will be aggregated for the purposes of the resource quota. I'm going to play with this, but hopefully someone already knows outright.

  Read the article

• Apache22 on FreeBSD - Starts, does not respond to requests

  - by NuclearDog

  Hey folks! I'm running Apache 2.2.17 with the peruser MPM on FreeBSD 8.2-RC1 on Amazon's EC2 (so it's XEN). It was installed from ports. My problem is that, although Apache is running, listening for, and accepting connections, it doesn't actually respond to any or show them in the log at all. If I telnet to the port it's listening on and type out an HTTP request: GET / HTTP/1.1 Host: asdfasdf And hit enter a couple of times, it just sits there... Nothing. No response requesting with a browser either. There doesn't appear to be anything helpful in the error log: [Sun Jan 09 16:56:24 2011] [warn] Init: Session Cache is not configured [hint: SSLSessionCache] [Sun Jan 09 16:56:25 2011] [notice] Digest: generating secret for digest authentication ... [Sun Jan 09 16:56:25 2011] [notice] Digest: done [Sun Jan 09 16:56:25 2011] [notice] Apache/2.2.17 (FreeBSD) mod_ssl/2.2.17 The access log stays empty: root:/var/log# wc httpd-access.log 0 0 0 httpd-access.log root:/var/log# I've tried with accf_http and accf_data both enabled and disabled, and with both the stock configuration and my customized config. I also tried uninstalling apache22-peruser-mpm and just installing straight apache22... Still no luck. I tried removing all of the LoadModule lines from httpd.conf and just re-enabled the ones that were necessary to parse the config. Ended up with only the following loaded: root:/usr/local/etc/apache22# /usr/local/sbin/apachectl -M Loaded Modules: core_module (static) mpm_peruser_module (static) http_module (static) so_module (static) authz_host_module (shared) log_config_module (shared) alias_module (shared) Syntax OK root:/usr/local/etc/apache22# Same results. Apache is definitely what's listening on port 80: root:/usr/local/etc/apache22# sockstat -4 | grep httpd root httpd 43789 3 tcp4 6 *:80 *:* root httpd 43789 4 tcp4 *:* *:* root:/usr/local/etc/apache22# And I know it's not a firewall issue as there is nothing running locally, and connecting from the local box to 127.0.0.1:80 results in the same issue. Does anyone have any idea what's going on? Why it would be doing this? I've exhausted all of my debugging expertise. :/ Thanks for any suggestions!

  Read the article

• How to convert an MKV to AVI with minimal loss

  - by Linux Jedi

  To convert an MKV to AVI, I do two things. The first thing I do is this: ffmpeg -i filename.mkv -vcodec copy -acodec copy output.avi This converts the MKV to an AVI, but the problem is that the video does not play smoothly for some reason. That's fine, because if I do one more thing it gets fixed: ffmpeg -i output.avi -vcodec mpeg4 -b 4000k -acodec mp2 -ab 320k converted.avi After I do this then the file plays without problem. I had success doing it this way for one file, but then I tried it on another file, and there is a slight, but noticeable loss in video quality. This is the output I get when doing the second step: FFmpeg version 0.6.1, Copyright (c) 2000-2010 the FFmpeg developers built on Dec 29 2010 18:02:10 with gcc 4.2.1 (Apple Inc. build 5664) configuration: libavutil 50.15. 1 / 50.15. 1 libavcodec 52.72. 2 / 52.72. 2 libavformat 52.64. 2 / 52.64. 2 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0.11. 0 / 0.11. 0 Seems stream 0 codec frame rate differs from container frame rate: 359.00 (359/1) -> 29.92 (359/12) Input #0, avi, from 'output.avi': Metadata: ISFT : Lavf52.64.2 Duration: 00:04:17.21, start: 0.000000, bitrate: 3074 kb/s Stream #0.0: Video: mpeg4, yuv420p, 704x480 [PAR 229:189 DAR 5038:2835], 29.92 fps, 29.92 tbr, 29.92 tbn, 359 tbc Stream #0.1: Audio: vorbis, 48000 Hz, stereo, s16 Output #0, avi, to 'nidome_no_kanojo.avi': Metadata: ISFT : Lavf52.64.2 Stream #0.0: Video: mpeg4, yuv420p, 704x480 [PAR 229:189 DAR 5038:2835], q=2-31, 4000 kb/s, 29.92 tbn, 29.92 tbc Stream #0.1: Audio: mp2, 48000 Hz, stereo, s16, 320 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 I just used arbitrarily large settings on the second step and it worked nicely before but not in this case. What settings should I use?

  Read the article

• nmap installation issue

  - by daasf

  vanilla centos with latest updates, installed gcc, and after ./configure:.... Configuration complete. Type make (or gmake on some *BSD machines) to compile. [root@winxp nmap-5.51]# make Makefile:375: makefile.dep: No such file or directory g++ -MM -I./liblua -I./libdnet-stripped/include -I./libpcre -I./libpcap -I./nbase - I./nsock/include -DHAVE_CONFIG_H -DNMAP_NAME=\"Nmap\" -DNMAP_URL=\"http://nmap.org\" - DNMAP_PLATFORM=\"x86_64-unknown-linux-gnu\" -DNMAPDATADIR=\"/usr/local/share/nmap\" - D_FORTIFY_SOURCE=2 main.cc nmap.cc targets.cc tcpip.cc nmap_error.cc utils.cc idle_scan.cc osscan.cc osscan2.cc output.cc payload.cc scan_engine.cc timing.cc charpool.cc services.cc protocols.cc nmap_rpc.cc portlist.cc NmapOps.cc TargetGroup.cc Target.cc FingerPrintResults.cc service_scan.cc NmapOutputTable.cc MACLookup.cc nmap_tty.cc nmap_dns.cc traceroute.cc portreasons.cc xml.cc nse_main.cc nse_utility.cc nse_nsock.cc nse_dnet.cc nse_fs.cc nse_nmaplib.cc nse_debug.cc nse_pcrelib.cc nse_binlib.cc nse_bit.cc > makefile.dep /bin/sh: g++: command not found make: *** [makefile.dep] Error 127 [root@winxp nmap-5.51]# yum install g++ -y Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * addons: mirror.ash.fastserv.com * base: centos.mirror.choopa.net * extras: mirror.trouble-free.net * updates: mirror.nexcess.net Setting up Install Process No package g++ available. Nothing to do [root@winxp nmap-5.51]#

  Read the article

• Connection refused in ssh tunnel to apache forward proxy setup

  - by arkascha

  I am trying to setup a private forward proxy in a small server. I mean to use it during a conference to tunnel my internet access through an ssh tunnel to the proxy server. So I created a virtual host inside apache-2.2 running the proxy, the proxy_http and the proxy_connect module. I use this configuration: <VirtualHost localhost:8080> ServerAdmin xxxxxxxxxxxxxxxxxxxx ServerName yyyyyyyyyyyyyyyyyyyy ErrorLog /var/log/apache2/proxy-error_log CustomLog /var/log/apache2/proxy-access_log combined <IfModule mod_proxy.c> ProxyRequests On <Proxy *> # deny access to all IP addresses except localhost Order deny,allow Deny from all Allow from 127.0.0.1 </Proxy> # The following is my preference. Your mileage may vary. ProxyVia Block ## allow SSL proxy AllowCONNECT 443 </IfModule> </VirtualHost> After restarting apache I create a tunnel from client to server: #> ssh -L8080:localhost:8080 <server address> and try to access the internet through that tunnel: #> links -http-proxy localhost:8080 http://www.linux.org I would expect to see the requested page. Instead a get a "connection refused" error. In the shell holding open the ssh tunnel I get this: channel 3: open failed: connect failed: Connection refused Anyone got an idea why this connection is refused ?

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Any ideas? Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp2 KB896256 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• PC won't PXE boot to WDS/MDT with Dell Optiplex 755

  - by Moman10

  I am trying to set up a basic MDT solution. I have set one up in the past at a previous job and it worked flawlessly, however here I'm running into a problem and am having no luck getting around it. I've installed Windows Server 2012 and MDT 2013, along with adding on the WDS role. I haven't configured much outside of the defaults for WDS, basically just set PXE response to respond to all clients (and unchecked admin approval). This machine does not run a DHCP server. I looked on the DHCP scope of our DHCP server, it shows options 66/67 checked and the server name of the WDS server is in there as well. I didn't add this but I assume it was put on during the install process (I believe I had to manually make some adjustments at my old job for this). The PC I have is a Dell Optiplex 755. I have enabled the onbard NIC w/PXE boot option in BIOS and attempted to boot. I get a "TFTP...." error but nothing offering out a DHCP address like I'm used to. In my previous job it pretty much worked right out of the box. I've verified that PortFast is enabled on the port and I've tried a couple different PCs (but both are the same model, only model I have to work with). No matter what, I get the same error. The subnet the PC is in is a different subnet than where the WDS server is sitting, but there are IP helper statements on the switch and the PCs can get regular DHCP addresses just fine from the DHCP server, just doesn't seem to get offered out a PXE boot option. I don't know if the problem is a configuration with the server or the PC itself...but after a few days of Googling I'm running out of ideas. Does anyone have a good idea of something it may be?

  Read the article

• Why I cannot copy install.wim from Windows 7 ISO to USB (in linux env)

  - by fastreload

  I need to make a USB bootable disk of Windows 7 ISO. My USB is formatted to NTFS, ISO is not corrupt. I can copy install.wim elsewhere but I cannot copy it to USB. I even tried rsync. rsync error sources/install.wim rsync: writefd_unbuffered failed to write 4 bytes to socket [sender]: Broken pipe (32) rsync: write failed on "/media/52E866F5450158A4/sources/install.wim": Input/output error (5) rsync error: error in file IO (code 11) at receiver.c(322) [receiver=3.0.8] Stat for windows.vim File: `X15-65732 (2)/sources/install.wim' Size: 2188587580 Blocks: 4274600 IO Block: 4096 regular file Device: 801h/2049d Inode: 671984 Links: 1 Access: (0664/-rw-rw-r--) Uid: ( 1000/ umur) Gid: ( 1000/ umur) Access: 2011-10-17 22:59:54.754619736 +0300 Modify: 2009-07-14 12:26:40.000000000 +0300 Change: 2011-10-17 22:55:47.327358410 +0300 fdisk -l Disk /dev/sdd: 8103 MB, 8103395328 bytes 196 heads, 32 sectors/track, 2523 cylinders, total 15826944 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdd1 * 32 15826943 7913456 7 HPFS/NTFS/exFAT hdparm -I /dev/sdd: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ATA device, with non-removable media Model Number: UF?F?A????U]r???U u??tF?f?`~ Serial Number: ?@??~| Firmware Revision: ????V? Media Serial Num: $I?vnladip raititnot baelErrrol aoidgn Media Manufacturer: o eparitgns syetmiM Standards: Used: unknown (minor revision code 0x0c75) Supported: 12 8 6 Likely used: 12 Configuration: Logical max current cylinders 17218 0 heads 0 0 sectors/track 128 0 -- Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 0 MBytes device size with M = 1000*1000: 0 MBytes cache/buffer size = unknown Capabilities: IORDY(may be)(cannot be disabled) Queue depth: 11 Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 0 Current = ? Recommended acoustic management value: 254, current value: 62 DMA: not supported PIO: unknown * reserved 69[0] * reserved 69[1] * reserved 69[3] * reserved 69[4] * reserved 69[7] Security: Master password revision code = 60253 not supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 71112min for SECURITY ERASE UNIT. 172min for ENHANCED SECURITY ERASE UNIT. Integrity word not set (found 0xaa55, expected 0x80a5)

  Read the article

• HTTPS and Certification for dummies

  - by Poxy

  I had never used https on a site and now want to try it. I did some research, but not sure that I understood everything. Answers and corrections are greatly appreciated. Here we go: To use https I need to generate ‘private’ and ‘public’ keys for the web server I use. In my case it’s apache (manual: http://httpd.apache.org/docs/2.0/ssl/ssl_faq.html) Https protocol should be bind to port 443. Q: How to do it? Is it done by default? Where can I check configuration? Aplying https. Q: If I see https in browser does it mean that the data traffic on the page IS encrypted? Any form on the page would submit data via https? Though all the data gonna be encrypted, the browsers would still show ugly red messages. This is just because they do not know anything about my certificate. They have about a hundred certificates pre-installed but mine is not one of them, obviously. But the data IS encrypted by https. If I want browsers to recognize my certificate, I would need to have it signed by one of the certification authorities (ca) that has its certificate pre-installed (e.g. thawte, geotrust, rapidssl etc). UPD: To reed about ssl/tsl: The First Few Milliseconds of an HTTPS Connection, I found it very informative. Examples for PHP (openssl.org) of how to make use of ssl/tsl on the server side are published here.

  Read the article

• vyatta Server Reboots by itself

  - by Fernando

  I have an issue regarding some hardware, maybe you can help me. First, I set up a Supermicro Superserver SYS-5016I-NTF with a Intel Xeon X3470 and 4 GB of Ram with a Hotlava Card Tambora 64G4 with Intel Chipset 82599EB and 4x10G SPF+ ports. Installed Vyatta community edition 6.3. I used it as router making BGP connections with 2 operators. No load at all, temp ranges normal. But the issue is that it reboots by itself in a ramdom way. Not very often, once every few days. But it is unacceptable for production purposes. So I try to test on different hardware, and installed Vyatta community edition 6.3 on a Dell PowerEdge 2950, with Xeon(R) E5345 @ 2.33GHz and 4 GB of Ram. Same Vyatta configuration as Supermicro Server. With same hotlava Card model ( I bought two of them ) Well I have reboots with this equipment as well. Same frecuency as above. I have checked syslog no strange logs until boot process starts to be logged. So it seems server reboot suddenly. I have installed latest driver for the chipset of the Hotlava card. Servers are placed in a datacenter with UPS So finally two things in common in both servers: Hotlava Card. Someone with issues with this card, or the chipset?? Could be it this card?? Vyatta 6.3 community edition. I don't thing is the problem. Is a regular Debian with packages to glue together different services. Or maybe is something I am missing. Andy ideas, suggestions?? Thank you very much... Fernando

  Read the article

• Sending mail through local MTA while domain MX records point to Google Apps

  - by Assaf

  My domain's email is managed by Google Apps, so that domain users get Gmail and Calendar, etc. But I also want to be able to send applicative notifications to users outside the domain via email (e.g. "some commented on your post", and so on). However, if I try to send email through code I get blocked by Gmail after a few emails. I send marketing email through MailChimp, to minimize the risk of appearing as spam to my users (one-click unsubscribe, etc.). But I can't send applicative message in this way. I want to install a local MTA (my server runs Ubuntu), but I'm not sure what anti-spam measures I need to implement so that receiving MTAs don't think it's a spam server. What's stopping anyone from setting up a mail server and sending emails using my domain name? AFAIK it's the DNS records that show the MTA's address actually belongs to the domain. But my understanding of this is rather superficial, so someone please correct me if I'm wrong. But what sort of DNS configuration do I need to put in place so that I don't get blacklisted (assuming I don't actually spam anyone)? The MX records already point to Google, and I'd like to keep it this way. So do I just need to define an A record for my internal mail server? Should it show email as coming from a sub-domain, so as not to conflict with the bare domain being managed by google? Edit: Does the following SPF record make sense if I want email from my domain name to be sent by either google's servers or any server with a dns name ending with mydomain.com? "v=spf1 ptr mx:google.com mx:googlemail.com ~all" How should I set up reverse DNS for my server? If I have an A record that points mailsender.mydomain.com to my MTA's ip address, does it mean that reverse lookup will only allow emails sent from [email protected]?

  Read the article

• Server 2012, Jumbo Frames - should I expect problems?

  - by TomTom

  Ok, this sound might stupid - but is there any negative on just enabling jumbo frames in practice? From what I understand: Any switch or ethernet adapter that sees a jumbo frame it can not handle will just drop it. TCP is not a problem as max frame size is negotiated in the setinuo phase. UCP is a theoretical problem as a server may just send a LARGE UDP packet that gets dropped on the way. Practically though, as UDP is packet based, I do not really think any software WOULD send a UDP packet larger than 1500 bytes net without app level configuration changes - at least this is how I do my programming, as it is quite hard to get a decent MTU size for that without testing yourself, so you fall back in programming to max 1500 packets. The network in question is a standard small business network - we upgraded now from a non managed 24 port switch to a 52 port switch with 4 10g ports (netgear - quite cheap) and will mov a file server to 10g for also ISCSI serving. All my equipment on the Ethernet level can handle minimum 9000 bytes and due to local firewalls I really want to get packets larger (less firewall processing), but the network is also NAT'ed to the internet. On top, different machines move around (download) large files (multi gigabyte area) quite often for processing. The question is - can I expect problems when I just enable jumbo frames? Again, this is not totally ignorance - I just don't see programs sending more than 1500 byte UDP packets (if that is a practical problem please tell me) and for TCP the MTU is negotiated anyway. if there is a problem I can move to a dedicated VLAN, but this has it's own shares of problems as basically most workstations must then be on both VLAN's.

  Read the article

• Kickstart: Serve dynamic kickstart images via a CGI or PHP script?

  - by Stefan Lasiewski

  I'd like to kickstart a couple dozen RHEL6/SL6 servers. However, some of these servers are different and I don't want to create a new ks.cfg file for each class of server. Are there any products which can generate a Kickstart file dynamically on the fly, from a template? For example, if I append a line like this to the KERNEL: APPEND ks=http://192.168.1.100/cgi-bin/ks.cgi Then the script ks.cgi can determine what host this is (Via the MAC address), and print out Kickstart options which are appropriate for that host. I could optionally override some options by passing parameters to the script, like this: APPEND ks=http://192.168.1.100/cgi-bin/ks.cgi?NODETYPE=production&IP=192.168.2.80 After we kickstart the server, we activate Cfengine/Puppet on this system and manage the system using our favorite Configuration Management product. We're experimenting with xCAT but it is proving too cumbersome. I've looked into Cobbler, but I'm not sure it does this. Update: A roll-your-own solution is discussed in the O'Reilly book: Managing RPM-Based Systems with Kickstart and Yum, Chapter 3. Customizing Your Kickstart Install Dynamic ks.cfg, which echos some of the comments in this thread: To implement such a tool is beyond the scope of this Short Cut, but I can walk through the high-level design. Any such solution would mix a data store (the things that change) with a templating solution (the things that don’t change). The data store would hold the per-machine data, such as the IP address and hostname. You would also need a unique identifier, perhaps the hostname, such that you could pick up a given machine’s data. The data store could be a flat file, XML data, or a relational database such as PostgreSQL or MySQL. In turn, to invoke the system, you pass a machine’s unique identifier as a URL parameter. For example: boot: linux ks=http://your.kickstart.server/gen_config?host-server25 In this example, the CGI (or servlet, or whatever) generates a ks.cfg for the machine server25. But where, oh where, is the code for ks.cgi?

  Read the article

• Supervisord doesn't stop nginx process

  - by Lennart Regebro

  I'm using Supervisor a lot, and in this project I have an nginx process managed by Supervisord. The relevant parts of the configuration is this: [supervisord] logfile=/home/projects/eceee-web/prod/var/log/supervisord.log logfile_maxbytes=5MB logfile_backups=10 loglevel=info pidfile=/home/projects/eceee-web/prod/var/supervisord.pid ; childlogdir=/home/projects/eceee-web/prod/var/log nodaemon=false ; (start in foreground if true;default false) minfds=1024 ; (min. avail startup file descriptors;default 1024) minprocs=200 ; (min. avail process descriptors;default 200) directory=/home/projects/eceee-web/prod [program:nginx] command = /home/projects/eceee-web/prod/bin/nginx redirect_stderr = true autostart= true autorestart = true directory = /home/projects/eceee-web/prod stdout_logfile = /home/projects/eceee-web/prod/var/log/nginx-stdout.log stderr_logfile = /home/projects/eceee-web/prod/var/log/nginx-stderr.log The /home/projects/eceee-web/prod/bin/nginx command will start nginx in the foreground, it does not deamonify itself. Still, stopping it will fail: supervisorctl stop nginx Will not give any answer, but the process will continue. Any idea what? This is on OS X Darwin, with Supervisor 3.0a9 and nginx 0.7.65.

  Read the article

• How to prioritize openvpn traffic?

  - by aditsu

  I have an openvpn server, with one network interface. VPN traffic is extremely slow. I tried to do traffic control with this configuration (currently): qdisc del dev eth0 root qdisc add dev eth0 root handle 1: htb default 12 class add dev eth0 parent 1: classid 1:1 htb rate 900mbit #vpn class add dev eth0 parent 1:1 classid 1:10 htb rate 1500kbit ceil 3000kbit prio 1 #local net class add dev eth0 parent 1:1 classid 1:11 htb rate 10mbit ceil 900mbit prio 2 #other class add dev eth0 parent 1:1 classid 1:12 htb rate 500kbit ceil 1000kbit prio 2 filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip sport 1194 0xffff flowid 1:10 filter add dev eth0 protocol ip parent 1:0 prio 2 u32 match ip dst 192.168.10.0/24 flowid 1:11 qdisc add dev eth0 parent 1:10 handle 10: sfq perturb 10 qdisc add dev eth0 parent 1:11 handle 11: sfq perturb 10 qdisc add dev eth0 parent 1:12 handle 12: sfq perturb 10 But it's still extremely slow. I have an imaps connection that keeps transferring data continuously (I successfully limited the rate) but with openvpn I can't seem to get more than about 100kbit/s The internet connection speed is about 3mbit/s (symmetric) What could be the problem? Does the sport filter work for udp?

  Read the article

• Display maintenance site to requesters based on their IP address

  - by user64294

  Hi all. I would like to set a special configuration in our apache web server. I would like to display sites to the users according to their IP addresses. We plan to upgrade our web sites. During the upgrade we'll put a maintenance site: so all the users which will connect to our web sites will get this site. There are 200 websites affected by the upgrade, so I don't want to change apache settings for each one. In order to test the upgrade i need to set apache to let only my IP address to access to asked site. If my IP address is a.b.c.d and if i ask for test.com i want to see it. but all other users, having a different IP address, should get the maintenane site even if they look for test.com. Our webserver is hosted out of the office (ovh.com france). The testers are the developers at our office and me. We can take some sites and enable them for test in which we implement IP restrictions in each website: the idea is on these websites, if the visitor's IP address is different from our office IP address we redirect this visitor to our maintenance website else we display the website. Is there a way to do this? Thank you.

  Read the article

• postfix smtp_fallback_relay for deferred messages to a single domain

  - by EdwardTeach

  I use Postfix to send messages to a mail server outside my organization which frequently rejects/defers my mail. My Postfix server sees that these messages are deferred and tries again, eventually getting through. Final delivery can take up to an hour, which makes my users unhappy. In comparison, mail from my Postfix server to other hosts works normally. I have now found out about a second, unofficial MX for this domain that does not reject/defer mail. This second MX does not appear when doing a DNS MX query for the domain. Therefore, for the problem domain I would like to use this second MX as a fallback. That is: whenever mail is deferred by the primary MX, try again on the unofficial second MX. I see that there is already a postfix configuration "smtp_fallback_relay". However the documentation seems to indicate that I can not restrict usage of the fallback to a single domain. The documentation also doesn't mention deferred message handling. So is there a way to configure a single-domain, deferred-retry fallback host in Postfix? For reference, I am including my postconf output (the host names and ip addresses are fake): alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/etc/postfix/legacy_mailman, ldap:/etc/postfix/ldap-aliases.cf append_dot_mydomain = no biff = no config_directory = /etc/postfix default_destination_concurrency_limit = 2 inet_interfaces = all inet_protocols = all local_destination_concurrency_limit = 2 local_recipient_maps = $alias_maps mailbox_size_limit = 0 mydestination = myhost.my.network, localhost.my.network, localhost, my.network myhostname = myhost.my.network mynetworks = 127.0.0.0/8, [::ffff:127.0.0.0]/104, [::1]/128, 10.10.10.0/24 myorigin = my.network readme_directory = no recipient_delimiter = + relay_domains = $mydestination relayhost = smtp_fallback_relay = the.problem.host smtp_header_checks = smtpd_banner = $myhostname ESMTP $mail_name virtual_alias_maps = hash:/etc/postfix/virtual

  Read the article

• Printing on Windows 8 with PDF viewer (Adobe Reader) from network

  - by Bongo

  i have a problem with the Adobe Reader 8, but the problem seems to be equally bad with other pdf viewers. Here is the configuration: My PDF viewer is located on network drive "Z:" which is the network adress \dgs-main\progs. I tried to start the adobe reader from here - \\dgs-main\progs\Adobe\Reader 8.0\Reader\AcroRd32.exe and open the PDF from here - C:\Users\ServiceDesk\AppData\Local\Temp\GeneratedPDF.pdf The problem is as follows, if i open the PDF with a local PDF viewer everything works fine and i can print the document. If i open the PDF with the Network PDF viewer then it opens, but printing is impossible. The error message states: "Unable to start print job. Is printer available?" As mentioned above, it works with a local pdf viewer. In both cases i use the same printer. The Printer is a network printer but even with a local printer it fails. The error occurs only on Windows 8 machines. On windows 7 it works fine. I Hope somebody can tell me what the problem is. Thanks in advance and have a fine day.

  Read the article

• Dell XPS 15 L502X hard drive Partition

  - by Mohan Gajula

  I have a situation here. I got my new Dell XPS 15 Laptop. The configuration of hard drive is as below : Volume 1: (OEM Partition): 133MB Volume 2: OS (C:): 685.25 GB Volume 3: Recovery : 13.25 GB Now, I am trying to re-partition my C Drive to have a C: drive with 100 GB and a new drive with 585 GB. Earlier, I tried using the Windows 7 Disk Management to shrink and extend the volume. That lead to the OS and hard drive not working. Dell Tech support tried to fix the issue, but they were not able to fix the issue online. Later a Dell Technician arrived my place, and replaced the hard drive with a new hard drive. Please help me re-partition the C: Drive with 100 GB, and new D drive with 585 GB. I don't want to lose my Recovery Partition. SOLUTION As Suggested by KCotreau below , I have done exactly. I have resized the C drive to 100 GB. And then applied the changes. Windows got restarted. On the boot screen, the partition was taking place. It took around 30 mins ( approx. ). Once after restart, I can see my C drive is 100 GB. Now opened the Easeus again. And created a new partition for the free space ( 585 GB ) this took 10 seconds to create. Here goes the screenshot after partitioning. Thanks to KCotreau. You are amazing.

  Read the article

• Can't ping through default gateway

  - by Andrew G.H.

  I have the following configuration: Routing table on M3 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.3.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 Routing table on M1 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 So basically M3's gateway is M1, and M1's gateway is M2's wireless internet interface. If I ping 8.8.8.8 from M1, everything is ok, replies are received. Pinging from M1 to M3 and viceversa is also possible. I have configured M1 as gateway trafic forwarder using firestarter package and stopped firewall with it. iptables policies are ACCEPT for everything. Problem: I have tried ping-ing ip 8.8.8.8 from M3 but without success. What could be the source of this problem?

  Read the article

• Setting up port forwarding for web server

  - by reyjavikvi

  This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

  Read the article

< Previous Page | 486 487 488 489 490 491 492 493 494 495 496 497  | Next Page >