Search Results

Search found 29317 results on 1173 pages for 'device control'.

Page 532/1173 | < Previous Page | 528 529 530 531 532 533 534 535 536 537 538 539  | Next Page >

• how to setup kismet.conf on Ubuntu

  - by Registered User

  I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

  Read the article

• Harddisk formatting with dd return error

  - by Usman Ajmal

  Hi, I tried to format my harddisk (160 GB) with the following command dd if=/dev/zero of=/dev/sda After some 3 hours, following error came up: dd: writing to '/dev/sda' : No space left on device 312581809+0 records in 312581808+0 records out 160041885696 bytes (160 GB) copied, 10708.3 s, 14.9 MB/s Any idea what went wrong?

  Read the article

• network manager in opensuse 11.2

  - by user30780

  hello.my network manager in opensuse 11.2 kde environment not working.after clicking.nothing action is being takes place.what should i do.i have to connect to the internet thriugh this.i have airtel macromax usb plug and play device

  Read the article

• Software Raid 10 corrupted superblock after dual disk failure, how do I recover it?

  - by Shoshomiga

  I have a software raid 10 with 6 x 2tb hard drives (raid 1 for /boot), ubuntu 10.04 is the os. I had a raid controller failure that put 2 drives out of sync, crashed the system and initially the os didnt boot up and went into initramfs instead, saying that drives were busy but I eventually managed to bring the raid up by stopping and assembling the drives. The os booted up and said that there were filesystem errors, I chose to ignore because it would remount the fs in read-only mode if there was a problem. Everything seemed to be working fine and the 2 drives started to rebuild, I was sure that it was a sata controller failure because I had dma errors in my log files. The os crashed soon after that with ext errors. Now its not bringing up the raid, it says that there is no superblock on /dev/sda2, even if I assemble manually with all the device names. I also did a memtest and changed the motherboard in addition to everything else. EDIT: This is my partition layout Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0009c34a Device Boot Start End Blocks Id System /dev/sdb1 * 2048 511999 254976 83 Linux /dev/sdb2 512000 3904980991 1952234496 83 Linux /dev/sdb3 3904980992 3907028991 1024000 82 Linux swap / Solaris All 6 disks have the same layout, partition #1 is for raid 1 /boot, partition #2 is for raid 10 far plan, partition #3 is swap, but sda did not have swap enabled EDIT2: This is the output of mdadm --detail /dev/md1 Layout : near=1, far=2 Chunk Size : 64k UUID : a0feff55:2018f8ff:e368bf24:bd0fce41 Events : 0.3112126 Number Major Minor RaidDevice State 0 8 34 0 spare rebuilding /dev/sdc2 1 0 0 1 removed 2 8 18 2 active sync /dev/sdb2 3 8 50 3 active sync /dev/sdd2 4 0 0 4 removed 5 8 82 5 active sync /dev/sdf2 6 8 66 - spare /dev/sde2 EDIT3: I ran ddrescue and it has copied everything from sda except a single 4096 byte sector that I suspect is the raid superblock EDIT4: Here is some more info too long to fit here lshw: http://pastebin.com/2eKrh7nF mdadm --detail /dev/sd[abcdef]1 (raid1): http://pastebin.com/cgMQWerS mdadm --detail /dev/sd[abcdef]2 (raid10): http://pastebin.com/V5dtcGPF dumpe2fs of /dev/sda2 (from the ddrescue cloned drive): http://pastebin.com/sp0GYcJG I tried to recreate md1 based on this info with the command mdadm --create /dev/md1 -v --assume-clean --level=10 --raid-devices=6 --chunk=64K --layout=f2 /dev/sda2 missing /dev/sdc2 /dev/sdd2 missing /dev/sdf2 But I can't mount it, I also tried to recreate it based on my initial mdadm --detail /dev/md1 but it still doesn't mount It also warns me that /dev/sda2 is an ext2fs file system but I guess its because of ddrescue

  Read the article

• Symantec Gateway Security 320 VPN/Port Forwarding trouble

  - by Owl

  How do I check to see if port forward is enabled with one of my dynamic tunnels on this device? I'm having trouble using a feature in our software that requires a vpn to be used. My firewalls shows it as connected but I'm unable to ping the subnet ip. Our software vendor told me that port forwarding might be causing this problem, but I didn't set up this network I'm on and I don't fully know symantec hardware.

  Read the article

• Windows 7 search does not return results from indexed folders

  - by Dilbert

  I am experiencing this issue over and over again and I just cannot seem to find the answer. It doesn't make sense, but search simply does not return results from folders that certainly have these files inside. It's weird that this technology exists for more than 5 years now (it could be added to Windows XP as an addon), and they still haven't got it right. My folder contains 10 image files with .png extensions. Two scenarios: Scenario 1: I exclude the folder using Indexing options. Search works. Scenario 2: I turn on indexing for this folder. Search does not work. Of course, Agent Ransack returns results every time. When I check Advanced options for the Indexing options inside control panel, .png files are checked in the File Types tab, using the "File Properties filter". What's the deal with this? [Edit] To clarify, this doesn't happen with all folders, but does with more than one. For the "problematic" folders, even *.* doesn't return a single result. I found some advice to clear the archive and readonly attributes for all files (doesn't make sense, but hey), but it didn't work. Indexing status in Control panel is: Indexing complete. 100,000 items indexed. Folder is included in the list. File types list contains the .png extension (although it doesn't work with any filter, not even *.*).

  Read the article

• allow infiniband for non root users

  - by user1219721

  I got Infiniband running on RHEL 6.3 [root@master ~]# ibv_devinfo hca_id: mthca0 transport: InfiniBand (0) fw_ver: 4.7.927 node_guid: 0017:08ff:ffd0:6f1c sys_image_guid: 0017:08ff:ffd0:6f1f vendor_id: 0x08f1 vendor_part_id: 25208 hw_ver: 0xA0 board_id: VLT0060010001 phys_port_cnt: 2 port: 1 state: PORT_ACTIVE (4) max_mtu: 2048 (4) active_mtu: 2048 (4) sm_lid: 2 port_lid: 3 port_lmc: 0x00 link_layer: InfiniBand port: 2 state: PORT_DOWN (1) max_mtu: 2048 (4) active_mtu: 512 (2) sm_lid: 0 port_lid: 0 port_lmc: 0x00 link_layer: InfiniBand but it's only working as root. when trying from a non-super user, I got nothing : [nicolas@master ~]$ ibv_devices device node GUID ------ ---------------- mthca0 001708ffffd06f1c So, how to allow regular users to use infiniband ?

  Read the article

• MacBook Pro 13 inch trackpad: Makes very annoying sounds when clicked

  - by Alex

  Hi, recently my trackpad on my MacBook Pro 13 inch has been making really annoying sounds when pressed. Almost like there's something (possibly sticky) under there. I do not recall ever spilling on this device and am wondering what's up. I don't want to take it apart because that voids all warranties with Apple. Any suggestions? Thanks.

  Read the article

• Office Compatibility Pack and File Permissions

  - by hymie

  MS isn't my thing, so I hope somebody can give me a pointer. We have a Windows domain, with a Server-2003-SP1-Enterprise file server. One of the specific files is a MS Excel 2007 (XLSX) file created by user LK. In the "Security" preferences setting, about a half-dozen users (including me) have access to this file. LK is the owner and has "full control", while the rest of us have "Read" , "Read & Execute", and "Write" permission. LK is also the owner of the directory that this file resides in. I don't know if that's relevant. So far so good. My desktop machine has Windows XP SP3 , and Excel 2003 SP3 , and the "Office Compatibility Pack" which lets me read and write the new XLSX files. However, whenever I write the file, the permissions are changed. The newly-written file only has permissions for LK and me, and both are "Full control" So in short, what am I doing wrong, and how should I set this up to do it right, keeping the permissions on the file that were there when I started?

  Read the article

• Logon onto shared Windows account using individual passwords?

  - by Tom

  In a networked WinXP environment, I have a computer-controlled device which I want to connect to the network, but allow various people to use. The computer must be left running and logged on at all times. My thought is to run the computer under a "shared account" which would allow each user to logon/unlock the screen using their own network password (i.e., the password for their personal account). Is this possible? Thanks, Tom

  Read the article

• No Audio from Windows XP after formatting.

  - by karthik

  Hello folks, I have reinstalled in my Windows XP machine. After it is re-isntalled the audio in my machine has failed. I have installed all the device drivers in my mother board. The Realtek Sound driver is also installed. Note: Sound is working when I test the surround settings test in my RealTek program, but unable to play any audio, tried playing both in my local machine and from the internet. Any clues to troubleshoot?

  Read the article

• Why does my Windows 7 computer wake itself up from sleep mode?

  - by AbuHamzah

  I have XPS9100 DELL desktop computer awakes out of the sleep mode without me prompting it. I have 64 bit OS Before I go to sleep I put that in sleep mode but in the morning I see its awake and I try every setting possible but could not help I have tried this command and here is what I got and I am not sure what to do. C:\Users\NAME>powercfg -lastwake Wake History Count - 1 Wake History [0] Wake Source Count - 1 Wake Source [0] Type: Wake Timer Owner: [SERVICE] \Device\HarddiskVolume3\Windows\System32\svchost.exe (wuauserv)

  Read the article

• How to remove directories from source after copying them?

  - by user55542

  I just want to move dirs. I looked successively at mv, cp and rsync, since each tool in turn didn't seem to have the option to remove directories from source after copying them. For instance, mv needs files, not dirs, when src and dst are on different devices: "inter-device move failed: src to dst; unable to remove target: Is a directory" Perhaps the simplest way to do this is by using an additional deletion cmd, although I'd prefer not to use it, since that increases risk of data loss.

  Read the article

• What permissions do I need to move a folder?

  - by isme

  In the root of my drive there exists a folder called SourceControl that contains all the working copies of all my programming projects. I would like to move the folder to my user directory (\Users\Me), but something about the permissions on the folder forbids me. I don't remember how I created the folder. When I execute the move command: MOVE \SourceControl \Users\Me I receive the following error: Access is denied. I have resolved a similar problem in the past using the Takeown utility to assign ownership of the file to me, so I tried this command next: TAKEOWN /F \SourceControl It returns the following error: ERROR: The current logged on user does not have ownership privileges on the file (or folder) "C:\SourceControl". I've just learned about the Icacls utility, which can inspect and modify file permissions. I used this command to inspect the permissions on the folder: ICACLS \SourceControl It produced this list: \SourceControl BUILTIN\Administrators:(I)(F) BUILTIN\Administrators:(I)(OI)(CI)(IO)(F) NT AUTHORITY\SYSTEM:(I)(F) NT AUTHORITY\SYSTEM:(I)(OI)(CI)(IO)(F) BUILTIN\Users:(I)(OI)(CI)(RX) NT AUTHORITY\Authenticated Users:(I)(M) NT AUTHORITY\Authenticated Users:(I)(OI)(CI)(IO)(M) I think this means that normal user accounts, like mine, have permission only to read and execute (RX) here, while administrator accounts have full control (F). I used Icacls to confer full control of the directory to my user account with this command: ICACLS \SourceControl /grant:r Me:F The command produces this output: processed file: \SourceControl Successfully processed 1 files; Failed processing 0 files Now inspection of the permissions produces this output: \SourceControl Domain\Me:(F) BUILTIN\Administrators:(I)(F) BUILTIN\Administrators:(I)(OI)(CI)(IO)(F) NT AUTHORITY\SYSTEM:(I)(F) NT AUTHORITY\SYSTEM:(I)(OI)(CI)(IO)(F) BUILTIN\Users:(I)(OI)(CI)(RX) NT AUTHORITY\Authenticated Users:(I)(M) NT AUTHORITY\Authenticated Users:(I)(OI)(CI)(IO)(M) But after this the move command still fails with the same error. Is it possible to move this folder without invoking administrator rights? If not, how should I do it as administrator?

  Read the article

• CC.NET + SVN : Server certificate issue

  - by MSI

  I am trying to setup Continuous Integration in our office. Being a puny little developer I am facing this supposedly infamous problem: " Source control operation failed: svn: OPTIONS of 'https://trunkURL': Server certificate verification failed: issuer is not trusted" So I tried the following solution - Run CC.NET service (server running as win service) using a domain account (rather than default LOCAL SYSTEMS) and accept cert permanently using command prompt under that user by using svn log/list on the repo. Doesn't help :(. I am getting the following from my artifact/log files(or dashboard) ThoughtWorks.CruiseControl.Core.CruiseControlException: Source control operation failed: svn: OPTIONS of 'https://TrunkURL': Server certificate verification failed: issuer is not trusted (https://ServerAdd) . Process command: E:\(svn.exe Path) log https://TrunkURL -r "{2010-11-08T02:12:20Z}:{2010-11-08T02:13:21Z}" --verbose --xml --no-auth-cache --non-interactive at ThoughtWorks.CruiseControl.Core.Sourcecontrol.ProcessSourceControl.Execute(ProcessInfo processInfo) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.Svn.GetModifications(IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.QuietPeriod.GetModificationsWithLogging(ISourceControl sc, IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.QuietPeriod.GetModifications(ISourceControl sourceControl, IIntegrationResult lastBuild, IIntegrationResult thisBuild) at ThoughtWorks.CruiseControl.Core.IntegrationRunner.GetModifications(IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.IntegrationRunner.Integrate(IntegrationRequest request) We are using VisualSVN Server and CC.NET for this adventure. Tips, suggestions will be highly appreciated. Thanks

  Read the article

• Windows 2003 Storage Server Hanging on Large File Transfers

  - by user25272

  In one of our offices we have a Dell PowerVault 745N NAS device which acts as the main file server. Its running 32bit Windows 2003 Storage Server SP2 with 3GB RAM. The server holds around 60 users HOME folders, which are mapped via AD. The office clients are a mix of XP SP3, Vista and Windows 7. Occasionally the server will completely hang when transferring large files. When the hang happens the console becomes unresponsive with only the mouse active and blank wallpaper. Sometimes stopping the copy frees the server, sometimes not. The hanging can last around 20 minutes. During this time other servers also become unresponsive with blank wallpaper at the console. If you do manage to get onto another server the taskbar and run commands are unresponsive. This also transcends to the client computers sometimes with explorer crashing. I'm guessing this is due to the HOME folder mapping. Eventually the NAS server with free up and everything will be back to normal. The server is configured as follows: PERC 4/DC DATA 2 - 12 SCSI HDD - RAID5 SHADOWCOPY 2 SCSI HDD - RAID1 CERC SATA DATA 11 4 SATA HDD - RAID5 OS 4 SATA HDD - RAID5 All the drivers and firmware is up to date. I've been through all the diagnostics with Dell and the hardware has come up clean including full HDD tests on the arrays. The server has NOD32 installed as the AV, but the hanging happens when it is uninstalled. There are no errors in the event log when this happens and we don't have any errors logged on any of our ProCurve switches. DNS is fine on the domain and AD from what I can tell is running happily. There are no DFS or NFS shares setup either. All the shares are standard Windows. I've unchecked the allow the computer to turn off this device to save power box under Power Management on the NIC. "Set Link Speed and Duplex to Auto-negotiate 1000 " Increased Receive Descriptors buffer from 256 to 352 (reserves more CPU resource for handling data) I've run network traces using network monitor and have found the following: 417 8.078125 {SMB:192, NbtSS:25, TCP:24, IPv4:23} 192.168.2.244 192.168.5.35 SMB SMB:R; Nt Create Andx - NT Status: System - Error, Code = (52) STATUS_OBJECT_NAME_NOT_FOUND I've tried different cabling; NICs and switch ports all with the same result. Transferring files from other servers on the domain is fine. All I haven't done is run CHKDSK on the drives to look for any file system errors. On the Vista clients I have also run netsh interface tcp set global autotuning=disabled with no result. Could it be that the server has a faulty drive or that the I/O is too much for it to handle? Any ideas why would the hang cause issues with the other servers on the LAN? Many Thanks.

  Read the article

• All FireFTP passwords gone after auto-update

  - by GitaarLAB

  For the last six months (since the Firefox madness started and they keep on taking control of my PC) I'm terrified to touch Firefox. Problem is however, I've been using it in my business (since once upon a time it was a trustworthy application with useful extensions like FireFTP) and that installation (and plugins) holds four years of information. So Firefox continually deletes my important data (by) messing up (or blocking/or worse: auto-updating) my plug-ins, even crashing my computer as a result. Today Firefox killed FireFTP by (again) autoupdating FireFTP without my permission, and I did my best to disable that nonsense in about:config). Result: none of the (over 100) FireFTP accounts can be logged on to, they suddenly all ask for a password. I do not have the time to to find all of the passwords and reconfigure FireFTP again. How can I undo the mess Firefox created once again? That is, where are the passwords, how do I downgrade? As a side-question, how can I make Firefox behave again? I'm the boss of my computer, not them! How can I once and for-all take back control and completely kill every kind of auto-update feature?

  Read the article

• Why is IIS 7.5 seeing some requests as HTTP/1.0?

  - by Zhaph - Ben Duguid

  While trying to work out why Static File Compression wasn't working on one of our IIS servers, the error was coming back as "NO_COMPRESSION_10" which translates to: Server not configured to compress 1.0 requests Looking at the requests in Fiddler, I can see that I'm requesting HTTP 1.1, but everything is being sent back as HTTP 1.0: Request (from chrome, captured via Fiddler): GET /css/reset.css HTTP/1.1 Host: [-----].com Connection: keep-alive Cache-Control: max-age=0 If-Modified-Since: Tue, 16 Oct 2012 15:04:34 GMT User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.11 (KHTML, like Gecko) Chrome/23.0.1271.95 Safari/537.11 Accept: text/css,*/*;q=0.1 Referer: http://[-----].com/ Accept-Encoding: gzip,deflate,sdch Accept-Language: en-GB,en;q=0.8,en-US;q=0.6 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Response from IIS: HTTP/1.0 200 OK Cache-Control: no-cache, no-store Pragma: no-cache Content-Type: text/html; charset=utf-8 Expires: -1 Server: Microsoft-IIS/7.5 X-AspNet-Version: 4.0.30319 X-Powered-By: ASP.NET Date: Tue, 11 Dec 2012 11:57:03 GMT Connection: close Content-Length: 108837 Other servers with the same host that I'm running this site on all respond with HTTP/1.1. How can I persuade IIS to respond with HTTP/1.1 rather than HTTP/1.0? Edit to add: Digging deeper, I can see that some responses from the server are indeed being returned compressed, so I guess really I'm trying to work out why talking to this particular server from our office seems to result in it seeing 1.0 requests, while other servers at the same co-loc don't?

  Read the article

• Samsung "Kies via Wifi" doesn't work, stuck on "Loading..."

  - by eyalb99

  When I connect my Galaxy S2 to my laptop using "Kies via Wifi" it doesn't work. On my phone it tells me it is connected, and on the laptop I can see the device "GT-I9100" under connected devices, but I see no files or anything else. When I move the mouse icon over the "GT-I9100", it writes "Loading...". I've waited long enough but nothing happens. When I connect the phone using USB cable, it works perfectly fine.

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• How can I hide my network connections in the task bar when I'm not connected?

  - by CodeSlave

  How can I hide my network connections (the PC with the red X icon on the task bar) when I'm not using a that connection. Typically, I switch back and forth between wireless and wide connections depending on my location, so I don't want to just simply disable the network device.

  Read the article

• Can Android 1.6 devices be upgraded to Android 2.x for free?

  - by TimothyP

  I'm a bit confused on what the license/deployment policy for Android is really like. Is it an open source OS in the same sense as let's say a normal Linux distro ? If I have an Android 1.6 device, can I simply install the latest version of Android on it free of charge, or is there a lot more to it ? I take it, it's not just a download and install workflow.

  Read the article

• Permanently remove/disable Touch Keyboard in Windows 8 taskbar?

  - by Sid

  I have Windows 8 (final, MSDN) on my Macbook Pro Retina. Windows 8's ongoing, continuous tantrum of insisting that it's on a tablet device is causing it to always have a touch keyboard 'icon' on the taskbar. The 'icon' is actually a toolbar and I can temporarily disable it by right clicking the taskbar and DE-selecting it. However, upon rebooting the system, it always insists on coming back and activating itself. How can I permanently disable the touch keyboard toolbar in the taskbar?

  Read the article

• backup linux that installed inside windows.

  - by behrooz

  I have Ubuntu 10.04 inside windows vista. I'm going to install Windows seven but i don't want to loose all the softwares i have downloaded. how can i backup my Linux in an external device(HDD, DVD ...) and take it back to my hard-disk(I want to install it outside the windows if possible) Is there any software doing this for me?

  Read the article

• Network connection thou a wall

  - by BCS

  I have a place where I want to set up a network connection thou a normal residential wall where I can't cut any holes. I don't want to just set up a wireless system. Does anyone make a device that you place on either side of a wall to hook up a connection? Preferably something that can do 100Mb full duplex and can't be eavesdropped on with common hardware?

  Read the article

< Previous Page | 528 529 530 531 532 533 534 535 536 537 538 539  | Next Page >