Search Results

Search found 41561 results on 1663 pages for 'linux command'.

Page 545/1663 | < Previous Page | 541 542 543 544 545 546 547 548 549 550 551 552  | Next Page >

• SSMTP to forward root@localhost mail

  - by Redconnection

  I would like to forward mail that gets sent root@localhost on multiple servers to our company admin account (e-mail is hosted on gmail) I have installed ssmtp on centos 5.5 via yum and configured it. i've also changed the last line in /etc/aliases to reflect where mail to root should go to. I've then tried sending mail to root - this gets delivered without a problem (mail -v root) I've also tried sending mail to root@localhost - this is not delivered to the specified gmail account.

  Read the article

• Libvirt/KVM in NAT: can't access from host (and can't forward)

  - by SharkWipf

  I'm trying to set up a port forward to a KVM guest, managed through Libvirt on Debian 6. The VM is running in NAT, through the "default" network. This all runs fine, the VM has full internet connection. However, the host cannot reach the vm internally. Neither ping, nc nor nmap on the NAT network give any signs of the VM. Due to this, the normal iptables forwarding rules don't work either. $ cat /etc/debian_version 6.0.5 $ libvirtd --version libvirtd (libvirt) 0.9.11.3 $ kvm --version QEMU emulator version 1.0 (qemu-kvm-1.0+dfsg-11, Debian), Copyright (c) 2003-2008 Fabrice Bellard ifconfig: eth0 Link encap:Ethernet HWaddr 54:04:a6:f1:6f:10 inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.x inet6 addr: fe80::5604:a6ff:fef1:6f10/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118902 errors:0 dropped:0 overruns:0 frame:0 TX packets:142357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13247173 (12.6 MiB) TX bytes:95163190 (90.7 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:230646 errors:0 dropped:0 overruns:0 frame:0 TX packets:230646 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204577107 (195.0 MiB) TX bytes:204577107 (195.0 MiB) virbr0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:666759 (651.1 KiB) TX bytes:400701 (391.3 KiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet6 addr: fe80::fc54:ff:fee2:d260/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:125687 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:739803 (722.4 KiB) TX bytes:6886609 (6.5 MiB)

  Read the article

• Get the MAC addresses of all the machines connected to a LAN when NO machines have got an IP address yet

  - by JtheRocker

  Here is the real scenario. I have say 4 machines not having any IP address yet connected to a switch. In one of the machines (OS=CentOS), I would install a DHCP server and would provide the other machines IP addresses. Prior to assigning them IP addresses, I need to get the MAC address of each of the machines that I would assign IP addresses to. So, my question here is how to I get the MAC addresses of all the machines connected to a switch when NO machine has got any IP address yet? It's mandatory for my use case that I won't be having any IP addresses before the MAC addresses. -Thanks

  Read the article

• Maximise network transfer speed of various applications

  - by Alex

  When using nc, scp, wget to transfer files between 2 machines on a dedicated 2Mbps link, I get speeds between 0.5 and 1 Mbps. However, when I use iperf -c 10.0.1.4 -t 20 -P 12 (for example) I can maximise the speed of the link (getting stable 2Mbps). Is there a way to make single stream transfers (such as those done by scp) to utilise all/most of the link? Some kind of tcp settings, or iptables...?

  Read the article

• Why is 'grep -i' so slow? How to do it faster for ASCII?

  - by Vi.

  Consider: $ time lzop -d < tvtropes-index.lzo | egrep -B 5 '[Dd][eE][sS][cC][eE][nN][dD] ?[Ff][rR][oO][mM]' real 0m0.438s $ time lzop -d < tvtropes-index.lzo | egrep -B 5 'descend ?from' -i real 0m11.294s Both search case insensitively. Why is the -i version so slow? How do I make grep -i fast without entering things like [iI][nN] [tT][hH][iI][sS] [wW][aA][Yy]? For example, perl -ne 'print if /descend ?from/i' works fast, but '-B 5' is not as trivial to implement as in grep (as well as other options).

  Read the article

• should i install LVM in ubuntu server?

  - by ajsie

  should i install LVM in ubuntu server? i have only one primary partition. what happens if i dont install it?

  Read the article

• Migrating to ssh key authentication; implications of adding sbin's to users $PATH

  - by ancillary

  I'm in the process of migrating to key's for authentication on my CentOS boxes. I have it all set up and working, but was a bit taken aback when I noticed service (and other things) didn't work the way I was accustomed to. Even after su'ing to root, still had to call the full path for it to work (which I assume to be expected/normal behavior). I also assume this is because there are different $PATH's for root (what I was using and am used to) and the newly created, key-using user. Specifically, I noticed the sbin's of the world missing from the user path. If I were to add those paths (/sbin/,/usr/sbin/,/usr/local/sbin) to a profile.d .sh script for this new key-loving user, would: I be opening up the system in ways I shouldn't be? I be doing something I needn't do save for reasons of laziness? I create other potential problems? Thanks.

  Read the article

• When HDD wakes up?

  - by NumberFour

  Im looking for some small script or application which could log the time when a non-system disk wakes up. I cannot identify which application or script wakes up my non-system drive (which has to be asleep until I work with it). I have already set the noatime flag, tried to use powertop and iotop to determine which application could prevent it from going to sleep - but with no result. So my plan is to set this drive asleep (hdparm -Y) and see at what time it gets regularly woken up. Thanks for any advice.

  Read the article

• Is there such a thing as a persistent ram drive?

  - by Linus

  I have a laptop with a LAMP setup. The HDD is slow, which causes my unit tests to run slowly. I was wondering whether I could mount the web root the mysql database on some kind of ramdisk. From what I have read of ramdisks, they are non-persistent. Is there anyway to create a ramdisk that writes changes to an area of the hdd when shutting down and re-mounts the ramdisk on bootup?

  Read the article

• Weird nfs performance: 1 thread better than 8, 8 better than 2!

  - by Joe

  I'm trying to determine the cause of poor nfs performance between two Xen Virtual Machines (client & server) running on the same host. Specifically, the speed at which I can sequentially read a 1GB file on the client is much lower than what would be expected based on the measured network connection speed between the two VMs and the measured speed of reading the file directly on the server. The VMs are running Ubuntu 9.04 and the server is using the nfs-kernel-server package. According to various NFS tuning resources, changing the number of nfsd threads (in my case kernel threads) can affect performance. Usually this advice is framed in terms of increasing the number from the default of 8 on heavily-used servers. What I find in my current configuration: RPCNFSDCOUNT=8: (default): 13.5-30 seconds to cat a 1GB file on the client so 35-80MB/sec RPCNFSDCOUNT=16: 18s to cat the file 60MB/s RPCNFSDCOUNT=1: 8-9 seconds to cat the file (!!?!) 125MB/s RPCNFSDCOUNT=2: 87s to cat the file 12MB/s I should mention that the file I'm exporting is on a RevoDrive SSD mounted on the server using Xen's PCI-passthrough; on the server I can cat the file in under seconds ( 250MB/s). I am dropping caches on the client before each test. I don't really want to leave the server configured with just one thread as I'm guessing that won't work so well when there are multiple clients, but I might be misunderstanding how that works. I have repeated the tests a few times (changing the server config in between) and the results are fairly consistent. So my question is: why is the best performance with 1 thread? A few other things I have tried changing, to little or no effect: increasing the values of /proc/sys/net/ipv4/ipfrag_low_thresh and /proc/sys/net/ipv4/ipfrag_high_thresh to 512K, 1M from the default 192K,256K increasing the value of /proc/sys/net/core/rmem_default and /proc/sys/net/core/rmem_max to 1M from the default of 128K mounting with client options rsize=32768, wsize=32768 From the output of sar -d I understand that the actual read sizes going to the underlying device are rather small (<100 bytes) but this doesn't cause a problem when reading the file locally on the client. The RevoDrive actually exposes two "SATA" devices /dev/sda and /dev/sdb, then dmraid picks up a fakeRAID-0 striped across them which I have mounted to /mnt/ssd and then bind-mounted to /export/ssd. I've done local tests on my file using both locations and see the good performance mentioned above. If answers/comments ask for more details I will add them.

  Read the article

• rsync per-site configuration file?

  - by Scott

  I know how to configure a per-site entry for ssh, but is there any kind of a client configuration for rsync that allows per-site configuration options and aliases or similar shortcuts like the .ssh/config? I'm curious because I have a minimal ssh server installed on my android phone and I also have a minimal rsync tool on it as well. I'm getting tired of having to root login onto the phone and sym-link both tools to standard places the android OS looks for executables as the ssh server is bare bones and has a typical *bear multi-link binary for the basic unix commands (that does not include rsync) I end up having to include --rsync-path=/path/to/rsync/android/files/rsync every time I want to do any rsyncing of the files on my phone, but this path is always the same. I've gotten around it in the meantime with a glob approach in a shell script wrapper, but this sometimes limits the customization I can do with the rsync call. I'm just wondering if there is anything similar to the .ssh/config file where I can create an alias for my phone (e.g. 'android') where specifying rsync android:/mnt/sdcard will automatically assume --rsync-path=/blah/blah/blah --no-g --no-p --no-t etc. Tre`

  Read the article

• What is the best way to handle the multitude of different logs created all around the place?

  - by Low Kian Seong

  I run a few applications which creates their own logs. Then I run cron scripts on the same server to do importing of data for my app. When these cron errors out, the default is it sends emails to the user that runs the cron job. There are just too many places that I need to check the logs and mails for stuff that might have potentially went wrong. My question is, what is the best way to do this or even better is like a log parser application which will go through all the system logs when something really goes wrong instead of me having to go through it daily?

  Read the article

• mysql 5.1 - innodb - query_cache_size - 9,418,108 queries have been removed from the query cache due to lack of memory

  - by Tom C

  Currently running on a 16GB system - Ubuntu 64 bit. INnodb Buffer Pool is set to 10GB. tuning-primer shows the following: QUERY CACHE Query cache is enabled Current query_cache_size = 512 M Current query_cache_used = 501 M Current query_cache_limit = 4 M Current Query cache Memory fill ratio = 97.87 % Current query_cache_min_res_unit = 4 K However, 9418108 queries have been removed from the query cache due to lack of memory Perhaps you should raise query_cache_size That is over 9million queries removed. System uptime is 8 days. Should I remove the Query Cache altogether? Our db is always under heavy I/O. tia

  Read the article

• Ubunt doesn't mount one of my NTFS disks

  - by Jader Dias

  There is a mountable /dev/sda NTFS formatted (Windows disk) There is no /dev/sdb when I ls /dev (NTFS Data disk) There is a /dev/sdc which is another disk of the same model, (Ubuntu disk) I can see that Ubuntu detected this unmountable disk in the Disk Utility It states incorrectly it is unpartioned and a RAID volume. (it previously was RAID0 setup with /dev/sdc but now it is a simple volume, no RAID whatsoever) When I boot Windows 7, it uses this unmountable disk without a glitch The problem happens in both IDE and AHCI modes Ubuntu 10.04 Lucid Lynx

  Read the article

• is there a way to prevent network manager from storing the password for a wireless network

  - by tolomea

  Our corporate wireless network uses continuously changing passwords with RSA tokens. So every time we need to connect to the wireless we need to enter a new password off the RSA token. For extra fun using the wrong password a couple of times in a row causes the users account to be locked. Network manager automatically stores and reuses the password, with the net result that it is constant getting my account locked. Is there some way to prevent it from storing my password for that network? Or perhaps someway to get the gnome keyring to not store it?

  Read the article

• Input traffic shaping

  - by whitequark

  I know that I can shape output traffic with tc or a similar tool. However, I want to shape the input traffic now—actually, I want to prioritize downloading of files of certain type through a slow lossy connection. I know the reason tc can only shape output traffic: the host itself has no direct control over the amount of input traffic. On the other hand, TCP has some measures built in it which prevent the TCP traffic from overflowing a slow connection. So, can I mangle something in TCP header so that the remote host will think my connection is slower than it thinks? Suppose that I am able to set the corresponding mark on both types of connections with iptables. Is there any way to reduce the input bandwidth of connections of first type, but only if connections of second type are present?

  Read the article

• DNS caching server config problem

  - by Alex

  I have a Bind DNS caching-only server setup that is working. I am bringing up a new AD domain controller that will also be a DNS server for that AD but I don't want it responding to any DNS queries except those that are AD related. So, my goal is to leave this caching server as the primary DNS server for stations on the network and have it forward requests for the AD domain to the domain controller. My understanding is that I just need a forward zone for that domain pointing to the domain controller. However it does not seem to be working. So that leaves me to think that my caching server is not forwarding properly. For example, this AD is going to have a naming convention of hostname.mydomain.local. If I do an nslookup and specify the domain controller's IP address as the server, I can query addresses that exist in DNS on that server, such as dc1.mydomain.local. However, queries to my caching server times out (I get a response from the caching server if I query mydomain.local but none of the objects in that domain). Any suggestions? Here is my named.conf file: options { directory "/var/named"; listen-on { 192.168.0.14; 127.0.0.1; }; forwarders { ; ; }; forward first; }; zone "." in { type hint; file "db.cache"; }; zone "0.0.127.in-addr.arpa" in { type master; file "db.127.0.0"; }; //forward zone for mydomain.local zone "mydomain.local" { type forward; forwarders { 192.168.1.21; }; };

  Read the article

• Limited bandwidth and transfer rates per user.

  - by Cx03

  I searched for a while but couldn't find anything concrete, hopefully someone can help me. I'm going to be running a Debian server on a gigabit port, and want to give each user his/her fair share of internet access. The first objective is easy - transfer rates (speed) per user. From what I've looked at, IPTables/Shorewall could do the job easy. Is this easy to setup, or could one of you point me at a config? I was hoping to limit users at 300mbit or 650mbit each. The second objective gets complicated. Due to the usage of the boxes, most of the traffic will be internal network traffic that does NOT get counted to the quota. However, I still need to limit the external traffic, and if they go over, cut off access (or throttle traffic to a very low speed (10mbit?)). Let's say the user has a 3TB external traffic limit. The IF part is: If the hostname they are exchanging the traffic with DOES NOT MATCH .ovh. or .kimsufi. (company owns multiple TLDs), count to the quota. Once said quota exceeds 3TB, choke them. Where could I find a system to count that for me? It would also need to reset or be able to be manually reset on a monthly basis. Thanks ahead of time!

  Read the article

• Mint 13 does nothing when laptop lid is closed

  - by ewok

  I have a laptop running Mint 13. I have it hooked up to a 30" monitor and have no use for the laptop being open, so I put it on a shelf and close it. When I do that, the monitor goes blank. The power manager does not have an option for doing nothing when the lid is closed. The options are "Blank Screen", "Suspend", and "Shutdown". Is there a way to make the laptop not go to a blank screen when the lid is closed?

  Read the article

• Multiple user directories on EC2

  - by Joseph

  Im trying to set up multiple user directories on EC2 running Ubuntu, but im not sure how to set it up correctly so that i can serve files in the following format: http://<ec2 ip address>/user_1/public_html/file1.html and http://<ec2 ip address>/user_2/public_html/file3.html and so on for every user that i add. I tried looking for the httpd.conf file but i coulndt find it i only found apache2.conf Thank you guys.

  Read the article

• Problem installing CanonMF5880dn

  - by Paul

  Just got a CanonMF5880dn and cannot print to it from Suse 11.1 MacBook prints w/o issue ping 192.168.1.103 no problem cups sees it as Canon MF5880/MF5840 PCL at URI socket://192.168.1.103:9100 cups test print appears to submit and complete job but no action from printer Yast also seems to install printer correctly CQue2 also seems to install printer correctly all attempts to print yield same results: Suse indicates job processed correctly and completely but no printing happens. firewall is off http://192.168.1.103 in FF gives me the printer config menus correctly What have I failed to do?

  Read the article

• I can't write to a folder which I'm a member of

  - by user3265472

  I'm trying to setup folder access to a group so that all members of that group can create/edit/delete files within the folder. # create my group and add a member sudo addgroup dev sudo adduser martyn dev Now, logged in as "martyn", check my user has been added to "dev" group groups martyn martyn : martyn dev Now I want to change the group ownership of my project folder so all members of that group can edit it and files/folders within it. sudo chgrp -R dev myproject Just to check: martyn@localhost:/var/www$ ls -l total 4 drwxrwxr-x 3 dev dev 4096 May 31 15:53 myproject Now here's where it fails. I want to create a file within myproject (logged in as "martyn", a member of "dev"): vi myproject/test ..but when I try to save the file I get the following error: "myproject/test" E212: Can't open file for writing Why, as user "martyn" which is a member of "dev", can I not write this file? Even if I create the file so it exists, change the ownership to "dev" then try to edit and save - I get the same error.

  Read the article

• I'm trying to set up a LAMP server so it's totally anonymous, any suggestions?

  - by flexterra

  I'm going to set up a web service which will use the LAMP stack. One of the most important features of the site is that it should be anonymous. We thought that a cool thing will be if the server didn't made any logs that could potentially identify a user. I'm working on a web app for a news organization. They want a site to allow people to sumbit news leads and tips (text / files) to journalists. We think if we can provide good anonymity people will be more inclined to provide information. We will also teach how to use stuff like TOR as an extra precaution for whistleblowers Is this even possible? Any suggestions of obscure things we should look into?

  Read the article

• File permissions on web server

  - by plua

  I have just read this useful article on files permissions, and I am about to implement a as-strict-as-possible file permissions policy on our webserver. Our situation: we have a web server accessed through sftp by different users from within our company, and we have the general public accessing Apache - sometimes uploading files through PHP. I distinguish folders and files by their use. So based on this reading, here is my plan: All people who need to upload files will have separate users. But all of those users will belong to two groups: uploaders, and webserver. Apache will belong to the group webserver. Directories Permission: 771 Owner: user:uploaders Explanation: to access files in the folder, everybody needs to have execute permission. Only uploaders will be adding/removing files, so they also get r+w permission. Files within the web-root Permission: 664 Owner: user:uploaders Explanation: they will be uploaded and changed by different users, so both owner and group need to have w+r permissions. Webserver needs to only read files, so r permission only. Upload-directories Permission: 771 Owner: user:webserver Explanation: when files need to be uploaded, Apache needs to be able to write to this directory. But I figure it is safer to change the owner to webroot, thus giving Apache sufficient privileges (and all uploaders also belong to this group and will have the same permissions), while safeguarding from "others" writing to this folder. Uploaded files Permission: 664 Owner: user:webserver Explanation: after uploading Apache might need to delete files, but this is no problem because they have w+r permission of the folder. So no need to make this file any more accessible than r access for group. Being not an expert on file permissions, my question is whether or not this is the best possible policy for our situation? Any suggestions welcome.

  Read the article

• what to do when ctrl-c can't kill a process?

  - by Dustin Boswell

  Ctrl-c doesn't always work to kill the current process (for instance, if that process is busy in certain network operations). In that case, you just see "^C" by your cursor, and can't do much else. What's the easiest way to force that process to die now without losing my terminal? Summary of answers below: Usually, you can Ctrl-z to put the process to sleep, and then do "kill -9 process-pid", where you find the process's pid with 'ps' and other tools. On Bash (and possibly other shells) you can do "kill -9 %1" (or '%N' in general) which is easier. If Ctrl-z doesn't work, you'll have to open another terminal and kill from there.

  Read the article

< Previous Page | 541 542 543 544 545 546 547 548 549 550 551 552  | Next Page >