Search Results

Search found 22668 results on 907 pages for 'command prompt'.

Page 554/907 | < Previous Page | 550 551 552 553 554 555 556 557 558 559 560 561  | Next Page >

• shutdown.exe on Win Server2k3 64-bit cannot be found

  - by normalocity

  Server 2003 SP2 64-bit Verified my path settings are correct, as I can run other executables within the "system32" folder without issue. If I cd to "c:\windows\system32\" folder, and try to run "shutdown /?" I get "shutdown is not recognized as a valid..." you know - the message you get when you type a command that doesn't exist. Doing a "dir *.exe" inside the "system32" folder, also doesn't return "shutdown.exe" as one of the results. HOWEVER - if I go through Windows Explorer - there it is! I can see shutdown.exe. Also, if I go to "Start - Run" and type "shutdown /?", it works fine. So, works in the GUI, not on the command line. very strange. This is an excerpt of the last portion of "dir *.exe" when run on the "system32" folder. Note the lack of commonly used executables such as "shutdown.exe" and "tsadmin.exe" 02/18/2007 07:00 AM 24,064 route.exe 02/18/2007 07:00 AM 29,184 routemon.exe 02/18/2007 07:00 AM 14,848 rsh.exe 02/18/2007 07:00 AM 67,072 rsopprov.exe 02/18/2007 07:00 AM 77,824 rtcshare.exe 02/18/2007 07:00 AM 18,432 runas.exe 02/18/2007 07:00 AM 34,816 rundll32.exe 02/18/2007 07:00 AM 18,432 runonce.exe 02/18/2007 07:00 AM 13,312 savedump.exe 03/19/2009 07:51 PM 49,152 sc.exe 02/18/2007 07:00 AM 90,112 scardsvr.exe 02/18/2007 07:00 AM 152,064 schtasks.exe 02/18/2007 07:00 AM 16,384 schupgr.exe 02/18/2007 07:00 AM 31,232 sdbinst.exe 02/18/2007 07:00 AM 36,352 secedit.exe 02/18/2007 07:00 AM 32,768 sethc.exe 06/28/2006 12:12 AM 31,232 SetLACState.exe 02/18/2007 07:00 AM 41,472 setup.exe 02/18/2007 07:00 AM 25,088 setup16.exe 02/18/2007 07:00 AM 20,480 setupn.exe 02/18/2007 07:00 AM 60,416 setx.exe 02/18/2007 07:00 AM 10,752 sfc.exe 02/18/2007 07:00 AM 76,288 sfmprint.exe 02/18/2007 07:00 AM 11,776 sfmpsexe.exe 02/18/2007 07:00 AM 65,024 sfmsvc.exe 02/18/2007 07:00 AM 38,400 shmgrate.exe 02/18/2007 07:00 AM 71,168 sigverif.exe 02/18/2007 07:00 AM 26,112 skeys.exe 02/18/2007 07:00 AM 96,256 smlogsvc.exe 02/18/2007 07:00 AM 53,760 smss.exe 02/18/2007 07:00 AM 40,960 snmp.exe 02/18/2007 07:00 AM 25,088 sort.exe 02/18/2007 07:00 AM 9,728 sprestrt.exe 02/18/2007 07:00 AM 10,240 subst.exe 02/18/2007 07:00 AM 14,848 svchost.exe 02/18/2007 07:00 AM 54,272 syncapp.exe 02/18/2007 07:00 AM 18,896 sysedit.exe 02/18/2007 07:00 AM 29,696 syskey.exe 02/18/2007 07:00 AM 107,520 sysocmgr.exe 02/18/2007 07:00 AM 79,360 systeminfo.exe 02/18/2007 07:00 AM 3,072 systray.exe 02/18/2007 07:00 AM 58,880 takeown.exe 02/18/2007 07:00 AM 32,768 tapicfg.exe 02/18/2007 07:00 AM 84,480 taskkill.exe 02/18/2007 07:00 AM 87,552 tasklist.exe 02/18/2007 07:00 AM 168,960 taskmgr.exe 02/18/2007 07:00 AM 13,824 tcmsetup.exe 02/18/2007 07:00 AM 21,504 tcpsvcs.exe 02/18/2007 07:00 AM 28,672 timeout.exe 02/18/2007 07:00 AM 419,328 tracerpt.exe 02/18/2007 07:00 AM 12,800 tracert.exe 02/18/2007 07:00 AM 26,624 tsecimp.exe 02/18/2007 07:00 AM 37,376 typeperf.exe 10/24/2008 04:12 PM 64,000 tzchange.exe 02/18/2007 07:00 AM 5,632 unlodctr.exe 02/18/2007 07:00 AM 321,024 upg351db.exe 02/18/2007 07:00 AM 16,896 ups.exe 02/18/2007 07:00 AM 4,096 user.exe 02/18/2007 07:00 AM 26,112 userinit.exe 02/18/2007 07:00 AM 49,152 utilman.exe 02/18/2007 07:00 AM 47,104 uwdf.exe 02/18/2007 07:00 AM 29,184 verclsid.exe 02/18/2007 07:00 AM 112,640 verifier.exe 02/18/2007 07:00 AM 1,129 vwipxspx.exe 02/18/2007 07:00 AM 55,296 w32tm.exe 02/18/2007 07:00 AM 38,400 waitfor.exe 02/18/2007 07:00 AM 39,424 wdfmgr.exe 02/18/2007 07:00 AM 62,464 wextract.exe 02/18/2007 07:00 AM 38,400 where.exe 02/18/2007 07:00 AM 48,640 whoami.exe 02/18/2007 07:00 AM 36,864 winchat.exe 08/13/2007 06:45 PM 206,336 WinFXDocObj.exe 02/18/2007 07:00 AM 8,704 winhlp32.exe 02/18/2007 07:00 AM 12,800 winmsd.exe 02/18/2007 07:00 AM 2,112 winspool.exe 02/18/2007 07:00 AM 6,656 winver.exe 08/21/2002 05:13 AM 189,952 WISPTIS.EXE 02/18/2007 07:00 AM 67,072 wlbs.exe 02/18/2007 07:00 AM 10,560 wowexec.exe 02/18/2007 07:00 AM 10,752 wowreg32.exe 02/18/2007 07:00 AM 31,232 wpnpinst.exe 02/18/2007 07:00 AM 5,632 write.exe 02/18/2007 07:00 AM 114,688 wscript.exe 02/18/2007 07:00 AM 30,720 xcopy.exe

  Read the article

• Dual Monitor support rdp 7 to win 7 on esxi

  - by rphilli5

  I am trying to RDP from a Windows 7 Professional dual monitor physical machine to a Windows 7 Professional VM hosted on esxi 4.0. I can get the spanning option to work to both monitors, but I have tried 3 different methods of connecting but have not been able to use true multiple monitors. At different times, I tried checking the "use all monitors" option, command line mstsc /multimon and added the line use multimon:i:1 to the .rdp file. None of these worked. Any ideas? The physical machine can connect to other Windows 7 physical machines with true multi monitor access. I also have the same issue when going from a 32bit RC1 machine to a Windows 7 Professional x64, but not when going in the reverse direction. Here's the .rdp: screen mode id:i:2 use multimon:i:1 desktopwidth:i:1440 desktopheight:i:900 session bpp:i:16 winposstr:s:0,1,341,118,1139,568 compression:i:1 keyboardhook:i:2 audiocapturemode:i:0 videoplaybackmode:i:1 connection type:i:1 displayconnectionbar:i:1 disable wallpaper:i:1 allow font smoothing:i:0 allow desktop composition:i:0 disable full window drag:i:1 disable menu anims:i:1 disable themes:i:1 disable cursor setting:i:0 bitmapcachepersistenable:i:1 full address:s:192.168.1.5 audiomode:i:0 redirectprinters:i:1 redirectcomports:i:0 redirectsmartcards:i:1 redirectclipboard:i:1 redirectposdevices:i:0 redirectdirectx:i:1 autoreconnection enabled:i:1 authentication level:i:2 prompt for credentials:i:0 negotiate security layer:i:1 remoteapplicationmode:i:0 alternate shell:s: shell working directory:s: gatewayhostname:s: gatewayusagemethod:i:4 gatewaycredentialssource:i:4 gatewayprofileusagemethod:i:0 promptcredentialonce:i:1 use redirection server name:i:0 drivestoredirect:s:

  Read the article

• Windows 7 Black Screen On Boot, Seperate Bootable VHD Works Fine

  - by David Osborn

  I have a Window 7 x64 install with a bootable VHD (also Windows 7 x64). I was having problems getting my homeserver to do backups (VSS erred) so I ran check disk and used a tool from MS (cleanc2r.exe) to remove an empty Q drive from the VHD that I believe was a result of installing Office 2010 Beta. (All of this was done on the bootable VHD, not the main install.) Now I can't boot into the main install. It gets past the Starting Windows screen and then goes black. I can still boot into the bootable VHD and everything works fine from there. I have tried to boot the main install in Safe Mode/Safe Mode with Networking/and Safe Mode command prompt and it has the same issue. I ran chkdsk /r on the main install and after doing all the work there was a message about correcting some free space that was marked as allocated and also that it was unable to make an entry into the event log. I tried the startup repair utility and it found no problems. I don't see the setting for restore to last know good configuration so I couldn't do that. I don't recall installing anything new to the main install nor having hooked up any new hardware recently.

  Read the article

• Why does RoboCopy create a hidden system folder?

  - by Svish

  I thought I would try out RoboCopy for mirroring the contents of a folder to another harddrive. And seems like it worked. But, for some reason, to see the destination folder I have to both enable Show hidden files, folders and drives and disable Hide protected operating system files. Why is this? Both the source and destination folder was initially both visible and normal directories. When I open up the properties for that destination folder, the Hidden attribute is even disabled. What is going on here? Is it because I ran it in an administrator command prompt? Or is it an issue with my choice of modifiers? Or does robocopy really just work this way? robocopy E: I:\E /COPYALL /E /R:0 /MIR /B /ETA Update: Tried to copy another drive to another folder, and I got the same thing happening there. But when I try to just copy a folder to a different folder, then the destination folder stays normal. Could it be because I copy a drive? If so, how can I prevent this from happening? Cause I really do want to copy the whole drive...

  Read the article

• Are there any Microsoft Exchange Clients for iOS and Android that store their local data in an encrypted manner?

  - by Zac B

  I don't feel like this is a product recommendation question, more of a "does this tech even exist and is it feasible" question, but if I'm wrong, feel free to give this question the boot. Context: Our company has a bunch of traveling employees who access the company's Exchange server via thier iDevices or android phones, but because of the data protection laws in the state where our company is based (and the nature of the data our company works with), a recent security audit found that all mobile devices (laptops, phones, etc) operated by our company need to have all company correspondence and related data encrypted all the time. For laptops, that was easy: BitLocker or TrueCrypt, problem solved. For phones and tablets, however, I'm stumped. Sure, you can put lock screens/passwords on the phones, but the data is still accessible via external extraction, as law enforcement authorities already know. Question: Are there any clients for Microsoft Exchange that run on iOS or Android which store local data encrypted? The people using our mobile devices do a lot of their work while offline, so just giving them OWA access with SSL connection security isn't enough. Are there apps/technologies that present an additional login credential prompt to decrypt locally stored data in the app's storage area on the phone? My gut reaction when I started looking into this was "that doesn't sound like something Apple would allow into the App Store", but I've been wrong before...

  Read the article

• Server 2008 R2 DNS Lockup / Stops Resolving Internet Names

  - by Richard Maynard

  We've deployed our first 2008 R2 server on a client site which has replaced their existing 2003 DC. This server provides DNS resolution services to all client machines on that site for general internet usage. Since using the 2008 R2 DNS services we have noticed every couple of days the DNS server starts timing out when requests to certain sites are made (google is the only example I can provide at this time although it seems to be larger sites with problems rather than small - CDN compatiblity issue?). When you restart the DNS Server service then resolution returns to normal... just only for a day or so. Is anybody aware of any significant changes to the DNS server architecture or configuration out of the box in R2 that may explain this intermittent behaviour? I have already tried the fix listed here to no avail: http://weblogs.asp.net/owscott/archive/2009/09/15/windows-server-2008-r2-dns-issues.aspx The following PS command prompt info illustrates the issue: PS C:\Users\Administrator.UK> nslookup Default Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 > www.google.com Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 Non-authoritative answer: Name: www.l.google.com Addresses: 66.102.9.99 66.102.9.104 66.102.9.105 66.102.9.103 66.102.9.147 Aliases: www.google.com > www.google.co.uk Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 * s8209001.uk.kingdomfaith.com can't find www.google.co.uk: Server failed

  Read the article

• shutdown.exe on Win Server2k3 cannot be found

  - by normalocity

  Server 2003 SP2 64-bit Verified my path settings are correct, as I can run other executables within the "system32" folder without issue. If I cd to "c:\windows\system32\" folder, and try to run "shutdown /?" I get "shutdown is not recognized as a valid..." you know - the message you get when you type a command that doesn't exist. Doing a "dir *.exe" inside the "system32" folder, also doesn't return "shutdown.exe" as one of the results. HOWEVER - if I go through Windows Explorer - there it is! I can see shutdown.exe. Also, if I go to "Start - Run" and type "shutdown /?", it works fine. So, works in the GUI, not on the command line. very strange. This is an excerpt of the last portion of "dir *.exe" when run on the "system32" folder. Note the lack of commonly used executables such as "shutdown.exe" and "tsadmin.exe" 02/18/2007 07:00 AM 24,064 route.exe 02/18/2007 07:00 AM 29,184 routemon.exe 02/18/2007 07:00 AM 14,848 rsh.exe 02/18/2007 07:00 AM 67,072 rsopprov.exe 02/18/2007 07:00 AM 77,824 rtcshare.exe 02/18/2007 07:00 AM 18,432 runas.exe 02/18/2007 07:00 AM 34,816 rundll32.exe 02/18/2007 07:00 AM 18,432 runonce.exe 02/18/2007 07:00 AM 13,312 savedump.exe 03/19/2009 07:51 PM 49,152 sc.exe 02/18/2007 07:00 AM 90,112 scardsvr.exe 02/18/2007 07:00 AM 152,064 schtasks.exe 02/18/2007 07:00 AM 16,384 schupgr.exe 02/18/2007 07:00 AM 31,232 sdbinst.exe 02/18/2007 07:00 AM 36,352 secedit.exe 02/18/2007 07:00 AM 32,768 sethc.exe 06/28/2006 12:12 AM 31,232 SetLACState.exe 02/18/2007 07:00 AM 41,472 setup.exe 02/18/2007 07:00 AM 25,088 setup16.exe 02/18/2007 07:00 AM 20,480 setupn.exe 02/18/2007 07:00 AM 60,416 setx.exe 02/18/2007 07:00 AM 10,752 sfc.exe 02/18/2007 07:00 AM 76,288 sfmprint.exe 02/18/2007 07:00 AM 11,776 sfmpsexe.exe 02/18/2007 07:00 AM 65,024 sfmsvc.exe 02/18/2007 07:00 AM 38,400 shmgrate.exe 02/18/2007 07:00 AM 71,168 sigverif.exe 02/18/2007 07:00 AM 26,112 skeys.exe 02/18/2007 07:00 AM 96,256 smlogsvc.exe 02/18/2007 07:00 AM 53,760 smss.exe 02/18/2007 07:00 AM 40,960 snmp.exe 02/18/2007 07:00 AM 25,088 sort.exe 02/18/2007 07:00 AM 9,728 sprestrt.exe 02/18/2007 07:00 AM 10,240 subst.exe 02/18/2007 07:00 AM 14,848 svchost.exe 02/18/2007 07:00 AM 54,272 syncapp.exe 02/18/2007 07:00 AM 18,896 sysedit.exe 02/18/2007 07:00 AM 29,696 syskey.exe 02/18/2007 07:00 AM 107,520 sysocmgr.exe 02/18/2007 07:00 AM 79,360 systeminfo.exe 02/18/2007 07:00 AM 3,072 systray.exe 02/18/2007 07:00 AM 58,880 takeown.exe 02/18/2007 07:00 AM 32,768 tapicfg.exe 02/18/2007 07:00 AM 84,480 taskkill.exe 02/18/2007 07:00 AM 87,552 tasklist.exe 02/18/2007 07:00 AM 168,960 taskmgr.exe 02/18/2007 07:00 AM 13,824 tcmsetup.exe 02/18/2007 07:00 AM 21,504 tcpsvcs.exe 02/18/2007 07:00 AM 28,672 timeout.exe 02/18/2007 07:00 AM 419,328 tracerpt.exe 02/18/2007 07:00 AM 12,800 tracert.exe 02/18/2007 07:00 AM 26,624 tsecimp.exe 02/18/2007 07:00 AM 37,376 typeperf.exe 10/24/2008 04:12 PM 64,000 tzchange.exe 02/18/2007 07:00 AM 5,632 unlodctr.exe 02/18/2007 07:00 AM 321,024 upg351db.exe 02/18/2007 07:00 AM 16,896 ups.exe 02/18/2007 07:00 AM 4,096 user.exe 02/18/2007 07:00 AM 26,112 userinit.exe 02/18/2007 07:00 AM 49,152 utilman.exe 02/18/2007 07:00 AM 47,104 uwdf.exe 02/18/2007 07:00 AM 29,184 verclsid.exe 02/18/2007 07:00 AM 112,640 verifier.exe 02/18/2007 07:00 AM 1,129 vwipxspx.exe 02/18/2007 07:00 AM 55,296 w32tm.exe 02/18/2007 07:00 AM 38,400 waitfor.exe 02/18/2007 07:00 AM 39,424 wdfmgr.exe 02/18/2007 07:00 AM 62,464 wextract.exe 02/18/2007 07:00 AM 38,400 where.exe 02/18/2007 07:00 AM 48,640 whoami.exe 02/18/2007 07:00 AM 36,864 winchat.exe 08/13/2007 06:45 PM 206,336 WinFXDocObj.exe 02/18/2007 07:00 AM 8,704 winhlp32.exe 02/18/2007 07:00 AM 12,800 winmsd.exe 02/18/2007 07:00 AM 2,112 winspool.exe 02/18/2007 07:00 AM 6,656 winver.exe 08/21/2002 05:13 AM 189,952 WISPTIS.EXE 02/18/2007 07:00 AM 67,072 wlbs.exe 02/18/2007 07:00 AM 10,560 wowexec.exe 02/18/2007 07:00 AM 10,752 wowreg32.exe 02/18/2007 07:00 AM 31,232 wpnpinst.exe 02/18/2007 07:00 AM 5,632 write.exe 02/18/2007 07:00 AM 114,688 wscript.exe 02/18/2007 07:00 AM 30,720 xcopy.exe

  Read the article

• What causes Windows Media Player on Windows 8 to not play the entire library?

  - by somequixotic

  Behavior 1: Verify that the WMP playlist is clear of all songs. Turn on the "Shuffle" and "Repeat" features. Double-click on a music track in the Library. Click the "Next" button (double right angle brackets). A random song from any track in the Library is randomly chosen and played. When observing the Playlist (clicking the "Play" tab), the entire contents of the Library appears in the Playlist. Behavior 2: Verify that the WMP playlist is clear of all songs. Turn on the "Shuffle" and "Repeat" features. Double-click on a music track in the Library. Click the "Next" button (double right angle brackets). The button visually depresses like it has registered the click, but nothing happens. Absolutely nothing. Moreover, the "Previous" button is grayed out. When observing the Playlist, only the one song that was double-clicked appears in the Playlist. What causes Behavior 2? I cannot correlate any specific action I've taken with Behavior 2, and Behavior 1 has been the case as long as I can remember, all the way back to Windows XP. Even earlier during my usage of Windows 8, I recall Behavior 1 working correctly. But suddenly, inexplicably, without changing any settings in WMP, Behavior 2 kicked in, and persists after reboots. I've tried sfc /scannow in an administrator prompt. All system files are in order. I've downloaded all Windows Updates and driver updates. I've attempted to alter WMP options and playback settings to no avail. So... what is causing Behavior 2? Is this an intended, valid behavior, or is something malfunctioning? How would I know what that "something" is? How would I go about fixing it without just reinstalling Windows 8 fresh?

  Read the article

• Symantec Endpoint Protection Virus Definitions

  - by Gus Denton

  I have done some Googling but I cannot get a definitive answer certainly not from the Symantec KB. I have a Virtualised Win 2003R2 server 32bit. It has been provisioned to me with Symantec Endpoint Protection 11.0.62xxx CLIENT (not a definitions server) the directory C:\Program Files\Common Files\Symantec Shared\VirusDefs is 750MB IT doesn't contain .tmp directories so it is NOT a corrupt definitions server. IT does contain directories named with a date pattern YYYYMMDD.xxx Some of these folders are 12 months old and I would like to recover the space. The sysmantect forums are full of this stuff but a lot of the postings contain links back to documents that are not specific to End Point Protection Client. It appears that I should be able to delete the older folders and all will be OK. with a service restart however there is a warning about having Live Update Administrator Installed Firstly I have no idea if I have this installed how to I check and secondly can I just ditch these old files and restart ? Regards Gus Denton Learning and Teaching Uni of New South Wales Sydney Australia For those trying to assist me I thankyou. I have followed some instructions found on the Symantec site and assumed that the response from Nixphoe would resolve my issue. It appears that as I am on a provisioned VM from a central IT unit I cannot run the Symantec commands from the Run prompt as my admin creds to get me in. (smc -stop) Basically I need to claw back some Diskspace from the c: drive which is being filed up with WSUS patches and Symantec files. I have managed to delete one symantec cache through the live update control panel and recovered 470Mb I suppose my last question for those more experienced than myself is, can I simply remove say the two oldest virus definition folders without completely foobaring the End Point protection and the server ? Regards Gus

  Read the article

• Scheduled task does not run on WIndows 2003 server on VMWare unattened, runs fine otherwise

  - by lnm

  Scheduled task does not run on Windows 2003 server on VMWare. The same setup runs fine on standalone server. Test below explains the problem. We really need to run a more complex bat file, but this shows the issue. I have a bat file that copies a file from server A to server B. I use full path name, no drive mapping. Runs fine on server B from command prompt. I created a task that runs this bat file under a domain id with password that is part of administrator group on both servers. Task runs fine from Scheduled task screen, and as a scheduled task as long as somebody is logged into the server. If nobody is logged in, the task does not run. There is no error message in Task Scheduler log, just an entry that the task started, bit no entry for finish or an error code. To add insult to injury, if the task copies a file in the opposite direction, from server B to server A, it runs fine as a scheduled unattended task. If I copy a file from server B to server B, the task also runs fine unattended, I recreated exactly the same setup on a standalone server. No issues at all. I checked obvious things like the task has "run only as logged in" unchecked, domain id has run as a batch job privilege and logon rights, Task Scheduler service runs as a local system, automatic start. Any suggestions?

  Read the article

• OpenSSL response 404 issue on centOS 6

  - by dsp_099

  I followed this tutorial (though it's for 5.2, I figured I'd be alright). The changes I had to make that seemed to have worked: Rename ca.csr to ca.cslr (that's the one the command generated) List it in the ssl.conf as ca.cslr instead of ca.csr I have the following in the httpd.conf <VirtualHost *:80> DocumentRoot /etc/test ServerName site.com </VirtualHost> <VirtualHost *:433> SSLEngine on SSLCertificateFile /etc/pki/tls/certs/ca.crt SSLCertificateKeyFile /etc/pki/tls/private/ca.key <Directory /etc/test> AllowOverride All </Directory> DocumentRoot /etc/test ServerName cryptokings.com </VirtualHost> /test contains a folder inside of it, accessible via http://site.com/test/foo, however attempting to access it via https://site.com/test/foo results in warning that the certificate is untrusted (self-signed, no biggie) a 404 error. Chrome's complains about the certificate are the following: The identity of this website has not been verified. • Server's certificate does not match the URL. • Server's certificate is not trusted. I think those warnings are a side-effect of a self-signed certificate - or is the first one something that needs to be addressed? I seem to be able fetch the root page via https just fine though, it shows a standard CentOS setup page. (That said, I haven't added a VirtualHost entry for it so I suppose that makes sense) I think I've made a mistake somewhere during the setup as I'm not too familiar with the process. During setup, I was prompted for a type of password that would be required when apache restarts but running service httpd restart does not seem to prompt me for one. Any help would be appreciated.

  Read the article

• Openswan ipsec transport tunnel not going up

  - by gparent

  On ClusterA and B I have installed the "openswan" package on Debian Squeeze. ClusterA ip is 172.16.0.107, B is 172.16.0.108 When they ping one another, it does not reach the destination. /etc/ipsec.conf: version 2.0 # conforms to second version of ipsec.conf specification config setup protostack=netkey oe=off conn L2TP-PSK-CLUSTER type=transport left=172.16.0.107 right=172.16.0.108 auto=start ike=aes128-sha1-modp2048 authby=secret compress=yes /etc/ipsec.secrets: 172.16.0.107 172.16.0.108 : PSK "L2TPKEY" 172.16.0.108 172.16.0.107 : PSK "L2TPKEY" Here is the result of ipsec verify on both machines: root@cluster2:~# ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.28/K2.6.32-5-amd64 (netkey) Checking for IPsec support in kernel [OK] NETKEY detected, testing for disabled ICMP send_redirects [OK] NETKEY detected, testing for disabled ICMP accept_redirects [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [FAILED] Checking for 'ip' command [OK] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] root@cluster2:~# This is the end of the output of ipsec auto --status: 000 "cluster": 172.16.0.108<172.16.0.108>[+S=C]...172.16.0.107<172.16.0.107>[+S=C]; prospective erouted; eroute owner: #0 000 "cluster": myip=unset; hisip=unset; 000 "cluster": ike_life: 3600s; ipsec_life: 28800s; rekey_margin: 540s; rekey_fuzz: 100%; keyingtries: 0 000 "cluster": policy: PSK+ENCRYPT+COMPRESS+PFS+UP+IKEv2ALLOW+lKOD+rKOD; prio: 32,32; interface: eth0; 000 "cluster": newest ISAKMP SA: #1; newest IPsec SA: #0; 000 "cluster": IKE algorithm newest: AES_CBC_128-SHA1-MODP2048 000 000 #3: "cluster":500 STATE_QUICK_R0 (expecting QI1); EVENT_CRYPTO_FAILED in 298s; lastdpd=-1s(seq in:0 out:0); idle; import:admin initiate 000 #2: "cluster":500 STATE_QUICK_I1 (sent QI1, expecting QR1); EVENT_RETRANSMIT in 13s; lastdpd=-1s(seq in:0 out:0); idle; import:admin initiate 000 #1: "cluster":500 STATE_MAIN_I4 (ISAKMP SA established); EVENT_SA_REPLACE in 2991s; newest ISAKMP; lastdpd=-1s(seq in:0 out:0); idle; import:admin initiate 000 Interestingly enough, if I do ike-scan on the server here's what happens: Doesn't seem to take my ike settings into account root@cluster1:~# ike-scan -M 172.16.0.108 Starting ike-scan 1.9 with 1 hosts (http://www.nta-monitor.com/tools/ike-scan/) 172.16.0.108 Main Mode Handshake returned HDR=(CKY-R=641bffa66ba717b6) SA=(Enc=3DES Hash=SHA1 Auth=PSK Group=2:modp1024 LifeType=Seconds LifeDuration(4)=0x00007080) VID=4f45517b4f7f6e657a7b4351 VID=afcad71368a1f1c96b8696fc77570100 (Dead Peer Detection v1.0) Ending ike-scan 1.9: 1 hosts scanned in 0.008 seconds (118.19 hosts/sec). 1 returned handshake; 0 returned notify root@cluster1:~# I can't tell what's going on here, this is pretty much the simplest config I can have according to the examples.

  Read the article

• Dual booting Linux/Win7, Grub refuses to load Win7

  - by JohnB

  Decided to give Linux Mint a try (Ubuntu's interface annoys me), so I installed it with the intention of dual booting with Windows 7. Installation went fine, but now I can only boot into Linux Mint. Grub lists two Windows 7 menu options, but selecting either of them causes an "unknown file system" error and dumps me into a Grub recovery prompt. There, I have to manually reset the root and prefix options, as they reset hd0,msdos6 when they should be hd0,msdos5. I ran Boot Repair twice, once to fix grub errors, once to rebuild the MBR, but it didn't fix anything. Here is the log: http://paste.ubuntu.com/1029675/ fdisk output: Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 1486249145 743021149 7 HPFS/NTFS/exFAT /dev/sda3 1486249982 1953523711 233636865 5 Extended /dev/sda5 1486249984 1945141247 229445632 83 Linux /dev/sda6 1945143296 1953523711 4190208 82 Linux swap / Solaris grub.cfg: ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sda1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 86184D18184D091F chainloader +1 } menuentry "Windows 7 (loader) (on /dev/sda2)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root 56D84F84D84F60FB chainloader +1 } ### END /etc/grub.d/30_os-prober ### I have found a few similar troubleshooting guides so far, but so far no amount of updating/configuring Grub has been successful. Last resort is, I suppose, use the W7 recovery disc and start over. Thanks in advance! Linux Mint 13 Maya, 64-bit Windows 7 Home Edition, 64-bit

  Read the article

• How to install a private user script in Chrome 21+?

  - by Mathias Bynens

  In Chrome 20 and older versions, you could simply open any .user.js file in Chrome and it would prompt you to install the user script. However, in Chrome 21 and up, it downloads the file instead, and displays a warning at the top saying “Extensions, apps, and user scripts can only be added from the Chrome Web Store”. The “Learn More” link points to http://support.google.com/chrome_webstore/bin/answer.py?hl=en&answer=2664769, but that page doesn’t say anything about user scripts, only about extensions in .crx format, apps, and themes. This part sounded interesting: Enterprise Administrators: You can specify URLs that are allowed to install extensions, apps, and themes directly through the ExtensionInstallSources policy. So, I ran the following commands, then restarted Chrome and Chrome Canary: defaults write com.google.Chrome ExtensionInstallSources -array "https://gist.github.com/*" defaults write com.google.Chrome.canary ExtensionInstallSources -array "https://gist.github.com/*" Sadly, these settings only seem to affect extensions, apps, and themes (as it says in the text), not user scripts. (I’ve filed a bug asking to make this setting affect user scripts as well.) Any ideas on how to install a private user script (that I don’t want to add to the Chrome Web Store) in Chrome 21+? Update: The problem was that gist.github.com’s raw URLs redirect to a different domain. So, use these commands instead: # Allow installing user scripts via GitHub or Userscripts.org defaults write com.google.Chrome ExtensionInstallSources -array "https://*.github.com/*" "http://userscripts.org/*" defaults write com.google.Chrome.canary ExtensionInstallSources -array "https://*.github.com/*" "http://userscripts.org/*" This works!

  Read the article

• Possible DNS issue?

  - by durilai

  I am having an issue, which I think stems from DNS. I have 2 servers. Server 1 is AD server with DNS, which was automatically configured when installing AD. The second server is a web server that is part of the domain, but it is not AD nor any other role. I can remote desktop in from server 1 using internal IP address, but when I attempt to connect from any other computer it fails, the computer can connect to server 1. I am able to ping both servers, as well as nslookup both using their FQDN. I am also able to telnet to port 3389. Any help is appreciated UPDATE I do not think it is DNS anymore, but not sure what it is. The remote desktop connects and I get to the login prompt, but when I start to enter credentials it disconnects. I then am unable to reconnect. If I wait for about 10 minutes it will allow me to repeat, but with the same results. UGH!!!

  Read the article

• Safe mode boot with no change on screen but ongoing hard disk activity - why?

  - by omatai

  I have a machine with a dying hard drive - bad sectors are starting to multiply :-( The first sign (24 hours ago) was that it had an unmountable boot volume. At this time, I tried booting to safe mode with command prompt, which worked, after which I rebooted normally and ran a chkdsk. It has since been working as well as I could expect, but slowly getting less reliable. So I scheduled another chkdsk on both partitions (C: - boot, D: - data), having freed up a lot of space on both partitions to give Windows a little more scope for repairs (hopefully?). I then rebooted. On reboot, it protested about the unmountable boot volume again, so I booted to safe mode. I got the same list of drivers loaded as yesterday, and then no change to the screen for the past 2 hours. However, I see a flickering hard drive indicator light - not always on, but seldom ever off. What is happening? Is the chkdsk that runs in safe mode one which produces nothing on the screen and so chkdsk could be doing its thing... or is Windows still trying (but failing) to boot into Safe Mode?

  Read the article

• How to wake from screensaver directly to the login screen in Ubuntu

  - by torbengb

  (a.k.a. How to switch users without entering password, part II) (see part I) I've got Ubuntu 9.10 with a user account for my wife, and one for myself. "Wake-from-screensaver" should result in "choose user" without having to enter any password. I know how to do that in Windows, but I'm not good with Linux (yet). Part of this was answered in my earlier question which helped me get past the login screen without passwords (after booting, and after choosing "switch user"), but once the screensaver kicks in and I wake it up again, the system does not present the "choose user" screen. Instead, it either turns off the screensaver and presents the desktop of the most recent user, or (if the screensaver is set to lock the screen) prompt for the user's password (which can be handily surpassed by clicking the "switch user" button and choosing the same user again). So, the login ("choose user") screen has been dealt with. How do I make the (any) screensaver return to the login screen at wake, rather than to the current user's desktop? Windows can do this, I'm sure Linux can too - but how?

  Read the article

• Crash in audio resampler with some audio rates - FFMPEG PHP ( Solved! )

  - by Olaf Erlandsen

  i have a problem with this command( FFMPEG PHP ): Command: ffmpeg -i 62f76f050494f0ed6a5997967c00c0c0.wmv -ss 0 -t 99 -y -ar 44100 -async 44100 -r 29.970 -ac 2 -qscale 5 -f flv 62f76f050494f0ed6a5997967c00c0c0.flv Output: FFmpeg version 0.6.5, Copyright (c) 2000-2010 the FFmpeg developers built on Jan 29 2012 17:52:15 with gcc 4.4.5 20110214 (Red Hat 4.4.5-6) configuration: --prefix=/usr --libdir=/usr/lib64 --shlibdir=/usr/lib64 --mandir=/usr/share/man --incdir=/usr/include --disable-avisynth --extra-cflags='-O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic -fPIC' --enable-avfilter --enable-avfilter-lavf --enable-libdc1394 --enable-libdirac --enable-libfaac --enable-libfaad --enable-libfaadbin --enable-libgsm --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libx264 --enable-gpl --enable-nonfree --enable-postproc --enable-pthreads --enable-shared --enable-swscale --enable-vdpau --enable-version3 --enable-x11grab libavutil 50.15. 1 / 50.15. 1 libavcodec 52.72. 2 / 52.72. 2 libavformat 52.64. 2 / 52.64. 2 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.19. 0 / 1.19. 0 libswscale 0.11. 0 / 0.11. 0 libpostproc 51. 2. 0 / 51. 2. 0 [asf @ 0xe81670]max_analyze_duration reached Input #0, asf, from '/var/www/resources/tmp/62f76f050494f0ed6a5997967c00c0c0.wmv': Metadata: WMFSDKVersion : 12.0.7601.17514 WMFSDKNeeded : 0.0.0.0000 IsVBR : 0 Duration: 00:00:50.87, bitrate: 2467 kb/s Stream #0.0: Audio: wmapro, 44100 Hz, stereo, flt, 256 kb/s Stream #0.1: Video: vc1, yuv420p, 950x460 [PAR 1:1 DAR 95:46], 25 fps, 25 tbr, 1k tbn, 25 tbc Output #0, flv, to '/var/www/resources/media/62f76f050494f0ed6a5997967c00c0c0.flv': Metadata: encoder : Lavf52.64.2 Stream #0.0: Video: flv, yuv420p, 950x460 [PAR 1:1 DAR 95:46], q=2-31, 200 kb/s, 1k tbn, 29.97 tbc Stream #0.1: Audio: libmp3lame, 11025 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.1 -> #0.0 Stream #0.0 -> #0.1 Press [q] to stop encoding frame= 72 fps= 0 q=5.0 size= 0kB time=10.91 bitrate= 0.0kbits/s Multiple frames in a packet from stream 0 Warning, using s16 intermediate sample format for resampling frame= 141 fps=139 q=5.0 size= 103kB time=8.15 bitrate= 103.2kbits/s frame= 220 fps=144 q=5.0 size= 875kB time=10.92 bitrate= 656.6kbits/s frame= 290 fps=143 q=5.0 size= 1525kB time=13.74 bitrate= 909.1kbits/s frame= 356 fps=141 q=5.0 size= 2153kB time=15.99 bitrate=1103.1kbits/s frame= 427 fps=141 q=5.0 size= 2847kB time=18.70 bitrate=1247.0kbits/s frame= 497 fps=141 q=5.0 size= 3771kB time=21.16 bitrate=1460.0kbits/s frame= 575 fps=142 q=5.0 size= 4695kB time=24.61 bitrate=1563.0kbits/s frame= 639 fps=141 q=5.0 size= 5301kB time=26.80 bitrate=1620.2kbits/s frame= 703 fps=139 q=5.0 size= 5829kB time=29.36 bitrate=1626.2kbits/s frame= 774 fps=139 q=5.0 size= 6659kB time=32.39 bitrate=1684.0kbits/s frame= 842 fps=139 q=5.0 size= 7915kB time=35.27 bitrate=1838.6kbits/s frame= 911 fps=139 q=5.0 size= 9011kB time=37.98 bitrate=1943.4kbits/s frame= 975 fps=138 q=5.0 size= 9788kB time=40.59 bitrate=1975.3kbits/s frame= 1041 fps=138 q=5.0 size= 10904kB time=43.83 bitrate=2037.9kbits/s frame= 1115 fps=138 q=5.0 size= 11795kB time=46.24 bitrate=2089.8kbits/s frame= 1183 fps=138 q=5.0 size= 12678kB time=48.74 bitrate=2130.7kbits/s frame= 1247 fps=137 q=5.0 size= 13964kB time=51.36 bitrate=2227.5kbits/s frame= 1271 fps=136 q=5.0 Lsize= 15865kB time=58.86 bitrate=2208.1kbits/s video:15366kB audio:462kB global headers:0kB muxing overhead 0.238956% Problem: Warning, using s16 intermediate sample format for resampling I've also tried changing the parameter From -ar 44100 to -ar 11025 Thanks! Solution: Read this link: http://en.wikipedia.org/wiki/MP3#Bit_rate

  Read the article

• Elevating UAC via .bat file?

  - by jslaker

  Pretty straightforward one that I'm having trouble finding an answer to. serverfault previously helped me with finding a way to automate Windows updates without using WSUS. It's working fantastically, but to run it over the network, you have to first mount a shared drive. That's pretty simple XP since you just mount the drive and run the updater. On Vista and W7, though, this all has to be done with elevated privileges to work correctly. The UAC account can't see network drives mounted by the regular user, so in order to get everything working, I have to mount the share via net use from an escalated shell. I'd like to automate mounting this share and launching the updater via a simple .bat file. I could probably just instruct everybody to right click "Run as Administrator" on the .bat file, but I'd like to keep things as simple as possible and have the .bat automatically prompt the user to escalate their privileges. Since these computers don't belong to us, I can't count on anything like Powershell being installed, so that rules any solution along those lines out and pretty much have to rely on things that would be included in an RTM Vista install. I'm hoping I'm mostly missing something obvious here. :)

  Read the article

• DNS lookups failing somewhere between firewall and router

  - by TessellatingHeckler

  we have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch == Intel load balanced NICS in a server. It has been fine for years, suddenly DNS resolution stopped working on the server. No changes that I know of, so I can't work backwards from there. It was configured with the ISP's DNS servers, neither network device does DNS relaying. Wireshark shows the request go out but nothing comes back. The server networking stack seems OK though, because if we query an internal DNS server on a remote site, that works. I can logon to the Cisco, and DNS resolves OK from the command line. I can logon to the ZyWall, and DNS does not resolve from the command line. So the problem seems to be the firewall, patch cable or router, yes? On the router: interface Ethernet0 ip address aaa.bbb.ccc.ddd 255.255.255.ddd ip tcp adjust-mss 1450 hold-queue 100 out On the firewall: DNS server set to 8.8.8.8 (Google's), DNS traffic allowed LAN-WAN. What else should I look for? Update: Following This guide I've got traffic logging on the Cisco. I have also got access to a public DNS server which I can run tcpdump on to see things from the other side. And as per the below comments, I've tested with Dig and see that DNS over TCP works, and over UDP does not. Currently: DNS request from the server using TCP shows up in the firewall log, and in the Cisco log, and in tcpdump on the DNS server, the answer comes back, it works fine. DNS request from the server using UDP shows up in the firewall log, and in the Cisco log, does NOT show in tcpdump on the DNS server, times out. DNS request from the cisco (using UDP) does show up in tcpdump on the DNS server, answer received, works fine. Ping requests from the server and the cisco to the DNS server show up in tcpdump on the DNS server. DNS request from the server using UDP does show up on the firewall. Summary: TCP seems fine throughought. UDP works over the ADSL and to the Cisco, and it works from the server to the Cisco, but it doesn't cross the Cisco properly, it seems. I did see the Cisco showing as connected at 10Mb/full-duplex internally, and the firewall showing as 100Mb/full-duplex externally. I have forced the firewall to 10Mb and rebooted both devices. That seemed to help get UDP traffic (server-firewall-cisco) instead of (server-firewall), but did not fix it. Update: Sanitized Cisco config: version 12.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname cisco ! logging queue-limit 100 enable secret 5 {password} enable password 7 {password} ! ip subnet-zero ip domain name example.org ip name-server {nameserver_IP} ! ! ip audit notify log ip audit po max-events 100 no ftp-server write-enable ! interface Ethernet0 ip address {Inside_public_IP} 255.255.255.248 ip tcp adjust-mss 1460 hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface Dialer1 ip unnumbered Ethernet0 encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer persistent no cdp enable ppp chap hostname {ADSL_Username} ppp chap password 7 {ADSL_Password} ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 no ip http server no ip http secure-server ! access-list 23 permit {IP} dialer-list 1 protocol ip permit no cdp run snmp-server enable traps tty ! {con, vty} end

  Read the article

• DIR $file "File Not Found" vs DIR $filedir shows it....not permissions, not USB

  - by Kev

  I was having this problem before on a USB drive, but now it's happening on my main RAID5-backed hard disk: 2013-10-17 9:37 C:\>dir "C:\Shares\Shared\Reference\Safety Management System\Vid eo CD\AutoPlay\Docs\Manuel*" Volume in drive C has no label. Volume Serial Number is 3C18-E114 Directory of C:\Shares\Shared\Reference\Safety Management System\Video CD\AutoP lay\Docs 2003-09-09 11:29 PM 1,056,768 Manuel d'intervention d'urgence MFC.doc 2004-06-20 10:36 PM 139,849 Manuel d'intervention d'urgence MFC.pdf 2 File(s) 1,196,617 bytes 0 Dir(s) 196,068,691,968 bytes free 2013-10-17 9:38 C:\>dir "C:\Shares\Shared\Reference\Safety Management System\Vid eo CD\AutoPlay\Docs\Manuel d'intervention d'urgence MFC.doc" Volume in drive C has no label. Volume Serial Number is 3C18-E114 Directory of C:\Shares\Shared\Reference\Safety Management System\Video CD\AutoP lay\Docs File Not Found 2013-10-17 9:38 C:\> This is from a Command Prompt window where I went to Properties and told it I wanted to modify who it ran as. I opened it, had it run as me with the "restricted access" unchecked, then ran the above. The file in question has the following ACLs: Administrators, SYSTEM, and OurCompanyUsers. All three have full control of everything. Nobody has any Deny bits set. I am a member of Administrators. So I don't believe it's a permissions issue. It's not a USB drive, so this time there is no question of USB hardware. Windows Server 2003 Standard Edition SP2. What does this mean? Is this more likely a hardware or software problem?

  Read the article

• RemoteApp .rdp embed creds?

  - by Chris_K

  Windows 2008 R2 server running Remote Desktop Services (what we used to call Terminal Services back in the olden days). This server is the entry point into a hosted application -- you could call it Software as a Service I suppose. We have 3rd party clients connecting to use it. Using RemoteApp Manager to build RemoteApp .rdp shortcuts to distribute to client workstations. These workstations are not in the same domain as the RDS server. There is no trust relationship between domains (nor will there be). There is a tightly controlled site to site VPN between workstations and the RDS server, we're quite confident we have access to the server locked down. The remoteApp being run is an ERP application with its own authentication scheme. The issue? I'm trying to avoid the need to create AD logins for every end user when connecting to the RemoteApp server. In fact, since we're doing a remoteApp and they have to authenticate to that app, I'd rather just not prompt them at all for AD creds. I certainly don't want them caught up in managing AD passwords (and periodic expirations) for accounts they only use to get to their ERP login. However, I can't figure out how to embed AD creds in a RemoteApp .rdp file. I don't really want to turn off all authentication on the RDS server at that level. Any good options? My goal is to make this as seamless as possible for the end-users. Clarifying questions are welcome.

  Read the article

• Windows XP mounting USB drive to same letter as previously mapped network drive

  - by GAThrawn

  Why does Windows always mount a USB drive as the next drive letter after the last physical drive, even when that letter is already taken by a mapped drive, and is there any way to improve this behaviour? What happens is I tend to use a few different flash drives on my PC, as well as having both a Blackberry and a personal phone that mount as USB drives when I plug them in to charge. Being on a corporate PC I also have a number of mapped network drives (some set by login script, some set as persistent mappings in my profile). When I first login I'll have drive letters like this: C: - Local Drive D: - DVD Drive G: - Login script mapped drive J: - Login script mapped drive When I plug the Blackberry in it'll mount two drives (one for onboard storage, one for the SD card) as E: and F:. If I then plug in another USB drive it will mount as G:, even though that's already taken by a network mapped drive. This leaves me with the following drives: C: - Local Drive D: - DVD Drive E: - USB drive (Blackberry) F: - USB drive (Blackberry) G: - Login script mapped drive [G: - USB drive - mounted but not visible in Explorer or command prompt] J: - Login script mapped drive I then have to go into Disk Management, find the new USB drive that's mounted to G: and re-assign it to another letter eg Z:, once this is done Auto-Play detects it and throws up its normal dialog, and its browseable in Explorer. While this is OK to do if you only use one or two USB drives and have admin access to your PC with your login account, its a total pain in the proverbial if you regularly use a whole load of different USB devices, and corporate policy means you have one account for your normal login (that only has User access to workstations), but have to use a different account for any privileged action. I realize that one possible reason for this is the difference between hardware which is mounted and assigned drive letters at the systen level, and mapped drives which are done at the user level. For USB devices that are already plugged in before login, then obviously they're mounted before Windows knows what network drives may be mapped. However if you plug the USB devices in after you're fully logged in and have drives mapped then Windows must know which letters are available?

  Read the article

• duplicity fail: not promping for password: "Running 'sftp user@host' failed"

  - by Thr4wn

  I have two linode VPS accounts and I want to back up one onto the other (the reasons are mainly for fun and to practice server administration.) the short version Duplicity isn't even asking for my password, but immediately says "invalid SSH password" (but I can ssh into the other server). why? the long version When I run duplicity /home/me scp://[email protected]//root/backup I get Invalid SSH password Running 'sftp [email protected]' failed (attempt #1) Invalid SSH password Running 'sftp [email protected]' failed (attempt #2) Invalid SSH password Running 'sftp [email protected]' failed (attempt #3) And it says Invalid SSH password immediately with no opportunity for me to actually type the password. When I type duplicity full -v9 --num-retries 4 /home/me scp://[email protected]//root/backup I get Main action: full Running 'sftp [email protected]' (attempt #1) State = sftp, Before = 'Connecting to 97.107.129.67... [email protected]'s' State = sftp, Before = '' Invalid SSH password Running 'sftp [email protected]' failed (attempt #1) I can ssh into [email protected] fine, and in fact have the ip in known_hosts before I tried any of this. serer 1 (from which I'm running the duplicity command) is Linode's default Ubuntu 8 setup with only a handful of programs installed via apt-get. server 2 (represented by x.x.x.x) is literally only Linode's default Ubuntu 8 setup I previously tried using SystemImager -- would that have changed settings in a destructive way? (I have removed and rebooted since then) Isn't Duplicity supposed to prompt for password? Am I using it wrong? are there common mistakes/dependencies I need to know about? Is there any way that x.x.x.x could be setup that could make this not work (I used Linode's default Ubuntu 8 setup and barely )?

  Read the article

• How to prevent delays associated with IPv6 AAAA records?

  - by Nic

  Our Windows servers are registering IPv6 AAAA records with our Windows DNS servers. However, we don't have IPv6 routing enabled on our network, so this frequently causes stall behaviours. Microsoft RDP is the worst offender. When connecting to a server that has a AAAA record in DNS, the remote desktop client will try IPv6 first, and won't fall back to IPv4 until the connection times out. Power users can work around this by connecting to the IP address directly. Resolving the IPv4 address with ping -4 hostname.foo always works instantly. What can I do to avoid this delay? Disable IPv6 on client? Nope, Microsoft says IPv6 is a mandatory part of the Windows operating system. Too many clients to ensure this is set everywhere consistently. Will cause more problems later when we finally implement IPv6. Disable IPv6 on the server? Nope, Microsoft says IPv6 is a mandatory part of the Windows operating system. Requires an inconvenient registry hack to disable the entire IPv6 stack. Ensuring this is correctly set on all servers is inconvenient. Will cause more problems later when we finally implement IPv6. Mask IPv6 records on the user-facnig DNS recursor? Nope, we're using NLNet Unbound and it doesn't support that. Prevent registration of IPv6 AAAA records on the Microsoft DNS server? I don't think that's even possible. At this point, I'm considering writing a script that purges all AAAA records from our DNS zones. Please, help me find a better way. UPDATE: DNS resolution is not the problem. As @joeqwerty points out in his answer, the DNS records are returned instantly. Both A and AAAA records are immediately available. The problem is that some clients (mstsc.exe) will preferentially attempt a connection over IPv6, and take a while to fall back to IPv4. This seems like a routing problem. The ping command produces a "General failure" error message because the destination address is unroutable. C:\Windows\system32>ping myhost.mydomain Pinging myhost.mydomain [2002:1234:1234::1234:1234] with 32 bytes of data: General failure. General failure. General failure. General failure. Ping statistics for 2002:1234:1234::1234:1234: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), I can't get a packet capture of this behaviour. Running this (failing) ping command does not produce any packets in Microsoft Network Monitor. Similarly, attempting a connection with mstsc.exe to a host with an AAAA record produces no traffic until it does a fallback to IPv4. UPDATE: Our hosts are all using publicly-routable IPv4 addresses. I think this problem might come down to a broken 6to4 configuration. 6to4 behaves differently on hosts with public IP addresses vs RFC1918 addresses. UPDATE: There is definitely something fishy with 6to4 on my network. When I disable 6to4 on the Windows client, connections resolve instantly. netsh int ipv6 6to4 set state disabled But as @joeqwerty says, this only masks the problem. I'm still trying to find out why IPv6 communication on our network is completely non-working.

  Read the article

< Previous Page | 550 551 552 553 554 555 556 557 558 559 560 561  | Next Page >