Search Results

Search found 18209 results on 729 pages for 'loop device'.

Page 578/729 | < Previous Page | 574 575 576 577 578 579 580 581 582 583 584 585  | Next Page >

  • Single computer on network cannot connect to internet.

    - by user34630
    Hi All, I hope you can help me out! :) I have 3 computers and one device (Xbox) on my home network; 2 running XP and one on Vista. The computer that can't connect to the internet (XP) is old and failing, and shows no warning before it completely runs out of battery. Thus today, I started it up forgetting that I had unplugged it the night before, and it just ran out of battery entirely whilst I was using it and died. I think that before this I had been browsing the internet, but I can't remember for certain. (i.e. The problem I am having may or may not have been caused by this 'hard' power off). Anyway, now when I start the computer up it takes 5-10 minutes after logging on to display the start bar and icons. Also, I cannot browse the internet. The computer seems to connect to the network OK (I have tried both wired and wireless), but I can't visit sites and can't ping web addresses. Pinging the router fails, as does pinging another of my computers on the network. I have never encountered something like this before, and whilst I am no noob I am also not a sysadmin, haha. :( Any help is greatly appreciated, thank you for your time. P.S. I have tried a system restore (newbie move?).

    Read the article

  • Apache process consumes too much CPU

    - by Niro
    I have an ubuntu apache/php server running php doing appx 100 hits/sec and a PHP cron running in the background. I get occasionally high CPU load on one of the Apache processes which stays high regardless of traffic or cron activity. It seems to me that its stuck in some kind of loop or something. Below you will find the top and strace info. How can I find where the bad code is and what causes this? top - 14:45:24 up 3 days, 3:38, 1 user, load average: 5.10, 5.88, 5.85 Tasks: 163 total, 5 running, 158 sleeping, 0 stopped, 0 zombie Cpu(s): 47.8%us, 18.5%sy, 0.0%ni, 10.2%id, 0.0%wa, 0.0%hi, 1.8%si, 21.6%st Mem: 7885012k total, 3858484k used, 4026528k free, 177444k buffers Swap: 0k total, 0k used, 0k free, 1037868k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 10736 www-data 20 0 769m 559m 478m R 69 7.3 29:08.30 apache2 10844 www-data 20 0 824m 601m 492m S 17 7.8 4:37.90 apache2 1016 root 20 0 242m 25m 4628 S 6 0.3 162:07.93 scalarizr 9030 www-data 20 0 879m 619m 492m S 4 8.0 5:06.82 apache2 20216 www-data 20 0 747m 228m 170m S 4 3.0 0:01.94 apache2 10807 www-data 20 0 814m 584m 492m S 3 7.6 4:54.10 apache2 10455 www-data 20 0 831m 574m 492m S 3 7.5 4:32.65 apache2 10495 www-data 20 0 849m 592m 492m S 3 7.7 4:41.10 apache2 10884 www-data 20 0 840m 581m 492m S 3 7.6 4:25.06 apache2 ^CProcess 10736 detached % time seconds usecs/call calls errors syscall ------ ----------- ----------- --------- --------- ---------------- 74.55 0.148052 1 109755 gettimeofday 25.36 0.050370 0 164634 clock_gettime 0.09 0.000178 0 54878 poll ------ ----------- ----------- --------- --------- ---------------- 100.00 0.198600 329267 total root@ec2-67-202-54-36:~# ^C

    Read the article

  • NTOP gives warnings on startup

    - by FR6
    I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

    Read the article

  • Netgear GS724Tv3 and link aggregation Mac OS X Server 10.6.8

    - by Manca Weeks
    I need to link aggregate 2 sets of ports on the Netgear GS724T with my Apple server tower (latest generation). I have 2 built in ports and 2 ports on a PCIe ethernet card. It is not obvious to me how to properly configure the Netgear end. I have access to the Netgear box through its web interface, just don't know how to properly set the settings. I tried going to Netgear for help, but they said my software support has expired. I bought this unit on their recommendation - they say it is compatible with 802.3ad protocol. I cannot locate any references to this protocol in the manual and I noticed some people in formus say that this device is actually not compatible with 802.3ad and that Netgear is misleading potential customers by saying it is. Any help will be appreciated. Thanks, M My own answer - posted as edit because of restrictions on my user: OK folks, turns out one must use a Windows machine on this one or nothing makes sense. I was unable to get much farther than viewing the default inactive LAGs because in Firefox and Safari on Mac things don't make much sense - i.e. the Apply buttons (supposedly JavaScript) don't work. You can view the configurations, but none of the modifications you make stick. Then, in Switching - LAGs, choose the ports to include and make sure you switch the LAG type from Static to LACP and all is well. Haven't tested the performance of the config yet, but both sides appear to be happy with the configuration. Apple server says link active and so does the Netgear. Will report if any other discoveries. Thanks for all who read and to user84104 for responding. M

    Read the article

  • Kindle (client) for Mac

    - by doug
    So we're clear, i'm talking bout the client/software version here--ie, that you install on your Mac or PC--not the device. The Kindle client was recently released for the Mac. I bought a couple of Kindle-edition books and i'm reading them using this client. Astonishingly, two features i consider to be more or less essential to any ebook reader are missing in the Kindle client, either that, or i can't find them: (i) text searching; and (ii) highlighting text. First, does anyone know how to access the search feature? I'm aware of the "Go To" button at the top middle of the reader window--the options in that menu when you click the button are: "Cover", "Table of Contents", "Beginning" and "Location." "Location" requires that you type in an integer (but it doesn't correspond to page number--e.g., typing "167" brought me to the table of contents), not a search term. Second, there's a button on the upper right-hand corner of the window "Show Notes and Marks" yet i can't find any way to highlight text. The only kind of "note" or "mark" i have been able to record is to "bookmark" a page by clicking the "bookmark" button also at the top of the window.

    Read the article

  • Eee PC Seashell series netbook screen is cut off at bottom no matter the resolution

    - by Yzmir Ramirez
    I have an Eee PC 1015PE Seashell netbook running Windows 7 Home Premium with an Intel Graphics Media Accelerator 3150 (8.14.10.2230) with a "Generic Non-PnP Monitor" detected. I tried: Changing the resolution (Control Panel = Appearance and Personalization = Display = Screen Resolution) to 1024x768 Updating the video driver (to 8.14.10.2230) Uninstalling the driver and rebooting Pressing the Windows Key + "-" (magnifier) Pressing Ctrl + Mouse Scroll only resizes the desktop items Pressing Fn + F4 shows 1024x600 (which I think is what I should be using, but nothing happens) EDIT: Changed from Landscape to Portrait and it works Attached an External Monitor and when I extend or set as desktop it works only on the External Monitor (shows up as "Generic PnP Monitor in Device Manager) Basically the bottom inch of my desktop is off-screen hiding my start bar, but my wigets are in their proper position (the start bar is not hidden). Pressing Ctrl + Esc shows the start menu but its cut-off. I'm pretty sure I should be using 1024x600 resolution, any advice? What's odd is that this only started happening recently. EDIT2: Here are some screenshots showing the problem: Resized Window to fit: Opened Start Menu - notice it cut off: Maximized window and then scrolled down - notice no Start Menu: I downgraded my graphic driver I downloaded from the Intel Download Center for the Graphic Media Accelerator 3150 (now: 8.14.10.1972) and now my "Generic non-PnP Montior" detects as "Digital Flat Panel (1024x768 60Hz)".

    Read the article

  • Can I get ethernet out of my Verizon FIOS set-top box?

    - by Tom Hughes
    Setup: my home network is long & skinny, and the FIOS-connected router is all the way at one of the apartment. At the other end, far away (and a floor higher) is my HD TV, which gets a cable-TV signal from a Verizon set-top box that is coax-connected back to the FIOS on-premises equipment. Wi-Fi won't work, the apartment is too stretched out, with old, thick walls and floors. Goal: I think there are three ways to get ethernet back to where the HD TV is: 1) run a cable! this isn't crazy but isn't cheap either (my building won't let me do it, it involves hiring an electrician because the cable would run partly through the public hallway ceiling) 2) split the coax near the TV and put in... a MoCA device? 3) somehow tease the set-top box, which has an RJ-11 (ethernet) port on the back, to give me network access. Question: any other choices? and, is one choice better than the others? #3 is by far the most desirable because it would involve the least wiring -- but I can't find any resources to help make it happen. #2 is a bit scary, I don't want to degrade service to the TV or anywhere else for that matter.

    Read the article

  • Lucid Lynx login issue

    - by Bart Silverstrim
    Recently upgraded from Karmic to Lynx. Upgrade seemed to go well, no noticeable issues. I logged in, and my window manager wasn't starting. An application would appear, but sans control buttons and border, so figured the windows manager needed to be given a swift kick. Opened a web browser and a quick google had me run "metacity --replace &" and everything popped up. I re-ran the Compiz configuration tool to enable my rotating desktop cube to the way I liked it, and had to reconfigure my desktop switcher to the right number of desktops (although the first time I ran it, it crashed on the panel and reloaded...odd, but once it relaunched it seemed fine.) Today I installed updates, rebooted and logged in for the second time since my upgrade. Again, the window manager was dead, and my compiz settings were gone, and the workspaces were set back to four (and when I clicked on the preferences to change them, it crashed on the panel and reloaded again). Resetting everything made things look somewhat normal again. I'm guessing it'll work until I reboot again. Googling around isn't turning up similar complaints about Lucid Lynx and the window manager. Before I go deleting preference files, anyone else know of this kind of issue and what could be done about it? Or should I start taking the stab in the dark approach of deleting preference files hoping one of them is corrupt or has something unsupported in it that's throwing LL for a loop?

    Read the article

  • Possible to host CentOS netinstall files on a local HTTP/FTP?

    - by garlicman
    I'm running XenServer on an Dell R610 and am running into a catch-22. During install from DVD, CentOS can't find the DVD package catalogue. It's a reported error for some, XenServer + CentOS6 + DVD install in some hardware configurations = failed install. Yes, I checked the MD5 and let the disc test pass. In every reported case, the netinstall was the solution. The issue is my net access is required to go through a web proxy that prompts before you can download a file. This naturally breaks any download automation. I've been waiting on our IT to put in an exception rule to allow my lab to bypass the prompt, but it's been over 3 weeks now and they don't seem responsive. (I've been working on this a day or two a week) I want to try and host the netinstall files local in my Xen network. Right now I only have a bunch of Windows based VMs, CentOS won't install so I don't have any Linux tools. I had tried simply hosting all the DVD contents off one of the Windows servers using Mongoose. (I didn't want to setup IIS) I copied them to a hosted sub-directory similar to all the mirrors out there (e.g. http:///centos/6.2/os/i386/) with no auth or anything. Then in the netinstall I correctly pointed to it. I now realize just copying the DVD files over won't work. The repodata will point to a local device, not the site I'm hosting. (e.g. the DVD repodata includes xml that points to where the packages are) Clearly I'm hosting them over HTTP, not from a DVD. Is there an easy way to sort this out? I'm just trying to install CentOS6 on Xen. If there's a turnkey downloadable Xen image with CentOS 6.2 on it, or a downloadable repo image, I'll take that too! Thank you in advance!

    Read the article

  • Is current SATA 6 gb/s equipment simply unreliable?

    - by korkman
    I have a 45-disk array of Seagate Barracuda 3 TB ST3000DM001 (yes these are desktop drives I'm aware of that) in a Supermicro sc847 JBOD, connected via LSI 9285. I have found a solution for the problem description below by reducing speed via MegaCli -PhySetLinkSpeed -phy0 2 -a0; for i in $(seq 48); do MegaCli -PhySetLinkSpeed -phy${i} 2 -a0; done and rebooting. The question remains: Is this typical for current 6 gb/s equipment? Is this the sad state of SATA storage? Or is some of my equipment (the sff-8088 cables come to mind) bad? The Problem was: Synchronizing HW RAID-6, disks kept offlining. Fetching SMART values reveiled that those which offlined did not increase powered-on hours anymore. That is, their firmware (CC4C) seems to crash. Digging into the matter by switching to Software RAID-6, with the disks passed-through, I got tons of kernel messages scattered across all disks, with 6 gb/s: sd 0:0:9:0: [sdb] Sense Key : No Sense [current] Info fld=0x0 sd 0:0:9:0: [sdb] Add. Sense: No additional sense information And finally, when a disk offlines: megasas: [ 5]waiting for 160 commands to complete ... megasas: [35]waiting for 159 commands to complete ... megasas: [155]waiting for 156 commands to complete ... megaraid_sas: pending commands remain after waiting, will reset adapter. Ugly controller reset here, then minutes later: megaraid_sas: Reset successful. sd 0:0:28:0: Device offlined - not ready after error recovery ... sd 0:0:28:0: [sdu] Unhandled error code sd 0:0:28:0: [sdu] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK sd 0:0:28:0: [sdu] CDB: Read(10): 28 00 23 21 2f 40 00 00 70 00 sd 0:0:28:0: [sdu] killing request Reduced speed to 3 gb/s like written above, all problems vanished.

    Read the article

  • How to reinstall Windows Boot Manager on EFI partition

    - by joaocandre
    So I've been trying to install Ubuntu on a second HDD on my desktop, which has W8 installed on a SSD (UEFI-only boot). Thing is, during Ubuntu installation I made the mistake of choosing to install the bootloader (GRUB) to the first disk (the SSD), and after install I could not boot into W8 (the entries in GRUB didn't work). Following these instructions, I managed to be able to get "Windows Boot Manager" back, however I lost GRUB in the process, and got a duplicate "Windows Boot Manager" entry in BIOS, along with the "Ubuntu" entry, which then I used to boot into Ubuntu. Later, I decided to reinstall Ubuntu, and formatted the HDD from within windows, however, the entries in BIOS stayed the same, and, while I had the HDD connected to the motherboard, I could not boot into an Ubuntu Live USB (in order to reinstall Ubuntu). I made another mistake by updating the BIOS, which cleared all of the EFI boot entries in BIOS, and, right now, I get an error when boot from the SSD: grub: device not found (...) So it seems that grub is still installed in the EFI partition of the SSD, and since I don't have the WBM entry in BIOS anymore, I cannot even boot into Windows, and the previous instructions don't work anymore. Is there another way to reset W8 EFI partition to the default?

    Read the article

  • how would it be possible to discover a cable modem's MAC remotely?

    - by amateurenthusiast
    i was reading the back archives of a canadian privacy law blog, and he linked to a judicial decision. apparently as part of an investigation in which were used yahoo chat and google's old 'hello' image trading program the officer was able to determine a suspect's modem's MAC address: In order to determine who STEPHTOSH was, the officer did a trace on a programme called WHO IS in an effort to learn from where STEPHTOSH was coming. WHO IS is a command program available to the public. The officer was able to ascertain that the person using the name STEPHTOSH was a Rogers Internet customer. The officer was able to obtain the Internet Protocol address, also known as the I.P. There is only one location for an I.P., which is unique to that subscriber. By use of the website known as DNS STUFF.com, one is able to find with which company this I.P. is registered. It was ascertained that the I.P. address used by STEPHTOSH was registered to Rogers Cable, from the Toronto area. The officer also learned the Cable Modem MAC address used by STEPHTOSH. This was all the information the officer was able to amass. now it was my understanding that the MAC address of any given device can only be accessed if you're only one 'hop' away on the Internet. the suspect in question was in Markham and the officer part of the Toronto Police, so it's conceivable that they both might have used Rogers internet. but would that still put them only one 'hop' away from each other? i thought the first hop after the modem was usually the ISP? and if he'd used a netBIOS query against this guy's machine it would return the ethernet card's MAC, not the modem's. so is this guy on the same rogers subnet as the suspect's cable modem, is that functionality part of google's Hello (i could only think that it would be possible if Hello operated as a virtual LAN or something), does the officer have remote access to the arp caches of the routers at Rogers or is he just full of crap and lying to make his case stronger?

    Read the article

  • Finding a shared HDD attached to the network from my F-13 machine

    - by Ramy
    Sorry for the slew of n00bie questions, but here is one more. I recently partitioned my 1.5TB harddrive according to this question I then bought this to attach the harddrive to my network. The problem is, how do I navigate to the hard drive to move files over the network to the HDD. should this be moved to serverfault? update: the disk isn't even showing up when i call "fdisk -l" (as root). How can I mount it if I can't even find it? [root@Moonface ~]# /sbin/fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00018598 Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 19458 155777024 8e Linux LVM Disk /dev/dm-0: 53.7 GB, 53687091200 bytes 255 heads, 63 sectors/track, 6527 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/dm-1: 4764 MB, 4764729344 bytes 255 heads, 63 sectors/track, 579 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-1 doesn't contain a valid partition table Disk /dev/dm-2: 101.0 GB, 101032394752 bytes 255 heads, 63 sectors/track, 12283 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-2 doesn't contain a valid partition table

    Read the article

  • Wireless driver activation problem in compaq c700 in ubuntu 9.04

    - by Fazil
    I am using ubuntu 9.04, i cant access my wireless driver, i activate the madwifi in administrationhardware drivers, but i could'nt activated the wireless too. when i type lspci i get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when i tried in windows i found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can i do for solving this problem.

    Read the article

  • USB 3.0 hard disk not detected on a particular host controller?

    - by Alvin Wong
    I have a USB 3.0 hard disk which has always been working on my desktop with an XHCI. Now I just bought a notebook with an XHCI (something with Intel's Ivy Bridge setup). The first time I plug the hard disk in its 3.0 port it is detected and working. A few hours later I try to connect it again, but seems that the notebook just ignored it! The light on the hard disk didn't blink as usual (instead it is hold at on). I then tested it with my desktop again and it is working perfectly. It gets trickier when I plug it in the USB 2.0 port of that notebook it is detected and working perfectly (despite the slower speed). Then I try to plug in an USB 2.0 USB flash drive to that USB 3.0 port, and it is detected (of course as USB 2.0). So, there are two USB 3.0 ports on my notebook's XHCI. Both of them are not working with my hard disk but working perfectly fine with my USB 2.0 UFD. What's wrong with it? When I plug in the hard disk, device manager doesn't change. I've tried re-installing the driver for the XHCI, but it changes nothing. Had I broke the USB 3.0-specific pins of both USB 3.0 ports?

    Read the article

  • Router block some sites

    - by Mahesha999
    Hi I was using ADSL Modem/Router earlier. The device is quite old Pronet PN-ADSL 101 E/U model (pics: http://bit.ly/P2YaWy, http://bit.ly/OA700l) Since it had only one RJ45 out, I bought new Wireless Router TPLink TL-WR941ND. It has 4 RJ45 out and 3 wireless antennas. I configured my old router in bridge. Now, if I have to connect my pc to Internet through the old router, I have to enter username and password. Then I connected the RJ45 output of old router to the WAN in of new router. and ran the CD of new router. It configured the new router in PPPoE by saving the username and password in router to dial automatically. So now I have to just plug in the wires in my new routers any RJ45 out. I am able to access the Internet when I connect through new router (both wired and wirelessly), but some sites are getting blocked. Most notably yahoo.com (though ymail.com is working), Microsoft.com. msn.com. These sites work perfectly fine when I connect my pc directly to my old router and enter username and password manually. (However others like google.com. facebook.com works fine when connect through new router) So here these some sites need some parameter set but I am unable to find them out. Can anyone help me. My friend said he also faced same problem. Surprisingly he advised me to see if the same websites will work through Opera turbo mode and boom they worked. So what could be the problem?

    Read the article

  • Reliable applicance for routing IT emergency calls (SIP and ISDN)

    - by chiborg
    We have a fairly big IT installation and our IT staff needs to be reachable 24/7. At the moment we have the following setup for "emergency" calls to our IT staff on our main Asterisk box: An incoming emergency number (connected via SIP trunk and a BRI card in case the SIP trunk goes down). When the number is called during the office hours, all the SIP phones of the IT staff are called simultaneously. When the number is called out of office hours interface, a list of mobile phone numbers is called, one after another until someone picks up. The list can be changed by the IT staff via command line script. The setup works well, but the Asterisk is heavily used in a call center, has experienced some outages and misconfigurations, each of them bringing down the IT emergency number. So we'd like to put the IT emergency call functionality on a separate device. This does not need to be a big server, it even does not need to be Asterisk, it only has one purpose and should do it reliably. It should be very low-maintenance. Any suggestions for hard- and software?

    Read the article

  • Microsoft SQL Server Management Studio causing system freeze

    - by CRoshanLG
    I'm experiencing very slow response from MSSMS and it causes other applications to slow down. Specially Skype crashes after few seconds from opening MSSMS, showing an error called "Disk I/O Error". I'm regularly using few applications (Sublime text, MS Word, Firefox, Outlook, Skype and one or two other apps) simultaneously. The system works fine when MSSMS is not in use! But as soon as MSSMS is opened, all the apps start to freeze (MSSMS also responds very slow). This problem has been there for about a week now (I haven't installed any apps or haven't made any changes to the system during that time). -- System Specifications -- Processor: Core i3 (3.1 GHz) RAM: 4 GB OS: Windows 7 Professional (64 bit) Free space in C drive: ~ 100 GB MS SQL Server 2008 R2 Microsoft SQL Server Management Studio version - 10.50.1600.1 I've tried to find a reason for this but there are no helpful information in the web! There are some solutions suggested (in forums and in Skype Support pages) for the Skypes' "Disk I/O Error", all of which I tried but does not solve the problem. Has anyone faced the same senario? (and hopefully) knows a solution? Systems Log I don't have much knowledge in interpreting the System Log, but I think the Critical and Warnings are not helpful. But there are lots of Error logs which might be useful. In source Kernal-General there are few similar errors saying "An I/O operation initiated by the Registry failed unrecoverably.The Registry could not flush hive (file): <some file>" In source atapi also there are few similar errors -- "The driver detected a controller error on \Device\Ide\IdePort0." (all errors has occurred in 'IdePort0') In Application Error, there are several errors logged, and following is the latest one. Both the Errors which has occurred today is similar (to this one). As it is from Ssms.exe, I guess this is relevant to the cause of problem. But as I said above I can't understand what it means!

    Read the article

  • Hyper-v on 2012R2 startup gen1 vm causes the host to freeze up

    - by sputnik
    I've searched a lot to resolve the following issue, but nothing helped me. My problem is, that starting up a first-gen vm locks up the whole host. Only a hard reset helps. Second-gen vm starts and runs perfectly. The freezes happened on 3 different vms. FreeBSD, Ubuntu, Windows Server 2008R2, while Windows 8.1 on second gen config works perfectly. Im using this pc mainly as a workstation. No eventlog errors nor dumps are generated. My system: Windows Server 2012R2 FX-8350, non OC ASRock 870 Extreme R2 (Crappy board imho) 32GB DDR3 1866@1600 (My motherboard, against the "support" for 1866ram won't work with full speed) 120GB SSD 4.5TB Storage space device I dont think that its due to my system, because vmware workstation was running without problems. Did I forget to configure something? Any help is appreciated. P.S: Even deactivating C1E, C6, C&Q didnt work. P.P.S: With no virtual network adapter set, the system still locks up. Creating a first gen vm without any hdds and network and launching works. Attaching a boot dvd causes the host to freeze. The host freezes as the gen1 vm begins to boot, doesn't matter if from dvd or hdd

    Read the article

  • Tidy up old Windows Server Backup snapshots

    - by dty
    Hi, I'm running wbadmin from a scheduled job, backing up my C: and D: drives to my E: and (I believe!) including the system state: wbadmin start backup -backuptarget:e: -include:c:,d: -allCritical -noVerify -quiet I'd like to delete old backups, but I'm concerned that all the information I can find says to use wbadmin to delete old system state backups, and vssadmin to delete other backups. As far as I know, my backups ARE system state backups, but are using VSS on E: for storage, so I'm worried about trying either of these techniques for fear of losing all my backups. This is a home network, so I don't have a spare server to test this on. I'm also happy to simply restrict the space used on E:, but I can't make sense of the difference between the /for and /on parameters of the relevant vssadmin command. For reference, here's the output of vssadmin show shadows: Contents of shadow copy set ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Contained 1 shadow copies at creation time: 07/01/2011 08:12:05 Shadow Copy ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Original Volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Volume: \\?\GLOBALROOT\Device\HarddiskVolumeShadowCopy83 Originating Machine: x.y.com Service Machine: x.y.com Provider: 'Microsoft Software Shadow Copy provider 1.0' Type: DataVolumeRollback Attributes: Persistent, No auto release, No writers, Differential [... repeated a lot...] vssadmin show shadowstorage: Shadow Copy Storage association For volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 5.859 GB Shadow Copy Storage association For volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 40.317 GB Shadow Copy Storage association For volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 168.284 GB Allocated Shadow Copy Storage space: 171.15 GB Maximum Shadow Copy Storage space: UNBOUNDED wbadmin get versions: Backup time: 07/01/2011 03:00 Backup target: 1394/USB Disk labeled xxxxxxxxx(E:) Version identifier: 01/07/2011-03:00 Can Recover: Volume(s), File(s), Application(s), Bare Metal Recovery, System State [... repeated a lot...]

    Read the article

  • No audio in my ubuntu system

    - by hap497
    Hi, I am running ubuntu 9.10. But there is no sound in my environment. When I go to System-Preference, there is no 'sound' entry there. $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: I82801AAICH [Intel 82801AA-ICH], device 0: Intel ICH [Intel 82801AA-ICH] Subdevices: 1/1 Subdevice #0: subdevice #0 $ lsmod Module Size Used by usb_storage 52576 3 binfmt_misc 8356 1 vboxvfs 34620 0 vboxvideo 1884 1 drm 159584 2 vboxvideo agpgart 34988 1 drm snd_intel8x0 30168 2 snd_ac97_codec 101216 1 snd_intel8x0 ac97_bus 1532 1 snd_ac97_codec snd_pcm_oss 37920 0 snd_mixer_oss 16028 1 snd_pcm_oss snd_pcm 75296 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_seq_dummy 2656 0 snd_seq_oss 28576 0 iptable_filter 3100 0 snd_seq_midi 6432 0 ip_tables 11692 1 iptable_filter x_tables 16544 1 ip_tables snd_rawmidi 22208 1 snd_seq_midi snd_seq_midi_event 6940 2 snd_seq_oss,snd_seq_midi ppdev 6688 0 snd_seq 50224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event snd_timer 22276 2 snd_pcm,snd_seq snd_seq_device 6920 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq psmouse 56500 0 serio_raw 5280 0 snd 59204 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_ oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_ti mer,snd_seq_device i2c_piix4 9932 0 parport_pc 31940 0 soundcore 7264 1 snd snd_page_alloc 9156 2 snd_intel8x0,snd_pcm vboxguest 143836 7 vboxvfs lp 8964 0 parport 35340 3 ppdev,parport_pc,lp pcnet32 32644 0 mii 5212 1 pcnet32 floppy 54916 0 ~:987:2$ lspci 00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02) 00:01.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] 00:01.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter 00:03.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 40) 00:04.0 System peripheral: InnoTek Systemberatung GmbH VirtualBox Guest Service 00:05.0 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio Controller (rev 01) 00:06.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB 00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 0 00:0b.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller ~:988:3$

    Read the article

  • Cannot set video resolution above 640x480 after installing Windows XP SP2

    - by waanders
    I've installed Windows XP SP2 on a computer (there was not SP at all). Now the display settings are set back to 640x480 and 4 bits colors. And I can't change it, it's the only option in Settings tab of the Display dialog of Windows. The screen look awful now, how can I solve this problem? UPDATE: Seems to be a problem with the video driver (thanks @Karan and @Hennes). I did run Speccy (PC-Wizard freezes the computer) and this is a part of the log file: Summary Operating System Microsoft Windows XP Professional 32-bit SP3 CPU Intel Celeron Willamette 0.18um Technology RAM 512 MB DDR @ 133MHz (2.5-3-3-6) Motherboard COMPAQ 0838h (FC-478) Graphics Standard Monitor (640x480@1Hz) Hard Drives 19.0GB Maxtor 2B020H1 (PATA) Optical Drives No optical disk drives detected Audio No audio card detected ... Graphics Monitor Name Standard Monitor on Current Resolution 640x480 pixels Work Resolution 640x450 pixels State enabled, primary Monitor Width 640 Monitor Height 480 Monitor BPP 4 bits per pixel Monitor Frequency 1 Hz Device \\.\DISPLAY1 OpenGL Version 1.1.0 Vendor Microsoft Corporation Renderer GDI Generic GLU Version 1.2.2.0 Microsoft Corporation Values GL_MAX_LIGHTS 8 GL_MAX_TEXTURE_SIZE 1024 GL_MAX_TEXTURE_STACK_DEPTH 10 GL Extensions GL_WIN_swap_hint GL_EXT_bgra GL_EXT_paletted_texture GL_EXT_bgra

    Read the article

  • MAMP Pro .xip.io, fixing urls with htaccess

    - by user3540018
    I've got all my websites set up with MAMP Pro. For instance, I got it set up, so when I go to example.com, the browser displays the website that's set up on my iMac. Now, I wanna get MAMP Pro to work so I can view my website on my other computers/devices (which are all hooked up on the same network.) So far all I had to do is check the checkbox "via Xip.io (LAN only)", and now I can view my website on my other computers/devices within my LAN by simply going to example.com.10.0.1.13.xip.io. Problem is, whenever I'm on this other computer/device, when I click on the links, I get 404 error. ie. whenever I go to example.com/news, I get the 404. But when I go to example.com.10.0.1.13.xip.io/news, THEN I get the right page. So in order to solve my problem I need to rewrite the urls. So whenever someone clicks on a link ie. goes straight to example.com/news, he'll go to example.com.10.0.1.13.xip.io/news. I don't want to change all the links in my MySQL file, but I believe I can do it simply with the htaccess file. I've opened the htaccess file and added the last two lines, but it just doesn't work. <IfModule mod_rewrite.c> RewriteEngine On # Send would-be 404 requests to Craft RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !^/(favicon\.ico|apple-touch-icon.*\.png)$ [NC] RewriteRule (.+) index.php?p=$1 [QSA,L] RewriteCond %{HTTP_HOST} ^example\.com RewriteRule ^(.*)$ http://www.example.com.10.0.1.13.xip.io/$1 [R=permanent,L] </IfModule> Or perhaps I don't need to change the htaccess file, is there something that I could be missing in the MAMP Pro settings, or perhaps a MAMP extension that I need?

    Read the article

  • 530 5.7.1 Client was not authenticated Exchange 2010 for some computers within mask

    - by user1636309
    We have a classic problem with Client not Authenticated but with a specific twist: We have an Exchange 2010 cluster, let's say EX01 and EX02, the connection is always to smtp.acme.com, then it is switched through load balancer. We have an application server, call it APP01 There are clients connected to the APP01. There is a need for anonymous mail relay from both clients and APP01. The Anonymous Users setting of the Exchange is DISABLED, but the specific computers - APP01 and clients by the mask, let's say, 192.168.2.* - are enabled. For internal relay, a "Send Connector" is created, and then the above IP addresses are added for the connector to allow computers, servers, or any other device such as a copy machine to use the exchange server to relay email to recipients. The problem is that the relay works for APP01 and some clients, but not others (we get "Client not Authenticated") - all inside the same network and the same mask. This is basically what we do to test it outside of our application: http://smtp25.blogspot.sk/2009/04/530-571-client-was-not-authenticated.html So, I am looking for ideas: What can be the reason for such a strange behaviour? Where I can see the trace of what's going on at the Exchange side?

    Read the article

  • Expand disk space on Ubuntu 10.04 (VMWare Guest)

    - by Jason Clawson
    I need to resize the disk space of an ubuntu guest in VMWare Workstation. After using the expand disk utility in vmware workstation, I need to do some linux magic to resize the parition. I have searched and found a lot of posts about resizing it. Unfortunately I don't really understand it all that well. Can anyone help me out with this? df -h gives me: Filesystem Size Used Avail Use% Mounted on /dev/mapper/ubuntu-root 19G 2.6G 16G 15% / none 496M 172K 495M 1% /dev none 500M 0 500M 0% /dev/shm none 500M 64K 500M 1% /var/run none 500M 0 500M 0% /var/lock none 500M 0 500M 0% /lib/init/rw none 19G 2.6G 16G 15% /var/lib/ureadahead/debugfs /dev/sda1 228M 36M 181M 17% /boot lvs says: LV VG Attr LSize Origin Snap% Move Log Copy% Convert root ubuntu -wi-ao 18.88g swap_1 ubuntu -wi-ao 884.00m fdisk -l says: Disk /dev/sda: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00033718 Device Boot Start End Blocks Id System /dev/sda1 * 1 32 248832 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 32 2611 20719617 5 Extended /dev/sda5 32 2611 20719616 8e Linux LVM I really appreciate the help.

    Read the article

< Previous Page | 574 575 576 577 578 579 580 581 582 583 584 585  | Next Page >