Search Results

Search found 18209 results on 729 pages for 'loop device'.

Page 585/729 | < Previous Page | 581 582 583 584 585 586 587 588 589 590 591 592  | Next Page >

• DPMS does not work: the monitor is not switched off

  - by bortzmeyer

  I have a monitor which was properly switched off by my Debian PC when unused. I attached it to another machine and, this times, it is never switched off. In /etc/X11/xorg.conf, I have: Section "Monitor" Identifier "Generic Monitor" Option "DPMS" It is recognized when X11 starts: (II) Loading extension DPMS ... (II) VESA(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display ... (**) Option "dpms" (**) VESA(0): DPMS enabled The operating system is Debian stable "lenny". The graphics card is: 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrate d Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device 2a6f Flags: bus master, fast devsel, latency 0, IRQ 5 Memory at fe900000 (32-bit, non-prefetchable) [size=512K] I/O ports at b080 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fe800000 (32-bit, non-prefetchable) [size=1M] Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-Capabilities: [d0] Power Management version 2 X11 is: X.Org X Server 1.4.2 Release Date: 11 June 2008 X Protocol Version 11, Revision 0 Build Operating System: Linux Debian (xorg-server 2:1.4.2-10.lenny2) Current Operating System: Linux ludwigVII 2.6.26-2-686 #1 SMP Sun Jun 21 04:57:3 8 UTC 2009 i686 Build Date: 08 June 2009 09:12:57AM

  Read the article

• Backup data from RAID 1 disk out of its server

  - by Doomsday

  I'm facing with a pretty easy problem in my opinion. I've extracted a working disk from a RAID1 and I'm looking to copy only data (FS and RAID configuration doesn't matter) into another location (another FS). My problem is I'm not able to mount properly this disk into another linux. I've first looked the partition table : # fdisk -l /dev/sdc Disk /dev/sdc: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 1249535699 624767818+ fd Linux raid autodetect /dev/sdc2 1249535700 1250017649 240975 fd Linux raid autodetect /dev/sdc3 1250017650 1250258624 120487+ 82 Linux swap / Solaris I've understood I should use dmraid tools. Once installed : # cat /proc/mdstat Personalities : md0 : inactive sdc1[1](S) 624767744 blocks unused devices: <none> And some other informations : # mdadm --examine /dev/sdc1 /dev/sdc1: Magic : a92b4efc Version : 0.90.00 UUID : 8f292f54:7e5aef72:7e5ab5fd:b348fd05 Creation Time : Mon Jun 2 03:39:41 2008 Raid Level : raid1 Used Dev Size : 624767744 (595.82 GiB 639.76 GB) Array Size : 624767744 (595.82 GiB 639.76 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Update Time : Tue Feb 7 22:34:59 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Checksum : a505b324 - correct Events : 15148 Number Major Minor RaidDevice State this 1 8 1 1 active sync /dev/sda1 0 0 8 17 0 active sync /dev/sdb1 1 1 8 1 1 active sync /dev/sda1 From here, I've tried to mount but I'm not comfortable with dmtools and how it's working. # mount /dev/sdc1 /mnt/sdc1 mount: unknown filesystem type 'linux_raid_member' # mount /dev/md0 /mnt/sdc1 mount: /dev/md0: can't read superblock I've seen some options to alter RAID array with mdadm but I only want to copy data on its filesystem before wiping them... Anyone has a clue ?

  Read the article

• Can't connect to Server Manager from Windows 7

  - by SAdmin317

  I have a Windows 7 Pro 64bit with SP1 desktop that has RSAT tools installed. I opened Server Manager and can't connect to the server (Server 2008 R2 core). I followed the guide to enable everything on the server, added a registry key to enable read-only on the device manager as well. On the Windows 7 PC I turned on winrm, did the quick config, and added the server IP and name as trusted hosts. I still get an error when connecting. "Connecting to the remote server failed with the following error message: The WinRM client cannot process the requests. If the authentication scheme is different from Kerberos, or if the client computer is not joined to a domain, then HTTPS transport must be used or the destination machine must be added to the TrustedHosts configuration setting...." I also added the name of the server to the windows 7 /etc/hosts file. Ping the server name translates to the IP of the server. Also opened up the firewall for "Remote Volume Management" Both machines are on the same Workgroup, using the same Administrator account, with the same password. Any help appreciated.

  Read the article

• GUI interfaces to ATI card behave weirdly out of the box and after updates.

  - by jdk

  My Lenovo W500 came with an ATI Mobility FireGL V5700 and both the Catalyst control center software and Vista display manager display four monitors. What's really annoying is the behaviour. My two active displays (laptop display + my external monitor) are always #s 3 and 4 respectively which doesn't make sense. This is out of the box. Additionally dragging & dropping is jumpy and displays #1 and 2 (always inactive because they don't exist to the software) are often preventing me from dragging #3 and 4 to the rightmost side. They also auto-snap to weird positions and certain sensible positions like position one directly over top of the other are not possible. The exact same annoyances are present when using the Windows Display manager too. In other words the interface is crap and I'm looking for a fix that's not wishing I had gone with nVidia instead. I've updated drivers, and Catalyst control centre. Have latest Windows and AMD/ATI updates. Any thoughts? Graphics Software Driver Packaging Version 8.563.2.1-090401a-079160C-Lenovo Provider ATI Technologies Inc. 2D Driver Version 7.01.01.849 2D Driver File Path /REGISTRY/MACHINE/SYSTEM/ControlSet001/Control/Class/{4D36E968-E325-11CE-BFC1-08002BE10318}/0001 Direct3D Version 7.14.10.0630 OpenGL Version 6.14.10.8306 Catalyst® Control Center Version 2009.0401.1328.22301 Graphics Hardware Primary Adapter Graphics Card Manufacturer Powered by ATI Graphics Chipset ATI Mobility FireGL V5700 Device ID 9591 Vendor 1002 Subsystem ID 2126 Subsystem Vendor ID 17AA Graphics Bus Capability PCI Express 2.0 Maximum Bus Setting PCI Express 2.0 x16 BIOS Version 010.088.000.021 BIOS Part Number BK-ATI VER010.088.000.021.034663 BIOS Date 2009/09/30 Memory Size 512 MB Memory Type DDR3 Core Clock in MHz 600 MHz Memory Clock in MHz 700 MHz

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  Hi All, I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: http://superuser.com/questions/12955/how-do-i-remove-the-option-to-eject-sata-drives-from-the-windows-7-tray-icon

  Read the article

• Almost All Xenserver Logical Volumes Disappeared - Recovery?

  - by Alex

  We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top. edit2 Output of vgcfgrestore, but from the rescue system, as there is no root to chroot to. # vgcfgrestore --list VG_XenStorage-x-b4b0-x-x-408b91acdcae File: /etc/lvm/archive/VG_XenStorage-x-x-x-x-408b91acdcae_00000.vg VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *before* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013 File: /etc/lvm/backup/VG_XenStorage-x-x-x-x-408b91acdcae VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *after* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013

  Read the article

• Messed up partitions... system will not boot!

  - by someguy

  I did a really dumb thing. cfdisk threw an error at me saying "FATAL ERROR: Bad primary partition 3: Partition ends in the final partial cylinder", so I installed Partition Table Doctor to see if I could fix the problem. When the program started up, it told me there were problems with my partitions, and asked if I wanted them fixed (cannot remember real message, but I believe it had something to do with the cylinder boundaries), so, blindly, without thinking of the consequences, I did. Now, my system will not boot. I tried booting from the Windows 7 installation CD. I went to install a fresh copy, but it said that "No drives were found". I then opened up diskpart. According to diskpart, there is only one partition, containing one volume, assigned the letter "C". Before, I had four partitions! It is also saying that the file system is RAW. Is there any way I can fix this? I have important data that I do not want to lose. Later on... I tried fdisk with the option -l, which lists the partition table(s), and this is what I got: Ignoring extra extended partition 4 Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 64 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x163df116 Device Boot Start End Blocks Id System /dev/sda1 6 18 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 18 7851 62918572+ 7 HPFS/NTFS /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30403 139203193 7 HPFS/NTFS I don't know if this will help, but it's extra information, at least. Also, this is how I had my partitions: 40MB (Unallocated) 100MB (System Reserved) 60GB (Windows, C:) 40GB (Was reserved for secondary OS) ~132GB (Home, E:)

  Read the article

• My home router randomly disconnects me and I'm unable to reconnect to it

  - by Roy Tang

  It's happened a few times, I'm not sure how to diagnose/debug, so any advise would be appreciated. Symptons: sometimes the router will randomly disconnect; the connection icon on my desktop (wired to the router) gets that yellow "!" symbol that tells me my connection just went down. At this point I'm unable to ping the router. afterwards I try to reset the router by removing then reconnecting the power jack on the router side (this is the fastest way as I can't reset the power strip it's connected to without rebooting my desktop. the router has a reset thingy, but it's one of those things where i have to find a pin to stick into the hole, and when I get disconnected I usually need to get reconnected immediately so I just pull and put back the power jack), but even after that the connection has the same state. after the router reboots, if I try to connect to it using a wifi device like my ipad, the ipad prompts me for the wifi password even though it had already "remembered" all the settings for this router forever after i finally decide to reboot the power strip, and my desktop and the router boot up again, the connection returns to its normal state somewhat and i'm able to connect to it as normal using the desktop and wifi devices. What do I need to check the next time this happens so I can figure out the problem? Is it possibly because we've been using the power jack on the router as an easier way to reboot it? Should I be shopping around for a new router? If it helps, the router is a DLink DIR-300

  Read the article

• Move EFI System Partition to another drive

  - by Pincopallino

  I had a Windows 8 installation on an HDD, using UEFI as boot. The HDD has the following GPT table: DISKPART> list partition Partizione ### Tipo Dim. Offset --------------- ---------------- ------- ------- Partizione 1 Ripristino 300 Mb 1024 Kb Partizione 2 Sistema 100 Mb 301 Mb Partizione 3 Riservato 128 Mb 401 Mb Partizione 4 Primario 390 Gb 529 Mb Partizione 5 Primario 540 Gb 390 Gb (I apologize it's in Italian, but the translation is quite straightforward). I recently bought an SSD drive, connected it and installed a fresh Windows 8. Now I have a working dual boot, but the UEFI partition is on the HDD instead of the SSD. Here's the SDD partition list: Partizione ### Tipo Dim. Offset --------------- ---------------- ------- ------- Partizione 1 Riservato 128 Mb 1024 Kb Partizione 2 Primario 221 Gb 129 Mb I think that the best solution would be to have it on the SSD for two reasons: the first is performance (I guess it would be a little be faster on the SSD due to the spin up time for an HDD, but I may be wrong about that) second reason is consistency. As I plan to use only the Windows 8 installation that is located on the SSD and I'm probably going to erase the system partition on the HDD to use it as a data storage device, I think that the boot partition should be on the same drive as the OS. So the question is how do I move the EFI System Partition to the SSD?

  Read the article

• Snapshotting single disk of running Hyper-V VM

  - by modelnine

  I'm currently somewhat at a loss of how to create a snapshot of a single virtual hard-disk of a running Hyper-V VM. Generally, creating a differential disk while a server is shut down is no problem (i.e., call the new-vhd cmdlet and pass a ParentPath, then update the VHD-binding of the respective VM-device), but while the host is running, all I can find is checkpointing the VM as a whole (which creates snapshots of all attached disks), and leaves the VM-state in a form which isn't easily processable by external tools (i.e., it requires reading additional meta-data from the VM). Generally, what'd I'd like to happen for a single-disk snapshot (in my understanding) is: Pause the VM Rename current disk to some other name which specifies it as a base-snapshot Create a new VHD which has the renamed VHD as parent path and is marked as "current" Swap the VHD for the VM for the snapshotted hard-disk to the newly created differential VHD Resume the VM Is there any means to do this programatically? Update: I've seen that this is actually possible with SCSI-disks, i.e. pause the VM, remove the SCSI disk, make the snapshot, reattach the SCSI disk at the same position, resume the VM. And, the VM resumes properly. But: is something similar also possible with G1 machines for the boot disk which is always IDE?

  Read the article

• Hard Drive that was used before not detected or accessible in Windows 7

  - by Anders

  Hello SU: My PC crashed for some unknown reason, and I am still working on what caused that. However, I pulled my main (windows) drive from my computer and hooked it up to my roommate's machine and was able to pull the data I needed off of it (i.e. the drive is good). I hook up his drives as they were, I had to turn off his machine and unplug his secondary drive to hook mine up, boot his machine and there is no second drive available in windows explorer. I opened Device Manager to see if for some reason it's drive letter got un-assigned, but there is nothing listed in there except his primary hard drive, his optical drive and one other optical drive which I believe is the virtual drive Daemon Tools made. The drive shows up in the BIOS, however after I restarted his machine again it sits on the "Entering setup....." screen at the load window. The only thing I can think of is that may have messed with stuff is I used this tutorial to create a bootable XP install on a USB drive to install XP on my machine (I am 99% certain that the optical drive in my PC is broken) and maybe it used the other hard drive's letter for the USB drive for some reason, which doesn't make much sense since it was recognized it as a different drive letter before I started the process. It is possible that it used the secondary hard drive's letter for it's work, but once again I am uncertain. Where should I go from here? He his bound to wake up within the next several hours and will probably flip a lid if I cannot get some sort of handle on this. Any and all help is greatly appreciated. PS: Anyone who helps me get this situated has a beer or two on me, as long as you are in the greater metro Detroit area, or don't mind traveling a bit!

  Read the article

• Ubuntu xrandr rotate issue

  - by user83544

  I've just bought a second monitor for my PC which happens to be a pivot monitor. I've already read lots of forums related to my problem but haven't come across a solution - I have the same symptoms as dozens of posts but no matter whatever I try it just doesn't work. I've already changed the xorg.conf file and added in the device section just under Driver "nvidia" the following for my second monitor: Option "RandRRotation" "on" When I save and reboot I try to rotate my screen with the nvidia X server settings by choosing the second monitor and clicking either "left" or "right" for the rotation. It immediately exits the nvidia settings window and does nothing. I tried within the terminal by typing: xrandr -o right I get the following error: X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 154 (RANDR) Minor opcode of failed request: 2 (RRSetScreenConfig) Serial number of failed request: 14 Current serial number in output stream: 14 I actually manage to rotate it with Option "Rotate" "CCW" instead of "RandRRotation". The problem with this solution is that you get the second monitor in the right position, but any window you open on that screen is practically unchangeable. You can't change the size nor move it, making it useless for reading PDFs, which is the main reason why I bought this second screen to help me write my thesis. Any help is really appreciated. sudo lshw -c video hiram@hiram-linux:~$ sudo lshw -c video *-display description: VGA compatible controller product: nVidia Corporation vendor: nVidia Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:16 memory:f8000000-f9ffffff memory:d8000000-dfffffff memory:d4000000-d7ffffff ioport:dc00(size=12 memory:fbd80000-fbdfffff

  Read the article

• Network topology for both direct and routed traffic between two nodes

  - by IndigoFire

  Despite it's small size, this is the most difficult network design problem I've faced. There are three nodes in this network: PC running Windows XP with an internal WiFi adapter.Base station with both WiFi and a Wireless Modem (WiModem)Mobile device with both WiFi and WiModem The modem is a low-bandwidth but high-reliability connection. We'd like to use WiFi for high-bandwidth stuff like file transfers when the mobile is nearby, and the modem for control information. Here's the tricky part: we'd like the wifi traffic to go directly from the mobile to the PC, as rebroadcasting packets on the same WiFi channel takes up double the bandwidth. We can do that with a manual configuration by giving the both the PC and the base station two IP addresses for their WiFi interfaces: one on a subnet shared with the mobile, and one on their own subnet. The routes on the PC are set up so that any traffic going to the mobile via WiModem goes through the secondary IP address so that return traffic from the mobile also goes through the WiModem. Here's what that looks like: PC WiFi 1: 192.168.2.10/24 WiFi 2: 192.168.3.10/24 Default route: 192.168.2.1 Base Station WiFi 1: 192.168.2.1/24 WiFi 2: 192.168.3.1/24 WiModem: 192.168.4.1/24 Mobile WiFi: 192.168.3.20/24 WiModem: 192.168.4.20/24 We'd like to move to having the base station automatically configure the mobile and PC, as the manual setup is problematic when you start having multiple mobiles and PCs. This means that the PC can only have 1 IP address and needs to be treated as being pretty simple. Is it possible to have a setup driven by DHCP on the base station that is efficient with bandwidth?

  Read the article

• Fixing a corrupted Windows Server 2003 server

  - by Keith

  I have a Windows Server 2003 server that is being mainly used for some reporting done in SQL Server. Recently Windows has started complaining about being corrupted, we are getting an NTFS error 55: The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume \Device\HarddiskVolume1. The server is RAID 5 and I did have a disk die however the RAID never went degraded since I have a hotspare. I replaced the hot spare and I'm still having problems. When I run chkdsk I get tons of messages.. some are: Deleting corrupted attribute record (128, "") from file record segment 194746 Those go on for a while. Then it deletes some orphan files. Then it does Correcting error in index $I30 for file 132426 And that goes on for a while. Then I get tons of Recovering orphaned file RE1AB6~1.LOG into directory file 534959 I have seen a lot of errors relating to the SQL Server reporting services. What are my options at this point? I would prefer to fix the issue instead of building a new server but I don't know if I can at this point.

  Read the article

• vmware player won't run on CentOS due to missing /dev/vmmon, what could be the problem?

  - by Graphics Noob

  So I've tried installing vmware player 3.1.4 and 3.1.3 and both times had the same problem, when I try to load a VM I get the error "Could not open /dev/vmmon". When I ls /dev/ I can see there is no "vmmon" device present. When I try running: sudo /etc/init.d/vmware start I get the output: Starting VMware services: VMware USB Arbitrator [ OK ] Virtual machine monitor [FAILED] Virtual machine communication interface [ OK ] VM communication interface socket family [ OK ] Blocking file system [ OK ] Virtual ethernet [FAILED] which shows that the Virtual Machine Monitor fails to load. I tried following the advice on this site and ran vmware-modconfig --console --install-all I notice during the compilation there are no errors, but at the end I get the message: Starting VMware services: VMware USB Arbitrator [ OK ] Virtual machine monitor [FAILED] Virtual machine communication interface [ OK ] VM communication interface socket family [ OK ] Blocking file system [ OK ] Virtual ethernet [ OK ] Unable to start services Out of curiousity I tried: sudo /sbin/insmod /lib/modules/2.6.18-238.9.1.el5xen/misc/vmmod.ko But got the error message: insmod: error inserting 'vmmon.ko': -1 Invalid module format I have a feeling this may be the root of the problem, but I don't know what could be causing it or how to fix it.

  Read the article

• Replace Linux Boot-Drive | ext3 to btrfs

  - by bardiir

  I've got a headless server running Debian Linux currently. Linux vault 3.2.0-3-686-pae #1 SMP Mon Jul 23 03:50:34 UTC 2012 i686 GNU/Linux The root filesystem is located on an ext3 partition on the main harddrive. My data is located on multiple harddrives that are bundled to a storage pool running with btrfs. UUID=072a7fce-bfea-46fa-923f-4fb0827ae428 / ext3 errors=remount-ro 0 1 UUID=b50965f1-a2e1-443f-876f-578b5f93cbf1 none swap sw 0 0 UUID=881e3ad9-31c4-4296-ae60-eae6c98ea45f none swap sw 0 0 UUID=30d8ae34-e2f0-44b4-bbcc-22d761a128f6 /data btrfs defaults,compress,autodefrag 0 0 What I'd like to do is to place / into the btrfs pool too. The ideal solution would provide the flexibility to boot from any disk in the system alike, so if the main drive fails I'd just need to swap another one into the main slot and it would be bootable like the main one. My main problem is, everything I do needs to result in a bootable system that is open to ssh logins via network as this server is 100% headless so there is no possibility to boot it from a live cd or anything like that. So I'd like to be extra sure everything works out fine :) How would I best go about this? Can anybody hint me to guides or whip something up for these tasks? Anything I forgot to think about? Copy root-data into btrfs pool, adjust mountpoints,... Adjust GRUB to boot from btrfs pool UUID or the local device where GRUB is installed Sync GRUB to all harddrives so every drive is equally bootable (is this even possible without destroying the btrfs partitions on the drives or would I need to disconnect the drives, install grub on them and then connect them back with a slightly smaller partition?)

  Read the article

• Apache using 100% CPU, once again

  - by CBenni

  Recently, apache2 started using 100% of CPU power: top gives me From other, similar threads, I took the tip to use mod_status. Aside from HUGE amounts of NULL requests, it gives: CPU Usage: u2.16 s1.32 cu0 cs0 - .0835% CPU load 1.2 requests/sec - 17.6 kB/second - 14.6 kB/request 8 requests currently being processed, 42 idle workers The access and error logs do not show anything surprising or intriguing at all. Note the .8% CPU usage. Another tip was to use strace: root@server:~# strace -p 1956 Process 1956 attached - interrupt to quit restart_syscall(<... resuming interrupted call ...> And remains like this for at least half an hour, without producing any additional output. Restarting apache fixed the problem for less than a second The server runs a few custom python scripts aswell as a django-powered website on apache2 (up-to-date), but even turning the scripts off (or not having them active in the first place) did not change anything. After I stopped apache and powered my server off, powered it on a few minutes afterwards and restarted all my services, the CPU usage remained low for several hours, just in order to pop up again randomly (?) The DigitalOcean CPU stats on my server are: You can see how the CPU usage was super high for almost half a day until I restarted the bot - just to remain stable for several hours and then pop up again. I am completely at a loss of words and don't know what I could do to find out what piece of my code is giving me these problems or if apache itself is the cause... Therefore I would greatly appreciate any hints to the questions: What else can I try to do? Which things might I not have checked? Is this definitely in my own code? How do you find what part of python code crashes an app via a infinite loop or similar?

  Read the article

• HP EliteBook 8440P - USB ports stop working on docking station

  - by r0ca

  I have a HP Elitebook 8440P running Windows XP Pro SP3. I installed it on my docking station and everything went smooth for a while. Last week, my mouse and any other USB devices stoped working sudenly... It was working fine on my laptop itself but nothing on my docking station. LCD attached monitor works and same for LAN and PS2 keyboard. I updated the BIOS, Chipset, Video Drivers, also changed my docking station by a brand new one but the problem still comes back. I also noticed something in Device Manager... A Generic USB Root Hub has an error on it, a Yellow/Orange exclamation mark. I tried to update that driver but no luck. Windows is unable to process it. This seems to be the problem but can't fix it. I may only re-image my laptop but for me, I need to avoid that since I have so many apps installed on it. If anybody has any advice, I'll take it!

  Read the article

• Windows Server 2012 Can't Print

  - by Chris

  I know this may sound incredibly stupid and there is probably an easy solution but I can't seem to find it. Friends of mine recently upgraded their server for their small business from the POS old one. New hardware and a change from Windows Server 2003 to Windows Server 2012. I've got everything they need transfered over and running except for printing. They need to be able to print to printers in the vans their technicians use from the server via remote desktop. In other words the use a laptop to remote desktop into the server and need to print invoices out from the remote server to printers attached locally via usb. On the old server they just installed the identical driver and that was it, they could print as needed. On this server no matter what we seem to do we can't get it to print remotely, and in the process we also discovered that the server can't even print to the network printer. It sees the printer on it's network and it sees (through redirect) the printers in the vans but when you hit print it claims it did and nothing happens. There isn't an issue with the printers themselves as every other device we have can print to them without issues. Is there some setting that is inhibiting the server from printing? Is there something I need to install (print server?) to add the functionality? Thanks in advance for helping me out here

  Read the article

• Accidentally dd'ed an image to wrong drive / overwrote partition table + NTFS partition start

  - by Kento Locatelli

  I screwed up and set the wrong output for dd when trying to copy a freenas iso, overwriting the wrong external hard drive. Ironically, I was trying to setup a freenas server for data backup... External drive is only used for data storage, system is entirely intact Drive had a single NTFS partition filing the entire device (2TB WD elements) Drive originally had an MBR partition table. Drive now shows as having a GPT, presumably from the freenas image. Drive was mounted at the time, with maybe a couple kB of data written/read after running dd Drive is just a few months old and healthy (regular SMART / fs checks) I have not reboot the OS (crunchbang) /proc/partition still holds the correct information (and has been stored) Have dd's output (records in / out / bytes) testdrive did not find any partitions on quick or deep search running photorec to recover the more important data (a couple recent plaintext files that hadn't been backed up yet). Vast majority of disk content ( 80%) is unnecessary media files. My current plan is to let photorec do it's thing, then recreate the mbr with gparted and use cfdisk to create another NTFS partition using the sector information from /sys/block/.../. Is that a good course of action (that is, a chance of success)? Or anything else I should try first? Possibly relevant information: dd if=FreeNAS-8.0.4-RELEASE-p3-x86.iso of=/dev/sdc: 194568+0 records in 194568+0 records out 99618816 bytes (100 MB) copied grep . /sys/block/sdc/sdc*/{start,size}: /sys/block/sdc/sdc1/start:2048 /sys/block/sdc/sdc1/size:3907022848 cat /proc/partitions: major minor #blocks name ** Snipped ** 8 32 1953512448 sdc 8 33 1953511424 sdc1 current fdisk -l output: WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 2000.4 GB, 2000396746752 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table

  Read the article

• sudo fdisk in a live session does not show all hard drives

  - by cornbread

  I am having Grub2 issues in my Ubuntu 10.04 dual boot, 2 hard drive system. So I am attempting to follow the standard grub2 reinstallation guide (cant post link because of spam filters allowing only one... ?_?) Don't know if this is the root of my problem, but my speedy internal HD with my OS on it is not showing up anywhere in a live session. Not in nautilus, behind fdisk.... no where. When I can get the main system to boot, there is no issue seeing all available partitions. But the live session sees only the 1TB internal media/backup hard drive. I need access to the other hard drive and it's partitions to finish the grub2 re-installation but I am not sure anymore that is the underlying issue. Anyone have experience with this? The issue I have identified as a grub2 issue is fully described here. SandPvvr describes it exactly. Some notes: I do not see the grub2 menu for my os's holding down the shift key after my bios screen works maybe 10% of the time Not related to reinstalling a windows os. havent been touched in a year do some web development. issue may have started when I was playing with ruby and django. not sure on this. Could a dev environment do this? fdisk in live session ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0001d518 Device Boot Start End Blocks Id System /dev/sdb2 1 121601 976759939 5 Extended /dev/sdb5 487 110765 885816036 83 Linux /dev/sdb6 110766 121601 87040138+ b W95 FAT32 /dev/sdb7 1 486 3903700+ 82 Linux swap / Solaris Partition table entries are not in disk order

  Read the article

• The Wifi is working fine but no internet connection in Windows 8 [migrated]

  - by Ali

  I'm currently having a Problem with my msi GT70 laptop. my laptop is running windows 8 and yesterday it requested a Restart to Update. after the Restart and the update I tried to surf the net through google chrome, the WiFi connection is perfect but the page I tried to access is not loading at all, after a while it shows failure to load page. I disabled and reenabled the WiFi chip through the device manager but still no internet connection. I uninstalled and reinstalled the drivers, still no internet. I updated the Driver of the wifi, still no internet, I even went to Wifi configuration and tried to change the DNS and reset it back to automatically, still no Luck.. I'm really lost I don't know what to do, I don't want to go deep and play with Laptop DNA "aka: registry file" and screw things up. I really appreciate any help in this matter. thanks in advance. Note: I tried to access many pages but no luck. I even tried Firefox, Opera, even ie still no luck. The internet is working fine on my tablet and cellphone, except for the Laptop.

  Read the article

• How to define nodes from a Hiera file in Puppet?

  - by Pigueiras

  I am using puppet and the puppet network device management module and I am trying to build my custom type. In the built-in type for the routers configuration, you can specify a list of nodes and then the configuration inside that node: node "c2950.domain.com" { Interface { duplex => auto, speed => auto } interface { "FastEthernet 0/1": description => "--> to end-user workstation", mode => access, native_vlan => 1000 # [...] More configuration } What I am trying to do, is to move the manifest declaration of the nodes and the configuration of my custom type to a Hiera file like this one: nodes: - node1 - node2 config_device: node1: custom_parameter: "whatever1" node2: custom_parameter: "whatever2" And then in the manifest iterate over the hiera file creating the nodes with the configuration of each node with something like (I am taking as reference this question in serverfault): class my_class { $nodes = hiera_array('nodes') define hash_extract() { $conf_hash = hiera_hash("config_device") $custom_paramter = $conf_hash[$name] ## TRICK lies in $name variable node $name { my_custom_device { $name: custom_parameter => $device_conf['custom_parameter'] } } } hash_extract{$pdu_names: } } } But for this solution I have two problems, I can not define a node inside a define and I can not parameterize a node name. So, is there any way to declare nodes from a Hiera file with their configuration inside?

  Read the article

• Partition is missing in /dev

  - by haimg

  I'm having a strange problem since I moved from Centos5 to Centos6. I have three disks, first two are used as a RAID1, and third one is a stand-alone backup disk that is not listed in /etc/fstab (it is mounded when needed and then unmounted). My problem: After a boot, /dev/sdc exists but /dev/sdc1 does not. Also, the links in /dev/disks are also absent for the first partition of sdc. Disk itself is fine, and if I hot-remove it and plug it back in, /dev/sdc1 appears ok and everything is working. My question: What subsystem manages auto-discovery of disks, partitions, etc. during the boot process (e.g. what creates /dev/disks/by-label)? How do I configure it to scan /dev/sdc too and create all relevant files and links in /dev ? Edit: Here's the relevant part of dmesg output (the only place sdc appears). It does list sdc1, but it's not in /dev! sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 3:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdc] Write Protect is off sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdc: sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: DMAR:[DMA Read] Request device [00:1e.0] fault addr 361bc000 DMAR:[fault reason 06] PTE Read access is not set sdb1 sdb2 sdb3 sdc1 sda1 sd 1:0:0:0: [sdb] Attached SCSI disk sd 3:0:0:0: [sdc] Attached SCSI disk sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk

  Read the article

• Large, high performance object or key/value store for HTTP serving on Linux

  - by Tommy

  I have a service that serves images to end users at a very high rate using plain HTTP. The images vary between 4 and 64kbytes, and there are 1.300.000.000 of them in total. The dataset is about 30TiB in size and changes (new objects, updates, deletes) make out less than 1% of the requests. The number of requests pr. second vary from 240 to 9000 and is dispersed pretty much all over, with few objects being especially "hot". As of now, these images are files on a ext3 filesystem distributed read only across a large amount of mid range servers. This poses several problems: Using a fileysystem is very inefficient since the metadata size is large, the inode/dentry cache is volatile on linux and some daemons tend to stat()/readdir() it's way through the directory structure, which in my case becomes very expensive. Updating the dataset is very time consuming and requires remounting between set A and B. The only reasonable handling is operating on the block device for backup, copying, etc. What I would like is a deamon that: speaks HTTP (get, put, delete and perhaps update) stores data it in an efficient structure. The index should remain in memory, and considering the amount of objects, the overhead must be small. The software should be able to handle massive connections with slow (if any) time needed to ramp up. Index should be read in memory at startup. Statistics would be nice, but not mandatory. I have experimented a bit with riak, redis, mongodb, kyoto and varnish with persistent storage, but I haven't had the chance to dig in really deep yet.

  Read the article

< Previous Page | 581 582 583 584 585 586 587 588 589 590 591 592  | Next Page >