Search Results

Search found 18209 results on 729 pages for 'loop device'.

Page 582/729 | < Previous Page | 578 579 580 581 582 583 584 585 586 587 588 589  | Next Page >

• Recover data from a Thecus N4100 NAS jbod partition

  - by TimothyP

  I have a Thecus N4100 NAS wich had a 2TB drive in it configured as jbod partition. Later I tried adding a second drive to expand the available space. I added it to the jbod configuration but I did not get any extra space. Then I tried removing the second drive but then the NAS system indicated the jbod configuration was damaged. After a reboot it told me there is no configuration and I need to create a new RAID/jbod configuration and that I would lose all data on the drive. Of course I did not do this, I took the 2TB drive and checked with Linux if the partition was still there and it is... completely intact. I found that linux recognizes it as a /dev/mdX device and that I should be able to mount it but I don't know the file system type. Anyway.... is there a way to recover the data? Since everything has always been on a single drive it should all be there right? I can connect the drive to Windows , Linux or MacOS so whatever gets the job done.

  Read the article

• To what extent is size a factor in SSD performance?

  - by artif

  To what extent is the size of an SSD a factor in its performance? In my mind, correct me if I'm wrong, a bigger SSD should be, everything else being equal, faster than a smaller one. A bigger SSD would have more erase blocks and thus more leeway for the FTL (flash translation layer) to do garbage collection optimization. Also there would be more time before TRIM became necessary. I see on Wikipedia that it remarks that "The performance of the SSD can scale with the number of parallel NAND flash chips used in the device" so it seems throughput also increases significantly. Also many SSDs contain internal caches of some sort and presumably those caches are larger for correspondingly large SSDs. But supposing this effect exists, I would like a quantitative analysis. Does throughput increase linearly? How much is garbage collection impacted, if at all? Does latency stay the same? And so on. Would the performance of a 8 GB SSD be significantly different from, for example, an 80 GB SSD assuming both used high quality chips, controllers, etc? Are there any resources (webpages, research papers, presentations, books, etc) that discuss correlations between SSD performance (4 KB random write speed, latency, maximum sequential throughput, etc) and size? I realize this does not really sound like a programming question but it is relevant for what I'm working on (using flash for caching hard drive data) which does involve programming. If there is a better place to ask this question, eg a more hardware oriented site, what would that be? Something like the equivalent of stack overflow (or perhaps a forum) for in-depth questions on hardware interfaces, internals, etc would be appreciated.

  Read the article

• USB Harddisk not working on dual boot windows7/8

  - by Jesper

  Yesterday I installed Windows 8 on a machine that already had Windows 7. They are on dual boot and both systems work fine. The problem is that inserting a USB hard disk in either system does nothing. If I connect a USB mouse or mobile phone, they work fine, so the USB plugs are active/working and the USB hard drives that I am trying to connect work on my other laptop just fine. I have tried to uninstall all USB-related items in Device Manager and let them reinstall upon restart, but that didn't help. The USB drive does not show up in disk management either. The strange thing is that it is exactly the same situation on both windows. USB mice etc. work just fine and USB hard drives do not. Any ideas on solving this problem would be great. ...Don't know if it is important, but this is a Toshiba Tecra R950 Laptop. EDIT: I have found out that my other USB HD (Western Digital) works on this laptop, but for my StoreJet Transcend and Adata "something" does not work. All three work on another Windows 7 laptop. Sizewise the WD is in the middle at 400 GB. The StoreJet is 640 GB and the Adata is 200 GB.

  Read the article

• Why do I have to log into hotmail twice?

  - by Tony Lee

  I just recently noticed I have to attempt a login into hotmail twice before it succeeds. Although I'm using Google Chrome (3.0.195.21), the symptoms are well described in a Mozilla thread. In short, I'm told: The e-mail address or password is incorrect. Please try again. The thread on mozilla's site that supposed to describe the latest details (and the 1st hit on google when I search for "hotmail login twice") requires an account to read so I'm hoping someone here has a good synopsis of what the cause is. I normally start at hotmail.com, which redirects to login.live.com/.... I can login by starting at mail.live.com, using IE8 or attempting a 2nd login. Oddly, if I start at login.live.com Chrome tells me there is a redirect loop. Does anyone know or have a public link to the root cause of the double login? (it is a hotmail account I'm login into) EDIT - Caused by my 'restricting how 3rd parties can use cookies'. If I allow all cookies, it works first time.

  Read the article

• Is my OCZ SSD aligned correctly? (Linux)

  - by Barney Gumble

  I have an OCZ Agility 2 SSD with 40 GB of space. I use it as a system drive in Debian Linux (Squeeze) and in my opinion it's really fast. But I've read a lot on aligning partitions and file systems... And I'm not sure if I succeeded in aligning the partitions correctly. Maybe the SSD could be even faster?? ;-) I use ext4 and here is the output of fdisk -cul: Disk /dev/sda: 40.0 GB, 40018599936 bytes 255 heads, 63 sectors/track, 4865 cylinders, total 78161328 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: [...] Device Boot Start End Blocks Id System /dev/sda1 * 2048 73242623 36620288 83 Linux /dev/sda2 73244670 78159871 2457601 5 Extended /dev/sda5 73244672 78159871 2457600 82 Linux swap / Solaris My partitions were created just by the Debian Squeeze setup assistant. So I didn't care about the details of partitioning. But now I think maybe the installer didn't align it correctly? Actually, 2048 looks good to me (better than odd values like 63 or something like that) but I've no idea... ;-) Help plz! According to some "SSD Alignment Calculator" I found on the web, the OCZ SSDs have a NAND Erase Block Size of 512kB and their NAND Page Size is 4kB. 2048 is divisible by 4 and 512. So are the partitions aligned correctly?

  Read the article

• Small store infrastructure - where to begin?

  - by KevinM1

  It looks like my older brother is about to change jobs - from lawyer to shooting range proprietor - and since I'm the family 'computer guy' I have the task of coming up with and setting up the in-store equipment. Only problem, I don't know how to start or where to look. I'm a web programmer, not an IT specialist. To that end, I figured I should ask the pros. Users: 3 (myself, my brother, and his business partner) Equipment: 1 Windows (likely 7) desktop for POS software, 1 Windows desktop/laptop for backroom use (bookkeeping, etc.) Other: ?? I'm looking for a reliable and, well, idiot-proof way to handle backups. Neither my brother nor his business partner are tech savvy (A web browser, email, MS Word and Excel are about the extent of their knowledge), so I need something they can handle. On-site would be preferable to off-site, given my brother's hesitance to have sensitive business data be handled by an outside source. I'm also looking for a small on-site server. I estimate that, at most, only 2-3 users will need access. A linux solution would keep costs down, but I'm concerned about Windows <- linux interoperability. Would the store security cameras' storage be handled by the security company, or would we have to stream that data to our own server? I know from my own experience with personal security that the company gives/loans a recording device to the home owner, but I'm not sure about business security. I know this sounds like a shopping list, and it's pretty vague. I wish I could give more detail, but between my own ignorance and things not being 100% nailed down on the business end, I'm a bit stuck. At the very least I'd like a nudge - links on a place to start, what to look for, things I need to think about, etc. - for this endeavor. Thanks.

  Read the article

• Dropped WD External Harddisk, now it's shown as "Not initialized"

  - by Phelios

  So, the WD my passport external harddisk is dropped, and after that, the computer is unable to read it anymore. I was hopping if I can just find another case to try if the harddisk is still readable, but looks like the hard drive itself is not a normal SATA or PATA drive. I think it's modified. So, I can't find another case that I can try on. In the computer, I still can see the drive in the "Disk Management", but it's shown as Uninitialized, no size, and no drive letter. I've also tried a couple of recovery tools. Some can't detect at all, there is one (find and mount software) that can detect but shows 0 size. None of them can recover the data. WD is willing to replace it with a new one, but I still need to recover the data. Any way I can recover the data? UPDATE: I tried initialized it from the windows Disk Manager, but it give error "The request could not be performed because of an I/O device error."

  Read the article

• How to get rid of "Maxback Engine" for good?

  - by Jonik

  I used to have a Maxtor Shared Storage II network drive; it broke down long ago already. (Later I tried to recover some data from it, and partially succeeded, but haven't yet fully documented it on that question.) Anyway, I just noticed there are still some lingering bits remaining of the (thourougly crappy) software that came with the Maxtor device: a background process called "MaxBack Engine". I googled around a bit and found something related but not very useful: http://www.straitmac.com/jforum/posts/list/600.page http://discussions.apple.com/thread.jspa?threadID=725692 Under /Applications I found "Maxtor EasyManage.app" which I used to use for controlling the drive, and showed it some "rm -rf". Before deleting, I noted that the bundle did contain "MaxBack Engine.app" under Content/Resources. But still, after reboot, the "MaxBack Engine" process is back. I did notice though that it only appears when logging in with my usual user account; with another account it wasn't launched. So, dear Mac gurus, what could I do about this pest? I guess I could fall back to some Unix hackery and write a cronjob that kills any process with that name, but obviously it'd be nicer to be able to clean up from my computer everything left behind by Maxtor's piece of software.

  Read the article

• Attaching 3.5" desktop drive to MacBook SATA

  - by Kyle Cronin

  I have a mid-2007 MacBook that, according to the Apple Store, has suffered some liquid damage and requires a new logic board to operate correctly, a ~$750 repair I've been told (would normally be around ~$300 were it not for the "liquid damage"). The unit itself works fine - the only problem I've been having is that the system does not recognize the battery and will not charge it. Curiously, the system can still be powered by the battery and even recognizes when the power cord is detached by diming the backlight, but I digress. Now that this laptop will likely become a desktop, I'm wondering if it might be possible to attach a desktop drive. I recently purchased a 2TB SATA drive and I'm wondering if it's possible to somehow attach it where the current internal drive connects. Obviously the drive itself will not fit inside the device, but as the unit will spend the rest of its days on my desk, that's not really much of an issue. My main questions are: Is this possible? If so, how would I connect the drive? Would a SATA extender cable work? Is the SATA port on my MacBook capable of powering a desktop drive? Or should I just get a SATA male-to-female cable and see if I can power the drive through other means (a cheap power supply, for example) The disk I'm referring to is the Hitachi Deskstar HD32000. Though I couldn't find that exact model on Hitachi's support site, these are the power requirements for a similar drive, the 7K2000 (2TB, 7200RPM, SATA II): Power Requirement +5 VDC (+/-5%) +12 VDC (+/-10%) Startup current (A, max.) 1.2 (+5V), 2.0 (+12V) Idle (W) 7.5 From what I've read, 2.5" drives require 5V, meaning that my MacBook obviously is capable of producing it. The specs seem to suggest that this drive seems capable of accepting it instead of the typical 12V - is this an accurate interpretation of the power requirements? Or does it need both 12V and 5V?

  Read the article

• SSH Interactive mode not working

  - by Ekin Koc

  I have a Debian based linux server running for a year or so, without any problems. A couple of days ago, ssh interactive mode stopped working for no reason. I mean, I can open an ssh connection just fine, the server greets me with shell but I just can't type anything. However, if I send commands like this: ssh [email protected] cat /var/log/messages, I get the response. I dug through several logs and found one message, which feels remotely relevant to the problem; sh kernel: [10222733.062511] ------------[ cut here ]------------ sh kernel: [10222733.062522] WARNING: at /build/buildd-linux-2.6_2.6.32-39-amd64-7yVIH2/linux-2.6-2.6.32/debian/build/source_amd64_none/drivers/char/tty_ldisc.c:738 tty_ldisc_reinit+0x46/0x7b() sh kernel: [10222733.062526] Hardware name: PowerEdge R210 II sh kernel: [10222733.062528] Modules linked in: ipt_MASQUERADE iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack nf_defrag_ipv4 ip_tables x_tables sha1_generic arc4 ecb ppp_mppe ppp_async crc_ccitt ppp_generic slhc loop snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 i2c_core pcspkr evdev joydev dcdbas container button processor ext3 jbd mbcache sg sd_mod sr_mod crc_t10dif cdrom usb_storage usbhid hid mpt2sas ahci ehci_hcd libata scsi_transport_sas usbcore bnx2 nls_base scsi_mod fan thermal thermal_sys [last unloaded: scsi_wait_scan] sh kernel: [10222733.062568] Pid: 8662, comm: sshd Not tainted 2.6.32-5-amd64 #1 sh kernel: [10222733.062569] Call Trace: sh kernel: [10222733.062572] [<ffffffff811ff056>] ? tty_ldisc_reinit+0x46/0x7b sh kernel: [10222733.062574] [<ffffffff811ff056>] ? tty_ldisc_reinit+0x46/0x7b Is there any way to get back the sshd working in interactive mode? I tried restarting sshd but that is no help. And somehow, I can not reboot the server. Tried sending shutdown -r now and reboot but it refuses to go down. Should I go ahead and request a physical reboot?

  Read the article

• I've just set up FreeBSD 8.0 and can't login with ssh

  - by Matt

  /etc/hosts.allow is set to allow any protocol from anywhere. I can "ssh localhost" and it works. I simply get "connection refused" from putty on another machine. Any ideas? Will try to get a copy of the sshd_server.conf file as soon as I can find a flash disk to copy it to, but I thought someone might know what you need to set initially to permit login. EDIT: I think I can see why it's not working now. If I telnet to the IP address of the server I'm seeing MGE UPS SYSTEMS SNMP Web/Agent configuration menu. Enter Password: Doh. Ok, so the IP address is assigned by DHCP, but it seems there is already a device statically assigned to that address. I'll put in a reservation and try again. ok, sorted now. It was an ip address conflict. Windows DHCP isn't smart enough to check if there is something listening on the address before first assigning it.

  Read the article

• Directory tree in a Resource without extraction...

  - by Corelgott

  Hi all, i am looking for a way to store a complete directory including sub directories in an application's resource and not have to extract it to use it. Details: We would like to use GeckoFx (Gecko as C# Component) in one of our applications. GeckoFX needs the XUL-Runner and needs to find it's folder structure We have some other data which I would not prefer to extracted to the customer's pc; At least not onto something persistent like a hdd... Getting the complete directory into the resources is not that kind of a big deal. Compress to one file and done. But not writing it to the disk to use it is something else. I have a strong dislike against temp folders and such things. Would anything like a RAM drive be possible? Some part of the RAM beeing mounted? Does something like this even exist as a lib, or would this only be possible by a device driver? Any thoughts on this? Thanks in advance! Corelgott

  Read the article

• Can MySQL use multiple data directories on different physical storage devices

  - by sirlark

  I am running MySQL with its data dir on a 128Gb SSD. I am dealing with large datasets (~20Gb) that are loaded and processed weekly, each stored in a separate DB for the purposes of time point comparisons. Putting all the data into a single database in unfeasible because the performance on such large databases is already a problem. However, I cannot keep more than 6 datasets on the SSD at a time. Right now I am manually dumping the oldest to much larger 2Tb spinning disk every week, and dropping the database to make space for the new one. But if I need one of the 'archived' databases (a semi regular occurrence) I have to drop a current one (after dumping), reload it, do what I need to, then reverse the results. Is there a way to configure MySQL to use multiple data directories, say one on the SSD and one on the 2Tb spinning disk, and 'merge' them transparently? If I could do this, then archiving would no longer mean "moved out of the database entirely", but instead would mean "moved onto the slow physical device". The time taken to do my queries on a spinning disk would be less than that taken to completely dump, drop, load, drop, reload two entire databases, so this is a win. I thought of using something like unionfs but I can't think of a way to control which database gets stored on which physical drive, because it works by merging on a directory level (from what I understand) so I'm still stuck with using multiple directories. Any help appreciated, thanks in advance

  Read the article

• VLAN ACLs and when to go Layer 3

  - by wuckachucka

  I want to: a) segment several departments into VLANs with the hopes of restricting access between them completely (Sales never needs to talk to Support's workstations or printers and vice-versa) or b) certain IP addresses and TCP/UDP ports across VLANS -- i.e. permitting the Sales VLAN to access the CRM Web Server in the Server VLAN on port 443 only. Port-wise, I'll need a 48-port switch and another 24-port switch to go with the two existing 24-port Layer 2 switches (Linksys); I'm looking at going with D-Links or HP Procurves as Cisco is out of our price range. Question #1: From what I understand (and please correct me if I'm wrong), if the Servers (VLAN10) and Sales (VLAN20) are all on the same 48-port switch (or two stacked 24-port switches), afaik, the switch "knows" what VLANs and ports each device belongs to and will switch packets between them; I can also apply ACLs to restrict access between VLANs at this point. Is this correct? Question #2: Now lets say that Support (VLAN30) is on a different switch (one of the Linksys) switches. I'm assuming I'll need to trunk (tag) switch #2's VLANs across to switch #1, so switch #1 sees switch #2's VLAN30 (and vice-versa). Once Switch #1 can "see" VLAN30, I'm assuming I can then apply ACLs as stated in Question #1. Is this correct? Question #3: Once Switch #1 can see all the VLANs, can I achieve the seemingly "Layer 3" ACL filtering of restricting access to Server VLAN on only certain TCP/UDP ports and IP addresses (say, only permitting 3389 to the Terminal Server, 192.168.10.4/32). I say "seemingly" because some of the Layer 2 switches mention the ability to restrict ports and IP addresses through the ACLs; I (perhaps mistakenly) thought that in order to have Layer 3 ACLs (packet filtering), I'd need to have at least one Layer 3 switch acting as a core router. If my assumptions are incorrect, at which point do you need a Layer 3 switch for inter-VLAN routing vs. inter-VLAN switching? Is it generally only when you need that higher-level packet filtering ability between your departments?

  Read the article

• Setting up virtualbox for outside access

  - by Morgan Green

  I have a computer running a server that my subdomain on my shared hosting account points to. IE subdomain.mydomain.org goes to my home server. Now then; what I'm wanting to do is be able to access my VirtualBox servers through that subdomain and a different port. E.G Ubuntu Virtual Box Server 1 Username:Ubuntuhost1 Password:MyUbuntuHost1 Port:4000 Internal IP: 192.168.1.60 External IP: 24.29.138.45 Ubuntu Virtual Box Server 2 Username:UbuntuHost2 Password:MyUbuntuHost2 Port:4001 Internal IP: 192.168.1.61 External IP: 24.29.138.45 Now I want to be able to access RDP number 1 through Port 4000, but if I access Port 4001 it will connect to the server on port 4001; both using the same subdomain. The next issue is the fact that even though I know what the IP addresses are on the router for the virtualbox hosts through ifconfig it doesn't change the fact that they don't show up on the router. If anyone knows how to configure this to work please help me out because I've been racking my brain to the highest extent I can. Alright; here's an edit to clarify more; Sorry. My ports on the router are edited to forward Port 4000 on Internal IP 192.168.1.63 (My Ubuntu Internal IP address) Now when I go to my Router Home Page my VirtualBox Internal IP Address doesn't show on the attached device listings, so I set up port forwarding anyways to the VirtualBox Internal IP. My end goal is when I connect to mydomain.org and I connect through port 3389 it takes me to my host computers server, but if I put in mydomain.org and go through port 4000 it's going to redirect to my VirtualBox server; Is this even possible? Sorry; I'm trying to clarify the most I think I can I just don't know how else to explain my issue.

  Read the article

• unable to recover data from failed hdd

  - by Eslam Elyamany

  my hdd failing (or maybe totally dead) i've connected the hdd via USB but it doesn't appear in fdisk Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xe9fb38fb Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 40959999 20376576 7 HPFS/NTFS/exFAT /dev/sda4 40962046 976771071 467904513 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 82913280 86910975 1998848 82 Linux swap / Solaris /dev/sda6 86913024 394113023 153600000 7 HPFS/NTFS/exFAT /dev/sda7 40962048 82913279 20975616 83 Linux /dev/sda8 394122708 976768064 291322678+ 7 HPFS/NTFS/exFAT Partition 8 does not start on physical sector boundary. no sdc appears here , BUT it's appears on /dev/ rootghost-lap:/home/ghost# ls /dev/sd* /dev/sda /dev/sda2 /dev/sda5 /dev/sda8 /dev/sdb /dev/sdc1 /dev/sdc2 /dev/sdc6 /dev/sdc8 /dev/sda1 /dev/sda4 /dev/sda6 /dev/sda9 /dev/sdc /dev/sdc10 /dev/sdc5 /dev/sdc7 /dev/sdc9 also it appears in proc Code: rootghost-lap:/home/ghost# cat /proc/partitions major minor #blocks name 8 0 488386584 sda 8 1 102400 sda1 8 2 20376576 sda2 8 4 1 sda4 8 5 1998848 sda5 8 6 153600000 sda6 8 8 291322678 sda8 8 9 20975616 sda9 11 0 1048575 sr0 11 1 99136 sr1 8 32 244198583 sdc 8 33 14651248 sdc1 8 34 1 sdc2 8 37 15380480 sdc5 8 38 4153344 sdc6 8 39 48829536 sdc7 8 40 48829536 sdc8 8 41 110374551 sdc9 8 42 1975963 sdc10 and dmesg : [10604.777168] end_request: I/O error, dev sdc, sector 1 [10604.817238] sd 26:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [10604.817243] sd 26:0:0:0: [sdc] Sense Key : Aborted Command [current] [10604.817248] sd 26:0:0:0: [sdc] Add. Sense: No additional sense information [10604.817253] sd 26:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 02 00 00 06 00 ok now , let's see what i've tried testdisk to check for partitions -- failed dd to copy data from /dev/sdcX -- provide strange output size for example /dev/sdc1 is about 15G , the output for dd is 62G+ so i had to cancle it safecopy successfully made an image for partitons , but can't fix images, can't mount it, can't do any thing with it and some other tools i've tried and all failed , so any idea ?

  Read the article

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• Internet explorer rejects cookies in kerberos protected intranet sites

  - by remix_tj

  I'm trying to build an intranet site using joomla. The webserver is using HTTP Kerberos authentication with mod_kerb_auth. Everything works fine, the users get authenticated and so on. But if i try to login to the administrator panel i can't because IE does not accept the needed cookies. No such problem with firefox. The intranet site is called "intranet_new" and is hosted by webintranet04, under the directory /var/www/vhosts/joomla/intranet_new/. I have my virtualhost for intranet_new containing this: <Location /> AuthType Kerberos AuthName "Kerberos Login" KrbMethodNegotiate On KrbMethodK5Passwd On KrbAuthRealms PROV.TV.LOCAL Krb5KeyTab /etc/apache2/HTTP.keytab require valid-user </Location> The same is for webintranet04 virtualhost, which is the default pointing to /var/www and contains: <Location /vhosts/joomla/> AuthType Kerberos AuthName "Kerberos Login" KrbMethodNegotiate On KrbMethodK5Passwd On KrbAuthRealms PROV.TV.LOCAL Krb5KeyTab /etc/apache2/HTTP.keytab require valid-user </Location> the very strange problem i have is that if i open http:// webintranet04/vhosts/joomla/intranet_new/administrator IE allows me to login, accepting cookie. If i open http:// intranet_new/administrator, instead, i loop on the login page. Last, intranet_new is a CNAME record of webintranet04. This is only an IE problem. I need: - the admin interface to work with IE - the "kerberized" zone to accept cookie, because i am deploying other programs requiring cookies.

  Read the article

• MySQL getting stuck, eating up disk i/o

  - by bonez05

  Hi all, Using mySQL 5.0.51 on Solaris . At intermittent times it looks like MySQL is getting 'stuck' . The disk usage on the server spikes to 98% busy from reads. I used dtrace (specifically DTrace toolkit - iosnoop) to track down what processes was using all the reads. Mysql was calling tablename.TDM hundreds of times per second. There was no more than average load on the webserver that could account for this. There were no cronjobs running, and no other utilities like mysqldump or anything. It is a master / slave replication setup. As a jury-rigged fix, I altered the mysql table from 'tablename' to 'tablename2' and then back to 'tablename' This fixed the problem temporarily, and "unsticks" mysql. The disk usage goes back down and dtrace is no longer showing hundreds of reads to 'tablename.TDM' / second. A couple ideas I had are: 1. MySQL version bug 2. Infinite loop somewhere in my application (which i'm not sure how likely this is) 3. ?? Has anybody seen this before or have any insight? Thanks

  Read the article

• Alternative Bluetooth Stacks for Windows 7 64bit

  - by Martin

  I have a notebook with an inbuilt Broadcom BCM2046 bluetooth adapter and several bluetooth HID-devices (mice, keyboards etc.) The operating system is Windows 7 64 bit Professional. The HID-devices all work perfectly with other computers, but on the system mentionend above, problems with some power-saving features inside the HID-devices occur (see eg. Amazon reviews for Microsoft Mobile Keyboard 6000 not waking up). I have tried the bluetooth drivers supplied by Windows update and the latest Broadcom drivers directly from the Broadcom updater software. The problems persist (I can rule out any further configuration issues or alternative device drivers, I have tried every possibility). I have tried a trial version of the BlueSoleil Bluetooth stack and it solved the wake-up problem. However the BlueSoleil stack causes some other problems, is relatively expensive and I would prefer not to use it. My question: are there any other alternative bluetooth stacks availible for Windows 7 64bit? To my knowledge there used to be Toshiba Bluetooth stack for non-Toshiba hardware, but the older versions I have found on the internet do not install, they do not seem to recognize the bluetooth hardware when installing the driver.

  Read the article

• HP Photosmart C4780 printer/scanner breaks netgear WNDR3700v3 router on connection

  - by CodeJunkie

  A few months ago, we upgraded our Netgear router's firmware. Immediately, we started having trouble connecting to the internet. Each time this problem would happen, every device in the house would stop being able to make new connections to the internet. For example, you couldn't open new pages in the browser, but if Skype was running when the problem happened, you could keep talking to people. The only solution to this problem seemed to be resetting the router to factory defaults. Eventually, we solved this problem by just downgrading the router firmware. A while later, we got a new Netgear router. Almost right away, the new router started having exactly the same problems as the old one did on current firmware. The network connection would stay active and the computer would say it had an internet connection, but you couldn't do anything online except for using Skype. We eventually figured out that this happens every time our HP printer gets onto the network. Any time the printer gets onto the wireless network, the whole network stops connecting to the internet almost completely. The only thing that will fix it at that point is to reset the router to factory specs, and unplug the printer so it can't get back onto the network. The Netgear router has the latest version of the firmware, but the printer/scanner is very old. It looks to me like this problem is probably a result of a firmware conflict between the printer and the router, but I'm not sure how to fix that problem. Here's some additional information: Printer: HP Photosmart C4780 Router: WNDR3700v3 Router firmware: V1.0.0.22_1.0.17 (Stock, up to date firmware) Why would the printer getting on the network cause the router to not be able to access the internet correctly until it was reset? What can be done to allow the printer to be on the network without breaking the network for all other devices? Edit: One other thing that happens during this internet problem is that multiple computers in the house display an "IP conflict" message repeatedly, and extremely frequently (as often as every five to ten minutes, and every time a connection to the wireless is made).

  Read the article

• Winamp playing sound but no video

  - by Greg Sansom

  I am having problems playing video in Winamp (the movie I am trying to play is an AVI - not sure if other formats work). I have installed the K-Lite Codec Pack, and the video does work in Winamp Classic. I can also play the video in Winamp on another machine (although I can't remember the exact configuration details of that machine - and I don't think they're relevant). There are a few symptoms: The content of the Video view is either empty, transparent, or displays rendering from other programs. Opening the Visualization view shows the following error: MILKDROP ERROR DirectX initialization failed (GetDeviceCaps). This means that no valid 3D-accelerated display adapter could be found on your computer. If you know this is not the case, it is possible that your graphics subsystem is unstable; please try rebooting your computer and then try to run the plugin again. Otherwise, please install a 3D-accelerated display adapter. Trying to open streams via the SHOUTCast TV plugin shows Error opening video output, and the video does not open. Opening the file with WMC causes the following error (although the movie still plays): Error creating DX9 allocation presenter CreateDevice failed D3DERR_NOTAVAILABLE There are no warnings displayed in Device Manager, although the display adapter is the standard Windows one. Running DxDiag shows no problems (codec for Video listed as XviD 1.1.2 Final). GSpot reports that codecs are installed. System specs: - Windows Server 2008 r2 Standard 64-bit, with latest updates; - .NET 3.5.1 installed; - Winamp v5.6.01 (latest version); - DirectX 11 (Latest version); - K-Lite Codec Pack 7.0.0 (Full); - Machine is HP DC7600 - full specs here. Please comment if there is any more information which will help to diagnose the problem.

  Read the article

• How to force mdadm to stop RAID5 array?

  - by lucek

  I have /dev/md127 RAID5 array that consisted of four drives. I managed to hot remove them from the array and currently /dev/md127 does not have any drives: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdd1[0] sda1[1] 304052032 blocks super 1.2 [2/2] [UU] md1 : active raid0 sda5[1] sdd5[0] 16770048 blocks super 1.2 512k chunks md127 : active raid5 super 1.2 level 5, 512k chunk, algorithm 2 [4/0] [____] unused devices: <none> and mdadm --detail /dev/md127 /dev/md127: Version : 1.2 Creation Time : Thu Sep 6 10:39:57 2012 Raid Level : raid5 Array Size : 8790402048 (8383.18 GiB 9001.37 GB) Used Dev Size : 2930134016 (2794.39 GiB 3000.46 GB) Raid Devices : 4 Total Devices : 0 Persistence : Superblock is persistent Update Time : Fri Sep 7 17:19:47 2012 State : clean, FAILED Active Devices : 0 Working Devices : 0 Failed Devices : 0 Spare Devices : 0 Layout : left-symmetric Chunk Size : 512K Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 2 0 0 2 removed 3 0 0 3 removed I've tried to do mdadm --stop /dev/md127 but: mdadm --stop /dev/md127 mdadm: Cannot get exclusive access to /dev/md127:Perhaps a running process, mounted filesystem or active volume group? I made sure that it's unmounted, umount -l /dev/md127 and confirmed that it indeed is unmounted: umount /dev/md127 umount: /dev/md127: not mounted I've tried to zero superblock of each drive and I get (for each drive): mdadm --zero-superblock /dev/sde1 mdadm: Unrecognised md component device - /dev/sde1 Here's output of lsof|grep md127: lsof|grep md127 md127_rai 276 root cwd DIR 9,0 4096 2 / md127_rai 276 root rtd DIR 9,0 4096 2 / md127_rai 276 root txt unknown /proc/276/exe What else can I do? LVM is not even installed so it can't be a factor.

  Read the article

• Has anyone else experienced page fault crashes with Snow Leopard on MacBook Pro?

  - by BruceMartin

  I bought a Macbook Pro computer on Sept 3rd from MacMall. As I was using it to learn Snow Leopard (this is my first Mac, I am a long time Windows developer), it would crash every one or two hours. After calling Apple support, I dropped it off at the Apple store for diagnostic testing and repair. WhenI picked up the computer from Apple, they told me that it did not crash while they had it. They suspected a software problem, so they had done a fresh install of Snow Leopard for me. At home I went through the start up procedure with the newly installed Snow Leopard. Then I downloaded the iPhone SDK, and the computer crashed again while I was away waiting for the download to finish. I was using a USB mouse, which was the only device attached. No other software installed. I was presented with a dump that mentions terms like "panic", Kernel trap", and "page fault". Does anyone have any idea what this problem might be? I really can not use this MacBook under these circumstances.

  Read the article

• Connecting multiple access points

  - by mohsen farahanipoor

  I'm working on a big project. We want to create a wireless network throughout the building with 15 floors. My idea is that we should set up one unified wireless access point at least in each floor...in case of signal attenuate, we use Access point extender/repeater. I selected DWL-6600AP from among D-Link industrial access points. I want to implement a single wireless LAN throughout the building. Is it possible to combines multiple DWL-6600 access points to achieving just a single WLAN? Can a wireless switch controller do this task? Can these Access Points interfere with each other? What is the solution? I read D-Link website's learning materials, but I am still confused. My other question is around the connecting these APs to Wireless Switch Controller - Is it possible to use power line for connecting DWL-6600 to Wireless Switch Controller device? My main goal is that clients with portable devices such as laptops should be easily connected to the network to share & have communication without any more manual configuration as they are already connected to a single network.

  Read the article

< Previous Page | 578 579 580 581 582 583 584 585 586 587 588 589  | Next Page >