Search Results

Search found 22139 results on 886 pages for 'security testing'.

Page 705/886 | < Previous Page | 701 702 703 704 705 706 707 708 709 710 711 712  | Next Page >

• Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

  Read the article

• Rapidly changing public IP addresses on certain networks?

  - by zenblender

  I run/develop an online game where many of our users are in southeast asia. I recently went to southeast asia and made an alarming discovery. Anywhere I got internet access, whether it was via 3G, a LAN in a hotel, or wifi in a cafe, both in Singapore and the Philippines, I noticed that my IP address was changing CONSTANTLY. I mean the public IP address, not the private one. I could load a page like whatismyip.com and just hit reload and see a new IP address show up every 5-10 seconds! This has lots of consequences for my online game, as many things "break" if the IP address changes for a given user. Basically, I would like to know more about this. Is there a name for the kind of network or router or paradigm that causes this, so I can read up on it? I don't understand WHY a network would function this way. Does it do this on purpose? Is it for security reasons? Is it to anonymize and protect the identity of the users? Or is it just an "old" method that is mostly obsolete in the rest of the world? Thanks for any info that will help me to understand.

  Read the article

• Opening port 80 in router has no results

  - by Ricardo Pieper

  A friend of mine has a ADSL modem and I need to forward some ports. I have already forwarded the 1521 port (Oracle) and it's working fine. Now I need to forward the port 80. I already set up his IIS bindings to this port, and also forwarded the port like this video shows: https://www.youtube.com/watch?v=DLKD-fyexoo So I think I did everything correctly. The local IP address is also the same as the machine where the IIS server is running. I'm sorry, but I can't post images since i don't have 10 points :( Somehow I can't forward this port, yougetsignal.com keeps saying that the door is closed. When I try to open the port, the Control Panel says me that I have to access the control panel in the 8080 port, because the 80 port will be open. Ok, that's fine. But I'm still able to access it in the 80 port, and when I try to access it in the 8080 port, it doesn't work. I'm trying it with the TPLINK 8816, but I also tried to open it in the Opticom DsLink 279, and it didn't worked (using another machine), I got the exact same results. He has a dynamic IP address, but he is also using No-ip, so I can always access his Oracle database in a certain static address. The 1521 port is open. I also tried to disable the firewall in Windows, but that makes no sense to me, since the router doesn't really open the port 80. Clearly I'm missing something. I have never done it in my life, so I dont know how to proceed. Restarting the router was the first I did, no results. I'm accessing his laptop through TeamViewer, so I'm testing the port outside his local network. Edit: My ISP says that they allow to open ports, and the 1521 port is opened. What could I do to open the 80 port?

  Read the article

• Moving symlinks into a folder based on id3 tags.

  - by Reti

  I'm trying to get my music folder into something sensible. Right now, I have all my music stored in /home/foo so I have all of the albums soft linked to ~/music. I want the structure to be ~/music/<artist>/<album> I've got all of the symlinks into ~/music right now so I just need to get the symlinks into the proper structure. I'm trying to do this by delving into the symlinked album, getting the artist name with id3info. I can do this, but I can't seem to get it to work correctly. for i in $( find -L $i -name "*.mp3" -printf "%h\n") do echo "$i" #testing purposes #find its artist #the stuff after read file just cuts up id3info to get just the artist name #$artist = find -L $i -name "*.mp3" | read file; id3info $file | grep TPE | sed "s|.*: \(.*\)|\1|"|head -n1 #move it to correct artist folder #mv "$i" "$artist" done Now, it does find the correct folder, but every time there is a space in the dir name it makes it a newline. Here's a sample of what I'm trying to do $ ls DJ Exortius/ The Trance Mix 3 Wanderlust - DJ Exortius [TRANCE DEEP VOCAL TECH]@ I'm trying to mv The Trance Mix 3 Wanderlust - DJ Exortius [TRANCE DEEP VOCAL TECH]@ into the real directory DJ Exortius. DJ Exortius already exists, so it's just a matter of moving it into the correct directory that's based on the id3 tag of the mp3 inside. Thanks! PS: I've tried easytag, but when I restructure the album, it moves it from /home/foo which is not what I want.

  Read the article

• When running PowerShell script as a scheduled task some Exchange 2010 database properties are null

  - by barophobia

  Hello, I've written a script that intends to retrieve the DatabaseSize of a database from Exchange 2010. I created a new AD user for this script to run under as a scheduled task. I gave this user admin rights to the Exchange Organization (as a last resort during my testing) and local admin rights on the Exchange machine. When I run this script manually by starting powershell (with runas /noprofile /user:domain\user powershell) everything works fine. All the database properties are available. When I run the script as a scheduled task a lot of the properties are null including the one I want: DatabaseSize. I've also tried running the script as the domain admin account with the same results. There must be something different in the two contexts but I can't figure out what it is. My script: Add-PSSnapin Microsoft.Exchange.Management.PowerShell.E2010 Write-EventLog 'Windows PowerShell' -source PowerShell -eventid 100 -message "Starting script" $databases = get-mailboxdatabase -status if($databases -ne $null) { Write-EventLog 'Windows PowerShell' -source PowerShell -eventid 100 -message "Object created" $databasesize_text = $databases.databasesize.tomb().tostring() if($databasesize_text -ne $null) { $output = "echo "+$databasesize_text+":ok" Write-EventLog 'Windows PowerShell' -source PowerShell -eventid 100 -message "Path check" if(test-path "\\mon-01\prtgsensors\EXE\") { Write-EventLog 'Windows PowerShell' -source PowerShell -eventid 100 -message "Path valid" Set-Content \\mon-01\prtgsensors\EXE\ex-05_db_size.bat -value $output } Write-EventLog 'Windows PowerShell' -source PowerShell -eventid 100 -message "Exiting program" } else { Write-EventLog 'Windows PowerShell' -source PowerShell -eventid 100 -message "databasesize_text is empty. nothing to do" } } else { Write-EventLog 'Windows PowerShell' -source PowerShell -eventid 100 -message "object not created. nothing to do" } exit 0

  Read the article

• Can't connect to MS SQL Server database using SSMS

  - by Charles

  I have a database on line with Godaddy (who uses SQL Server 2005). They provide basic management tools, but tell you that for more advanced tools you can connect directly using SSMS. I followed their instructions to ensure my online database will accept remote connections, and can apparently log in using SSMS with success (after giving my hostname and access data). However: Now from in SSMS, when attempting to expand the "Databases" folder tree, I get the following error: Failed to retrieve data for this request. (Microsoft.SqlServer.Management.Sdk.Sfc) An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.ConnectionInfo) The server principal "cmitchell" is not able to access the database "3pointdb" under the current security context. (Microsoft SQL Server, Error: 916) The irony is that 3pointdb isn't my database. It is just another in a long list of databases that show up when I access my Godaddy backend. From SSMS, I selected the default database to be the name of my database, which it did locate on the list when I browsed. Still same error message. It is trying to connect to a database that isn't mine! :( Godaddy support, after a bit of testing, said the problem isn't on their end. it's on mine. – Charles

  Read the article

• Can't connect to public WiFi with MacBookPro at coffee shops and libraries

  - by Nathan Bowers

  The Problem: I can't connect to public, unencrypted WiFi at my local public library or Peets Coffee. My Setup: Late 2006 MacBookPro running 10.5.8. I have Parallels installed. It's supposed to work like this: 1) Connect to their unencrypted WiFi network 2) Open a browser which redirects you to their "enter password/agree to terms" page. 3) Browse normally. I can connect to the WiFi network, but when I try to authenticate I always get stuck in a redirect loop. It's been like this for a while. Even before I upgraded to 10.5.8. I never have trouble with encrypted networks or regular open WiFi. What I've tried: Disabling Parallels connections in Network Prefs. Superstition: somehow Parallels installed something in the network stack that's messing me up. Pinging the IP address of the WiFi node I'm connected to. I can ping it, it's there, but I still get stuck in this authentication redirect loop. Tried different browsers, tried different cookie and security settings. Even tried IE under Parallels. No dice. Tried flushing DNS cache. Asked library and coffee employees for help. It didn't go well. My Question: Anybody else have this problem? What should I be looking for?

  Read the article

• Adding 2008 Server to 2008 Domain

  - by Phillip

  Hello, I'm trying to create a lab for testing before I deploy solutions, I'm no experienced IT Administrator, and therefore I come here for help. I'm running 2 Virtual Servers on the same machine on a local connection between those two. They'are able to ping each other. Their names is TSDATA1 and TSDATA2 where TSDATA1 is the Domain Controller. I am able to ping between those two, on both "ping TSDATA1" and "ping 10.0.0.1" which is the IP address of TSDATA1. The IP address of TSDATA2 is 10.0.0.2. I'm trying to join the domain with TSDATA2 both I'm getting this error when trying: Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the file C:\Windows\debug\dcdiag.txt. The following error occurred when DNS was queried for the service location (SRV) resource record used to locate an Active Directory Domain Controller for domain tsdata.local: The error was: "DNS name does not exist." (error code 0x0000232B RCODE_NAME_ERROR) The query was for the SRV record for _ldap._tcp.dc._msdcs.tsdata.local Common causes of this error include the following: The DNS SRV records required to locate a AD DC for the domain are not registered in DNS. These records are registered with a DNS server automatically when a AD DC is added to a domain. They are updated by the AD DC at set intervals. This computer is configured to use DNS servers with the following IP addresses: 10.0.0.1 One or more of the following zones do not include delegation to its child zone: tsdata.local local . (the root zone) For information about correcting this problem, click Help. I've figured out it has something to do with DNS lookup, but I have no clue what to do. Can anyone help?

  Read the article

• Windows clients unable to access Samba share on AD joined Linux box every 7 days

  - by Hassle2

  The problem: Every 7 days, 2 Windows Servers are unable to access a SMB/CIFS share. It will start working after a handful of hours. The environment: OpenFiler Linux box joined to 2003 AD Domain Foreground app on Win2003 server access the SMB/CIFS share with windows credentials Another process on Win2008 access the share via SQL Server with windows credentials The Samba version on the Linux box is 3.4.5. Security is set to ADS wbinfo and getent return back expected users and groups Does not look to be a double hop issue as it's always the 2 accounts, regardless of the calling user. There is a DNS entry in both forward and reverse lookup zone for the linux box The linux box's computer object in active directory shows that it was modified around/at the same time that the two clients started failing to access the share Trying to access the share via IP works when by name does not Rebooting the Windows server takes care of it (it's production and only restarted it once) Restarting smbd, winbind, nmbd had no effect Error in samba log for the client in question: smbd/sesssetup.c:342(reply_spnego_kerberos) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! The Question: Does this look like the machine account password is changing (hence the AD object showing the updated modified date) or are the two windows clients unable to request a new ticket that works against this linux box?

  Read the article

• SSH client and Command Prompt replacements Windows look-and-feel

  - by Oddthinking

  The Problem I've worked exclusively in Windows. I can handle that. I've worked exclusively in DOS (a long time ago!). I can handle that. I've worked exclusively in Unix. I can handle that. Right now, I am developing a command-line (python) application on a Windows machine, testing it in a DOS box (i.e. Windows' Command prompt), and then deploying it to Linux, and running it with PuTTY. I cannot handle that. My productivity drops dramatically when CTRL-C cuts in one window (Windows) and kills the process in another (DOS, Linux). My productivity drops dramatically when Enter copies the selection in one window (DOS), and deletes the selection in another (Windows), and runs the current half-edited command in the third (PuTTY). My productivity drops dramatically when I cannot hit Undo, Home or End. The Solution I am Seeking An SSH/Bash command-line client that runs on Windows and, to the extent possible, uses all the standard Windows shortcuts (Cut, Copy, Paste, Undo, Home, End, Insert, Shift-Arrows, etc.) work on a bash command line. Bonus points if it puts the cursor between letters, rather than on them. Plus, an equivalent DOS command-line drop-in that runs on Windows, and provides the same interface. I appreciate there may need to be special buttons to actually transfer CTRL codes (like CTRL-C) through in the cases I need them. I suspect the SSH client will need to be specific to a shell (so it knows when it is at the command prompt, and when it is inside a running app.) I know there are many SSH clients, but I am looking for advice for a particular need. PuTTY feels like an escape route for Unix programmers stuck on Windows. I am the opposite. Can anyone recommend one (or maybe a combination of an SSH client and an Command-Line replacement)?

  Read the article

• java.lang.OutOfMemoryError: unable to create new native thread

  - by Brad

  I consistently get this exception when trying to run my Junit tests on my mac: java.lang.OutOfMemoryError: unable to create new native thread at java.lang.Thread.start0(Native Method) at java.lang.Thread.start(Thread.java:658) at java.util.concurrent.ThreadPoolExecutor.addIfUnderMaximumPoolSize(ThreadPoolExecutor.java:727) at java.util.concurrent.ThreadPoolExecutor.execute(ThreadPoolExecutor.java:657) at java.util.concurrent.AbstractExecutorService.submit(AbstractExecutorService.java:92) at com.google.appengine.tools.development.ApiProxyLocalImpl$PrivilegedApiAction.run(ApiProxyLocalImpl.java:197) at com.google.appengine.tools.development.ApiProxyLocalImpl$PrivilegedApiAction.run(ApiProxyLocalImpl.java:184) at java.security.AccessController.doPrivileged(Native Method) at com.google.appengine.tools.development.ApiProxyLocalImpl.doAsyncCall(ApiProxyLocalImpl.java:172) at com.google.appengine.tools.development.ApiProxyLocalImpl.makeAsyncCall(ApiProxyLocalImpl.java:138) The same set of unit tests pass perfectly fine on ubuntu and windows. Some information about my system resources on the mac: $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited file size (blocks, -f) unlimited max locked memory (kbytes, -l) unlimited max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 1 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 266 virtual memory (kbytes, -v) unlimited $ java -version java version "1.6.0_24" Java(TM) SE Runtime Environment (build 1.6.0_24-b07-334-10M3326) Java HotSpot(TM) 64-Bit Server VM (build 19.1-b02-334, mixed mode) The reason I dont think this is an application issue is because the same tests pass in different environments. I have tried setting heap to 1024m, 512m and setting the stack to 64k and 128k (and each of these combinations) with no luck. My open files was originally 256 and I have bumped this to 1024. I have been googling around for a bit and all posts say to decrease heap size and increase stack size but that doesnt seem to help. Anyone have anymore ideas? EDIT: Here are is some environment information on my ubuntu box: $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 20 file size (blocks, -f) unlimited pending signals (-i) 16382 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) unlimited virtual memory (kbytes, -v) unlimited file locks (-x) unlimited $ java -version java version "1.6.0_24" Java(TM) SE Runtime Environment (build 1.6.0_24-b07) Java HotSpot(TM) 64-Bit Server VM (build 19.1-b02, mixed mode)

  Read the article

• Apache httpd LDAP integration

  - by David W.

  I am configuring a CollabNet Subversion integration. I have the following collabnet_subversion.conf file: <Location /svn> DAV svn SVNParentPath /mnt/svn/new_repos SVNListParentPath on AuthName "VegiBanc Source Repository" AuthType basic AuthzLDAPAuthoritative off AuthBasicProvider ldap AuthLDAPURL ldap://ldap.vegibanc.com/dc=vegibanc,dc=com?sAMAccountName" NONE AuthLDAPBindDN "CN=SVN-Admin,OU=Service Accounts,OU=VegiBanc Users,OU=vegibanc,DC=vegibanc,DC=com" AuthLDAPBindPassword "swordfish" </Location> This works great. Any user in our Active Directory can access our Subversion repository. Now, I want to limit this to only people in the Active Directory group Development: <Location /svn> DAV svn SVNParentPath /mnt/svn/new_repos SVNListParentPath on AuthName "VegiBanc Source Repository" AuthType basic AuthzLDAPAuthoritative off AuthBasicProvider ldap AuthLDAPURL ldap://ldap.vegibanc.com/dc=vegibanc,dc=com?sAMAccountName" NONE AuthLDAPBindDN "CN=SVN-Admin,OU=Service Accounts,OU=VegiBanc Users,OU=VegiBanc,DC=vegibanc,DC=com" AuthLDAPBindPassword "swordfish" Require ldap-group CN=Development OU=Security Groups OU=VegiBanc, dc=vegibanc, dc=com </Location> I added Require ldap-group, but now no one can log in. I have LogLevel set to debug, but all I get is this in my error_log (Single line broken up for easier reading): [Thu Oct 11 13:09:28 2012] [info] [client 10.55.9.45] [6752] vauth_ldap authenticate: user dweintraub authentication failed; URI /svn/ [ldap_search_ext_s() for user failed][Bad search filter] And, I get this in my access_log: 10.55.9.45 - - [11/Oct/2012:13:09:27 -0500] "GET /svn/ HTTP/1.1" 401 401 10.55.9.45 - dweintraub [11/Oct/2012:13:09:28 -0500] "GET /svn/ HTTP/1.1" 500 535 Yes, I am in that group. (Or, at least how can I confirm that just to make sure that's not the issue. I have the SysinternalsSuite ADExplorer. It's where I'm getting all of my info.)

  Read the article

• SQL Server 2005 SP3 on Windows 7 - No Management Studio

  - by Mike Thomas

  I've been trying for a day and a half now to get SQL Server 2005, DEV edition, to work on Windows 7, 64 bit prof. I install from the disk, then run SP 3. I get a failure on the Client Components section of the Installation Progress along with this vague message - Product : Client Components Product Version (Previous): 1399 Product Version (Final) : Status : Failure Log File : C:\Program Files\Microsoft SQL Server\90\Setup Bootstrap\LOG\Hotfix\SQLTools9_Hotfix_KB955706_sqlrun_tools.msp.log Error Number : 1712 Error Description : MSP Error: 1712 One or more of the files required to restore your computer to its previous state could not be found. Restoration will not be possible. I've uninstalled all Visual Studio and tried to make this as clean as possible, and have read a lot of the blog posts, but am really at my wits end about this. I am not a DBA, but I use SQL Server all the time when coding and testing apps. Does anyone have any ideas as to where I can get this sorted out? I've been ati this for a long time and have never encountered an installation as bad as this one. Thanks Mike Thomas

  Read the article

• Linksys router cannot change default password

  - by Jessica M.

  My wireless internet suddenly stopped working today. I have Windows 7 and Lindsys WRT54G router. I tried to log into the Linksys setup router page by typing in www.192.168.1.1 into firefox and it prompted me for a username and password as usual. The problem is when i tried to enter my regular username and password it did not work. I finally solved my problem when I came across this post here and the very last post solved my problem. It suggested I try username: root / password: admin. For some reason the username and password has been changed. When i tried username: root / password: admin , it worked and allowed me to get into the Linksys setup page. The problem is I can't change the username or password anymore. Every time I want to log into my Linksys setup page I have to enter username: root / password: admin. I can't change the "WPA shared key" (password). For the security settings I selected WPA2Personal + AES. Also the post said "If the firmware was upgraded to non-linksys firmware - the default will be different" . The problem is I didn't update anything and I'm worried that someone installed a virus or something or somehow changed the firmware on my router. How did I get non-Linksys firmware on my router? EDIT: I figured out how to change the password when I log into the Lynksys setup page. Administration -- Management -- password. I still don't understand if my router firmware was changed or who changed it or if it happened by mistake.

  Read the article

• Emails sent to outlook.com not being delivered

  - by imukcedup

  I'm having an issue that is a little strange. I have a cPanel webserver that I own and have root. I was testing out emailing and noticed some issues. When I send an email to outlook.com address the email sends ok but nothing is recieved at the outlook mailbox. I also dont get an 'email delivery failure notification' in any mailbox. 2014-06-12 09:53:47 SMTP connection from [127.0.0.1]:45334 (TCP/IP connection count = 1) 2014-06-12 09:53:47 1Wv5Rr-0003rA-2K <= [email protected] H=localhost (ourdomain.com) [127.0.0.1]:45334 P=esmtpa A=dovecot_login:joe S=667 [email protected] T="This is a test message" for [email protected] 2014-06-12 09:53:47 SMTP connection from localhost (ourdomain.com) [127.0.0.1]:45334 closed by QUIT 2014-06-12 09:53:50 cwd=/var/spool/MailScanner/incoming/1029481 5 args: /usr/sbin/exim -C /etc/exim_outgoing.conf -Mc 1Wv5Rr-0003rA-2K 2014-06-12 09:53:50 1Wv5Rr-0003rA-2K SMTP connection outbound 1402581230 1Wv5Rr-0003rA-2K ourdomain.com [email protected] 2014-06-12 09:53:50 1Wv5Rr-0003rA-2K => Test Account <[email protected]> R=archive_outgoing_email T=archiver_outgoing 2014-06-12 09:53:52 1Wv5Rr-0003rA-2K => [email protected] R=dkim_lookuphost T=dkim_remote_smtp H=mx1.hotmail.com [65.54.188.110] X=UNKNOWN:AES128-SHA256:128 C="250 <[email protected]> Queued mail for delivery" 2014-06-12 09:53:52 1Wv5Rr-0003rA-2K Completed I have checked the outlook.com's spam folders and its not in there either. This is a new IP address allocation from our ISP and there was a block on gmail addresses, so we know it was used for spam. But with gmail we got a notifaction of failure and I know outlook/microsoft also send out notification. Does anyone know what could be happening here? Thanks

  Read the article

• Windows 7 network performance tuning for LAN

  - by Hubert Kario

  I want to tune Windows 7 TCP stack for speed in a LAN environment. Bit of background info: I've got a Citrix XenServer set up with Windows 2008R2, Windows 7 and Debian Lenny with Citrix kernel, Windows machines have Tools installed the iperf server process is running on different host, also Debian Lenny. The servers are otherwise idle, tests were repeated few times to confirm results. While testing with iperf 2008R2 can achieve around 600-700Mbps with no tuning what so ever but I can't find any guide or set of parameters that will make Windows 7 achieve anything over 150Mbps with no change in TCP window size using -w parameter to iperf. I tried using netsh autotuining to disabled, experimental, normal and highlyrestricted - no change. Changing congestionprovider doesn't do anything, just as rss and chimney. Setting all the available settings to same values as on Windows 2008R2 host doesn't help. To summarize: Windows 2008R2 default settings: 600-700Mbps Debian, default settings: 600Mbps Windows 7 default settings: 120Mbps Windows 7 default, iperf -w 65536: 400-500Mbps While the missing 400Mbps in performance I blame on crappy Realtek NIC in the XenServer host (I can do ~980Mbps from my laptop to the iperf server) it doesn't explain why Windows 7 can't achieve good performance without manually tuning window size at the application level. So, how to tune Windows 7?

  Read the article

• Determining a realistic measure of requests per second for a web server

  - by Don

  I'm setting up a nginx stack and optimizing the configuration before going live. Running ab to stress test the machine, I was disappointed to see things topping out at 150 requests per second with a significant number of requests taking 1 second to return. Oddly, the machine itself wasn't even breathing hard. I finally thought to ping the box and saw ping times around 100-125 ms. (The machine, to my surprise, is across the country). So, it seems like network latency is dominating my testing. Running the same tests from a machine on the same network as the server (ping times < 1ms) and I see 5000 requests per second, which is more in-line with what I expected from the machine. But this got me thinking: How do I determine and report a "realistic" measure of requests per second for a web server? You always see claims about performance, but shouldn't network latency be taken into consideration? Sure I can serve 5000 request per second to a machine next to the server, but not to a machine across the country. If I have a lot of slow connections, they will eventually impact my server's performance, right? Or am I thinking about this all wrong? Forgive me if this is network engineering 101 stuff. I'm a developer by trade. Update: Edited for clarity.

  Read the article

• VPN being blocked somewhere between either my BT2700HGV and DLink DFL-210

  - by Dom

  Hi, For some time I have been unable to get VPN working through my set up. I have a BT2700HGV Router (2 Wire Model) and as a firewall I have the Dlink DFL-210. You can't turn the firewall completely off on the BT2700HGV so I have it set to DMZplus mode for the Firewall. In theory this should then allow the VPN ports through. On the Firewall I have a series of rules set up and one is the pptp-allow rule which should allow access on the correct ports also. When I try to connect via VPN however the client machine gets an error 809. If I check the log on the Dlink firewall, I see this record: http://dl.dropbox.com/u/1041315/packetdrop.PNG The laptop I am testing the vpn with is connected directly to the BT2700HGV router and I am trying to VPN from it onto 81.138.86.217. I can't work out whether I have some sort of problem in the set up of the rules on my firewall or if the BT router (even though it's in DMZplus mode) is still blocking port 1723. I read somewhere that there where problems because BTs Openzone held onto this port for some reason. Any help would be greatly appreciated. If you need further screen shots or information then please let me know. I wasn't able to create new tags for the router and firewall name or insert the picture in as I am new to the forum. Dom :-)

  Read the article

• Exchange 2003 ActiveSync problem

  - by colemanm

  We're having problems getting iPhones to sync properly with SBS 2003 Exchange. When you add a new Exchange ActiveSync account on an iPhone and enter all the pertinent information, it shows a "Verifying Exchange account info" message for a minute or so, then says everything's verified and asks what you want to sync, Mail, Contacts, Calendars... so it looks like it's working. However, when you go to the Mail app and select the Exchange email account, it just shows an "Inbox" folder with nothing in it. When you try refreshing, it attempts for a second, then says "Last Updated" with a timestamp, as if it worked, but there's no mail and no error message/feedback at all. I think I've narrowed it down to some sort of certificate issue, but I'm having trouble finding out where to go from here... I ran MS's Exchange connectivity testing tool with these results: Our cert was purchased from Network Solutions, and I'd already added it to the IIS Default Website for OWA purposes. But this report makes it look like the cert is somehow problematic. I don't know what to do now... Here's a shot of the cert details, just in case:

  Read the article

• Routing a single request through multiple nginx backend apps

  - by Jonathan Oliver

  I wanted to get an idea if anything like the following scenario was possible: Nginx handles a request and routes it to some kind of authentication application where cookies and/or other kinds of security identifiers are interpreted and verified. The app perhaps makes a few additions to the request (appending authenticated headers). Failing authentication returns an HTTP 401. Nginx then takes the request and routes it through an authorization application which determines, based upon identity and the HTTP verb (put, delete, get, etc.) and URL in question, whether the actor/agent/user has permission to performed the intended action. Perhaps the authorization application modifies the request somewhat by appending another header, for example. Failing authorization returns 403. (Wash, rinse, repeat the proxy pattern for any number of services that want to participate in the request in some fashion.) Finally, Nginx routes the request into the actual application code where the request is inspected and the requested operations are executed according to the URL in question and where the identity of the user can be captured and understood by the application by looking at the altered HTTP request. Ideally, Nginx could do this natively or with a plugin. Any ideas? The alternative that I've considered is having Nginx hand off the initial request to the authentication application and then have this application proxy the request back through to Nginx (whether on the same box or another box). I know there are a number of applications frameworks (Django, RoR, etc.) that can do a lot of this stuff "in process", but I was trying to make things a little more generic and self contained where different applications could "hook" the HTTP pipeline of Nginx and then participate in, short circuit, and even modify the request accordingly. If Nginx can't do this, is anyone aware of other web servers that will perform in the manner described above?

  Read the article

• Have an Input/output error when connecting to a server via ssh

  - by Shehzad009

  Hello I seem to be having a problem while connecting to a Ubuntu Server while connecting via ssh. When I login, I get this error. Could not chdir to home directory /home/username: Input/output error It seems like my home folder is corrupt or something. I cannot ls in the home folder directory, and in my usename directory, I can't cd into this. As root I cannot ls in the home directory as well or in any directory in Home. I notice as well when I save in vim or quit, it get this error at the bottom of the page E138: Cannot write viminfo file /home/root/.viminfo! Any ideas? EDIT: this is what happens if I type in these commands mount proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) fusectl on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) /dev/mapper/RAID1-lvvar on /var type xfs (rw) /dev/mapper/RAID5-lvsrv on /srv type xfs (rw) /dev/mapper/RAID5-lvhome on /home type xfs (rw) /dev/mapper/RAID1-lvtmp on /tmp type reiserfs (rw) dmesg | tail [1213273.364040] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213274.084081] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213309.364038] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213310.084041] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213345.364039] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213346.084042] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213381.365036] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213382.084047] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213417.364039] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213418.084063] Filesystem "dm-4": xfs_log_force: error 5 returned. fdisk -l /dev/sda Cannot open /dev/sda

  Read the article

• Current wisdom on SQL Server and Hyperthreading?

  - by BradC

  Lots of articles out there (see Slava Oks's original SQL 2000 article and Kevin Kline's SQL 2005 update) recommend disabling hyperthreading on SQL servers, or at least testing your specific workload before enabling it on your servers. This issue is gradually becoming less relevant as true multi-core processors replace hyperthreaded ones, but what's the current wisdom on this issue? Does this advice change any with SQL 2005 64-bit, or SQL 2008, or Windows Server 2008? Ideally, this should be tested in advance in a staging environment, but what about for servers that have already made it into production with HT enabled? How can I tell if performance issues we're experiencing might be related to HT? Is there some specific combination of perfmon counters that might point me in that direction, as opposed to all the other things I normally pursue when working on improving SQL performance? Edit: This is especially attractive because of the potential for an across the board improvement for some of my high-cpu servers, but the client is going to want to see something concrete that helps me identify which servers really could benefit from disabling hyperthreading. Of course, conventional performance troubleshooting is ongoing, but sometimes any little bit helps.

  Read the article

• Git push over http (using git-http-backend) and Apache is not working

  - by Ole_Brun

  I have desperately been trying to get push for git working through the "smart-http" mode using git-http-backend. However after many hours of testing and troubleshooting, I am still left with error: Cannot access URL http://localhost/git/hello.git/, return code 22 fatal: git-http-push failed` I am using latest versions of Ubuntu (12.04), Apache2 (2.2.22) and Git (1.7.9.5) and have followed different tutorials found on the Internet, like this one http://www.parallelsymmetry.com/howto/git.jsp. My VHost file currently looks like this: <VirtualHost *:80> SetEnv GIT_PROJECT_ROOT /var/www/git SetEnv GIT_HTTP_EXPORT_ALL SetEnv REMOTE_USER=$REDIRECT_REMOTE_USER DocumentRoot /var/www/git ScriptAliasMatch \ "(?x)^/(.*?)\.git/(HEAD | \ info/refs | \ objects/info/[^/]+ | \ git-(upload|receive)-pack)$" \ /usr/lib/git-core/git-http-backend/$1/$2 <Directory /var/www/git> Options +ExecCGI +SymLinksIfOwnerMatch -MultiViews AllowOverride None Order allow,deny allow from all </Directory> </VirtualHost> I have changed the ownership of the /var/www/git folder to root.www-data and for my test repositories I have enabled anonymous push by doing git config http.receivepack true. I have also tried with authenticated users but with the same outcome. The repositories were created using: sudo git init --bare --shared [repo-name] While looking at the apache2 access.log, it appears to me that WebDAV is trying to be used, and that git-http-backend is never fired: 127.0.0.1 - - [20/May/2012:23:04:53 +0200] "GET /git/hello.git/info/refs?service=git-receive-pack HTTP/1.1" 200 207 "-" "git/1.7.9.5" 127.0.0.1 - - [20/May/2012:23:04:53 +0200] "GET /git/hello.git/HEAD HTTP/1.1" 200 232 "-" "git/1.7.9.5" 127.0.0.1 - - [20/May/2012:23:04:53 +0200] "PROPFIND /git/hello.git/ HTTP/1.1" 405 563 "-" "git/1.7.9.5" What am I doing wrong? Is it an issue with the version of git and/or apache that I am using perhaps? BTW: I have read all the git http related questions on ServerFault and StackOverflow, and none of them provided me with a solution, so please don't mark this as duplicate.

  Read the article

• Windows 7 Loading Very Slow

  - by Adnan

  Hi guys, I've had a problem that only started to occur yesterday. When I boot into Windows 7 and log on to my user account, the computer gets very laggy and slow for at least 5 minutes. Icons take ages to load, and everything is rendered unclickable. This happens for about five minutes after which everything goes back to normal. I tried restarting a few times to see if this is a recurring problem, and it is. I ran a full system scan with Microsoft Security Essentials and found nothing wrong, and I also defragmented the disk to increase performance. However, the problem still exists. Edit: For the past day, I've been trying to install Ubuntu on the same laptop. When installing it on a partition didn't work, I decided to use Wubi. Could this somehow be the problem? Also, my hard drive gets hot a lot, so could the heat be affecting the hard drive and maybe making it defective? Any help on this issue would be greatly, greatly appreciated.

  Read the article

• Missing Data on VMWare Virtual Disk

  - by Lachlan McDonald

  Evening all, I've got a considerable problem I'm hoping to get some resolution on. I had two VMWare 6.5 virtual machines, one running Ubuntu 9.10 and the other Ubuntu 10.04. I used 9.10 as a testing server, so I could install a LAMP environment to prepare some code. Over the months I took a number of snapshots of this VM just in case something went wrong, and did a full copy of the entire VM a month ago. I created the 10.04 VM when Lucid Lynx launched so I could continue development on a fresh install. To get the files over, I simply added the 9.10 virtual disk into the 10.04 VM, grabbed some of the files I needed, and dismounted it. Unknown to me at the time, the changes to the 9.04 virtual disk meant that I could no longer boot it with the 9.10 VM. I'd always get the "The parent virtual disk has been modified since the child was created." error. I decided this was a good time to backup all the critical files, but now whenever I open the 9.04 disk to get the data it isn't in the same state as it was earlier. My question is; is it possible when I'm mounting the virtual disk that I'm not seeing the most recent snapshot, or in my blundering, have I lost the virtual disk. Cheers

  Read the article

< Previous Page | 701 702 703 704 705 706 707 708 709 710 711 712  | Next Page >