Search Results

Search found 49554 results on 1983 pages for 'database users'.

Page 734/1983 | < Previous Page | 730 731 732 733 734 735 736 737 738 739 740 741  | Next Page >

• Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

  - by Srekel

  I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either. EDIT: Adding arp output: C:\Users\Srekel>arp -a Interface: 192.168.1.7 --- 0xd Internet Address Physical Address Type 192.168.1.1 00-1f-33-ef-28-01 dynamic 192.168.1.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Adding ipconfig... C:\Users\Srekel>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Kakburken4 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TP-LINK Wireless N Adapter Physical Address. . . . . . . . . : 00-25-86-DF-C6-89 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 09 April 2010 23:09:45 Lease Expires . . . . . . . . . . : 10 April 2010 23:09:45 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller #2 Physical Address. . . . . . . . . : E0-CB-4E-26-B9-84 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : E0-CB-4E-26-BE-94 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{74D5C406-894E-4000-8DE7-6AAEBF7C8382}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2001:0:5ef5:73ba:881:20c1:3f57:fef8(Preferred) Link-local IPv6 Address . . . . . : fe80::881:20c1:3f57:fef8%14(Preferred) Default Gateway . . . . . . . . . : :: NetBIOS over Tcpip. . . . . . . . : Disabled

  Read the article

• opennms postgres connection slow

  - by krisdigitx

  i am running the opennms application server on a physical server and the database on an ESXi VM. Recently the opennms webconsole has been very slow to load as such i deleted most of the events from the database table, now both servers have no load at all, and the psql connection from the application server to the database server is also very fast, but somehow opennms webconsole is still slow. this is the strace from the opennms process id: 18629 futex(0x2aaac77d8a84, FUTEX_WAIT_PRIVATE, 453, NULL <unfinished ...> 3015 futex(0x2aaabc4a2ee4, FUTEX_WAIT_PRIVATE, 323, NULL <unfinished ...> 10863 futex(0x2aaabbebaa94, FUTEX_WAIT_PRIVATE, 395, NULL <unfinished ...> 25260 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 10859 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 10982 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 3011 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 25260 futex(0x2aaae098fc28, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 10982 futex(0x2aaac0eaf928, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 3011 futex(0x2aaab0cb1728, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 10859 futex(0x2aaac062c328, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 25260 <... futex resumed> ) = 0 10982 <... futex resumed> ) = 0 3011 <... futex resumed> ) = 0 10859 <... futex resumed> ) = 0 25260 futex(0x2aaabc38b6b4, FUTEX_WAIT_PRIVATE, 443, NULL <unfinished ...> 10982 futex(0x2aaabc5d7b94, FUTEX_WAIT_PRIVATE, 99, NULL <unfinished ...> 3011 futex(0x2aaac7c55334, FUTEX_WAIT_PRIVATE, 183, NULL <unfinished ...> 10859 futex(0x2aaabbb8c9d4, FUTEX_WAIT_PRIVATE, 347, NULL <unfinished ...> 10846 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 10846 futex(0x2aaae9022428, FUTEX_WAKE_PRIVATE, 1) = 0 10846 futex(0x2aaabe0030b4, FUTEX_WAIT_PRIVATE, 251, NULL <unfinished ...> 20281 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 14100 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 2925 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 10843 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 20281 futex(0x2aaac7e93628, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 14100 futex(0x2aaac04e8c28, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 2925 futex(0x2aaaec085528, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 10843 futex(0x2aaab20b0528, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> and shows lots of connection timeout??? i think its the connection between the java application and database which is causing issues. any ideas how to troubleshoot this???

  Read the article

• Long connection times from PHP to MySQL on EC2

  - by Erik Giberti

  I'm having an intermittent issue connecting to a database slave with InnoDB. Intermittently I get connections taking longer than 2 seconds. These servers are hosted on Amazon's EC2. The app server is PHP 5.2/Apache running on Ubuntu. The DB slave is running Percona's XtraDB 5.1 on Ubuntu 9.10. It's using an EBS Raid array for the data storage. We already use skip name resolve and bind to address 0.0.0.0. This is a stub of the PHP code that's failing $tmp = mysqli_init(); $start_time = microtime(true); $tmp-options(MYSQLI_OPT_CONNECT_TIMEOUT, 2); $tmp-real_connect($DB_SERVERS[$server]['server'], $DB_SERVERS[$server]['username'], $DB_SERVERS[$server]['password'], $DB_SERVERS[$server]['schema'], $DB_SERVERS[$server]['port']); if(mysqli_connect_errno()){ $timer = microtime(true) - $start_time; mail($errors_to,'DB connection error',$timer); } There's more than 300Mb available on the DB server for new connections and the server is nowhere near the max allowed (60 of 1,200). Loading on both servers is < 2 on 4 core m1.xlarge instances. Some highlights from the mysql config max_connections = 1200 thread_stack = 512K thread_cache_size = 1024 thread_concurrency = 16 innodb-file-per-table innodb_additional_mem_pool_size = 16M innodb_buffer_pool_size = 13G Any help on tracing the source of the slowdown is appreciated. [EDIT] I have been updating the sysctl values for the network but they don't seem to be fixing the problem. I made the following adjustments on both the database and application servers. net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_sack = 0 net.ipv4.tcp_timestamps = 0 net.ipv4.tcp_fin_timeout = 20 net.ipv4.tcp_keepalive_time = 180 net.ipv4.tcp_max_syn_backlog = 1280 net.ipv4.tcp_synack_retries = 1 net.core.rmem_max = 16777216 net.core.wmem_max = 16777216 net.ipv4.tcp_rmem = 4096 87380 16777216 net.ipv4.tcp_wmem = 4096 87380 16777216 [EDIT] Per jaimieb's suggestion, I added some tracing and captured the following data using time. This server handles about 51 queries/second at this the time of day. The connection error was raised once (at 13:06:36) during the 3 minute window outlined below. Since there was 1 failure and roughly 9,200 successful connections, I think this isn't going to produce anything meaningful in terms of reporting. Script: date /root/database_server.txt (time mysql -h database_Server -D schema_name -u appuser -p apppassword -e '') /dev/null 2 /root/database_server.txt Results: === Application Server 1 === Mon Feb 22 13:05:01 EST 2010 real 0m0.008s user 0m0.001s sys 0m0.000s Mon Feb 22 13:06:01 EST 2010 real 0m0.007s user 0m0.002s sys 0m0.000s Mon Feb 22 13:07:01 EST 2010 real 0m0.008s user 0m0.000s sys 0m0.001s === Application Server 2 === Mon Feb 22 13:05:01 EST 2010 real 0m0.009s user 0m0.000s sys 0m0.002s Mon Feb 22 13:06:01 EST 2010 real 0m0.009s user 0m0.001s sys 0m0.003s Mon Feb 22 13:07:01 EST 2010 real 0m0.008s user 0m0.000s sys 0m0.001s === Database Server === Mon Feb 22 13:05:01 EST 2010 real 0m0.016s user 0m0.000s sys 0m0.010s Mon Feb 22 13:06:01 EST 2010 real 0m0.006s user 0m0.010s sys 0m0.000s Mon Feb 22 13:07:01 EST 2010 real 0m0.016s user 0m0.000s sys 0m0.010s [EDIT] Per a suggestion received on a LinkedIn question, I tried setting the back_log value higher. We had been running the default value (50) and increased it to 150. We also raised the kernel value /proc/sys/net/core/somaxconn (maximum socket connections) to 256 on both the application and database server from the default 128. We did see some elevation in processor utilization as a result but still received connection timeouts.

  Read the article

• Issues Converting Plain Text Into Microsoft Word Bulleted Lists

  - by user787832

  I'm a programmer. I hate status reports. I found a way to live with it. While I am working in my IDE ( Visual Slickedit ) I keep a plain text file open in one of the file/buffer tabs. As I finish things I just jot down a quick note into that file. At the end of the week that becomes my weekly status report. Example entries: The Datatables.net plugin runs very slowly in IE 8 with more than 2,000 records. I changed the way I did the server side code to process the data to make less work for the plugin to get decent performance for the IE 8 users. I made a class to wrap data from the new data collection objects into the legacy data holder objects. This will let the new database code be backward compatible with the legacy code until we can replace it. I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site At the end of the month I go back to each weekly *.txt file and paste all of the entries into a MS Word file for a monthly report. I give the monthly report to a liason to the contracting company who has to compile everyone's monthly reports into a single MS Word 2007 document. His problem, soon to be my problem, comes when he highlights my paragraphs like the ones above to put bullets in front of my paragraphs. When he highlights my notes to put bullets in front of them with MS Word 2007, Word rearranges the text a bit and the new line chars/carriage returns stagger the text so the text is no longer in neat chunks. This: I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site Becomes This: I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site I tried turning word wrap on in my IDE for the text files I put my status notes in. It just puts some kind of newline character in anyway. Searching/Replacing those chars in the text files has the result of destroying the paragraphs. Once my notes are pasted into MS Word, Word automatically translates them into paragraph breaks. Searching/Replacing them there has similar results. Blank lines separating the notes disappears. One big mess. What I would like is to be able to keep adding my status notes to a text file as I am now, but do something different when I paste the notes into MS Word such that my liason can select the text, hit the bulleting command and NOT have the staggered text as shown above. Any ideas? Thanks much in advance Steve

  Read the article

• ASP.NET MVC - HttpPost to ReturnURL after redirect

  - by JP

  Hello, I am writing an ASP.NET MVC 2.0 application which requires users to log in before placing a bid on an item. I am using an actionfilter to ensure that the user is logged in and, if not, send them to a login page and set the return url. Below is the code i use in my action filter. if (!filterContext.HttpContext.User.Identity.IsAuthenticated) { filterContext.Result = new RedirectResult(String.Concat("~/Account/LogOn","?ReturnUrl=",filterContext.HttpContext.Request.RawUrl)); return; } In my logon controller I validate the users credentials then sign them in and redirect to the return url FormsAuth.SignIn(userName, rememberMe); if (!String.IsNullOrEmpty(returnUrl)) { return Redirect(returnUrl); } My problem is that this will always use a Get (HttpGet) request whereas my original submission was a post (HttpPost) and should always be a post. Can anyone suggest a way of passing this URL including the HttpMethod or any workaround to ensure that the correct HttpMethod is used? Thanks in advance, JP

  Read the article

• facebook application using iframe on Facebook Developer Toolkit 3.0

  - by adveb

  hey i am trying to build facebook iframe application using the Facebook Developer Toolkit 3.01 asp.net c#. i am working by the ifrmae sample of the toolkit can be download here. www.facebooktoolkit.codeplex.com/releases/view/39727 this is my facebook application that is the same as the iframe sample. http://apps.facebook.com/alefbet/ this is my code, it has 2 pages, master page and default. this 2 pages are the same as the iframe sample. 1) this is the master page. public partial class IFrameMaster : Facebook.Web.CanvasIFrameMasterPage { public IFrameMaster() { RequireLogin = true; } } 2) this is the default.aspx public partial class Default : System.Web.UI.Page { private const string SCRIPT_BLOCK_NAME = "dynamicScript"; protected void Page_Load(object sender, EventArgs e) { if (IsPostBack) { if (Master.Api.Users.HasAppPermission(Enums.ExtendedPermissions.email)) { SendThankYouEmail(); } Response.Redirect("ThankYou.aspx"); } else { if (Master.Api.Users.HasAppPermission(Enums.ExtendedPermissions.email)) { emailPermissionPanel.Visible = false; } CreateScript(); } } private void SendThankYouEmail() { var subject = "Thank you for telling us your favorite color"; var body = "Thank you for telling us what your favorite color is. We hope you have enjoyed using this application. Encourage your friends to tell us their favorite color as well!"; this.Master.Api.Notifications.SendEmail(this.Master.Api.Session.UserId.ToString(), subject, body, string.Empty); } private void CreateScript() { var saveColorScript = @" function saveColor(color) { document.getElementById('" + colorInput.ClientID + @"').value = color; } function submitForm() { document.getElementById('" + form.ClientID + @"').submit(); } "; if (!ClientScript.IsClientScriptBlockRegistered(SCRIPT_BLOCK_NAME)) { ClientScript.RegisterClientScriptBlock(this.GetType(), SCRIPT_BLOCK_NAME, saveColorScript); } } } my directory structure is 1)the master page is in the root. 2)the default.aspx is in the root/alfbet directory. 3)i have also have the xd_receiver.htm inside root/channel directory. that inside the master page their is the folowing line: <script type="text/javascript"> FB_RequireFeatures(["XFBML"], function() { FB.Facebook.init("c81f17ee4d4ffc5113c55f8b99fdcab5", "channel/xd_receiver.htm"); }); </script> the problem is that the applicatin dosent work apps.facebook.com/alefbet/default.aspx why it dosent work ? please help me and others who also obstacle in this issue. i tryied lots of things, one of them was to display the user id. for that i put label in the default.aspx and wrote lblTest.Text = Master.Api.Users.GetInfo().uid.ToString(); and it dosent event get to this line. i know it because it keeps display in the label.text the word "label" thank you very much.

  Read the article

• SqlCeException: The column cannot be modified. [ Column name = id ]

  - by pek

  I am simply trying to add a single row in the database but I keep getting an exception. I created a local database and added a single table: users. It consists of two columns: "id" and "name". I only made the id primary key (not auto-increment or anything else). When I run the following code: string execPath = Path.GetDirectoryName(Assembly.GetExecutingAssembly().GetName().CodeBase); string dbfile = execPath + @"\LocalDatabase.sdf"; SqlCeConnection conn = new SqlCeConnection("datasource=" + dbfile); conn.Open(); string command = "INSERT INTO users VALUES('1','pek')"; Debug.WriteLine(command); SqlCeCommand comm = conn.CreateCommand(); comm.CommandText = command; comm.ExecuteNonQuery(); I get the following Exception at "comm.ExecuteNonQuery();": SqlCeException was unhandled The column cannot be modified. [ Column name = id ] What's with the "modified" part?

  Read the article

• IIS 6.0 Server Too Busy HTTP 503 Connection_Dropped DefaultAppPool

  - by Shiraz Bhaiji

  We have a site which is running on a windows 2003 cluster with 2 64bit machines. The site needs to be able to cope with over 20,000 concurrent users One of the things that the site does is to allow the download of a 2MB file (which is cached in memory). We have low CPU and memory usage. We also have surplus bandwidth. It appears that we are running out of connections due the time it takes the user to download the file (some users have slow internet connections). In the IIS log we get HTTP 503 errors. In the HTTPErr log we get mainly Connection_Dropped DefaultAppPool with some Timer_EntityBody DefaultAppPool. Question is: How can we configure IIS to allow more connections? Or is there something that I am missing here? Thanks Shiraz

  Read the article

• Creating an ASP.NET report using Visual Studio 2010 - Part 1

  - by rajbk

  This tutorial walks you through creating an report based on the Northwind sample database. You will add a client report definition file (RDLC), create a dataset for the RDLC, define queries using LINQ to Entities, design the report and add a ReportViewer web control to render the report in a ASP.NET web page. The report will have a chart control. Different results will be generated by changing filter criteria. At the end of the walkthrough, you should have a UI like the following.  From the UI below, a user is able to view the product list and can see a chart with the sum of Unit price for a given category. They can filter by Category and Supplier. The drop downs will auto post back when the selection is changed.  This demo uses Visual Studio 2010 RTM. This post is split into three parts. The last part has the sample code attached. Creating an ASP.NET report using Visual Studio 2010 - Part 2 Creating an ASP.NET report using Visual Studio 2010 - Part 3   Lets start by creating a new ASP.NET empty web application called “NorthwindReports” Creating the Data Access Layer (DAL) Add a web form called index.aspx to the root directory. You do this by right clicking on the NorthwindReports web project and selecting “Add item..” . Create a folder called “DAL”. We will store all our data access methods and any data transfer objects in here.   Right click on the DAL folder and add a ADO.NET Entity data model called Northwind. Select “Generate from database” and click Next. Create a connection to your database containing the Northwind sample database and click Next.   From the table list, select Categories, Products and Suppliers and click next. Our Entity data model gets created and looks like this:    Adding data transfer objects Right click on the DAL folder and add a ProductViewModel. Add the following code. This class contains properties we need to render our report. public class ProductViewModel { public int? ProductID { get; set; } public string ProductName { get; set; } public System.Nullable<decimal> UnitPrice { get; set; } public string CategoryName { get; set; } public int? CategoryID { get; set; } public int? SupplierID { get; set; } public bool Discontinued { get; set; } } Add a SupplierViewModel class. This will be used to render the supplier DropDownlist. public class SupplierViewModel { public string CompanyName { get; set; } public int SupplierID { get; set; } } Add a CategoryViewModel class. public class CategoryViewModel { public string CategoryName { get; set; } public int CategoryID { get; set; } } Create an IProductRepository interface. This will contain the signatures of all the methods we need when accessing the entity model.  This step is not needed but follows the repository pattern. interface IProductRepository { IQueryable<Product> GetProducts(); IQueryable<ProductViewModel> GetProductsProjected(int? supplierID, int? categoryID); IQueryable<SupplierViewModel> GetSuppliers(); IQueryable<CategoryViewModel> GetCategories(); } Create a ProductRepository class that implements the IProductReposity above. The methods available in this class are as follows: GetProducts – returns an IQueryable of all products. GetProductsProjected – returns an IQueryable of ProductViewModel. The method filters all the products based on SupplierId and CategoryId if any. It then projects the result into the ProductViewModel. GetSuppliers() – returns an IQueryable of all suppliers projected into a SupplierViewModel GetCategories() – returns an IQueryable of all categories projected into a CategoryViewModel  public class ProductRepository : IProductRepository { /// <summary> /// IQueryable of all Products /// </summary> /// <returns></returns> public IQueryable<Product> GetProducts() { var dataContext = new NorthwindEntities(); var products = from p in dataContext.Products select p; return products; }   /// <summary> /// IQueryable of Projects projected /// into the ProductViewModel class /// </summary> /// <returns></returns> public IQueryable<ProductViewModel> GetProductsProjected(int? supplierID, int? categoryID) { var projectedProducts = from p in GetProducts() select new ProductViewModel { ProductID = p.ProductID, ProductName = p.ProductName, UnitPrice = p.UnitPrice, CategoryName = p.Category.CategoryName, CategoryID = p.CategoryID, SupplierID = p.SupplierID, Discontinued = p.Discontinued }; // Filter on SupplierID if (supplierID.HasValue) { projectedProducts = projectedProducts.Where(a => a.SupplierID == supplierID); }   // Filter on CategoryID if (categoryID.HasValue) { projectedProducts = projectedProducts.Where(a => a.CategoryID == categoryID); }   return projectedProducts; }     public IQueryable<SupplierViewModel> GetSuppliers() { var dataContext = new NorthwindEntities(); var suppliers = from s in dataContext.Suppliers select new SupplierViewModel { SupplierID = s.SupplierID, CompanyName = s.CompanyName }; return suppliers; }   public IQueryable<CategoryViewModel> GetCategories() { var dataContext = new NorthwindEntities(); var categories = from c in dataContext.Categories select new CategoryViewModel { CategoryID = c.CategoryID, CategoryName = c.CategoryName }; return categories; } } Your solution explorer should look like the following. Build your project and make sure you don’t get any errors. In the next part, we will see how to create the client report definition file using the Report Wizard.   Creating an ASP.NET report using Visual Studio 2010 - Part 2

  Read the article

• Unable to run Wix Custom Action in MSI

  - by Grandpappy

  I'm trying to create a custom action for my Wix install, and it's just not working, and I'm unsure why. Here's the bit in the appropriate Wix File: <Binary Id="INSTALLERHELPER" SourceFile=".\Lib\InstallerHelper.dll" /> <CustomAction Id="HelperAction" BinaryKey="INSTALLERHELPER" DllEntry="CustomAction1" Execute="immediate" /> Here's the full class file for my custom action: using Microsoft.Deployment.WindowsInstaller; namespace InstallerHelper { public class CustomActions { [CustomAction] public static ActionResult CustomAction1(Session session) { session.Log("Begin CustomAction1"); return ActionResult.Success; } } } The action is run by a button press in the UI (for now): <Control Id="Next" Type="PushButton" X="248" Y="243" Width="56" Height="17" Default="yes" Text="!(loc.WixUINext)" > <Publish Event="DoAction" Value="HelperAction">1</Publish> </Control> When I run the MSI, I get this error in the log: MSI (c) (08:5C) [10:08:36:978]: Connected to service for CA interface. MSI (c) (08:4C) [10:08:37:030]: Note: 1: 1723 2: SQLHelperAction 3: CustomAction1 4: C:\Users\NATHAN~1.TYL\AppData\Local\Temp\MSI684F.tmp Error 1723. There is a problem with this Windows Installer package. A DLL required for this install to complete could not be run. Contact your support personnel or package vendor. Action SQLHelperAction, entry: CustomAction1, library: C:\Users\NATHAN~1.TYL\AppData\Local\Temp\MSI684F.tmp MSI (c) (08:4C) [10:08:38:501]: Product: SessionWorks :: Judge Edition -- Error 1723. There is a problem with this Windows Installer package. A DLL required for this install to complete could not be run. Contact your support personnel or package vendor. Action SQLHelperAction, entry: CustomAction1, library: C:\Users\NATHAN~1.TYL\AppData\Local\Temp\MSI684F.tmp Action ended 10:08:38: SQLHelperAction. Return value 3. DEBUG: Error 2896: Executing action SQLHelperAction failed. The installer has encountered an unexpected error installing this package. This may indicate a problem with this package. The error code is 2896. The arguments are: SQLHelperAction, , Neither of the two error codes or messages it gives me is enough to tell me what's wrong. Or perhaps I'm just not understanding what they're saying is wrong. At first I thought it might be because I was using Wix 3.5, so just to be sure I tried using Wix 3.0, but I get the same error. Any ideas on what I'm doing wrong?

  Read the article

• Pre-filtering and shaping OData feeds using WCF Data Services and the Entity Framework - Part 1

  - by rajbk

  The Open Data Protocol, referred to as OData, is a new data-sharing standard that breaks down silos and fosters an interoperative ecosystem for data consumers (clients) and producers (services) that is far more powerful than currently possible. It enables more applications to make sense of a broader set of data, and helps every data service and client add value to the whole ecosystem. WCF Data Services (previously known as ADO.NET Data Services), then, was the first Microsoft technology to support the Open Data Protocol in Visual Studio 2008 SP1. It provides developers with client libraries for .NET, Silverlight, AJAX, PHP and Java. Microsoft now also supports OData in SQL Server 2008 R2, Windows Azure Storage, Excel 2010 (through PowerPivot), and SharePoint 2010. Many other other applications in the works. * This post walks you through how to create an OData feed, define a shape for the data and pre-filter the data using Visual Studio 2010, WCF Data Services and the Entity Framework. A sample project is attached at the bottom of Part 2 of this post. Pre-filtering and shaping OData feeds using WCF Data Services and the Entity Framework - Part 2 Create the Web Application File –› New –› Project, Select “ASP.NET Empty Web Application” Add the Entity Data Model Right click on the Web Application in the Solution Explorer and select “Add New Item..” Select “ADO.NET Entity Data Model” under "Data”. Name the Model “Northwind” and click “Add”.   In the “Choose Model Contents”, select “Generate Model From Database” and click “Next”   Define a connection to your database containing the Northwind database in the next screen. We are going to expose the Products table through our OData feed. Select “Products” in the “Choose your Database Object” screen.   Click “Finish”. We are done creating our Entity Data Model. Save the Northwind.edmx file created. Add the WCF Data Service Right click on the Web Application in the Solution Explorer and select “Add New Item..” Select “WCF Data Service” from the list and call the service “DataService” (creative, huh?). Click “Add”.   Enable Access to the Data Service Open the DataService.svc.cs class. The class is well commented and instructs us on the next steps. public class DataService : DataService< /* TODO: put your data source class name here */ > { // This method is called only once to initialize service-wide policies. public static void InitializeService(DataServiceConfiguration config) { // TODO: set rules to indicate which entity sets and service operations are visible, updatable, etc. // Examples: // config.SetEntitySetAccessRule("MyEntityset", EntitySetRights.AllRead); // config.SetServiceOperationAccessRule("MyServiceOperation", ServiceOperationRights.All); config.DataServiceBehavior.MaxProtocolVersion = DataServiceProtocolVersion.V2; } } Replace the comment that starts with “/* TODO:” with “NorthwindEntities” (the entity container name of the Model we created earlier).  WCF Data Services is initially locked down by default, FTW! No data is exposed without you explicitly setting it. You have explicitly specify which Entity sets you wish to expose and what rights are allowed by using the SetEntitySetAccessRule. The SetServiceOperationAccessRule on the other hand sets rules for a specified operation. Let us define an access rule to expose the Products Entity we created earlier. We use the EnititySetRights.AllRead since we want to give read only access. Our modified code is shown below. public class DataService : DataService<NorthwindEntities> { public static void InitializeService(DataServiceConfiguration config) { config.SetEntitySetAccessRule("Products", EntitySetRights.AllRead); config.DataServiceBehavior.MaxProtocolVersion = DataServiceProtocolVersion.V2; } } We are done setting up our ODataFeed! Compile your project. Right click on DataService.svc and select “View in Browser” to see the OData feed. To view the feed in IE, you must make sure that "Feed Reading View" is turned off. You set this under Tools -› Internet Options -› Content tab.   If you navigate to “Products”, you should see the Products feed. Note also that URIs are case sensitive. ie. Products work but products doesn’t.   Filtering our data OData has a set of system query operations you can use to perform common operations against data exposed by the model. For example, to see only Products in CategoryID 2, we can use the following request: /DataService.svc/Products?$filter=CategoryID eq 2 At the time of this writing, supported operations are $orderby, $top, $skip, $filter, $expand, $format†, $select, $inlinecount. Pre-filtering our data using Query Interceptors The Product feed currently returns all Products. We want to change that so that it contains only Products that have not been discontinued. WCF introduces the concept of interceptors which allows us to inject custom validation/policy logic into the request/response pipeline of a WCF data service. We will use a QueryInterceptor to pre-filter the data so that it returns only Products that are not discontinued. To create a QueryInterceptor, write a method that returns an Expression<Func<T, bool>> and mark it with the QueryInterceptor attribute as shown below. [QueryInterceptor("Products")] public Expression<Func<Product, bool>> OnReadProducts() { return o => o.Discontinued == false; } Viewing the feed after compilation will only show products that have not been discontinued. We also confirm this by looking at the WHERE clause in the SQL generated by the entity framework. SELECT [Extent1].[ProductID] AS [ProductID], ... ... [Extent1].[Discontinued] AS [Discontinued] FROM [dbo].[Products] AS [Extent1] WHERE 0 = [Extent1].[Discontinued] Other examples of Query/Change interceptors can be seen here including an example to filter data based on the identity of the authenticated user. We are done pre-filtering our data. In the next part of this post, we will see how to shape our data. Pre-filtering and shaping OData feeds using WCF Data Services and the Entity Framework - Part 2 Foot Notes * http://msdn.microsoft.com/en-us/data/aa937697.aspx † $format did not work for me. The way to get a Json response is to include the following in the  request header “Accept: application/json, text/javascript, */*” when making the request. This is easily done with most JavaScript libraries.

  Read the article

• Failed to launch simulated application: iPhone Simulator failed to find the process ID of com.iAndAp

  - by Nicsoft

  Hello, I'm having this annoyning problem giving this message in the console: Failed to launch simulated application: iPhone Simulator failed to find the process ID of com.iAndApp.BlockPop. When trying to Build and Run, the application builds fine. The simulator starts but doesn't start the application. However, it manages to do something since the icon for the app is installed in the simulator. I have been searching to find the answer and tried a couple of things, none that worked. This happens for both new and old projects. I.e. when I create a new project I will receive the same error message. I've tried several projects of which all get the same error, so it's not related to the code (and successful builds proves it). Among other things I have updated to xCode 3.2.2. in order to try to solve the problem. Using Mac OSX 10.6.3. Here are the logs: 1. 2010-05-30 17.20.39 SpringBoard[15713] Unable to create CFServerConnection. Telephony state may be incorrect. 2010-05-30 17.20.40 SpringBoard[15713] Unable to create CFServerConnection. Telephony state may be incorrect. 2010-05-30 17.20.40 SpringBoard[15713] Unable to create CFServerConnection. Telephony state may be incorrect. 2010-05-30 17.20.40 SpringBoard[15713] Unable to create CFServerConnection. Telephony state may be incorrect. 2010-05-30 17.20.40 SpringBoard[15713] Can't find the translation dictionary, loadTranslationDictionaries 2010-05-30 17.20.40 SpringBoard[15713] Unable to create CFServerConnection. Telephony state may be incorrect. 2010-05-30 17.20.40 SpringBoard[15713] Unable to create CFServerConnection. Telephony state may be incorrect. 2010-05-30 17.20.41 SpringBoard[15713] Launchd returned an unexpected type or didn't return a value for job label UIKitApplication:com.iAndApp.BlockPop[0x8abd] with job key PID 2010-05-30 17.20.41 SpringBoard[15713] Unable to create CFServerConnection. Telephony state may be incorrect. 2010-05-30 17.21.10 Xcode[15496] Error launching simulated application: Error Domain=DTiPhoneSimulatorErrorDomain Code=1 UserInfo=0x200edcc00 "iPhone Simulator failed to find the process ID of com.iAndApp.BlockPop." 2. Form system.log May 30 17:20:39 Niklas-Johanssons-Mac-mini mobile_installationd[15712]: a0bc84e0 init_simulator_paths: No simulator root specified. Falling back to environment variable. May 30 17:20:39: --- last message repeated 5 times --- May 30 17:20:39 Niklas-Johanssons-Mac-mini mobile_installationd[15712]: b0081000 init_simulator_paths: No simulator root specified. Falling back to environment variable. May 30 17:20:39: --- last message repeated 1 time --- May 30 17:20:39 Niklas-Johanssons-Mac-mini mobile_installationd[15712]: b0081000 load_application_info: Could not load signer identity from /Users/Niklas/Library/Application Support/iPhone Simulator/3.0/Applications/1CD7E4BA-14D3-45A5-A05E-E552C04BCD4D/BlockPopLite.app/BlockPopLite May 30 17:20:39 Niklas-Johanssons-Mac-mini mobile_installationd[15712]: b0081000 load_application_info: Could not load signer identity from /Users/Niklas/Library/Application Support/iPhone Simulator/3.0/Applications/62585F19-5FAD-4548-89DF-C9AE621FCCD7/SysSound.app/SysSound May 30 17:20:39 Niklas-Johanssons-Mac-mini mobile_installationd[15712]: b0081000 load_application_info: Could not load signer identity from /Users/Niklas/Library/Application Support/iPhone Simulator/3.0/Applications/81AA51A5-7BFC-442F-BFF8-91E9C6EF13CD/BlockPop.app/BlockPop May 30 17:20:39 Niklas-Johanssons-Mac-mini mobile_installationd[15712]: b0103000 load_application_info: Could not load signer identity from /Users/Niklas/Library/Application Support/iPhone Simulator/3.0/Applications/A2DCBF96-8F15-4527-BDF1-BD90B34D401C/BlockPop.app/BlockPop May 30 17:20:39 Niklas-Johanssons-Mac-mini mobile_installationd[15712]: b0081000 init_simulator_paths: No simulator root specified. Falling back to environment variable. May 30 17:20:39: --- last message repeated 1 time --- May 30 17:20:39 Niklas-Johanssons-Mac-mini SpringBoard[15713]: Unable to create CFServerConnection. Telephony state may be incorrect. May 30 17:20:40 Niklas-Johanssons-Mac-mini mobile_installationd[15712]: b0081000 init_simulator_paths: No simulator root specified. Falling back to environment variable. May 30 17:20:40: --- last message repeated 1 time --- May 30 17:20:40 Niklas-Johanssons-Mac-mini SpringBoard[15713]: Unable to create CFServerConnection. Telephony state may be incorrect. May 30 17:20:40: --- last message repeated 2 times --- May 30 17:20:40 Niklas-Johanssons-Mac-mini SpringBoard[15713]: Can't find the translation dictionary, loadTranslationDictionaries May 30 17:20:40 Niklas-Johanssons-Mac-mini mobile_installationd[15712]: b0081000 init_simulator_paths: No simulator root specified. Falling back to environment variable. May 30 17:20:40: --- last message repeated 3 times --- May 30 17:20:40 Niklas-Johanssons-Mac-mini SpringBoard[15713]: Unable to create CFServerConnection. Telephony state may be incorrect. May 30 17:20:41: --- last message repeated 1 time --- May 30 17:20:41 Niklas-Johanssons-Mac-mini SpringBoard[15713]: Launchd returned an unexpected type or didn't return a value for job label UIKitApplication:com.iAndApp.BlockPop[0x8abd] with job key PID May 30 17:20:41 Niklas-Johanssons-Mac-mini SpringBoard[15713]: Unable to create CFServerConnection. Telephony state may be incorrect. May 30 17:21:10 Niklas-Johanssons-Mac-mini Xcode[15496]: Error launching simulated application: Error Domain=DTiPhoneSimulatorErrorDomain Code=1 UserInfo=0x200edcc00 "iPhone Simulator failed to find the process ID of com.iAndApp.BlockPop." Where do I start? I am really stuck and would be most greatful for any help!

  Read the article

• Facebook FQL - How do I fetch the posts I made to a friend's wall

  - by simianarmy

  I have a facebook desktop app with some test users all having granted the stream_read & offline access permissions. I can easily retrieve posts to each users' stream & profile. What I cannot do easily is retrieve posts that a user has made to one of their friend's walls. In fact, this used to work with a rather complex multiquery, but has stopped working now, or is working only intermittently... Does anyone care to share their method if one exists or discuss what restrictions there might be to this type of complex querying?

  Read the article

• ASP.NET MVC 2 and authentication using WIF (Windows Identity Foundation)

  - by Russ Cam

  Are there any decent examples of the following available: Looking through the WIF SDK, there are examples of using WIF in conjunction with ASP.NET using the WSFederationAuthenticationModule (FAM) to redirect to an ASP.NET site thin skin on top of a Security Token Service (STS) that user uses to authenticate (via supplying a username and password). If I understand WIF and claims-based access correctly, I would like my application to provide its own login screen where users provide their username and password and let this delegate to an STS for authentication, sending the login details to an endpoint via a security standard (WS-*), and expecting a SAML token to be returned. Ideally, the SessionAuthenticationModule would work as per the examples using FAM in conjunction with SessionAuthenticationModule i.e. be responsible for reconstructing the IClaimsPrincipal from the session security chunked cookie and redirecting to my application login page when the security session expires. Is what I describe possible using FAM and SessionAuthenticationModule with appropriate web.config settings, or do I need to think about writing a HttpModule myself to handle this? Alternatively, is redirecting to a thin web site STS where users log in the de facto approach in a passive requestor scenario?

  Read the article

• cakephp routing problem, plugin routing works but not others

  - by Paul

  I'm having a strange routing problem with a site I just uploaded, and I've made a number of changes to test what's happening. It doesn't make any sense. My setup is: - I'm using one plugin, which I've included all the routing in the routes.php file. - I've also included the routes for two other controllers, 'events' and 'updates' they look like this: Router::connect('/login', array('plugin' = 'pippoacl', 'controller' = 'users', 'action' = 'login')); Router::connect('/logout', array('plugin' = 'pippoacl', 'controller' = 'users', 'action' = 'logout')); Router::connect( '/events/', array( 'controller' = 'events', 'action' = 'index')); Router::connect('/updates', array('controller' = 'updates', 'action' = 'index')); What happens when I try to get to 'events' is that I get an error message saying: "Not Found Error: The requested address '/Events' was not found on this server." I've checked the database and it's accessible, through the plugin's model/controller/view. I've also made sure the model/controllers for 'events' and 'updates' are there. Can anyone tell me how to trouble shoot this? Thanks, Paul

  Read the article

• SSIS Lookup component tuning tips

  - by jamiet

  Yesterday evening I attended a London meeting of the UK SQL Server User Group at Microsoft’s offices in London Victoria. As usual it was both a fun and informative evening and in particular there seemed to be a few questions arising about tuning the SSIS Lookup component; I rattled off some comments and figured it would be prudent to drop some of them into a dedicated blog post, hence the one you are reading right now. Scene setting A popular pattern in SSIS is to use a Lookup component to determine whether a record in the pipeline already exists in the intended destination table or not and I cover this pattern in my 2006 blog post Checking if a row exists and if it does, has it changed? (note to self: must rewrite that blog post for SSIS2008). Fundamentally the SSIS lookup component (when using FullCache option) sucks some data out of a database and holds it in memory so that it can be compared to data in the pipeline. One of the big benefits of using SSIS dataflows is that they process data one buffer at a time; that means that not all of the data from your source exists in the dataflow at the same time and is why a SSIS dataflow can process data volumes that far exceed the available memory. However, that only applies to data in the pipeline; for reasons that are hopefully obvious ALL of the data in the lookup set must exist in the memory cache for the duration of the dataflow’s execution which means that any memory used by the lookup cache will not be available to be used as a pipeline buffer. Moreover, there’s an obvious correlation between the amount of data in the lookup cache and the time it takes to charge that cache; the more data you have then the longer it will take to charge and the longer you have to wait until the dataflow actually starts to do anything. For these reasons your goal is simple: ensure that the lookup cache contains as little data as possible. General tips Here is a simple tick list you can follow in order to tune your lookups: Use a SQL statement to charge your cache, don’t just pick a table from the dropdown list made available to you. (Read why in SELECT *... or select from a dropdown in an OLE DB Source component?) Only pick the columns that you need, ignore everything else Make the database columns that your cache is populated from as narrow as possible. If a column is defined as VARCHAR(20) then SSIS will allocate 20 bytes for every value in that column – that is a big waste if the actual values are significantly less than 20 characters in length. Do you need DT_WSTR typed columns or will DT_STR suffice? DT_WSTR uses twice the amount of space to hold values that can be stored using a DT_STR so if you can use DT_STR, consider doing so. Same principle goes for the numerical datatypes DT_I2/DT_I4/DT_I8. Only populate the cache with data that you KNOW you will need. In other words, think about your WHERE clause! Thinking outside the box It is tempting to build a large monolithic dataflow that does many things, one of which is a Lookup. Often though you can make better use of your available resources by, well, mixing things up a little and here are a few ideas to get your creative juices flowing: There is no rule that says everything has to happen in a single dataflow. If you have some particularly resource intensive lookups then consider putting that lookup into a dataflow all of its own and using raw files to pass the pipeline data in and out of that dataflow. Know your data. If you think, for example, that the majority of your incoming rows will match with only a small subset of your lookup data then consider chaining multiple lookup components together; the first would use a FullCache containing that data subset and the remaining data that doesn’t find a match could be passed to a second lookup that perhaps uses a NoCache lookup thus negating the need to pull all of that least-used lookup data into memory. Do you need to process all of your incoming data all at once? If you can process different partitions of your data separately then you can partition your lookup cache as well. For example, if you are using a lookup to convert a location into a [LocationId] then why not process your data one region at a time? This will mean your lookup cache only has to contain data for the location that you are currently processing and with the ability of the Lookup in SSIS2008 and beyond to charge the cache using a dynamically built SQL statement you’ll be able to achieve it using the same dataflow and simply loop over it using a ForEach loop. Taking the previous data partitioning idea further … a dataflow can contain more than one data path so why not split your data using a conditional split component and, again, charge your lookup caches with only the data that they need for that partition. Lookups have two uses: to (1) find a matching row from the lookup set and (2) put attributes from that matching row into the pipeline. Ask yourself, do you need to do these two things at the same time? After all once you have the key column(s) from your lookup set then you can use that key to get the rest of attributes further downstream, perhaps even in another dataflow. Are you using the same lookup data set multiple times? If so, consider the file caching option in SSIS 2008 and beyond. Above all, experiment and be creative with different combinations. You may be surprised at what works. Final  thoughts If you want to know more about how the Lookup component differs in SSIS2008 from SSIS2005 then I have a dedicated blog post about that at Lookup component gets a makeover. I am on a mini-crusade at the moment to get a BULK MERGE feature into the database engine, the thinking being that if the database engine can quickly merge massive amounts of data in a similar manner to how it can insert massive amounts using BULK INSERT then that’s a lot of work that wouldn’t have to be done in the SSIS pipeline. If you think that is a good idea then go and vote for BULK MERGE on Connect. If you have any other tips to share then please stick them in the comments. Hope this helps! @Jamiet Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• How to resolve symbolic links in a shell script

  - by Greg Hewgill

  Given an absolute or relative path (in a Unix-like system), I would like to determine the full path of the target after resolving any intermediate symlinks. Bonus points for also resolving ~username notation at the same time. If the target is a directory, it might be possible to chdir() into the directory and then call getcwd(), but I really want to do this from a shell script rather than writing a C helper. Unfortunately, shells have a tendency to try to hide the existence of symlinks from the user (this is bash on OS X): $ ls -ld foo bar drwxr-xr-x 2 greg greg 68 Aug 11 22:36 bar lrwxr-xr-x 1 greg greg 3 Aug 11 22:36 foo -> bar $ cd foo $ pwd /Users/greg/tmp/foo $ What I want is a function resolve() such that when executed from the tmp directory in the above example, resolve("foo") == "/Users/greg/tmp/bar".

  Read the article

• What useful things could a javaScript library provide?

  - by Delan Azabani

  In many of my answers I repeatedly urge users not to use JavaScript libraries like jQuery. I even wrote a blog post about the problems that using a library create. Some of these problems include holding back native standards development, keeping users comfortably using IE, and abstracting the developer from real JavaScript. If a site doesn't require IE as part of its audience, then how are libraries useful? The other popular browsers share extremely similar implementations and work well with things like JavaScript 1.6 arrays and AJAX. This is not a troll question, I'm truly wondering what they're useful for.

  Read the article

• Create shortcut from vb.net on Windows 7 box (64 bit)

  - by Matt

  I am trying to create a desktop shortcut from vb.net code on a Windows 7 box (64 bit). The following code works on XP, but when run on Win7 I just get a message stating the App has stopped working: Imports IWshRuntimeLibrary Dim WshShell As WshShellClass = New WshShellClass Dim MyShortcut As IWshRuntimeLibrary.IWshShortcut ' The shortcut will be created on the desktop 'Win 7 MyShortcut = CType(WshShell.CreateShortcut("C:\Users\Public\Desktop\iexplore.lnk"), IWshRuntimeLibrary.IWshShortcut) 'MyShortcut = CType(WshShell.CreateShortcut("C:\Documents and Settings\All Users\Desktop\iexplore.lnk"), IWshRuntimeLibrary.IWshShortcut) MyShortcut.TargetPath = "C:\Program Files\Internet Explorer\iexplore.exe" 'Specify target app full path MyShortcut.Description = "IE" MyShortcut.Save() Any thoughts or better ways to create a shorcut from code on a Win7 box?

  Read the article

• MSBuild: Add additional files to compile without altering the project file

  - by Craig Norton

  After looking around I can't find a simple answer to this problem. I am trying to create an MSBuild file to allow me to easily use SpecFlow and NUnit within Visual Studio 2010 express. The file below is not complete this is just a proof of concept and it needs to be made more generic. <Project DefaultTargets="Build" xmlns="http://schemas.microsoft.com/developer/msbuild/2003"> <PropertyGroup> <BuildDependsOn> BuildSolution; SpecFlow; BuildProject; NUnit; </BuildDependsOn> </PropertyGroup> <PropertyGroup> <Solution>C:\Users\Craig\Documents\My Dropbox\Cells\Cells.sln</Solution> <CSProject>C:\Users\Craig\Documents\My Dropbox\Cells\Configuration\Configuration.csproj</CSProject> <DLL>C:\Users\Craig\Documents\My Dropbox\Cells\Configuration\bin\Debug\Configuration.dll</DLL> </PropertyGroup> <Target Name="Build" DependsOnTargets="$(BuildDependsOn)"> </Target> <Target Name="BuildSolution"> <MSBuild Projects="$(Solution)" Properties="Configuration=Debug" /> </Target> <Target Name="SpecFlow"> <Exec Command="SpecFlow generateall $(CSProject)" /> </Target> <Target Name="BuildProject"> <MSBuild Projects="$(CSProject)" Properties="Configuration=Debug" /> </Target> <Target Name="NUnit"> <Exec Command='NUnit /run "$(DLL)"' /> </Target> The SpecFlow Task looks in the .csproj file and creates a SpecFlowFeature1.feature.cs. I need to include this file when building the .csproj so that NUnit can use it. I know I could modify (either directly or on a copy) the .csproj file to include the generated file but I'd prefer to avoid this. My question is: Is there a way to use the MSBuild Task to build the project file and tell it to include an additional file to include in the build? Thank you.

  Read the article

• ruby on rails configuration

  - by Themasterhimself

  Im using the following guide for getting started with rails for ubuntu 9.10. http://guides.rails.info/getting_started.html I have installed both ruby and gem. gokul@gokul-laptop:~$ ruby -v ruby 1.8.7 (2009-06-12 patchlevel 174) [i486-linux] gokul@gokul-laptop:~$ gem -v 1.3.6 gokul@gokul-laptop:~$ For rails, gokul@gokul-laptop:~$sudo gem install rails doesnt seem to give any response. so used the synaptic package manager for installing it. And it seems to have installed correctly. gokul@gokul-laptop:~$ rails Usage: /usr/bin/rails /path/to/your/app [options] Options: -r, --ruby=path Path to the Ruby binary of your choice (otherwise scripts use env, dispatchers current path). Default: /usr/bin/ruby1.8 -d, --database=name Preconfigure for selected database (options: mysql/oracle/postgresql/sqlite2/sqlite3/frontbase/ibm_db). Default: sqlite3 -D, --with-dispatchers Add CGI/FastCGI/mod_ruby dispatches code to generated application skeleton Default: false --freeze Freeze Rails in vendor/rails from the gems generating the skeleton Default: false -m, --template=path Use an application template that lives at path (can be a filesystem path or URL). Default: (none) Rails Info: -v, --version Show the Rails version number and quit. -h, --help Show this help message and quit. General Options: -p, --pretend Run but do not make any changes. -f, --force Overwrite files that already exist. -s, --skip Skip files that already exist. -q, --quiet Suppress normal output. -t, --backtrace Debugging: show backtrace on errors. -c, --svn Modify files with subversion. (Note: svn must be in path) -g, --git Modify files with git. (Note: git must be in path) Description: The 'rails' command creates a new Rails application with a default directory structure and configuration at the path you specify. Example: rails ~/Code/Ruby/weblog This generates a skeletal Rails installation in ~/Code/Ruby/weblog. See the README in the newly created application to get going. gokul@gokul-laptop:~$ app folder is created with all the proper folders. The problem starts with the following commands... gokul@gokul-laptop:~$ sudo gem install bundler [sudo] password for gokul: Successfully installed bundler-0.9.24 1 gem installed Installing ri documentation for bundler-0.9.24... Installing RDoc documentation for bundler-0.9.24... gokul@gokul-laptop:~$ bundle install Could not locate Gemfile gokul@gokul-laptop:~$ coming to the database, the default sqlite3 seems to have installed correctly. gokul@gokul-laptop:~$ sqlite3 SQLite version 3.6.16 Enter ".help" for instructions Enter SQL statements terminated with a ";" sqlite The welcome aboard page is not being able to be found at (http://localhost:3000) after executing the following commands... gokul@gokul-laptop:~/Desktop$ rails blog create create app/controllers create app/helpers create app/models create app/views/layouts create config/environments create config/initializers create config/locales create db create doc create lib create lib/tasks create log create public/images create public/javascripts create public/stylesheets create script/performance create test/fixtures create test/functional create test/integration create test/performance create test/unit create vendor create vendor/plugins create tmp/sessions create tmp/sockets create tmp/cache create tmp/pids create Rakefile create README create app/controllers/application_controller.rb create app/helpers/application_helper.rb create config/database.yml create config/routes.rb create config/locales/en.yml create db/seeds.rb create config/initializers/backtrace_silencers.rb create config/initializers/inflections.rb create config/initializers/mime_types.rb create config/initializers/new_rails_defaults.rb create config/initializers/session_store.rb create config/environment.rb create config/boot.rb create config/environments/production.rb create config/environments/development.rb create config/environments/test.rb create script/about create script/console create script/dbconsole create script/destroy create script/generate create script/runner create script/server create script/plugin create script/performance/benchmarker create script/performance/profiler create test/test_helper.rb create test/performance/browsing_test.rb create public/404.html create public/422.html create public/500.html create public/index.html create public/favicon.ico create public/robots.txt create public/images/rails.png create public/javascripts/prototype.js create public/javascripts/effects.js create public/javascripts/dragdrop.js create public/javascripts/controls.js create public/javascripts/application.js create doc/README_FOR_APP create log/server.log create log/production.log create log/development.log create log/test.log gokul@gokul-laptop:~/Desktop$ cd blog gokul@gokul-laptop:~/Desktop/blog$ rake db:create (in /home/gokul/Desktop/blog) gokul@gokul-laptop:~/Desktop/blog$ rails server create create app/controllers create app/helpers create app/models create app/views/layouts create config/environments create config/initializers create config/locales create db create doc create lib create lib/tasks create log create public/images create public/javascripts create public/stylesheets create script/performance create test/fixtures create test/functional create test/integration create test/performance create test/unit create vendor create vendor/plugins create tmp/sessions create tmp/sockets create tmp/cache create tmp/pids create Rakefile create README create app/controllers/application_controller.rb create app/helpers/application_helper.rb create config/database.yml create config/routes.rb create config/locales/en.yml create db/seeds.rb create config/initializers/backtrace_silencers.rb create config/initializers/inflections.rb create config/initializers/mime_types.rb create config/initializers/new_rails_defaults.rb create config/initializers/session_store.rb create config/environment.rb create config/boot.rb create config/environments/production.rb create config/environments/development.rb create config/environments/test.rb create script/about create script/console create script/dbconsole create script/destroy create script/generate create script/runner create script/server create script/plugin create script/performance/benchmarker create script/performance/profiler create test/test_helper.rb create test/performance/browsing_test.rb create public/404.html create public/422.html create public/500.html create public/index.html create public/favicon.ico create public/robots.txt create public/images/rails.png create public/javascripts/prototype.js create public/javascripts/effects.js create public/javascripts/dragdrop.js create public/javascripts/controls.js create public/javascripts/application.js create doc/README_FOR_APP create log/server.log create log/production.log create log/development.log create log/test.log gokul@gokul-laptop:~/Desktop/blog$ hope some one can help me with this...

  Read the article

• Improving ANTLR DSL parse-error messages

  - by Dan Fabulich

  I'm working on a domain-specific language (DSL) for non-programmers. Non-programmers make a lot of grammar mistakes: they misspell keywords, they don't close parentheses, they don't terminate blocks, etc. I'm using ANTLR to generate my parser; it provides a nifty mechanism for handling RecognitionExceptions to improve error handling. But I'm finding it pretty hard to develop good error-handling code for my DSL. At this point, I'm considering ways to simplify the language to make it easier for me to provide users with high-quality error messages, but I'm not really sure how to go about this. I think I want to reduce the ambiguity of errors somehow, but I'm not sure how to implement that idea in a grammar. In what ways can I simplify my language to improve parse-error messages for my users? EDIT: Updated to clarify that I'm interested in ways to simplify my language, not just ANTLR error-handling tips in general. (Though, thanks for those!)

  Read the article

• Facebox window closes after submit

  - by Kim Andersen

  Hi all I have a question regarding Facebox. When I click a certain link on my page, the Facebox modal window opens just fine. But inside this modal window I'd like to have a form that users can submit. When the users click the submit-button, the whole page refreshes, and my Facebox-window is closed. This makes sense to me, but I'd like it to work differently. I want to give the user a confirmation, inside of the modal window, after they have submitted the form. So when a user clicks the submit-button, a confirmation should be showed inside og the modal-window. Anybody know if this is possible? I hope that you understand my question :) Best regards Kim Andersen

  Read the article

• Ruby on Rails vs Grails vs. Spring ROO vs. Spring App

  - by lizdev

  Hi, I'm planning on writing a simple web application that will be used by lots of users (as complicated as a simple bookmarking app) and I'm trying to decide which framework/language to use. I'm very experienced with Spring/Hibernate and Java in general but new to both Grails and RoR (and Spring ROO). The only reason I'm considering RoR is because Java hosting is MUCH more expensive than RoR hosting (which is supported by almost any hosting vendor for 5$ per month). Assuming the price wasn't an issue, which one of the frameworks/languages mentioned above would you recommend for a Java developer (who knows how to configure Spring/Hibernate etc.)? I'm afraid that by using RoR I won't be able to easily support many users who are using the website at the same time. thanks

  Read the article

• ComboBox Binding inside Dataform Silverlight

  - by Sergio

  Hi, well I have my users table and my department table, so I have in XAML a Datagrid and a Dataform, in my dataform i have a combobox that is filled from the department table (all possible departments), I bind it to the Department attribute from my user, and it shows it. The problem is that when I click the edit button of the dataform the combobox goes blank... if i cancel the edit it goes back to the department of the user. Another thing is if i edit the user and choose a department when i commit the edit it works and when i edit that same user the combobox doesnt go blank now ... but for the other users it does if i havent specifically choosen the department in the combobox.

  Read the article

< Previous Page | 730 731 732 733 734 735 736 737 738 739 740 741  | Next Page >