Search Results

Search found 19795 results on 792 pages for '8 bit'.

Page 746/792 | < Previous Page | 742 743 744 745 746 747 748 749 750 751 752 753  | Next Page >

• How to get rid of a stubborn 'removed' device in mdadm

  - by T.J. Crowder

  One of my server's drives failed and so I removed the failed drive from all three relevant arrays, had the drive swapped out, and then added the new drive to the arrays. Two of the arrays worked perfectly. The third added the drive back as a spare, and there's an odd "removed" entry in the mdadm details. I tried both mdadm /dev/md2 --remove failed and mdadm /dev/md2 --remove detached as suggested here and here, neither of which complained, but neither of which had any effect, either. Does anyone know how I can get rid of that entry and get the drive added back properly? (Ideally without resyncing a third time, I've already had to do it twice and it takes hours. But if that's what it takes, that's what it takes.) The new drive is /dev/sda, the relevant partition is /dev/sda3. Here's the detail on the array: # mdadm --detail /dev/md2 /dev/md2: Version : 0.90 Creation Time : Wed Oct 26 12:27:49 2011 Raid Level : raid1 Array Size : 729952192 (696.14 GiB 747.47 GB) Used Dev Size : 729952192 (696.14 GiB 747.47 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Tue Nov 12 17:48:53 2013 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 UUID : 2fdbf68c:d572d905:776c2c25:004bd7b2 (local to host blah) Events : 0.34665 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 19 1 active sync /dev/sdb3 2 8 3 - spare /dev/sda3 If it's relevant, it's a 64-bit server. It normally runs Ubuntu, but right now I'm in the data centre's "rescue" OS, which is Debian 7 (wheezy). The "removed" entry was there the last time I was in Ubuntu (it won't, currently, boot from the disk), so I don't think that's not some Ubuntu/Debian conflict (and they are, of course, closely related). Update: Having done extensive tests with test devices on a local machine, I'm just plain getting anomalous behavior from mdadm with this array. For instance, with /dev/sda3 removed from the array again, I did this: mdadm /dev/md2 --grow --force --raid-devices=1 And that got rid of the "removed" device, leaving me just with /dev/sdb3. Then I nuked /dev/sda3 (wrote a file system to it, so it didn't have the raid fs anymore), then: mdadm /dev/md2 --grow --raid-devices=2 ...which gave me an array with /dev/sdb3 in slot 0 and "removed" in slot 1 as you'd expect. Then mdadm /dev/md2 --add /dev/sda3 ...added it — as a spare again. (Another 3.5 hours down the drain.) So with the rebuilt spare in the array, given that mdadm's man page says RAID-DEVICES CHANGES ... When the number of devices is increased, any hot spares that are present will be activated immediately. ...I grew the array to three devices, to try to activate the "spare": mdadm /dev/md2 --grow --raid-devices=3 What did I get? Two "removed" devices, and the spare. And yet when I do this with a test array, I don't get this behavior. So I nuked /dev/sda3 again, used it to create a brand-new array, and am copying the data from the old array to the new one: rsync -r -t -v --exclude 'lost+found' --progress /mnt/oldarray/* /mnt/newarray This will, of course, take hours. Hopefully when I'm done, I can stop the old array entirely, nuke /dev/sdb3, and add it to the new array. Hopefully, it won't get added as a spare!

  Read the article

• Excel: conditionally format a cell using the format of another, content-matching cell

  - by Eric A. Meyer

  I have an Excel spreadsheet where I’d like to be able to create a “key” of formatted cells with unique values, and then in another sheet format cells using the key formatting. So for example, my key is as follows, with one value per cell and the visual formatting indicated in parentheses: A (red background) B (green background) C (blue background) So that’s on one sheet (or in a remote corner of the current sheet—whichever is better). Then, in an area that I mark for conditional formatting, I can type one of those three letters and have the cell where I typed it visually formatted according to the key. So if I type a “B” into one of the conditionally formatted cells, it gets a green background. (Note that I’m using backgrounds here solely for ease of explanation: ideally I want to have all visual formatting copied over, whether it’s foreground color, background color, font weight, borders, or whatever. But I’ll take what I can get, obviously.) And—just to make it extra-tricky—if I change the formatting in the key, that change should be reflected in cells that reference the key. Thus, if I change the “B” formatting in the key from a green background to a purple background, any “B” in the main sheet should switch to the new color. Similarly, it should be possible to add or remove values from the key and have those changes applied to the main data set. I’m okay with the formatting-update-on-key-change being triggered by clicking a button or something. I suspect that if any of this is possible it will require VBA, but I’ve never used it so I’ve no idea where to start if that’s the case. I’m hoping it’s possible without VBA. I know it’s possible to just use multiple conditional formats, but my use case here is that I’m trying to create the above-described capability for someone who isn’t conversant with conditional formatting. I’d like to let them be able to define a key, update it if necessary, and keep on truckin’ without me having to rewrite the spreadsheet’s formatting rules for them. --- UPDATE --- So I think I was a bit unclear about my original request. Let me try again with an image. The image shows the “key” on the left, where values and styles are defined using keyboard and mouse input. On the right, you see the data that should be formatted to match the key. Thus if I type a “C” into a cell in the Data area, it should be blue-backed. Furthermore, if I change the formatting of “C” in the Key to have a purple background, all the “C” cells should switch from blue to purple. For further craziness, if I add more to the Key (say, “D” with a yellow background) then any “D” cells will be styled to match; if I remove a Key entry, then matching values in the Data area should revert to default styling. So. Is that more clear? Is it possible, in whole or in part? I don’t have to use conditional formatting for this; in fact, at this point I suspect I probably shouldn’t. But I’m open to any approach!

  Read the article

• creating a heirarchy of terminals or workspaces

  - by intuited

  <rant This question occurred to me ('occurred' meaning 'whispered seductively in my ear for the 100th time') while using GNU-screen, so I'll make that my example. However this is a much more general question about user interfaces and what I perceive as a flawmissing feature in every implementation I've yet seen. I'm wondering if there is some way to create a heirarchy/tree of terminals in a screen session. EG I'd like to have something like 1 bash 1.1 bash 1.2 bash 2 bash 3 bash 3.1 bash 3.1.1 bash 3.1.2 bash It would be good if the terminals could be labelled instead of having to be navigated to via some arrangement that I suspect doesn't exist. So then you could jump to one using eg ^A:goto happydays or ^A:goto dykstra.angry. So to generalize that: Firefox, Chrome, Internet Explorer, gnome-terminal, roxterm, konsole, yakuake, OpenOffice, Microsoft Office, Mr. Snuffaluppagus's Funtime Carousel™, and Your Mom's Jam Browser™ all offer the ability to create a flat set of tabs containing documents of an identical nature: web pages, terminals, documents, fun rideable animals, and jams. GNU-screen implements the same functionality without using tabs. Linux and OS/X window managers provide the ability to organize windows into an array of workspaces, which amounts to again, the same deal. Over the past few years, this has become a more or less ubiquitous concept which has been righteously welcomed into the far reaches of the computer interface funfest. Heavy users of these systems quickly encounter a problem with it: the set of entities is flat. In the case of workspaces, an option may be available to create a 2d array. However none of these applications furnish their users with the ability to create heirarchies, similar to filesystem directory structures, containing instances of their particular contained type. I for one am consistently bothered by this, and am wondering if the community can offer some wisdom as to why this has not happened in any of the foremost collections of computational functionality our culture has yet produced. Or if perhaps it has and I'm just an ignorant savage. I'd like to be able to not only group things into a tree structure, but also to create references (aka symbolic links, aka pointers) from one part of the structure to another, as well as apply properties (eg default directory, colorscheme, ...) recursively downward from a given node. I see no reason why we shouldn't be able to save these structures as known sessions, and apply tags to particular instances. So then you can sort through them by tag, find them by name, or just use the arrow keys (with an appropriate modifier) to move left or right and in or out of a given level. Another key combo would serve to create a branch in the place of the current terminal/webpage/lifelike statue/spreadsheet/spreadsheet sheet/presentation/jam and move that entity into the new branch, then create a fresh one as a sibling to it: a second leaf node within the same branch node. They would get along well. I find it a bit astonishing that this hasn't happened yet, and the only reason I can venture as a guess is that the creators of these fine systems do not consider such functionality to be useful to a significant portion of their userbase. I posit that the probability that that such an assumption would be correct is pretty low. On the other hand, given the relative ease with which such structures can be implemented using modern libraries/languages, it doesn't seem likely that difficulty of implementation would be a major roadblock. If it could be done in 1972 or whenever within the constraints of a filesystem driver, it should be relatively painless to implement in 2010 in a fullblown application. Given that all of these systems are capable of maintaining a set of equivalent entities, it seems unlikely that a major infrastructure overhaul would be necessary in order to enable a navigable heirarchy of them. </rant Mostly I'm just looking to start up a discussion and/or brainstorming on this topic. Any ideas, examples, criticism, or analysis are quite welcome. * Mr. Snuffaluppagus's Funtime Carousel is a registered trademark of Children's Television Workshop Inc. * Your Mom's Jam Browser is a registered trademark of Your Mom Inc.

  Read the article

• Intelligent "Subtraction" of one text logfile from another

  - by Vi

  Example: Application generates large text log file A with many different messages. It generates similarly large log file B when does not function correctly. I want to see what messages in file B are essentially new, i.e. to filter-out everything from A. Trivial prototype is: Sort | uniq both files Join files sort | uniq -c grep -v "^2" This produces symmetric difference and inconvenient. How to do it better? (including non-symmetric difference and preserving of messages order in B) Program should first analyse A and learn which messages are common, then analyse B showing with messages needs attention. Ideally it should automatically disregard things like timestamps, line numbers or other volatile things. Example. A: 0:00:00.234 Received buffer 0x324234 0:00:00.237 Processeed buffer 0x324234 0:00:00.238 Send buffer 0x324255 0:00:03.334 Received buffer 0x324255 0:00:03.337 Processeed buffer 0x324255 0:00:03.339 Send buffer 0x324255 0:00:05.171 Received buffer 0x32421A 0:00:05.173 Processeed buffer 0x32421A 0:00:05.178 Send buffer 0x32421A B: 0:00:00.134 Received buffer 0x324111 0:00:00.137 Processeed buffer 0x324111 0:00:00.138 Send buffer 0x324111 0:00:03.334 Received buffer 0x324222 0:00:03.337 Processeed buffer 0x324222 0:00:03.338 Error processing buffer 0x324222 0:00:03.339 Send buffer 0x3242222 0:00:05.271 Received buffer 0x3242FA 0:00:05.273 Processeed buffer 0x3242FA 0:00:05.278 Send buffer 0x3242FA 0:00:07.280 Send buffer 0x3242FA failed Result: 0:00:03.338 Error processing buffer 0x324222 0:00:07.280 Send buffer 0x3242FA failed One of ways of solving it can be something like that: Split each line to logical units: 0:00:00.134 Received buffer 0x324111,0:00:00.134,Received,buffer,0x324111,324111,Received buffer, \d:\d\d:\d\d\.\d\d\d, \d+:\d+:\d+.\d+, 0x[0-9A-F]{6}, ... It should find individual words, simple patterns in numbers, common layouts (e.g. "some date than text than number than text than end_of_line"), also handle combinations of above. As it is not easy task, user assistance (adding regexes with explicit "disregard that","make the main factor","don't split to parts","consider as date/number","take care of order/quantity of such messages" rules) should be supported (but not required) for it. Find recurring units and "categorize" lines, filter out too volatile things like timestamps, addresses or line numbers. Analyse the second file, find things that has new logical units (one-time or recurring), or anything that will "amaze" the system which has got used to the first file. Example of doing some bit of this manually: $ cat A | head -n 1 0:00:00.234 Received buffer 0x324234 $ cat A | egrep -v "Received buffer" | head -n 1 0:00:00.237 Processeed buffer 0x324234 $ cat A | egrep -v "Received buffer|Processeed buffer" | head -n 1 0:00:00.238 Send buffer 0x324255 $ cat A | egrep -v "Received buffer|Processeed buffer|Send buffer" | head -n 1 $ cat B | egrep -v "Received buffer|Processeed buffer|Send buffer" 0:00:03.338 Error processing buffer 0x324222 0:00:07.280 Send buffer 0x3242FA failed This is a boring thing (there are a lot of message types); also I can accidentally include some too broad pattern. Also it can't handle complicated things like interrelation between messages. I know that it is AI-related. May be there are already developed tools?

  Read the article

• Coda 2 and SCP uploading files with the wrong permission

  - by Tom Black

  Currently I have a basic Ubuntu server running a website. The website is for a few students learning HTML/PHP and each student has their own account with a symbolic link to the shared website folder. Since the students are working on the website together, each user needs to be able to modify all the files (index.html for example). So I created a Webdev group containing all of the students with the default umask of 0002 set in their .bashrc (This allows newly created files to be 774). The shared folder is owned by the group Webdev with a chmod g+s so that new files/folders also belong to the group Webdev. The problem is that the students are using an IDE (Coda 2) and when they create a new file or folder using the IDE the file has the permissions of 644 on the server (not group writable). However when I make a new file through connecting with Cyberduck (SFTP client) the file permissions are 664 (as they should be). So I don't understand why Coda would be any different. However, after some trial and error I believe that Coda is first creating the file on local disk and then uploading that file to the server. On a mac by default a newly created file is 644. When the client uploads a file that's already 644 it stays 644 on the server side (umask is kind of useless in this situation). I've also tried creating ACL permissions for that folder but an uploaded file from my mac via SCP doesn't get the default ACL permissions. In Coda there is an option to change file permissions on a transfer. However this option seems to apply a chmod to all files being uploaded or saved. When one of students is modifying a file created by someone else when they try to upload the file or save it Coda tries to also do a chmod but fails because that user isn't the owner of the file. My current solution is using bindfs... I mount the shared web folder and bindfs sets permissions and group ownership of newly created files. However, bindfs seems to be a bit slow and I'm sure there is a better solution. Even if the students ditched Coda 2 and used Mac vim with scp the newly created files on the server would behave the same (644) which is default on the mac. Other options... 1) Either I teach the students to use (ssh/chmod) with their IDE to change their own file permissions when uploading. 2) I make all the students' Macs have the default umask of 0002 which would upload files with the right permissions. 3) Write a corn script to fix the file permissions every 5 to 15 minutes... (This option I think is the worst if students are working together at the same time). Is there any way that I could make all files that are uploaded via SCP have the default file permissions of 664 even though the uploaded file has a lower permission? (After hours of searching I don't think this is possible) I guess a corn script is my best option for novice users. How do web developers work together on larger sites? similar to this: http://serverfault.com/questions/283492/how-to-specify-file-permission-when-putting-a-file-using-openssh-sftp-command Also similar: http://serverfault.com/questions/395418/managing-linux-directory-permissions-sftp

  Read the article

• TLS (STARTTLS) Failure After 10.6 Upgrade to Open Directory Master

  - by Thomas Kishel

  Hello, Environment: Mac OS X 10.6.3 install/import of a MacOS X 10.5.8 Open Directory Master server. After that upgrade, LDAP+TLS fails on our MacOS X 10.5, 10.6, CentOS, Debian, and FreeBSD clients (Apache2 and PAM). Testing using ldapsearch: ldapsearch -ZZ -H ldap://gnome.darkhorse.com -v -x -b "dc=darkhorse,dc=com" '(uid=donaldr)' uid ... fails with: ldap_start_tls: Protocol error (2) Testing adding "-d 9" fails with: res_errno: 2, res_error: <unsupported extended operation>, res_matched: <> Testing without requiring STARTTLS or with LDAPS: ldapsearch -H ldap://gnome.darkhorse.com -v -x -b "dc=darkhorse,dc=com" '(uid=donaldr)' uid ldapsearch -H ldaps://gnome.darkhorse.com -v -x -b "dc=darkhorse,dc=com" '(uid=donaldr)' uid ... succeeds with: # donaldr, users, darkhorse.com dn: uid=donaldr,cn=users,dc=darkhorse,dc=com uid: donaldr # search result search: 2 result: 0 Success # numResponses: 2 # numEntries: 1 result: 0 Success (We are specifying "TLS_REQCERT never" in /etc/openldap/ldap.conf) Testing with openssl: openssl s_client -connect gnome.darkhorse.com:636 -showcerts -state ... succeeds: CONNECTED(00000003) SSL_connect:before/connect initialization SSL_connect:SSLv2/v3 write client hello A SSL_connect:SSLv3 read server hello A depth=1 /C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=Dark Horse Network/CN=DHC MIS Department verify error:num=19:self signed certificate in certificate chain verify return:0 SSL_connect:SSLv3 read server certificate A SSL_connect:SSLv3 read server done A SSL_connect:SSLv3 write client key exchange A SSL_connect:SSLv3 write change cipher spec A SSL_connect:SSLv3 write finished A SSL_connect:SSLv3 flush data SSL_connect:SSLv3 read finished A --- Certificate chain 0 s:/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=MIS/CN=gnome.darkhorse.com i:/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=Dark Horse Network/CN=DHC MIS Department 1 s:/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=Dark Horse Network/CN=DHC MIS Department i:/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=Dark Horse Network/CN=DHC MIS Department --- Server certificate -----BEGIN CERTIFICATE----- <deleted for brevity> -----END CERTIFICATE----- subject=/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=MIS/CN=gnome.darkhorse.com issuer=/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=Dark Horse Network/CN=DHC MIS Department --- No client certificate CA names sent --- SSL handshake has read 2640 bytes and written 325 bytes --- New, TLSv1/SSLv3, Cipher is AES256-SHA Server public key is 1024 bit Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : AES256-SHA Session-ID: D3F9536D3C64BAAB9424193F81F09D5C53B7D8E7CB5A9000C58E43285D983851 Session-ID-ctx: Master-Key: E224CC065924DDA6FABB89DBCC3E6BF89BEF6C0BD6E5D0B3C79E7DE927D6E97BF12219053BA2BB5B96EA2F6A44E934D3 Key-Arg : None Start Time: 1271202435 Timeout : 300 (sec) Verify return code: 0 (ok) So we believe that the slapd daemon is reading our certificate and writing it to LDAP clients. Apple Server Admin adds ProgramArguments ("-h ldaps:///") to /System/Library/LaunchDaemons/org.openldap.slapd.plist and TLSCertificateFile, TLSCertificateKeyFile, TLSCACertificateFile, and TLSCertificatePassphraseTool to /etc/openldap/slapd_macosxserver.conf when enabling SSL in the LDAP section of the Open Directory service. While that appears enough for LDAPS, it appears that this is not enough for TLS. Comparing our 10.6 and 10.5 slapd.conf and slapd_macosxserver.conf configuration files yields no clues. Replacing our certificate (generated with a self-signed ca) with an Apple Server Admin generated self signed certificate results in no change in ldapsearch results. Setting -d to 256 in /System/Library/LaunchDaemons/org.openldap.slapd.plist logs: 4/13/10 5:23:35 PM org.openldap.slapd[82162] conn=384 op=0 EXT oid=1.3.6.1.4.1.1466.20037 4/13/10 5:23:35 PM org.openldap.slapd[82162] conn=384 op=0 do_extended: unsupported operation "1.3.6.1.4.1.1466.20037" 4/13/10 5:23:35 PM org.openldap.slapd[82162] conn=384 op=0 RESULT tag=120 err=2 text=unsupported extended operation Any debugging advice much appreciated. -- Tom Kishel

  Read the article

• ESXI guests not using available CPU resources

  - by Alan M

  I have a VMWare ESXI 5.0.0 (it's a bit old, I know) host with three guest VMs on it. For reasons unknown, the guests will not use much of the availble CPU resources. I have all three guests in a single pool, with the hosts all configured to use the same amount of resource shares, so they're basically 33% each. The three guests are basically identically configured as far as their VM resources go. So the problem is, even when the guests are performing what should be very 'busy' activitites, such as at bootup, the actual host CPU consumed is something tiny, like 33mhz, when seen via vSphere console's "Virtual Machines" tab when viewing properties for the pool. And of course, the performance of the guest VMs is terrible. The host has plenty of CPU to spare. I've tried tinkering with individual guest VM resource settings; cranking up the reservation, etc. No matter. The guests just refuse to make use of the abundant CPU available to them, and insist on using a sliver of the available resources. Any suggestions? Update after reading various comments below Per the suggestions below, I did remove the guests from the application pool; this didn't make any difference. I do understand that the guests are not going to consume resources they do not need. I have tried to do a remote perfmon on the guest which is experiencing long boot times, but I cannot connect to the guest remotely with perfmon (guest is w2k8r2 server). Host graphs for CPU, Mem, Disk are basically flatlining; very little demand. Same is true for the guest stats; while the guest itself seems to be crawling, the guest resource graphing shows very little activity across CPU, Mem, Disk. Host is a Dell PowerEdge 2900, has 2 physical CPU,20gb RAM. (it's a test/dev environment using surplus gear) Guest1 has: VM ver. 7, 2vCPU, 4gb RAM, 140gb storage which lives on a RAID-5 array on the host. Guest2 has: VM ver. 7, 2vCPU, 4gb RAM, 140gb storage which lives on a RAID-5 array on the host. Guest3 has: VM ver. 7, 1vCPU, 2gb RAM, 2tb storage which lives on a RAID-5 ISCSI NAS box Perhaps I am making a false assumption that if a guest has a demand for CPU (e.g. Windows Task Manager shows 100% CPU), the host would supply the guest with more CPU (mem, disk) on demand. Another Update After checking the stats, it would appear that the host is indeed not busy at all, neither is the guest. I believe I have a good idea on the issue, though; a messed-up VMWare Tools install. The guest has VMware Tools on it, but the host says it does not. VMWare Tools refuses to uninstall, refuses to be upgraded, refuses to be recognized. While I cannot say with authority, this would appear to be something worth investigation. I do not know the origin of the guest itself, nor the specifics on the original VMWare Tools install. Following various bits of googling, I did come up with a few suggestions that went nowhere. To that end, I was going to delete this question, but was prompted not to do so since so many folks answered. My suspicion right now is; the problem truly is the guest; the guest is not making a demand on the host, and as a natural result, the host is treating the guest accordingly. My Final Update I am 99% certain the guest VM had something fundamentally wrong with it re VMWare Tools. I created a clone of a different VM with a near-identical OS config, but a properly working install of VMWare tools. The guest runs just great, and takes up it's allotment of resources when it needs to; e.g. it eats up about 850mhz CPU during startup, then ticks down to idle once the guest OS is stable.

  Read the article

• Riak "error":"insufficient_vnodes_available"

  - by Wolfiem

  We have 4 nodes Riak installation. They are running on Ubuntu 12.04 LTS Precise installed servers. We have installed 1.1.4 at August 1st 2012 and upgraded 1.2.0 when its available. Server names are: f1 - 10.10.0.12 - This is the first installed server. We have joined other ones to this server. This also serves Riak control. s2 - 10.10.0.22 - s3 - 10.10.0.23 - s4 - 10.10.0.24 - This server also serves Riak control. This morning we've seen "insufficient nodes available" error at our applications log and restarted all nodes. 3 of them became available except "f1" UPDATE : while I prepare this message live 3 nodes became unavailable and need restart Riak. wolfiem@f01:~$ sudo /etc/init.d/riak start Riak failed to start within 15 seconds, see the output of 'riak console' for more information. If you want to wait longer, set the environment variable WAIT_FOR_ERLANG to the number of seconds to wait. I've tried to set WAIT_FOR_ERLANG value to 60 seconds but I can't. adding this line in vm.args didn't work: -env WAIT_FOR_ERLANG 60 I also tried to set this from terminal but it didn't work either. wolfiem@f01:~$ export WAIT_FOR_ERLANG=60 It still says "Riak failed to start within 15 seconds" This is the console.log output: 2012-09-11 10:58:02.532 [info] <0.7.0> Application lager started on node '[email protected]' 2012-09-11 10:58:02.560 [warning] <0.148.0>@riak_core_ring_manager:reload_ring:231 No ring file available. 2012-09-11 10:58:02.585 [error] <0.164.0> CRASH REPORT Process <0.164.0> with 0 neighbours exited with reason: eaddrnotavail in gen_server:init_it/6 line 320 This is the error.log output 2012-09-11 10:58:02.585 [error] <0.164.0> CRASH REPORT Process <0.164.0> with 0 neighbours exited with reason: eaddrnotavail in gen_server:init_it/6 line 320 This is the crash.log output: 2012-09-11 10:58:02 =CRASH REPORT==== crasher: initial call: mochiweb_socket_server:init/1 pid: <0.164.0> registered_name: [] exception exit: {eaddrnotavail,[{gen_server,init_it,6,[{file,"gen_server.erl"},{line,320}]},{proc_lib,init_p_do_apply,3,[{file,"proc_lib.erl"},{line,227}]}]} ancestors: [riak_core_sup,<0.135.0>] messages: [] links: [<0.136.0>] dictionary: [] trap_exit: true status: running heap_size: 377 stack_size: 24 reductions: 403 neighbours: You can find the riak console output below: wolfiem@f01:~$ riak console Attempting to restart script through sudo -H -u riak Exec: /usr/lib/riak/erts-5.9.1/bin/erlexec -boot /usr/lib/riak/releases/1.2.0/riak -embedded -config /etc/riak/app.config -pa /usr/lib/riak/basho-patches -args_file /etc/riak/vm.args -- console Root: /usr/lib/riak Erlang R15B01 (erts-5.9.1) [source] [64-bit] [smp:8:8] [async-threads:64] [kernel-poll:true] =INFO REPORT==== 11-Sep-2012::10:44:18 === alarm_handler: {set,{system_memory_high_watermark,[]}} ** /usr/lib/riak/lib/observer-1.1/ebin/etop_txt.beam hides /usr/lib/riak/lib/basho-patches/etop_txt.beam ** Found 1 name clashes in code paths 10:44:19.099 [info] Application lager started on node '[email protected]' 10:44:19.130 [warning] No ring file available. 10:44:19.158 [error] CRASH REPORT Process <0.164.0> with 0 neighbours exited with reason: eaddrnotavail in gen_server:init_it/6 line 320 /usr/lib/riak/lib/os_mon-2.2.9/priv/bin/memsup: Erlang has closed. =INFO REPORT==== 11-Sep-2012::10:44:19 === alarm_handler: {clear,system_memory_high_watermark} Erlang has closed {"Kernel pid terminated",application_controller,"{application_start_failure,riak_core,{shutdown,{riak_core_app,start,[normal,[]]}}}"} Crash dump was written to: /var/log/riak/erl_crash.dump Kernel pid terminated (application_controller) ({application_start_failure,riak_core,{shutdown,{riak_core_app,start,[normal,[]]}}})

  Read the article

• No device file for partition on logical volume (Linux LVM)

  - by Brian

  I created a logical volume (scandata) containing a single ext3 partition. It is the only logical volume in its volume group (case4t). Said volume group is comprised by 3 physical volumes, which are three primary partitions on a single block device (/dev/sdb). When I created it, I could mount the partition via the block device /dev/mapper/case4t-scandatap1. Since last reboot the aforementioned block device file has disappeared. It may be of note -- I'm not sure -- that my superior (a college professor) had prompted this reboot by running sudo chmod -R [his name] /usr/bin, which obliterated all suid in its path, preventing the both of us from sudo-ing. That issue has been (temporarily) rectified via this operation. Now I'll cut the chatter and get started with the terminal dumps: $ sudo pvs; sudo vgs; sudo lvs Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Scanning for physical volume names PV VG Fmt Attr PSize PFree /dev/sdb1 case4t lvm2 a- 819.32G 0 /dev/sdb2 case4t lvm2 a- 866.40G 0 /dev/sdb3 case4t lvm2 a- 47.09G 0 Wiping internal VG cache Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Finding all volume groups Finding volume group "case4t" VG #PV #LV #SN Attr VSize VFree case4t 3 1 0 wz--n- 1.69T 0 Wiping internal VG cache Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Finding all logical volumes LV VG Attr LSize Origin Snap% Move Log Copy% Convert scandata case4t -wi-a- 1.69T Wiping internal VG cache $ sudo vgchange -a y Logging initialised at Sat Jan 8 11:43:14 2011 Set umask to 0077 Finding all volume groups Finding volume group "case4t" 1 logical volume(s) in volume group "case4t" already active 1 existing logical volume(s) in volume group "case4t" monitored Found volume group "case4t" Activated logical volumes in volume group "case4t" 1 logical volume(s) in volume group "case4t" now active Wiping internal VG cache $ ls /dev | grep case4t case4t $ ls /dev/mapper case4t-scandata control $ sudo fdisk -l /dev/case4t/scandata Disk /dev/case4t/scandata: 1860.5 GB, 1860584865792 bytes 255 heads, 63 sectors/track, 226203 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00049bf5 Device Boot Start End Blocks Id System /dev/case4t/scandata1 1 226203 1816975566 83 Linux $ sudo parted /dev/case4t/scandata print Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/case4t-scandata: 1861GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 1861GB 1861GB primary ext3 $ sudo fdisk -l /dev/sdb Disk /dev/sdb: 1860.5 GB, 1860593254400 bytes 255 heads, 63 sectors/track, 226204 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000081 Device Boot Start End Blocks Id System /dev/sdb1 1 106955 859116006 83 Linux /dev/sdb2 113103 226204 908491815 83 Linux /dev/sdb3 106956 113102 49375777+ 83 Linux Partition table entries are not in disk order $ sudo parted /dev/sdb print Model: DELL PERC 6/i (scsi) Disk /dev/sdb: 1861GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 880GB 880GB primary reiserfs 3 880GB 930GB 50.6GB primary 2 930GB 1861GB 930GB primary I find it a bit strange that partition one above is said to be reiserfs, or if it matters -- it was previously reiserfs, but LVM recognizes it as a PV. To reiterate, neither /dev/mapper/case4t-scandatap1 (which I had used previously) nor /dev/case4t/scandata1 (as printed by fdisk) exists. And /dev/case4t/scandata (no partition number) cannot be mounted: $sudo mount -t ext3 /dev/case4t/scandata /mnt/new mount: wrong fs type, bad option, bad superblock on /dev/mapper/case4t-scandata, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so All I get on syslog is: [170059.538137] VFS: Can't find ext3 filesystem on dev dm-0. Thanks in advance for any help you can offer, Brian P.S. I am on Ubuntu GNU/Linux 2.6.28-11-server (Jaunty) (out of date, I know -- that's on the laundry list).

  Read the article

• Blocking 'good' bots in nginx with multiple conditions for certain off-limits URL's where humans can go

  - by Glenn Plas

  After 2 days of searching/trying/failing I decided to post this here, I haven't found any example of someone doing the same nor what I tried seems to be working OK. I'm trying to send a 403 to bots not respecting the robots.txt file (even after downloading it several times). Specifically Googlebot. It will support the following robots.txt definition. User-agent: * Disallow: /*/*/page/ The intent is to allow Google to browse whatever they can find on the site but return a 403 for the following type of request. Googlebot seems to keep on nesting these links eternally adding paging block after block: my_domain.com:80 - 66.x.67.x - - [25/Apr/2012:11:13:54 +0200] "GET /2011/06/ page/3/?/page/2//page/3//page/2//page/3//page/2//page/2//page/4//page/4//pag e/1/&wpmp_switcher=desktop HTTP/1.1" 403 135 "-" "Mozilla/5.0 (compatible; G ooglebot/2.1; +http://www.google.com/bot.html)" It's a wordpress site btw. I don't want those pages to show up, even though after the robots.txt info got through, they stopped for a while only to begin crawling again later. It just never stops .... I do want real people to see this. As you can see, google get a 403 but when I try this myself in a browser I get a 404 back. I want browsers to pass. root@my_domain:# nginx -V nginx version: nginx/1.2.0 I tried different approaches, using a map and plain old nono if's and they both act the same: (under http section) map $http_user_agent $is_bot { default 0; ~crawl|Googlebot|Slurp|spider|bingbot|tracker|click|parser|spider 1; } (under the server section) location ~ /(\d+)/(\d+)/page/ { if ($is_bot) { return 403; # Please respect the robots.txt file ! } } I recently had to polish up my Apache skills for a client where I did about the same thing like this : # Block real Engines , not respecting robots.txt but allowing correct calls to pass # Google RewriteCond %{HTTP_USER_AGENT} ^Mozilla/5\.0\ \(compatible;\ Googlebot/2\.[01];\ \+http://www\.google\.com/bot\.html\)$ [NC,OR] # Bing RewriteCond %{HTTP_USER_AGENT} ^Mozilla/5\.0\ \(compatible;\ bingbot/2\.[01];\ \+http://www\.bing\.com/bingbot\.htm\)$ [NC,OR] # msnbot RewriteCond %{HTTP_USER_AGENT} ^msnbot-media/1\.[01]\ \(\+http://search\.msn\.com/msnbot\.htm\)$ [NC,OR] # Slurp RewriteCond %{HTTP_USER_AGENT} ^Mozilla/5\.0\ \(compatible;\ Yahoo!\ Slurp;\ http://help\.yahoo\.com/help/us/ysearch/slurp\)$ [NC] # block all page searches, the rest may pass RewriteCond %{REQUEST_URI} ^(/[0-9]{4}/[0-9]{2}/page/) [OR] # or with the wpmp_switcher=mobile parameter set RewriteCond %{QUERY_STRING} wpmp_switcher=mobile # ISSUE 403 / SERVE ERRORDOCUMENT RewriteRule .* - [F,L] # End if match This does a bit more than I asked nginx to do but it's about the same principle, I'm having a hard time figuring this out for nginx. So my question would be, why would nginx serve my browser a 404 ? Why isn't it passing, The regex isn't matching for my UA: "Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/536.5 (KHTML, like Gecko) Chrome/19.0.1084.30 Safari/536.5" There are tons of example to block based on UA alone, and that's easy. It also looks like the matchin location is final, e.g. it's not 'falling' through for regular user, I'm pretty certain that this has some correlation with the 404 I get in the browser. As a cherry on top of things, I also want google to disregard the parameter wpmp_switcher=mobile , wpmp_switcher=desktop is fine but I just don't want the same content being crawled multiple times. Even though I ended up adding wpmp_switcher=mobile via the google webmaster tools pages (requiring me to sign up ....). that also stopped for a while but today they are back spidering the mobile sections. So in short, I need to find a way for nginx to enforce the robots.txt definitions. Can someone shell out a few minutes of their lives and push me in the right direction please ? I really appreciate ANY response that makes me think harder ;-)

  Read the article

• Python in command line runs the wrong version?

  - by Deflect

  I have several versions of Python installed on a Windows 7 computer. I want to run Python 2.7 by default, but for whatever reason, typing python in the command line runs Python version 2.4.5. I've tried adding C:\Python27 to my system path variable as per this question, and manually combed my path variable it to make sure Python 2.4.5 wasn't tossed in there by mistake, but that didn't fix the issue. I have to type in C:\Python27\python.exe every time I want to access the correct version of python I want. What other places can I check? How can I make the command line use the correct version of python? I also found this but it's not for windows. [EDIT] My path (separated by semicolons): C:\Program Files\Common Files\Microsoft Shared\Windows Live; C:\Program Files (x86)\Common Files\Microsoft Shared\Windows Live; C:\Windows\system32; C:\Windows; C:\Windows\System32\Wbem; C:\Windows\System32\WindowsPowerShell\v1.0\; C:\Program Files\Dell\DW WLAN Card\Driver; C:\Program Files (x86)\Common Files\Roxio Shared\DLLShared\; C:\Program Files (x86)\Windows Live\Shared; c:\Program Files (x86)\Microsoft SQL Server\100\Tools\Binn\; c:\Program Files\Microsoft SQL Server\100\Tools\Binn\; c:\Program Files\Microsoft SQL Server\100\DTS\Binn\; C:\Program Files\TortoiseGit\bin; C:\Program Files\Java\jdk1.6.0_26\bin; C:\Program Files\Java\jdk1.6.0_21 ; C:\Program Files\IVI Foundation\VISA\Win64\Bin\; C:\Program Files (x86)\IVI Foundation\VISA\WinNT\Bin\; C:\Program Files (x86)\IVI Foundation\VISA\WinNT\Bin; C:\Program Files\WPIJavaCV\OpenCV_2.2.0\bin; C:\Program Files (x86)\LilyPond\usr\bin; C:\Program Files\TortoiseSVN\bin; C:\Program Files (x86)\doxygen\bin; C:\Program Files (x86)\Graphviz 2.28\bin; C:\Users\Michael\bin\Misc\cppcheck\; C:\Program Files (x86)\Git\cmd; C:\Python27\python.exe; C:\Ruby192\bin; C:\Users\Michael\AppData\Roaming\cabal\bin; C:\Python27\; [EDIT 2] Running python spews this out: 'import site' failed; used -v for traceback Python 2.4.5 (#1, Jul 22 2011, 02:01:04) [GCC 4.1.1] on mingw32 Type "help", "copyright", "credits" or "license" for more information. >>> ...and running python --version (as suggested below) seems to be an unrecognized option. (I also tried running python -v, and it appears that Python 2.4 is trying to import libraries from C:\Python27\Lib, and failed due to a syntax error when it encountered a with statement, which was added in later version, I think) Also, I'm not sure if it's significant or not, but the above python version says something about GCC and mingw32, while running C:\python27\python.exe shows this: Python 2.7.2 (default, Jun 12 2011, 15:08:59) [MSC v.1500 32 bit (Intel)] on win32 Type "help", "copyright", "credits" or "license" for more information. >>>>

  Read the article

• Understanding NFS4 (Linux server)

  - by drumfire

  I've been a bit bothered by NFS4 on Linux. Some information 'out there' seems to conflict with other information, and other information appears hard to find. So here are a couple of things that caught my attention, hopefully someone out there can shed some light on this. This question focuses exclusively on NFS4 without Kerberos etc. 1. Exports There is ambiguous information in the exports manpage on the structure of /etc/exports. To quote from exports(5): Also, each line may have one or more specifications for default options after the path name, in the form of a dash ("-") followed by an option list. The option list is used for all subsequent exports on that line only. What does "subsequent exports on that line only" mean? 1.2 fsid=0 not required anymore? I was searching for fsid when I found a comment on the linux-nfs list stating fsid=0 is not required anymore. Now I'm just confused, do I need it with nfs4 or not?! 2. Non-exported directory still mountable Say I have the following tree: /exp /exp/users /exp/distr /exp/distr/archlinux /exp/distr/debian And I have the following entries in this fstab entry: /dev/disk/by-label/users /mnt/users ext4 defaults 0 0 /dev/disk/by-label/distr /mnt/distr ext4 defaults 0 0 /mnt/users /exp/users none bind 0 0 /mnt/distr /exp/distr none bind 0 0 And my exports is exactly this: /exp 192.168.1.0/24(fsid=0,rw,async,no_subtree_check,no_root_squash) /exp/distr 192.168.1.0/24(rw,async,no_subtree_check,no_root_squash) And exportfs -arv shows: exporting 192.168.1.0/24:/exp/distr exporting 192.168.1.0/24:/exp Then why am I able to do this and get no error on a client: mount -t nfs4 server:/exp/users /tmp/test Even though /exp/users is not exported? I didn't export this directory, and while I don't see the contents of /dev/disk/by-label/users unless I specify crossmnt, I am still able to write to the directory. Everything I write to there goes to the underlying directory of /exp/users which can be seen when I umount /exp/users; ls /exp/users.. 3. The odd case of showmount -d server As stated by rpc.mountd(8), this command should display directories that are either currently mounted by clients, or stale entries in /var/lib/nfs/rmtab, as can be read: The rpc.mountd daemon registers every successful MNT request by adding an entry to the /var/lib/nfs/rmtab file. When receivng a UMNT request from an NFS client, rpc.mountd simply removes the matching entry from /var/lib/nfs/rmtab, as long as the access control list for that export allows that sender to access the export. (...) Note, however, that there is little to guarantee that the contents of /var/lib/nfs/rmtab are accurate. A client may continue accessing an export even after invoking UMNT. If the client reboots without sending a UMNT request, stale entries remain for that client in /var/lib/nfs/rmtab. After reading this I surely wonder: Isn't it terribly insecure to just expose this type of client information; Aren't unaware server admins bound to have an rmtab with a lot of stale clients; Is this the reason that clients that mount nfs4 directories with mount -v get to see output like "nothing was mounted" even though something was mounted? I have a lot of other questions regarding nfs4, but I'll keep it at this for the moment.. :)

  Read the article

• how does openvpn decide which interface to get IP addrs from

  - by bkrupa

  Using ubuntu 10.04 on both ends. We have a client and server machine on the SAME network attempting to make a vpn connection. We use the config files from here and made minimal changes. The server and client start and seem to connect without any trouble. The server looks like: Wed Feb 23 22:13:22 2011 MULTI: multi_create_instance called Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Re-using SSL/TLS context Wed Feb 23 22:13:22 2011 192.168.1.55:47166 LZO compression initialized Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Control Channel MTU parms [ L:1574 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Data Channel MTU parms [ L:1574 D:1450 EF:42 EB:135 ET:32 EL:0 AF:3/1 ] Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Local Options hash (VER=V4): 'f7df56b8' Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Expected Remote Options hash (VER=V4): 'd79ca330' Wed Feb 23 22:13:22 2011 192.168.1.55:47166 TLS: Initial packet from 192.168.1.55:47166, sid=69112e42 5458135b *...* Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Feb 23 22:13:22 2011 192.168.1.55:47166 [client1] Peer Connection Initiated with 192.168.1.55:47166 On the client side the connection looks like: Wed Feb 23 22:20:07 2011 [server] Peer Connection Initiated with [AF_INET]192.168.1.41:1194 Wed Feb 23 22:20:10 2011 SENT CONTROL [server]: 'PUSH_REQUEST' (status=1) Wed Feb 23 22:20:10 2011 PUSH: Received control message: 'PUSH_REPLY,route-gateway 10.8.0.4,ping 10,ping-restart 120,ifconfig 10.8.0.50 255.255.255.0' ... Wed Feb 23 22:20:10 2011 /sbin/ifconfig tap0 10.8.0.50 netmask 255.255.255.0 mtu 1500 broadcast 10.8.0.255 Wed Feb 23 22:20:10 2011 Initialization Sequence Completed The openvpn server has been configured to assign ip addresses in the range 10.8.0.* and the client has been given 10.8.0.50. When I run the following nmap from the client: Starting Nmap 5.00 ( http://nmap.org ) at 2011-02-23 22:04 EST Host 10.8.0.50 is up (0.00047s latency). Nmap done: 256 IP addresses (1 host up) scanned in 30.34 seconds Host 192.168.1.1 is up (0.0025s latency). Host 192.168.1.18 is up (0.074s latency). Host 192.168.1.41 is up (0.0024s latency). Host 192.168.1.55 is up (0.00018s latency). Nmap done: 256 IP addresses (4 hosts up) scanned in 6.33 seconds If I run an nmap from the server on 10.8.0.* I get nothing. If the client has two interfaces (wireless and tap device) when you look for a certain ip address, how does it decide which interface to connect on? edit I am trying to set up a vpn so that I can connect to my home network from a remote network. It seems like openvpn is connecting but none of the computers on my home network appear as network machines even after the connection is "Established". Stripped versions of the client and server config files are posted below. Thanks for any help you can offer. server.conf port 1194 proto udp dev tap ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/server.crt key /etc/openvpn/easy-rsa/keys/server.key # This file should be kept secret dh /etc/openvpn/easy-rsa/keys/dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 client.conf client dev tap dev-node tap0901 proto udp remote ********** 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client1.crt key client1.key comp-lzo verb 3 one other thing that might be helpful, I tried to connect using the openvpn gui for windows and the connection stalls out on "obtaining configuration" and the bar just scrolls forever.

  Read the article

• How to diagnose computer lockup/freezing problem

  - by Scott Mitchell

  I built a desktop computer a couple years back with the following specs: CPU: Intel Core 2 Quad Q9300 Yorkfield 2.5GHz 6MB L2 Cache LGA 775 95W Quad-Core Processor BX80580Q9300 Motherboard: EVGA 122-CK-NF68-T1 LGA 775 NVIDIA nForce 680i SLI ATX Intel Motherboard Video Card: Two EVGA 256-P2-N758-TR GeForce 8600GT SCC 256MB 128-bit GDDR3 PCI Express x16 SLI Supported Video Card PSU: SeaSonic S12 Energy Plus SS-550HT 550W ATX12V V2.3 / EPS12V V2.91 SLI Certified CrossFire Ready 80 PLUS Certified Active PFC Power Supply Memory: Two G.SKILL 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model F2-6400CL5D-4GBPQ Since its inception, the machine has periodically locked up, the regularlity having varied over the years from once a day to once a month. Typically, lockups happen once every few days. By "lockup" I mean my computer just freezes. The screen locks up, I can't move the mouse. Hitting keys on my keyboard that normally turn LEDs on or off on the keyboard (such as Caps Lock) no longer turn the LEDs on or off. If there was music playing at the time of the lockup, noise keeps coming out of the speakers, but it's just the current frequency/note that plays indefinitely. There is no BSOD. When such a lockup occurs I have to do a hard reboot by either turning off the computer or hitting the reset button. I have the most recent version of the NVIDIA hardware drivers, and update them semi-regularly, but that hasn't seemed to help. I am currently using Windows 7 x64, but was previously using Windows Server 2003 x64 and having the same lockup issues. My guess is that it's somehow video driver or motherboard related, but I don't know how to go about diagnosing this problem to narrow down which of the two is the culprit. Additional information re: cooling Regarding cooling... I've not installed any after-market cooling systems aside from two regular fans I scavenged from an older computer. The fan atop the CPU is the one that shipped with it. One of the two scavenged fans I added it located at the bottom tower of the corner, in an attempt to create some airflow from front to back. The second fan is pointed directly at the two video cards. SpeedFan installation and readings Per studiohack's suggestion, I installed SpeedFan, which provided the following temperature readings: GPU: 63C GPU: 65C System: 76C CPU: 64C AUX: 36C Core 0: 78C Core 1: 76C Core 2: 79C Core 3: 79C Update #3: Another Lockup :-( Well, I had another lockup last night. :-( SpeedFan reported the CPU temp at 38 C when it happened, and there was no spike in temperature leading up to the freeze. One thing I notice is that the freeze seems more likely to happen if I am watching a video. In fact, of the last 5 freezes over the past month, 4 of them have been while watching a video on Flickr. Not necessarily the same video, but a video nevertheless. I don't know if this is just coincidence or if it means anything. (As an aside, each night before bedtime my 2 year old daughter sits on my lap and watches some home videos on Flickr and, in the last month, has learned the phrase, "Uh oh, computer broke.") Update #4: MemTest86 and 3DMark06 Test Results: Per suggestions in the comments, I ran the MemTest86 overnight and it cycled through the 8 GB of memory 5 times without error. I also ran the 3DMark06 test without a problem (see my scores at http://3dmark.com/3dm06/15163549). So... what now? :-) Any further suggestions on what to check? Is there some way to get a stack trace or something when the computer locks like that? Thanks

  Read the article

• Cisco ASA not forwarding traffic from one interface to another

  - by Antoine Benkemoun

  Hello ServerFault, I am needing help in the configuration process of my Cisco ASA 5510. I have set up 4 Cisco ASA interconnected together via a big LAN. Each Cisco ASA has 3 or 4 LANs attached to them. The IP routing part is taken care of by OSPF. My problem is on another level. A computer connected to one of the LANs attached to an ASA has no problem communicating with the outside world. The outside world being anything "after" the ASA. My problem is that I am completely unable to have them communicate with another LAN connected to the same ASA. To rephrase this, I am unable to send traffic from one interface of a given ASA to another interface of the same ASA. My configuration is the following : ! hostname Fuji ! interface Ethernet0/0 speed 100 duplex full nameif outside security-level 0 ip address 10.0.0.2 255.255.255.0 no shutdown ! interface Ethernet0/1 speed 100 duplex full nameif cs4 no shutdown security-level 100 ip address 10.1.4.1 255.255.255.0 ! interface Ethernet0/2 speed 100 duplex full no shutdown ! interface Ethernet0/2.15 vlan 15 nameif cs5 security-level 100 ip address 10.1.5.1 255.255.255.0 ! interface Ethernet0/2.16 vlan 16 nameif cs6 security-level 100 ip address 10.1.6.1 255.255.255.0 ! interface Management0/0 speed 100 duplex full nameif management security-level 100 ip address 10.6.0.252 255.255.255.0 ! access-list nat_cs4 extended permit ip 10.1.4.0 255.255.255.0 any access-list acl_cs4 extended permit ip 10.1.4.0 255.255.255.0 any access-list nat_cs5 extended permit ip 10.1.5.0 255.255.255.0 any access-list acl_cs5 extended permit ip 10.1.5.0 255.255.255.0 any access-list nat_cs6 extended permit ip 10.1.6.0 255.255.255.0 any access-list acl_cs6 extended permit ip 10.1.6.0 255.255.255.0 any ! access-list nat_outside extended permit ip any any access-list acl_outside extended permit ip any 10.1.4.0 255.255.255.0 access-list acl_outside extended permit ip any 10.1.5.0 255.255.255.0 access-list acl_outside extended permit ip any 10.1.6.0 255.255.255.0 ! nat (outside) 0 access-list nat_outside nat (cs4) 0 access-list nat_cs4 nat (cs5) 0 access-list nat_cs5 nat (cs6) 0 access-list nat_cs6 ! static (outside,cs4) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 static (outside,cs5) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 static (outside,cs6) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 ! static (cs4,outside) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 static (cs4,cs5) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 static (cs4,cs6) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 ! static (cs5,outside) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 static (cs5,cs4) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 static (cs5,cs6) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 ! static (cs6,outside) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 static (cs6,cs4) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 static (cs6,cs5) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 ! access-group acl_outside in interface outside access-group acl_cs4 in interface cs4 access-group acl_cs5 in interface cs5 access-group acl_cs6 in interface cs6 ! router ospf 1 network 10.0.0.0 255.255.255.0 area 1 network 10.1.4.0 255.255.255.0 area 1 network 10.1.5.0 255.255.255.0 area 1 network 10.1.6.0 255.255.255.0 area 1 log-adj-changes ! There is nothing really complicated in this configuration. It just NATs from one interface to another and that's it. I have tried enabling same-security-traffic permit inter-interface but that doesn't help. I therefore must be missing something a little bit more complicated. Does anyone know why I cannot foward traffic from one interface to another ? Thank you in advance for your help, Antoine

  Read the article

• apache2 namevirtualhost resolving wrong site

  - by joe

  Running apache 2.2.6. I'm setting up a development environment. dev and production will be hosted on the same machine, same IP address. DNS entries like prod.domain.com and dev.domain.com point to the same IP. * Imprortant: it is required that dev and prod are otherwise completely separate. Each will run it's own apache instance. Each will use it's own apache configuration. Each, prod and dev, will host http and https. I have this set up and working, but not as restrictive as I'd like. For instance, the production config: NameVirtualHost *:80 NameVirtualHost *:443 <VirtualHost *:80 > ServerName prod.domain.com # ... etc </VirtualHost> <VirtualHost *:443 > ServerName prod.domain.com # ... etc </VirtualHost> The dev site is set up similarly, using ports 8080 and 4443. Each site works fine. But assuming both apaches are running, one can also hit "cross-site" by mistake. So, inadvertently hitting prod.domain.com:8080 successfully returns a page from the dev site. It would be much better if this failed completely. This is a bit more difficult to solve (for me) because of the need for two apache configs. If all in one, the single process would have full knowledge of everything. So, I tried to solve this with brute force, including virtual hosts for the "other" site, with something that would fail, like no access to documentroot. But apache then inexplicably finds the "wrong" virtual host. Here's the full config for production, with the dummy dev configs. NameVirtualHost *:80 NameVirtualHost *:443 # ---------------------------------------------- # DUMMY HOSTS <VirtualHost *:8080 > ServerName dev.domain.com:8080 DocumentRoot /tmp/ <Directory /tmp/ > Order deny,allow Deny from all </Directory> </VirtualHost> <VirtualHost *:4443 > ServerName dev.domain.com:4443 DocumentRoot /tmp/ <Directory /tmp/ > Order deny,allow Deny from all </Directory> </VirtualHost> # ---------------------------------------------- # REAL PRODUCTION HOSTS <VirtualHost *:80 > ServerName prod.domain.com:80 DocumentRoot /something/valid/ <Directory /something/valid/> Order allow,deny Allow from all </Directory> </VirtualHost> <VirtualHost *:443 > ServerName prod.domain.com:443 DocumentRoot /something/valid/ <Directory /something/valid/> Order allow,deny Allow from all </Directory> # .... other valid ssl setup </VirtualHost> Here's the strange thing. With this configuration, a prod.domain.com:80 hit succeeds. But a prod.domain.com:443 hit fails, because it finds the dev.domain.com:4443 instead. I've also tried removing the port from the ServerName, but it still doesn't work. Sorry for the long question. Hopefully this is enough information. Thanks in advance for any help.

  Read the article

• Linux bcm43224 wifi adapter slows down a couple minutes after boot

  - by Blubber

  I just installed Ubuntu on my mid 2012 MacBook Air. Everything worked out of the box, but the wifi is showing some weird behavior. When I first login it's really fast, loading google.com is near instant, and browsing in general feels at least as smooth as it did on Mac OS. However, after a couple minutes the connection slows down dramatically, sometimes it takes over 5s to load google.com, a simple reboot fixes the problem for another couple minutes. Specs: Wifi: 02:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01) Driver: open-source brcmsmac driver Kernel: Linux wega 3.8.0-21-generic #32-Ubuntu SMP Tue May 14 22:16:46 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux Distro: Ubuntu 13.04 (uptodate) I tried a number of things, none of which actually helped Use proprietary sta driver from broadcom Installed firmware into /lib/firmware/brcms (which, as far as I can tell from logs, does not get loaded at all) Switch router to only use 2.4 OR 5 GHz Set router to only use a OR g OR n Set router to use AES encryption only Turned off power management on the adapter Set regulatory region to the correct value (NL) on both router and laptop Disable ipv6 Nothing seems to help, the slowdown always occurs. I did notice that the latency (ping google.com) stays roughly the same (around 9ms). Below is some more information that might be of use. $ lspci -nnk | grep -iA2 net 02:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) Subsystem: Apple Inc. Device [106b:00e9] Kernel driver in use: bcma-pci-bridge $ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no $ lsmod Module Size Used by dm_crypt 22820 1 arc4 12615 2 brcmsmac 550698 0 coretemp 13355 0 kvm_intel 132891 0 parport_pc 28152 0 kvm 443165 1 kvm_intel ppdev 17073 0 cordic 12574 1 brcmsmac brcmutil 14755 1 brcmsmac mac80211 606457 1 brcmsmac cfg80211 510937 2 brcmsmac,mac80211 bnep 18036 2 rfcomm 42641 12 joydev 17377 0 applesmc 19353 0 input_polldev 13896 1 applesmc snd_hda_codec_hdmi 36913 1 microcode 22881 0 snd_hda_codec_cirrus 23829 1 nls_iso8859_1 12713 1 uvcvideo 80847 0 btusb 22474 0 snd_hda_intel 39619 3 videobuf2_vmalloc 13056 1 uvcvideo snd_hda_codec 136453 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec_cirrus bcm5974 17347 0 bluetooth 228619 22 bnep,btusb,rfcomm snd_hwdep 13602 1 snd_hda_codec lpc_ich 17061 0 videobuf2_memops 13202 1 videobuf2_vmalloc videobuf2_core 40513 1 uvcvideo videodev 129260 2 uvcvideo,videobuf2_core bcma 41051 1 brcmsmac snd_pcm 97451 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30180 1 snd_seq_midi snd_seq 61554 2 snd_seq_midi_event,snd_seq_midi snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi snd_timer 29425 2 snd_pcm,snd_seq snd 68876 16 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_hda_codec_cirrus mei 41158 0 soundcore 12680 1 snd apple_bl 13673 0 mac_hid 13205 0 lp 17759 0 parport 46345 3 lp,ppdev,parport_pc usb_storage 57204 0 hid_apple 13237 0 hid_generic 12540 0 ghash_clmulni_intel 13259 0 aesni_intel 55399 399 aes_x86_64 17255 1 aesni_intel xts 12885 1 aesni_intel lrw 13257 1 aesni_intel gf128mul 14951 2 lrw,xts ablk_helper 13597 1 aesni_intel cryptd 20373 4 ghash_clmulni_intel,aesni_intel,ablk_helper i915 600351 3 ahci 25731 3 libahci 31364 1 ahci video 19390 1 i915 i2c_algo_bit 13413 1 i915 drm_kms_helper 49394 1 i915 usbhid 47074 0 drm 286313 4 i915,drm_kms_helper hid 101002 3 hid_generic,usbhid,hid_apple $ dmesg | egrep 'b43|bcma|brcm|[F]irm' [ 0.055025] [Firmware Bug]: ioapic 2 has no mapping iommu, interrupt remapping will be disabled [ 0.152336] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 2.187681] pci_root PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-99] only partially covers this bridge [ 12.553600] bcma-pci-bridge 0000:02:00.0: enabling device (0000 -> 0002) [ 12.553657] bcma: bus0: Found chip with id 0xA8D8, rev 0x01 and package 0x08 [ 12.553688] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0) [ 12.553715] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0) [ 12.553764] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0) [ 12.605777] bcma: bus0: Bus registered [ 12.852925] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 17 [ 13.085176] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: false (implement) [ 13.085186] brcmsmac bcma0:0: brcms_ops_config: change power-save mode: false (implement) [ 20.862617] brcmsmac bcma0:0: brcmsmac: brcms_ops_bss_info_changed: associated [ 20.862622] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 0 (implement) [ 20.862625] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 20.897957] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"wlan" Mode:Managed Frequency:5.22 GHz Access Point: E0:46:9A:4E:63:9A Bit Rate=65 Mb/s Tx-Power=17 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=63/70 Signal level=-47 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:13 Invalid misc:56 Missed beacon:0

  Read the article

• Ubuntu 10.04: OpenVZ Kernel and pure-ftpd issues on HOST (no guest setup yet)

  - by Seidr

  After compiling and installing the OpenVZ flavour of kernel under Ubuntu 10.04, I am unable to browse to certain directories when connecting to the pure-ftpd server. The clients are dropping into PASSIVE mode, which is fine. This behaviour was happening before the change of kernel, however now when I browse to certain directories the connection just gets dropped. This only happens with a few directories under one login (web in specific), where as with another login it happens as soon as I connect. I've got the nf_conntrack_ftp kernel module installed (required to keep track of passive FTP connections as I understand, and an alias of the ip_conntrack_ftp module), however this has provided no alleviation of my problem. This module was actually required upon initial setup of my OS to get passive FTP working correctly, however when I compiled the OpenVZ kernel a lot of these modules were missing (iptables, conntrack etc). I recompiled the kernel with the missing modules, but to no effect. I've turned verbosity for the pure-ftpd server up, and still no clues have been spotted in either syslog or the transfer log. Neither did an strace provide any clues (that I could discern anyway) - although one strange thing is both in the output to the client and in the strace I notice that it does infact probe the directory and return the number of matches - it just fails after that. One more thing to mention is that if I FTP using the same credentials locally, everything works fine. This suggests that it is in fact an issue with either the conntrack_ftp module not functioning as expected, or a deeper networking issue. The Kernel was compiled and installed following the instructions at https://help.ubuntu.com/community/OpenVZ - bar the changes to the Kernel configuration (such as add iptables as a module). Below is an example of the log sent to the data (under FileZilla). Status: Resolving address of xxxx.co.uk Status: Connecting to 78.46.xxx.xxx:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [privsep] [TLS] ---------- Response: 220-You are user number 4 of 10 allowed. Response: 220-Local time is now 08:52. Server port: 21. Response: 220-This is a private system - No anonymous login Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 15 minutes of inactivity. Command: USER xxx Response: 331 User xxx OK. Password required Command: PASS ******** Response: 230-User xxx has group access to: client1 sshusers Response: 230 OK. Current restricted directory is / Command: OPTS UTF8 ON Response: 200 OK, UTF-8 enabled Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is your current location Status: Directory listing successful Status: Retrieving directory listing... Command: CWD /web Response: 250 OK. Current directory is /web Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PORT 10,0,2,30,14,143 Response: 500 I won't open a connection to 10.0.2.30 (only to 188.220.xxx.xxx) Command: PASV Response: 227 Entering Passive Mode (78,46,79,147,234,110) Command: MLSD Response: 150 Accepted data connection Response: 226-ASCII Response: 226-Options: -a -l Response: 226 57 matches total Error: Could not read from transfer socket: ECONNRESET - Connection reset by peer Error: Failed to retrieve directory listing Any suggestions please? I'm willing to try anything!

  Read the article

• Is Apache 2.2.22 able to sustain 1.000 simultaneous connected clients?

  - by Fnux

  For an article in a news paper, I'm benchmarking 5 different web servers (Apache2, Cherokee, Lighttpd, Monkey and Nginx). The tests made consist of measuring the execution times as well as different parameters such as the number of request served per second, the amount of RAM, the CPU used, during a growing load of simultaneous clients (from 1 to 1.000 with a step of 10) each client sending 1.000.000 requets of a small fixed file, then of a medium fixed file, then a small dynamic content (hello.php) and finally a complex dynamic content (the computation of the reimbursment of a loan). All the web servers are able to sustain such a load (up to 1.000 clients) but Apache2 which always stops to respond when the test reach 450 to 500 simultaneous clients. My configuration is : CPU: AMD FX 8150 8 cores @ 4.2 GHz RAM: 32 Gb. SSD: 2 x Crucial 240 Gb SATA6 OS: Ubuntu 12.04.3 64 bit WS: Apache 2.2.22 My Apache2 configuration is as follows: /etc/apache2/apache2.conf LockFile ${APACHE_LOCK_DIR}/accept.lock PidFile ${APACHE_PID_FILE} Timeout 30 KeepAlive On MaxKeepAliveRequests 1000000 KeepAliveTimeout 2 ServerName "fnux.net" <IfModule mpm_prefork_module> StartServers 16 MinSpareServers 16 MaxSpareServers 16 ServerLimit 2048 MaxClients 1024 MaxRequestsPerChild 0 </IfModule> User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> DefaultType None HostnameLookups Off ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel emerg Include mods-enabled/*.load Include mods-enabled/*.conf Include httpd.conf Include ports.conf LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include conf.d/ Include sites-enabled/ /etc/apache2/ports.conf NameVirtualHost *:8180 Listen 8180 <IfModule mod_ssl.c> Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> /etc/apache2/mods-available <IfModule mod_fastcgi.c> AddHandler php5-fcgi .php Action php5-fcgi /cgi-bin/php5.external <Location "/cgi-bin/php5.external"> Order Deny,Allow Deny from All Allow from env=REDIRECT_STATUS </Location> </IfModule> /etc/apache2/sites-available/default <VirtualHost *:8180> ServerAdmin webmaster@localhost DocumentRoot /var/www/apache2 <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel emerg ##### CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> <IfModule mod_fastcgi.c> AddHandler php5-fcgi .php Action php5-fcgi /php5-fcgi Alias /php5-fcgi /usr/lib/cgi-bin/php5-fcgi FastCgiExternalServer /usr/lib/cgi-bin/php5-fcgi -host 127.0.0.1:9000 -pass-header Authorization </IfModule> </VirtualHost> /etc/security/limits.conf * soft nofile 1000000 * hard nofile 1000000 So, I would trully appreciate your advice to setup Apache2 to make it able to sustain 1.000 simultaneous clients, if this is even possible. TIA for your help. Cheers.

  Read the article

• Tuning performance of Ubuntu 10.04 on Compaq Evo W4000.

  - by Fantomas

  Hi, I got this computer free and installed Ubuntu 10.04 on it + updates, plus followed the following tutorial all the way: http://www.unixmen.com/linux-tutorials/937-things-to-do-after-installing-ubuntu-1004-lts-lucid-lynx I love the Docky which comes with it, but the computer has been running rather slowly. The System: kernel 2.6.32-22-generic Gnome 2.30.0 (I like Gnome!) Memory: 1GB Processor: Intel (R) Pentium (R) 4 CPU 1700 MHz (needless to say, it is 32 bit). I think I dedicated 128 Mb to video memory while installing, but cannot find this setting now. I did also install an NVidia driver for the 3D card, so I probably want to reclaim that memory back. I want to trim the fat but I also want to keep some of the sex appeal of Ubuntu 10.04. I will gift this computer to a friend, who will use it for Internet, music, videos, word processing, Skype and instant messaging - he is non-technical, so this hardware and Linux should work for him; I just need to speed it up while keeping the good software and having a nice UI. I sort of know my way around Linux, but not that well. Feel free to ask me to run particular commands if you want more info. For starters, here are the services below. Which ones can I kill and how? What else can go? There is no need to run ssh or ftp or http or ntp servers. As I said before, this computer is for non-technical person. There is also absolutely no bluetooth or wireless networking needed - it will feed off a regular ethernet cable. What I do not want to do is reinstall some other distro or recompile a kernel. I want to make it 80% perfect spending 20% of the energy :) Thanks! $ service --status-all [ ? ] acpi-support [ ? ] acpid [ ? ] alsa-mixer-save [ ? ] anacron [ - ] apparmor [ ? ] apport [ ? ] atd [ ? ] avahi-daemon [ ? ] binfmt-support [ - ] bluetooth [ - ] bootlogd [ - ] brltty [ ? ] console-setup [ ? ] cron [ + ] cups [ ? ] dbus [ ? ] dmesg [ ? ] dns-clean [ ? ] failsafe-x [ - ] fancontrol [ ? ] gdm [ - ] grub-common [ ? ] hostname [ ? ] hwclock [ ? ] hwclock-save [ ? ] irqbalance [ - ] kerneloops [ ? ] killprocs [ - ] lm-sensors [ ? ] module-init-tools [ ? ] network-interface [ ? ] network-interface-security [ ? ] network-manager [ ? ] networking [ ? ] ondemand [ ? ] pcmciautils [ ? ] plymouth [ ? ] plymouth-log [ ? ] plymouth-splash [ ? ] plymouth-stop [ ? ] pppd-dns [ ? ] procps [ + ] pulseaudio [ ? ] rc.local [ - ] rsync [ ? ] rsyslog [ - ] saned [ ? ] screen-cleanup [ ? ] sendsigs [ ? ] speech-dispatcher [ ? ] stop-bootlogd [ ? ] stop-bootlogd-single [ ? ] udev [ ? ] udev-finish [ ? ] udevmonitor [ ? ] udevtrigger [ ? ] ufw [ ? ] umountfs [ ? ] umountnfs.sh [ ? ] umountroot [ ? ] unattended-upgrades [ - ] urandom [ + ] winbind [ ? ] wpa-ifupdown [ - ] x11-common

  Read the article

• Random Slow Response

  - by ARehman

  We have an ASP.NET MVC 1.0 application running on Windows Server 2008 – Standard (32 –bit), Dual Core Xeon (3.0 GHz), 2 G.B R.A.M. Most of the times application renders response in 3-4 seconds, but sometimes users get very late response and delay is up to 40 seconds or more than a minute. It happens in following way: User browsed a page, idle for 5, 10 or 15 minutes, tried to browse same page or some other. Now, there is a chance that he will see late response whereas the app pool is still up and running. This can happen with any arbitrary page. We have tried followings/observations. Moved the application to stand alone web server App Pool idle shutdown time is 60 minutes. There are no abrupt shut downs/restarts. CPU or memory doesn’t spike. No delays in SQL queries. Modified App Pool setting to run in classic-mode. It didn’t help. Plugged-in custom module to log all those requests which took more than 5 seconds to complete. It didn’t pick any request of interest. Enabled ‘Failed Request Tracing’ to log all those requests which take 20 or more seconds to complete. It didn’t log anything. Event Viewer, HTTPER log, W3SVC logs or WAS logs don’t indicate anything. HTTPERR only has ‘_ _ Timer_ConnectionIdle _ _’ entries. There is not much traffic to server. This can happen also if only two users are active. Next we captured TCP/IP terrific on both a user and server end with Wireshark and below are details in brief of this slowness: Browser sends a request for ~/User/Home/ (GET Request) by setting up a receiving end point using port 'wlbs(port-2504)'. I'm not sure if this could be a problem in some way that browser didn't hand-shake with the server first and assumed that last connection is still open, whereas, I browsed the same page 4 minutes ago and didn't perform any activity with site after that. If I see the HTTPERR log, it indicates that it has ‘_ _ Timer_ConnectionIdle _ _ _’ entry for my last activity with server. Browser (I was using Chrome) waits for any response from the server, doesn’t find any then starts retransmitting the same request using same end point after incrementing wait intervals, e.g. after 8, 18, 29, 40, 62, and 92 seconds. All these GET requests were received by server as well. But, server didn’t send any packet to client. Browser didn't see any response on the end point it set up in point 1, it opened a new end point 'optiwave-lm (port-2524)', did a hand shake with the server and transmitted the same request again. Server received, processed it, and returned successful response. What happened to earlier 6-7 requests? Whether they were passed on to HTTP.SYS or not? Why Failed Request Tracing not logged anything, we didn't find any clue yet. Server served the same page successfully just 4 minutes ago. Looking forward for more suggestions/solutions. -- Thanks

  Read the article

• TV not detected by Windows/VGA - when there is a WHDI device in the signal chain

  - by ashwalk

  I'm at my wit's end with this one... I had an EVGA GTS 250, and I used to plug it's HDMI out into a WHDI sender, which transmitted to its corresponding WHDI receiver 15ft away, which then connected to a Samsung LN40D LCD TV through another HDMI cable. PC/VGA < [hdmi cable] < WHDI sender <[air] WHDI receiver < [hdmi cable] < TV It was perfect, stable, no perceivable latency. I just plugged everything the first time and it worked instantly. It sent 5.1 audio, and Windows/nVidia Control Center detected the TV by its name. The WHDI device is this one: http://goo.gl/Q8iWI5 Now I bought an EVGA GTX 650, and WHDI doesn't work anymore. Both Windows and nVidia Control Center won't detect the TV, only the monitor that's connected via DVI. The TV screen shows "TX202913 connected. Check video signal." on top of a black screen. Though the device is not the problem itself, just the fact that it's not allowing direct connection between PC and TV. I would bet that if put an AVR in its place I'd also have this issue. The HDMI on this new card works with other monitors. If I put the older card back, WHDI works normally. I have googled this for 5 months on and off. Once I bumped into a page that showed how to force a display device to always-on through registry edit. Once I restarted windows, the Tv (through WHDI) displayed my expanded or duplicated desktop at 1024x768 ONLY, and listed the display as "digital display". I could not change the resolution and it wouldn't playback audio (although the option was available at nVidia Control Center HDMI audio options, but did not work). This proves that there is no conflict between the devices, except that software-wise, Windows cannot, for the life of it, understand that there's a TV there to send video/audio to. Since this won't do (no audio, poor video), I reverted this regedit. It's also not an EDID problem within the TV, since when connected directly it works. The last weird bit of this saga is that today, I reminded of Windows' "Add Device" dialog, gave it a go, and a "Samsung Generic UPNP TV" showed up, which I promptly installed the drives for, rising to a climax of... ...NOTHING HAPPENING. As far as I can tell, it really didn't change anything other than using up a few kb in my main disc. I should also say that I looked a LOT into handshake problems and nothing applied either. Do any of you have an idea of what may be going on? I can't stand the thought of having a us$200 device not working because of the addition of a newer graphics card, when the much older one had no issues. There is absolutely NO REASON for this to happen. There is NO documentation on WHDI online. Apparently no one buys this stuff. For the same reason, no one responded to this same plea for help on NVidia and EVGA forums. Worst case, this can be a warning about this setup for people in the future. Thanx in advance.

  Read the article

• Yet again: "This device can perform faster" (Samsung Galaxy Tab 2)

  - by Mike C

  I've been doing a lot of research with no reasonable solution. Please excuse the length of my post. When I plug my Galaxy Tab 2 (7" / Wi-Fi only / Android ICS) into my Windows 7 64-bit machine, I (almost always) get this warning popup that "This device can perform faster." And in fact, transfers onto the Tab in this mode are slow. The two times I've been able to get a high-speed connection, the transfer has occurred at the expected speed. I just don't know what to do to get that high-speed transfer. (The first time I did, it was the first time I connected the Tab; the second time I did, I was fiddling around and unplugging/plugging in again.) That popup is telling me that the device is USB2, but that it thinks I've connected to a USB1 port. In fact, every USB port (there are ten) on this system is USB2. It's an ASUS M3A78-EMH mobo from late 2008. I'm not sure what the chipset is; the CPU is an AMD Athlon 4850e, but I've seen this message reported for non-AMD systems. (Every mobo reference I've seen in reports on this has been for Asus, but of course most reporters aren't reporting that info at all.) The Windows 7 installation is just a couple weeks old (I had a disk crash) but I saw the same warning on the WinXP/64 that was installed previously. In Device Manager, there are two "Standard Enhanced PCI to USB Host Controller" nodes which are the actual high-speed controllers. There are also five "Standard OpenHCD USB Host Controller" nodes, which I have determined are virtual USB1 controllers embedded in the "Enhanced" controllers. (In Device Manager, I'm using View|Devices by Connection.) My high-speed thumb drives, external disks, and iPod all show up as subnodes of the "Enhanced" controllers; the keyboard, mouse, and USB speakers under the "OpenHCD" ones -- and this is true no matter which ports these devices are plugged into. The Tab shows up under an OpenHCD node, unsurprisingly. It appears as a threesome: a top-level "Mobile USB Composite device" with two subs: "Galaxy Tab 2" and "Mobile USB Modem." (I have no idea what the modem device implies or how I might use it, but I don't care about it either: I just want the Tab to reliably connect at high speed.) On the Tab, the USB support has a switch between PTP and MTP, the latter being the default, and the preferred mode for me (as I'm usually hooking it up for music synch). I have tried, however, connecting it as PTP, and it still connects as USB 1. (As PTP, only the "Galaxy Tab 2" device appears -- no Composite, no Modem.) If it's plugged in as MTP and I change the setting to PTP, Windows unloads and reloads the device, and voila: The Tab appears under an "Enhanced" node, but eventually re-loads again to show a exclamation icon on the device; Properties then shows "This device cannot start." Same response if I plug it in as PTP and then change to MTP; in this case, only the Tab itself shows the exclamation, not the other two devices. One thing I have not tried, and really would prefer to avoid, is installing the "beta" chipset driver available on the Asus website, which is dated 2009. Windows tells me it has the most up-to-date drivers for the Tab, and for the chipset, and I'm inclined to believe that. I suspect the problem is with the Samsung drivers, or possibly the hardware. One suggestion I saw elsewhere which might, possibly, pertain is to ensure the USB cable is properly shielded; however, the Tab has one of those misbegotten 30-pin, not-quite-an-iPod connectors; I don't know if I could find a 3rd party one. It seems unlikely that this cable is improperly shielded, tho. (Is there a way to test that?) So, my question is: does anyone know how to get this working as one might reasonably expect it to?

  Read the article

• unable to sniff traffic despite network interface being in monitor or promiscuous mode

  - by user65126

  I'm trying to sniff out my network's wireless traffic but am having issues. I'm able to put the card in monitor mode, but am unable to see any traffic except broadcasts, multicasts and probe/beacon frames. I have two network interfaces on this laptop. One is connected normally to 'linksys' and the other is in monitor mode. The interface in monitor mode is on the right channel. I'm not associated with the access point because, as I understand, I don't need to if using monitor mode (vs promiscuous). When I try to ping the router ip, I'm not seeing that traffic show up in wireshark. Here's my ifconfig settings: daniel@seasonBlack:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:29:9e:b2:89 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8518 (8.5 KB) TX bytes:8518 (8.5 KB) wlan0 Link encap:Ethernet HWaddr 00:21:00:34:f7:f4 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:ff:fe34:f7f4/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:9758 errors:0 dropped:0 overruns:0 frame:0 TX packets:4869 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3291516 (3.2 MB) TX bytes:677386 (677.3 KB) wlan1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-33-34-00-00-00-00-00-00-00-00 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:1500 Metric:1 RX packets:112754 errors:0 dropped:0 overruns:0 frame:0 TX packets:101 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18569124 (18.5 MB) TX bytes:12874 (12.8 KB) wmaster0 Link encap:UNSPEC HWaddr 00-21-00-34-F7-F4-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Here's my iwconfig settings: daniel@seasonBlack:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:F8:D6:17:34 Bit Rate=54 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=68/70 Signal level=-42 dBm Noise level=-69 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wmaster1 no wireless extensions. wlan1 IEEE 802.11bg Mode:Monitor Frequency:2.437 GHz Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Here's how I know I'm on the right channel: daniel@seasonBlack:~$ iwlist channel lo no frequency information. eth0 no frequency information. wmaster0 no frequency information. wlan0 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6) wmaster1 no frequency information. wlan1 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6)

  Read the article

• 2 drives, slow software RAID1 (md)

  - by bart613

  Hello, I've got a server from hetzner.de (EQ4) with 2* SAMSUNG HD753LJ drives (750G 32MB cache). OS is CentOS 5 (x86_64). Drives are combined together into two RAID1 partitions: /dev/md0 which is 512MB big and has only /boot partitions /dev/md1 which is over 700GB big and is one big LVM which hosts other partitions Now, I've been running some benchmarks and it seems like even though exactly the same drives, speed differs a bit on each of them. # hdparm -tT /dev/sda /dev/sda: Timing cached reads: 25612 MB in 1.99 seconds = 12860.70 MB/sec Timing buffered disk reads: 352 MB in 3.01 seconds = 116.80 MB/sec # hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 25524 MB in 1.99 seconds = 12815.99 MB/sec Timing buffered disk reads: 342 MB in 3.01 seconds = 113.64 MB/sec Also, when I run eg. pgbench which is stressing IO quite heavily, I can see following from iostat output: Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.00 231.40 0.00 298.00 0.00 9683.20 32.49 0.17 0.58 0.34 10.24 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 231.40 0.00 298.00 0.00 9683.20 32.49 0.17 0.58 0.34 10.24 sdb 0.00 231.40 0.00 301.80 0.00 9740.80 32.28 14.19 51.17 3.10 93.68 sdb1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sdb2 0.00 231.40 0.00 301.80 0.00 9740.80 32.28 14.19 51.17 3.10 93.68 md1 0.00 0.00 0.00 529.60 0.00 9692.80 18.30 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.00 0.60 0.00 4.80 8.00 0.00 0.00 0.00 0.00 dm-1 0.00 0.00 0.00 529.00 0.00 9688.00 18.31 24.51 49.91 1.81 95.92 Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.00 152.40 0.00 330.60 0.00 5176.00 15.66 0.19 0.57 0.19 6.24 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 152.40 0.00 330.60 0.00 5176.00 15.66 0.19 0.57 0.19 6.24 sdb 0.00 152.40 0.00 326.20 0.00 5118.40 15.69 19.96 55.36 3.01 98.16 sdb1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sdb2 0.00 152.40 0.00 326.20 0.00 5118.40 15.69 19.96 55.36 3.01 98.16 md1 0.00 0.00 0.00 482.80 0.00 5166.40 10.70 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-1 0.00 0.00 0.00 482.80 0.00 5166.40 10.70 30.19 56.92 2.05 99.04 Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.00 181.64 0.00 324.55 0.00 5445.11 16.78 0.15 0.45 0.21 6.87 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 181.64 0.00 324.55 0.00 5445.11 16.78 0.15 0.45 0.21 6.87 sdb 0.00 181.84 0.00 328.54 0.00 5493.01 16.72 18.34 61.57 3.01 99.00 sdb1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sdb2 0.00 181.84 0.00 328.54 0.00 5493.01 16.72 18.34 61.57 3.01 99.00 md1 0.00 0.00 0.00 506.39 0.00 5477.05 10.82 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-1 0.00 0.00 0.00 506.39 0.00 5477.05 10.82 28.77 62.15 1.96 99.00 And this is completely getting me confused. How come two exactly the same specced drives have such a difference in write speed (see util%)? I haven't really paid attention to those speeds before, so perhaps that something normal -- if someone could confirm I would be really grateful. Otherwise, if someone have seen such behavior again or knows what is causing such behavior I would really appreciate answer. I'll also add that both "smartctl -a" and "hdparm -I" output are exactly the same and are not indicating any hardware problems. The slower drive was changed already two times (to new ones). Also I asked to change the drives with places, and then sda were slower and sdb quicker (so the slow one was the same drive). SATA cables were changed two times already.

  Read the article

< Previous Page | 742 743 744 745 746 747 748 749 750 751 752 753  | Next Page >