Search Results

Search found 25123 results on 1005 pages for 'domain model'.

Page 834/1005 | < Previous Page | 830 831 832 833 834 835 836 837 838 839 840 841  | Next Page >

• iwlwifi on lenovo z570 disabled by hardware switch

  - by Kevin Gallagher

  It was working fine with windows 7. The hardware switch is not disabled. I've toggled it back and forth dozens of times. The wifi light never turns on and it always lists as hardware disabled. I have the latest updates installed. I've been searching for solutions, but none of them seem to work for me. I've tried removing acer-wmi. I've tried setting 11n_disable=1. I've tried resetting the bios. I've tried using rfkill to unblock (only removes soft block). I've rebooted dozens of times. The wifi light turns off as soon as grub loads. Edit: I have a usb edimax wireless nic. It shows hardware disabled as well (although rfkill lists as unblocked). If I unload iwlwifi the usb nic works fine. uname -a `Linux xxx-Ideapad-Z570 3.2.0-55-generic #85-Ubuntu SMP Wed Oct 2 12:29:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linu`x rfkill list 19: phy18: Wireless LAN Soft blocked: no Hard blocked: yes dmesg [43463.022996] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [43463.023002] Copyright(c) 2003-2011 Intel Corporation [43463.023107] iwlwifi 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [43463.023190] iwlwifi 0000:03:00.0: setting latency timer to 64 [43463.023253] iwlwifi 0000:03:00.0: pci_resource_len = 0x00002000 [43463.023257] iwlwifi 0000:03:00.0: pci_resource_base = ffffc900057c8000 [43463.023261] iwlwifi 0000:03:00.0: HW Revision ID = 0x0 [43463.023797] iwlwifi 0000:03:00.0: irq 43 for MSI/MSI-X [43463.024013] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [43463.024250] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S [43463.045496] iwlwifi 0000:03:00.0: device EEPROM VER=0x15d, CALIB=0x6 [43463.045501] iwlwifi 0000:03:00.0: Device SKU: 0X50 [43463.045504] iwlwifi 0000:03:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [43463.045542] iwlwifi 0000:03:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [43463.045744] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio. [43463.047652] iwlwifi 0000:03:00.0: loaded firmware version 39.31.5.1 build 35138 [43463.047823] Registered led device: phy18-led [43463.047895] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [43463.048037] ieee80211 phy18: Selected rate control algorithm 'iwl-agn-rs' [43463.055533] ADDRCONF(NETDEV_UP): wlan0: link is not ready nm-tool State: connected (global) - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: unavailable Default: no HW Address: 74:E5:0B:4A:9F:C2 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points lshw -C network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:4a:9f:c2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-55-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:43 memory:f1500000-f1501fff lspci 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]

  Read the article

• Webcast

  - by bwalstra

  v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif";} Invites You To: Monetizing Digital Media From Clicks To Cash Digital goods and services are booming, and smart businesses are transforming the way they sell and deliver their offerings in the exploding digital marketplace. Using information-services, credit-card, and digital-media examples Oracle’s Mustafa Oyumi and Tripp Partain will show the Oracle Digital Media solution - from clicks to cash: · Design, Model, and Launch New Products · Review Real Time Market Effectiveness and Respond · Rate, Bill, Invoice, Revenue Rec, and Collect · Determine Rights, Royalties, Licensing, and Commissions · Analyze Enterprise Results Friday, July 6, 2012 11:00 a.m. – 11:45 a.m. <Webcast Details> <Webcast Details> Agenda 11:00 a.m. Overview 11:10 a.m. Demo 11:30 a.m. Q&A Copyright © 2012, Oracle. All rights reserved. Contact Us | Legal Notices and Terms of Use | Privacy Statement 36526 Oracle Corporation - Worldwide Headquarters, 500 Oracle Parkway, OPL - E-mail Services, Redwood Shores, CA 94065, United States Create or update your profile to receive customized e-mail about Oracle products and services. If you do not wish to receive any further electronic marketing communications from Oracle you can Opt-Out completely, please note you will no longer receive newsletters and product information you may have subscribed to.

  Read the article

• No suspend on lid closing on a Samsung Series 5 14" NP530U4BI

  - by dmeu

  Ok, i realize I am not the only one, but I will try to provide all info possible to make it exemplary as possible and narrow down the error sources. I have a fresh install of Ubuntu 12.04 and the suspend worked fine upon having it freshly installed but now it does not anymore. The suspend option from the system power button on the top right works fine. Things I did do which I don't know if they are related: Install and remove againthe FGLRX drivers (Radeon graphic card) Install Jupiter power managment (shutting it down is not changin anything) Plug in and out an external display The configuration I know of is well set: In System Settings/Power all is set to suspend when closing lid Double checked with dconf-editor, everything set to suspend So, from here on I don't know how to proceed.. what are common problems that cause this error? EDIT: My computer model is: Samsung Series 5 14" NP530U4BI $ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 04) 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Thames [Radeon 7500M/7600M Series] 02:00.0 Network controller [0280]: Intel Corporation Centrino Advanced-N 6230 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller 04:00.0 USB controller [0c03]: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller

  Read the article

• Accessing SQL Server data from iOS apps

  - by RobertChipperfield

  Almost all mobile apps need access to external data to be valuable. With a huge amount of existing business data residing in Microsoft SQL Server databases, and an ever-increasing drive to make more and more available to mobile users, how do you marry the rather separate worlds of Microsoft's SQL Server and Apple's iOS devices? The classic answer: write a web service layer Look at any of the questions on this topic asked in Internet discussion forums, and you'll inevitably see the answer, "just write a web service and use that!". But what does this process gain? For a well-designed database with a solid security model, and business logic in the database, writing a custom web service on top of this just to access some of the data from a different platform seems inefficient and unnecessary. Desktop applications interact with the SQL Server directly - why should mobile apps be any different? The better answer: the iSql SDK Working along the lines of "if you do something more than once, make it shared," we set about coming up with a better solution for the general case. And so the iSql SDK was born: sitting between SQL Server and your iOS apps, it provides the simple API you're used to if you've been developing desktop apps using the Microsoft SQL Native Client. It turns out a web service remained a sensible idea: HTTP is much more suited to the Big Bad Internet than SQL Server's native TDS protocol, removing the need for complex configuration, firewall configuration, and the like. However, rather than writing a web service for every app that needs data access, we made the web service generic, serving only as a proxy between the SQL Server and a client library integrated into the iPhone or iPad app. This client library handles all the network communication, and provides a clean API. OSQL in 25 lines of code As an example of how to use the API, I put together a very simple app that allowed the user to enter one or more SQL statements, and displayed the results in a rather primitively formatted text field. The total amount of Objective-C code responsible for doing the work? About 25 lines. You can see this in action in the demo video. Beta out now - your chance to give us your suggestions! We've released the iSql SDK as a beta on the MobileFoo website: you're welcome to download a copy, have a play in your own apps, and let us know what we've missed using the Feedback button on the site. Software development should be fun and rewarding: no-one wants to spend their time writing boiler-plate code over and over again, so stop writing the same web service code, and start doing exciting things in the new world of mobile data!

  Read the article

• Advice for how to handle company pride

  - by user17971

  We have this "amazing" little product using the latest development methodologies, components with all the bells and whistles. I took over this product maybe 6 months ago and struggled with it from day one. Even though it is supposedly is state of the art because of all its amazing structure, using dependency injections, inversion of control from the unity framework, hibernation and is domain driven in a .net mvvm xaml application to make it streamlined and modular. I knew from the moment I saw the monolith that it was going to be an uphill struggle for me. A lot of little code-bits scattered all around in neatly organized paradigms. Debugging is difficult, tracing the code is difficult, making new code is difficult, although some modifications is surprisinly easy but it doesn't out weight the problems I have with the code by a long shot. When I took over the project I was told that the new management console was ready for delivery and all I had to do was compile it and drop it. This was the beginning of a uphill struggle, our customer didn't agree at all that this was the functionality they had asked for so I had to do modifications to the program to their specifications. Since the project pretty much has been overdue since I took over it it has always been important that we didn't add or change much to the original system. I could modify the existing bits. fast forward until today where I finally completed all their comments and issues with the program but now I think that the users has opened their eyes (even though they saw this program many times) that they will be going backwards with this new system, that it will be much worse than the tool they got today (for a long time due to the fact that I'm the only resource on the project, project manager, tester, developer, integration specialist etc) My problem is that I lost faith in this system quite early due to the nature of the program. Although I made many changes and improvements to the system I wholeheartedly sympathize with the poor users who are going to start using this system. Its not nearly doing all the things it should do. I had this conversation internally with my boss where I told him what I thought about it, that if I were the customer I wouldn't have spent money developing it. So what do I do now? The system in ready, on a staging system and nobody likes it, its too slow and boring and does maybe do 50% of what they need it to do. Despite how much energy and working around the clock I've done to this project: I won't mind scrapping the system but we've spent much money (well my salaries) developing it and my company wants us to be proud of everything we do and advocate it. How will I tackle the contractor when he asks for advice? Surely I can tell him, this is what we agreed upon based on your use case scenarios, and be done with it? How will I inform my boss about this progress? He knows what I feel about it but I always get the feeling he let my criticism pass him by as just hot air, gone tomorrow,.

  Read the article

• It is CX a new concept?

  - by Isabel F. Peñuelas

  The Marketing Industry and the Web Industry are talking about CX since some time. However it is only very recently that the concept has reached some common meaning accepted by the analysts’ and the IT community. The new CX model depends on two previous facts: the expansion of the social media, and the impact of the new advanced features of mobile devices regarding brand-customer interaction. CXsers vs UXers First there is some need of disambiguity between User Experience and Customer Experience. User Experience -UX, is a much well established concept related with the design of user interactions for particular devices. UX people are interested on multiple touch points of digital interfaces while CX people are interested on all kind of interfaces including physical ones. UX is an evolution of Web Usability, while CX is a marketing concept. UX is an instrument of User Experience. CX in fact is all about Connections and Interactions. Connections Dan Draper, the creative director Mad Men, understands very well that to market effectively means to connect with people, and the best way to connect to people is to use the connections people have with other people: understanding Social Media connections and taking the customer pulse of customers on those medias, and are strong facilitators of CX strategies.  Interactions We can very simply define CX as the relationship that a customer establishes with a brand through multiple touch points (interactions, channels) through the entire life cycle of his relationship- direct or indirect with the brand. Interactions can be grouped on Customer Journeys through multiple touch points defined as the path a customer follows to achieve a goal. Processes A customer journey today usually starts at the moment he surfs the Web, then he takes a purchase decision; purchases the product;  request a particular service and finally recommends or do not recommends the product.  Customer Journeys are processes, and to analyze customer journeys there exists today a broad offering of modern Customer Journey tools very similar actually to the use cases or UML activity diagrams for IT systems design. As a summary CX is nothing more and nothing less than applying process analysis methods for better understanding how to create value through customer interactions across the multiple user´s touch points with the brand.

  Read the article

• Updating an Entity through a Service

  - by GeorgeK

  I'm separating my software into three main layers (maybe tiers would be a better term): Presentation ('Views') Business logic ('Services' and 'Repositories') Data access ('Entities' (e.g. ActiveRecords)) What do I have now? In Presentation, I use read-only access to Entities, returned from Repositories or Services, to display data. $banks = $banksRegistryService->getBanksRepository()->getBanksByCity( $city ); $banksViewModel = new PaginatedList( $banks ); // some way to display banks; // example, not real code I find this approach quite efficient in terms of performance and code maintanability and still safe as long as all write operations (create, update, delete) are preformed through a Service: namespace Service\BankRegistry; use Service\AbstractDatabaseService; use Service\IBankRegistryService; use Model\BankRegistry\Bank; class Service extends AbstractDatabaseService implements IBankRegistryService { /** * Registers a new Bank * * @param string $name Bank's name * @param string $bik Bank's Identification Code * @param string $correspondent_account Bank's correspondent account * * @return Bank */ public function registerBank( $name, $bik, $correspondent_account ) { $bank = new Bank(); $bank -> setName( $name ) -> setBik( $bik ) -> setCorrespondentAccount( $correspondent_account ); if( null === $this->getBanksRepository()->getDefaultBank() ) $this->setDefaultBank( $bank ); $this->getEntityManager()->persist( $bank ); return $bank; } /** * Makes the $bank system's default bank * * @param Bank $bank * @return IBankRegistryService */ public function setDefaultBank( Bank $bank ) { $default_bank = $this->getBanksRepository()->getDefaultBank(); if( null !== $default_bank ) $default_bank->setDefault( false ); $bank->setDefault( true ); return $this; } } Where am I stuck? I'm struggling about how to update certain fields in Bank Entity. Bad solution #1: Making a series of setters in Service for each setter in Bank; - seems to be quite reduntant, increases Service interface complexity and proportionally decreases it's simplicity - something to avoid if you care about code maitainability. I try to follow KISS and DRY principles. Bad solution #2: Modifying Bank directly through it's native setters; - really bad. If you'll ever need to move modification into the Service, it will be pain. Business logic should remain in Business logic layer. Plus, there are plans on logging all of the actions and maybe even involve user permissions (perhaps, through decorators) in future, so all modifications should be made only through the Service. Possible good solution: Creating an updateBank( Bank $bank, $array_of_fields_to_update) method; - makes the interface as simple as possible, but there is a problem: one should not try to manually set isDefault flag on a Bank, this operation should be performed through setDefaultBank method. It gets even worse when you have relations that you don't want to be directly modified. Of course, you can just limit the fields that can be modified by this method, but how do you tell method's user what they can and cannot modify? Exceptions?

  Read the article

• TechEd 2012: Windows 8 And Metro

  - by Tim Murphy

  Windows 8 is here (or at least very close) and that was the main feature of this morning’s key note.  Antoine LeBlond started off by apologizing to the IT professionals since he planned on showing code.  I’m not sure if IT Pros are that easily confused or why you would need such a disclaimer.  Developers do real work, IT Pros just play with toys (just kidding). The highlights of the Windows 8 keynote for me started with some of the UI design elements that I had not seen when I was shown one of the Build tablets.  Specifically I liked the AppBar features that we have become used to with Windows Phone and some of the gesture features.  Even though they have been available on other platforms before I think Microsoft really got them right. Two other great features of Windows 8 that they demonstrated were the Hyper-V capabilities and the ability to run Windows 8 anywhere from a USB key.  My jaw dropped through the floor seeing a feature rich OS boot off of a thumb drive. WOW!  I also can’t wait to get rid of dual booting just to run Hyper-V images when developing. The morning continued with a session on Metro XAML development with Tim Heuer.  While included a lot of great XAML Metro demos, I was pleasantly surprised by some of the things I found out about Visual Studio 2012.  Finding out that Blend is now integrated with VS2012 was a nice addition after working with them as separate applications was an encouraging start. Moving on to Metro he introduced the nugget that WinRT is Async everywhere.  How deep this model goes will be an interesting thing to find out as I learn more about developing for the platform.  Thankfully he followed that up with a couple of new keywords, await and async, that eliminates a lot of plumbing that has been required in the past for asynchronous transactions. Tim also related that since the Metro framework is relatively small and most apps will use a significant amount of it the entire surface is referenced by default.  This is a contrast to adding namespace and assemblies one after another as we normally do. This was such a power packed session that I can’t detail it all here so here is the teaser list. New icons in VS2012 for extension methods Emulator/simulator testing features for gestures Portable class libraries XAML no longer managed code And so much more …   del.icio.us Tags: Windows 8,Metro,Tim Heuer,XAML,Widows Phone,Hyper-V,Antoine LeBlond,TechEd,TechEd 2012,Visual Studio 2012,Visual Studio

  Read the article

• Bridging 10GbE with 12.04 - bridging works but the bridging computer has no internet access

  - by Donal

  I have been trying to get 12.04 bridging working with two 10GbE cards. I have 2 10GbE cards in a linux box being used only for this bridge, 1 with 2 10GbaseT ports and another with a single CX4 port. I have 2 client computers connected with 10GbaseT cards and the CX4 card connects to a procurve switch. I can get the bridging happening mostly the way that I want, The clients receive dhcp information from the dhcp server (not the bridging machine) and can connect to and properly see the rest of the network. Speeds are ok, not amazing but working on that is another matter. My problem is that the bridging machine has no internet access ... meaning I can't update anything or apt-get anything It can ping all other machines on the local network. I've tried the helpful hints from: https://help.ubuntu.com/community/NetworkConnectionBridge "Enabling Internet Use on the Bridging Computer" and get the following RTNETLINK answers: File exists but dhclient br0 does nothing for me :( I think if it is anything it a multiple route problem as both br0 and eth4 have ipaddresses ... even though I have only set it up so that br0 has one ... Bridge setup details: /etc/network/interface auto br0 iface br0 inet static address 192.168.0.246 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 dns-nameservers 192.168.0.1 dns-search example.com dns-domain example.com #(eth2 & eth3 are the 10GbaseT) #(eth4 is the CX4 connection) pre-up ip link set eth2 down pre-up ip link set eth3 down pre-up ip link set eth4 down pre-up brctl addbr br0 pre-up brctl addif br0 eth4 eth3 eth2 pre-up ip addr flush dev eth3 pre-up ip addr flush dev eth2 pre-up ip addr flush dev eth4 post-down ip link set eth4 down post-down ip link set eth2 down post-down ip link set eth3 down post-down ip link set br0 down post-down brctl delif br0 eth2 eth3 eth4 post-down brctl delbr br0 ifconfig -a br0 Link encap:Ethernet HWaddr 00:15:17:22:20:34 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:17ff:fe22:2034/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4957 errors:0 dropped:0 overruns:0 frame:0 TX packets:1077 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:596320 (596.3 KB) TX bytes:139952 (139.9 KB) eth4 Link encap:Ethernet HWaddr 00:60:dd:47:7c:05 inet addr:192.168.0.57 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:7c05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:15391 errors:0 dropped:51 overruns:0 frame:0 TX packets:1207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5916769 (5.9 MB) TX bytes:154312 (154.3 KB) Interrupt:70 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth4 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth4

  Read the article

• Sharing on Github

  - by Alan

  Over the past couple weeks I have gotten a lot of help from StackOverflow users on a project, and rather than keep the finished product to myself I wanted to share it unencumbered by licenses, but don't want there to be so much legwork during installation that users shy away from trying it. I am about to post it to Github and choosing public domain licensing. I would like to to be super simple for users to make use of and just FTP it up and go. That being said, do I need to make sure I remove things like the JQuery file, and other GPL / MIT licensed dependencies that I didn't write but that my code depends on? I haven't removed any copyright notices from the other code and all of it open source, it would just be nice if users could download everything at once while of course not trying to represent that I am the license holder of the dependencies. Inside my files are also some snippets, do those have to be externalized with installation instructions or can it be posted as is? Here is an example, my nav.php file is 115 lines long and I have these at the top: <script type="text/javascript" src="./js/ddaccordion.js"> /*********************************************** * Accordion Content script- (c) Dynamic Drive DHTML code library (www.dynamicdrive.com) * Visit http://www.dynamicDrive.com for hundreds of DHTML scripts * This notice must stay intact for legal use ***********************************************/ </script> <link href="css/admin.css" rel="stylesheet"> <script type="text/javascript"> ddaccordion.init({ headerclass: "submenuheader", //Shared CSS class name of headers group contentclass: "submenu", //Shared CSS class name of contents group revealtype: "click", //Reveal content when user clicks or onmouseover the header? Valid value: "click", "clickgo", or "mouseover" mouseoverdelay: 200, //if revealtype="mouseover", set delay in milliseconds before header expands onMouseover collapseprev: false, //Collapse previous content (so only one open at any time)? true/false defaultexpanded: [], //index of content(s) open by default [index1, index2, etc] [] denotes no content onemustopen: false, //Specify whether at least one header should be open always (so never all headers closed) animatedefault: false, //Should contents open by default be animated into view? persiststate: true, //persist state of opened contents within browser session? toggleclass: ["", ""], //Two CSS classes to be applied to the header when it's collapsed and expanded, respectively ["class1", "class2"] togglehtml: ["suffix", "<img src='./images/plus.gif' class='statusicon' />", "<img src='./images/minus.gif' class='statusicon' />"], //Additional HTML added to the header when it's collapsed and expanded, respectively ["position", "html1", "html2"] (see docs) animatespeed: "fast", //speed of animation: integer in milliseconds (ie: 200), or keywords "fast", "normal", or "slow" oninit:function(headers, expandedindices){ //custom code to run when headers have initalized //do nothing }, onopenclose:function(header, index, state, isuseractivated){ //custom code to run whenever a header is opened or closed //do nothing } }) </script>

  Read the article

• Using HBase or Cassandra for a token server

  - by crippy

  I've been trying to figure out how to use HBase/Cassandra for a token system we're re-implementing. I can probably squeeze quite a lot more from MySQL, but it just seems it has come to clinging on to the wrong tool for the task just because we know it well. Eventually will hit a wall (like happened to us in other areas). Naturally I started looking into possible NoSQL solutions. The prominent ones (at least in terms of buzz) are HBase and Cassandra. The story is more or less like this: A user can send a gift other users. Each gift has a list of recipients or is public in which case limited by number or expiration date For each gift sent we generate some token that uniquely identifies that gift. For each gift we track the list of potential recipients and their current status relating to that gift (accepted, declinded etc). A user can request to see all his currently pending gifts A can request a list of users he has sent a gift to today (used to limit number of gifts sent) Required the ability to "dump" or "ignore" expired gifts (x day old gifts are considered expired) There are some other requirements but I believe the above covers the essentials. How would I go and model that using HBase or Cassandra? Well, the wall was performance. A few 10s of millions of records per day over 2 tables kept for 2 weeks (wish I could have kept it for more but there was no way). The response times kept getting slower and slower until eventually we had to start cutting down number of days we kept data. Caching helps here but it's not an ideal solution since a big part of the ops are updates. Also, as I hinted in my original post. We use MySQL extensively. We know exactly what it can and can't do both in naive implementations followed by native partitioning and finally by horizontally sharding our dataset on the application level to reside on multiple DB nodes. It can be done, but that's not really what I'm trying to get from this. I asked a very specific question about designing a solution using a NoSQL solution since it's very hard to find examples for designs out there. Brainlag, not trying to come off as rude. I actually appreciate it a lot that you are the only one who even bothered to respond. but I see it over and over again. People ask questions and others assume they have no idea what they're talking about and give an irrelevant answer. Ignore RDBMS please. The question is about nosql.

  Read the article

• nvidia optimus laptops

  - by kellogs

  kellogs@kellogs-K52Jc ~ $ lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 80) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 80) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 80) 03:00.4 System peripheral: JMicron Technology Corp. xD Host Controller (rev 80) 03:00.5 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 03) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) kellogs@kellogs-K52Jc ~ $ inxi -SGx System: Host: kellogs-K52Jc Kernel: 3.5.0-17-generic x86_64 (64 bit, gcc: 4.7.2) Desktop: KDE 4.9.5 (Qt 4.8.3) Distro: Linux Mint 14 Nadia Graphics: Card: Intel Core Processor Integrated Graphics Controller bus-ID: 00:02.0 X.Org: 1.13.0 drivers: intel (unloaded: fbdev,vesa) Resolution: [email protected] GLX Renderer: Mesa DRI Intel Ironlake Mobile GLX Version: 2.1 Mesa 9.0.3 Direct Rendering: Yes Manufacturer advertises the K52Jc model which I bought as optimus enabled. However, no traces of it in the output above. Of course, Bumblebee would not start on this machine. Should I rest assured that is a defective / un-optimused machine ? thanks

  Read the article

• JDK bug migration milestone: JIRA now the system of record

  - by darcy

  I'm pleased to announce the OpenJDK bug database migration project has reached a significant milestone: the JDK has switched from the legacy Sun "bugtraq" system to a new internal JIRA instance as the system of record for our bug tracking. This completes the initial phase of the previously described plan of getting OpenJDK onto an externally visible and writable bug tracker. The identities contained in the current system include recognized OpenJDK contributors. The bug migration effort to date has been sizable in multiple dimensions. There are around 140,000 distinct issues imported into the JDK project of the JIRA instance, nearly 165,000 if backport issues to track multiple-release information are included. Separately, the Code Tools OpenJDK project has its own JIRA project populated with several thousands existing bugs. Once the OpenJDK JIRA instance is externalized, approved OpenJDK projects will be able to request the creation of a JIRA project for issue tracking. There are many differences in the schema used to model bugs between the legacy bug system and the schema for the new JIRA projects. We've favored simplifications to the existing system where possible and, after much discussion, we've settled on five main states for the OpenJDK JIRA projects: New Open In progress Resolved Closed The Open and In-progress states can have a substate Understanding field set to track whether the issues has its "Cause Known" or "Fix understood". In the closed state, a Verification field can indicate whether a fix has been verified, unverified, or if the fix has failed. At the moment, there will be very little externally visible difference between JIRA for OpenJDK and the legacy system it replaces. One difference is that bug numbers for newly filed issues in the JIRA JDK project will be 8000000 and above. If you are working with JDK Hg repositories, update any local copies of jcheck to the latest version which recognizes this expanded bug range. (The bug numbers of existing issues have been preserved on the import into JIRA). Relatively soon, we plan for the pages published on bugs.sun.com to be generated from information in JIRA rather than in the legacy system. When this occurs, there will be some differences in the page display and the terminology used will be revised to reflect JIRA usage, such as referring to the "component/subcomponent" of an issue rather than its "category". The exact timing of this transition will be announced when it is known. We don't currently have a firm timeline for externalization of the JIRA system. Updates will be provided as they become available. However, that is unlikely to happen before JavaOne next week!

  Read the article

• WebCenter Customer Spotlight: Azul Brazilian Airlines

  - by me

  Author: Peter Reiser - Social Business Evangelist, Oracle WebCenter  Solution SummaryAzul Linhas Aéreas Brasileiras (Azul Brazilian Airlines) is the third-largest airline in Brazil serving  42 destinations with a fleet of 49 aircraft and employs 4,500 crew members. The company wanted to offer an innovative site with a simple purchasing process for customers to search for and buy tickets and for the company’s marketing team to more effectively conduct its campaigns. To this end, Azul implemented Oracle WebCenter Sites, succeeding in gathering all of the site’s key information onto a single platform. Azul can now complete the Web site content updating process—which used to take approximately 48 hours—in less than five minutes. Company OverviewAzul Linhas Aéreas Brasileiras (Azul Brazilian Airlines) has established itself as the third-largest airline in Brazil, based on a business model that combines low prices with a high level of service. Azul serves 42 destinations with a fleet of 49 aircraft. It operates 350 daily flights with a team of 4,500 crew members. Last year, the company transported 15 million passengers, achieving a 10% share of the Brazilian market, according to the Agência Nacional de Aviação Civil (ANAC, or the National Civil Aviation Agency). Business ChallengesThe company wanted to offer an innovative site with a simple purchasing process for customers to search for and buy tickets and for the company’s marketing team to more effectively conduct its campaigns. Provide customers with an  innovative Web site with a simple process for purchasing flight tickets Bring dynamism to the Web site’s content updating process to provide autonomy to the airline’s strategic departments, such as marketing and product development Facilitate integration among the site’s different application providers, such as ticket availability and payment process, on which ticket sales depend Solution DeployedAzul worked with the  Oracle partner TQI to implement Oracle WebCenter Sites, succeeding in gathering all of the site’s key information onto a single platform. Previously, at least three servers and corporate information environments had directed data to the portal. The single Oracle-based platform now facilitates site updates, which are daily and constant. Business Results Gained development freedom in all processes—from implementation to content editing Gathered all of the Web site’s key information onto a single platform, facilitating its daily and constant updating, whereas the information was previously spread among at least three IT environments and had to go through a complex process to be made available online to customers Reduced time needed to update banners and other Web site content from an average of 48 hours to less than five minutes Simplified the flight ticket sales process thanks to tool flexibility that enabled the company to improve Website usability “Oracle WebCenter Sites provides an easy-to-use platform that enables our marketing department to spend less time updating content and more time on innovative activities. Previously, it would take 48 hours to update content on our Web site; now it takes less than five minutes. We have shown the market that we are innovators, enabling customer convenience through an improved flight ticket purchase process.” Kleber Linhares, Information Technology and E-Commerce Director, Azul Linhas Aéreas Brasileiras Additional Information Azul Brazilian Airlines Case Study Oracle WebCenter Sites Oracle WebCenter Sites Satellite Server

  Read the article

• What is 'Ubuntu Unity' (for the Desktop)?

  - by Martin

  Ok, so there's the buzz of Canonical (wanting to) switch for new Ubuntu version from the GNOME default desktop to their own Unity shell. (I hope that's accurate.) It seems I can not totally fathom what Unity actually is. For looking at its homepage it currently is firmly targeted at netbooks and the somehow different usage model on these. Is it a classical desktop? -- Taskbar? Shortcuts? Is the difference between Ubuntu(GNOME)+Unity more/less pronounced than the difference between Ubuntu and Kubuntu? Will "my parents" be able to get the interface if they've been using the classical gnome desktop so far? Edit: I would not like to split this up into more specific questions, as What is Unity? is exactly what the people I set up Ubuntu boxes for will ask me if they hear that the newer Ubuntu version is using that instead of the Desktop -- and it might well happen someone phrases it like that :-) I will certainly not give them the link to the HP as the explanation there does not lay out if it is a desktop or something more or something less: (It does not for me - therefore I'm asking here.) Unity is designed for netbooks and related touch-based devices. It includes [...] that makes it fast and easy to access [...] while removing screen elements that are rarely used in mobile and netbook computing. (emphasis mine) -- the explanation there doesn't even mention the desktop-PC! Unity has a vertical task management panel on the left-hand side and a menu panel at the top of the screen. [...] This sounds like a re-themed normal desktop. Clicking on an icon will give the target application focus if it is already running or launch it if it is not already running. If you click the ... Aha. Sounds like Windows 7. ... icon of an application that already has focus, Unity will activate an Expose-style view of all the open windows associated with that application. No clue what that's supposed to be. So it would really be nice if someone could explain for non desktop-design-terms experts what Unity is.

  Read the article

• determine collision angle on a rotating body

  - by jorb

  update: new diagram and updated description I have a contact listener set up to try and determine the side that a collision happened at relative to the a bodies rotation. One way to solve this is to find the value of the yellow angle between the red and blue vectors drawn above. The angle can be found by taking the arc cosine of the dot product of the two vectors (Evan pointed this out). One of my points of confusion is the difference in domain of the atan2 function html canvas coordinates and the Box2d rotation information. I know I have to account for this somehow... SS below questions: Does Box2D provide these angles more directly in the collision information? Am I even on the right track? If so, any hints? I have the following javascript so far: Ship.prototype.onCollide = function (other_ent,cx,cy) { var pos = this.body.GetPosition(); //collision position relative to body var d_cx = pos.x - cx; var d_cy = pos.y - cy; //length of initial vector var len = Math.sqrt(Math.pow(pos.x -cx,2) + Math.pow(pos.y-cy,2)); //body angle - can over rotate hence mod 2*Pi var ang = this.body.GetAngle() % (Math.PI * 2); //vector representing body's angle - same magnitude as the first var b_vx = len * Math.cos(ang); var b_vy = len * Math.sin(ang); //dot product of the two vectors var dot_prod = d_cx * b_vx + d_cy * b_vy; //new calculation of difference in angle - NOT WORKING! var d_ang = Math.acos(dot_prod); var side; if (Math.abs(d_ang) < Math.PI/2 ) side = "front"; else side = "back"; console.log("length",len); console.log("pos:",pos.x,pos.y); console.log("offs:",d_cx,d_cy); console.log("body vec",b_vx,b_vy); console.log("body angle:",ang); console.log("dot product",dot_prod); console.log("result:",d_ang); console.log("side",side); console.log("------------------------"); }

  Read the article

• What are the differences between abstract classes, interfaces, and when to use them

  - by user66662

  Recently I have started to wrap my head around OOP, and I am now to the point where the more I read about the differences between Abstract classes and Interfaces the more confused I become. So far, neither can be instantiated. Interfaces are more or less structural blueprints that determine the skeleton and abstracts are different by being able to partially develop code. I would like to learn more about these through my specific situation. Here is a link to my first question if you would like a little more background information: What is a good design model for my new class? Here are two classes I created: class Ad { $title; $description $price; function get_data($website){ } function validate_price(){ } } class calendar_event { $title; $description $start_date; function get_data($website){ //guts } function validate_dates(){ //guts } } So, as you can see these classes are almost identical. Not shown here, but there are other functions, like get_zip(), save_to_database() that are common across my classes. I have also added other classes Cars and Pets which have all the common methods and of course properties specific to those objects (mileage, weight, for example). Now I have violated the DRY principle and I am managing and changing the same code across multiple files. I intend on having more classes like boats, horses, or whatever. So is this where I would use an interface or abstract class? From what I understand about abstract classes I would use a super class as a template with all of the common elements built into the abstract class, and then add only the items specifically needed in future classes. For example: abstract class content { $title; $description function get_data($website){ } function common_function2() { } function common_function3() { } } class calendar_event extends content { $start_date; function validate_dates(){ } } Or would I use an interface and, because these are so similar, create a structure that each of the subclasses are forced to use for integrity reasons, and leave it up to the end developer who fleshes out that class to be responsible for each of the details of even the common functions. my thinking there is that some 'common' functions may need to be tweaked in the future for the needs of their specific class. Despite all that above, if you believe I am misunderstanding the what and why of abstracts and interfaces altogether, by all means let a valid answer to be stop thinking in this direction and suggest the proper way to move forward! Thanks!

  Read the article

• Ubuntu is booting on acer e1-510 laptop, but screen displays nothing

  - by user287602

  Tried loading ubuntu 12.04 (32-bit as well 64 bit) through bootable usb , on a brand new 64-bit acer E1-510 laptop. It shows the 'Try ubuntu without installing screen' and I selected that option. But instead of showing ubuntu's logo(which implies it is loading). I get a blank screen. The screen is on, but it shows nothing. I tried the same on an old model laptop acer aspire 5738 and it worked like a charm. However, I realized that Ubuntu is actually booting on E1-510 and only the display is not working. How did I arrive at this conclusion? When I select on 'Try ubuntu without installing screen', after about 8-10 seconds I see that the WiFi indicator light on the laptop panel switches on(just like when we boot up a Windows OS or even Ubuntu ). I got an idea that the system booted Ubuntu. To confirm this, I tried to adjust volume using keyboard shortcuts. Voila, I can hear the sound of adjusting volume! That means it has already booted Ubuntu. I confirmed this with another step. I pressed the power button once and after two seconds I pressed ENTER. It began the process of switching off and within 5 seconds the laptop was powered off. You may ask, Why is this a confirmation that Ubuntu has booted? This is because in Ubuntu when you press on power button, a dialog box opens with shut down, restart, suspend option- and the shut down option is already selected by default; so all I have to do is press ENTER to shut down. This again proved that Ubuntu was indeed up and running. Unlike previous 'AskUbunutu' posts about Acer e1-510, I must mention that my laptop came WITH the Legacy BIOS mode, so its not really a problem to boot ubuntu from a bootable pendrive. Only the screen is not working. In case you need to know, I am running Windows 7-Ultimate 64 bit on acer e1-510.

  Read the article

• Wrong statistics in AUX_STATS$ might puzzle the optimizer

  - by Mike Dietrich

  We do recommend the creation of System Statistics for quite a long time. Since Oracle 9i the optimizer works with a CPU and IO cost based model. And in order to give the optimizer some knowledge about the IO subsystem's performance and throughput - once System Statistics are collected - they'll get stored in AUX_STATS$. For this purpose in the old Oracle 9i days some default values had been defined - and you'll still find those defaults in Oracle Database 11g Release 2 in AUX_STATS$. But these old values don't reflect the performance of modern IO systems. So it might be a good best practice post upgrade to create fresh System Statistics if you haven't done this before.  You can collect System Statistics with: exec DBMS_STATS.GATHER_SYSTEM_STATS('start'); and end it later by executing: exec DBMS_STATS.GATHER_SYSTEM_STATS('stop'); You could also run DBMS_STATS.GATHER_SYSTEM_STATS('interval', interval=>N) instead where N is the number of minutes when statistics gathering is stopped automatically. Please make sure you'll do this on a real workload period. It won't make sense to gather these values while the database is in an idle state. You should do this ideally for several hours. It doesn't affect performance in a negative way as the values are anyway collected in V$SYSSTAT and V$SESSTAT. And in case you'd like to delete the stats and revert to the old default values you'd simply execute:exec DBMS_STATS.DELETE_SYSTEM_STATS; The tricky thing in Oracle Database 11.2 - and that's why I'm actually writing this blog post today - is bug9842771. This leads to wrong values in AUX_STATS$ for SREADTIM and MREADTIM by factor 1000 guiding the optimizer sometimes into the totally wrong directon. The workaround is to overwrite these values manually and divide them by 1000. Use the DBMS_STATS.SET_SYSTEM_STATS procedure. See this MOS Note:9842771.8 for the above bug for some further information. This issue is fixed in Oracle Database 11.2.0.3 and above. To get some background information about the statistics collected in please read this section in the Oracle Database 11.2 Performance Tuning Guide. And gathering System Statistics might have some implication if you have mixed workloads - and interacts with DB_FILE_MULTIBLOCK_READ_COUNT. For more information please read section 13.4.1.2.

  Read the article

• How do you automate a SharePoint 2010 deployment?

  - by Enrique Lima

  In the last couple of months SharePoint traffic (consulting, training and speaking) has picked up.  And with that also the requests for deployments.  There are good, great, bad and really bad things around this. But that is for another topic.  However part of the good and great has been the fact of organizations wanting to do a proof of concept deployment (even when WSS or MOSS has been deployed). We can go through a session (Microsoft has the SDPS concept, SharePoint Deployment Planning Services) of discovering what the customer wants to achieve from their investment in the platform and then also proceed to model the solution that would fit their needs.  But it should not stop there.  The next step should be a POC (as many have requested) to test out. Now, on to the meat of this post.  How do I deploy?  While it is a good process to watch and see all of it take place, not many have the time to sit through that.  Even more so, when that has been part of the description of deploying the platform in the sessions mentioned above. I will, though, break it into a deployment for development purposes and a deployment of a farm. Two tools (or scripts) for those two different types of deployment. First, let me address the development environment.  Around the last week in October, Chris Johnson (SharePoint Product Team) announced a SharePoint Easy Setup for Developers.  The kit itself will assist you in installing SharePoint Server (in standalone mode), the tools that go around Visual Studio, Expression Studio and the Office 2010 tools. Here is the link to Chris’ post: http://blogs.msdn.com/b/cjohnson/archive/2010/10/28/announcing-sharepoint-easy-setup-for-developers.aspx The other scenario is the use of a script in assisting you through the deployment of a farm. Now, this is not to override planning.  It should highlight the need for planning even more.  How?  Having your service accounts planned, the structure of the sites and the scale of your deployment.  Enter AutoSPInstaller.  This is a CodePlex project, and the intent behind this is not only to automate the installation but to give some meaning and get some sense out of what goes on during a SharePoint deployment. How?  Take for example the creation of the databases, when we do the initial OOB deployment by using the wizard, more times than not, we leave the names as they are.  How is that a “bad thing”?  Let’s make it a better practice to rename those Databases, and have them take on a name that is not “GUID-ized”. Having a better naming convention will not hurt, on the other hand will allow for consistency. Here is the link to AutoSPInstaller’s site on CodePlex: http://autospinstaller.codeplex.com/

  Read the article

• Design for an interface implementation that provides additional functionality

  - by Limbo Exile

  There is a design problem that I came upon while implementing an interface: Let's say there is a Device interface that promises to provide functionalities PerformA() and GetB(). This interface will be implemented for multiple models of a device. What happens if one model has an additional functionality CheckC() which doesn't have equivalents in other implementations? I came up with different solutions, none of which seems to comply with interface design guidelines: To add CheckC() method to the interface and leave one of its implementations empty: interface ISomeDevice { void PerformA(); int GetB(); bool CheckC(); } class DeviceModel1 : ISomeDevice { public void PerformA() { // do stuff } public int GetB() { return 1; } public bool CheckC() { bool res; // assign res a value based on some validation return res; } } class DeviceModel2 : ISomeDevice { public void PerformA() { // do stuff } public int GetB() { return 1; } public bool CheckC() { return true; // without checking anything } } This solution seems incorrect as a class implements an interface without truly implementing all the demanded methods. To leave out CheckC() method from the interface and to use explicit cast in order to call it: interface ISomeDevice { void PerformA(); int GetB(); } class DeviceModel1 : ISomeDevice { public void PerformA() { // do stuff } public int GetB() { return 1; } public bool CheckC() { bool res; // assign res a value based on some validation return res; } } class DeviceModel2 : ISomeDevice { public void PerformA() { // do stuff } public int GetB() { return 1; } } class DeviceManager { private ISomeDevice myDevice; public void ManageDevice(bool newDeviceModel) { myDevice = (newDeviceModel) ? new DeviceModel1() : new DeviceModel2(); myDevice.PerformA(); int b = myDevice.GetB(); if (newDeviceModel) { DeviceModel1 newDevice = myDevice as DeviceModel1; bool c = newDevice.CheckC(); } } } This solution seems to make the interface inconsistent. For the device that supports CheckC(): to add the logic of CheckC() into the logic of another method that is present in the interface. This solution is not always possible. So, what is the correct design to be used in such cases? Maybe creating an interface should be abandoned altogether in favor of another design?

  Read the article

• ITT Corporation Goes Live on Oracle Sales and Marketing Cloud Service (Fusion CRM)!

  - by Richard Lefebvre

  Back in Q2 of FY12, a division of ITT invited Oracle to demo our CRM On Demand product while the group was considering Salesforce.com. Chris Porter, our Oracle Direct sales representative learned the players and their needs and began to develop relationships. We lost that deal, but not Chris's persistence. A few months passed and Chris called on the ITT Shape Cutting Division's Director of Sales to see how things were going. Chris was told that the plan was for the division to buy more Salesforce.com. In fact, he informed Chris that he had just sent his team to Salesforce.com training. During the conversation, Chris mentioned that our new Oracle Sales Cloud Service could run with Outlook. This caused the ITT Sales Director to reconsider the plan to move forward with our competition. Oracle was invited back to demo the Oracle Sales and Marketing Cloud Service (Fusion CRM) and after it concluded, the Director stated, "That just blew your competition away." The deal closed on June 5th , 2012 Our Oracle Platinum Partner, Intelenex, began the implementation with ITT on July 30th. We are happy to report that on September 18th, the ITT Shape Cutting Division successfully went live on Oracle Sales and Marketing Cloud Service (Fusion CRM). About: ITT is a diversified leading manufacturer of highly engineered critical components and customized technology solutions for growing industrial end-markets in energy infrastructure, electronics, aerospace and transportation. Building on its heritage of innovation, ITT partners with its customers to deliver enduring solutions to the key industries that underpin our modern way of life. Founded in 1920, ITT is headquartered in White Plains, NY, with 8,500 employees in more than 30 countries and sales in more than 125 countries. The ITT Shape Cutting Division provides plasma lasers and controls with the Burny, Kaliburn, and AMC brands. Oracle Fusion Products: Oracle Sales and Marketing Cloud Service (Fusion CRM) including: • Fusion CRM Base • Fusion Sales Cloud • Fusion Mobile and Desktop Integration • Automated Forecasting Adoption Model: SaaS Partner: Intelenex Business Drivers: The ITT Shape Cutting Division wanted to: better enable its Sales Force with email and mobile CRM capabilities simplify and automate its complex sales processes centrally manage and maintain customer contact information Why We Won: ITT was impressed with the feature-rich capabilities of Oracle Sales and Marketing Cloud Service (Fusion CRM), including sales performance management and integration. The company also liked the product's flexibility and scalability for future growth. Expected Benefits: Streamlined accurate forecasting Increased customer manageability Improved sales performance Better visibility to customer information

  Read the article

• What could be the best way to generalize data from Facebook and Twitter?

  - by Sjaak van der Heide

  I am not sure if this is the best subsite to ask this question, but I'm pretty sure it doesn't fit on the normal or facebook SO page... I've been asked to make a general API for connecting to several Social Media platforms (at the moment Facebook and Twitter). I have already realised both of them seperately. Meaning I retrieve the data I need from both Facebook and Twitter and hold the data in it's own dataclass. In my case a list of FacebookTimelineItems and a list of TwitterTimelineItems. now the hard part is taking the parts that are used in both (username, id, message and such) and make 1 general class that is eventually passed on to who/whatever sent the call to my API. these are two pics of the data classes I have: http://imageshack.us/photo/my-images/703/facebookdata.png/ http://imageshack.us/photo/my-images/204/twitterdata.png/ probably not 100% correct but it gives an idea what it looks like. Now I've been having several idea about how to go about and generalize the two, which is harder then I thought at first. Create an interface (TimelineItem) and let the other classes extend that one. this way I'll always be sure I have a class that contains at least the basic info I need. downside is that deserializing the JSON seems to be a nightmare. Use the two dataclasses I have and combine them into a new class afterwards, then pass that one back to whoever requested it. This would probably work but I get the idea it's not the best way to tackle this problem, and is pretty dodgy IF I get it working. Or, in case of the other two being nearly impossible. Keep the two seperated in the front end, and go sit in the corner crying because I've just figured out you can't lump together facebook and twitter... Note: I don't have to make the front end part (view), I just make sure the Model is nicely filled with data :) I hope I placed this in the right section, if I didn't I apologise and would like to know where I should go with my question. Thanks in advance for any replied/ideas/opinions on this.

  Read the article

• prism and multiple screens

  - by Avi

  OK - I am studying Prism a little because of a "free weekend" offer on Pluralsight. As this is proving too complex for me, I went to the Prism book and looked at the forward, and this is what it said: What comes after “Hello, World?” WPF and Silverlight developers are blessed with an abundance of excellent books... There’s no lack of tutorials on Model-View-ViewModel ... But they stop short of the guidance you need to deliver a non-trivial application in full. Your first screen goes well. You add a second screen and a third. Because you started your solution with the built-in “Navigation Application Template,” adding new screens feels like hanging shirts on a closet rod. You are on a roll. Until the harsh reality of real application requirements sets in. As it happens, your application has 30 screens not three. There’s no room on that closet rod for 30 screens. Some screens are modal pop-ups; you don’t navigate to a pop-up. Screens become interdependent such that user activity in one screen triggers changes that propagate throughout the UI. Some screens are optional; others are visible only to authorized users. Some screens are permanent, while other screens can be opened and closed at will. You discover that navigating back to a previously displayed screen creates a new instance. That’s not what you expected and, to your horror, the prior instance is gone along with the user’s unsaved changes. Now the issue is, I don't relate to this description. I've never been a UI programmer, but same as everyone else I'm using Windows apps such as MS-Office, and web sites such as Amazon, Facebook and StackExchange. And I look at these and I don't see many "so many screens" issues! Indeed, the only applications having many windows I can think of is Visual Studio. Maybe also Visio, a little. But take Word - You have a ribbon and a main window. Or take Facebook: You have those lists on the left (Favorites, Lists, Groups etc.), the status middle, the adds and then the Contacts sidebar. But it's only one page. Of course, I understand that in enterprise scenarios there are dashboad applications where multiple segments of the screen are updated from multiple non-related services. This I dig. But other scenarios? So - What am I missing? What is the "multiple screens" monster Pirsm is supposed to be the silver bullet solution for? Shoud I invest in studying Prism in addition to learning WPF or ASP.NET MVC?

  Read the article

• Releasing the new Sample Browser Phone app

  - by Jialiang

  Originally posted on: http://geekswithblogs.net/Jialiang/archive/2014/06/05/releasing-the-new-sample-browser-phone-app.aspx Starting its journey in 2010, Sample Browser is achieving its tetralogy by releasing a Windows Phone version Sample Browser today. The new Windows Phone app is the fourth milestone of Sample Browser since we released the desktop version and the Visual Studio version in 2012 and the Windows Store version in 2013. This time, by providing a sample browser designed for a ‘walking’ platform in response to MVPs’ suggestions during last year’s MVP Global Summit, we are literally putting a world of code samples "at developers’ fingertips”. If you like to have a code gallery of over 7000 quality code samples in your pocket, then click here to download our Windows Phone Sample Browser and start a fantastic mobile experience. With Windows Phone version Sample Browser and the Internet, you can search for code samples on MSDN at anytime and anywhere you want, 24/7 and–even to bed. You can also check code sample details and share them with your friends. Compared to the other 3 pieces in the tetralogy (desktop version, Visual Studio version, and the Windows Store version), the Windows Phone version Sample Browser sells itself for convenience and instant connectivity. For those who need to reach code samples under mobile circumstances where no PCs is available, Windows Phone version Sample Browser will definitely be the right service you are seeking for. Aside from sharing samples via emails as the other 3 do, the Windows Phone version Sample Browser also allows you to share the sample via SMS and Near Field Communication (NFC).   What's Next Currently, the Windows Phone Sample Browser only supports online MSDN code searching, but we already plan to upgrade Sample Browser to allow users to do ‘Bing code search’, and add and manage their private code snippets.  We will also upgrade the app to universal app. Universal App is a new concept brought up in the Microsoft Build Developer Conference 2014. It is a new development model that allows for a single app to be deployed across multiple Windows devices such as Windows Phone, Windows 8.1, and XBox. Therefore, once we finish upgrading Sample Browser to a universal app, you can synchronize your own code snippets across different devices; You can also mark a code sample as favorite on your Windows Phone and continue to study the sample when you are on your desktop. By then, sharing data between platforms will be a piece of cake. Also, the user experience of Sample Browser on different platforms will be more consistent.  The best is yet to come!   We sincerely suggest you give Sample Browser a try (click here to download). If you love what you see in Sample Browser, please recommend it to your friends and colleagues. If you encounter any problems or have any suggestions for us, please contact us at [email protected]. Your precious opinions and comments are more than welcome.

  Read the article

< Previous Page | 830 831 832 833 834 835 836 837 838 839 840 841  | Next Page >