Search Results

Search found 22668 results on 907 pages for 'command prompt'.

Page 862/907 | < Previous Page | 858 859 860 861 862 863 864 865 866 867 868 869  | Next Page >

• Sound issues after trying everything

  - by Lerp

  I cannot get my sound working properly, no matter what I do, there's always some problem. It's very annoying as it's the only thing preventing me from making Ubuntu my main OS. At the moment my sound always plays through both my speakers and my headphones regardless except the sound through the headphones is crackly. It is also a bit quiet even though everything is maxed. I've managed to improve the situation to a point where the sound out of my speakers is perfect but I have none at all from my headphones. I do have two connectors listed in the sound settings but regardless of which one is selected it always plays through the speakers. I think this might have something to do with the fact that my speakers are plugging into the front of my computer, typically the headphone jack, and my headphones are plugging into the back but when I try disconnecting the speakers from the front there is still no sound from the headphones. I fixed the speaker sound by going through the sound settings and making sure they were all set to 100% then rebooting. Things I have tried: Maxing everything and unmuting everything in alsamixer Uninstalling pulseaudio Making gstreamer use only alsa via gstreamer-properties. This worked with the sound test button including independent sound between headphones and speakers but when I reset the computer it no longer worked. So I tried setting it manually in gconf-editor which didn't work either. Reinstalling alsa and pulseaudio Setting the model in /etc/modprobe.d/alsa-base.conf to 6stack and 6stack-dig neither worked. Upgrading to 12.10 Here's some command output to help you diagnose my problem. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: AD198x Analog [AD198x Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: AD198x Digital [AD198x Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 2: AD198x Headphone [AD198x Headphone] Subdevices: 1/1 Subdevice #0: subdevice #0 sudo lshw -C sound *-multimedia description: Audio device product: 82801JI (ICH10 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:70 memory:f7ff8000-f7ffbfff cat /proc/asound/card*/codec* | grep "Codec" Codec: Analog Devices AD1989B cat /etc/modprobe.d/alsa-base.conf # autoloader aliases install sound-slot-0 /sbin/modprobe snd-card-0 install sound-slot-1 /sbin/modprobe snd-card-1 install sound-slot-2 /sbin/modprobe snd-card-2 install sound-slot-3 /sbin/modprobe snd-card-3 install sound-slot-4 /sbin/modprobe snd-card-4 install sound-slot-5 /sbin/modprobe snd-card-5 install sound-slot-6 /sbin/modprobe snd-card-6 install sound-slot-7 /sbin/modprobe snd-card-7 # Cause optional modules to be loaded above generic modules install snd /sbin/modprobe --ignore-install snd $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-ioctl32 ; /sbin/modprobe --quiet --use-blacklist snd-seq ; } # # Workaround at bug #499695 (reverted in Ubuntu see LP #319505) install snd-pcm /sbin/modprobe --ignore-install snd-pcm $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-pcm-oss ; : ; } install snd-mixer /sbin/modprobe --ignore-install snd-mixer $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-mixer-oss ; : ; } install snd-seq /sbin/modprobe --ignore-install snd-seq $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; /sbin/modprobe --quiet --use-blacklist snd-seq-oss ; : ; } # install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; : ; } # Cause optional modules to be loaded above sound card driver modules install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-emu10k1-synth ; } install snd-via82xx /sbin/modprobe --ignore-install snd-via82xx $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq ; } # Load saa7134-alsa instead of saa7134 (which gets dragged in by it anyway) install saa7134 /sbin/modprobe --ignore-install saa7134 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist saa7134-alsa ; : ; } # Prevent abnormal drivers from grabbing index 0 options bt87x index=-2 options cx88_alsa index=-2 options saa7134-alsa index=-2 options snd-atiixp-modem index=-2 options snd-intel8x0m index=-2 options snd-via82xx-modem index=-2 options snd-usb-audio index=-2 options snd-usb-caiaq index=-2 options snd-usb-ua101 index=-2 options snd-usb-us122l index=-2 options snd-usb-usx2y index=-2 # Ubuntu #62691, enable MPU for snd-cmipci options snd-cmipci mpu_port=0x330 fm_port=0x388 # Keep snd-pcsp from being loaded as first soundcard options snd-pcsp index=-2 # Keep snd-usb-audio from beeing loaded as first soundcard options snd-usb-audio index=-2 options snd-hda-intel model=6stack

  Read the article

• HP Pavilion tx2000 - Wifi adapter no longer works after moving from 12.04 to a 12.10 clean install

  - by Marek L.

  I have a HP Pavilion tx2000 that I have been running Ubuntu 12.04 on for a couple of months without any problems (wifi worked great) until yesterday when my hard drive failed. I replaced the hard drive and decided to install Ubuntu 12.10. Unlike 12.04, the wifi did not work after the installation finished and all the updates where installed (over Ethernet). The network drop down in the top right didn't even show a wireless option. I Googled about for a bit and found some solutions that seemed like they might work. Unfortunately they did not. Here is what I tried: sudo apt-get remove bcmwl-kernel-source sudo apt-get install b43-fwcutter sudo apt-get install firmware-b43-lpphy-installer Restart the computer. And the wifi still didn't work. At which point I panicked a bit and tried to undo the previous commands by running: sudo apt-get remove b43-fwcutter firmware-b43-lpphy-installer sudo apt-get install bcmwl-kernel-source Restart the computer. The wifi still doesn't work. This is where I stopped because I have no idea what I am doing and don't want to mess something up. The network drop down still doesn't show a wireless option and the hardware wifi switch on the laptop is amber (it turns blue when the wifi is on). Using the hardware switch does not change the color. Output from: sudo lspci ... 08:00.0 Network controller: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller (rev 01) ... Output from: sudo lshw -class network *-network UNCLAIMED description: Network controller product: BCM4322 802.11a/b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d1100000-d1103fff ... Output from: sudo rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes UPDATE: After writing up this question tried the following command: sudo rfkill unblock all At first it didn't do anything but after running it about four times, sudo rfkill list all now returns: 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no But the network menu still does not have a wireless option and the hardware switch still glows amber. Pushing the hardware switch turns the hard block back on and I have to run sudo rfkill unblock all multiple times again to turn it off. Any help is appreciated! Update 2: Full output from sudo lspci -nn: 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600] 00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) [1022:9602] 00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0) [1022:9604] 00:05.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1) [1022:9605] 00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) [1022:9606] 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] 00:12.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:12.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:12.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:13.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:13.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:13.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller [1002:4385] (rev 3a) 00:14.1 IDE interface [0101]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] 00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) [1002:4383] 00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] 00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge [1002:4384] 00:14.5 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399] 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor HyperTransport Configuration [1022:1300] (rev 40) 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Address Map [1022:1301] 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor DRAM Controller [1022:1302] 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Miscellaneous Control [1022:1303] 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Link Control [1022:1304] 01:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RS780M/RS780MN [Mobility Radeon HD 3200 Graphics] [1002:9612] 08:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01) 09:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)

  Read the article

• Using Windows Previous Versions to access ZFS Snapshots (July 14, 2009)

  - by user12612012

  The Previous Versions tab on the Windows desktop provides a straightforward, intuitive way for users to view or recover files from ZFS snapshots.  ZFS snapshots are read-only, point-in-time instances of a ZFS dataset, based on the same copy-on-write transactional model used throughout ZFS.  ZFS snapshots can be used to recover deleted files or previous versions of files and they are space efficient because unchanged data is shared between the file system and its snapshots.  Snapshots are available locally via the .zfs/snapshot directory and remotely via Previous Versions on the Windows desktop. Shadow Copies for Shared Folders was introduced with Windows Server 2003 but subsequently renamed to Previous Versions with the release of Windows Vista and Windows Server 2008.  Windows shadow copies, or snapshots, are based on the Volume Snapshot Service (VSS) and, as the [Shared Folders part of the] name implies, are accessible to clients via SMB shares, which is good news when using the Solaris CIFS Service.  And the nice thing is that no additional configuration is required - it "just works". On Windows clients, snapshots are accessible via the Previous Versions tab in Windows Explorer using the Shadow Copy client, which is available by default on Windows XP SP2 and later.  For Windows 2000 and pre-SP2 Windows XP, the client software is available for download from Microsoft: Shadow Copies for Shared Folders Client. Assuming that we already have a shared ZFS dataset, we can create ZFS snapshots and view them from a Windows client. zfs snapshot tank/home/administrator@snap101zfs snapshot tank/home/administrator@snap102 To view the snapshots on Windows, map the dataset on the client then right click on a folder or file and select Previous Versions.  Note that Windows will only display previous versions of objects that differ from the originals.  So you may have to modify files after creating a snapshot in order to see previous versions of those files. The screenshot above shows various snapshots in the Previous Versions window, created at different times.  On the left panel, the .zfs folder is visible, illustrating that this is a ZFS share.  The .zfs setting can be toggled as desired, it makes no difference when using previous versions.  To make the .zfs folder visible: zfs set snapdir=visible tank/home/administrator To hide the .zfs folder: zfs set snapdir=hidden tank/home/administrator The following screenshot shows the Previous Versions panel when a file has been selected.  In this case the user is prompted to view, copy or restore the file from one of the available snapshots. As can be seen from the screenshots above, the Previous Versions window doesn't display snapshot names: snapshots are listed by snapshot creation time, sorted in time order from most recent to oldest.  There's nothing we can do about this, it's the way that the interface works.  Perhaps one point of note, to avoid confusion, is that the ZFS snapshot creation time isnot the same as the root directory creation timestamp. In ZFS, all object attributes in the original dataset are preserved when a snapshot is taken, including the creation time of the root directory.  Thus the root directory creation timestamp is the time that the directory was created in the original dataset. # ls -d% all /home/administrator         timestamp: atime         Mar 19 15:40:23 2009         timestamp: ctime         Mar 19 15:40:58 2009         timestamp: mtime         Mar 19 15:40:58 2009         timestamp: crtime         Mar 19 15:18:34 2009 # ls -d% all /home/administrator/.zfs/snapshot/snap101         timestamp: atime         Mar 19 15:40:23 2009         timestamp: ctime         Mar 19 15:40:58 2009         timestamp: mtime         Mar 19 15:40:58 2009         timestamp: crtime         Mar 19 15:18:34 2009 The snapshot creation time can be obtained using the zfs command as shown below. # zfs get all tank/home/administrator@snap101NAME                             PROPERTY  VALUEtank/home/administrator@snap101  type      snapshottank/home/administrator@snap101  creation  Mon Mar 23 18:21 2009 In this example, the dataset was created on March 19th and the snapshot was created on March 23rd. In conclusion, Shadow Copies for Shared Folders provides a straightforward way for users to view or recover files from ZFS snapshots.  The Windows desktop provides an easy to use, intuitive GUI and no configuration is required to use or access previous versions of files or folders. REFERENCES FOR MORE INFORMATION ZFS ZFS Learning Center Introduction to Shadow Copies of Shared Folders Shadow Copies for Shared Folders Client

  Read the article

• Computer Networks UNISA - Chap 15 &ndash; Network Management

  - by MarkPearl

  After reading this section you should be able to Understand network management and the importance of documentation, baseline measurements, policies, and regulations to assess and maintain a network’s health. Manage a network’s performance using SNMP-based network management software, system and event logs, and traffic-shaping techniques Identify the reasons for and elements of an asset managements system Plan and follow regular hardware and software maintenance routines Fundamentals of Network Management Network management refers to the assessment, monitoring, and maintenance of all aspects of a network including checking for hardware faults, ensuring high QoS, maintaining records of network assets, etc. Scope of network management differs depending on the size and requirements of the network. All sub topics of network management share the goals of enhancing the efficiency and performance while preventing costly downtime or loss. Documentation The way documentation is stored may vary, but to adequately manage a network one should at least record the following… Physical topology (types of LAN and WAN topologies – ring, star, hybrid) Access method (does it use Ethernet 802.3, token ring, etc.) Protocols Devices (Switches, routers, etc) Operating Systems Applications Configurations (What version of operating system and config files for serve / client software) Baseline Measurements A baseline is a report of the network’s current state of operation. Baseline measurements might include the utilization rate for your network backbone, number of users logged on per day, etc. Baseline measurements allow you to compare future performance increases or decreases caused by network changes or events with past network performance. Obtaining baseline measurements is the only way to know for certain whether a pattern of usage has changed, or whether a network upgrade has made a difference. There are various tools available for measuring baseline performance on a network. Policies, Procedures, and Regulations Following rules helps limit chaos, confusion, and possibly downtime. The following policies and procedures and regulations make for sound network management. Media installations and management (includes designing physical layout of cable, etc.) Network addressing policies (includes choosing and applying a an addressing scheme) Resource sharing and naming conventions (includes rules for logon ID’s) Security related policies Troubleshooting procedures Backup and disaster recovery procedures In addition to internal policies, a network manager must consider external regulatory rules. Fault and Performance Management After documenting every aspect of your network and following policies and best practices, you are ready to asses you networks status on an on going basis. This process includes both performance management and fault management. Network Management Software To accomplish both fault and performance management, organizations often use enterprise-wide network management software. There various software packages that do this, each collect data from multiple networked devices at regular intervals, in a process called polling. Each managed device runs a network management agent. So as not to affect the performance of a device while collecting information, agents do not demand significant processing resources. The definition of a managed devices and their data are collected in a MIB (Management Information Base). Agents communicate information about managed devices via any of several application layer protocols. On modern networks most agents use SNMP which is part of the TCP/IP suite and typically runs over UDP on port 161. Because of the flexibility and sophisticated network management applications are a challenge to configure and fine-tune. One needs to be careful to only collect relevant information and not cause performance issues (i.e. pinging a device every 5 seconds can be a problem with thousands of devices). MRTG (Multi Router Traffic Grapher) is a simple command line utility that uses SNMP to poll devices and collects data in a log file. MRTG can be used with Windows, UNIX and Linux. System and Event Logs Virtually every condition recognized by an operating system can be recorded. This is typically done using event logs. In Windows there is a GUI event log viewer. Similar information is recorded in UNIX and Linux in a system log. Much of the information collected in event logs and syslog files does not point to a problem, even if it is marked with a warning so it is important to filter your logs appropriately to reduce the noise. Traffic Shaping When a network must handle high volumes of network traffic, users benefit from performance management technique called traffic shaping. Traffic shaping involves manipulating certain characteristics of packets, data streams, or connections to manage the type and amount of traffic traversing a network or interface at any moment. Its goals are to assure timely delivery of the most important traffic while offering the best possible performance for all users. Several types of traffic prioritization exist including prioritizing traffic according to any of the following characteristics… Protocol IP address User group DiffServr VLAN tag in a Data Link layer frame Service or application Caching In addition to traffic shaping, a network or host might use caching to improve performance. Caching is the local storage of frequently needed files that would otherwise be obtained from an external source. By keeping files close to the requester, caching allows the user to access those files quickly. The most common type of caching is Web caching, in which Web pages are stored locally. To an ISP, caching is much more than just convenience. It prevents a significant volume of WAN traffic, thus improving performance and saving money. Asset Management Another key component in managing networks is identifying and tracking its hardware. This is called asset management. The first step to asset management is to take an inventory of each node on the network. You will also want to keep records of every piece of software purchased by your organization. Asset management simplifies maintaining and upgrading the network chiefly because you know what the system includes. In addition, asset management provides network administrators with information about the costs and benefits of certain types of hardware or software. Change Management Networks are always in a stage of flux with various aspects including… Software changes and patches Client Upgrades Shared Application Upgrades NOS Upgrades Hardware and Physical Plant Changes Cabling Upgrades Backbone Upgrades For a detailed explanation on each of these read the textbook (Page 750 – 761)

  Read the article

• The Linux powered LAN Gaming House

  - by sachinghalot

  LAN parties offer the enjoyment of head to head gaming in a real-life social environment. In general, they are experiencing decline thanks to the convenience of Internet gaming, but Kenton Varda is a man who takes his LAN gaming very seriously. His LAN gaming house is a fascinating project, and best of all, Linux plays a part in making it all work.Varda has done his own write ups (short, long), so I'm only going to give an overview here. The setup is a large house with 12 gaming stations and a single server computer.The client computers themselves are rack mounted in a server room, and they are linked to the gaming stations on the floor above via extension cables (HDMI for video and audio and USB for mouse and keyboard). Each client computer, built into a 3U rack mount case, is a well specced gaming rig in its own right, sporting an Intel Core i5 processor, 4GB of RAM and an Nvidia GeForce 560 along with a 60GB SSD drive.Originally, the client computers ran Ubuntu Linux rather than Windows and the games executed under WINE, but Varda had to abandon this scheme. As he explains on his site:"Amazingly, a majority of games worked fine, although many had minor bugs (e.g. flickering mouse cursor, minor rendering artifacts, etc.). Some games, however, did not work, or had bad bugs that made them annoying to play."Subsequently, the gaming computers have been moved onto a more conventional gaming choice, Windows 7. It's a shame that WINE couldn't be made to work, but I can sympathize as it's rare to find modern games that work perfectly and at full native speed. Another problem with WINE is that it tends to suffer from regressions, which is hardly surprising when considering the difficulty of constantly improving the emulation of the Windows API. Varda points out that he preferred working with Linux clients as they were easier to modify and came with less licensing baggage.Linux still runs the server and all of the tools used are open source software. The hardware here is a Intel Xeon E3-1230 with 4GB of RAM. The storage hanging off this machine is a bit more complex than the clients. In addition to the 60GB SSD, it also has 2x1TB drives and a 240GB SDD.When the clients were running Linux, they booted over PXE using a toolchain that will be familiar to anyone who has setup Linux network booting. DHCP pointed the clients to the server which then supplied PXELINUX using TFTP. When booted, file access was accomplished through network block device (NBD). This is a very easy to use system that allows you to serve the contents of a file as a block device over the network. The client computer runs a user mode device driver and the device can be mounted within the file system using the mount command.One snag with offering file access via NBD is that it's difficult to impose any security restrictions on different areas of the file system as the server only sees a single file. The advantage is perfomance as the client operating system simply sees a block device, and besides, these security issues aren't relevant in this setup.Unfortunately, Windows 7 can't use NBD, so, Varda had to switch to iSCSI (which works in both server and client mode under Linux). His network cards are not compliant with this standard when doing a netboot, but fortunately, gPXE came to the rescue, and he boostraps it over PXE. gPXE is also available as an ISO image and is worth knowing about if you encounter an awkward machine that can't manage a network boot. It can also optionally boot from a HTTP server rather than the more traditional TFTP server.According to Varda, booting all 12 machines over the Gigabit Ethernet network is surprisingly fast, and once booted, the machines don't seem noticeably slower than if they were using local storage. Once loaded, most games attempt to load in as much data as possible, filling the RAM, and the the disk and network bandwidth required is small. It's worth noting that these are aspects of this project that might differ from some other thin client scenarios.At time of writing, it doesn't seem as though the local storage of the client machines is being utilized. Instead, the clients boot into Windows from an image on the server that contains the operating system and the games themselves. It uses the copy on write feature of LVM so that any writes from a client are added to a differencing image allocated to that client. As the administrator, Varda can log into the Linux server and authorize changes to the master image for updates etc.SummaryOverall, Varda estimates the total cost of the project at about $40,000, and of course, he needed a property that offered a large physical space in order to house the computers and the gaming workstations. Obviously, this project has stark differences to most thin client projects. The balance between storage, network usage, GPU power and security would not be typical of an office installation, for example. The only letdown is that WINE proved to be insufficiently compatible to run a wide variety of modern games, but that is, perhaps, asking too much of it, and hats off to Varda for trying to make it work.

  Read the article

• Swap partition not recognized (The disk drive with UUID=... is not ready yet or not present)

  - by ladaghini

  I think I had an encrypted swap partition, because I chose to encrypt my home directory during the installation. I believe that's what the line with /dev/mapper/cryptswap1 ... in my /etc/fstab is all about. I did something to bork my swap because on the next boot, I got a message (paraphrased): The disk drive for /dev/mapper/cryptswap1 is not ready yet or not present. Wait to continue. Press S to skip or M to manually recover. (As a side note, pressing S or M seemed to do nothing different from just waiting.) Here's what I've tried: This tutorial on how to fix the swap partition not mounting. However, in the above, the mkswap command fails because the device is busy. So I booted from a live USB, ran GParted to reformat the swap partition (which showed up as an unknown fs type), and chrooted into the broken system to try that tutorial again. I also adjusted /etc/initramfs-tools/conf.d/resume and /etc/fstab to reflect the new UUID generated from formatting the partition as a swap. That still didn't work; instead of /dev/mapper/cryptswap1 not present, "The disk drive with UUID=[swap partition's UUID] is not ready yet or not present..." So I decided to start afresh as though I never had created a swap partition in the first place. From the Live USB, I deleted the swap partition altogether (which, again showed up in GParted as an unknown fs type), removed the swap and cryptswap entries in /etc/fstab as well as removed /etc/initramfs-tools/conf.d/resume and /etc/crypttab. At this point the main system shouldn't be considered broken because there is no swap partition and no instructions to mount one, right? I didn't get any errors during startup. I followed the same instructions to create and encrypt the swap partition, starting with creating a partition for the swap, though I think fdisk said a reboot was necessary to see changes. I was confident the 3rd process above would work, but the problem yet persists. Some relevant info (/dev/sda8 is the swap partition): /etc/fstab file: # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda6 during installation UUID=4c11e82c-5fe9-49d5-92d9-cdaa6865c991 / ext4 errors=remount-ro 0 1 # /boot was on /dev/sda5 during installation UUID=4031413e-e89f-49a9-b54c-e887286bb15e /boot ext4 defaults 0 2 # /home was on /dev/sda7 during installation UUID=d5bbfc6f-482a-464e-9f26-fd213230ae84 /home ext4 defaults 0 2 # swap was on /dev/sda8 during installation UUID=5da2c720-8787-4332-9317-7d96cf1e9b80 none swap sw 0 0 /dev/mapper/cryptswap1 none swap sw 0 0 output of sudo mount: /dev/sda6 on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda5 on /boot type ext4 (rw) /dev/sda7 on /home type ext4 (rw) /home/undisclosed/.Private on /home/undisclosed type ecryptfs (ecryptfs_check_dev_ruid,ecryptfs_cipher=aes,ecryptfs_key_bytes=16,ecryptfs_unlink_sigs,ecryptfs_sig=cbae1771abd34009,ecryptfs_fnek_sig=7cefe2f59aab8e58) gvfs-fuse-daemon on /home/undisclosed/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=undisclosed) output of sudo blkid (note that /dev/sda8 is missing): /dev/sda1: LABEL="SYSTEM" UUID="960490E80490CC9D" TYPE="ntfs" /dev/sda2: UUID="D4043140043126C0" TYPE="ntfs" /dev/sda3: LABEL="Shared" UUID="80F613E1F613D5EE" TYPE="ntfs" /dev/sda5: UUID="4031413e-e89f-49a9-b54c-e887286bb15e" TYPE="ext4" /dev/sda6: UUID="4c11e82c-5fe9-49d5-92d9-cdaa6865c991" TYPE="ext4" /dev/sda7: UUID="d5bbfc6f-482a-464e-9f26-fd213230ae84" TYPE="ext4" /dev/mapper/cryptswap1: UUID="41fa147a-3e2c-4e61-b29b-3f240fffbba0" TYPE="swap" output of sudo fdisk -l: Disk /dev/mapper/cryptswap1 doesn't contain a valid partition table Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xdec3fed2 Device Boot Start End Blocks Id System /dev/sda1 * 2048 409599 203776 7 HPFS/NTFS/exFAT /dev/sda2 409600 210135039 104862720 7 HPFS/NTFS/exFAT /dev/sda3 210135040 415422463 102643712 7 HPFS/NTFS/exFAT /dev/sda4 415424510 625141759 104858625 5 Extended /dev/sda5 415424512 415922175 248832 83 Linux /dev/sda6 415924224 515921919 49998848 83 Linux /dev/sda7 515923968 621389823 52732928 83 Linux /dev/sda8 621391872 625141759 1874944 82 Linux swap / Solaris Disk /dev/mapper/cryptswap1: 1919 MB, 1919942656 bytes 255 heads, 63 sectors/track, 233 cylinders, total 3749888 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xaf5321b5 /etc/initramfs-tools/conf.d/resume file: RESUME=UUID=5da2c720-8787-4332-9317-7d96cf1e9b80 /etc/crypttab file: cryptswap1 /dev/sda8 /dev/urandom swap,cipher=aes-cbc-essiv:sha256 output of sudo swapon -as: Filename Type Size Used Priority /dev/mapper/cryptswap1 partition 1874940 0 -1 output of sudo free -m: total used free shared buffers cached Mem: 1476 1296 179 0 35 671 -/+ buffers/cache: 590 886 Swap: 1830 0 1830 So, how can this be fixed?

  Read the article

• Installing Ubuntu 12.04.1 x64 with Fake RAID 1 [SOLVED]

  - by Arkadius

  I had: Software: Dual boot with Windows XP Ubuntu 10.04 LTS x32 Hardware Fake RAID 1 (mirroring) with 2x1 TB: Partition 1 - Windows Partition 2 - SWAP Partition 3 - / (root) Partition 4 - Extended Partition 5 - /home Partition 6 - /data arek@domek:/var/log/installer$ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000de1b9 Device Boot Start End Blocks Id System /dev/sda1 * 63 524297339 262148638+ 7 HPFS/NTFS/exFAT /dev/sda2 524297340 528506369 2104515 82 Linux swap / Solaris /dev/sda3 528506370 570468149 20980890 83 Linux /dev/sda4 570468150 1953118439 691325145 5 Extended /dev/sda5 570468213 675340469 52436128+ 83 Linux /dev/sda6 675340533 1953118439 638888953+ 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000de1b9 Device Boot Start End Blocks Id System /dev/sdb1 * 63 524297339 262148638+ 7 HPFS/NTFS/exFAT /dev/sdb2 524297340 528506369 2104515 82 Linux swap / Solaris /dev/sdb3 528506370 570468149 20980890 83 Linux /dev/sdb4 570468150 1953118439 691325145 5 Extended /dev/sdb5 570468213 675340469 52436128+ 83 Linux /dev/sdb6 675340533 1953118439 638888953+ 83 Linux arek@domek:/var/log/installer$ ls -l /dev/mapper/ total 0 crw------- 1 root root 10, 236 Oct 7 20:17 control lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha -> ../dm-0 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha1 -> ../dm-1 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha2 -> ../dm-2 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha3 -> ../dm-3 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha4 -> ../dm-4 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha5 -> ../dm-5 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha6 -> ../dm-6 I wanted to upgrade from 10.04 x32 to 12.04 x64 using FRESH installation. So, run installation of Ubuntu 12.04.1 x64 LTS using alternate CD. During the installation I selected manual partitioning and to: - Use and Format / (root) - Use and Format SWAP - Use and Keep data on /home - Use and Keep data on /data After I clicked "Continue" I get error creating and formatting SWAP partition. I go to terminal with Alt + F2 (?) and hit enter. I discovered that there was visible RAID as only disk with NO partitions. Something like this: arek@domek:/var/log/installer$ ls -l /dev/mapper/ lrwxrwxrwx 1 root root 7 Oct 7 20:17 /dev/mapper/pdc_jhjbcaha -> ../dm-0 arek@domek:/var/log/installer$ ls -l /dev/dm* brw-rw---- 1 root disk 252, 0 Oct 7 20:17 /dev/dm-0 So I switched to log console Alt+F3 (?) and saw errors like below: Oct 7 14:02:45 check-missing-firmware: /dev/.udev/firmware-missing does not exist, skipping Oct 7 14:02:45 check-missing-firmware: /run/udev/firmware-missing does not exist, skipping Oct 7 14:02:45 check-missing-firmware: no missing firmware in /dev/.udev/firmware-missing /run/udev/firmware-missing Oct 7 14:02:45 anna-install: Installing dmraid-udeb Oct 7 14:02:45 anna[12599]: DEBUG: retrieving dmraid-udeb 1.0.0.rc16-4.1ubuntu8 Oct 7 14:02:49 anna[12599]: DEBUG: retrieving libdmraid1.0.0.rc16-udeb 1.0.0.rc16-4.1ubuntu8 Oct 7 14:02:49 anna[12599]: DEBUG: retrieving kpartx-udeb 0.4.9-3ubuntu5 Oct 7 14:02:49 disk-detect: Serial ATA RAID disk(s) detected. Oct 7 14:02:55 disk-detect: Enabling dmraid support. Oct 7 14:02:55 disk-detect: RAID set "pdc_jhjbcaha" was activated Oct 7 14:02:55 HERE --> dmraid-activate: ERROR: Cannot retrieve RAID set information for pdc_jhjbcaha Oct 7 14:02:56 check-missing-firmware: /dev/.udev/firmware-missing does not exist, skipping Oct 7 14:02:56 check-missing-firmware: /run/udev/firmware-missing does not exist, skipping Oct 7 14:02:56 check-missing-firmware: no missing firmware in /dev/.udev/firmware-missing /run/udev/firmware-missing Oct 7 14:02:57 main-menu[428]: DEBUG: resolver (libnewt0.52): package doesn't exist (ignored) Oct 7 14:02:57 main-menu[428]: DEBUG: resolver (ext2-modules): package doesn't exist (ignored) Oct 7 14:02:57 main-menu[428]: INFO: Menu item 'partman-base' selected Oct 7 14:02:57 kernel: [ 316.512999] NTFS driver 2.1.30 [Flags: R/O MODULE]. Oct 7 14:02:57 kernel: [ 316.523221] Btrfs loaded Oct 7 14:02:57 kernel: [ 316.534781] JFS: nTxBlock = 8192, nTxLock = 65536 Oct 7 14:02:57 kernel: [ 316.554749] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled Oct 7 14:02:57 kernel: [ 316.555336] SGI XFS Quota Management subsystem Oct 7 14:02:58 md-devices: mdadm: No arrays found in config file or automatically Oct 7 14:02:58 partman: No matching physical volumes found Oct 7 14:02:58 partman: No volume groups found Oct 7 14:02:58 partman: Reading all physical volumes. This may take a while... Oct 7 14:02:58 partman-lvm: No volume groups found Oct 7 14:02:58 partman: Error running 'tune2fs -l /dev/mapper/pdc_jhjbcaha' Oct 7 14:02:58 partman: Error running 'tune2fs -l /dev/mapper/pdc_jhjbcaha' Oct 7 14:02:58 partman: Error running 'tune2fs -l /dev/mapper/pdc_jhjbcaha' Oct 7 14:06:11 HERE --> partman: mkswap: can't open '/dev/mapper/pdc_jhjbcaha2': No such file or directory Oct 7 14:07:28 init: starting pid 401, tty '/dev/tty2': '-/bin/sh' Oct 7 14:15:00 net/hw-detect.hotplug: Detected hotpluggable network interface eth0 Oct 7 14:15:00 net/hw-detect.hotplug: Detected hotpluggable network interface lo As You can see there are 2 errors Oct 7 14:02:55 dmraid-activate: ERROR: Cannot retrieve RAID set information for pdc_jhjbcaha and Oct 7 14:06:11 partman: mkswap: can't open '/dev/mapper/pdc_jhjbcaha2': No such file or directory I looked in the internet and try to run command "dmraid -ay" and get something like that: dmraid -ay /dev/mapper/pdc_jhjbcaha -> Already activated /dev/mapper/pdc_jhjbcaha1 -> Successfully activated /dev/mapper/pdc_jhjbcaha2 -> Successfully activated /dev/mapper/pdc_jhjbcaha3 -> Successfully activated /dev/mapper/pdc_jhjbcaha4 -> Successfully activated /dev/mapper/pdc_jhjbcaha5 -> Successfully activated /dev/mapper/pdc_jhjbcaha6 -> Successfully activated Then I returned to installer with Alt+F1 (?) and click "Return" to return to partitioning menu. I did NOT change anything just selected again "Continue" and everything goes smoothly. I hope this will help someone. arkadius

  Read the article

• How to move MOSS 2007 to another SharePoint Farm

  - by DipeshBhanani

  It was time of my first onsite client assignment on SharePoint. Client had one server production environment. They wanted to upgrade the topology with completely new SharePoint Farm of three servers. So, the task was to move whole MOSS 2007 stuff to the new server environment without impacting data. The last three words “… without impacting data…” were actually putting pressure on my head. Moreover SSP was required to move because additional information has been added for users apart from AD import.   I thought I had to do only backup and restore. It appeared pretty easy at first thought. Just because of these three damn scary words, I thought to check out on internet for guidance related to this scenario. I couldn’t get anything except general guidance of moving server on Microsoft TechNet site. I promised myself for starting blogs with this post if I would be successful in this task. Well, I took long time to write this but finally made it. I hope it will be useful to all guys looking for SharePoint server movement.   Before beginning restoration, make sure that, there is no difference in versions of SharePoint at source and destination server. Also check whether the state of SharePoint Installation at the time of backup and restore is same or not. (E.g. SharePoint related service packs and patches if any)   The main tasks of the server movement are as follow:   1.        Backup all the databases 2.        Install and configure SharePoint on new environment 3.        Deploy all solutions (WSP Files) globally to destination server- for installing features attached to the solutions 4.        Install all the custom features 5.        Deploy/Copy custom pages/files which are added to the “12Hive” folder later 6.        Restore SSP 7.        Restore My Site 8.        Restore other web application   Tasks 3 to 5 are for making sure that we have configured the environment well enough for the web application to be restored successfully. The main and complex task was restoring SSP. I have started restoring SSP through Central Admin. After a while, the restoration status was updated to “unsuccessful”. “Damn it, what went wrong?” I thought looking at the error detail down the page. I couldn’t remember the error message but I had corrected and restored it again.   Actually once you fail restoring SSP, until and unless you don’t clean all related stuff well, your restoration will be failed again and again. I wanted to find the actual reason. So cleaned, restored, cleaned, restored… I had tried almost 5-6 times and finally, I succeeded. I had realized how pleasant it is, to see the word “Successful” on the screen. Without wasting your much time to read, let me write all the detailed steps of restoring SSP:   1.        Delete the SSP through following STSADM command. stsadm -o deletessp -title <SSP name> -deletedatabases -force e.g.: stsadm -o deletessp -title SharedServices1 -deletedatabases –force 2.        Check and delete the web application associated with SSP if it exists. 3.        Remove Link from Check and remove “Alternate Access Mapping” associated with SSP if it exists. 4.        Check and delete IIS site as well as application pool associated with SSP if it exists. 5.        Stop following services: ·         Office SharePoint Server Search ·         Windows SharePoint Services Search ·         Windows SharePoint Services Help Search   6.        Delete all the databases associated/related to SSP from SQL Server. 7.        Reset IIS. 8.        Start again following services: ·         Office SharePoint Server Search ·         Windows SharePoint Services Search ·         Windows SharePoint Services Help Search   9.        Restore the new SSP.   After the SSP restoration, all other stuffs had completed very smoothly without any more issues. I did few modifications to sites for change of server name and finally, the new environment was ready.

  Read the article

• Can not print after upgrading from 12.x to 14.04

  - by user318889

  After upgrading from V12.04 to V14.04 I am not able to print. I am using an HP LaserJet 400 M451dn. The printer troubleshooter told me that there is no solution to the problem. This is the output of the advanced diagnositc output. (Due to limited space I cut the output!) Can anybody tell me what is going wrong. I am using the printer via USB ? Page 1 (Scheduler not running?): {'cups_connection_failure': False} Page 2 (Is local server publishing?): {'local_server_exporting_printers': False} Page 3 (Choose printer): {'cups_dest': , 'cups_instance': None, 'cups_queue': u'HP-LaserJet-400-color-M451dn', 'cups_queue_listed': True} Page 4 (Check printer sanity): {'cups_device_uri_scheme': u'hp', 'cups_printer_dict': {'device-uri': u'hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670', 'printer-info': u'Hewlett-Packard HP LaserJet 400 color M451dn', 'printer-is-shared': True, 'printer-location': u'Pinatubo', 'printer-make-and-model': u'HP LJ 300-400 color M351-M451 Postscript (recommended)', 'printer-state': 4, 'printer-state-message': u'', 'printer-state-reasons': [u'none'], 'printer-type': 8556636, 'printer-uri-supported': u'ipp://localhost:631/printers/HP-LaserJet-400-color-M451dn'}, 'cups_printer_remote': False, 'hplip_output': (['', '\x1b[01mHP Linux Imaging and Printing System (ver. 3.14.6)\x1b[0m', '\x1b[01mDevice Information Utility ver. 5.2\x1b[0m', '', 'Copyright (c) 2001-13 Hewlett-Packard Development Company, LP', 'This software comes with ABSOLUTELY NO WARRANTY.', 'This is free software, and you are welcome to distribute it', 'under certain conditions. See COPYING file for more details.', '', '', '\x1b[01mhp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670\x1b[0m', '', '\x1b[01mDevice Parameters (dynamic data):\x1b[0m', '\x1b[01m Parameter Value(s) \x1b[0m', ' ---------------------------- ----------------------------------------------------------', ' back-end hp ', " cups-printers ['HP-LaserJet-400-color-M451dn'] ", ' cups-uri hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670 ', ' dev-file ', ' device-state -1 ', ' device-uri hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670 ', ' deviceid ', ' error-state 101 ', ' host ', ' is-hp True ', ' panel 0 ', ' panel-line1 ', ' panel-line2 ', ' port 1 ', ' serial CNFF308670 ', ' status-code 5002 ', ' status-desc ', '\x1b[01m', 'Model Parameters (static data):\x1b[0m', '\x1b[01m Parameter Value(s) \x1b[0m', ' ---------------------------- ----------------------------------------------------------', ' align-type 0 ', ' clean-type 0 ', ' color-cal-type 0 ', ' copy-type 0 ', ' embedded-server-type 0 ', ' fax-type 0 ', ' fw-download False ', ' icon hp_color_laserjet_cp2025.png ', ' io-mfp-mode 1 ', ' io-mode 1 ', ' io-support 6 ', ' job-storage 0 ', ' linefeed-cal-type 0 ', ' model HP_LaserJet_400_color_M451dn ', ' model-ui HP LaserJet 400 Color m451dn ', ' model1 HP LaserJet 400 Color M451dn ', ' monitor-type 0 ', ' panel-check-type 0 ', ' pcard-type 0 ', ' plugin 0 ', ' plugin-reason 0 ', ' power-settings 0 ', ' ppd-name lj_300_400_color_m351_m451 ', ' pq-diag-type 0 ', ' r-type 0 ', ' r0-agent1-kind 4 ', ' r0-agent1-sku CE410A/CE410X ', ' r0-agent1-type 1 ', ' r0-agent2-kind 4 ', ' r0-agent2-sku CE411A ', ' r0-agent2-type 4 ', ' r0-agent3-kind 4 ', ' r0-agent3-sku CE413A ', ' r0-agent3-type 5 ', ' r0-agent4-kind 4 ', ' r0-agent4-sku CE412A ', ' r0-agent4-type 6 ', ' scan-src 0 ', ' scan-type 0 ', ' status-battery-check 0 ', ' status-dynamic-counters 0 ', ' status-type 3 ', ' support-released True ', ' support-subtype 2202411 ', ' support-type 2 ', ' support-ver 3.12.2 ', " tech-class ['Postscript'] ", " tech-subclass ['Normal'] ", ' tech-type 4 ', ' usb-pid 3882 ', ' usb-vid 1008 ', ' wifi-config 0 ', '\x1b[01m', 'Status History (most recent first):\x1b[0m', '\x1b[01m Date/Time Code Status Description User Job ID \x1b[0m', ' -------------------- ----- ---------------------------------------- -------- --------', ' 08/21/14 00:07:25 5012 Device communication error richard 0 ', ' 08/20/14 13:42:44 500 Started a print job richard 4214 ', '', '', 'Done.', ''], ['\x1b[35;01mwarning: No display found.\x1b[0m', '\x1b[31;01merror: hp-info -u/--gui requires Qt4 GUI support. Entering interactive mode.\x1b[0m', '\x1b[31;01merror: Unable to communicate with device (code=12): hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670\x1b[0m', '\x1b[31;01merror: Error opening device (Device not found).\x1b[0m', ''], 0), 'is_cups_class': False, 'local_cups_queue_attributes': {'charset-configured': u'utf-8', 'charset-supported': [u'us-ascii', u'utf-8'], 'color-supported': True, 'compression-supported': [u'none', u'gzip'], 'copies-default': 1, 'copies-supported': (1, 9999), 'cups-version': u'1.7.2', 'device-uri': u'hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670', 'document-format-default': u'application/octet-stream', 'document-format-supported': [u'application/octet-stream', u'application/pdf', u'application/postscript', u'application/vnd.adobe-reader-postscript', u'application/vnd.cups-command', u'application/vnd.cups-pdf', u'application/vnd.cups-pdf-banner', u'application/vnd.cups-postscript', u'application/vnd.cups-raw', u'application/vnd.samsung-ps', u'application/x-cshell', u'application/x-csource', u'application/x-perl', u'application/x-shell', u'image/gif', u'image/jpeg', u'image/png', u'image/tiff', u'image/urf', u'image/x-bitmap', u'image/x-photocd', u'image/x-portable-anymap', u'image/x-portable-bitmap', u'image/x-portable-graymap', u'image/x-portable-pixmap', u'image/x-sgi-rgb', u'image/x-sun-raster', u'image/x-xbitmap', u'image/x-xpixmap', u'image/x-xwindowdump', u'text/css', u'text/html', u'text/plain'], 'finishings-default': 3, 'finishings-supported': [3], 'generated-natural-language-supported': [u'en-us'], 'ipp-versions-supported': [u'1.0', u'1.1', u'2.0', u'2.1'], 'ippget-event-life': 15, 'job-creation-attributes-supported': [u'copies', u'finishings', u'ipp-attribute-fidelity', u'job-hold-until', u'job-name', u'job-priority', u'job-sheets', u'media', u'media-col', u'multiple-document-handling', u'number-up', u'output-bin', u'orientation-requested', u'page-ranges', u'print-color-mode', u'print-quality', u'printer-resolution', u'sides'], 'job-hold-until-default': u'no-hold', 'job-hold-until-supported': [u'no-hold', u'indefinite', u'day-time', u'evening', u'night', u'second-shift', u'third-shift', u'weekend'], 'job-ids-supported': True, 'job-k-limit': 0, 'job-k-octets-supported': (0, 470914416), 'job-page-limit': 0, 'job-priority-default': 50, 'job-priority-supported': [100], 'job-quota-period': 0, 'job-settable-attributes-supported': [u'copies', u'finishings', u'job-hold-until', u'job-name', u'job-priority', u'media', u'media-col', u'multiple-document-handling', u'number-up', u'output-bin', u'orientation-requested', u'page-ranges', u'print-color-mode', u'print-quality', u'printer-resolution', u'sides'], 'job-sheets-default': (u'none', u'none'), 'job-sheets-supported': [u'none', u'classified', u'confidential', u'form', u'secret', u'standard', u'topsecret', u'unclassified'], 'jpeg-k-octets-supported': (0, 470914416), 'jpeg-x-dimension-supported': (0, 65535), 'jpeg-y-dimension-supported': (1, 65535), 'marker-change-time': 0, 'media-bottom-margin-supported': [423], 'media-col-default': u'(unknown IPP value tag 0x34)', 'media-col-supported': [u'media-bottom-margin', u'media-left-margin', u'media-right-margin', u'media-size', u'media-source', u'media-top-margin', u'media-type'], 'media-default': u'iso_a4_210x297mm', 'media-left-margin-supported': [423], 'media-right-margin-supported': [423],

  Read the article

• Five development tools I can't live without

  - by bconlon

  When applying to join Geeks with Blogs I had to specify the development tools I use every day. That got me thinking, it's taken a long time to whittle my tools of choice down to the selection I use, so it might be worth sharing. Before I begin, I appreciate we all have our preferred development tools, but these are the ones that work for me. Microsoft Visual Studio Microsoft Visual Studio has been my development tool of choice for more years than I care to remember. I first used this when it was Visual C++ 1.5 (hats off to those who started on 1.0) and by 2.2 it had everything I needed from a C++ IDE. Versions 4 and 5 followed and if I had to guess I would expect more Windows applications are written in VC++ 6 and VB6 than any other language. Then came the not so great versions Visual Studio .Net 2002 (7.0) and 2003 (7.1). If I'm honest I was still using v6. 2005 was better and 2008 was simply brilliant. Everything worked, the compiler was super fast and I was happy again...then came 2010...oh dear. 2010 is a big step backwards for me. It's not encouraging for my upcoming WPF exploits that 2010 is fronted in WPF technology, with the forever growing Find/Replace dialog, the issues with C++ intellisense, and the buggy debugger. That said it is still my tool of choice but I hope they sort the issue in SP1. I've tried other IDEs like Visual Age and Eclipse, but for me Visual Studio is the best. A really great tool. Liquid XML Studio XML development is a tricky business. The W3C standards are often difficult to get to the bottom of so it's great to have a graphical tool to help. I first used Liquid Technologies 5 or 6 years back when I needed to process XML data in C++. Their excellent XML Data Binding tool has an easy to use Wizard UI (as compared to Castor or JAXB command line tools) and allows you to generate code from an XML Schema. So instead of having to deal with untyped nodes like with a DOM parser, instead you get an Object Model providing a custom API in C++, C#, VB etc. More recently they developed a graphical XML IDE with XML Editor, XSLT, XQuery debugger and other XML tools. So now I can develop an XML Schema graphically, click a button to generate a Sample XML document, and click another button to run the Wizard to generate code including a Sample Application that will then load my Sample XML document into the generated object model. This is a very cool toolset. Note: XML Data Binding is nothing to do with WPF Data Binding, but I hope to cover both in more detail another time. .Net Reflector Note: I've just noticed that starting form the end of February 2011 this will no longer be a free tool !! .Net Reflector turns .Net byte code back into C# source code. But how can it work this magic? Well the clue is in the name, it uses reflection to inspect a compiled .Net assembly. The assembly is compiled to byte code, it doesn't get compiled to native machine code until its needed using a just-in-time (JIT) compiler. The byte code still has all of the information needed to see classes, variables. methods and properties, so reflector gathers this information and puts it in a handy tree. I have used .Net Reflector for years in order to understand what the .Net Framework is doing as it sometimes has undocumented, quirky features. This really has been invaluable in certain instances and I cannot praise enough kudos on the original developer Lutz Roeder. Smart Assembly In order to stop nosy geeks looking at our code using a tool like .Net Reflector, we need to obfuscate (mess up) the byte code. Smart Assembly is a tool that does this. Again I have used this for a long time. It is very quick and easy to use. Another excellent tool. Coincidentally, .Net Reflector and Smart Assembly are now both owned by Red Gate. Again kudos goes to the original developer Jean-Sebastien Lange. TortoiseSVN SVN (Apache Subversion) is a Source Control System developed as an open source project. TortoiseSVN is a graphical UI wrapper over SVN that hooks into Windows Explorer to enable files to be Updated, Committed, Merged etc. from the right click menu. This is an essential tool for keeping my hard work safe! Many years ago I used Microsoft Source Safe and I disliked CVS type systems. But TortoiseSVN is simply the best source control tool I have ever used. --- So there you have it, my top 5 development tools that I use (nearly) every day and have helped to make my working life a little easier. I'm sure there are other great tools that I wish I used but have never heard of, but if you have not used any of the above, I would suggest you check them out as they are all very, very cool products. #

  Read the article

• Solaris 11.2: Functional Deprecation

  - by alanc

  In Solaris 11.1, I updated the system headers to enable use of several attributes on functions, including noreturn and printf format, to give compilers and static analyzers more information about how they are used to give better warnings when building code. In Solaris 11.2, I've gone back in and added one more attribute to a number of functions in the system headers: __attribute__((__deprecated__)). This is used to warn people building software that they’re using function calls we recommend no longer be used. While in many cases the Solaris Binary Compatibility Guarantee means we won't ever remove these functions from the system libraries, we still want to discourage their use. I made passes through both the POSIX and C standards, and some of the Solaris architecture review cases to come up with an initial list which the Solaris architecture review committee accepted to start with. This set is by no means a complete list of Obsolete function interfaces, but should be a reasonable start at functions that are well documented as deprecated and seem useful to warn developers away from. More functions may be flagged in the future as they get deprecated, or if further passes are made through our existing deprecated functions to flag more of them. Header Interface Deprecated by Alternative Documented in <door.h> door_cred(3C) PSARC/2002/188 door_ucred(3C) door_cred(3C) <kvm.h> kvm_read(3KVM), kvm_write(3KVM) PSARC/1995/186 Functions on kvm_kread(3KVM) man page kvm_read(3KVM) <stdio.h> gets(3C) ISO C99 TC3 (Removed in ISO C11), POSIX:2008/XPG7/Unix08 fgets(3C) gets(3C) man page, and just about every gets(3C) reference online from the past 25 years, since the Morris worm proved bad things happen when it’s used. <unistd.h> vfork(2) PSARC/2004/760, POSIX:2001/XPG6/Unix03 (Removed in POSIX:2008/XPG7/Unix08) posix_spawn(3C) vfork(2) man page. <utmp.h> All functions from getutent(3C) man page PSARC/1999/103 utmpx functions from getutentx(3C) man page getutent(3C) man page <varargs.h> varargs.h version of va_list typedef ANSI/ISO C89 standard <stdarg.h> varargs(3EXT) <volmgt.h> All functions PSARC/2005/672 hal(5) API volmgt_check(3VOLMGT), etc. <sys/nvpair.h> nvlist_add_boolean(3NVPAIR), nvlist_lookup_boolean(3NVPAIR) PSARC/2003/587 nvlist_add_boolean_value, nvlist_lookup_boolean_value nvlist_add_boolean(3NVPAIR) & (9F), nvlist_lookup_boolean(3NVPAIR) & (9F). <sys/processor.h> gethomelgroup(3C) PSARC/2003/034 lgrp_home(3LGRP) gethomelgroup(3C) <sys/stat_impl.h> _fxstat, _xstat, _lxstat, _xmknod PSARC/2009/657 stat(2) old functions are undocumented remains of SVR3/COFF compatibility support If the above table is cut off when viewing in the blog, try viewing this standalone copy of the table. To See or Not To See To see these warnings, you will need to be building with either gcc (versions 3.4, 4.5, 4.7, & 4.8 are available in the 11.2 package repo), or with Oracle Solaris Studio 12.4 or later (which like Solaris 11.2, is currently in beta testing). For instance, take this oversimplified (and obviously buggy) implementation of the cat command: #include <stdio.h> int main(int argc, char **argv) { char buf[80]; while (gets(buf) != NULL) puts(buf); return 0; } Compiling it with the Studio 12.4 beta compiler will produce warnings such as: % cc -V cc: Sun C 5.13 SunOS_i386 Beta 2014/03/11 % cc gets_test.c "gets_test.c", line 6: warning: "gets" is deprecated, declared in : "/usr/include/iso/stdio_iso.h", line 221 The exact warning given varies by compilers, and the compilers also have a variety of flags to either raise the warnings to errors, or silence them. Of couse, the exact form of the output is Not An Interface that can be relied on for automated parsing, just shown for example. gets(3C) is actually a special case — as noted above, it is no longer part of the C Standard Library in the C11 standard, so when compiling in C11 mode (i.e. when __STDC_VERSION__ >= 201112L), the <stdio.h> header will not provide a prototype for it, causing the compiler to complain it is unknown: % gcc -std=c11 gets_test.c gets_test.c: In function ‘main’: gets_test.c:6:5: warning: implicit declaration of function ‘gets’ [-Wimplicit-function-declaration] while (gets(buf) != NULL) ^ The gets(3C) function of course is still in libc, so if you ignore the error or provide your own prototype, you can still build code that calls it, you just have to acknowledge you’re taking on the risk of doing so yourself. Solaris Studio 12.4 Beta % cc gets_test.c "gets_test.c", line 6: warning: "gets" is deprecated, declared in : "/usr/include/iso/stdio_iso.h", line 221 % cc -errwarn=E_DEPRECATED_ATT gets_test.c "gets_test.c", line 6: "gets" is deprecated, declared in : "/usr/include/iso/stdio_iso.h", line 221 cc: acomp failed for gets_test.c This warning is silenced in the 12.4 beta by cc -erroff=E_DEPRECATED_ATT No warning is currently issued by Studio 12.3 & earler releases. gcc 3.4.3 % /usr/sfw/bin/gcc gets_test.c gets_test.c: In function `main': gets_test.c:6: warning: `gets' is deprecated (declared at /usr/include/iso/stdio_iso.h:221) Warning is completely silenced with gcc -Wno-deprecated-declarations gcc 4.7.3 % /usr/gcc/4.7/bin/gcc gets_test.c gets_test.c: In function ‘main’: gets_test.c:6:5: warning: ‘gets’ is deprecated (declared at /usr/include/iso/stdio_iso.h:221) [-Wdeprecated-declarations] % /usr/gcc/4.7/bin/gcc -Werror=deprecated-declarations gets_test.c gets_test.c: In function ‘main’: gets_test.c:6:5: error: ‘gets’ is deprecated (declared at /usr/include/iso/stdio_iso.h:221) [-Werror=deprecated-declarations] cc1: some warnings being treated as errors Warning is completely silenced with gcc -Wno-deprecated-declarations gcc 4.8.2 % /usr/bin/gcc gets_test.c gets_test.c: In function ‘main’: gets_test.c:6:5: warning: ‘gets’ is deprecated (declared at /usr/include/iso/stdio_iso.h:221) [-Wdeprecated-declarations] while (gets(buf) != NULL) ^ % /usr/bin/gcc -Werror=deprecated-declarations gets_test.c gets_test.c: In function ‘main’: gets_test.c:6:5: error: ‘gets’ is deprecated (declared at /usr/include/iso/stdio_iso.h:221) [-Werror=deprecated-declarations] while (gets(buf) != NULL) ^ cc1: some warnings being treated as errors Warning is completely silenced with gcc -Wno-deprecated-declarations

  Read the article

• How to handle updated configuration when it's already been cloned for editing

  - by alexrussell

  Really sorry about the title that probably doesn't make much sense. Hopefully I can explain myself better here as it's something that's kinda bugged me for ages, and is now becoming a pressing concern as I write a bit of software with configuration. Most software comes with default configuration options stored in the app itself, and then there's a configuration file (let's say) that a user can edit. Once created/edited for the first time, subsequent updates to the application can not (easily) modify this configuration file for fear of clobbering the user's own changes to the default configuration. So my question is, if my application adds a new configurable parameter, what's the best way to aid discoverability of the setting and allow the user (developer) to override it as nicely as possible given the following constraints: I actually don't have a canonical default config in the application per se, it's more of a 'cascading filesystem'-like affair - the config template is stored in default/config.json and when the user wishes to edit the configuration, it's copied to user/config.json. If a user config is found it is used - there is no automatic overriding of a subset of keys, the whole new file is used and that's that. If there's no user config the default config is used. When a user wishes to edit the config they run a command to 'generate' it for them (which simply copies the config.json file from the default to the user directory). There is no UI for the configuration options as it's not appropriate to the userbase (think of my software as a library or something, the users are developers, the config is done in the user/config.json file). Due to my software being library-like there's no simple way to, on updating of the software, run some tasks automatically (so any ideas of look at the current config, compare to template config, add ing missing keys) aren't appropriate. The only solution I can think of right now is to say "there's a new config setting X" in release notes, but this doesn't seem ideal to me. If you want any more information let me know. The above specifics are not actually 100% true to my situation, but they represent the problem equally well with lower complexity. If you do want specifics, however, I can explain the exact setup. Further clarification of the type of configuration I mean: think of the Atom code editor. There appears to be a default 'template' config file somewhere, but as soon as a configuration option is edited ~/.atom/config.cson is generated and the setting goes in there. From now on is Atom is updated and gets a new configuration key, this file cannot be overwritten by Atom without a lot of effort to ensure that the addition/modification of the key does not clobber. In Atom's case, because there is a GUI for editing settings, they can get away with just adding the UI for the new setting into the UI to aid 'discoverability' of the new setting. I don't have that luxury. Clarification of my constraints and what I'm actually looking for: The software I'm writing is actually a package for a larger system. This larger system is what provides the configuration, and the way it works is kinda fixed - I just do a config('some.key') kinda call and it knows to look to see if the user has a config clone and if so use it, otherwise use the default config which is part of my package. Now, while I could make my application edit the user's configuration files (there is a convention about where they're stored), it's generally not done, so I'd like to live with the constraints of the system I'm using if possible. And it's not just about discoverability either, one large concern is that the addition of a configuration key won't actually work as soon as the user has their own copy of the original template. Adding the key to the template won't make a difference as that file is never read. As such, I think this is actually quite a big flaw in the design of the configuration cascading system and thus needs to be taken up with my upstream. So, thinking about it, based on my constraints, I don't think there's going to be a good solution save for either editing the user's configuration or using a new config file every time there are updates to the default configuration. Even the release notes idea from above isn't doable as, if the user does not follow the advice, suddenly I have a config key with no value (user-defined or default). So the new question is this: what is the general way to solve the problem of having a default configuration in template config files and allowing a user to make user-specific version of these in order to override the defaults? A per-key cascade (rather than per-file cascade) where the user only specifies their overrides? In this case, what happens if a configuration value is an array - do we replace or append to the default (or, more realistically, how does the user specify whether they wish to replace or append to)? It seems like configuration is kinda hard, so how is it solved in the wild?

  Read the article

• Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to get it to work?

  - by zewone

  I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686  Any help much appreciated... Thanks, Philippe 31-10-2012 ... I have some more updates. When I do the following command it does see my Wifi router... So even if it is still disabled... the card seems to work and see the router (ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E") See below: sudo iwlist wlan1 scanning wlan1 Scan completed : Cell 01 - Address: 00:19:70:8F:B0:EA Channel:10 Frequency:2.457 GHz (Channel 10) Quality=51/70 Signal level=-59 dBm Encryption key:on ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000025dbf2188 Extra: Last beacon: 108ms ago IE: Unknown: 002035373931424332362D434539432D313144312D393742462D3030303046383145 IE: Unknown: 010882848B960C121824 IE: Unknown: 03010A IE: Unknown: 0706424520010D14 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101030003A4000027A4000042435E0062322F00 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000

  Read the article

• Developing Schema Compare for Oracle (Part 5): Query Snapshots

  - by Simon Cooper

  If you've emailed us about a bug you've encountered with the EAP or beta versions of Schema Compare for Oracle, we probably asked you to send us a query snapshot of your databases. Here, I explain what a query snapshot is, and how it helps us fix your bug. Problem 1: Debugging users' bug reports When we started the Schema Compare project, we knew we were going to get problems with users' databases - configurations we hadn't considered, features that weren't installed, unicode issues, wierd dependencies... With SQL Compare, users are generally happy to send us a database backup that we can restore using a single RESTORE DATABASE command on our test servers and immediately reproduce the problem. Oracle, on the other hand, would be a lot more tricky. As Oracle generally has a 1-to-1 mapping between instances and databases, any databases users sent would have to be restored to their own instance. Furthermore, the number of steps required to get a properly working database, and the size of most oracle databases, made it infeasible to ask every customer who came across a bug during our beta program to send us their databases. We also knew that there would be lots of issues with data security that would make it hard to get backups. So we needed an easier way to be able to debug customers issues and sort out what strange schema data Oracle was returning. Problem 2: Test execution time Another issue we knew we would have to solve was the execution time of the tests we would produce for the Schema Compare engine. Our initial prototype showed that querying the data dictionary for schema information was going to be slow (at least 15 seconds per database), and this is generally proportional to the size of the database. If you're running thousands of tests on the same databases, each one registering separate schemas, not only would the tests would take hours and hours to run, but the test servers would be hammered senseless. The solution To solve these, we needed to be able to populate the schema of a database without actually connecting to it. Well, the IDataReader interface is the primary way we read data from an Oracle server. The data dictionary queries we use return their data in terms of simple strings and numbers, which we then process and reconstruct into an object model, and the results of these queries are identical for identical schemas. So, we can record the raw results of the queries once, and then replay these results to construct the same object model as many times as required without needing to actually connect to the original database. This is what query snapshots do. They are binary files containing the raw unprocessed data we get back from the oracle server for all the queries we run on the data dictionary to get schema information. The core of the query snapshot generation takes the results of the IDataReader we get from running queries on Oracle, and passes the row data to a BinaryWriter that writes it straight to a file. The query snapshot can then be replayed to create the same object model; when the results of a specific query is needed by the population code, we can simply read the binary data stored in the file on disk and present it through an IDataReader wrapper. This is far faster than querying the server over the network, and allows us to run tests in a reasonable time. They also allow us to easily debug a customers problem; using a simple snapshot generation program, users can generate a query snapshot that could be sent along with a bug report that we can immediately replay on our machines to let us debug the issue, rather than having to obtain database backups and restore databases to test systems. There are also far fewer problems with data security; query snapshots only contain schema information, which is generally less sensitive than table data. Query snapshots implementation However, actually implementing such a feature did have a couple of 'gotchas' to it. My second blog post detailed the development of the dependencies algorithm we use to ensure we get all the dependencies in the database, and that algorithm uses data from both databases to find all the needed objects - what database you're comparing to affects what objects get populated from both databases. We get information on these additional objects using an appropriate WHERE clause on all the population queries. So, in order to accurately replay the results of querying the live database, the query snapshot needs to be a snapshot of a comparison of two databases, not just populating a single database. Furthermore, although the code population queries (eg querying all_tab_cols to get column information) can simply be passed straight from the IDataReader to the BinaryWriter, we need to hook into and run the live dependencies algorithm while we're creating the snapshot to ensure we get the same WHERE clauses, and the same query results, as if we were populating straight from a live system. We also need to store the results of the dependencies queries themselves, as the resulting dependency graph is stored within the OracleDatabase object that is produced, and is later used to help order actions in synchronization scripts. This is significantly helped by the dependencies algorithm being a deterministic algorithm - given the same input, it will always return the same output. Therefore, when we're replaying a query snapshot, and processing dependency information, we simply have to return the results of the queries in the order we got them from the live database, rather than trying to calculate the contents of all_dependencies on the fly. Query snapshots are a significant feature in Schema Compare that really helps us to debug problems with the tool, as well as making our testers happier. Although not really user-visible, they are very useful to the development team to help us fix bugs in the product much faster than we otherwise would be able to.

  Read the article

• Jersey 2 in GlassFish 4 - First Java EE 7 Implementation Now Integrated (TOTD #182)

  - by arungupta

  The JAX-RS 2.0 specification released their Early Draft 3 recently. One of my earlier blogs explained as the features were first introduced in the very first draft of the JAX-RS 2.0 specification. Last week was another milestone when the first Java EE 7 specification implementation was added to GlassFish 4 builds. Jakub blogged about Jersey 2 integration in GlassFish 4 builds. Most of the basic functionality is working but EJB, CDI, and Validation are still a TBD. Here is a simple Tip Of The Day (TOTD) sample to get you started with using that functionality. Create a Java EE 6-style Maven project mvn archetype:generate -DarchetypeGroupId=org.codehaus.mojo.archetypes -DarchetypeArtifactId=webapp-javaee6 -DgroupId=example -DartifactId=jersey2-helloworld -DarchetypeVersion=1.5 -DinteractiveMode=false Note, this is still a Java EE 6 archetype, at least for now. Open the project in NetBeans IDE as it makes it much easier to edit/add the files. Add the following <respositories> <repositories> <repository> <id>snapshot-repository.java.net</id> <name>Java.net Snapshot Repository for Maven</name> <url>https://maven.java.net/content/repositories/snapshots/</url> <layout>default</layout> </repository></repositories> Add the following <dependency>s <dependency> <groupId>junit</groupId> <artifactId>junit</artifactId> <version>4.10</version> <scope>test</scope></dependency><dependency> <groupId>javax.ws.rs</groupId> <artifactId>javax.ws.rs-api</artifactId> <version>2.0-m09</version> <scope>test</scope></dependency><dependency> <groupId>org.glassfish.jersey.core</groupId> <artifactId>jersey-client</artifactId> <version>2.0-m05</version> <scope>test</scope></dependency> The complete list of Maven coordinates for Jersey2 are available here. An up-to-date status of Jersey 2 can always be obtained from here. Here is a simple resource class: @Path("movies")public class MoviesResource { @GET @Path("list") public List<Movie> getMovies() { List<Movie> movies = new ArrayList<Movie>(); movies.add(new Movie("Million Dollar Baby", "Hillary Swank")); movies.add(new Movie("Toy Story", "Buzz Light Year")); movies.add(new Movie("Hunger Games", "Jennifer Lawrence")); return movies; }} This resource publishes a list of movies and is accessible at "movies/list" path with HTTP GET. The project is using the standard JAX-RS APIs. Of course, you need the trivial "Movie" and the "Application" class as well. They are available in the downloadable project anyway. Build the project mvn package And deploy to GlassFish 4.0 promoted build 43 (download, unzip, and start as "bin/asadmin start-domain") as asadmin deploy --force=true target/jersey2-helloworld.war Add a simple test case by right-clicking on the MoviesResource class, select "Tools", "Create Tests", and take defaults. Replace the function "testGetMovies" to @Testpublic void testGetMovies() { System.out.println("getMovies"); Client client = ClientFactory.newClient(); List<Movie> movieList = client.target("http://localhost:8080/jersey2-helloworld/webresources/movies/list") .request() .get(new GenericType<List<Movie>>() {}); assertEquals(3, movieList.size());} This test uses the newly defined JAX-RS 2 client APIs to access the RESTful resource. Run the test by giving the command "mvn test" and see the output as ------------------------------------------------------- T E S T S-------------------------------------------------------Running example.MoviesResourceTestgetMoviesTests run: 1, Failures: 0, Errors: 0, Skipped: 0, Time elapsed: 0.561 secResults :Tests run: 1, Failures: 0, Errors: 0, Skipped: 0 GlassFish 4 contains Jersey 2 as the JAX-RS implementation. If you want to use Jersey 1.1 functionality, then Martin's blog provide more details on that. All JAX-RS 1.x functionality will be supported using standard APIs anyway. This workaround is only required if Jersey 1.x functionality needs to be accessed. The complete source code explained in this project can be downloaded from here. Here are some pointers to follow JAX-RS 2 Specification Early Draft 3 Latest status on specification (jax-rs-spec.java.net) Latest JAX-RS 2.0 Javadocs Latest status on Jersey (Reference Implementation of JAX-RS 2 - jersey.java.net) Latest Jersey API Javadocs Latest GlassFish 4.0 Promoted Build Follow @gf_jersey Provide feedback on Jersey 2 to [email protected] and JAX-RS specification to [email protected].

  Read the article

• MERGE gives better OUTPUT options

  - by Rob Farley

  MERGE is very cool. There are a ton of useful things about it – mostly around the fact that you can implement a ton of change against a table all at once. This is great for data warehousing, handling changes made to relational databases by applications, all kinds of things. One of the more subtle things about MERGE is the power of the OUTPUT clause. Useful for logging.   If you’re not familiar with the OUTPUT clause, you really should be – it basically makes your DML (INSERT/DELETE/UPDATE/MERGE) statement return data back to you. This is a great way of returning identity values from INSERT commands (so much better than SCOPE_IDENTITY() or the older (and worse) @@IDENTITY, because you can get lots of rows back). You can even use it to grab default values that are set using non-deterministic functions like NEWID() – things you couldn’t normally get back without running another query (or with a trigger, I guess, but that’s not pretty). That inserted table I referenced – that’s part of the ‘behind-the-scenes’ work that goes on with all DML changes. When you insert data, this internal table called inserted gets populated with rows, and then used to inflict the appropriate inserts on the various structures that store data (HoBTs – the Heaps or B-Trees used to store data as tables and indexes). When deleting, the deleted table gets populated. Updates get a matching row in both tables (although this doesn’t mean that an update is a delete followed by an inserted, it’s just the way it’s handled with these tables). These tables can be referenced by the OUTPUT clause, which can show you the before and after for any DML statement. Useful stuff. MERGE is slightly different though. With MERGE, you get a mix of entries. Your MERGE statement might be doing some INSERTs, some UPDATEs and some DELETEs. One of the most common examples of MERGE is to perform an UPSERT command, where data is updated if it already exists, or inserted if it’s new. And in a single operation too. Here, you can see the usefulness of the deleted and inserted tables, which clearly reflect the type of operation (but then again, MERGE lets you use an extra column called $action to show this). (Don’t worry about the fact that I turned on IDENTITY_INSERT, that’s just so that I could insert the values) One of the things I love about MERGE is that it feels almost cursor-like – the UPDATE bit feels like “WHERE CURRENT OF …”, and the INSERT bit feels like a single-row insert. And it is – but into the inserted and deleted tables. The operations to maintain the HoBTs are still done using the whole set of changes, which is very cool. And $action – very convenient. But as cool as $action is, that’s not the point of my post. If it were, I hope you’d all be disappointed, as you can’t really go near the MERGE statement without learning about it. The subtle thing that I love about MERGE with OUTPUT is that you can hook into more than just inserted and deleted. Did you notice in my earlier query that my source table had a ‘src’ field, that wasn’t used in the insert? Normally, this would be somewhat pointless to include in my source query. But with MERGE, I can put that in the OUTPUT clause. This is useful stuff, particularly when you’re needing to audit the changes. Suppose your query involved consolidating data from a number of sources, but you didn’t need to insert that into the actual table, just into a table for audit. This is now very doable, either using the INTO clause of OUTPUT, or surrounding the whole MERGE statement in brackets (parentheses if you’re American) and using a regular INSERT statement. This is also doable if you’re using MERGE to just do INSERTs. In case you hadn’t realised, you can use MERGE in place of an INSERT statement. It’s just like the UPSERT-style statement we’ve just seen, except that we want nothing to match. That’s easy to do, we just use ON 1=2. This is obviously more convoluted than a straight INSERT. And it’s slightly more effort for the database engine too. But, if you want the extra audit capabilities, the ability to hook into the other source columns is definitely useful. Oh, and before people ask if you can also hook into the target table’s columns... Yes, of course. That’s what deleted and inserted give you.

  Read the article

• Best Practices Generating WebService Proxies for Oracle Sales Cloud (Fusion CRM)

  - by asantaga

  I've recently been building a REST Service wrapper for Oracle Sales Cloud and initially all was going well, however as soon as I added all of my Web Service proxies I started to get weird errors..  My project structure looks like this What I found out was if I only had the InteractionsService & OpportunityService WebService Proxies then all worked ok, but as soon as I added the LocationsService Proxy, I would start to see strange JAXB errors. Example of the error message Exception in thread "main" javax.xml.ws.WebServiceException: Unable to create JAXBContextat com.sun.xml.ws.model.AbstractSEIModelImpl.createJAXBContext(AbstractSEIModelImpl.java:164)at com.sun.xml.ws.model.AbstractSEIModelImpl.postProcess(AbstractSEIModelImpl.java:94)at com.sun.xml.ws.model.RuntimeModeler.buildRuntimeModel(RuntimeModeler.java:281)at com.sun.xml.ws.client.WSServiceDelegate.buildRuntimeModel(WSServiceDelegate.java:762)at weblogic.wsee.jaxws.spi.WLSProvider$ServiceDelegate.buildRuntimeModel(WLSProvider.java:982)at com.sun.xml.ws.client.WSServiceDelegate.createSEIPortInfo(WSServiceDelegate.java:746)at com.sun.xml.ws.client.WSServiceDelegate.addSEI(WSServiceDelegate.java:737)at com.sun.xml.ws.client.WSServiceDelegate.getPort(WSServiceDelegate.java:361)at weblogic.wsee.jaxws.spi.WLSProvider$ServiceDelegate.internalGetPort(WLSProvider.java:934)at weblogic.wsee.jaxws.spi.WLSProvider$ServiceDelegate$PortClientInstanceFactory.createClientInstance(WLSProvider.java:1039)...... Looking further down I see the error message is related to JAXB not being able to find an objectFactory for one of its types Caused by: java.security.PrivilegedActionException: com.sun.xml.bind.v2.runtime.IllegalAnnotationsException: 6 counts of IllegalAnnotationExceptionsThere's no ObjectFactory with an @XmlElementDecl for the element {http://xmlns.oracle.com/apps/crmCommon/activities/activitiesService/}AssigneeRsrcOrgIdthis problem is related to the following location:at protected javax.xml.bind.JAXBElement com.oracle.xmlns.apps.crmcommon.activities.activitiesservice.ActivityAssignee.assigneeRsrcOrgId at com.oracle.xmlns.apps.crmcommon.activities.activitiesservice.ActivityAssignee This is very strange... My first thoughts are that when I generated the WebService Proxy I entered the package name as "oracle.demo.pts.fusionproxy.servicename" and left the generated types as blank. This way all the generated types get put into the same package hierarchy and when deployed they get merged... Sounds resaonable and appears to work but not in this case..  To resolve this I regenerate the proxy but this time setting : Package name : To the name of my package eg. oracle.demo.pts.fusionproxy.interactionsRoot Package for Generated Types :  Package where the types will be generated to, e.g. oracle.demo.pts.fusionproxy.SalesParty.types When I ran the application now, it all works , awesome eh???? Alas no, there is a serious side effect. The problem now is that to help coding I've created a collection of helper classes , these helper classes take parameters which use some of the "generic" datatypes, like FindCriteria. e.g. This wont work any more public static FindCriteria createCustomFindCriteria(FindCriteria pFc,String pAttributes) Here lies a gremlin of a problem.. I cant use this method anymore, this is because the FindCriteria datatype is now being defined two, or more times, in the generated code for my project. If you leave the Root Package for types blank it will get generated to com.oracle.xmlns, and if you populate it then it gets generated to your custom package.. The two datatypes look the same, sound the same (and if this were a duck would sound the same), but THEY ARE NOT THE SAME... Speaking to development, they recommend you should not be entering anything in the Root Packages section, so the mystery thickens why does it work.. Well after spending sometime with some colleagues of mine in development we've identified the issue.. Alas different parts of Oracle Fusion Development have multiple schemas with the same namespace, when the WebService generator generates its classes its not seeing the other schemas properly and not generating the Object Factories correctly...  Thankfully I've found a workaround Solution Overview When generating the proxies leave the Root Package for Generated Types BLANK When you have finished generating your proxies, use the JAXB tool XJC and generate Java classes for all datatypes  Create a project within your JDeveloper11g workspace and import the java classes into this project Final bit.. within the project dependencies ensure that the JAXB/XJC generated classes are "FIRST" in the classpath Solution Details Generate the WebServices SOAP proxies When generating the proxies your generation dialog should look like this Ensure the "unwrap" parameters is selected, if it isn't then that's ok, it simply means when issuing a "get" you need to extract out the Element Generate the JAXB Classes using XJC XJC provides a command line switch called -wsdl, this (although is experimental/beta) , accepts a HTTP WSDL and will generate the relevant classes. You can put these into a single batch/shell script xjc -wsdl https://fusionservername:443/appCmmnCompInteractions/InteractionService?wsdlxjc -wsdl https://fusionservername443/opptyMgmtOpportunities/OpportunityService?wsdl Create Project in JDeveloper to store the XJC "generated" JAXB classes Within the project folder create a filesystem folder called "src" and copy the generated files into this folder. JDeveloper11g should then see the classes and display them, if it doesnt try clicking the "refresh" button In your main project ensure that the JDeveloper XJC project is selected as a dependancy and IMPORTANT make sure it is at the top of the list. This ensures that the classes are at the front of the classpath And voilà.. Hopefully you wont see any JAXB generation errors and you can use common datatypes interchangeably in your project, (e.g. FindCriteria etc)

  Read the article

• Multiple Audio Issues

  - by Lerp

  I am having issues with my audio on Ubuntu 12.04, I will try and give as much detail as possible so sorry if there's too much detail. The Problem Audio plays from both speakers and headphone regardless of what connector I choose and regardless of the profile I use. The microphone is constantly being played through headphones & speakers. The headphone audio is extremely quiet but plays from both ears when I select "Headphones" for the connector in Sound Settings. The headphone audio only plays from one ear and is quiet (but not as quiet as above) when I select "Analogue Output" for the connector in Sound Settings. I can only select "Headphones" as the connector in Sound Settings if I set the profile to either "Analogue Stereo Output/Duplex", all others only allow me to choose "Analogue Output" for the connector. Despite the headphone sound issues, the speaker sound is fine apart from the fact that I am not able to select which output is used, they just both play. My headphone and microphone are plugged into the front and my speakers are plugged into the back. What I have tried I have put everything in alsamixer to 100 apart from "Front Mic Boost" which I have set to 0. Command Output aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: AD198x Analog [AD198x Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: AD198x Digital [AD198x Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 2: AD198x Headphone [AD198x Headphone] Subdevices: 1/1 Subdevice #0: subdevice #0 arecord -l **** List of CAPTURE Hardware Devices **** card 0: Intel [HDA Intel], device 0: AD198x Analog [AD198x Analog] Subdevices: 2/3 Subdevice #0: subdevice #0 Subdevice #1: subdevice #1 Subdevice #2: subdevice #2 cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xf7ff8000 irq 70 cat /proc/asound/modules 0 snd_hda_intel cat /proc/asound/card*/codec* | grep "Codec" Codec: Analog Devices AD1989B cat /etc/modprobe.d/alsa-base.conf # autoloader aliases install sound-slot-0 /sbin/modprobe snd-card-0 install sound-slot-1 /sbin/modprobe snd-card-1 install sound-slot-2 /sbin/modprobe snd-card-2 install sound-slot-3 /sbin/modprobe snd-card-3 install sound-slot-4 /sbin/modprobe snd-card-4 install sound-slot-5 /sbin/modprobe snd-card-5 install sound-slot-6 /sbin/modprobe snd-card-6 install sound-slot-7 /sbin/modprobe snd-card-7 # Cause optional modules to be loaded above generic modules install snd /sbin/modprobe --ignore-install snd $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-ioctl32 ; /sbin/modprobe --quiet --use-blacklist snd-seq ; } # # Workaround at bug #499695 (reverted in Ubuntu see LP #319505) install snd-pcm /sbin/modprobe --ignore-install snd-pcm $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-pcm-oss ; : ; } install snd-mixer /sbin/modprobe --ignore-install snd-mixer $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-mixer-oss ; : ; } install snd-seq /sbin/modprobe --ignore-install snd-seq $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; /sbin/modprobe --quiet --use-blacklist snd-seq-oss ; : ; } # install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; : ; } # Cause optional modules to be loaded above sound card driver modules install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-emu10k1-synth ; } install snd-via82xx /sbin/modprobe --ignore-install snd-via82xx $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq ; } # Load saa7134-alsa instead of saa7134 (which gets dragged in by it anyway) install saa7134 /sbin/modprobe --ignore-install saa7134 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist saa7134-alsa ; : ; } # Prevent abnormal drivers from grabbing index 0 options bt87x index=-2 options cx88_alsa index=-2 options saa7134-alsa index=-2 options snd-atiixp-modem index=-2 options snd-intel8x0m index=-2 options snd-via82xx-modem index=-2 options snd-usb-audio index=-2 options snd-usb-caiaq index=-2 options snd-usb-ua101 index=-2 options snd-usb-us122l index=-2 options snd-usb-usx2y index=-2 # Ubuntu #62691, enable MPU for snd-cmipci options snd-cmipci mpu_port=0x330 fm_port=0x388 # Keep snd-pcsp from being loaded as first soundcard options snd-pcsp index=-2 # Keep snd-usb-audio from beeing loaded as first soundcard options snd-usb-audio index=-2 Hopefully I have provided enough information, I will happily provide anymore information needed. Thank you. Update Reinstalling alsa-base and pulseaudio fixed the headphone issues I was having.

  Read the article

• How can I set my screen resolution to match my TV?

  - by Scott Severance

  I have a computer in my classroom that's connected to an LG smart TV (that's actually not so smart. I wouldn't recommend buying one.). For the touch interface, the TV wants a resolution of 1920x1080 at 60Hz. However, I can't seem to set the computer to that resolution. The display settings only offer 1024x768 and 640x480. The computer dual boots with Windows XP, where widescreen options are available in approximately the required size, but the exact resolution -- or even aspect ratio-- isn't available in XP either. I tried the following command: xrandr -s 1920x1080 -r 60 The response was: Size 1920x1080 not found in available modes Back in the old days, the solution would be to edit xorg.conf. However, since that file no longer exists, and I haven't found up-to-date info, I don't know what else to do. If it helps, this machine will never be connected to a different display, so resolution flexibility isn't important. Here's the output of lshw: *-display:0 description: VGA compatible controller product: 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 03 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:42 memory:fe800000-febfffff memory:d0000000-dfffffff ioport:ecd8(size=8) *-display:1 UNCLAIMED description: Display controller product: 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 03 width: 64 bits clock: 33MHz According to the system settings, my graphics driver is unknown and my "experience" is standard. This is 64-bit Ubuntu 12.04 (Precise) Note: There are a number of similar questions to this one, but they didn't include any answers that helped me. Update After posting this question, I noticed one in the sidebar that I hadn't found through search but which appeared to contain the answer. Based on that question, I created the /etc/X11/xorg.conf file below: Section "ServerLayout" Identifier "X.org Configured" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "/usr/share/fonts/X11/misc" FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" FontPath "built-ins" EndSection Section "Module" Load "glx" Load "dri2" Load "dbe" Load "dri" Load "record" Load "extmod" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "LG" ModelName "Smart TV" EndSection Section "Device" ### Available Driver options are:- ### Values: <i>: integer, <f>: float, <bool>: "True"/"False", ### <string>: "String", <freq>: "<f> Hz/kHz/MHz", ### <percent>: "<f>%" ### [arg]: arg optional #Option "DRI" # [<bool>] #Option "ColorKey" # <i> #Option "VideoKey" # <i> #Option "FallbackDebug" # [<bool>] #Option "Tiling" # [<bool>] #Option "LinearFramebuffer" # [<bool>] #Option "Shadow" # [<bool>] #Option "SwapbuffersWait" # [<bool>] #Option "TripleBuffer" # [<bool>] #Option "XvMC" # [<bool>] #Option "XvPreferOverlay" # [<bool>] #Option "DebugFlushBatches" # [<bool>] #Option "DebugFlushCaches" # [<bool>] #Option "DebugWait" # [<bool>] #Option "HotPlug" # [<bool>] #Option "RelaxedFencing" # [<bool>] Identifier "Card0" Driver "intel" BusID "PCI:0:2:0" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" DefaultDepth 24 #SubSection "Display" # Viewport 0 0 # Depth 1 #EndSubSection #SubSection "Display" # Viewport 0 0 # Depth 4 #EndSubSection #SubSection "Display" # Viewport 0 0 # Depth 8 #EndSubSection #SubSection "Display" # Viewport 0 0 # Depth 15 #EndSubSection #SubSection "Display" # Viewport 0 0 # Depth 16 #EndSubSection SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" "1920x1080" EndSubSection EndSection According to /var/log/Xorg.0.log, my settings aren't being applied. In fact, I wonder if the config file is even being read. [ 1209.083] (**) intel(0): Depth 24, (--) framebuffer bpp 32 [ 1209.084] (==) intel(0): RGB weight 888 [ 1209.084] (==) intel(0): Default visual is TrueColor [ 1209.084] (II) intel(0): Integrated Graphics Chipset: Intel(R) G41 [ 1209.084] (--) intel(0): Chipset: "G41" [ 1209.084] (**) intel(0): Relaxed fencing enabled [ 1209.084] (**) intel(0): Wait on SwapBuffers? enabled [ 1209.084] (**) intel(0): Triple buffering? enabled [ 1209.084] (**) intel(0): Framebuffer tiled [ 1209.084] (**) intel(0): Pixmaps tiled [ 1209.084] (**) intel(0): 3D buffers tiled [ 1209.084] (**) intel(0): SwapBuffers wait enabled [ 1209.084] (==) intel(0): video overlay key set to 0x101fe [ 1209.172] (II) intel(0): Output VGA1 using monitor section Monitor0 [ 1209.260] (II) intel(0): EDID for output VGA1 [ 1209.260] (II) intel(0): Printing probed modes for output VGA1 [ 1209.260] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz) [ 1209.260] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz) [ 1209.260] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz) [ 1209.260] (II) intel(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz) [ 1209.260] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 489 492 525 -hsync -vsync (31.5 kHz) [ 1209.260] (II) intel(0): Output VGA1 connected [ 1209.260] (II) intel(0): Using user preference for initial modes [ 1209.260] (II) intel(0): Output VGA1 using initial mode 1024x768 [ 1209.260] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. [ 1209.260] (II) intel(0): Kernel page flipping support detected, enabling [ 1209.260] (==) intel(0): DPI set to (96, 96)

  Read the article

• Null Values And The T-SQL IN Operator

  - by Jesse

  I came across some unexpected behavior while troubleshooting a failing test the other day that took me long enough to figure out that I thought it was worth sharing here. I finally traced the failing test back to a SELECT statement in a stored procedure that was using the IN t-sql operator to exclude a certain set of values. Here’s a very simple example table to illustrate the issue: Customers CustomerId INT, NOT NULL, Primary Key CustomerName nvarchar(100) NOT NULL SalesRegionId INT NULL   The ‘SalesRegionId’ column contains a number representing the sales region that the customer belongs to. This column is nullable because new customers get created all the time but assigning them to sales regions is a process that is handled by a regional manager on a periodic basis. For the purposes of this example, the Customers table currently has the following rows: CustomerId CustomerName SalesRegionId 1 Customer A 1 2 Customer B NULL 3 Customer C 4 4 Customer D 2 5 Customer E 3   How could we write a query against this table for all customers that are NOT in sales regions 2 or 4? You might try something like this: 1: SELECT 2: CustomerId, 3: CustomerName, 4: SalesRegionId 5: FROM Customers 6: WHERE SalesRegionId NOT IN (2,4)   Will this work? In short, no; at least not in the way that you might expect. Here’s what this query will return given the example data we’re working with: CustomerId CustomerName SalesRegionId 1 Customer A 1 5 Customer E 5   I was expecting that this query would also return ‘Customer B’, since that customer has a NULL SalesRegionId. In my mind, having a customer with no sales region should be included in a set of customers that are not in sales regions 2 or 4.When I first started troubleshooting my issue I made note of the fact that this query should probably be re-written without the NOT IN clause, but I didn’t suspect that the NOT IN clause was actually the source of the issue. This particular query was only one minor piece in a much larger process that was being exercised via an automated integration test and I simply made a poor assumption that the NOT IN would work the way that I thought it should. So why doesn’t this work the way that I thought it should? From the MSDN documentation on the t-sql IN operator: If the value of test_expression is equal to any value returned by subquery or is equal to any expression from the comma-separated list, the result value is TRUE; otherwise, the result value is FALSE. Using NOT IN negates the subquery value or expression. The key phrase out of that quote is, “… is equal to any expression from the comma-separated list…”. The NULL SalesRegionId isn’t included in the NOT IN because of how NULL values are handled in equality comparisons. From the MSDN documentation on ANSI_NULLS: The SQL-92 standard requires that an equals (=) or not equal to (<>) comparison against a null value evaluates to FALSE. When SET ANSI_NULLS is ON, a SELECT statement using WHERE column_name = NULL returns zero rows even if there are null values in column_name. A SELECT statement using WHERE column_name <> NULL returns zero rows even if there are nonnull values in column_name. In fact, the MSDN documentation on the IN operator includes the following blurb about using NULL values in IN sub-queries or expressions that are used with the IN operator: Any null values returned by subquery or expression that are compared to test_expression using IN or NOT IN return UNKNOWN. Using null values in together with IN or NOT IN can produce unexpected results. If I were to include a ‘SET ANSI_NULLS OFF’ command right above my SELECT statement I would get ‘Customer B’ returned in the results, but that’s definitely not the right way to deal with this. We could re-write the query to explicitly include the NULL value in the WHERE clause: 1: SELECT 2: CustomerId, 3: CustomerName, 4: SalesRegionId 5: FROM Customers 6: WHERE (SalesRegionId NOT IN (2,4) OR SalesRegionId IS NULL)   This query works and properly includes ‘Customer B’ in the results, but I ultimately opted to re-write the query using a LEFT OUTER JOIN against a table variable containing all of the values that I wanted to exclude because, in my case, there could potentially be several hundred values to be excluded. If we were to apply the same refactoring to our simple sales region example we’d end up with: 1: DECLARE @regionsToIgnore TABLE (IgnoredRegionId INT) 2: INSERT @regionsToIgnore values (2),(4) 3:  4: SELECT 5: c.CustomerId, 6: c.CustomerName, 7: c.SalesRegionId 8: FROM Customers c 9: LEFT OUTER JOIN @regionsToIgnore r ON r.IgnoredRegionId = c.SalesRegionId 10: WHERE r.IgnoredRegionId IS NULL By performing a LEFT OUTER JOIN from Customers to the @regionsToIgnore table variable we can simply exclude any rows where the IgnoredRegionId is null, as those represent customers that DO NOT appear in the ignored regions list. This approach will likely perform better if the number of sales regions to ignore gets very large and it also will correctly include any customers that do not yet have a sales region.

  Read the article

• VS2010 crashes when opening a vsp generated using VS 2012

  - by Tarun Arora

  I recently profiled some web applications using Visual Studio 2012, a vsp (Visual Studio Profile) file was generated as a result of the profiling session. I could successfully open the vsp file in Visual Studio 2012 as expected but when I tried to open the vsp file in Visual Studio 2010 the VS2010 IDE crashed. As a responsible citizen I raised bug # 762202 on Microsoft Connect site using the Microsoft Visual Studio 2012 Feedback Client. Note – In case you didn’t already know, VSP generated in Visual Studio 2012 is not backward compatible. Please refer below for the steps to reproduce the issue and the resolution of the connect bug. 1. Behaviour and Steps to Reproduce the Issue Description I have generated a vsp file by using the Visual Studio 2012 Standalone profiler. When I try and open the vsp file in Visual Studio 2010 the IDE crashes. I understand that a vsp generated by using VS 2012 cannot be opened in VS 2010, but the IDE crashing is not the behaviour I would expect to see. Steps to Reproduce the Issue 1. Pick up the Stand lone profiler from the VS 2012 installation media. The folder has both x 64 and x86 installer, since the machine I am using is x64 bit. I have installed the x64 version of the standalone profiler. 2. I have configured the system path by setting the 'environment variable' path to where the profiler is installed. In my case this is, C:\Program Files (x86)\Microsoft Visual Studio 11.0\Team Tools\Performance Tools 3. Created a new environment variable _NT_SYMBOL_PATH and set its value to CACHE*C:\SYMBOLSCACHE;SRV*C:\SYMBOLSCACHE*HTTP://MSDL.MICROSOFT.COM/DOWNLOAD/SYMBOLS;\\FOO\BUILD1234 4. Open up CMD as an administrator and run 'VSPerfASPNETCmd /tip http://localhost:56180/ /o:C:\Temp\SampleEISK.vsp' 5. This generates the following message on the cmd       Microsoft (R) VSPerf ASP.NET Command, Version 11.0.0.0     Copyright (C) Microsoft Corporation. All rights reserved.     Configuring and attaching to ASP.NET process. Please wait.     Setting up profiling environment.     Starting monitor.     Launching ASP.NET service.     Attaching Monitor to process.     Launching Internet Explorer.     The profiler is attached to ASP.net. Please run your application scenario now.     Press Enter to stop data collection...   6. I perform certain actions and then I come back to the cmd and hit enter to shut down the profiling. Once I do this, the following message is written to the cmd, Press Enter to stop data collection... Profiling now shut down. Report file "C:\Temp\SampleEISK.vsp" was generated. Running VsPerfReport, packing symbols into the .VSP. Shutting down profiling and restarting ASP.NET. Please wait. Restarting w3wp.exe.   7. I look in the C:\Temp folder and I can see the SampleEISK.vsp file generated. I can successfully open this file in Visual Studio 2012. 8. When I am trying to open the vsp file in VS 2010 the VS 2010 IDE crashes. Kaboooom! What I would expect to happen I expect to receive a message "VS 2010 does not support the vsp file generated by VS 2012". What actually happened The VS 2010 IDE crashed 2. Resolution This is a valid bug! However, there isn’t much value in releasing a hotfix for this issue. Refer below to the resolution provided by the Visual Studio Profiler Team.  Thank you for taking the time to report this issue. We completely agree that Visual Studio 2010 should not crash. However in this particular case this is not a bug we are going to retroactively release a fix to 2010 for at this point. Given that a fix would not unblock the scenario of opening a 2012 created file on Visual Studio 2010, and there is not an active update channel for Visual Studio 2010 other than manually locating and installing hot fixes, we will not be fixing this particular issue. Best Regards, Visual Studio Profiler Team   Though it would be great to improve the behaviour however, this is not a defect that would stop you from progressing in any way. It’s important to note however that VSP files generated by Visual Studio 2012 are not backward compatible so you should refrain from opening these files in Visual Studio 2010.

  Read the article

• Documentation Changes in Solaris 11.1

  - by alanc

  One of the first places you can see Solaris 11.1 changes are in the docs, which have now been posted in the Solaris 11.1 Library on docs.oracle.com. I spent a good deal of time reviewing documentation for this release, and thought some would be interesting to blog about, but didn't review all the changes (not by a long shot), and am not going to cover all the changes here, so there's plenty left for you to discover on your own. Just comparing the Solaris 11.1 Library list of docs against the Solaris 11 list will show a lot of reorganization and refactoring of the doc set, especially in the system administration guides. Hopefully the new break down will make it easier to get straight to the sections you need when a task is at hand. Packaging System Unfortunately, the excellent in-depth guide for how to build packages for the new Image Packaging System (IPS) in Solaris 11 wasn't done in time to make the initial Solaris 11 doc set. An interim version was published shortly after release, in PDF form on the OTN IPS page. For Solaris 11.1 it was included in the doc set, as Packaging and Delivering Software With the Image Packaging System in Oracle Solaris 11.1, so should be easier to find, and easier to share links to specific pages the HTML version. Beyond just how to build a package, it includes details on how Solaris is packaged, and how package updates work, which may be useful to all system administrators who deal with Solaris 11 upgrades & installations. The Adding and Updating Oracle Solaris 11.1 Software Packages was also extended, including new sections on Relaxing Version Constraints Specified by Incorporations and Locking Packages to a Specified Version that may be of interest to those who want to keep the Solaris 11 versions of certain packages when they upgrade, such as the couple of packages that had functionality removed by an (unusual for an update release) End of Feature process in the 11.1 release. Also added in this release is a document containing the lists of all the packages in each of the major package groups in Solaris 11.1 (solaris-desktop, solaris-large-server, and solaris-small-server). While you can simply get the contents of those groups from the package repository, either via the web interface or the pkg command line, the documentation puts them in handy tables for easier side-by-side comparison, or viewing the lists before you've installed the system to pick which one you want to initially install. X Window System We've not had good X11 coverage in the online Solaris docs in a while, mostly relying on the man pages, and upstream X.Org docs. In this release, we've integrated some X coverage into the Solaris 11.1 Desktop Adminstrator's Guide, including sections on installing fonts for fontconfig or legacy X11 clients, X server configuration, and setting up remote access via X11 or VNC. Of course we continue to work on improving the docs, including a lot of contributions to the upstream docs all OS'es share (more about that another time). Security One of the things Oracle likes to do for its products is to publish security guides for administrators & developers to know how to build systems that meet their security needs. For Solaris, we started this with Solaris 11, providing a guide for sysadmins to find where the security relevant configuration options were documented. The Solaris 11.1 Security Guidelines extend this to cover new security features, such as Address Space Layout Randomization (ASLR) and Read-Only Zones, as well as adding additional guidelines for existing features, such as how to limit the size of tmpfs filesystems, to avoid users driving the system into swap thrashing situations. For developers, the corresponding document is the Developer's Guide to Oracle Solaris 11 Security, which has been the source for years for documentation of security-relevant Solaris API's such as PAM, GSS-API, and the Solaris Cryptographic Framework. For Solaris 11.1, a new appendix was added to start providing Secure Coding Guidelines for Developers, leveraging the CERT Secure Coding Standards and OWASP guidelines to provide the base recommendations for common programming languages and their standard API's. Solaris specific secure programming guidance was added via links to other documentation in the product doc set. In parallel, we updated the Solaris C Libary Functions security considerations list with details of Solaris 11 enhancements such as FD_CLOEXEC flags, additional *at() functions, and new stdio functions such as asprintf() and getline(). A number of code examples throughout the Solaris 11.1 doc set were updated to follow these recommendations, changing unbounded strcpy() calls to strlcpy(), sprintf() to snprintf(), etc. so that developers following our examples start out with safer code. The Writing Device Drivers guide even had the appendix updated to list which of these utility functions, like snprintf() and strlcpy(), are now available via the Kernel DDI. Little Things Of course all the big new features got documented, and some major efforts were put into refactoring and renovation, but there were also a lot of smaller things that got fixed as well in the nearly a year between the Solaris 11 and 11.1 doc releases - again too many to list here, but a random sampling of the ones I know about & found interesting or useful: The Privileges section of the DTrace Guide now gives users a pointer to find out how to set up DTrace privileges for non-global zones and what limitations are in place there. A new section on Recommended iSCSI Configuration Practices was added to the iSCSI configuration section when it moved into the SAN Configuration and Multipathing administration guide. The Managing System Power Services section contains an expanded explanation of the various tunables for power management in Solaris 11.1. The sample dcmd sources in /usr/demo/mdb were updated to include ::help output, so that developers like myself who follow the examples don't forget to include it (until a helpful code reviewer pointed it out while reviewing the mdb module changes for Xorg 1.12). The README file in that directory was updated to show the correct paths for installing both kernel & userspace modules, including the 64-bit variants.

  Read the article

• Developing Schema Compare for Oracle (Part 4): Script Configuration

  - by Simon Cooper

  If you've had a chance to play around with the Schema Compare for Oracle beta, you may have come across this screen in the synchronization wizard: This screen is one of the few screens that, along with the project configuration form, doesn't come from SQL Compare. This screen was designed to solve a couple of issues that, although aren't specific to Oracle, are much more of a problem than on SQL Server: Datatype conversions and NOT NULL columns. 1. Datatype conversions SQL Server is generally quite forgiving when it comes to datatype conversions using ALTER TABLE. For example, you can convert from a VARCHAR to INT using ALTER TABLE as long as all the character values are parsable as integers. Oracle, on the other hand, only allows ALTER TABLE conversions that don't change the internal data format. Essentially, every change that requires an actual datatype conversion has to be done using a rebuild with a conversion function. That's OK, as we can simply hard-code the various conversion functions for the valid datatype conversions and insert those into the rebuild SELECT list. However, as there always is with Oracle, there's a catch. Have a look at the NUMTODSINTERVAL function. As well as specifying the value (or column) to convert, you have to specify an interval_unit, which tells oracle how to interpret the input number. We can't hardcode a default for this parameter, as it is entirely dependent on the user's data context! So, in order to convert NUMBER to INTERVAL DAY TO SECOND/INTERVAL YEAR TO MONTH, we need to have feedback from the user as to what to put in this parameter while we're generating the sync script - this requires a new step in the engine action/script generation to insert these values into the script, as well as new UI to allow the user to specify these values in a sensible fashion. In implementing the engine and UI infrastructure to allow this it made much more sense to implement it for any rebuild datatype conversion, not just NUMBER to INTERVALs. For conversions which we can do, we pre-fill the 'value' box with the appropriate function from the documentation. The user can also type in arbitary SQL expressions, which allows the user to specify optional format parameters for the relevant conversion functions, or indeed call their own functions to convert between values that don't have a built-in conversion defined. As the value gets inserted as-is into the rebuild SELECT list, any expression that is valid in that context can be specified as the conversion value. 2. NOT NULL columns Another problem that is solved by the new step in the sync wizard is adding a NOT NULL column to a table. If the table contains data (as most database tables do), you can't just add a NOT NULL column, as Oracle doesn't know what value to put in the new column for existing rows - the DDL statement will fail. There are actually 3 separate scenarios for this problem that have separate solutions within the engine: Adding a NOT NULL column to a table without a rebuild Here, the workaround is to add a column default with an appropriate value to the column you're adding: ALTER TABLE tbl1 ADD newcol NUMBER DEFAULT <value> NOT NULL; Note, however, there is something to bear in mind about this solution; once specified on a column, a default cannot be removed. To 'remove' a default from a column you change it to have a default of NULL, hence there's code in the engine to treat a NULL default the same as no default at all. Adding a NOT NULL column to a table, where a separate change forced a table rebuild Fortunately, in this case, a column default is not required - we can simply insert the default value into the rebuild SELECT clause. Changing an existing NULL to a NOT NULL column To implement this, we run an UPDATE command before the ALTER TABLE to change all the NULLs in the column to the required default value. For all three, we need some way of allowing the user to specify a default value to use instead of NULL; as this is essentially the same problem as datatype conversion (inserting values into the sync script), we can re-use the UI and engine implementation of datatype conversion values. We also provide the option to alter the new column to allow NULLs, or to ignore the problem completely. Note that there is the same (long-running) problem in SQL Compare, but it is much more of an issue in Oracle as you cannot easily roll back executed DDL statements if the script fails at some point during execution. Furthermore, the engine of SQL Compare is far less conducive to inserting user-supplied values into the generated script. As we're writing the Schema Compare engine from scratch, we used what we learnt from the SQL Compare engine and designed it to be far more modular, which makes inserting procedures like this much easier.

  Read the article

• Trouble with Samba Domain

  - by Arkevius

  I'm having a bit of trouble setting up this Samba domain correctly. I'm getting an Access Denied error when trying to add a Windows XP machine to the domain. I'll go through my scenario in detail, but for those of you wanting a TLDR summary it'll be at the bottom of this post. I have HP Proliant server with Ubuntu 12.04 LTS installed. For this particular environment, I need this server to act as a PDC, file server, and print server. I began by updating and upgrading the packages (of course). Then went to install samba, gnome-desktop, wine, and cpanm. Samba was, of course, for the PDC and file/print services. The GUI was needed because a certain software has to be installed on there that needs a GUI. Wine was needed because the software is Windows-native. And cpanm was for a perl script I have running. For Samba, I went into the smb.conf file and enabled domain logons, changed the workgroup/domain name, the logon script for a per-group basis (netlogon/%g), enabled the netlogon and profiles share, and setup a couple of custom shares for the file service. The printer was added later, and seems to be working just fine. I then restarted the services, and used the net groupmap command to ensure my unix groups were mapped correctly to the Windows groups. After this, I went to a Windows box, and was able to successfully join the domain without a problem. After some fidgeting with the software to get it running on the win boxes from the server (it's a records management system program, which stores it's database files on the server), I went to add another computer to the domain. But now it's saying Access Denied. Before when I had this trouble it was because I forgot to add the group "machines" so Samba could create machine accounts. Thinking this was the case, I manually created the machine account to test this theory. However, it would still give me an Access Denied error. That must mean it has something to do with permissions now, correct? I've been fighting with this server for the past two weeks. If it's not one thing that;s wrong, then it's something else completely different. This would be the third time I've actually reinstalled everything to start over. I'll post snippets of my system settings below. If anything else is needed, just say the word and I'll gather up the info. The unix group 'domadmin' is the Domain Admins group. Samba Administrator account administrator:x:1000:1000:Administrator,,,:/home/administrator:/bin/bash Adminstrator's groups administrator adm cdrom sudo dip plugdev lpadmin sambashare domadmin crimestar Samba's Configuration FIle (a snippet anyways) [global] workgroup = CITYPD server string = BPDServer dns proxy = no log file = /var/log/samba/log.%m max log size = 1000 syslog = 0 panic action = /usr/share/samba/panic-action %d security = user encrypt passwords = true passdb backend = tdbsam obey pam restrictions = yes unix password sync = yes passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . pam password change = yes map to guest = bad user domain logons = yes logon path = \\%L\srv\samba\profiles\%U logon script = logon.bat add machine script = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u domain master = yes usershare allow guests = yes [netlogon] comment = Network Logon Service path = /srv/samba/netlogon/%g guest ok = yes read only = yes browseable = no [profiles] comment = All Printers browseable = no path = /var/spool/samba printable = yes guest ok = no read only = yes create mask = 0700 [print$] comment = Printer Drivers path = /var/lib/samba/printers browseable = yes read only = yes guest ok = no write list = root, @lpadmin [crimestar] comment = "Crimestar DB" path = /srv/crimestar/db valid users = @domadmin, @crimestar admin users = administrator writeable = yes guest ok = no browseable = no create mask = 0666 directory mask = 0777 [crimestarfiles] path = /home/administrator/.wine/drive_c/crimestar admin users = administrator browseable = yes ls -la on /srv/samba/profiles drwxrwxrwx 2 root machines 4096 Nov 21 15:27 . drwxr-xr-x 4 root root 4096 Nov 21 15:28 .. ls -la on /srv/samba/netlogon drwxr-xr-x 6 root root 4096 Nov 21 15:30 . drwxr-xr-x 4 root root 4096 Nov 21 15:28 .. drwxr-xr-x 2 root root 4096 Nov 21 15:30 crimestar drwxr-xr-x 2 root root 4096 Nov 21 18:13 domadmin drwxr-xr-x 3 root root 4096 Nov 21 15:30 guests drwxr-xr-x 2 root root 4096 Nov 21 15:29 users GrouMap list Domain Users (S-1-5-21-2978508755-2341913247-928297747-513) -> users Domain Admins (S-1-5-21-2978508755-2341913247-928297747-512) -> domadmin Domain Guests (S-1-5-21-2978508755-2341913247-928297747-514) -> nogroup TLDR I'm getting an Access Denied error message while trying to join a windows box to a samba domain, even after I successfully joined another computer without a problem. System settings / files are quoted above. Anyone have any ideas or suggestions?

  Read the article

• Using EUSM to manage EUS mappings in OUD

  - by Sylvain Duloutre

  EUSM is a command line tool that can be used to manage the EUS settings starting with the 11.1 release of Oracle. In the 11.1 release the tool is not yet documented in the Oracle EUS documentation, but this is planned for a coming release. The same commands used by EUSM can be performed from the Database Console GUI or from Grid Control*. For more details, search for the document ID 1085065.1 on OTN. The examples below don't include all the EUSM options, only the options that are used by EUS. EUSM is user friendly and intuitive. Typing eusm help <option> lists the parameters to be used for any of the available options. Here are the options related to connectivity with OUD : ldap_host="gnb.fr.oracle.com" - name of the OUD server. ldap_port=1389 - nonSSL (SASL) port used for OUD connections.  ldap_user_dn="cn=directory manager" - OUD administrator nameldap_user_password="welcome1" - OUD administrator password Find below common commands: To List Enterprise roles in OUD eusm listEnterpriseRoles domain_name=<Domain> realm_dn=<realm> ldap_host=<hostname> ldap_port=<port> ldap_user_dn=<oud administrator> ldap_user_password=<oud admin password> To List Mappings eusm listMappings domain_name=<Domain> realm_dn=<realm> ldap_host=<hostname> ldap_port=<port> ldap_user_dn=<oud admin> ldap_user_password=<oud admin password> To List Enterprise Role Info eusm listEnterpriseRoleInfo enterprise_role=<rdn of enterprise role> domain_name=<Domain> realm_dn=<realm> ldap_host=<hostname> ldap_port=<port> ldap_user_dn="<oud admin>" ldap_user_password=<oud admin password> To Create Enterprise Role eusm createRole enterprise_role=<rdn of the enterprise role> domain_name=<Domain> realm_dn=<realm> ldap_host=<hostname> ldap_port=<port> ldap_user_dn="<oud admin>" ldap_user_password=<oud admin password> To Create User-Schema Mapping eusm createMapping database_name=<SID of target database> realm_dn="<realm>" map_type=<ENTRY/SUBTREE> map_dn="<dn of enterprise user>" schema="<name of the shared schema>" ldap_host=<oud hostname> ldap_port=<port> ldap_user_dn="<oud admin>" ldap_user_password="<oud admin password>" To Create Proxy Permission eusm createProxyPerm proxy_permission=<Name of the proxypermission> domain_name=<Domain> realm_dn="<realm>" ldap_host=<hostname> ldap_port=<port> ldap_user_dn="<oud admin>" ldap_user_password=<oud admin password> To Grant Proxy permission to Proxy group eusm grantProxyPerm proxy_permission=<Name of the proxy permission> domain_name=<Domain> realm_dn="<realm>" ldap_host=<hostname> ldap_port=<port> ldap_user_dn="<oud admin>" ldap_user_password=<password> group_dn="<dn of the enterprise group>" To Map proxy permission to proxy user in DB eusm addTargetUser proxy_permission=<Name of the proxy permission> domain_name=<Domain> realm_dn="<realm>" ldap_host=<hostname> ldap_port=<port> ldap_user_dn="<oud admin>" ldap_user_password=<oud admin password> database_name=<SID of the target database> target_user=<target database user> dbuser=<Database user with DBA privileges> dbuser_password=<database user password> dbconnect_string=<database_host>:<port>:<DBSID> Enterprise role to Global role mapping eusm addGlobalRole enterprise_role=<rdn of the enterprise role> domain_name=<Domain> realm_dn="<realm>" database_name=<SID of the target database> global_role=<name of the global role defined in the target database> dbuser=<database user> dbuser_password=<database user password> dbconnect_string=<database_host>:<port>:<DBSID> ldap_host=<oid_hostname> ldap_port=<port> ldap_user_dn="<oud admin>" ldap_user_password=<oud admin password>

  Read the article

< Previous Page | 858 859 860 861 862 863 864 865 866 867 868 869  | Next Page >