Search Results

Search found 7875 results on 315 pages for 'wired networking'.

Page 95/315 | < Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >

• Cisco SA520 to Adtran 1234 no DHCP transfer

  - by Grico

  I am trying to set up a Cisco SA520 to run DHCP on my network. I have a vendor provided switch, the Adtran 1234, and it provides DHCP for our phone systems on VLAN 200. I do not have access to the Adtran, but the vendor gave me a IP on port 1 for WAN and said port 2 should be for the "trust" side should go. I did setup a mini lab where, Adtran 1 went to SA520 WAN port, and SA520 trust 1 went to my laptop. Everything worked fine, I could ping and get internet using the DHCP scope I put on the SA520. I then unplugged my computer from SA520 trust 1 and plugged it into Adtran 2. I plugged my computer into Adtran 23 and I dont get DHCP or even a link light. If I restart my machine, I get a brief link and then it dies once the machine boots. I have tried several ports on the Adtran and none seem to work. Different cables as well. However, when I plug a phone into the Adtran, the phone boot immediately and shows link. Thoughts?

  Read the article

• Multicast doesn't seem to be working on RHEL 5.5

  - by NullUser

  I'm trying to install Oracle Grid Infrastructure on two machines. Their documentation states You must enable multicasting for the cluster on the IP address subnet ranges 224.0.0.0/24 and 230.0.1.0/24 So I ran: route add -net 224.0.0.0/24 dev eth2 route add -net 230.0.1.0/24 dev eth2 route -n produces: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 230.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 224.0.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 # and others An ifconfig eth2 shows, among other things, UP BROADCAST RUNNING MULTICAST. However, when I run their multicast test utility, it fails me: Test for Multicast address 230.0.1.0 Sep 3 19:40:39 | Multicast Failed for eth2 using address 230.0.1.0:42000 Test for Multicast address 224.0.0.251 Sep 3 19:41:10 | Multicast Failed for eth2 using address 224.0.0.251:42001 What am I doing wrong?

  Read the article

• Windows 7 and Vista Home Networked-Unable to login from Vista to Windows 7

  - by Lynn

  I set up both Vista and Windows 7 on the same workgroup. I can view Windows 7 from Vista and vice versa. I can login into Vista from Windows 7. I am unable to login to Windows 7 from Vista. When I enter the Windows 7 User name and Password on Vista, the following information appears: Logon unsuccessful: Windows is unable to log you on. Be sure that your user name and password are correct. Both are correct. Do you have any idea how I can resolve this logon issue? Thank you, Lynn

  Read the article

• tool for monitoring network traffic on Windows 7 Home

  - by Xah Lee

  for Windows 7 Home Edition: can anyone recommend a tool to monitor network traffic? either build-in or 3rd-party. I like to have a graph view (e.g. as in Task Manager) but also nice are tool that lets me see what IP/port that's incoming/outgoing. Command line is fine. Or even some tutorial. Thanks. (am old unix sys admin and web app dev. Though not much of a network admin and don't know much Windows. I need this tool just for my home PC, not in any pro capacity.)

  Read the article

• Using airport extreme base station as a wireless G to wireless N bridge

  - by micmcg

  Due to unfortunate placement of various wall outlets in my new apartment, my adsl 2 modem + router is not able to be placed next to my airport extreme base station (AEBS). I'd prefer not to run cat5 cable between them, but I still want to use the wireless N on the AEBS, because it will have a high speed NAS plugged in via gigabit ethernet so I want to maximise the wireless transfer speed to my 27" iMac. Is it possible to use one of the radios in the airport extreme to bridge the wireless G network with the router, and the wireless N radio to broadcast normally? The only traffic going over the G network should be internet (24mbps ADSL2) so it should never get saturated. Thanks

  Read the article

• Default route not on LAN

  - by jarmund

  I have a network that in principle looks like this: H1---\ /----Inet1 H2---->---GW1---< H3---/ \----GW2-----Inet2 H1 and H2 = Hosts that need access to internet with GW1 Inet1 = Internet link over 3G connection Inet2 = 5GHz link to Internet (not always up) GW1 = Works as a router, automatically picking the "best" connection between Inet1 and Inet2 (the latter via GW2). GW2 = 5GHz wifi router And here's the problem: H3 only needs internet access when Inet2 is up. What i was thinking of doing was a routing table that looks like this: route to GW2 via GW1 default route is via GW2 I first set the route to GW2 via GW1 without a problem. But when i try route add default gw 1.2.3.4 (1.2.3.4 being the IP of GW2), it complains "SIOCADDRT: No such device" Is the problem that the default gw i'm trying to set is not reachable directly? Is there a different approach that would allow me to achieve this? An alternative (and hypothetical) approach: Since H3 will be using a static IP, is it possible to do some magic with iptables on GW1 to forward any packets from H3 to GW3, thereby "tricking" H3 into using GW2 as its default router?

  Read the article

• No Outbound Internet on Windows Home Server

  - by Kyle B.

  Could someone provide some steps for me to check my internet connection on my Windows Home Server? It seems to have intermittent connectivity issues and I am unsure of how to diagnose the problem because it is a headless (no monitor, no keyboard) machine so the only way to get to the device is via remote desktop (which works fine). When connected to the machine, it doesn't pull up any microsoft.com sites and some other sites it does pull up (i.e. gmail.com) and some it doesn't (stackoverflow.com). To make matters more complicated, it has worked intermittently in the past for reasons unknown. Are there tools I can use to properly diagnose the reason for the connection failure? I can ping 127.0.0.1 just fine, I have internet working on my other router-connected machines, so I'm not sure why this one would fail. Any suggestions would be much appreciated and up-voted :) ** edit - thanks for suggestions guys, I'm going to try these tonight and will update my post. ** edit #2 - I hoping this is a more permanant fix, but I have both changed my port on the router as well as restarted the router at the same time. The internet (for the moment) appears to be working. I will be sure to try everything we have discussed should this problem persist. Thanks, Kyle

  Read the article

• How can I track down what part of pfsense is blocking website access?

  - by Chase Florell

  I've got a PFSense firewall/gateway on our network. Everything works great except for the fact that I cannot access one specific website. Pfsense is running the following packages Country Block LightSquid nmap notes squid squidGuard Strikeback I can access every single website I've ever tried aside from one that we need for business use (http://bridalnetwork.ca) here's the traceroute frodo:~ chase$ traceroute bridalnetwork.ca traceroute to bridalnetwork.ca (192.197.103.73), 64 hops max, 52 byte packets 1 rohan (192.168.5.1) 6.618 ms 1.662 ms 9.207 ms 2 * * * 3 * * rohan (192.168.5.1) 7.225 ms !H 4 rohan (192.168.5.1) 5.314 ms !H 5.701 ms !H 7.573 ms !H frodo:~ chase$ How can I figure out what the reason behind the blockage is? note: this has been tested on every computer on the network with the same results. ps: the pfsense box is 'rohan' (192.168.5.1) Here's what I get with Squid enabled and here's what I get with Squid disabled

  Read the article

• PCI Express x4 network card into PCI-Express x16 slot?

  - by Gallus

  Is it possible to plug in PCIe x4 NIC into PCIe x16 slot?

  Read the article

• How to detect VPN disconnection with vpnc?

  - by Abhinav

  What is the easiest way to detect that a vpnc connection on Linux/Ubuntu has disconnected? Manually, I think the way to detect is to check whether the interface (tun0) appears in /sbin/ifconfig output. Is there a better way to find out immediately, so that a script can be run to restart the connection?

  Read the article

• Long Gigabit Ethernet Run

  - by Timothy R. Butler

  I am trying to get an Gig-E network between two buildings that are approximately 260 ft. away. While some TRENDnet switches failed to be able to connect to each other over Cat 6 at that distance, two Netgear 5-port Gig-E switches do so just fine. However, it still fails after I put in place APC PNET1GB ethernet surge protectors at each end before the line connects to the respective switches. So I find myself wondering if I simply need to find a better surge protector that doesn't degrade the signal as much (if so, what kind would you recommend?) or if I should give up on copper and use fiber between the buildings. If I opt to go the latter route, I could really use some pointers. It looks like LC connectors are the most common, but I keep running into some others as well. A media converter on each end seems like the simplest solution, but perhaps a Gig-E switch with an SFP port would make more sense? Given a very limited budget, sticking with my existing copper seems best, but if it is bound to be a headache, a 100 meter fiber cable is something I think I can swing cost wise.

  Read the article

• Why do the IP addresses randomly change?

  - by GiddyUpHorsey

  I have a network with the following: Cable modem with static IP address Router Desktop - Win 7 VM Host - VMware ESXi 4.0 A couple of VM Guests - Windows Every now and then my Win 7 PC is unable to access some of the VMs. When I ping the VMs by their domain name their IP address shows up as the IP address of the cable modem. Sometimes I can fix it by running ipconfig /flushdns. The IP address will reset back to what it was supposed to be, but occasionally it wont work. Why does this happen and how can I fix it?

  Read the article

• Routing internet through ethernet to a computer without a Wireless adapter

  - by Decency

  I'm setting up a small home network. I have a laptop which connects to internet wirelessly- that works fine. I have a desktop connected to this laptop by an ethernet cable which I'd like to access the internet with. In the past, I have used a different laptop to do this and had no problems doing so. Both computers run Windows 7. I have tried setting up a homegroup and disabling Windows firewall, as well as restarting both computers. I can share data but my internet connection can not be accessed through the desktop. (I understand USB network adapters are cheap, I have one on the way but that doesn't solve this issue.) Any help or live chat support if you'd prefer would be appreciated. Thanks!

  Read the article

• Distribute IP packets accross different NIC queues with MSI (Message Signalled Interrupts)

  - by Ansis Atteka

  NetXtreme II BCM5709 Gigabit Ethernet NIC supports MSI feature (Message Signaled Interrupts) and it has 8 queues. Each queue has its own Interrupt handler in /proc/interrupts. What I am trying to accomplish is to tell NIC which packets should go to which queue. Questions: Is it possible to manually specify which IP packets should go to which queue by encapsulated protocol type (e.g. IPsec packets go in one queue, while TCP packets go in another queue)? If it is possible - how can I do it under Linux? If it is not possible - should I look at MSI-X capable NIC cards to solve this problem? More details: We have one Interface that is terminating IPSec and forwarding/terminating TCP connections. The IPSec packet decryption is inlined (this means that decryption is done under the same ksoftirqd/X context). We are trying to find out if we will be able to improve total performance if IPSec packets will be scheduled on another CPU than TCP packets. One more limitation is that IPSec code is not MP-safe, hence I can not run it under more than one ksoftirqd/X. By default it seems that packets are distributed/hashed by source IP over the 8 NIC queues. The bottleneck is IPSec that chokes out TCP traffic while it is decrypting/encrypting IPSec packets at ~100% CPU. OS is Ubuntu 10.10 (2.6.32-27-server) and NIC is Broadcom BCM5709.

  Read the article

• How to resolve IPs in DNS based on the subnet of the requesting client?

  - by Nohsib

  Is it possible to configure Bind9 or other DNS to resolve the domain name of a machine into different IPs based on the subnet of the requesting client? e.g. Say the same service is running on 2 different application servers at different geographical points and based on the incoming request to resolve the domain name, the name server provides the IP of the application server based on the requesting client's IP, so the service could be offered by servers that are geographically closer to the client. In short, something like a CDN but just the IP resolution part based on the client's subnet. Is this configurable in any DNS?

  Read the article

• Iomega Home Media Network Hard Drive: Accesing the data in the disk?

  - by JJarava

  Hi all! I have an Iomega Home Media Network Hard Drive, 1TB, and lately I can't access the data on the drive. The shares (both built-in and created by me) are there, the security works, but when trying to access the data I get a "The network path was not found" message which is worrying, to say the least. I'd like to know if there is a way to get the data off the disks somehow, as some of the data in the drive (ie, pictures and videos of my 1.5 yrs old son) is hard if not impossible to find otherwise. Thanks a lot Javier

  Read the article

• Constructing radiotap header and ieee80211 header structures for packet injection

  - by hektor

  I am trying to communicate between two laptop machines using Wifi. The structure of the radiotap header and ieee80211 header I am using is: struct ieee80211_radiotap_header { unsigned char it_version; uint16_t it_len; uint32_t it_present; }; /* Structure for 80211 header */ struct ieee80211_hdr_3addr { uint16_t frame_ctl[2]; uint16_t duration_id; unsigned char addr1[ETH_ALEN]; unsigned char addr2[ETH_ALEN]; unsigned char addr3[ETH_ALEN]; uint16_t seq_ctl; }; struct packet { struct ieee80211_radiotap_header rtap_header; struct ieee80211_hdr_3addr iee802_header; unsigned char payload[30]; }; /* In main program */ struct packet mypacket; struct ieee80211_radiotap_header ratap_header; struct ieee80211_hdr_3addr iee802_header; unsigned char addr1[ETH_ALEN] = {0xFF,0xFF,0xFF,0xFF,0xFF,0xFF}; /* broadcast address */ unsigned char addr2[ETH_ALEN] = {0x28,0xcf,0xda,0xde,0xd3,0xcc}; /* mac address of network card */ unsigned char addr3[ETH_ALEN] = {0xd8,0xc7,0xc8,0xd7,0x9f,0x21}; /* mac address of access point i am trying to connect to */ /* Radio tap header data */ ratap_header.it_version = 0x00; ratap_header.it_len = 0x07; ratap_header.it_present = (1 << IEEE80211_RADIOTAP_RATE); mypacket.rtap_header = ratap_header; /* ieee80211 header data */ iee802_header.frame_ctl[0] = IEEE80211_FC0_VERSION_0 | IEEE80211_FC0_TYPE_MGT | IEEE80211_FC0_SUBTYPE_BEACON; iee802_header.frame_ctl[1] =IEEE80211_FC1_DIR_NODS; strcpy(iee802_header.addr1,addr1); strcpy(iee802_header.addr2,addr2); strcpy(iee802_header.addr3,addr3); iee802_header.seq_ctl = 0x1086; mypacket.iee802_header=iee802_header; /* Payload */ unsigned char payload[PACKET_LENGTH]="temp"; strcpy(mypacket.payload , payload); I am able to receive the packets when I test the transmission and reception on the same laptop. However I am not able to receive the packet transmitted on a different laptop. Wireshark does not show the packet as well. Can anyone point out the mistake I am making?

  Read the article

• Slower wireless speed in Ubuntu 12.04 (64-bit) on Asus USB-N13

  - by PhantonTurtle

  I have an Asus USB-N13 which I use for wireless internet on my desktop. The download speed I get on Windows 7 (dual-boot) is 15.22 Mbps. On Ubuntu 12.04 (64-bit) I can only get 1.09 Mbps. I asked a question about this on the Ubuntu forums as well, but I did not get an answer. Here is the output from lsmod | grep rt which gives me, parport_pc 32866 0 rtl8192cu 103297 0 rtl8192c_common 75767 1 rtl8192cu rtlwifi 111202 1 rtl8192cu mac80211 506816 3 rtl8192cu,rtl8192c_common,rtlwifi cfg80211 205544 2 rtlwifi,mac80211 parport 46562 3 parport_pc,ppdev,lp I installed the drivers from Realtek (my chipset is Realtek, not Ralink) but that did not work.

  Read the article

• Does VPN connection on virtual machine bypass host VPN?

  - by Daniel Valland Torgrimsen

  I wanted to see if i could channel my traffic trough two vpns, so as an experiment i set up a windows xp virtual machine in virtualbox (using NAT shared network setting), connected the host pc(windows 7) to a vpn, and then the virtual machine to another vpn. this seams to work fine. However, my question is, is the traffic sent trough both vpn servers, or is the virtual machines vpn bypassing the host machines vpn connection? thanks.

  Read the article

• Why do Ping and Dig provide different IP address than nslookup?

  - by user1032531

  When pinging my domain name which points to my home public IP from two different servers on my LAN, it shows them pinging different IP. Further investigation shows dig and nslookup providing different results. See below. A little history. My IP used to be 11.22.33.444 and is hosted by Comcast. I changed routers, and it somehow got changed to 55.66.77.888. I've since updated my 1and1 domain name to point to the 55.66.77.888. desktop is a basic server, runs the web server, and connects wirelessly to my LAN. laptop is a GUI and connected via CAT5. Both operate Centos6.4. My old router was a D-Link, and used their "Virtual Server" feature to pass port 80 to desktop. My new router is a Linksys, and I use their "Port Forwarding" feature to pass port 80 to desktop (however, I haven't gotten this part working yet). What is going on??? Why the different IPs? Obviously, it most somehow be stored on the server, but why does the actual machine even know the public IP since it is on a LAN? How do I purge the old IP? [root@desktop etc]# dig +short myDomain.com 11.22.33.444 [root@desktop etc]# nslookup www.myDomain.com Server: 8.8.8.8 Address: 8.8.8.8#53 Non-authoritative answer: Name: www.myDomain.com Address: 55.66.77.888 [root@desktop etc]# dig myDomain.com ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6_4.6 <<>> myDomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 13822 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;myDomain.com. IN A ;; ANSWER SECTION: myDomain.com. 16031 IN A 11.22.33.444 ;; Query time: 21 msec ;; SERVER: 8.8.8.8#53(8.8.8.8) ;; WHEN: Mon Oct 21 04:36:52 2013 ;; MSG SIZE rcvd: 44 [root@desktop etc]# [root@laptop ~]# dig +short myDomain.com 55.66.77.888 [root@laptop ~]# nslookup www.myDomain.com Server: 192.168.0.1 Address: 192.168.0.1#53 Non-authoritative answer: Name: www.myDomain.com Address: 55.66.77.888 [root@laptop ~]#

  Read the article

• Weird Network Behavior of Home Router

  - by Stilgar

  First of all I would like to apologize because what you are going to read will be long and confusing but I am fighting this issue for 3 days now and am out of ideas. At home I have the following setup 50Mbps Internet connects into a home router A 2 desktop computers connect to router A via standard FTP LAN cables including one where the cable is ~20m long. a second router B connects to router A via standard FTP LAN cable X (~20m long). several devices connect to the wireless network of router B and there are a couple of desktop computers connected to it through FTP LAN cables. For some reason computers connected to router B when it is connected via cable X have very slow Internet connection. It is like 5 times slower than what is expected. This is the actual problem I am trying to solve. Interesting facts If a computer is connected to cable X directly instead of through router B the Internet speed is just fine (up to the 50Mbps I get from the ISP). Tested with two computers. I have tried replacing router B with another router C and the problem persists. If I connect router B via another cable to the same ports with the same settings everything seems to work fine and computers connected to router B have quite fast Internet I have tested mainly via Speedtest.net but I have also achieved similar speeds when downloading a file The upload speed is quite higher than the download speed in all cases. Note that my ISP usually has higher upload speed (unless it manages to hit the 50Mbps cap) It seems like the speed when connecting through router B with cable X is reduced 4-5 times no matter what the original speed is. For example via router B I get 10Mbps speed to local servers where I get 50Mbps when connected on router A. If I use a distant server where the ISP is only able to provide 25Mbps I get 4-5Mbps on router B. WiFi is slower than LAN on both routers (which is normal) but the reduced speed is reduced proportionally for WiFi. In addition the upload speed is normally higher from the ISP and it is also reduced proportionally. I have tried two different network configurations. One where I have NAT behind NAT where router B connects to router A via the WAN port and has its own DHCP. Second where router B connects to router A via standard LAN port and has DHCP disabled. In this configuration router B serves as a switch and the Network Gateway for computers connected to router B is the internal IP address of router A. Both configurations work just fine but both manifest the reduced speed issue. pings seem to work just fine As far as I can tell none of the cables is crossed The RJ45 setup for cable X orange orange-white brown brow-white blue blue-white green green-white This is a big problem for me since cable X passes through walls and floors and is very hard to replace. I also may have gotten some of the facts wrong because I am almost going crazy with this issue and testing includes going several floors up and down the staircase. One hypothesis I came up with is that the cable is defective in such a way that the voltage from the router affects its performance. When it is connected to a computer it performs just fine but the router has less power. Related hypothesis includes the cable being affected by electricity cables in the walls when the voltage is low. (I know nothing about electricity) So any ideas what to do, what to test or what the issue may be?

  Read the article

• How can ICS in Windows 7 be managed via command line, scripts, config files, etc.?

  - by Skya

  I've been using ICS successfully for years, but now I'm looking for a way to control it through something else than the GUI in Control Panel\Network and Internet\Network Connections - Connection Properties: I want to do everything that the encircled checkbox does, without touching the GUI. But what does the checkbox do? Microsoft don't provide specific information and the most helpful forum post I've found is from 2003. Assuming that some of the advice is still valid, I've come to the conclusion that ICS is broken down into 6 parts that have to be set up individually: the sharedAccess service interface settings firewall rules a static route dnsproxy autodhcp I've already learned that the service can be started/stopped with the command net start/stop sharedAccess and that netsh is a good tool for changing the interface settings and the firewall rules. But I don't understand how ICS handles routing and DNS. All hosts in my network are configured statically, so I don't care much about autodhcp. Thanks for your help! EDIT: I've spent the whole day scanning through ProcMon and I've seen reads/writes to both the registry and the filesystem and it is difficult to determine what parts of it actually make ICS work. I'm trying to look for an API instead. I'm looking into this right now, but I still want to know more about the inner workings.

  Read the article

• Spanning-tree setup with incompatible switches

  - by wfaulk

  I have a set of eight HP ProCurve 2910al-48G Ethernet switches at my datacenter that are set up in a star topology with no physical loops. I want to partially mesh the switches for redundancy and manage the loops with a spanning-tree protocol. However, our connection to the datacenter is provided by two uplinks, each to a Cisco 3750. The datacenter's switches are handling the redundant connection using PVST spanning-tree, which is a Cisco-proprietary spanning-tree implementation that my HP switches do not support. It appears that my switches are not participating in the datacenter's spanning-tree domain, but are blindly passing the BPDUs between the two switchports on my side, which enables the datacenter's switches to recognize the loop and put one of the uplinks into the Blocking state. This is somewhat supposition, but I can confirm that, while my switches say that both of the uplink ports are forwarding, only one is passing any real quantity of data. (I am assuming that I cannot get the datacenter to move away from PVST. I don't know that I'd want them to make that significant of a change anyway.) The datacenter has also sent me this output from their switches (which I have expurgated of any identifiable info): 3750G-1#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 5 (GigabitEthernet1/0/5) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 0018.73d3.yyyy Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/5 Root FWD 4 128.5 P2p Gi1/0/6 Altn BLK 4 128.6 P2p Gi1/0/8 Altn BLK 4 128.8 P2p and: 3750G-2#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 6 (GigabitEthernet1/0/6) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 000f.f71e.zzzz Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/1 Desg FWD 4 128.1 P2p Gi1/0/5 Altn BLK 4 128.5 P2p Gi1/0/6 Root FWD 4 128.6 P2p Gi1/0/8 Desg FWD 4 128.8 P2p The uplinks to my switches are on Gi1/0/8 on both of their switches. The uplink ports are configured with a single tagged VLAN. I am also using a number of other tagged VLANs in my switch infrastructure. And, to be clear, I am passing the tagged VLAN I'm receiving from the datacenter to other ports on other switches in my infrastructure. My question is: how do I configure my switches so that I can use a spanning tree protocol inside my switch infrastructure without breaking the datacenter's spanning tree that I cannot participate in?

  Read the article

• No network connectivity for my CentOS 6 installed in VMWare Fusion in MacOSX Lion

  - by gilzero

  I installed CentOS 6.2 (CentOS-6.2-x86_64-minimal.iso) with VMWare Fusion(Version 4.1.2). (Not with EasyInstall). I am using MacOSX Lion, connect to internet via WIFI. The centos installed does not have network connectivity. *How may I configure it to connect to wifi? * Thanks for any help. Below is screenshot of ifconfig: With the setting Network Adapter, I tried both NAT and Bridged WiFi.

  Read the article

• Should I remove all unmanged switches from my network?

  - by IMAbev

  I have a office network with approx 150 devices (computers/printers/ip phones). Almost all of the end point devices have straight run Cat5e from my Hp switches directly to the device. IP phones for each end user sit between the hp switch and computer. (hp switch - in to phone out of phone in to computer) While I have gotten rid of most of them, I still have a couple linksys unmanaged switches that split off to 2 or more devices. I have heard various reasons for removing these switches but not entirely sure if it actually degrades the network. I agree that eliminating these switches certainly cleans up the network from a management standpoint. Are these unmanaged switches bad for my network? Is there a clear advantage to having 'home run' cable runs to each of my end point devices?

  Read the article

< Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >