Search Results

Search found 7875 results on 315 pages for 'wired networking'.

Page 100/315 | < Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >

• Should I enabled 802.3x hardware flow control?

  - by Stu Thompson

  What is the conventional wisdom regarding 802.3x flow control? I'm setting up a network at a new colo and am wondering if I should be enabling it or not. My oh-cool-a-bright-and-shiny-new-toy self wants to enable it, but this seems like one of those decisions that could blow up in my face later on. My network: An HP ProCurve 2510G-24 switch A pair of Debian 5 HP DL380 G5's with built-in NC373i 2-port NIC LACP'd as one link. 9000 jumbo frames enabled. (Application) A pair of hand-built Ubuntu server with 4-port Intel Pro/1000 LACP'd as one link. 9000 jumbo frames enabled. (NAS) A few other servers with with single 1Gbps ports, but one with 100Mbps. Most of this kit is 802.3x. I've been enabling it as I go along, and am about to test the network. But as my 'go live' day nears, I am worried about the 802.3x decision as I've never explicitly used it before. Also, I've read some 10-year old articles out there on the Intertubes that warn against using flow control. Should I be enabling 802.3x hardware flow control?

  Read the article

• Failed to mount to nfs server with "Program not Registered"

  - by Farrel

  I'm trying to setup nfs server on Fedora 17 and I'm getting "Program not Registered" error when I'm trying to mount. I guess the main reason for this is rpcbind. I'm a newbie in linux, so I don't know what info should I provide you with. Here is some info that might be useful. rpcinfo -p program vers proto port service 100000 4 tcp 111 portmapper 100000 3 tcp 111 portmapper 100000 2 tcp 111 portmapper 100000 4 udp 111 portmapper 100000 3 udp 111 portmapper 100000 2 udp 111 portmapper 100005 1 udp 20048 mountd 100005 1 tcp 20048 mountd 100005 2 udp 20048 mountd 100005 2 tcp 20048 mountd 100005 3 udp 20048 mountd 100005 3 tcp 20048 mountd 100024 1 udp 42223 status 100024 1 tcp 50054 status cat /etc/exports /home/Farrel/prog 192.168.xxx.xxx (ro,sync) service nfs status Redirecting to /bin/systemctl status nfs.service nfs-server.service - NFS Server Loaded: loaded (/usr/lib/systemd/system/nfs-server.service; enabled) Active: active (exited) since Fri, 02 Nov 2012 09:29:04 +0300; 5min ago Process: 924 ExecStartPost=/usr/lib/nfs-utils/scripts/nfs-server.postconfig (code=exited, status=0/SUCCESS) Process: 909 ExecStart=/usr/sbin/rpc.nfsd $RPCNFSDARGS ${RPCNFSDCOUNT} (code=exited, status=0/SUCCESS) Process: 885 ExecStartPre=/usr/sbin/exportfs -r (code=exited, status=0/SUCCESS) Process: 864 ExecStartPre=/usr/lib/nfs-utils/scripts/nfs-server.preconfig (code=exited, status=0/SUCCESS) CGroup: name=systemd:/system/nfs-server.service Warning: Journal has been rotated since unit was started. Log output is incomplete or unavailable. Firewall is disabled on both systems. I spent a lot of time reading on the topic but all manuals on setting up nfs server lead to "Program not Registered" error. Any how-to-fix-it ideas?

  Read the article

• Loadbalance UDP traffic with session affinity and way to take servers in & out of rotation

  - by William

  What is the best way to go about load balancing UDP traffic among a whole bunch of servers, while keeping session affinity based on the users' IP? I need to also be able to take servers in and out of rotation for new clients, so when they join for the first time, they get put on a server in a list of available servers, and clients already connected would stay connected to their specific server. I have written the software to maintain a list, but I can't seem to find anything that would perform this functionality. If you need the context, this is to facilitate game tournaments for Minecraft: Pocket Edition, which is done with UDP traffic, I cannot change the protocol. And, because tournaments open and close, I need to be able to place players on their proper servers. Performance is also a priority, I have a program to do this but it is very bloated and slow. Thanks for any help! William

  Read the article

• Subdomains for different applications on Windows Server 2008 R2 with Apache and IIS 7 installed

  - by Yusuf

  I have a home server, on which I have installed Apache, and several other applications that have a Web GUI (JDownloader, Free Download Manager). In order to access each of these apps (whether be it from the local network or the Internet), I have to enter a different port, e.g., http://server:8085 or http://xxxx.dyndns.org:8085 for Apache http://server:90 or http://xxxx.dyndns.org:90 for FDM http://server:8081 or http://xxxx.dyndns.org:8081 for JDownloader I would like to be able to access them using sub-domains, e.g, http://apache.server or http://apache.xxxx.dyndns.org for Apache, http://fdm.server or http://fdm.xxxx.dyndns.org for FDM, http://jdownloader.server or http://jdownloader.xxxx.dyndns.org for JDownloader First of all, would it be possible like I want it, i.e., both from LAN and Internet, and if yes, how? Even if it's possible only for Internet, I would like to know how to do it, if there's a way.

  Read the article

• 2 nics. 2 Defaults Gateways

  - by andre.dias

  Here is my scenario: i have this server with 2 nics, each one with different IPs, connected to differents routers. Almost everything is configured whe way i need. Traffic coming from eth0 exits using eth0, traffic coming from eth1 exits using eth1. And there is a default gateway configured. $route: default IP 0.0.0.0 UG 0 0 0 eth0 With this configuration, the traffic generated in the server is going out using eth0 (lynx www.google.com for example). The problem is: the Internet link from eth0 went down today. The traffic coming from eth1 was ok...no problem. But the traffic generated in the server was a problem...the default gateway was out...no access do the Internet anymore (no more lynx www.google.com) So i added a new default gateway configuration, pointing to eth1. For 30 minutes i kept that way...2 default gateways, but just one was "working"...and everything was working just fine. But then i removed de eth0 gateway entry because, well, 2 default gateways is kind of weird. My question: is there any problem on keeping these 2 default gateways, one for each? So i don´t need to do nothing when one link go down again? $route: default IP1 0.0.0.0 UG 0 0 0 eth0 default IP2 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Linux Transparent Bridge for Network

  - by Blackninja543

  I am attempting to set up a semi-transparent bridge. I say semi because I want it to act as a transparent tap for all traffic moving through both sides of the bridge. What I also want is to have the "green zone" accessible to a web interface for the bridge that will display all results of the IDS and other network monitoring tools. My example would be as such: eth0 <--> bridge(br0) <--> eth1 The entire network would be on the same subset however anything coming from eth0 to eth1 would be accepted. The only time anything would be drop is if the eth0 attempted to access br0. If someone attempts to access the web interface on br0 through eth1 it will succeed. My biggest problem I feel is if I attempt to block anything from eth0 to br0 this will drop the bridge all together.

  Read the article

• Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem

  - by zchads

  Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem. Hardware Information: Buffalo Wireless Router/access point, Model: WZR-HP-G300NH-AP DSL Modem: Generic (actually not sure of manufacture). Service Provider: TOT (Thailand) Laptop-1: Windows XP and Belkin PCMIA Network Card Laptop-2: Windows XP unknown network card & Wifi Laptop-3: Windows 7 unknown network card & Wifi Outline of Problem/actions taken: After a recent power failure the router and laptop-1 connected to router were no longer able to access the internet. Actions taken to try and recover internet access: Using Laptop-1 tried to configure Router with PPPoe settings using software from Router Manufacture. During the installation process a Timeout error was experienced, unable to connect to WAN. Used Internet Explorer to communicate directly with Router using IP address. Changed settings to use PPPoe settings given by ISP. Router was not able to communicate with Internet. Repeated steps 1-4 again with no success. Reset Router and DSL modem. Repeated steps 1-4 again still no success. Tried connecting Laptop-1 directly to DSL to gain access to internet to research problem. No Network connection with DSL could be established…connection would be established for a second and then be lost and didn’t appear long enough to actually connect to DSL. Replugged LAN back into Router and connection was regained with laptop-1. Replugged Laptop-1 directly into DSL and again unable to establish network connection. Uninstalled network card and all of its drivers on Laptop-1. Reinstalled network card and drivers and tried connecting directly to DSL. Still unable to make network connection. Plugged DSL into Laptop-3 and Internet connection was established. Being Laptop-3 does not have a CD-Rom, Laptop-2 was tried to connect to the router. With Laptop-2 steps 1-7 ended up being repeated without success. Tried plugging Laptop-2 directly into DSL and again no network connection could be established. Using Laptop-3 with a direct connection to DSL downloaded latest Router FW. Installed router FW using Laptop-1. Tired the installation process again without success. Being desperate reinstalled OS on Laptop-1 still not success. Tried using “ipconfig” with router to see what was going on without success. With laptop-1 connected to DSL went through the “ipconfig /…” inputs to see if anything made a difference. Being the network card was not able to make a connection this provide very little information “media disconnected”. So now I have a router and two laptops which are unable to connect to the internet and sure could use some advice/help.

  Read the article

• How can I get my routers to forward ports correctly?

  - by Giffyguy

  My network currently looks like this (simplified): Note that Router #2 is connected to the LAN interface of Router #1. This should be familiar to anyone who has seen a standard static-IP setup with an additional firewall for a residence or other small building. Router #1 is actually my cable gateway, but since it is a fully functional router/firewall, I am going to refer to it as a router. Now, I need to open various ports in both firewalls for incoming communication to my server - port 80 is a good example. So I've opened up port 80 in Router #2, and so far all incoming traffic at the public IP X.X.X.129 is being routed correctly. The problem is that I also need my server to respond to incoming traffic at the public IP X.X.X.130 on the WAN interface of Router #1. Naturally, I can't just tell Router #1 to forward port 80 to another public IP. Port forwarding is only supported when the traffic is being directed to the LAN subnet. I am willing to restructure my network topology if required, with the following conditions: Router #1 cannot have its WAN IP reassigned - X.X.X.130 is mandatory. Router #1 cannot be moved or disconnected from the cloud. The server cannot be given a second IP address. I would prefer the server to have a private IP address - e.g. 10.0.0.10 I'd like to keep Router #2, but it can have a private IP - e.g. 10.0.1.10 Following these rules, I need to get my server to receive incoming traffic on port 80 from both public IP addresses. Does anyone on SU know if this is possible? So far my only theories have been to set up a static route on either router, or to somehow combine my two subnets into a single subnet.

  Read the article

• Slower wireless speed in Ubuntu 12.04 (64-bit) on Asus USB-N13

  - by PhantonTurtle

  I have an Asus USB-N13 which I use for wireless internet on my desktop. The download speed I get on Windows 7 (dual-boot) is 15.22 Mbps. On Ubuntu 12.04 (64-bit) I can only get 1.09 Mbps. I asked a question about this on the Ubuntu forums as well, but I did not get an answer. Here is the output from lsmod | grep rt which gives me, parport_pc 32866 0 rtl8192cu 103297 0 rtl8192c_common 75767 1 rtl8192cu rtlwifi 111202 1 rtl8192cu mac80211 506816 3 rtl8192cu,rtl8192c_common,rtlwifi cfg80211 205544 2 rtlwifi,mac80211 parport 46562 3 parport_pc,ppdev,lp I installed the drivers from Realtek (my chipset is Realtek, not Ralink) but that did not work.

  Read the article

• Using two ports on my ZyXel USG gateway to patch two devices together?

  - by Matthew Beza

  I don't know if this is possible but it would save me many long drives! I have drawn, with my epic MS Paint skills, my current setup. I have a ZyXel USG300 Gateway with a built in 5 port switch. It supports bridging, tunnles, VLANs, etc.. I have a Cisco WLC2112 plugged into port 6 (P6). The cisco is set to 192.168.6.2 and P6 is set to 192.168.6.1. This works but I need to incorporate a Nomadix AG3000 to handle guests. (Router (A) in the picture). So I need the Cisco WLC2112 to use the Nomadix as if it where plugged into it's LAN port. Right now the Nomadix WAN Port is plugged into (P2) on the ZyXel, and the Nomadix LAN port is plugged into (P3). Is it possible to set something up where (P3) and (P6) are somehow "Patched" as if the Cisco was plugged directly into the Nomadix LAN port? Basically making the ZyXel a fancy Cat5e coupler?

  Read the article

• VMware vSwitches and Dell PowerConnect BPDU guard

  - by dunxd

  I am using two Dell PowerConnect 6248 switches to connect a VMware host vSwitch. A discussion of config of Cisco switches for use with VMware advises to set physical ports connected to vSwitch with bpduguard and portfast. However, Dell switches don't have the bpduguard setting for individual ports. I can switch it off globally for all portfast ports, but I don't think I want to do that. Should I: Disable STP on the vSwitch connected ports? Leave STP on and enable portfast on the ports, and forget about bpduguard? Disable bpduguard on all portfast ports via global config Do something else? See also: VMware vSwitches and spanning tree

  Read the article

• NFS performance troubleshooting

  - by aix

  I am troubleshooting NFS performance issues on Linux, and I'm looking at the following nfsiostat output: host:/path mounted on /path: op/s rpc bklog 96.75 0.01 read: ops/s kB/s kB/op retrans avg RTT (ms) avg exe (ms) 86.561 1408.294 16.269 0 (0.0%) 34.595 89.688 write: ops/s kB/s kB/op retrans avg RTT (ms) avg exe (ms) 10.113 326.282 32.265 0 (0.0%) 19.688 72446.246 What exactly is the meaning of avg RTT (ms) and avg exe (ms)? avg exe for writes is 72 seconds(!) -- would you say this is abnormal and, if so, how do I go about troubleshooting this further? I'm using NFS over TCP. Both the client and the server are on the same GigE LAN.

  Read the article

• Network / Internet diagnostic tool to locate an error?

  - by Jesper

  Hi, I’m facing some difficulties with the Internet / network at my work and I have trouble locating the precise error and when and how it occurs. The problem is that the client machines in the house sporadic is disconnected to the Internet. I’m some what new so I haven’t that much inside in the network and apparently neither has my predecessor. What I am requesting and hoping you guys knows about is, if there exist some kind of network monitor tool I can install and run and it will periodically check the network, the Internet connection etc. and record to logs. Then, if there suddenly arises a problem some time of the day in some part of the network or the Internet connection, I can check it perhaps the next day. I’ve just downloaded and installed Microsoft Network Monitor 3.3 application and hopeful it can give me some answers on where the instability is located but I still would like a tool to make different checks and test in some time interval. Do anyone know about such a program or another kind of performance / diagnostic tool / method I can use? Sincere Jesper

  Read the article

• How to set WAN side buffers for WRT54GL running Tomato Firmware

  - by Vickash

  I've recently set up a machine running m0n0wall to try and fight buffer bloat and do some traffic shaping. It was more convenient (geographically speaking) to connect the cable modem directly to my old WRT54GL, then pass everything to the m0n0wall machine and have that do the real routing work. It took a bit of work, but it's working pretty well. I have a cable connection. I have m0n0wall set up to utilize only 90% of the specified speed of my subscription, which is fine. But I've noticed that at certain times of the day (possibly when my true bandwidth drops below that 90%), there's more latency if the connection is used heavily, and traffic shaping doesn't seem to work as well. I suspect this is caused by the buffers on the WRT54GL still being unnecessarily large. If the connection is working as expected, they won't get filled, but in times of reduced bandwidth they would. Does anyone know the command I need to execute, on the WRT54GL running Tomato Firmware, to reduce the buffers on the WAN interface to the minimum size possible?

  Read the article

• Can I be a wireless server WITHOUT offering internet?

  - by Kenny Hendrick

  I would like to pull into a truck stop and offer a folder of free documentaries to quell some of the ignorance LOL I run Linux ";-) Very happy to have made that switch by the way...and have an internal wireless in the laptop but my bus has an antenna on the roof which I connect via usb to create a wireless signal (this is the one I'd like to focus on since it will offer the most reach to all those truckers out there. My question is this. I'm running apache2 and have a bunch of videos tossed into the www folder and can access it locally and would like others that frown on paying to use the truckstops slow internet service and would like an alternative by simply logging onto me and getting the narrow content I offer freely without passwords and the like. Has anyone a good means of doing this? p.s. I've done this in the past but am getting old and forgetful (my crutch)

  Read the article

• Linux clients and Windows Servers can connect but not windows clients

  - by Mustafa Ismail Mustafa

  This is driving me insane because I can't make head or tails of it. We have two DCs (W2K3 SP1) and I'v tried this once on each machine as a sanity check. DHCP is being served by either one of the machines and all machines get an address no problem. The servers can connect/ping/browse to the www and so can all our linux clients. But NONE of our windows clients (all windows 7). I can do anything within the network, I can even ping the firewall/router but nothing from the windows clients is leaving the confines of our subnet. I don't get it. The linux and windows clients are both served from the same DHCP server, the gateway is the same, everything is the same. Anyone care to take a shot at how to resolve this? I tried adding explicit routes at the clients, but still no go. TIA SMIM

  Read the article

• How to get Windows 7 to automatically connect to an ad-hoc network?

  - by George Edison

  I have two machines - one is running Ubuntu 12.04 64-bit and the other is running Windows 7 Starter Edition (32-bit). The Ubuntu machine is connected to the Internet via the eth0 interface. That machine also has a wireless network interface (wlan0) that is currently functioning as an ad-hoc network. I can connect to the ad-hoc network just fine with the Windows machine but each time I wish to do so, I must manually initiate the connection and enter the password. Is there some way to instruct Windows to automatically connect to this network (an option I have for standard wireless networks but not ad-hoc networks)?

  Read the article

• OpenVZ multiple networks on CTs

  - by picca

  I have Hardware Node (HN) which has 2 physical interfaces (eth0, eth1). I'm playing with OpenVZ and want to let my containers (CTs) have access to both of those interfaces. I'm using basic configuration - venet. CTs are fine to access eth0 (public interface). But I can't get CTs to get access to eth1 (private network). I tried: # on HN vzctl set 101 --ipadd 192.168.1.101 --save vzctl enter 101 ping 192.168.1.2 # no response here ifconfig # on CT returns lo (127.0.0.1), venet0 (127.0.0.1), venet0:0 (95.168.xxx.xxx), venet0:1 (192.168.1.101) I believe that the main problem is that all packets flows through eth0 on HN (figured out using tcpdump). So the problem might be in routes on HN. Or is my logic here all wrong? I just need access to both interfaces (networks) on HN from CTs. Nothing complicated.

  Read the article

• tomato firmware unstable when I am connected to Chromecast

  - by Graviton

  I have an Asus RT-N12D1, and I installed the tomato firmware by shibby ( version tomato-K26-1.28.RT-N5x-MIPSR2-112-Max.trx). However I found that the connection can be really unstable. Whenever I stream youtube videos on TV via Chromecast ( I tried both the cast from iPad and Win7, both can reproduce the problem), the router will frequently restart itself, leading to a loss of connection and subsequent reconnection. I want to get this problem fixed, but I don't know how. Is there anyway where I can troubleshoot what is the real problem, or is there anyway I can collect enough log information so that I can then present to the original developer for a fix ( maybe)?

  Read the article

• How to specify what network interface to use with TTCP or IPERF?

  - by Sammy

  The PC has two Gigabit Ethernet ports. They function as two separate network adapters. I'm trying to do a simple loopback test between the two. I've tried TTCP and IPERF. They're giving me hard time because I'm using the same physical PC. Using pcattcp... On the receiver end: C:\PCATTCP-0114>pcattcp -r PCAUSA Test TCP Utility V2.01.01.14 (IPv4/IPv6) IP Version : IPv4 Started TCP Receive Test 0... TCP Receive Test Local Host : GIGA ************** Listening...: On TCPv4 0.0.0.0:5001 Accept : TCPv4 0.0.0.0:5001 <- 10.1.1.1:33904 Buffer Size : 8192; Alignment: 16384/0 Receive Mode: Sinking (discarding) Data Statistics : TCPv4 0.0.0.0:5001 <- 10.1.1.1:33904 16777216 bytes in 0.076 real seconds = 215578.95 KB/sec +++ numCalls: 2052; msec/call: 0.038; calls/sec: 27000.000 C:\PCATTCP-0114> On the transmitter end: C:\PCATTCP-0114>PCATTCP.exe -t 10.1.1.1 PCAUSA Test TCP Utility V2.01.01.14 (IPv4/IPv6) IP Version : IPv4 Started TCP Transmit Test 0... TCP Transmit Test Transmit : TCPv4 0.0.0.0 -> 10.1.1.1:5001 Buffer Size : 8192; Alignment: 16384/0 TCP_NODELAY : DISABLED (0) Connect : Connected to 10.1.1.1:5001 Send Mode : Send Pattern; Number of Buffers: 2048 Statistics : TCPv4 0.0.0.0 -> 10.1.1.1:5001 16777216 bytes in 0.075 real seconds = 218453.33 KB/sec +++ numCalls: 2048; msec/call: 0.037; calls/sec: 27306.667 C:\PCATTCP-0114> It's responding alright. But why does it say 0.0.0.0? Is it passing through only one of the network adapters? I want 10.1.1.1 to be the server (receiver) and 10.1.1.2 to be the client (transmitter). These are the IP addresses assigned manually to each network adapter. How do I specify these addresses in TTCP? There is also the IPERF tool which has the -B option. Unfortunately I've been only able to use this option to bind the server to the 10.1.1.1 address. I was unable to bind the client to the 10.1.1.2 address. I might be doing it wrong. Can the -B option be used for both the server as well as the client side? What does the syntax look like for the client?

  Read the article

• monitor network bandwidth via ssh

  - by ServerSideX

  I'm running a Centos 6.4 server with cPanel. WHM (admin side panel) shows about 100GB of bandwidth this month. However, the server's RTG shows 3.4TB last 30 days, 121GB past 24 hours alone. Doesn't make sense. I'm trying to trace the cause of this. It's a shared web hosting server for approximately 300 domains. I would appreciate help tracing this down somehow. I utilize CSF firewall and Configserver exploit scanner as well. Day http://s10.postimg.org/ti1qhj5mx/day.png Week http://s7.postimg.org/8ho8kds57/week.png

  Read the article

• How do I make dnsmasq serve IP addresses via IPoIB?

  - by Matt

  I have a cluster farm that I'm setting up. The nodes (computers in the farm) are connected via ethernet & IP over Infiniband. I'm needing to netboot the nodes and thought dnsmasq would fit well as it provides all the features including support for DHCP over IB and it works great for our ethernet setup. However, I can't seem to get it to provide IP addresses to the infiniband adaptors on the nodes. Each node is running an Ubuntu desktop 12.04 LTS. The dnsmasq server is running on ubuntu server 12.04LTS and has the following test config: dhcp-authoritative domain-needed bogus-priv expand-hosts no-hosts domain=local dhcp-range=eth0,10.0.0.10,10.0.0.255,12h dhcp-option=eth0,3,10.0.0.1 dhcp-range=ib0,10.1.1.10,10.1.1.255,12h dhcp-option=ib0,3,10.1.1.1 log-queries log-dhcp IPoIB works between nodes when configured statically but not with dhcp. On the nodes the file /etc/network/interfaces contains auto lo iface lo inet loopback auto ib0 iface ib0 inet dhcp #iface ib0 inet static #address 10.1.1.5 #netmask 255.0.0.0 up echo connected >`find /sys -name mode | grep ib0` Is there something I need to do on the client or server end to make this work?

  Read the article

• Good way to run commands on remote computer without its own public-facing IP address (Linux Centos)

  - by Chris Dutrow

  Have a few computers running Linux Centos 6.4. They are connected to an unmanaged switch, which in turn, is connected to a router (Verzion Fios issue). What is a good way to "log in" to one of the computers so that I can run commands? Do I need to use SSH, or something different? Since the computers do not have their own public-facing IP addresses, do I need to set up some kind of port forwarding within the router? What is a simple, reliable way to accomplish this? Thanks so much!

  Read the article

• Connect a PC to Mac OS X Server

  - by Paul Sheldrake

  I'm trying to connect to a server at work which is run on a Mac but I have a PC (windows 7) at home. I have path to connect in the format of afp://server.com/files. Is there a client that I need to install on my PC that I can use to login? Thanks, Paul

  Read the article

• How to Set Linux Bonding Interface to Gigabit

  - by Kyle Brandt

  I have enabled Linux active backup mode bonding. Each interface is a gigabit interface, but the bond interface seems to end up at 100 Megabit: bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full. ... bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON ... bonding: bond0: backup interface eth1 is now up ethtool apparently can't provide info on bond: sudo ethtool bond0 Settings for bond0: No data available So does this mean I am operating at 100 or 1000 Megabit (My guess is 1000)? If it is only 100, what options in the ifcfg scripts or the modprobe bonding options do I need to sett to make it 1000?

  Read the article

< Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >