Search Results

Search found 489 results on 20 pages for 'fernando sbs'.

Page 1/20 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • SBS 2008 BPA Warnings After Migration From SBS 2003

    - by Nicholas Piasecki
    We just finished a we-know-just-enough-to-be-dangerous migration from SBS 2003 to SBS 2008, and things seem to have gone relatively smoothly. After running the SBS 2008 Best Practices Analyzer on the destination server, we've got three warning messages, and I can't tell if they're important or not. First, the easy one: SMTP Port (TCP 25 Status): The Edgetransport.exe process should listen on SMTP port 25, but that port is owned by the process. I don't think that this one is a big deal--e-mail is flowing through the SMTP connector. Since there are two spaces between "the" and "process," I'm assuming that for some reason BPA just couldn't figure out the owning process name and this is just some sloppy programming when displaying the message. (Indeed, on subsequent runs of the BPA this message goes away, and other times it comes back.) Now, two more scary sounding ones: No DNS name server records: There are no DNS name server (NS) resource records in the _msdcs sub-domain in the forward lookup zone for Windows SBS 2008. and, similarly, No DNS name server records: There are no DNS name server (NS) resource records in the _msdcs zone for Windows SBS 2008. Now for these two, everything appears to be functioning correctly--but I'm assuming this is a weird state as a result of the SBS 2003 to 2008 migration. Can anyone provide any pointers on how to fix it, or whether or not it can be safely ignored? Thanks!

    Read the article

  • Can't uninstall SBS 2003 in sbs 2003 -> sbs 2008 migration

    - by ChrisMuench
    I'm trying to remove sbs from my sbs 2003 server. Also I'm logged in as Administrator. However When I start to go through the wizard it gives me the following error. You must be a member of the Domain Admins, Schema Admins, and Enterprise Admins group. I then did some research and found this (http://support.microsoft.com/kb/842694) and I came to the point where it says to delete the server from Sites and Services. However when I clicked delete it wanted me to dcpromo the box first. However I have read you have to uninstall exchange first and then dcpromo it to remove AD. Any ideas?

    Read the article

  • Moving mails from SBS 2008 to SBS 2011

    - by starchx
    we are going to upgrade server from SBS 2008 to a new hardware server with SBS 2011. Due to non-experience in Server Migration (eg, answer file), we have decided to choose Clean Install. We have 12 users so that's not too bad. The most challenge problem is to move over all the emails for each user, some user have 5GB inbox. The one method I know is to login to each user account and export the emails to PST file using Outlook 2007. Then connect to new SBS 2011 and import the PST into new inbox. Do we have any other better/quicker ways? Thanks

    Read the article

  • SBS 2003 to SBS 2011

    - by Steve
    We've migrated SBS 2003 to SBS 2011...so far everything has gone smoothly. We're in the final phase of migrating the last amount of data over. Is there a way I can check to be sure that our old server isn't restarting due to the 21 day grace period? As our 21 days is up on Thursday. Yet it's restarting on its own now...maybe a power supply issue...? Is there any way to extend the 21 days? or roll it back? or does this take a call to MSFT? Very odd...

    Read the article

  • SBS domain name choice

    - by sandymac
    We are about to set up SBS 2011 at my small company < 10 users. My collaborator wants to name the SBS domain "example.local" . I'm of the opinion we should name the SBS domain "corp.example.com" and setup DNS so the "corp" record is a NS record to the SBS server's private IP. FYI: "Example.com" isn't the real domain name and while the website is hosted outside our office, email will be stored on the SBS server in our office after passing though a spam filtering smart host hosted elsewhere too.

    Read the article

  • New SBS 2011 installation (not migration) in an existing 2008 R2 domain

    - by Tong Wang
    My current network setup has two servers: a Windows 2008 R2 with TMG 2010 as edge firewall (TMG server), a second 2008 R2 with DC, DNS and Hyper-V roles (DCDNS server). I was trying to install SBS 2011 as a child partition on DCDNS, first I installed SBS 2011 in English and did the migration successfully. However, later on, I found that I can't change the display language in SBS 2011 once it's installed (but the clients require a different language), so I had to re-install the SBS in a different language. It is during the re-installation that the problem came up: the migration can't be completed with some error message stating "can't access the source server". I re-ran the migration preparation tool, but it didn't make any difference. I wonder if it's because the source server can only be "migrated" once. Since I only need to setup a handful of users and computers, so I decided to do a new install of SBS and picked a different domain name. But I can't get the SBS to connect to LAN: it can't ping other servers, neither can other servers ping the SBS server. I've tried to stop the DC/DNS services on DCDNS and restart SBS, but with no difference. Anyone has idea how to fix this problem?

    Read the article

  • Migrating SBS 2003 to 2011, and hangs when migrating Public Folders

    - by Daniel P
    I've been following the migration guide at http://www.it-book.co.uk/1651/migration-from-sbs-2003-to-sbs-2011-3. The option "Migrate Exchange mailbox and settings" links me to http://technet.microsoft.com/en-us/library/gg563803.aspx When I get to the stage of right-clicking "Move All Replicas", it instantly hangs. I can't see anything specifically in the event viewer at the time this happens. Is this a case of waiting, or is there something more going on here?

    Read the article

  • Migrating 2008 AD to Windows SBS 2011 and Forefront TMG 2010

    - by Tong Wang
    Our company has two physical servers: a Dell R710 with 4 NIC and a Dell R410 with 2 NIC. Right now, we have Windows server 2008 R2 installed on R710 with AD setup to host our domain. I am thinking to install both SBS 2011 and TMG 2010 on the other R410 running on Hyper-V. As I am fairly new to Windows Server technology, I'd like to check with you fellow Windows admins and see what is the proper way to install SBS 2011 and TMG 2010 and how to migrate the 2008 AD. Your advice and help will be highly appreciated.

    Read the article

  • SBS 2008 DNS issues in BPA

    - by evesirim
    I'm gettng constant Critical Issue events in the Small Business Server Best Practices Analyser & resulting SBS Console reports that begin "The DNS client is not configured to point only to the internal IP address of the server.". When I check the DNS Manager, there are two separate IPs listed, one ***.***.***.2 and the other ***.***.***.28. I have checked online after an ipconfig /all and have found the reason for this to be that the second IP is created by DHCP for RAS & VPN purposes. It seems to cause no conflicts of any detrimental result apart from constantly sending me error messages and alerted reports. Does anyone know of a way that I can change settings somewhere so that Windows accepts this second IP, or at least stops alerting me of its prescence? Perhaps a registry hack of some kind...? Many thanks in advance

    Read the article

  • Migrate SBS 2008 with Exchange 2007 to new hardware

    - by MikeT505
    Hello, We have run out of hard disk space on our existing Small Business Server 2008 and simply wish to upgrade both of the hard drives (currently raid 1) - without too much hassle. My main concern is how to copy across the embedded version of Microsoft Exchange 2007. Is there a simple way to copy all the data across and upgrade? Or is it best to backup and do a clean install? - The difficulty is that it's the same server, so we can't replicate mailboxes for exchange. Any hints or tips welcomed!?

    Read the article

  • migrate SharePoint to SBS Server

    - by Eric Lorson
    We have a SharePoint 2003 server and we need to migrate that data to SharePoint 2011 on a SBS server. We cannot use the migration tool because one of the servers is SBS and the other is not. We exported the SharePoint data from the old system, but the import to the SBS SharePoint is failing with very little info on why. I think that there is a schema conflict, but I am not that familiar with SBS and I am not finding the error in the Windows logs. Has anyone had to migrate data from non-SBS system to an SBS system? Or can anyone help me figure out where to look for more info on what is going on?

    Read the article

  • SBS 2011 on different subnet than domain computers

    - by Ravi
    The setup is as follows: SBS 2011 in datacentre on subnet A Domain PCs at another location on subnet B There is a site-to-site VPN. The domain PCs have joined the domain and have the SBS as their primary DNS server. The domain PCs can ping the DC but the problem is that the DC cannot ping any of the remote subnet (subnet B) SBS --Switch -- Router A ------------------- Router B -- Switch -- Domain PCs What is strange is that router A can ping any host on the subnet B. Another host on Subnet A can also ping any host on subnet B. It's only the DC which cannot ping anything to that specific remote subnet B. I did a tracert from the SBS to router B. The packet reaches Router A from the SBS but then it fails. Am I missing some specific settings that needs to be done when SBS is on a different subnet than its member pcs ?

    Read the article

  • Can't seem to setup RICOH to scan to SBS 2008 shared folder

    - by Critter
    Banging my head against any hard surface trying to figure out why I cannot connect the RICOH copier to a shared folder on my SBS 2008. Here's the particulars: New SBS 2008 Server New Network clients running Win XP Pro SP3 New Ricoh multifunction copier Cannot browse network and find SBS server shared folder from Copier Setup SMB to shared folder Authenticate using admin user name and password Copier cannot connect. What am I missing? I have setup numerous copiers to scan to folder in a Windows Server 2003 environment. First time user on SBS 2008. I feel so inadequate!

    Read the article

  • Always a path to the internet even in Windows SBS is off

    - by Mark
    Hello all, is it possible to have a configuration in a Windows 2003 SBS environment where in the event that the SBS box crashed/turned off/ or is being worked on that there can still exist a path to the internet for domain users and visitors to still use? I would like to have the standalone router issue DHCP IPs. The primary DNS would point to the SBS, the secondary wouuld point to the ISP DNS Server. My theory was that if someone was using the internet and the SBS box went down they wouldn't be able to access the network shares but still be able to use the internet. (We are moving everything into the clouds with Google Apps Non-Profit) Does this seem like a reasonable configuration? Or are they're pitfalls that I will fall into? Thanks Mark

    Read the article

  • Unable to install sbs 2008 in DELL POWEREDGE T100 [closed]

    - by Swaminathan Shanmugam
    Still unable to install WIN SBS 2008 in DELL POWEREDGE T100 server and the long post is going on at http://social.technet.microsoft.com/Forums/en-US/winservergen/thread/aa1bc4b0-943e-4ada-8de1-e03161c8fc2c My problem is unable to install sbs 2008 in 500 GB 4k sectors hdd but installation is successful in 512 bytes sector hdd. Anybody please help to solve this issue? Installation of SBS 2008 proceeds ; atlast it is not getting completed with the error message "Windows Setup could not configure Windows on this computer’s hardware"

    Read the article

  • SBS 2003 boot stalls at acpitabl.dat

    - by John
    I have a SBS 2003 server running for 3 year without any problems, and few days ago it freezes during the boot. System is using two 500 Gb drives in RAID1 (Intel Matrix 7.5) After trying to load in safe mode, boot stops on acpitabl.dat. First idea was that there is a problem with RAID altough disk status was OK, and RAID status was Rebuild. I tried to boot with each drive, and one gives me the same problem, and the other drive is failing to load. Took both drives out, and checked it on a different machine. One drive is dead, other is without any problems. Returned the good drive back in SBS 2003 with changed status to Degraded, but the problem is still the same. I also have a clean SBS 2003 copy installed on this drive (previous installation), which loads smooth and quick. So, I believe the main problem is this installed version of SBS 2003. Did not make any hardware changes, did not make any updates (not sure about any automatic windows updates lately). Since there are tons posts about this problem, and no clear solution, I am trying to figure how to repair SBS 2003 installation, since there are some installed programs on this installation which I cannot re-install without additional issues.

    Read the article

  • sbs 2001 essentials rdp cert install package

    - by Crash893
    Im using Microsoft SBS 2011 esentials to allow some of my users to remote into there work machines when they try they get and error that says that the rd gateway can not be trusted I looked up the error on google and confirmed that i need to install the ssl cert on the local machine but the instructions given are for sbs 2011 standard (website here ) but the path given is not in sbs essentials so where can i find the " Install Certificate Package.zip " file in essentials?

    Read the article

  • Virtualize SBS 2003 - P2V vs migrating to new VM

    - by jlehtinen
    I need to virtualize a SBS 2003 server in my work environment. I need some tips on what people think is the best way to proceed. Background: The SBS 2003 server is the primary DC for the domain and also hosts FTP, RRAS(VPN), DNS, and file shares. Exchange is NOT used, neither is SQL server. DHCP is done via a firewall appliance. I have added a Server 2003 VM to the domain and promoted it to the DC role. AD/DNS is replicating here correctly. This was mainly done to provide fault-tolerance to the domain, I was not intending to make this VM the primary DC. I've already asked about buying upgraded licensing for Server 2008/2012 but was refused due to cost. Options: I see (at least) two routes I could take to complete this. From what I've read option 2 is the "preferred" method, but there's a few steps where I'm not clear on what to expect. Option 1.) P2V the primary DC Power off primary DC Power off secondary DC (to prevent USN rollback in case P2V has issue) P2V (cold clone) primary DC Boot new PDC VM Allow new hardware to detect Remove old NIC hardware from device manager Assign old IPs to new virtual NICs Reboot PDC VM, confirm connectivity and no major issues Power on secondary DC, confirm replication Option 2.) Create new VM, transfer roles, remove original DC from domain Create new VM, install SBS 2003 Do I need the original SBS install discs for this? MS migration doc mentions this. Add VM to domain, promote to DC role Does this start 7 day timer where two SBS servers can be in same domain? Set up RRAS on new VM Set up IIS/FTP on new VM Move file shares to new VM Transfer FSMO roles to new VM DC dcpromo original primary DC out of domain

    Read the article

  • SBS 2011 backup

    - by Chris
    I have a freshly installed SBS 2011 server that I need to configure for backup. I tried using the SBS backup configuration tool, but it didn't want to use anything but an external drive. Previously, with our W2K3 servers, I used NTBackup to back up the server to disk and then copied the backup files to a remote server on a regular basis. It doesn't appear this is possible with the built-in backup tools in SBS 2011. Am I missing something? What other options are there that won't cost an arm and a leg?

    Read the article

  • Windows 2003 SBS: no more CAL sold

    - by Gregory MOUSSAT
    I just discovered a hidden unmanaged server into a remote location. This is a Windows 2003 SBS with 5 CAL per device. There is currently 12 computers connected. So I want to buy more CALs. But SBS 2003 CALs are not sold anymore. Neither SBS 2008 CALs, which can be downgraded to 2003. And 2011 CALs can't be downgraded. So no legal solution if we want to stay with 2003. Sort of programmatic obsolescence. We can upgrade the server to 2011. But I'd like to let him as is (I don't "repair" working servers, and this often lead to bigger problems, especially on those non managed servers). Anyone see another solution ?

    Read the article

  • Powershell ActiveDirectory-Module on SBS-2008?

    - by wullxz
    I read plenty of tutorials that describe how to install ADWS (ActiveDirectory Webservices) and Powershell. But I never saw any hint about installing ADWS on a SBS-2008 in order to work with Powershell and ActiveDirectory-module. I know, that I should use the SBS-Console to manage users, but there are tasks where it could be good to use AD as database of users and computers to loop through them (e.g. remote-commands on all workstations, find out user-lastlogon-times etc). Can anybody say, if it's ok (and supported?) to install AD-Powershell-Module and ADWS on a SBS-2008? Thanks

    Read the article

  • Publishing an Excel spreadsheet using Microsoft SBS 2008 to a web page that is viewable by mobile ph

    - by Dave Heath
    I am getting well out of my “superuser” depth here and would love some support. At work we have an Excel workbook (*.xls format circa Office 2003) which maintains our “engineers” timesheet. This handles what events we are doing across the year and how many “work units” it is. As far as a workbook goes, it is fairly simple with just a few =SUM(range) cells and some linked across sheets (12 sheets, one for each month) It is stored on a server, in a folder that provides “management” with full access and “engineers” with read-only access. The workbook itself is read-only for “engineers” and full access for “management”. I think these permissions are controlled through Active Directory. The workbook is protected with a password, assumingly to allow “management” to edit it even if they are working at a terminal logged in as an “engineer”. This protection prevents “engineers” from going to certain cells to see formulae and therefore editing them. The workbook has a macro which saves and closes it ten minutes after opening. This is to stop other “management” from being locked out by any one person who has logged in with editing privileges. I hope this is making sense to someone... :S Now then, we have Microsoft Small Business Server 2008. We have a shiny new web-based login for when we are offsite so we can get to Exchange webmail and our internal site (which uses Sharepoint 3.0). “Management” would like to be able to publish this timesheet automatically after changes (they don’t want to have to do anything different to what they are currently doing) so that using an iPhone “engineers” can check on it while out of the office. I am currently having a look at “Excel Services” for Office 2007 on TechNet but I am not sure if I am running down the right garden path at the moment. < EDIT This seems to suggest that I have to have Sharepoint Server 2007, with no mention of Sharepoint 3.0... ... "MOSS builds on WSS by adding both core features as well as end user web parts" - Wikipedia entry for Microsoft Office SharePoint Server (MOSS) this is not good news... "...and using the ASP.NET APIs, web parts can be written to extend the functionality of WSS." Wikipedia entry for Windows Sharepoint Services. Could this bring back what I need? Is this good news? Do I need to start learning ASP.NET? This link here implies that we need MOSS to do what I want and the bosses say we aint' getting it. http://serverfault.com/questions/20198/what-is-some-cool-things-you-can-do-with-sharepoint-2007/22128#22128 Back to the drawing board. < /EDIT Please could someone suggest some “further reading” for me to help point me in the right direction or to put me back on the right track. Many thanks. I will try to keep this up to date with how I get on.

    Read the article

  • Create Windows SBS 2008 User Account without Email

    - by Mark Henderson
    Just today I've been handed an SBS 2008 server to do some maintenance on. I've never used SBS 2008 before today, so this is a real noob question: Is it possible to create a user account without creating an associated exchange mailbox? I've been asked to create a new user, but not give them an email address. I guess I could just disable their email account in Exchange, but is there a nicer method?

    Read the article

  • Setting up Windows SBS 2008 network on Xen

    - by samyboy
    I'm trying to install a Windows SBS 2008 server in a Xen environment. The OS is booting fine. Unfortunately I can't figure out how to set up the network settings. Dom0 is a Debian Lenny hosting around 10 virtual servers. Here are the settings I'm using in the hosted Windows SBS: IP address: 10.20.0.8 Network mask: 255.255.0.0 Gateway: 10.20.0.1 Note that during the installation stage, Windows set the net mask at 255.255.255.0 without letting me choose. Gross. Windows SBS tells me I have a "limited connection". I can't ping the gateway nor any other IP except localhost and it's own IP (10.20.0.8). Here is the Xen config file: kernel = '/usr/lib/xen-3.2-1/boot/hvmloader' builder = 'hvm' memory = '4096' device_model='/usr/lib/xen-3.2-1/bin/qemu-dm' acpi=1 apic=1 pae=1 vcpus=1 name = 'winexchange' # Disks disk = [ 'phy:/dev/wnghosts/exchange-disk,ioemu:hda,w', 'file:/mnt/freespace/ISO/DVD1_Installation.iso,ioemu:hdc:cdrom,r' ] # Networking vif = [ 'mac=00:16:3E:0A:D0:1B, type=ioemu, bridge=xenbr0'] # video stdvga=0 serial='pty' ne2000=0 # Behaviour boot='c' sdl=0 # VNC vfb = [ 'type=vnc' ] vnc=1 vncdisplay=1 vncunused=1 usbdevice='tablet' This config is working with others Windows XP domU's. I tried to change the ne2000 values with 0 and 1 with no effect. I am far from having good Windows administration skills so I guess I definitely need some help on this case. Thanks.

    Read the article

  • SBS 2011 Essentials and too many new Mac users

    - by Harry Muscle
    We currently have about 15 users on a Windows SBS 2011 Essentials Server. I've just been informed that we plan to bring aboard about 15 more users that will be using Macs. We'll be using a Mac Server to manage the 15 new Macs, however, I'm looking for advice on how to best set this all up. Ideally I would just add the 15 new Mac users to Active Directory and setup the Mac Server to authenticate against AD, unfortunately the SBS 2011 Essentials Server has a limit of 25 users, so adding these new users to AD won't work unless we upgrade the Windows server (which I'd rather avoid since it's a lot of work and a lot of money). That leaves the option of creating user accounts for these 15 Mac users on the Mac Server only. The problem that this creates though is how do I share files been Mac users and Windows users since they are now using different systems for network authentication. Any advice (short of upgrade to SBS Standard) is highly appreciated. Thanks, Harry P.S. We don't run Exchange or anything else on our server ... it's mainly used for file sharing and enforcing security via group policies.

    Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >