Search Results

Search found 2482 results on 100 pages for 'hp elitebook'.

Page 1/100 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • /usr/lib/cups/backend/hp has failed with an HP LaserJet p3005

    - by edtechdev
    Ever since 10.04, I can't print to an HP laserjet p3005. I'm even using an entirely different computer now with a fresh install of 10.10. I've tried with and without the latest hplip. Recently, sometimes I can get it to print a few things, but eventually it always fails (usually when printing a pdf from the document viewer (also doesn't work with adobe pdf reader)). Sometimes it fails so bad the printer gives an error saying it needs to be turned off and on again. I can't seem to find a fix anywhere, I've googled all over the past year and tried every fix I could find. It does say that the /usr/lib/cups/backend/hp has failed. It also doesn't make a difference if I create the printer using hp-setup or ubuntu's own printing control panel. I delete and re-create the printer, no difference eventually. I use the default printer settings or custom settings, no difference. I can print perfectly find to a networked printer at home - an HP officejet 6310. It seems to be networked HP printers at work that I can't print to anymore (except occasionally right after re-installing the printer driver). What's the recommended way to install HP printer drivers and reset or clean out everything from before. Or where are the right logs to read or debug commands to do to find out what may be the real cause of the printing problems?

    Read the article

  • /usr/lib/cups/backend/hp has failed with an HP LaserJet p3005

    - by edtechdev
    Ever since 10.04, I can't print to an HP laserjet p3005. I'm even using an entirely different computer now with a fresh install of 10.10. I've tried with and without the latest hplip. Recently, sometimes I can get it to print a few things, but eventually it always fails (usually when printing a pdf from the document viewer (also doesn't work with adobe pdf reader)). Sometimes it fails so bad the printer gives an error saying it needs to be turned off and on again. I can't seem to find a fix anywhere, I've googled all over the past year and tried every fix I could find. It does say that the /usr/lib/cups/backend/hp has failed. It also doesn't make a difference if I create the printer using hp-setup or ubuntu's own printing control panel. I delete and re-create the printer, no difference eventually. I use the default printer settings or custom settings, no difference. I can print perfectly find to a networked printer at home - an HP officejet 6310. It seems to be networked HP printers at work that I can't print to anymore (except occasionally right after re-installing the printer driver). What's the recommended way to install HP printer drivers and reset or clean out everything from before. Or where are the right logs to read or debug commands to do to find out what may be the real cause of the printing problems?

    Read the article

  • Getting hp-snmp-agents on HP ProLiant DL360 on Lenny working

    - by mark
    After receiving our HP ProLiant DL360 I'd like to integrate the machine into our Munin system and thus enable ProLiant specific information to be exposed via SNMP. I'm running Debian Lenny with kernel 2.6.26-2-vserver-amd64 . I've followed http://downloads.linux.hp.com/SDR/getting_started.html and the HP repository has been added to /etc/apt/sources.list.d/HP-ProLiantSupportPack.list . Setting up Lenny SNMP itself is not a problem, I configure it to have a public v1 community string to read all data and it works. I install hp-snmp-agents and run hpsnmpconfig and it adds additional lines to the top of /etc/snmp/snmpd.conf : dlmod cmaX /usr/lib64/libcmaX64.so snmpd gets restarted. Via lsof I can see that libcmaX64 was loaded and is used by snmpd, put I do not get any additional information out of snmp. I use snmpwalk -v 1 -c public ... and I can see many OIDs but I do not see the new ones I'd expect, most notably temperatures, fan speed and such. The OIDs I'm expecting are e.g. 1.3.6.1.4.1.232.6.2.6.8.1.4.1 , this is from the existing munin plugins from http://exchange.munin-monitoring.org/plugins/snmp__hp_temp/version/1 . snmpd[19007]: cmaX: Parsing shared as a type was unsucessful snmpd[19007]: cmaX: listening for subagents on port 25375 snmpd[19007]: cmaX: subMIB 1 handler has disconnected snmpd[19007]: cmaX: subMIB 2 handler has disconnected snmpd[19007]: cmaX: subMIB 3 handler has disconnected snmpd[19007]: cmaX: subMIB 5 handler has disconnected snmpd[19007]: cmaX: subMIB 6 handler has disconnected snmpd[19007]: cmaX: subMIB 8 handler has disconnected snmpd[19007]: cmaX: subMIB 9 handler has disconnected snmpd[19007]: cmaX: sent ColdStarts on ports 25376 to 25393 snmpd[19007]: cmaX: subMIB 10 handler has disconnected snmpd[19007]: cmaX: subMIB 11 handler has disconnected snmpd[19007]: cmaX: subMIB 14 handler has disconnected snmpd[19007]: cmaX: subMIB 15 handler has disconnected snmpd[19007]: cmaX: subMIB 16 handler has disconnected snmpd[19007]: cmaX: subMIB 21 handler has disconnected snmpd[19007]: cmaX: subMIB 22 handler has disconnected snmpd[19007]: cmaX: subMIB 23 handler has disconnected snmpd[19007]: cmaX: subMIB 1 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 2 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 3 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 5 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 6 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 8 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 9 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 10 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 11 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 14 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 15 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 16 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 21 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 22 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 23 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 18 handler has disconnected snmpd[19007]: cmaX: subMIB 18 will be sent on port 25393 to cpqnicd snmpd[19007]: NET-SNMP version 5.4.1 This doesn't look particular bad for me, it's just informational I guess. I've compared the walking OID output with and without the module and there's no difference in the OID served back at all. Are there any other prerequisites I'm missing? I've also noticed that from the time I installed hp-snmp-agents it adds a lot of additional daemons and that my load suddenly jumps to 1. I've uninstalled the package for now. Is this expected behavior?

    Read the article

  • Ubuntu 14.04:LTS , HPLIP loses USB connection to HP laserjet

    - by Gareth
    This is my first post, so please let me know if i have inadvertanly broken any rules. Problem There seems to be a problem with HPLIP and USB connections in ubuntu 14.04LTS. After upgrading i managed to get the printing to work but today it has broken. Initial Issue (Solved) After upgrading to unbutntu 14.04 LTS my printer lHP LaserJet 1018 stopped printing (code=12) Looking through the Forumsthere are several issues with printitng and HPLIP so I was able to troubleshoot this. The steps I took were : Reran HPdoctor Ran hp-check Un-installed and installed the latest version of HPLIP (3.14.4) Checked the USB connections lsusb and lsusb-v Re-ran hpcheck Removed the printer from HPLIP Re-ran hpcheck Manually configued HPLIP to the printer hp-setup-g <xxx:yyy> And this worked HPLIP was able to see the printer in the USB , test page printed and was happily working for a few weeks. Current Issue Printer Not working However today my wife complains the printer is not working and checking see that although HPLIP has the same error code and did not seem to be able to see the printer although running lsusb could see the printer. Initially thought this may be due to usb given a new bus/device after being turned on and off and went to repeat the steps above at the moment still seeing an error in that the HPLIP is complaining that it cannot see the device **error: Device not found. Please make sure your printer is properly connected and powered-on.** current Observations lsusb output ## Bus 002 Device 007: ID 03f0:4117 Hewlett-Packard LaserJet 1018 sudo hp-check output *> "duan@duan-Lenovo-B550:~$ sudo hp-check [sudo] password for duan: Saving output in log file: /home/duan/hp-check.log HP Linux Imaging and Printing System (ver. 3.14.4) Dependency/Version Check Utility ver. 15.1 Copyright (c) 2001-13 Hewlett-Packard Development Company, LP This software comes with ABSOLUTELY NO WARRANTY. This is free software, and you are welcome to distribute it under certain conditions. See COPYING file for more details. Note: hp-check can be run in three modes: 1. Compile-time check mode (-c or --compile): Use this mode before compiling the HPLIP supplied tarball (.tar.gz or .run) to determine if the proper dependencies are installed to successfully compile HPLIP. Run-time check mode (-r or --run): Use this mode to determine if a distro supplied package (.deb, .rpm, etc) or an already built HPLIP supplied tarball has the proper dependencies installed to successfully run. Both compile- and run-time check mode (-b or --both) (Default): This mode will check both of the above cases (both compile- and run-time dependencies). Full Output output of hp-setup -g 002:007 window box "device not found please make sure your printer is properly connected and powered on" duan@duan-Lenovo-B550:~$ sudo hp-setup -g 002:007 [sudo] password for duan: > HP Linux Imaging and Printing System (ver. 3.14.4) Printer/Fax Setup > Utility ver. 9.0 > > Copyright (c) 2001-13 Hewlett-Packard Development Company, LP This > software comes with ABSOLUTELY NO WARRANTY. This is free software, and > you are welcome to distribute it under certain conditions. See COPYING > file for more details. > > hp-setup[18461]: debug: param=002:007 hp-setup[18461]: debug: > selected_device_name=None Fontconfig error: > "/etc/fonts/conf.d/65-khmer.conf", line 14: out of memory Fontconfig > error: "/etc/fonts/conf.d/65-khmer.conf", line 23: out of memory > Fontconfig error: "/etc/fonts/conf.d/65-khmer.conf", line 32: out of > memory hp-setup[18461]: debug: Sys.argv=['/usr/bin/hp-setup', '-g', > '002:007'] printer_name=None param=002:007 jd_port=1 device_uri=None > remove=False Searching for device... hp-setup[18461]: debug: Trying > USB with bus=002 dev=007... hp-setup[18461]: debug: Not found. > hp-setup[18461]: debug: Trying serial number 002:007 hp-setup[18461]: > debug: Probing bus: usb hp-setup[18461]: debug: Probing bus: par > error: Device not found. Please make sure your printer is properly > connected and powered-on. hp-setup[18461]: debug: Starting GUI loop. .. USB lead Works with the Windows 7 laptop Printer Works with windows 7 laptop Questions Is this a Bug with HPLIP or an issue with laptop/printer? Supplementary question if it is a bug what information is needed and where should it be sent ? Any suggestions on how to get the printer to work correctly with Ubuntu 14.04LTS/HPLIP 13.4.3 so that it stays working ?

    Read the article

  • On checking kernel parms HP-UX & Oracle 10.2

    - by [email protected]
    Hi,Just did this little script for a customer wanting to investigate if the kernel parameters of their HP-UX machines fits or not the Oracle 10.2 specifications ( looks like someone checked the "User Verified" at database installation time on some prerequisites)Just want to share ( its in Spanish)Hope it helps!--L Normal 0 21 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} ### ### check_kernel_parms.sh ### ### ### ###    NAME ###      check_kernel_parms.sh ### ###    DESCRIPTION ###      Comprueba los parametros de kernel ### ###    NOTES ###     Valido para versiones de SO HP-UX y Oracle 10.2 ###     ### ###    MODIFIED   (MM/DD/YY) ###    lvelasco    05/20/10 - Creacion     V_DATE=`/usr/bin/date +%Y%m%d_%H%M%S` if [ "${1}" != 'sin_traza' ]; then   V_FICHERO_LOG=`dirname $0`/`basename $0`.${V_DATE}.log   exec 4>&1   tee ${V_FICHERO_LOG} >&4 |&   exec 1>&p 2>&1 fi   echo "${V_DATE}- check_params.sh *******************************************" echo "Comenzado ejecucion de chequeo de parametros de kernel en maquina `hostname`" echo "****************************************************************************"   UX_VERS=`uname -a | awk '{print $3}'` KCTUNE=/usr/sbin/kctune MEM_TOTAL_MB=`./check_mem` <-- This should return the physical mem of the machine on bytes MEM_TOTAL=$((MEM_TOTAL_MB*1024))     NPROC=$(${KCTUNE} | grep nproc | grep -v '(nproc' | grep -v *nproc | awk '{print $2}') if [ ${NPROC} -lt 4096 ] then        echo "[FAILED] Information: El parametro nproc con valor actual ${NPROC} debe tener una valor superior a 4096" else        echo "[OK] Information: El parametro nproc con valor actual ${NPROC} debe tener una valor superior a 4096" fi     KSI_ALLOC_MAX_T=$(${KCTUNE} | grep ksi_alloc | awk '{print $2}') KSI_ALLOC_MAX=$((NPROC*8)) if [ ${KSI_ALLOC_MAX_T} -lt ${KSI_ALLOC_MAX} ] then        echo "[FAILED] Information: El parametro ksi_alloc_max con valor actual ${KSI_ALLOC_MAX_T} debe tener una valor superior a ${KSI_ALLOC_MAX}" else        echo "[OK] Information: El parametro ksi_alloc_max con valor actual ${KSI_ALLOC_MAX_T} debe tener una valor superior a ${KSI_ALLOC_MAX}" fi       EXECUTABLE_STACK=$(${KCTUNE} | grep executable_stack | awk '{print $2}') if [ ${EXECUTABLE_STACK} -ne 0 ] then        echo "[FAILED] Information: El parametro executable_stack con valor actual ${EXECUTABLE_STACK} debe tener una valor igual a 0" else        echo "[OK] Information: El parametro executable_stack con valor actual ${EXECUTABLE_STACK} debe tener una valor igual a 0" fi       MAX_THREAD_PROC=$(${KCTUNE} | grep max_thread_proc | awk '{print $2}') if [ ${MAX_THREAD_PROC} -lt 1024 ] then        echo "[FAILED] Information: El parametro max_thread_proc con valor actual ${MAX_THREAD_PROC} debe tener una valor superior a 1024" else        echo "[OK] Information: El parametro max_thread_proc con valor actual ${MAX_THREAD_PROC} debe tener una valor superior a 1024" fi     MAXDSIZ=$(${KCTUNE} | grep 'maxdsiz ' | awk '{print $2}') if [ ${MAXDSIZ} -lt 1073741824 ] then        echo "[FAILED] Information: El parametro maxdsiz con valor actual ${MAXDSIZ} debe tener una valor superior a 1073741824" else        echo "[OK] Information: El parametro maxdsiz con valor actual ${MAXDSIZ} debe tener una valor superior a 1073741824" fi     MAXDSIZ_64BIT=$(${KCTUNE} | grep maxdsiz_64bit | awk '{print $2}') if [ ${MAXDSIZ} -lt 2147483648 ] then        echo "[FAILED] Information: El parametro maxdsiz_64bit con valor actual ${MAXDSIZ_64BIT} debe tener una valor superior a 2147483648" else        echo "[OK] Information: El parametro maxdsiz_64bit con valor actual ${MAXDSIZ_64BIT} debe tener una valor superior a 2147483648" fi   MAXSSIZ=$(${KCTUNE} | grep 'maxssiz ' | awk '{print $2}') if [ ${MAXSSIZ} -lt 134217728 ] then        echo "[FAILED] Information: El parametro maxssiz con valor actual ${MAXSSIZ} debe tener una valor superior a 134217728" else        echo "[OK] Information: El parametro maxssiz con valor actual ${MAXSSIZ} debe tener una valor superior a 134217728" fi     MAXSSIZ_64BIT=$(${KCTUNE} | grep maxssiz_64bit | awk '{print $2}') if [ ${MAXSSIZ} -lt 1073741824 ] then        echo "[FAILED] Information: El parametro maxssiz_64bit con valor actual ${MAXSSIZ} debe tener una valor superior a 1073741824" else        echo "[OK] Information: El parametro maxssiz_64bit con valor actual ${MAXSSIZ} debe tener una valor superior a 1073741824" fi     MAXUPRC_T=$(${KCTUNE} | grep maxuprc | awk '{print $2}') MAXUPRC=$(((NPROC*9)/10)) if [ ${MAXUPRC_T} -lt ${MAXUPRC} ] then        echo "[FAILED] Information: El parametro maxuprc con valor actual ${MAXUPRC_T} debe tener una valor superior a ${MAXUPRC}" else        echo "[OK] Information: El parametro maxuprc con valor actual ${MAXUPRC_T} debe tener una valor superior a ${MAXUPRC}" fi   MSGMNI=$(${KCTUNE} | grep msgmni | awk '{print $2}') if [ ${MSGMNI} -lt ${NPROC} ] then        echo "[FAILED] Information: El parametro msgni con valor actual ${MSGMNI} debe tener una valor superior a ${NPROC}" else        echo "[OK] Information: El parametro msgni con valor actual ${MSGMNI} debe tener una valor superior a ${NPROC}" fi     if [ ${UX_VERS} = "B.11.23" ] then        MSGSEG=$(${KCTUNE} | grep msgseg | awk '{print $2}')        if [ ${MSGSEG} -lt 32767 ]        then        echo "[FAILED] Information: El parametro msgseg con valor actual ${MSGSEG} debe tener una valor superior a 32767"        else        echo "[OK] Information: El parametro msgseg con valor actual ${MSGSEG} debe tener una valor superior a 32767"        fi fi   MSGTQL=$(${KCTUNE} | grep msgtql | awk '{print $2}') if [ ${MSGTQL} -lt ${NPROC} ] then        echo "[FAILED] Information: El parametro msgtql con valor actual ${MSGTQL} debe tener una valor superior a ${NPROC}" else        echo "[OK] Information: El parametro msgtql con valor actual ${MSGTQL} debe tener una valor superior a ${NPROC}" fi       if [ ${UX_VERS} = "B.11.23" ] then        NFILE_T=$(${KCTUNE} | grep nfile | awk '{print $2}')        NFILE=$((15*NPROC+2048))        if [ ${NFILE_T} -lt ${NFILE} ]        then        echo "[FAILED] Information: El parametro nfile con valor actual ${NFILE_T} debe tener una valor superior a ${NFILE}"        else        echo "[OK] Information: El parametro nfile con valor actual ${NFILE_T} debe tener una valor superior a ${NFILE}"        fi fi     NFLOCKS=$(${KCTUNE} | grep nflocks | awk '{print $2}') if [ ${NFLOCKS} -lt ${NPROC} ] then        echo "[FAILED] Information: El parametro nflocks con valor actual ${NFLOCKS} debe tener una valor superior a ${NPROC}" else        echo "[OK] Information: El parametro nflocks con valor actual ${NFLOCKS} debe tener una valor superior a ${NPROC}" fi   NINODE_T=$(${KCTUNE} | grep ninode | grep -v vx | awk '{print $2}') NINODE=$((8*NPROC+2048)) if [ ${NINODE_T} -lt ${NINODE} ] then        echo "[FAILED] Information: El parametro ninode con valor actual ${NINODE_T} debe tener una valor superior a ${NINODE}" else        echo "[OK] Information: El parametro ninode con valor actual ${NINODE_T} debe tener una valor superior a ${NINODE}" fi     NCSIZE_T=$(${KCTUNE} | grep ncsize | awk '{print $2}') NCSIZE=$((NINODE+1024)) if [ ${NCSIZE_T} -lt ${NCSIZE} ] then        echo "[FAILED] Information: El parametro ncsize con valor actual ${NCSIZE_T} debe tener una valor superior a ${NCSIZE}" else        echo "[OK] Information: El parametro ncsize con valor actual ${NCSIZE_T} debe tener una valor superior a ${NCSIZE}" fi     if [ ${UX_VERS} = "B.11.23" ] then        MSGMAP_T=$(${KCTUNE} | grep msgmap | awk '{print $2}')        MSGMAP=$((MSGTQL+2))        if [ ${MSGMAP_T} -lt ${MSGMAP} ]        then        echo "[FAILED] Information: El parametro msgmap con valor actual ${MSGMAP_T} debe tener una valor superior a ${MSGMAP}"        else        echo "[OK] Information: El parametro msgmap con valor actual ${MSGMAP_T} debe tener una valor superior a ${MSGMAP}"        fi fi   NKTHREAD_T=$(${KCTUNE} | grep nkthread | awk '{print $2}') NKTHREAD=$((((NPROC*7)/4)+16)) if [ ${NKTHREAD_T} -lt ${NKTHREAD} ] then        echo "[FAILED] Information: El parametro nkthread con valor actual ${NKTHREAD_T} debe tener una valor superior a ${NKTHREAD}" else        echo "[OK] Information: El parametro nkthread con valor actual ${NKTHREAD_T} debe tener una valor superior a ${NKTHREAD}" fi     SEMMNI=$(${KCTUNE} | grep semmni | grep -v '(semm' | awk '{print $2}') if [ ${SEMMNI} -lt ${NPROC} ] then        echo "[FAILED] Information: El parametro semmni con valor actual ${SEMMNI} debe tener una valor superior a ${NPROC}" else        echo "[OK] Information: El parametro semmni con valor actual ${SEMMNI} debe tener una valor superior a ${NPROC}" fi     SEMMNS_T=$(${KCTUNE} | grep semmns | awk '{print $2}') SEMMNS=$((SEMMNI+2)) if [ ${SEMMNS_T} -lt ${SEMMNI} ] then        echo "[FAILED] Information: El parametro semmns con valor actual ${SEMMNS_T} debe tener una valor superior a ${SEMMNS}" else        echo "[OK] Information: El parametro semmns con valor actual ${SEMMNS_T} debe tener una valor superior a ${SEMMNS}" fi   SEMMNU_T=$(${KCTUNE} | grep semmnu | awk '{print $2}') SEMMNU=$((NPROC-4)) if [ ${SEMMNU_T} -lt ${SEMMNU} ] then        echo "[FAILED] Information: El parametro semmnu con valor actual ${SEMMNU_T} debe tener una valor superior a ${SEMMNU}" else        echo "[OK] Information: El parametro semmnu con valor actual ${SEMMNU_T} debe tener una valor superior a ${SEMMNU}" fi     if [ ${UX_VERS} = "B.11.23" ] then        SEMVMX=$(${KCTUNE} | grep msgseg | awk '{print $2}')        if [ ${SEMVMX} -lt 32767 ]        then        echo "[FAILED] Information: El parametro semvmx con valor actual ${SEMVMX} debe tener una valor superior a 32767"        else        echo "[OK] Information: El parametro semvmx con valor actual ${SEMVMX} debe tener una valor superior a 32767"        fi fi     SHMMNI=$(${KCTUNE} | grep shmmni | awk '{print $2}') if [ ${SHMMNI} -lt 512 ] then        echo "[FAILED] Information: El parametro shmmni con valor actual ${SHMMNI} debe tener una valor superior a 512" else        echo "[OK] Information: El parametro shmmni con valor actual ${SHMMNI} debe tener una valor superior a 512" fi     SHMSEG=$(${KCTUNE} | grep shmseg | awk '{print $2}') if [ ${SHMSEG} -lt 120 ] then        echo "[FAILED] Information: El parametro shmseg con valor actual ${SHMSEG} debe tener una valor superior a 120" else        echo "[OK] Information: El parametro shmseg con valor actual ${SHMSEG} debe tener una valor superior a 120" fi   VPS_CEILING=$(${KCTUNE} | grep vps_ceiling | awk '{print $2}') if [ ${VPS_CEILING} -lt 64 ] then        echo "[FAILED] Information: El parametro vps_ceiling con valor actual ${VPS_CEILING} debe tener una valor superior a 64" else        echo "[OK] Information: El parametro vps_ceiling con valor actual ${VPS_CEILING} debe tener una valor superior a 64" fi   SHMMAX=$(${KCTUNE} | grep shmmax | awk '{print $2}') if [ ${SHMMAX} -lt ${MEM_TOTAL} ] then         echo "[FAILED] Information: El parametro shmmax con valor actual ${SHMMAX} debe tener una valor superior a ${MEM_TOTAL}" else         echo "[OK] Information: El parametro shmmax con valor actual ${SHMMAX} debe tener una valor superior a ${MEM_TOTAL}" fi exit 0  

    Read the article

  • HP DL380 G7 Disk swap to a HP DL380 G6

    - by rnuno
    The HP DL380 G7 has 3 SAS disks in RAID 5 configuration. I need to change that server to another task and instead of make a clean install on the HP DL380 G6 can i just swap the 3 disks from HP DL380 G7 to the HP DL380 G6? I expect some driver issues maybe on the OS itself because the processor is different. They both use Smart Array P410i, if i power down the machines swap the disk by the same order will the RAID 5 configuration remain and the OS will boot?

    Read the article

  • Display Driver stopped responding and recovered successfully- Blue Screen - HP Elite Book

    - by Fahad Saleem
    I have HP ELiteBook , this problem has become a routine headache for me (after every 20, 25 minutes_ - While using, suddenly everything hangs and black out goes around and then a message pop at the task bar below that display driver stopped ...and successfully recovered but the hangs and black screen continues and then the Blue Death Screen comes" and then i have no other option but to restart Is this a driver problem ? Hardware problem ? what should I do Please be specific , no stories and theories

    Read the article

  • HP SmartArray P212 with non HP disks, Insight Diagnostics error

    - by yonatan
    I have an ML110 G6 with a SmartArray P212 and two Seagate (non-HP) SAS disks in Raid 1. When I ran HP Insight Diagnostics I got some errors related to S.M.A.R.T. error testing and I would like to confirm that this is due to the controller not being able to query the drives as they are non-HP. I believe that the drives are not failing, but I want to be sure. Please have a look at these screenshots I took from the Insight Diagnostics report:

    Read the article

  • How to get hp printer to select correct trays on samba shared printer

    - by dgermann
    My first post here. Clean install of 12.04.1. Previously 10.04. Have been running a p2035n printer without problem. Now, no matter what paper tray I select it prints to the top "by-pass" feeder--not the lower main tray. And when I select to print to manual feed, it does not wait for me to put in paper (like it used to), but prints immediately. The printer is on a samba share and is physically plugged into a WinXP machine. Its uri is smb:///computername/p2035n. I have tried several of the offered drivers for this hp machine, and even tried generic-laser. Same result on all. Here are some other things I have tried (losing 2-3 hours of my time!): hp-check -t reports “error: User needs to be member of group 'lp' to enable print, scan & fax. ” and “warning: Printer is not HPLIP installed. Printers must use the hp: or hpfax: CUPS backend to function in HPLIP.” needed to download HPLIP 3.12.11 followed http://hplipopensource.com/hplip-web/install/install/index.html sh hplip-3.12.11-run says that before setup logout and then on login run hp-setup hp-setup could not find the printer ran hp-check -t again, found I was not in group lp ran hp-check --fix and it fixed that problem, asks for reboot rebooted after running update manager (new kernel) and hp-check -t shows no errors this time all the tray selections end up on the bypass tray hp-setup still cannot find the printer So is there a way to make this work? Thanks! :- Doug.

    Read the article

  • HP PDX Laptop and blu-ray region, HP MediaSmart problem

    - by Lasse V. Karlsen
    I have a laptop here, a HP HDX 16 EO1000 with a Blu-Ray drive. Installed on the machine is a software package called HP MediaSmart, which presumably can play Blu-Ray movies. However, when inserting a BD disk and starting HP MediaSmart, it comes up with a warning screen and the following message: This disc has been coded for Region B only and will not play in this machine. Please eject this disc and play on a Region B player. The question is, can we change this region? The machine is in europe, which is the B-region, but apparently the drive, or software, or both, is set to some other region. I don't even know where to find the current setting so if anyone knows, please post an answer with some information of where to look.

    Read the article

  • Download HP Power Protector for ESXi

    - by Mark Henderson
    The HP PowerProtector user guide states that to install the HP PowerProtector client on an ESXi Host: Download the latest version of HPPP from the HP website (http://www.hp.com/go/rackandpower). The ESXi Server is automatically detected, and a shutdown command script is generated. However in typical HP fashion, after clicking through no less than 6 different links to get to the downloads page, I am presented with: http://h18004.www1.hp.com/products/servers/proliantstorage/power-protection/software/power-protector/pp-dl.html HP Power Protector (HPPP) - Windows HP Power Protector (HPPP) - Linux x86 HP Power Protector (HPPP) - Linux x64 HP Power Protector (HPPP) - Linux IA64 HP Power Protector (HPPP) - HPUX The Linux packages contain an RPM and in no way resemble what is in the HP documentation. None of these are labelled for ESXi. Does anyone know where or how to get the HP Power Protector ESXi client installed?

    Read the article

  • HP EliteBook 8440p screen flickers after blank screen (nvidia)

    - by fliegenderfrosch
    When my screen turns blank after 10 min or after locking the screen and I begin using the laptop again, the screen is flickering. It looks as if every second line of pixels is blinking and the flickering is mainly present in the upper part of the screen. I am using Ubuntu 12.04 with the latest binary Nvidia drivers (current-updates). lshw | grep VGA tells me: 01:00.0 VGA compatible controller: NVIDIA Corporation GT218 [NVS 3100M] (rev a2) The problem doesn’t occur after sleeping or on an external display. I used Kubuntu 11.10 before, where the problem didn’t occur either. Is there anything I can do except waiting for new drivers?

    Read the article

  • HP EliteBook 8440P - USB ports stop working on docking station

    - by r0ca
    I have a HP Elitebook 8440P running Windows XP Pro SP3. I installed it on my docking station and everything went smooth for a while. Last week, my mouse and any other USB devices stoped working sudenly... It was working fine on my laptop itself but nothing on my docking station. LCD attached monitor works and same for LAN and PS2 keyboard. I updated the BIOS, Chipset, Video Drivers, also changed my docking station by a brand new one but the problem still comes back. I also noticed something in Device Manager... A Generic USB Root Hub has an error on it, a Yellow/Orange exclamation mark. I tried to update that driver but no luck. Windows is unable to process it. This seems to be the problem but can't fix it. I may only re-image my laptop but for me, I need to avoid that since I have so many apps installed on it. If anybody has any advice, I'll take it!

    Read the article

  • CUPS: HP printer DNS url

    - by wintersolutions
    The URL for my printer generated by hp-makeuri looks like this: hp:/net/Officejet_6500_E710n-z?ip=192.168.178.30 But the printer is on a dhcp enabled wifi network and so its IP-address does and could change. On the other hand my wifi router seems smart enough to have some sort of DNS: $ ping hp-6500a PING hp-6500a.fritz.box (192.168.178.30) 56(84) bytes of data. 64 bytes from hp-6500a.fritz.box (192.168.178.30): icmp_req=1 ttl=255 time=11.3 ms I tried to use the hostname in the CUPS URL/DeviceUID but it failed, any suggestions if this is possible and the correct format?

    Read the article

  • /usr/lib/cups/backend/hp has failed

    - by edtechdev
    Ever since 10.04, I can't print to an HP laserjet p3005. I'm even using an entirely different computer now with a fresh install of 10.10. I've tried with and without the latest hplip. Recently, sometimes I can get it to print a few things, but eventually it always fails (usually when printing a pdf from the document viewer (also doesn't work with adobe pdf reader)). Sometimes it fails so bad the printer gives an error saying it needs to be turned off and on again. I can't seem to find a fix anywhere, I've googled all over the past year and tried every fix I could find. It does say that the /usr/lib/cups/backend/hp has failed. It also doesn't make a difference if I create the printer using hp-setup or ubuntu's own printing control panel. I delete and re-create the printer, no difference eventually. I use the default printer settings or custom settings, no difference. I can print perfectly find to a networked printer at home - an HP officejet 6310. It seems to be networked HP printers at work that I can't print to anymore (except occasionally right after re-installing the printer driver). What's the recommended way to install HP printer drivers and reset or clean out everything from before. Or where are the right logs to read or debug commands to do to find out what may be the real cause of the printing problems?

    Read the article

  • Need HP recovery partition info

    - by ggambett
    I'm configuring a new HP Pavillion DV4 with a 320 GB disk. I made the recovery DVDs, then did a couple other things (including deleting the recovery partition), and finally decided to restore the system. Unfortunately, the recovery process fails; the three DVDs are read (the recovery program says "Reformatting the Windows partition" and "Copying files required to restore the hard drive") but after it finishes reading the 3rd, and the progress bar reaches 100%, it fails with error 0xe0f00013 - Googling it didn't return anything at all. I'm afraid this may be because I deleted the partitions. So, I'm kindly asking for one of the following, in order of preference, from a HP Pavillion DV4 with a 320 GB hard disk or a similar enough one : 1) A dump of the MBR 2) The type and size of all the partitions in a "new" system so I can try to make a partition table resembling the original one. BTW, I thought the recovery DVDs were supposed to work even if the entire disk was wiped - isn't that the case? Thanks!

    Read the article

  • HP Printer scrolls "printing" forever - but nothing happens

    - by brett80
    I got a used HP Officejet 7130 all-in-one printer. I tried printing a text document, and it shows up in the queue (and says "printing"), and the printer display says "Printing" "Press Cancel to cancel job." - and it cyles that text forever, but nothing ever happens (after a couple of initial quiet noises.) I tried to print a test page from the printer, and I get the same "printing" message. I checked the hp website, and this problem is not on their list. (They are expecting a queue problem, error message, etc.) I did initially get a message that it needs new ink cartridges, but I pressed to get past that. It's supposed to try to print anyway. I don't want to buy ink cartridges for a printer that is broken. When I press it cancels correctly.

    Read the article

  • How to enable printer settings over Jetdirect on HP 4100N

    - by zsero
    I have a HP 4100N printer and I am using it over network. Previously I was able to access the printer settings over internet, but now the only thing visible is Device Info and Networking. I can connect to the web server and I can set all the network related settings, but that's not what I want. There should be a supplies, config, print info, etc. page, what are not visible now. Can you tell me what setting should I set to enable this printer config page on the webserver? The printer is a HP 4100N and the network card is J4169A (Jetdirect 610n).

    Read the article

  • HP LaserJet 2550 has a carousel motor error

    - by Arlen Beiler
    I have a LaserJet 2550, and it's worked pretty good for a long time (except for some slowness a while back, spooling I think), but just recently it suddenly quit working. We moved this summer, but left it at our other place, and just recently when my Dad went over there to try to print something out, it didn't work. When you turn it on, you hear the fan give a false start (basically a quick pulse), and the carousel goes through its usual thing. Then it starts up in earnest like it's getting ready to print something. All of a sudden it just stops. Everything stops, and the three lower lights are steady. When I push the Go button, the Go light (bottom of the 3) turns off, but the other two stay on. I looked it up on the HP website and it says it is a carousel motor problem. I called HP, but they said it is out of warranty. I've opened the cover and held the switch with a screw driver so I could watch it, and it goes through its thing like I described (doesn't seem to make a difference whether the imaging drum is in or not), then when it stops it kind of seems to jump back a little bit (the carousel). I hope this all makes sense (I know you like details), and hopefully you also know what to do to fix it. Thanks.

    Read the article

  • HP UX can not boot from Ignite Tape

    - by Spirit
    We have hp rp2470 server running hp-ux 11.00, with LVM mirroring. As for redundancy we have second rp2470 same hw (same two processors, same ram, same two hdd’s, same number of lan cards). I want to clone first one to the second. For that purpose I am making ignite tape with the following command: make_tape_recovery -x inc_entire=vg00 Ignite tape finishes without problems. When I boot second server from this ignate tape, server is starting to boot, and ignite restore finishes without any errors, only few notes, which are normal. However vmunix is not booting and when restore finishes, it boot to ISL prompt. From this I cannot boot /stand/vmunix. I tried to run recovery shell but no success. When recovery shell ask to do frecover to restore critical files, then I receive error: frecover(5405): unable to open /dev/rmt/0m At first I thought that the problem might be in the difference of the firmware version of the servers: fw version of production server is: Firmware Version 43.50 and fw version of backup server is: Firmware Version 42.19 So i did a fw upgrade of my backup server so that both servers are v43.50, and tried a recovery but again cant boot the system. Next I did another archive tape with -I (Interactive) flag: make_tape_recovery -I -x inc_entire=vg00 and tried recovery with it, again no good. I cannot find any error or warnings on ignite log, and I cannot boot hpux. I am only on ISL prompt. This is what i've noticed on the gsp logs: ************* SYSTEM ALERT ************** SYSTEM NAME: mcnfwim1 DATE: 07/27/2003 TIME: 10:18:49 ALERT LEVEL: 6 = Boot possible, pending failure - action required REASON FOR ALERT SOURCE: 8 = I/O SOURCE DETAIL: 6 = disk SOURCE ID: 0 PROBLEM DETAIL: 0 = no problem detail LEDs: RUN ATTENTION FAULT REMOTE POWER FLASH OFF ON ON ON LED State: Boot Failed. Running non-OS code. Check Chassis and Console Logs for error messages. 0x00000060860010B0 00000000 00000000 - type 0 = Data Field Unused 0x58000860860010B0 00006706 1B0A1231 - type 11 = Timestamp 07/27/2003 10:18:49 And another gsp log: Log Entry # 3 : SYSTEM NAME: mcnfwim1 DATE: 07/27/2003 TIME: 10:12:20 ALERT LEVEL: 6 = Boot possible, pending failure - action required SOURCE: 8 = I/O SOURCE DETAIL: 6 = disk SOURCE ID: 0 PROBLEM DETAIL: 0 = no problem detail CALLER ACTIVITY: 1 = test STATUS: 0 CALLER SUBACTIVITY: 0B = implementation dependent REPORTING ENTITY TYPE: 0 = system firmware REPORTING ENTITY ID: 00 0x00000060860010B0 00000000 00000000 type 0 = Data Field Unused 0x58000860860010B0 00006706 1B0A0C14 type 11 = Timestamp 07/27/2003 10:12:20 Type CR for next entry, - CR for previous entry, Q CR to quit. Please note that I can not change anything on the production server. I can only make changes to the backup server. Any help is appreciated.

    Read the article

  • HP pavilion dv4 1413la

    - by Pablo Bastidas
    I had Ubuntu 10.10 in my Laptop Hp Pavilion dv4 1413la one year ago, I bought a Lenovo and I gave my wife the HP. She had Windows 7 but she said me that I intalled Ubuntu 11.11. I installed ubuntu 11.11 in the HP but i had problems. It freezing frecuently and i don't know What happen The touch mouse work for a moment an after doesn't work y kill genome-session and work again Please help me. PD: I don't speak English, I speak Spanish, I was trying, excuse me if I write bad.

    Read the article

  • HP Pavilion dv7 dual boot with ubuntu and original win7 issues

    - by Neasy11
    I just bought a hp dv7 and I want to dual boot it with the win7 it came with and ubuntu 12.04.1. I shrunk the C partition to make room for the ubuntu one then downloaded an burnt the iso. Next I booted from the cd and followed the simple instructions until I got to the page of the install to choose the partition where all choices were greyed out and the table was completely blank and the drop down only had one choice. After researching this I found that a main problem might be that I can only have 4 primary partitions and the computer was shipped with the 4 already (system,C,recovery,hp tools). I guess my question is what is the best way to go about completing this dual boot? I have read to delete the hp tools partition or combine it with another, I just want a step by step of how to dual boot this computer, I have done plenty of computers in the past but never ran into these issues that come with an HP (should have got a dell lol)!

    Read the article

  • Linux on HP Envy

    - by Oscar Godson
    OK, the Ubuntu forums aren't helping and I thought maybe you guys here could help. First off, does anyone know the best flavor of Linux to use on an HP Envy? what has the best support out of the box? If not, does anyone know how the hell to get the following to work on Ubuntu 10.04: The touchpad to work at all? Right now, right clicking doesnt work at at all, and left clicks dont work while you have another finger on the pad at all. It jumps all over. ALSO, the multi-touch isn't clickable, but it's for sure a multi-touch touchpad. Works in W7 and can do things like a MBP in W7 The computer feels like it's on fire... i think im missing some driver. Seems odd that the random meta keys like calc, email, brightness, right click, etc work, but not the touchpad? The video card seems fine, but i haven't tested compiz fully yet... Thanks so much to anyone who helps. i want to get back to linux after a couple years on Mac. :)

    Read the article

  • Integrating HP Systems Insight Manager into an existing environment

    - by ewwhite
    I'm working with an environment that spans multiple data centers/sites and consists primarily of HP ProLiant servers (G5-G7) running Linux. The mix is 30% RHEL/CentOS, the rest are Gentoo :(. I also have a few dozen virtual machines running back-office and Windows servers on VMWare ESX hosts. I run OpenNMS to pull SNMP data from the various server nodes and networking devices. While OpenNMS works wonderfully for up/down, thresholds and notifications, it's native handling of traps is a little rough and the graphs are not particularly pretty. I use Orca/RRD graphs for performance trending and nice graphs. I'm tasked with inventorying the environment and wanted to come up with a clean way to organize server information. Since my environment is mostly HP, I've been playing with HP Systems Insight Manager as a way to extract server data and to deploy HP health/monitoring packages and firmware. The Gentoo systems eventually have to be converted to CentOS, so getting a quick assessment of what hardware is where would be great. Although I've read through a few hundred pages of HP manuals, I'm having a difficult time understanding how to get HP SIM to do what I want, though. My main problems are: I have about 40 subnets to deal with; 98% connected with private lines to facilities across the globe. I don't want to initiate an HP SIM discovery only to pull back every piece of intermediate networking hardware and equipment from all of the locations. I'd like this to focus on the servers. I have OpenNMS configured to accept traps. I don't want HP SIM to duplicate that effort. It seems like the built-in software deployment tool wants to overwrite the trapsink parameters for the systems it encounters during discovery. I have about 10 administrative username/password combinations in use across this infrastructure. Is there a more efficient way to get HP SIM to do the discovery or break discovery into manageable chunks? In terms of general workflow, do people typically install the HP Management Agents during the initial OS deployment (e.g. kickstart post script) or afterwards from HP SIM? Is HP SIM too thick/fat to be an inventory tool? I can't tell if it's meant to be used standalone or alongside other monitoring products. Since the majority of the systems I'm trying to track are those running Gentoo (in order to plan the move to CentOS), is there any way for HP SIM to extract system model information from them ( like dmidecode)? I have systems here where I may have an SSH key established, but not direct user or login access. Is there a way for me to import an SSH private/public key pair into HP SIM to reach out to the servers that can't accept standard credentials? There are a handful of sites where I have inconsistent access or have a double-NAT situation. I may be able to poke a server, but it may not be able to find its way back to the management system. Is there a workaround for this? The certificate configuration for HP SIM seems complicated. What is the preferred setup for trust between systems? I'd also appreciate any notes or recommendations to using this product. Or if there's a better way to do this, I'd like to know.

    Read the article

  • HP Compaq 2510p wireless disabled by hardware switch

    - by mylovelyhorse
    I have an HP Compaq 2510p laptop running ubuntu 12.04 LTS. ubuntu reports that wireless is disabled by means of a hardware switch. There is a 'soft-key' button on the laptop to control the physical wireless hardware but this does not respond. There is no other button, slider, (fn)+ combination to control the physical wireless hardware. There is no BIOS function to disable wireless (and on XP - previous OS - wireless functioned fine). mike@ubuntu:~$ rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no Running rfkill unblock all doesn't change things and I can see no way to change use from 0: to 1: (if that's even possible - or desirable - in the first place). I have checked for additional drivers and the Broadcom proprietary wireless driver is already installed and has a green light. Essentially, I believe I need to make the HP 'soft-keys' work - or at least the wireless card toggle. Advice gratefully received. Cheers M

    Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >