Search Results

Search found 963 results on 39 pages for 'nic hubbard'.

Page 1/39 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • My laptop can not access internet after setup bridge with wired NIC and wireless NIC

    - by Victor S
    I setup a bridge using wired NIC and wireless NIC in order to make wireless NIC as a Wi-Fi AP to share wired internet access, after setup successfully, the Wi-Fi AP works as my expectation, but my laptop can not access internet, please give me a hand. Thanks. My hostapd.conf $ cat hostapd.conf interface=wlan0 bridge=br0 driver=nl80211 ssid=myAP hw_mode=g channel=11 dtim_period=1 rts_threshold=2347 fragm_threshold=2346 macaddr_acl=0 auth_algs=3 ieee80211n=0 wpa=3 wpa_passphrase=PassWord wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP Setup steps: $ sudo killall hostapd hostapd: no process found $ sudo hostapd -B hostapd.conf Configuration file: hostapd.conf Using interface wlan0 with hwaddr 00:26:5e:e8:4f:8e and ssid 'myAP' $ sudo brctl addbr br0 device br0 already exists; can't create bridge with the same name $ sudo ifconfig eth0 0.0.0.0 up $ sudo ifconfig wlan0 0.0.0.0 up $ sudo brctl addif br0 eth0 $ sudo brctl addif br0 wlan0 device wlan0 is already a member of a bridge; can't enslave it to bridge br0. $ sudo ifconfig br0 192.168.1.110 netmask 255.255.255.0 $ sudo route add default gw 192.168.1.1

    Read the article

  • MAC addresses on dual-NIC mainboards

    - by Tom O'Connor
    Here's a weird problem. We've got a number of devices with dual-NIC mainboards. Some are Realtek NICs, which suck. Some are Intel e1000s, which don't. I've just noticed on 2 machines, one is an Intel NIC, one is a Realtek, that when I put the MAC address of one machine into the dhcpd.conf file on our DHCP server to get it to PXE boot the machine into a rebuild environment, initially everything is fine. The server gets a DHCP allocation, and PXE boots into the Ubuntu preseed enviroment. On one or two machines, it gets as far as Ubuntu's DHCP network configuration, and fails. If i pull up a busybox shell (on tty2 on the installing machine), and run ip link, I can see that the UP flag is set on the other NIC. Here's some stuff. host xeon16-ghz240-gb48-node1 { hardware ethernet BC:AE:C5:07:1F:18; filename "pxelinux.0"; next-server 192.168.123.80; } That's what's in dhcpd.conf This is what ip link on the evil machine looks like. Only one NIC is actually connected (deliberately). As you can see, the NIC that's in the dhcpd config, is not marked as UP, and the link that is UP, isn't the one in DHCP. So far I've seen this on two brands of dual-NIC configuration. Does anyone know 1) what's causing it, and b) What we can do about it?

    Read the article

  • NLB NIC w/ Static IP permanently "Acquiring Network Address" after adding more IP's to the cluster

    - by I.T. Support
    We have a 2 node NLB cluster. I recently added more IP's to the cluster range, after which point, the NLB NIC's on both of my nodes ended up in a permanent "acquiring network address" state. The cluster appears to be functioning despite this hang in acquiring an address. We've also rebooted the machines, and these NIC's remain in this state "acquiring network address" even after reboot, which I find troubling. Questions: Does anyone know where I can find documentation on how NLB binds to a NIC? (are there dll's involved, drivers, etc.) Does anyone know of any programs that have known incompatability issues with NLB? We have an application server installed on these NLB nodes (AOL Server) that interacts with the NIC's as well, and I suspect that it might be causing this issue. Before I go directly to Microsoft, I want to gather as much information as possible about the issue. Any help / guidance would be much appreciated...

    Read the article

  • Dual Nic, one keeps dropping

    - by user1215018
    I'm running windows server 2008 r2 on a dell poweredge 2850. I have 2 NICs, one is configured behind a firewall with a dhcp server on the main local LAN and another one has it's own dedicated connection to one of our 13 static IPs. So in a nutshell we have 2 of our static IPs going to this server, one indirectly through a firewall/dhcp server, and the other directly. I am trying to reach IIS on port 80 and port 443. The problem is that the NIC with the direct connection (NIC2) keeps dropping and says either "No internet connection" or "Unauthenticated". However, the NIC behind the firewall (NIC1) has no problems at all. Update: This is the second time this has happened in 3 days and each time the fix has been enabling the dhcp client on the NIC, allowing it to error out to a 169.x.x.x address, then re-enabling the nic with it's static IP assignment.

    Read the article

  • Distribute IP packets accross different NIC queues with MSI (Message Signalled Interrupts)

    - by Ansis Atteka
    NetXtreme II BCM5709 Gigabit Ethernet NIC supports MSI feature (Message Signaled Interrupts) and it has 8 queues. Each queue has its own Interrupt handler in /proc/interrupts. What I am trying to accomplish is to tell NIC which packets should go to which queue. Questions: Is it possible to manually specify which IP packets should go to which queue by encapsulated protocol type (e.g. IPsec packets go in one queue, while TCP packets go in another queue)? If it is possible - how can I do it under Linux? If it is not possible - should I look at MSI-X capable NIC cards to solve this problem? More details: We have one Interface that is terminating IPSec and forwarding/terminating TCP connections. The IPSec packet decryption is inlined (this means that decryption is done under the same ksoftirqd/X context). We are trying to find out if we will be able to improve total performance if IPSec packets will be scheduled on another CPU than TCP packets. One more limitation is that IPSec code is not MP-safe, hence I can not run it under more than one ksoftirqd/X. By default it seems that packets are distributed/hashed by source IP over the 8 NIC queues. The bottleneck is IPSec that chokes out TCP traffic while it is decrypting/encrypting IPSec packets at ~100% CPU. OS is Ubuntu 10.10 (2.6.32-27-server) and NIC is Broadcom BCM5709.

    Read the article

  • Two NIC's 2 Internet Connections, 1 Windows Server 2008 RC2, Routing help required

    - by PJZ
    Hello, I have a Windows 2008 server and 4 other client machines on my home network. I have two internet connections. The main connection is setup with a home router and DHCP on that for all the clients on the network. The secondary connection is just a cable modem which is plugged directly into the server. Local Area Connection: This NIC has an external IP and is connected to the Cable Modem. Local Area Connection 2: This NIC has an internal IP (192.168.0.102) and allows access to all the internal computers. It also has internet access via the local router. So here lies the problem, I want to use the Cable connection on the server for the internet traffic (so that the traffic for server/clients are seperated) but I also need to maintain local access. I am wondering how to make it so that all the internet traffic goes via that NIC because at the moment it goes through the local NIC. As a secondary problem I would also like to forward the connection of one application used by the clients via the server and the cable/server internet because of poor routing for it on the main connection. This perhaps is something for another question though. Thanks for any help you can offer me. Regards PJ

    Read the article

  • Multiple IP addresses on one NIC register twice in DNS server

    - by Brad B.
    Hi, We've got a build server (Windows Server 2008 SP2, 64-bit) which has one NIC and two IP addresses registered to that NIC (192.168.1.30 and 192.168.1.31). The build server is registering two identical Host (A) records for itself in our DNS server: buildserver.example.com = 192.168.1.30 buildserver.example.com = 192.168.1.31 I know in the "Advanced TCP/IP Settings" window for the build server's NIC, under the "DNS" tab, there is a check box labeled "Register this connection's addresses in DNS". I only want ONE of the IP addresses (ending in .30) to be registered in DNS not both of them. Can that be done? My best guess is to disable the "Register this connection's addresses in DNS" and manually add the Host (A) record to our DNS server. Thanks for any help!

    Read the article

  • NIC firmware version on my DL380 G5

    - by ToastMan
    Hi all, I am trying to figure out what is my current NIC firmware version. If I run the latest firmware upgrade from HP, I get the following: It doesn't tell me the current version. If I try to check it from Device Manager, I get this: That's the driver version, not the hardware firmware version. If I reboot the computer, I don't see the NIC firmware during the POST.. How would I go about finding the current firmware version... Thanks a lot! Toast

    Read the article

  • NIC Teaming HP Server running Win2003

    - by Colm
    Hello everyone. I'm new to server NIC TEaming. I have a HP ProLiant DL360 G4p running Win2003 with 2 NICs , only one is currently active. I'd like to activate the 2nd NIC connected (in a active/passive state) to a 2nd switch with only one IP address and ideally only one mac layer address. The 1st switch is a Cisco 2960G and the 2nd is a Cisco C3560G. There are VLANS, RSTP and PAGP in use already. Can someone give me an idea, in broad terms , of what technology/protocols I should be investigating (HSRP, SLB/TLB Teaming etc.) ? I can provide more info if needed. Thanks, Colm.

    Read the article

  • Dedicate a NIC to a Virtualbox VM

    - by John Gardeniers
    On a machine with multiple NICs, running either Windows or Linux, is it possible to dedicate a NIC to a VM such that the host won't even try to use it for itself? I suspect it isn't even possible but if it is, which OS and version and just how would I set it up? The reason for this, apart from academic curiosity, is that I'm trying to set up a network lab for testing purposes. I currently have only a single spare machine, otherwise this wouldn't be an issue. One of the VMs will be the firewall for this lab network, so will need a dedicated NIC for the WAN interface. Neither ESXi nor Xen server will run on the machine, so I have to use a host OS.

    Read the article

  • Kickstarting VMWare ESX 4.1 (Error: No NIC with name bootif)

    - by William
    I'm having an issue kickstarting an installation of VMWaare ESX Classic 4.1. I've stripped down my kickstart a bit to just: accepteula keyboard us auth clearpart --firstdisk --overwritevmfs url --url=10.16.0.1/cblr/ks_mirror/esx-classic-4.1.0-260247 rootpw --iscrypted $1$zZJa3g7g$mD8d.6QgbPku1QovQTAps/ timezone 'US/Pacific' network --addvmportgroup=true --device=vmnic0 --bootproto=dhcp part '/boot' --fstype=ext3 --size=1100 --onfirstdisk part 'none' --fstype=vmkcore --size=110 --onfirstdisk part 'datastore1' --fstype=vmfs3 --size=8920 --grow --onfirstdisk virtualdisk 'esxconsole' --size=7920 --onvmfs='datastore1' part 'swap' --fstype=swap --size=916 --onvirtualdisk='esxconsole' part '/var/log' --fstype=ext3 --size=2000 --onvirtualdisk='esxconsole' part '/' --fstype=ext3 --size=5000 --grow --onvirtualdisk='esxconsole' %post --interpreter=bash However, when I attempt to use this kickstart during a PXE install with no additional kernel options, I get the following error: There was a problem with the Network Device specified on the command line. Error: No NIC found with name bootif If I comment out the network line in the kickstart, the error changes to: There was a problem with the Network Device specified on the command line. Error: No NIC found with name eth0 How can I fix this? Thanks.

    Read the article

  • Two NIC cards with the same metric - Internet traffic going out the wrong one

    - by bvanderw
    I have two NIC cards in my computer - one is connected to our corporate network and the Internet, the other is connected to a private LAN through a Linksys WRT54G. Both cards use DHCP. This was never an issue with Windows XP, but with Windows Vista (and Windows 7) the metric for the 0.0.0.0 route is the same (20), and it appears that some network traffic that should go out my main network card are going out my secondary card instead. The solution to date is to delete the 0.0.0.0 route associated with the second NIC card, but I have to do this several times a day. Is there a better solution? --Bruce

    Read the article

  • Windows Server: specifying the default IP address when NIC has multiple addresses

    - by Cédric Boivin
    I have a Windows Server which has ~10 IP addresses statically bound. The problem is I don't know how to specify the default IP address. Sometimes when I assign a new address to the NIC, the default IP address changes with the last IP entered in the advanced IP configuration on the NIC. This has the effect (since I use NAT) that the outgoing public IP changes too. Even though this problem is currently on Windows Server 2008, I've had the same problem with a Windows Server 2003. How can you set the default IP address on a NIC when it has multiple IP addresses bound? I remark something. When i check route print i see is it there the problem ? 0.0.0.0 0.0.0.0 192.168.x.x 192.168.99.49 261 if i want the default ip be example : 192.168.99.100 There is my route. Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.99.1 192.168.99.49 261 10.10.10.0 255.255.255.0 On-link 10.10.10.10 261 10.10.10.10 255.255.255.255 On-link 10.10.10.10 261 10.10.10.255 255.255.255.255 On-link 10.10.10.10 261 192.168.99.0 255.255.255.0 On-link 192.168.99.49 261 192.168.99.49 255.255.255.255 On-link 192.168.99.49 261 192.168.99.51 255.255.255.255 On-link 192.168.99.49 261 192.168.99.52 255.255.255.255 On-link 192.168.99.49 261 192.168.99.53 255.255.255.255 On-link 192.168.99.49 261 192.168.99.54 255.255.255.255 On-link 192.168.99.49 261 192.168.99.55 255.255.255.255 On-link 192.168.99.49 261 192.168.99.56 255.255.255.255 On-link 192.168.99.49 261 192.168.99.57 255.255.255.255 On-link 192.168.99.49 261 192.168.99.58 255.255.255.255 On-link 192.168.99.49 261 192.168.99.59 255.255.255.255 On-link 192.168.99.49 261 192.168.99.60 255.255.255.255 On-link 192.168.99.49 261 192.168.99.61 255.255.255.255 On-link 192.168.99.49 261 192.168.99.62 255.255.255.255 On-link 192.168.99.49 261 192.168.99.64 255.255.255.255 On-link 192.168.99.49 261 192.168.99.65 255.255.255.255 On-link 192.168.99.49 261 192.168.99.66 255.255.255.255 On-link 192.168.99.49 261 192.168.99.67 255.255.255.255 On-link 192.168.99.49 261 192.168.99.68 255.255.255.255 On-link 192.168.99.49 261 192.168.99.70 255.255.255.255 On-link 192.168.99.49 261 192.168.99.71 255.255.255.255 On-link 192.168.99.49 261 192.168.99.100 255.255.255.255 On-link 192.168.99.49 261 192.168.99.108 255.255.255.255 On-link 192.168.99.49 261 192.168.99.109 255.255.255.255 On-link 192.168.99.49 261 192.168.99.112 255.255.255.255 On-link 192.168.99.49 261 192.168.99.255 255.255.255.255 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 10.10.10.10 261 255.255.255.255 255.255.255.255 On-link 192.168.99.49 261 255.255.255.255 255.255.255.255 On-link 10.10.10.10 261 I need to be certain, when i go on internet i go with the 192.168.99.100 how i do that ?

    Read the article

  • Windows Server: specifying the default IP address when NIC has multiple addresses

    - by Cédric Boivin
    I have a Windows Server which has ~10 IP addresses statically bound. The problem is I don't know how to specify the default IP address. Sometimes when I assign a new address to the NIC, the default IP address changes with the last IP entered in the advanced IP configuration on the NIC. This has the effect (since I use NAT) that the outgoing public IP changes too. Even though this problem is currently on Windows Server 2008, I've had the same problem with a Windows Server 2003. How can you set the default IP address on a NIC when it has multiple IP addresses bound? I remark something. When i check route print i see is it there the problem ? 0.0.0.0 0.0.0.0 192.168.x.x 192.168.99.49 261 if i want the default ip be example : 192.168.99.100 There is my route. Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.99.1 192.168.99.49 261 10.10.10.0 255.255.255.0 On-link 10.10.10.10 261 10.10.10.10 255.255.255.255 On-link 10.10.10.10 261 10.10.10.255 255.255.255.255 On-link 10.10.10.10 261 192.168.99.0 255.255.255.0 On-link 192.168.99.49 261 192.168.99.49 255.255.255.255 On-link 192.168.99.49 261 192.168.99.51 255.255.255.255 On-link 192.168.99.49 261 192.168.99.52 255.255.255.255 On-link 192.168.99.49 261 192.168.99.53 255.255.255.255 On-link 192.168.99.49 261 192.168.99.54 255.255.255.255 On-link 192.168.99.49 261 192.168.99.55 255.255.255.255 On-link 192.168.99.49 261 192.168.99.56 255.255.255.255 On-link 192.168.99.49 261 192.168.99.57 255.255.255.255 On-link 192.168.99.49 261 192.168.99.58 255.255.255.255 On-link 192.168.99.49 261 192.168.99.59 255.255.255.255 On-link 192.168.99.49 261 192.168.99.60 255.255.255.255 On-link 192.168.99.49 261 192.168.99.61 255.255.255.255 On-link 192.168.99.49 261 192.168.99.62 255.255.255.255 On-link 192.168.99.49 261 192.168.99.64 255.255.255.255 On-link 192.168.99.49 261 192.168.99.65 255.255.255.255 On-link 192.168.99.49 261 192.168.99.66 255.255.255.255 On-link 192.168.99.49 261 192.168.99.67 255.255.255.255 On-link 192.168.99.49 261 192.168.99.68 255.255.255.255 On-link 192.168.99.49 261 192.168.99.70 255.255.255.255 On-link 192.168.99.49 261 192.168.99.71 255.255.255.255 On-link 192.168.99.49 261 192.168.99.100 255.255.255.255 On-link 192.168.99.49 261 192.168.99.108 255.255.255.255 On-link 192.168.99.49 261 192.168.99.109 255.255.255.255 On-link 192.168.99.49 261 192.168.99.112 255.255.255.255 On-link 192.168.99.49 261 192.168.99.255 255.255.255.255 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 10.10.10.10 261 255.255.255.255 255.255.255.255 On-link 192.168.99.49 261 255.255.255.255 255.255.255.255 On-link 10.10.10.10 261 I need to be certain, when i go on internet i go with the 192.168.99.100 how i do that ?

    Read the article

  • Adding Static IP's to the NIC

    - by Brett Powell
    We are currently working on migrating a lot of new machines to our network, and my job this morning was to setup all of the IP Addresses. I worked on this all morning, and when I got back tonight I was informed that they had all been setup incorrectly, and had to be removed and re-added. I am quite confused as I have been setting up IP's on machines for a long time and I am curious as to what the issue is. Just taking into account this example... 72.26.196.160/29 255.255.255.248 A /29 block is 5 usable IP's. With the script I wrote and used, the IP Addresses .162 - .166 were added to the NIC. I can't remember now what the name for .161 was, but isn't it the broadcast address or something which isn't assigned to the NIC when adding additional IP Blocks? I am curious as to where my logic is failing me. Not to mention even if .161 was to be added, there is no reason why all of the IPs would have to be removed, as .161 could just be added in addition to these.

    Read the article

  • connect server to server on secondary NIC

    - by microchasm
    Hi, I have a CentOS box with multiple NIC's running Apache. I also have another box running RHEL that will be the MySQL server. I'm trying to use the secondary NIC on the Apache box to connect directly to the MySQL server, but so far no luck. I want to isolate the MySQL box as much as possible which is why I'm going for a direct connection as opposed to running through a switch. I have a crossover cable running between them. IP configs: Apache box eth0 [to lan] ip addr: 192.168.200.100 netmask: 255.255.0.0 gateway: 192.168.111.1 eth1 [to mysql] ip addr: 192.168.200.101 netmask: 255.255.0.0 gateway: [blank] MySQL box eth0 [to apache] ip addr: 192.168.200.203 netmask: 255.255.0.0 gateway: 192.168.200.201 The rest of our network is on 192.168.111.0/24 subnet. Ping only returns Destination Host Unreachable. I've tried various variations of this setup (including straight through cable), and I can't seem to get them to talk to each other. Any help appreciated.

    Read the article

  • Dual NIC internet access

    - by JavaRocky
    Q1. If a computer had two NICs, lets say windows, on which interface would HTTP traffic (or any for that matter) go out on. Not sure how the routes table would look like. Q2. If one of the NICs link becomes unresponsive, would traffic be automatically routed to the other NIC? Thanks.

    Read the article

  • What are the steps to set up a Hyper-V solution with one NIC

    - by Cameron Aziz
    I have successfully installed centos on a virtual machine via Hyper-V on Windows Server 2008 R2. This server has one NIC. I have created a virtual NIC, and virtual subnet, and within the virtual machine (via console) I can ping the gateway. But not google. Is there certain steps I am missing, I feel like I'm one setting away. Im not sure what other information would be useful. Here is the ipconfig of the host: Ethernet adapter vNIC losangeles1_1: Connection-specific DNS Suffix .. : IPv4 Address. . . . . . . . . . . : 10.10.0.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix .. : IPv4 Address. . . . . . . . . . . : 72.51.43.43 Subnet Mask . . . . . . . . . . . : 255.255.255.192 Default Gateway . . . . . . . . . : 72.51.43.1

    Read the article

  • NIC Bonding/balance-rr with Dell PowerConnect 5324

    - by Branden Martin
    I'm trying to get NIC bonding to work with balance-rr so that three NIC ports are combined, so that instead of getting 1 Gbps we get 3 Gbps. We are doing this on two servers connected to the same switch. However, we're only getting the speed of one physical link. We are using 1 Dell PowerConnect 5324, SW version 2.0.1.3, Boot version 1.0.2.02, HW version 00.00.02. Both servers are CentOS 5.9 (Final) running OnApp Hypervisor (CloudBoot) Server 1 is using ports g5-g7 in port-channel 1. Server 2 is using ports g9-g11 in port-channel 2. Switch show interface status Port Type Duplex Speed Neg ctrl State Pressure Mode -------- ------------ ------ ----- -------- ---- ----------- -------- ------- g1 1G-Copper -- -- -- -- Down -- -- g2 1G-Copper Full 1000 Enabled Off Up Disabled Off g3 1G-Copper -- -- -- -- Down -- -- g4 1G-Copper -- -- -- -- Down -- -- g5 1G-Copper Full 1000 Enabled Off Up Disabled Off g6 1G-Copper Full 1000 Enabled Off Up Disabled Off g7 1G-Copper Full 1000 Enabled Off Up Disabled On g8 1G-Copper Full 1000 Enabled Off Up Disabled Off g9 1G-Copper Full 1000 Enabled Off Up Disabled On g10 1G-Copper Full 1000 Enabled Off Up Disabled On g11 1G-Copper Full 1000 Enabled Off Up Disabled Off g12 1G-Copper Full 1000 Enabled Off Up Disabled On g13 1G-Copper -- -- -- -- Down -- -- g14 1G-Copper -- -- -- -- Down -- -- g15 1G-Copper -- -- -- -- Down -- -- g16 1G-Copper -- -- -- -- Down -- -- g17 1G-Copper -- -- -- -- Down -- -- g18 1G-Copper -- -- -- -- Down -- -- g19 1G-Copper -- -- -- -- Down -- -- g20 1G-Copper -- -- -- -- Down -- -- g21 1G-Combo-C -- -- -- -- Down -- -- g22 1G-Combo-C -- -- -- -- Down -- -- g23 1G-Combo-C -- -- -- -- Down -- -- g24 1G-Combo-C Full 100 Enabled Off Up Disabled On Flow Link Ch Type Duplex Speed Neg control State -------- ------- ------ ----- -------- ------- ----------- ch1 1G Full 1000 Enabled Off Up ch2 1G Full 1000 Enabled Off Up ch3 -- -- -- -- -- Not Present ch4 -- -- -- -- -- Not Present ch5 -- -- -- -- -- Not Present ch6 -- -- -- -- -- Not Present ch7 -- -- -- -- -- Not Present ch8 -- -- -- -- -- Not Present Server 1: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:55 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:28:ae USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:28:af USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.52.1 NETMASK=255.255.0.0 GATEWAY=10.200.2.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:55 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:ae Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:af Server 2: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:a7 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:30:30 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:30:31 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.53.1 NETMASK=255.255.0.0 GATEWAY=10.200.3.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:a7 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:30 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:31 Here are the results of iperf. ------------------------------------------------------------ Client connecting to 10.200.52.1, TCP port 5001 TCP window size: 27.7 KByte (default) ------------------------------------------------------------ [ 3] local 10.200.3.254 port 53766 connected with 10.200.52.1 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 950 MBytes 794 Mbits/sec

    Read the article

  • Windows Server 2008: specifying the default IP address when NIC has multiple addresses

    - by Cédric Boivin
    I have a Windows Server which has ~10 IP addresses statically bound. The problem is I don't know how to specify the default IP address. Sometimes when I assign a new address to the NIC, the default IP address changes with the last IP entered in the advanced IP configuration on the NIC. This has the effect (since I use NAT) that the outgoing public IP changes too. Even though this problem is currently on Windows Server 2008 How can you set the default IP address on a NIC when it has multiple IP addresses bound? There is more explication on my probleme. Here is the ipconfig DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.99.49(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.51(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.52(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.53(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.54(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.55(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.56(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.57(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.58(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.59(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.60(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.61(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.62(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.64(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.65(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.66(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.67(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.68(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.70(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.71(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.100(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.108(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.109(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.112(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.63(Duplicate) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.99.1 If i do a pathping there is the answer, the first up is the 99.49, also if my default ip is 99.100 Tracing route to www.l.google.com [72.14.204.99] over a maximum of 30 hops: 0 Machine [192.168.99.49] There is the routing table on the machine Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.99.1 192.168.99.49 261 10.10.10.0 255.255.255.0 On-link 10.10.10.10 261 10.10.10.10 255.255.255.255 On-link 10.10.10.10 261 10.10.10.255 255.255.255.255 On-link 10.10.10.10 261 192.168.99.0 255.255.255.0 On-link 192.168.99.49 261 192.168.99.49 255.255.255.255 On-link 192.168.99.49 261 192.168.99.51 255.255.255.255 On-link 192.168.99.49 261 192.168.99.52 255.255.255.255 On-link 192.168.99.49 261 192.168.99.53 255.255.255.255 On-link 192.168.99.49 261 192.168.99.54 255.255.255.255 On-link 192.168.99.49 261 192.168.99.55 255.255.255.255 On-link 192.168.99.49 261 192.168.99.56 255.255.255.255 On-link 192.168.99.49 261 192.168.99.57 255.255.255.255 On-link 192.168.99.49 261 192.168.99.58 255.255.255.255 On-link 192.168.99.49 261 192.168.99.59 255.255.255.255 On-link 192.168.99.49 261 192.168.99.60 255.255.255.255 On-link 192.168.99.49 261 192.168.99.61 255.255.255.255 On-link 192.168.99.49 261 192.168.99.62 255.255.255.255 On-link 192.168.99.49 261 192.168.99.64 255.255.255.255 On-link 192.168.99.49 261 192.168.99.65 255.255.255.255 On-link 192.168.99.49 261 192.168.99.66 255.255.255.255 On-link 192.168.99.49 261 192.168.99.67 255.255.255.255 On-link 192.168.99.49 261 192.168.99.68 255.255.255.255 On-link 192.168.99.49 261 192.168.99.70 255.255.255.255 On-link 192.168.99.49 261 192.168.99.71 255.255.255.255 On-link 192.168.99.49 261 192.168.99.100 255.255.255.255 On-link 192.168.99.49 261 192.168.99.108 255.255.255.255 On-link 192.168.99.49 261 192.168.99.109 255.255.255.255 On-link 192.168.99.49 261 192.168.99.112 255.255.255.255 On-link 192.168.99.49 261 192.168.99.255 255.255.255.255 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 10.10.10.10 261 255.255.255.255 255.255.255.255 On-link 192.168.99.49 261 255.255.255.255 255.255.255.255 On-link 10.10.10.10 261 How i can be sure the ip use in the image ( suppose to be the default ip address ) will be use by my server as the default address ?

    Read the article

  • Missing NIC and USB devices

    - by MJ
    Coming into work today, I've found we have a fwe different computers (different companies/networks/OS versions - all windows based) that are all having the same issue. 1) Network NIC is not able to be viewed from network connections. If you refresh, its saying the service is not started. Services state the service is started and running. 2) USB devices are not recognized when plugged in, scan for hardware changes, etc. We have managed AV, that is kept up to date, and a managed patch policy that has all these machines at the most recent patch. I'm just wondering if anyone else has experienced these same symptoms, and what they have done to resolve them.

    Read the article

  • Site stopped working after adding NIC card

    - by Sachin Kainth
    My boss made a bit of blunder yesterday, he added a secondary NIC card to the a machine hosting a website so that it could be part of the local network. He also added it to the <blah>.local domain (which all our servers are being added too). The website failed following this. He thought this was because the machine was now called <blahblah>.<blah>.local, so he removed it from the domain and restarted. Same problem a asp.net error, something to do with a binding error. Sorry he didn’t make a note of it. He traced it back to the WCF services that are running on the site. Anyway, it looks like ASP.NET gets confused connecting to the database when there’s multiple network cards. The 173.x.x.x IP address (which is internal), doesn’t route to the internet.. Therefore it’s trying to connect via the wrong network. Any ideas about how to resolve it?

    Read the article

  • Enabling 8021q on a nic

    - by Chris Phillips
    Hi, I'm trying to get a vlan interface on a bonded nic (Centos 5.5) and whilst the interface has been very happily created with vconfig I'm seeing no traffic on it at all. Running tcpdump and tshark on the underlying eth0 I see no sign at all of vlan tags in the traffic, and I'm wondering if there's somethign I'm missing on the server side as the network dept say they are sending me the tagged data. I've got the 8021q module loaded, however under lsmod it shows it's only being used by the cxgb3 module, for an unused onboard iSCSI card, whereas my nics (on an HP DL380 G7) are driven by bnx2 and e1000e modules. Should these modules be listing 8021q as used module? should I have something conrete in /etc/modprobe.conf? Thanks Chris

    Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >