Search Results

Search found 7875 results on 315 pages for 'wired networking'.

Page 103/315 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >

  • Problem with Lenovo x200s Wifi under Ubutu Karmic

    - by oneself
    Hi, I have just gotten my Lenovo X200s laptop, and I am install Ubuntu 9.10 Karmic on it. The installation went through without a hitch, but I can't get my wifi to work. lspci | grep Network Produces the following results: 00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03) 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10) The weird part is that when I turn the wifi hardware stitch on and off on the side of the laptop, I get the following printed in /var/log messages: Dec 30 23:24:48 temp-laptop kernel: [ 213.432302] usb 4-2: USB disconnect, address 2 Dec 30 23:24:52 temp-laptop kernel: [ 217.276310] usb 4-2: new full speed USB device using uhci_hcd and address 3 Dec 30 23:24:52 temp-laptop kernel: [ 217.441759] usb 4-2: configuration #1 chosen from 1 choice Does Ubuntu think my wifi card is a USB device? Am I missing some driver? What can I do to fix this? Please, help!

    Read the article

  • Sharing Windows 7 Hard drive with Windows XP Hard drive

    - by Ginzo Milani
    I wish to share my hard drives between my two computers but I seem to be running along some sort of error... my windows XP Computer is picking up my "XGaming" hard drive but when clicked it says access is denied, despite there is no password set up(I followed this: http://www.howtogeek.com/howto/windows-7/share-files-and-printers-between-windows-7-and-xp/) I also tried to share my C and J drives on my windows XP computer but my windows 7 computer doesn't seem to even detect them!

    Read the article

  • Can I set up multiple accounts on DD-WRT? [closed]

    - by Greg Ros
    Possible Duplicate: Can I set up multiple accounts on DD-WRT? I want to set up multiple accounts on DD-WRT (accounts meaning, username-password pairs). Specifically, I want one to be used primarily for remote web management (though there is no reason to restrict the account to such). Is this possible? If so, how do I go about it? I'm running: Router Model TP-Link TL-WR1043ND Firmware Version DD-WRT v24-sp2 (08/07/10) std - build 14896

    Read the article

  • Troubleshooting an unstable internet connection

    - by Konrad Rudolph
    My MacBook Pro running OS X (10.9, but I had the same problem before) is connected to a Belkin router via WiFi and, using Virgin Media as the ISP, to the internet. The connection is extremely unstable – on some days, I get a ping timeout every few seconds. In addition, some domains seem to suffer general connectivity issues. For instance, I often find that while the youtube.com website loads, none of the videos (which are hosted on a separate domain) do. At other times, videos load but always fail to buffer, even though the actual connection speed is ok, even though I’ve disabled dash playback. Since I’m living in a rented room and the ISP contract isn’t actually mine I’ve got only limited possibilities of addressing the problem. In particular, I have no access to the router configuration and my non tech savvy landlady, while sympathetic, is not in a great hurry to hand the problem over to the ISP’s customer support. What’s more, I seem to be the only person in the house experiencing these problems – but I can imagine that this is simply because I’m the only one who’s using the internet continuously. I’m searching for specific tests that might be able to pinpoint – and ideally solve – the problem. So far all I’ve managed to do is establish that Virgin is routing my traffic in mysterious ways. Here’s an excerpt from traceroute google.co.uk. It’s worth mentioning that the host name doesn’t seem to matter a lot, the trace route is always the same. traceroute: Warning: google.co.uk has multiple addresses; using 62.254.36.148 traceroute to google.co.uk (62.254.36.148), 64 hops max, 52 byte packets 1 (192.168.2.1) 1.112 ms 1.300 ms 2.359 ms 2 10.100.32.1 (10.100.32.1) 11.926 ms 10.217 ms 24.987 ms 3 cmbg-core-1a-ae3-610.network.virginmedia.net (80.1.202.93) 28.809 ms * 66.653 ms 4 popl-bb-1b-ae16-0.network.virginmedia.net (212.43.163.141) 13.759 ms 126.504 ms 20.472 ms 5 nrth-bb-1b-et-010-0.network.virginmedia.net (62.253.175.57) 28.357 ms 16.398 ms 42.387 ms 6 nrth-bb-1c-ae1-0.network.virginmedia.net (62.253.174.110) 27.441 ms 15.622 ms 12.044 ms 7 lutn-icdn-1-ae0-0.network.virginmedia.net (62.253.175.82) 16.678 ms 28.463 ms 28.253 ms 8 * * * 9 * * * 10 * * * ^C If I let it, this goes on until the end of time. It never seems to reach a destination. Is this normal? A friend living in the same town who is also with Virgin Media has a more conventional traceroute output: 7 hops to google.co.uk, all of which send the ICMP TIME_EXCEEDED response. The obvious fix – rebooting the router – doesn’t seem to help. As far as I can tell, the WiFi connection is stable (I can always ping the router) so the problem is further downstream. I’ve tried using an alternative DNS before (OpenDNS) but if anything, this made things worse. In fact, it made all Google services nigh unreachable.

    Read the article

  • How to configure a wireless router to point to a remote www proxy

    - by Mark
    I have a LG smart Tv with browser. I need the tv browser to connect to a uk based proxy server on port 808. Unfortunately there is no option within tv to setup proxy for its browser. Now the Tv connects via a wireless connection to the internet. IE: TV <- D-Link DIR-605L <- ADSL <- WWW. Is it possible to setup this wireless router to connect the TV to the Proxy ?? If so ? where ? and what setings do i need to change in the wireless router ?? In short my question is ? How do i get the wireless router to make up for the lack of proxy connectivity within my Tv browser ?? Thanks in advance NB: I have configured my Pc's browser's proxy settings, and streaming via the proxy works 100%

    Read the article

  • Top ten security tips for non-technical users

    - by Justin
    I'm giving a presentation later this week to the staff at the company where I work. The goal of the presentation is to serve as a refresher/remidner of good practices that can help keep our network secure. The audience is made up of both programmers and non-technical staff, so the presentation is geared for non-technical users. I want part of this presentation to be a top list of "tips". The list needs to be short (to encourage memory) and be specific and relevant to the user. I have the following five items so far: Never open an attachment you didn't expect Only download software from a trusted source, like download.com Do not distribute passwords when requested via phone or email Be wary of social engineering Do not store sensitive data on an FTP server Some clarifications: This is for our work network These need to be "best practices" tips for the end-user, not IT policy We have backups, OS patches, firewall, AV, etc, all centrally managed This is for a small business (less than 25 people) I have two questions: Do you suggest any additional items? Do you suggest any changes to existing items?

    Read the article

  • Does HP 8530w support Wifi 802.11n?

    - by FoxyBOA
    According to vendor site HP 8530w supports 802.11n draft mode. My Windows 7 tell me that network card is 5100 ABG and know nothing about N mode (guys from Intel forum mentioned, that 802.11N versions must ended with N letter, e.g. 5100 ABN). Not sure if it matter, but my laptop model id is #FU462EA. How could I check that my Wifi card compliant with 802.11n (I suspect that "draft N" could have two "special" meaning: doesn't work with 802.11n at all or requires special activation of the mode). Any hints are welcome.

    Read the article

  • What keeps you from changing your public IP address and wreak havok?

    - by Whitemage
    An interesting question was asked to me and I did not know what to answer.. So I'll ask here. Let's say I subscribed to an ISP and I'm using cable internet access. ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let's say, 60.61.62.75 and mess with another consumer's internet access? For the sake of this argument, let's say that this other IP address is also owned by the same ISP. Also, let's assume that it's possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gaetway, a network address and a broadcast address. So that's 3 addresses the ISP "loses" to you. That seems very wastefull for dynamically assigned IP addresses where the majority of customers are.. Could they simply be using static arps? ACLs? Other simple mechanisms? Anyone who worked at an ISP would be willing to explain this a bit?

    Read the article

  • Having trouble setting up my router

    - by indyK1ng
    I just moved into my apartment and the Internet connection is working. It's Comcast in case that matters. Anyway, I'm having trouble setting up my wireless router (Netgear WNR2000) to work with it. Are there any settings that I could be missing? I currently have it set up to use a static IP address and I found the DNS servers I'm supposed to use and the Internet light is green, but I can't get out to the Internet. When I am trying, I'm connecting to an Ethernet port on the back of my router. Is there a setting I'm missing or a setting that I have set wrong? I used the automatic set up wizard to learn that it's a static IP address. Any help would be appreciated. I am currently only able to use my Linux machine, so please make any help in Linux commands. Yes, I can connect to the Internet if I connect to the modem directly and I've been using the web interface when I'm connected to the router, so I suppose I can ping the router. My router detected the connection as using a static IP address, so I connected to the modem directly and figured out what my IP address, gateway, and mask were as well as DNS servers.

    Read the article

  • MikroTik ipv6 Tunnel

    - by MikeSmitty
    I've got a MikroTik router set up with the latest stable OS on it, and I just set up an ipv6 tunnel with Hurricane Electric, but I'm having an odd issue with it. I can't ping anything until I first ping the tunnel endpoint on HE's side. After that I can ping any ipv6 address fine, but give it a little time (say, maybe 30 sec) and I can't ping any ipv6 addresses again. Whenever it stops allowing ping to go through I notice the counter on my firewall rule that drops invalid connections goes up. this is my ipv6 firewall config: add action=accept chain=input comment="" connection-state=established \ disabled=no in-interface=sit1 add action=accept chain=input comment="" connection-state=related disabled=no \ in-interface=sit1 add action=accept chain=input comment="" disabled=no in-interface=bridge \ src-address=ipv6_address_here/64 add action=drop chain=input comment="" connection-state=invalid disabled=no \ in-interface=sit1 add action=drop chain=input comment="" disabled=no in-interface=sit1 Any ideas on what it could be?

    Read the article

  • How to calculate CIDR notation from entries in a routing table

    - by febreezey
    I have some entries in a routing table that were created using longest prefix matching, and I have to use those entries to determine the a.b.c.d/x notation (CIDR). This is an example entry: 11001000 00010111 00010. That was calculated from the range 11001000 00010111 00010000 00000000 through 11001000 00010111 00010111 11111111. I know the range is from IP addresses 200.23.16.0 to 200.23.23.255, but getting the /x for the subnet # doesn't make sense to me. Anyone know how to properly go about calculating it?

    Read the article

  • Finding all domain names that resolve to the same ip?

    - by Janak
    Lately I've been tracking a spammer on craigslist. I recently discovered that he's added a new technique to his arsenal, he registered a whole bunch of domain names but they all resolve to the same ip address. Is there any way to take an ip address and get a list of all the domain names that resolve to that ip?

    Read the article

  • Share the DVB card on windows 7

    - by Bashar Kernel
    I have 2 computers connected to a router and I have a DVB card in one of them. I want to use the one DVB card to feed both of them. I read about it and I know that I want to share the DVB adapter with the Internet Connection Sharing on the LAN network. But when I use the connection sharing, I lose my internet access I tried to use "Bridge Connection", but then I also lost my internet access too. Can any one tell me how to fix this problem? And how to view the channels (for example how to use the VLC)?

    Read the article

  • VPN Network intermittantly fails to provide internet: What could be possible causes

    - by Jake M
    We have a small office with our own VPN setup. We occasionally experience failures in our internet connection where we cannot access the internet. Most of the time the internet connection will resume by itself(without me doing anything) after a period of time(10 mins). Would you be able to suggest possible causes of the connection failure so I can then go and run some tests? Our network architecture is like so: A 'Billion' brand router that is connected to the internet via phone cable and then connected to our Cisco Switch A Cisco Switch/Bus which is connected to all our office nodes, our external harddrive and also to our router as stated above. All connections are via ethernet cable A series of work computers(nodes) connected via ethernet cable to the Cisco switch. Our ISP is TPG Australia We have a Virtual Private Network All the ethernet cables are about 3 years old Do you think that the causes of our intermittant connection problems could be due to the following: Data collisions in the ethernet cables Old/Faulty ethernet cables Our ISP has bad service Can you think of any other causes of the problem?

    Read the article

  • KVM network bridge and public static IP for both host and guests

    - by Javier Martinez
    I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

    Read the article

  • KVM network bridge and public static IP for both host and guests

    - by Javier Martinez
    I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

    Read the article

  • Sonicwall 3500 (Creating VLANS for usage of multiple SSID)

    - by Thomas Chia
    I have an issue here. Here is my setup: X0 - STAFF network | X2 - AGENT network | X4 - Wireless AP (for multiple SSID) Okay, basically I'm going to set up the wireless AP to be broadcasting 2 SSID, STAFF-WIFI and AGENT WIFI. When connected to STAFF-WIFI, the users will be connected to the STAFF network, while connected to the AGENT WIFI, the users will be connected to the AGENT network. Can someone explain in details how to go about setting up this configuration? Thanks!

    Read the article

  • Windows 7 - Local Area Connection Adapter is disabled

    - by teepusink
    I just got Windows 7. However, I'm now unable to connect to the internet. Doing the diagnosis gives me these: There might be a problem with the driver for the Local Area Connection Adapter The Local Area Connection 2 Adapter is disabled How do I resolve those? These are the things I've tried: In cmd do ipconfig /renew In Device Manager, go to Network Adapter. (I don't see any red exclamation marks)

    Read the article

  • Configure an Azure VM for Dynamic DNS for Cloud Services

    - by Adam
    I am trying to setup an azure VM with proper DNS to allow multiple cloud services to communicate across cloud service boundaries. As I understand it, I need to provide my own DNS server. I do not have any on-premise infrastructure, so I am trying to configure an Azure VM to act as my DNS. This SO question (http://stackoverflow.com/questions/21858926/azure-how-to-connect-one-cloud-service-with-other-in-one-virtual-network) is very similar to my setup. This article (http://msdn.microsoft.com/en-us/library/windowsazure/jj156088.aspx) describes my particular case: Name resolution between virtual machines and role instances located in the same virtual network, but different cloud services Here is what I have done: Created Azure Virtual Network and declared subnets for each of my cloud services. Created an Azure VM (Windows 2012 R2) with DNS enabled RDP to the VM and enabled the DNS role and installed features Added the appropriate NetworkConfiguration xml section to each of my cloud services .csfg files Re-deployed my cloud services I have verified that I setup the virtual network and networkconfiguration properly because my cloud service hosts are able to communicate with each other if I use the internal ips. However, name resolution doesn't appear to be working, and it doesn't appear that my cloud service roles can communicate with my DNS server. How do I configure my VM so that my different cloud services roles register themselves with my DNS server? EDIT: I think I am 1 step closer to getting this to work. The cloud services that I was using are in an old affinity group which is not supported by VMs, so I was unable to add my VM into my virtual network. I created a new VNET in a new affinity group with my VM added into it. However, I still don't know how to configure the azure VM's DNS server so that the cloud services register themselves for name resolution. Also, an added bonus guaranteed to get a +1 would be to explain if it is possible to register a DNS entry for the VIP for an internal endpoint of my cloud services so we can get load balancing. Thanks!

    Read the article

  • VMware vSwitches and Dell PowerConnect BPDU guard

    - by dunxd
    I am using two Dell PowerConnect 6248 switches to connect a VMware host vSwitch. A discussion of config of Cisco switches for use with VMware advises to set physical ports connected to vSwitch with bpduguard and portfast. However, Dell switches don't have the bpduguard setting for individual ports. I can switch it off globally for all portfast ports, but I don't think I want to do that. Should I: Disable STP on the vSwitch connected ports? Leave STP on and enable portfast on the ports, and forget about bpduguard? Disable bpduguard on all portfast ports via global config Do something else? See also: VMware vSwitches and spanning tree

    Read the article

  • How to Set Linux Bonding Interface to Gigabit

    - by Kyle Brandt
    I have enabled Linux active backup mode bonding. Each interface is a gigabit interface, but the bond interface seems to end up at 100 Megabit: bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full. ... bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON ... bonding: bond0: backup interface eth1 is now up ethtool apparently can't provide info on bond: sudo ethtool bond0 Settings for bond0: No data available So does this mean I am operating at 100 or 1000 Megabit (My guess is 1000)? If it is only 100, what options in the ifcfg scripts or the modprobe bonding options do I need to sett to make it 1000?

    Read the article

  • Wake On Lan for Fedora 12

    - by Toymakerii
    I have a fedora 12 box that I am using as a sandbox for web development and a few other toys. The box gets really hot so I would like it to sleep/hibernate when no one is using it, however most of the people connecting to the box will not be able to access it physically. Is it possible to set up a Wake On Lan that wakes up the machine when it detects an SSH connection? A google search didn't yield much information. (or atleast I wasn't smart enough to register it as useful!)

    Read the article

  • Anytime I upload something, my internet slows down extremely. What can I do?

    - by Earlz
    Title says it all. For a bit more info though: Basically, I have Time Warner cable internet. My speeds maintain a stable 2Mbit/s upload and 20Mbit/s download with average ping times around 30ms. This crazy thing happens though when I upload anything. I went to upload a 200M file to my server today through sftp and my internet completely choked up. I speed tested it during this upload and my ping time was around 800ms, download speeds of 0.2Mbit/s and Upload speeds of 0.3Mbit/s. Note, I wasn't downloading anything during this time either. It is just straight upload. What is it that causes this phenomenon? My router is OpenBSD. Is there anything I could set up to fix this problem(by queues or some such), or is this a problem with cable internet?

    Read the article

  • Two identical fiber optic broadband lines working as one

    - by Katafalkas
    I have been trying to find an answer to this, but all I can find is hobbyists trying to connect their Linksys devices to get some magic out of them. I am looking for a way I could combine two 100Mbit fiber optic lines into a single connection for our office. I assume it involves some Cisco learning or something similar. Do I need to configure some big router to load-balance the NATing in some way? I assume that many of you have done something similar and hope someone could share their knowledge or at least provide me some tips on how to do this.

    Read the article

  • Bandwidth Control on our Internet Connection

    - by AlamedaDad
    Hi all, I have Covad dual/bonded T1 service in our office coming through a Cisco 1841 and then through a Sonicwall 3060Pro/Enhanced SW firewall. The problem I'm looking for some input on is how to limit the amount of bandwidth any single user/PC can user for downloading a file from the Internet. It's become an issue that when one person happens to download let's say an ~300MB file, normal internet access for the other employees slows to a crawl. I've seen through MRTG that in fact usage of the circuit jumps to the full 3mb for the duration of the download and then drops. Is it possible to control this? I'm not familiar with QOS or the like so I'm not sure. Any help on this would be appreciated. Thanks...Michael

    Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >