Search Results

Search found 1543 results on 62 pages for 'motherboard'.

Page 2/62 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Find the model of my motherboard without opening the computer [closed]

    - by Code
    Possible Duplicate: Find out what the motherboard on my computer is I need to find the model of my motherboard so I can find what soundcard/chip it uses so I can get some drivers for it. Is there anyway to get this from inside XP? I looked through device manager but haven't seen anything that would tell me. I built the system over a year ago and don't have any receipts to check what it was.

    Read the article

  • Monitor attached to motherboard is out of frequency

    - by Neilvert Noval
    I don't know if this is appropriate to ask it here in superuser. Please, just route this to appropriate stackexchange site if found unrelevant. Here's my scenario. I have bought a new motherboard (MSI 785GT-E63). I already have an old CRT monitor connected to it. After I install a linux OS to it, my monitor will display that it is: Out of frequency. Current frequency is 89Hz. The operating output of my monitor is (around) 60-70Hz. I would like to get this thing work. How can I let my CRT display properly? I was thinking of lowering down video frequency output of my motherboard, but I can't find any settings on my BIOS setup. Additional info: My monitor is attached directly to the built-in video adaptor of my motherboard. (No additional video cards) Install of OS is complete without errors. Please help.

    Read the article

  • Installing a new Motherboard in a HP xw6200 case

    - by thing2k
    I have a HP xw6200 Workstation, that is rather long in the tooth, and with 2 physical CPUs, it is quite inefficient. So, the plan was to upgrade the internals. Nothing special: AMD Athlon II X4 640 ASUS M4A78KT-M LE (mATX) 2x 2GB DDR3 1333MHz RAM. 3p under my £150 budget The issues: The pin connector for the front panel isn't a good fit, but I can trim it to size. The PSU has a 8-Pin Power connector, unsurprisingly, the new board has a 4 pin socket. The pins do line up, but I would have to cut it in half to fit. Finally, due to the weight of heat-sinks, they are screwed directly into the case. It turns out that these screws also lock the motherboard in place. As to remove it, you remove the heat-sinks, slide the motherboard across and lift it out. I tested the new board for fit, and while it slots in fine, it's not secure. There is nowhere to screw the board down, it is just held in place with plastic standoffs. The only idea I had, was to wedging something between the side of the motherboard and part of the case. Any suggestions?

    Read the article

  • Is the motherboard the cause of these errors?

    - by ianfuture
    Motherboard is : ASUS A7N8X-E Deluxe, Rev1.01, On start up get: "cmos checksum error - defaults loaded" error BIOS is reset everytime and can't boot to Windows off HDD. POST report is ok once I tell it there is no Floppy drive attached and not to seek it. The boot sequence starts then just as get to load windows safe mode options whole PC shuts down. BIOS is reset to defaults again. I've checked the battery and jumpers. Tried a known working battery. Changed Graphics card, changed memory, changed HD to one without an OS. Disconnected DVD drive. PSU is known to be ok. IN BIOS CPU is recognised correctly and memory is also recognised ok. So is it likely to be a bad motherboard or corrupted BIOS or something else? Thanks :)

    Read the article

  • The computer after motherboard replacement turns on and off continually

    - by Marcin Rybacki
    Hi guys, First of all I would like to stress I'm beginner and probably I'm not doing something right. I replaced my old motherboard (AK35S20C Schuttle) with a new motherboard (Soltek SL-75DRV75). Unfortunately the replacement isn't working as expected. Symptoms are: The computer powers on, works less than a second and powers off. Then it powers on again and so on. It doesn't emit any sound, it looks like it resets very quickly. Do you have any suggestions what might be the problem?

    Read the article

  • Computer not working, motherboard is suspect

    - by Arlen Beiler
    I have a problem with my computer. I have a GeForce 6100 M9 Motherboard, which I suspect is broke. The capacitors beside the CPU are corroded and the computer doesn't do anything except start the fans when I push the power button. The problem is that I can't find another motherboard as they apparently don't sell this model anymore. I have tested the Power Supply and it appears to be working. Any advice would be appreciated. Different forums have mentioned that you can replace the capacitors. Any help on this would be appreciated.

    Read the article

  • Motherboard RAM question.

    - by winterwindz
    Firstly I'm new at this. Not a very computer-ish person. So I very much apologize if this is not the right place, but here it goes.. My Motherboard is an Asus P5LD2-SE. I'm running in Win 7 Ultimate 32-bit(x86) OS, 1GB RAM (2x512 MB). I'm planning to upgrade my OS to 64-bit and because I know my Motherboard is a dual-channel, I bought a dual-channel 2 GB RAM (2 pcs). My question is; am I still able use my old RAM ones, since it is 4 slots..? Which in the end will show 5GB. Is it possible? Thank you for your time. =)

    Read the article

  • How to configure an ASUS motherboard.

    - by Absolute0
    I have an ASUS P7P55-M motherboard running with an Intel Core i5-750 processor and 4 GB RAM with 1600 MT/s speed. For some reason the default settings of the motherboard make all the components run at half their optimums. I have switched to the "D.O.C.P." profile and supposedly everything is as it's supposed to be (verified with CPU-Z). There is also an "X.M.P." profile and a manual one. Are either of the DOCP or XMP safe to go with? I wouldn't use the manual mode as I would likely mess something up real bad. XMP seems to be more memory oriented.

    Read the article

  • Some Memory Slots Not Working on MSI FM2-A85XA-G65 Motherboard

    - by Mike Ciaraldi
    Short version of question: Does anyone have an MSI FM2-A85XA-G65 motherboard, who can confirm that all four memory slots work? Long version: Several months ago I bought an MSI FM2-A85XA-G65 motherboard at Newegg. At that point I installed an AMD A8-5500 processor and two sticks of Corsair Vengeance 8 GB DDR3-1866 memory, and put it into my file server. I installed the RAM in slots 1 and 3, as directed in the manual, to enable dual-channel memory access. It seemed to work fine, so I bought a second identical mobo (which arrived dead, but was quickly replaced by Newegg) and set of RAM, installed an A10-5800K, and put that into my production Linux machine. Again, it seemed to work well. Eventually I happened to notice that on the server only 8 GB of RAM appeared in the BIOS. I tried each of the slots and memory modules individually and in various combinations. I even swapped processors with the production machine. The result was that putting memory in slots 1 and 2 worked (showing a total of 16 GB), but any memory in slots 3 or 4 was not recognized. However, all four memory slots in the production machine worked, and I confirmed this with both processors. I contacted MSI and arranged to ship the defective mobo back to them for replacement under warranty. I did not want my file server to be down in the interim, and I had another machine I wanted to upgrade, so I bought a third identical mobo to use. That one had the same problem -- only memory slots 1 and 2 worked. I tested it thoroughly with multiple processors and memory sticks. I sent the defective mobo back to MSI and they sent me a new one. This has the same memory slot problem. So I sent it back. The replacement arrived the other day and shows the same problem. I contacted MSI yet again and they said that nobody else has reported memory slot problems on this board and it must be my processor. So my score so far is, out of six boards of this model, I have: One where all four slots work. One which was dead on arrival. Four where only memory slots 1 and 2 work. Before I tear my other machines apart and start swapping processors again I thought I would ask if anyone else has this exact model motherboard and could confirm that all four memory slots either do or do not work. According to MSI you should be able to just plug a single memory module into any of the slots and it will work (and it does on the one mobo I have which works correctly). If you have not yet used all four slots, this is a good time to test them so you know if you can expand your memory in the future. Thanks in advance to anyone who can help.

    Read the article

  • Motherboard: Intel S5520HCR s1366 SSI EEB

    - by Crazy_Bash
    I'm building a storage server for online video streaming. I thought about adding two SSD drive for a OS. other 15*(12 SATA & 3 SSD) drives i want to build with aufs XFS and ethernet 4GB/sec network. But I'm confused a little. S5520HCR board supports 6, SATA/300, RAID: 0, 1, 10, Intel ICH10R. Does it mean i can use SATAIII HDD? I'm planing on buying SEAGATE SV35 Series (3.5, 3??, 64??, SATA III-600). also my Chassis supports up-to 16 sata and the motherboard only 6 what kind of sata controller should i use? What's better in terms of performance 1366 or 2011 socket? My server so far: AIC RSC-3EG-80R-SA1S-2 3U Motherboard: Intel S5520HCR s1366 SSI EEB Kingston DDR3 8192Mb PC3-10600 1333MHz (KVR1333D3N9/8G) Seagate 3000GB 64MB 3.5" 7200rpm SATAIII (ST3000DM001) Kingston 480GB SSD 2.5" SATAIII Intel E1G44HTBLK Intel Xeon E5606 2133MHz/L3-8192Kb/QPI s1366 tray SERVER ACC CARD SAS PCIE 16P HBA 9201-16I LSI00244 SGL LSI

    Read the article

  • Add SATA Port to Motherboard?

    - by YAS
    I recently took off the bottom covers to my laptop, an Aspire 6930, and one of the covers was hiding an empty space large enough for a second hard drive. The bit of motherboard that was showing had the solder joints for a SATA port, but no port. What I'm wondering is; If I get a spare SATA port and solder it in would it mess up my motherboard and kill my laptop? I'm not concerned about a clean solder job, I can do that. But if the port is soldered in cleanly if there would be any danger to doing it. It'd be pretty darn awesome to get a second hard drive in my laptop.

    Read the article

  • Motherboard not recognizing memory anymore

    - by root
    I bought some new RAM and installed it on my motherboard. But, the BIOS would not post. There's an LED on my motherboard that shows error codes, and it showed the error: No usable memory detected. So, I removed the new memory and reinstalled the old memory, thus restoring the computer back to its original configuration. But, the BIOS still would not post, still giving the error: No usable memory detected. I've ensured that the memory and power headers are seated properly. I've tried all possible combinations of memory slots, and I've also reset the CMOS, but the error remains the same. The computer was working fine before I tried upgrading the memory, and I originally assembled the computer myself. What are some possible causes of this problem?

    Read the article

  • New SSD freezing on older motherboard (intel G31)

    - by DJM
    I have an ECS G31T-M motherboard running a Core2 Quad processor, 4gb RAM, Windows 7 32bit, Geforce 9600GT. Bought a Sandisk Extreme III 120GB (SDSSDX-120G-G25) and installed today. I'm outputting this from my 9600GT with included TV-out adapter to Component video (to my HDTV). This motherboard is SATA 2 and from what I can tell, SSDs run on the IDE controller and there is nothing fancy to set up advanced features of SSDs. I've noticed on other forums (but not verifying with ECS) this board does not support AHCI. I have two versions of Windows 7 installed on two drives, the SSD and an old 500G disc drive. When booted from my older 500G HDD, video plays fine on the HDTV. When booting the SSD windows 7 install, I am freezing constantly, as in, video plays OK for a minute, then picture freezes for 1-3 minutes (sometimes as audio continues playing) and returns for 20-30 seconds before doing the same thing again. Other tasks such as basic maneuvering through file folders seems to be no problem. Please help!! Do I need a new system for this thing to work, or could there be other fixes? I updated firmware to R201 to no avail. DJM

    Read the article

  • Motherboard running rather hot while gaming

    - by I take Drukqs
    Case: Antec 1200 Mobo: Gigabyte GA-X58A-UD3R CPU: Intel i7 950 (stock cooler) GPU: EVGA GeForce 570 GTX RAM: 2x 2 GB (4 GB total) DDR3 dual-channel Corsair OS: Windows 7 Home Premium 64-bit This is my first build and it's brand new. I had no problems putting it all together in a few hours one evening and I consider myself to be pretty good with computers. Not to brag or anything like that! Just saying I've been fiddling with them since I was in diapers and I have a good amount of experience under my belt, just not with certain things yet. Recently while playing many of the latest games maxed out without a hitch my motherboard has been running hot and like anyone who's ever built a computer it scares the life out of me. I checked HWMonitor and saw that my motherboard sometimes reached temperatures of around 52 - 78c (the number 78 obviously being what's scaring me). I was wondering if such a temperature is normal and if not what the problem could be. Air flow in my case is phenomenal and besides having to ship back a faulty GPU and reseat my CPU my first build has been a very large success which I am enjoying tremendously. There is literally almost no dust in my case due to it being very new as previously mentioned and my RAM sticks are in the correct slots for dual-channel mode. My cable management is pretty great in my opinion with only cables from my PSU lingering in the bottom of the case. At any given opportunity I ran my cables behind my mobo. Air flow should definitely not be a problem because my CPU only goes up to about 60c and my GPU only goes up to about 80c. Thank you very much in advance.

    Read the article

  • Power supply switch like stays off motherboard light turns on

    - by Sion
    I bought a computer at the thrift store yesterday. The computer powered on without any error beeps. Getting it back to the house determined that the CD and hard drive needed to be changed. Put in a populated hard drive to check, the computer turned on and seemed to function. Put in a new CD drive, and just put in a new Hard drive. I plugged it in to check and I noticed that the light for the power supply switch did not come on. But I did notice that the light on the motherboard is lit. and I could not turn the computer on. To help troubleshoot it I unplugged the CD and Hard drive. then re-plugged the power supply and switched it on and off. Nothing changed. Parts: Motherboard: Digital Home PSW DH deluxe Power Supply: FSP-Group FX700-GLN Did I accidentally unplug something while installing the hard drive? Is the Power supply fried somehow?

    Read the article

  • CPU not working on a specific motherboard

    - by Shaman
    I'm making a computer for someone and I met a weird problem. The CPU that I have doesn't work on this motherboard. The CPU is an Intel Pentium D 925 and the motherboard is an ECS G41T-M6, which in theory should work together. The only thing reused is the power source(400W). When I start the computer, the fans start, and that's it. The BIOS doesn't boot. I tried my own power source (600W Corsair) and nothing. Removed the RAM, no warning. In desperation I tried the last thing, swaped my own CPU with this one (Core2Duo E7200). Lo and behold, it worked. Both. The Core2Duo worked on the ECS with the old power source and the RAM that I used in the first place, and the Pentium D worked on my Gigabyte G31M-ES2L. What I discovered was that the Pentium D didn't receive power on the ECS, because I tried running it without the cooler and it remained at room temperature. On a side note, I also removed the HDDs just in case. So, in conclusion, any ideas? I can't return it, and I can still use it to upgrade another PC, but I would really prefer not to buy another CPU if possible.

    Read the article

  • Intel Motherboard Lightning Victim Dies Hard

    - by Stetson RDT
    Today, I have a more hardware-related question. I have an Intel board, and I really do not know which board it is, I built the machine for a relative, but he forgot to keep the documentation. Long story short, the computer was disconnected during a lightning storm, but a lightning strike travelled in via the ethernet cable (It was directly connected to a power brick commonly seen on those long distance ISP Wireless transmitters), and the motherboard was shocked. I am attempting to get this PC going. The problem is as follows: The computer will randomly reboot, just in the middle of anything as it pleases. May load to EFI (or whatever BIOS is nowadays), may load to bootloader, may even get to the OS. But before 5 minutes is up, the system will always die. Out of curiosity, I plugged my voltmeter in to a molex connector. On the 5V side, it gets a good, consistant +5.13V. On the 12V side, it fluctuates, as follows: Upon immediate startup, it soars to 12.11-12.13V. It will now do one of two things: it will immediately jump down to 12.04-12.05V, or hover for about a minute at 12.11-12.13, then jump down. It seems the longer the voltage stays at 12.11-12.13, the shorter the machine will stay running. Also, post codes, whenever the machine locks up, but does not die hard, seem to be between "AA" and "AC". Does this make any sense to anybody? Do you all think this motherboard is salvageable? It was an expensive bugger, and I'd prefer to not replace it.

    Read the article

  • Processor with higher FSB than motherboard can support.

    - by Wesley
    Hi all, Please redirect me if there is a similar question, but I have an ECS P4VXASD2+ (V5.0) motherboard, which supports a 533 MHz FSB. I want to put in a Pentium 4 3.2 GHz processor (Socket 478) with an FSB of 800 MHz. Would this be possible? Would the FSB of the processor just be limited to 533 MHz? Thanks in advance.

    Read the article

  • Processor with higher FSB than motherboard can support.

    - by Wesley
    Hi all, Please redirect me if there is a similar question, but I have an ECS P4VXASD2+ (V5.0) motherboard, which supports a 533 MHz FSB. I want to put in a Pentium 4 3.2 GHz processor (Socket 478) with an FSB of 800 MHz. Would this be possible? Would the FSB of the processor just be limited to 533 MHz? Thanks in advance.

    Read the article

  • Broken Motherboard Trace

    - by CoffeeBean
    When you're fairly certain that a motherboard trace is broken near the CPU (i.e.: you suspect heatsink / fan was improperly inserted) is it advisable to attempt a repair? I've heard that it can be done using a substance for repairing embedded windshield defoggers. Has anyone had any experience with this?

    Read the article

  • USB Ports not working on new ASUS Z87 PRO motherboard

    - by Peter Coulton
    3 of the six USB ports on the back on my new ASUS Z87 PRO motherboard are not functioning properly. They do seem to deliver power, just don't seem to function for data (devices attached in these ports are detected by windows, or usable in UEFI) I think I'm right in saying that the top 4 ports (3 of which aren't working) run off an additional USB controller (not from the Z87 chipset) if that makes any difference. I'm pretty sure that I'll just have to return it, but any advice on diagnosing the problem would be welcome.

    Read the article

  • SATA-II motherboard and drives but only connected at SATA-I

    - by Shevek
    I have an Abit AB9 QuadGT motherboard which has a SATA-II controller. Connected to it I have a Kingston SSDNow V Series 64GB as boot drive and a Seagate Barracuda 7200.10 as a data drive. I also have 2 x Optiarc AD-7170S DVD burners attached by SATA. Both SSD and HDD are SATA-II and the optical drives are SATA-I. I have just run CrystalDiskInfo and this is reporting that both SSD and HDD are connected at SATA-I (1.5 Gbps), not SATA-II (3.0 Gbps). I have the BIOS set up to use SATA drives in IDE mode. So a few questions: Is CrystalDiskInfo reporting correctly? Are the optical drives causing the SSD & HDD to connect at the slower rate? Is there any setting to force the SSD & HDD to use SATA-II? I'm running Windows 7 Ultimate.

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >