Search Results

Search found 18488 results on 740 pages for 'android networking'.

Page 333/740 | < Previous Page | 329 330 331 332 333 334 335 336 337 338 339 340  | Next Page >

• Windows Server 2008 network speed slow, Xen 3.4.3 HVM ISO

  - by Elliot.Bradshaw

  I've setup a VM running Windows Server 2008 on a host node running Xen 3.4.3-5 and the following kernel: 2.6.18-308.1.1.el5xen #1 SMP Wed Mar 7 05:38:01 EST 2012 i686 i686 i386 GNU/Linux The network speed on the VM is very slow--using the online speed tests I can only get it up to 8-9mbps. The line is 100mbps burstable and the host node has no problem achieving those speeds. If it setup a VM running CentOS, it too has no problems achieving those speeds. I've done some pretty exhaustive troubleshooting, but nothing has helped: New VM installations of Win2k8 do have the same network problem. Upgrading to most recent kernel-xen did not help (2.6.18-308.1.1.el5xen). Upgrading from xen 3.4.0 to xen 3.4.3-5 did not help. Disabling Windows firewall, etc did not help. Changing network card device config from auto negotiation to manually be 100mbps full duplex did not help. Changing the network receive buffer packet size did not help (tried all combos from 64k to 8k). At this point I'm pretty much out of ideas--any help would be appreciated!

  Read the article

• Why do Ping and Dig provide different IP address than nslookup?

  - by user1032531

  When pinging my domain name which points to my home public IP from two different servers on my LAN, it shows them pinging different IP. Further investigation shows dig and nslookup providing different results. See below. A little history. My IP used to be 11.22.33.444 and is hosted by Comcast. I changed routers, and it somehow got changed to 55.66.77.888. I've since updated my 1and1 domain name to point to the 55.66.77.888. desktop is a basic server, runs the web server, and connects wirelessly to my LAN. laptop is a GUI and connected via CAT5. Both operate Centos6.4. My old router was a D-Link, and used their "Virtual Server" feature to pass port 80 to desktop. My new router is a Linksys, and I use their "Port Forwarding" feature to pass port 80 to desktop (however, I haven't gotten this part working yet). What is going on??? Why the different IPs? Obviously, it most somehow be stored on the server, but why does the actual machine even know the public IP since it is on a LAN? How do I purge the old IP? [root@desktop etc]# dig +short myDomain.com 11.22.33.444 [root@desktop etc]# nslookup www.myDomain.com Server: 8.8.8.8 Address: 8.8.8.8#53 Non-authoritative answer: Name: www.myDomain.com Address: 55.66.77.888 [root@desktop etc]# dig myDomain.com ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6_4.6 <<>> myDomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 13822 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;myDomain.com. IN A ;; ANSWER SECTION: myDomain.com. 16031 IN A 11.22.33.444 ;; Query time: 21 msec ;; SERVER: 8.8.8.8#53(8.8.8.8) ;; WHEN: Mon Oct 21 04:36:52 2013 ;; MSG SIZE rcvd: 44 [root@desktop etc]# [root@laptop ~]# dig +short myDomain.com 55.66.77.888 [root@laptop ~]# nslookup www.myDomain.com Server: 192.168.0.1 Address: 192.168.0.1#53 Non-authoritative answer: Name: www.myDomain.com Address: 55.66.77.888 [root@laptop ~]#

  Read the article

• How can ICS in Windows 7 be managed via command line, scripts, config files, etc.?

  - by Skya

  I've been using ICS successfully for years, but now I'm looking for a way to control it through something else than the GUI in Control Panel\Network and Internet\Network Connections - Connection Properties: I want to do everything that the encircled checkbox does, without touching the GUI. But what does the checkbox do? Microsoft don't provide specific information and the most helpful forum post I've found is from 2003. Assuming that some of the advice is still valid, I've come to the conclusion that ICS is broken down into 6 parts that have to be set up individually: the sharedAccess service interface settings firewall rules a static route dnsproxy autodhcp I've already learned that the service can be started/stopped with the command net start/stop sharedAccess and that netsh is a good tool for changing the interface settings and the firewall rules. But I don't understand how ICS handles routing and DNS. All hosts in my network are configured statically, so I don't care much about autodhcp. Thanks for your help! EDIT: I've spent the whole day scanning through ProcMon and I've seen reads/writes to both the registry and the filesystem and it is difficult to determine what parts of it actually make ICS work. I'm trying to look for an API instead. I'm looking into this right now, but I still want to know more about the inner workings.

  Read the article

• Problem with Macbook air automatically not acquiring free wifi network dns or router address

  - by Rumsfeld

  I have this problem when my macbook air sometimes does not connect to free wifi hotspots. When the problem happens and I try to run the diagnostics, it normally gets to yellow network settings tab. It seems that it for some reason does not acquire automatically the router or dns address. Sometimes after I shut it down and restart it magically connects to the wifi hotspot but it is very inconsistent. Anyone knows a fix for this problem?

  Read the article

• No network connectivity for my CentOS 6 installed in VMWare Fusion in MacOSX Lion

  - by gilzero

  I installed CentOS 6.2 (CentOS-6.2-x86_64-minimal.iso) with VMWare Fusion(Version 4.1.2). (Not with EasyInstall). I am using MacOSX Lion, connect to internet via WIFI. The centos installed does not have network connectivity. *How may I configure it to connect to wifi? * Thanks for any help. Below is screenshot of ifconfig: With the setting Network Adapter, I tried both NAT and Bridged WiFi.

  Read the article

• Internet Sharing via router

  - by mak4pi

  Question: How to setup Internet Sharing among two computers (one Mac 10.5.6, one Ubuntu 9.10) via a router? Situation: The Mac is using AirPort (wireless interface) to connect to router as 192.168.1.101. The Ubuntu is using an ethernet cable to connect to router as 192.168.1.104. Visual: Mac )))))) Router ======= Ubuntu Any ideas are greatly appreciated. Thanks.

  Read the article

• Server Names Inside Private Network

  - by thyandrecardoso

  Our office has a private network, where any requests on a (pre-determined) public IP are forwarded to a private IP inside said network. On that private IP, we've got a server running several services, including HTTP servers, and SCM systems. We only control our private network, having no control on the public IP configuration. We bought a domain name, and pointed it to that public IP, so people can access our services from the outside. But, when inside the office, people can't use that DNS name, because the server and any other hosts inside the network share the same public IP! For desktops, inside the office network, dealing with names is really easy: one entry on the hosts file and we're done. However, for laptops, that keep going in and out, and need to access services inside the office, the naming is really annoying. I don't know the "standard" process for dealing with these kind of situations. I've considered installing BIND in the office, and make people configure their wireless and wired connections to use that DNS server. What is the correct approach in this situation? If using BIND (or any other DNS server) is the answer, how should I configure it so that people inside the office can use it to get our custom names, and get forwarded to the ISP DNS when trying to reach the internet?

  Read the article

• allow SSH to bypass VPN on OSX mavericks, openvpn, pf

  - by zycho42

  My home computer connects to the internet through an OpenVPN connection. However, I would like to be able to connect to my home computer from outside over ssh. Ssh is set up and working, but when I connect to the vpn ssh is only accessible from inside my home network. I figure what's going wrong is my router forwards incoming ssh connections to my mac, but then my mac replies over the vpn, so the connection from outside times out. I've got pf set up for a couple of other things, but I can't figure out how to let the ssh replies bypass the vpn using pf. I've come across other solutions that use ip tables, routing tables and rules, but I can't figure out how to set that up on mavericks. I've been searching for this for a while now but I haven't found a working solution. Any help would be greatly appreciated!

  Read the article

• Spanning-tree setup with incompatible switches

  - by wfaulk

  I have a set of eight HP ProCurve 2910al-48G Ethernet switches at my datacenter that are set up in a star topology with no physical loops. I want to partially mesh the switches for redundancy and manage the loops with a spanning-tree protocol. However, our connection to the datacenter is provided by two uplinks, each to a Cisco 3750. The datacenter's switches are handling the redundant connection using PVST spanning-tree, which is a Cisco-proprietary spanning-tree implementation that my HP switches do not support. It appears that my switches are not participating in the datacenter's spanning-tree domain, but are blindly passing the BPDUs between the two switchports on my side, which enables the datacenter's switches to recognize the loop and put one of the uplinks into the Blocking state. This is somewhat supposition, but I can confirm that, while my switches say that both of the uplink ports are forwarding, only one is passing any real quantity of data. (I am assuming that I cannot get the datacenter to move away from PVST. I don't know that I'd want them to make that significant of a change anyway.) The datacenter has also sent me this output from their switches (which I have expurgated of any identifiable info): 3750G-1#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 5 (GigabitEthernet1/0/5) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 0018.73d3.yyyy Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/5 Root FWD 4 128.5 P2p Gi1/0/6 Altn BLK 4 128.6 P2p Gi1/0/8 Altn BLK 4 128.8 P2p and: 3750G-2#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 6 (GigabitEthernet1/0/6) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 000f.f71e.zzzz Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/1 Desg FWD 4 128.1 P2p Gi1/0/5 Altn BLK 4 128.5 P2p Gi1/0/6 Root FWD 4 128.6 P2p Gi1/0/8 Desg FWD 4 128.8 P2p The uplinks to my switches are on Gi1/0/8 on both of their switches. The uplink ports are configured with a single tagged VLAN. I am also using a number of other tagged VLANs in my switch infrastructure. And, to be clear, I am passing the tagged VLAN I'm receiving from the datacenter to other ports on other switches in my infrastructure. My question is: how do I configure my switches so that I can use a spanning tree protocol inside my switch infrastructure without breaking the datacenter's spanning tree that I cannot participate in?

  Read the article

• Issue with Netgear GS108T Managed Switch and Jumbo Frames

  - by Richie086

  I recently purchased a Netgear GS108T managed switch and I am trying to configure jumbo packets between my NAS (Thecus N4100Pro), PC and managed switch. I should mention the fact that I was able to use jumbo frames between my PC and NAS before I purchased the switch without issue. My Desktop has a wired gigabit NIC (Intel 82579V Gigabit) and has the ability to configure jumbo frames (see pic) that are either 9014 bytes or 4088 bytes. I choose 9014 bytes for the jumbo frame size My NAS supports jumbo frames as well, and is configured to use 9014 as the frame size. When I go into my Netgear managed switch and set the frame size to 9014 on the ports I am using for my PC and NAS. See image As soon as I hit apply in the web interface, I loose my connection to the SMB shares on my NAS and I can no longer connect to the web admin interface for my NAS. The really strange thing is I can ping my NAS via the ping command, but when I try to connect to the web interface on port 80 or port 443 the page never loads. I did a scan from my PC to my NAS using nmap and I can see the following ports open PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 111/tcp open rpcbind 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 631/tcp open ipp 2000/tcp open cisco-sccp 2049/tcp open nfs 3260/tcp open iscsi 49152/tcp open unknown MAC Address: 00:14:FD:15:00:44 (Thecus Technology) Read data files from: C:\Program Files (x86)\Nmap Nmap done: 1 IP address (1 host up) scanned in 211.97 seconds Raw packets sent: 1 (28B) | Rcvd: 1 (28B) Anyone have any idea what is going on here? Why is nmap able to detect the ports are open and listening for http, https and file sharing but I cant connect when all devices have jumbo packets enabled? Stranger still - I did a packet capture using wireshark while the nmap scan was running and filtered so I only saw converstations between my PC and my NAS. Here are the packet details from my scan Only 4 packets over 5k bytes? What is going on here? Do I not need to configure jumbo frame sizes on the switch? I have an internet connection from my pc to the switch to my router - I just cannot connect to my NAS. I just checked on my iPhone and I am able to open my NAS web admin interface without issue on my iPhone! WTF!!!!!! Let me know if you need more details..

  Read the article

• How to install ZTE AC2726 on Karmic Koala

  - by Ravi Gupta

  I just got a ZTE AC2726 wireless broadband device for my Karmic Koala but I am not able install it as the vendor has given drivers for Jaunty and not Karmic. How do I go about it?

  Read the article

• Finding wireless interference, on Mac

  - by Cawas

  Based on another similar question, what are good software and hardware options for "finding wireless interference" for the apple?

  Read the article

• Should I remove all unmanged switches from my network?

  - by IMAbev

  I have a office network with approx 150 devices (computers/printers/ip phones). Almost all of the end point devices have straight run Cat5e from my Hp switches directly to the device. IP phones for each end user sit between the hp switch and computer. (hp switch - in to phone out of phone in to computer) While I have gotten rid of most of them, I still have a couple linksys unmanaged switches that split off to 2 or more devices. I have heard various reasons for removing these switches but not entirely sure if it actually degrades the network. I agree that eliminating these switches certainly cleans up the network from a management standpoint. Are these unmanaged switches bad for my network? Is there a clear advantage to having 'home run' cable runs to each of my end point devices?

  Read the article

• CPU & Memory Usage Log & Performance

  - by wittythotha

  I want to have an idea of the amount of CPU and memory that is being used. I have a website hosted using IIS, and have clients connecting to it. I want to find out the amount of load that the CPU, RAM and the network has when multiple clients connect. I tried out using tools like Fiddler, the inbuilt Resource Manager, and also some other applications I found on the internet. I just want to keep track of all these data in a file, so I can plot out a graph and find out how the CPU, etc. is performing. I read a few other posts, but didn't find anything that solves the problem. Is there good CPU / Memory Logging tool available, just to plot a graph of the usage, etc.? EDIT : I want to know of some tool that can save the performance details in a log file, so that I can use it to plot a graph, etc.

  Read the article

• Windows 7 - system error 5 problem

  - by Ian

  My wife has just had a new computer for Christmas (with an upgrade from VISTA to Windows 7), and has joined the home network. We are using a mix of WindowsXP and Ubuntu boxes linked via a switch. We are all in the same workgroup. (No domain). Internet access, DHCP, and DNS server is an SME server that thinks it is domain controller (although we are not using a domain). I need to run a script to back up my wife's machine (venus). In the past the script creates a share on a machine with lots of space (leda), and then executes the line. PSEXEC \\venus -u admin -p adminpassword -c -f d:\Progs\snapshot.exe C: \\leda\Venus\C-drive.SNA With the wife's old XP machine, this would run the sysinternals utility, copy shapshot,exe to her machine and run it, which would then back up her C: drive to the share on leda. I cannot get this to work with Windows 7, nor can I link through to the C$ share on her machine. This gives me a permissions error (system error 5). The admin account is a full admin account. And yes - I do know the password. The ordinary shares on her machine work fine! I guess I'm missing something that Microsoft have built into Windows 7 - but what? The machine is running Windows 7 business, with windows firewall, AVG anti virus, and all the crap-ware you get with a new PC removed. Thanks

  Read the article

• Log centralization, display, transport and aggregation at scale v2

  - by Eric DANNIELOU

  This is a duplicate question of Log transport and aggregation at scale and http://stackoverflow.com/questions/1737693/whats-the-best-practice-for-centralised-logging, but the answers might differ now : The softwares described in 2009 may have changed since (for example Octopussy evolved from version 0.9 to 1.0.5). Rsyslog has become the default on most linux distro. Requirements have changed (security, software configuration management, ...). I'd like to ask the following questions : How do you centralize, display and archive system logs? How would you like to do it now if you had to? Most linux distro use rsyslog nowadays, which can provide reliable log transport. But some older unices, network devices and maybe windows box still use old udp rfc-style transport. How did you manage to get reliable transport? Storing logs for a few months can represent a huge amount of disk space. How do you store them? rdbms? Compressed and encrypted text files?

  Read the article

• Windows XP Network installation from Linux server ( RHEL 5)

  - by Kumar P

  How can i make network installation ( for install Windows XP ) from Linux ( RHEL 5 Server ) ? There is option in linux server to install client machine with linux by network installation. As same as windows server have option to install client machine with windows operating system. Now i want to know steps for linux server (RHEL5) to install client machine with windows operating system (Windows XP) *sorry for poor english

  Read the article

• Can't connect to wireless router anymore due to data rate problem

  - by Jay White

  I was playing around with my wireless router, and switched the mode to a fixed mode B. Now< I can no longer assoicate to the AP. Windows does not give any particular error message, but with wireshark I see that the returned error is that the client does not support the necessary data rate. My wireless card is type n, and it is set to mode a/b/g compatible. I tried setting ot to just b, however this made no difference. How can I set the data rate of my card so that I can connect again to my AP? I would prefer not to just reset the device, as there has been some configuration done that would be a pain to redo, and as well I do not have the ISP password handy. Regardless I would like to understand this situation better.

  Read the article

• Block P2P traffic on a Linksys router WRT54G with tomato firmware

  - by Kami

  Hi, I'm running a small wireless network (6 to 10 users) on a Lynksys WRT54G with tomato firmware sharing an internet connection. I don't want the users to download files with bittorrent (mainly used) and other p2p apps. I've also found some solutions about lowering p2p traffic priority using QoS. I really need to BAN p2p traffic. Does anyone know how to setup some rules to deny that kind of traffic ? I've tried to setup an Access Restriction Rule: But it's not working at all ...

  Read the article

• MacBook's Airport not working from menu bar

  - by not22

  All of the sudden my MacBook doesn't connect to my wireless after waking from sleep. My network shows up at full signal strength and it remembers the password correctly, but I get an error message when I try to connect from the menu bar. The only way I can get on the internet is to go through Network Diagnostics and turn it on there. I don't understand why it works every time through Network Diagnostics and never on it's own or through the airport menu bar. Nothing has been changed or installed or reset on my computer that I know of. Restarting doesn't fix it, nor does turning off the airport card. Any ideas?

  Read the article

• Router stopping my python server

  - by drfrev

  This was originally posted in stackoverflow.com but it was suggested I move it here after it was realized it wasn't my code that was wrong. So my problem, very simply, is that I cannot get my computers that are connected to my router to communicate. example: If I ping a wireless computer I get no responce and the Request times out If I ping a computer wired to the modem directly it works fine. When I ping I use the local ip for each case. *if it helps my original post is here: http://stackoverflow.com/questions/12593024/python-cannot-go-over-internet-network/12593361#12593361 And some screen shots of different things are here: http://imgur.com/a/jUZ4G#3 thank you, any help is greatly appreciated. NOTE I am heading off to bed now, so I will respond around 6:00 AM EST if anyone posts some help

  Read the article

• IP route ppp0 + eth0 access to outside network

  - by Vitor

  I need some help in define a route I have two connections one from eth0 and other a ppp0 (a 3G card) Not having the ppp0 connection active my route table is: Destination Gateway Genmask Flags Metric Ref Use Iface default DD-WRT 0.0.0.0 UG 100 0 0 eth0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 I can access my webserver from an outside network through ethernet interface Than I have also my ppp0 3G connection active havig the following route table: D estination Gateway Genmask Flags Metric Ref Use Iface default 10.64.64.64 0.0.0.0 UG 0 0 0 ppp0 10.64.64.64 * 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 Now I only can access my webserver in outside networks through the IP of the 3G connection Note that my server is serving at 0.0.0.0 IP (to all interfaces) But I need to get access to webserver to both interfaces ethernet and 3G connection I only can have access to both connection in local network Any help to configure this network to have both interfaces with outside networks access is welcome Can anyone give me an example to configure this network with 2 gateways to give outside networks access One for IP 192.168.1.149 and other for the ppp0 IP 89.214.60.196 Tanks

  Read the article

• Cisco VPN disconnects after 5 seconds with error 422

  - by Marius

  I'm trying to connect to my university's server with VPN using Cisco VPN Client version 5.0.04, but after 5 seconds it disconnects with the error message 422: Lost contact with the secure gateway. Check your connection. From my research on the net it seems this could be because it tries to find my IP, and finds out that this is 127.0.0.1. Then 5 seconds later it discovers that I have a new IP (my actual IP), and it disconnects because I'm not allowed to change IP. Does anyone know how I could fix this, or if there is another reason i get this error? Update I looked through the log, and found this error, which confirms what I thought, except it gets the correct IP first, then changes it to localhost. 87 18:56:53.250 08/24/09 Sev=Warning/3 CM/0xA3100027 Adapter address changed from 149.171.237.25. Current address(es): 127.0.0.1.

  Read the article

• cisco 6500 crash enabling netflow

  - by bleomycin

  Hello everyone, i have a cisco 6503 running IOS 12.2(33)sxi5 and i'm trying to enable netflow. Following the instructions here http://www.manageengine.com/products/netflow/help/cisco-netflow/cisco-ios-netflow.html enabling for interface vlan 3, shortly after ip flow-export version 5 console outputs: CPU_MONITOR-6-NOT_HEARD: CPU monitor messages have not been heard for 30 seconds crashlog here: http://pastebin.com/Niv2H8xD it then writes a crash log and reloads the router. Has anyone else experienced anything like this before? Here is my running config prior to adding the options in the above link: http://pastebin.com/AgNb1ahG Thank you for any help!

  Read the article

• Mac OS X: network disabled because security breach

  - by fireeyedboy

  Dear all, I just recieved a message on my Mac OS X system telling me (loosely translated from Dutch): "The network has been temporarily disabled because the network's security was breached." (It's a wireless WPA2-PSK secured network BTW) I looked in the logs of my router (a Zyxel P-2602HW-D1A) only to see a few (outbound) "syn flood TCP ATTACK" logs, but those were from like a week ago, other than that nothing. What tools on Mac OS X do I have to analyse this security breach occurence? Are there some security logs on Mac OS X that I can inspect? What other measurements should I take? And how serious should I take this warning from Mac OS X? System: Macbook Pro Intel Core 2 Duo 2.2 Ghz OS: Mac OS X 10.5.8 Network: wireless WPA2-PSK Relevant software: Parallels Desktop with Windows XP (was open, but stopped at the time) Other systems on my network: Windows XP SP3 desktop (was running at the time) If you need any more info, don't hestitate to ask. Thanks in advance.

  Read the article

< Previous Page | 329 330 331 332 333 334 335 336 337 338 339 340  | Next Page >