Search Results

Search found 12726 results on 510 pages for 'compatibility mode'.

Page 455/510 | < Previous Page | 451 452 453 454 455 456 457 458 459 460 461 462  | Next Page >

  • How do I troubleshoot an IPsec tunnel (from a cellular router to a public server)?

    - by Hanno Fietz
    I'm new to IPsec and struggling with a setup that might soon be widely used in our operations (provided I do understand it, eventually...). A cellular router (blackbox by netModule, from its log messages it seems to be running Linux and OpenSwan) connects a sensor network on customers' sites with our public server. We need to be able to connect into the local network, so I had the cell provider give me a public IP (a dynamic one). The way their setup works, the public IPs only allow IPsec traffic. I set up OpenSwan on our Ubuntu server (running Jaunty). This is my connection config from /etc/ipsec.conf: conn gprs-field-devices left=my.pub.lic.ip [email protected] #leftsubnet=192.168.1.129/25 right=%any [email protected] #rightsubnet=192.168.1.1/25 #rightnexthop=%defaultroute auto=add On the router, all I have is the Web UI, in which I made the following settings: "Remote endpoint": public IP of server, same as "left" above "Local Network Address": 192.168.1.1 "Local Network Mask": 255.255.255.128 "Remote Network Address": 192.168.1.129 "Remote Network Mask": 255.255.255.128 The pluto process on the server is listening for connections on port 500. It can't open a tunnel, obviously, because it doesn't know at which IP the client is. I set up a passphrase as PSK for @field.econemon.com in /etc/ipsec.secrets and also configured it in the router (which doesn't seem to support certificates). My problem is, nothing happens. The router just says, IPsec is "down". When I copy-paste the IP into ipsec.conf (for "right="), and ask the server to ipsec auto --up gprs-field-devices, it just hangs until I press Ctrl-C. Is there anything wrong with my setup? How can I debug this further? My router gives the following loglines that seem related, but don't tell me anything: Feb 21 23:08:20 Netbox authpriv.warn pluto[2497]: loading secrets from "/etc/ipsec.secrets" Feb 21 23:08:20 Netbox authpriv.warn pluto[2497]: loading secrets from "/etc/ipsec.d/hostkey.secrets" Feb 21 23:08:20 Netbox authpriv.warn pluto[2497]: loading secrets from "/etc/ipsec.d/netbox0.secrets" Feb 21 23:08:20 Netbox authpriv.warn pluto[2497]: "netbox00" #1: initiating Main Mode Feb 21 23:08:20 Netbox daemon.err ipsec__plutorun: 104 "netbox00" #1: STATE_MAIN_I1: initiate Feb 21 23:08:20 Netbox daemon.err ipsec__plutorun: ...could not start conn "netbox00" Feb 21 23:08:22 Netbox authpriv.warn pluto[2497]: packet from 188.40.57.4:500: ignoring informational payload, type NO_PROPOSAL_CHOSEN Feb 21 23:08:22 Netbox authpriv.warn pluto[2497]: packet from 188.40.57.4:500: received and ignored informational message Feb 21 23:08:28 Netbox user.warn parrot.system_controller[762]: IPSECCTRLR: Tunnel 0 is down for 0 seconds Feb 21 23:08:40 Netbox user.warn parrot.system_controller[762]: IPSECCTRLR: Tunnel 0 is down for 10 seconds Feb 21 23:08:52 Netbox authpriv.warn pluto[2497]: packet from 188.40.57.4:500: ignoring informational payload, type NO_PROPOSAL_CHOSEN

    Read the article

  • Why many applications close after opening a document or doing a specific actions?

    - by Mohsen Farjami
    I have some encrypted pdf files that have no problem and in my last windows, I could open them easily with Adobe Reader 9.2 and other pdf readers. But now, I can only open non-encrypted pdf files and one encrypted file with Adobe Reader. every time I open almost any encrypted pdf, it closes itself. Also, when I try to search a folder for a keyword with Foxit Reader, once it closed. This is not related to Adobe Reader, because I have the same problem with Word 2007. When I open a document, sometimes it closes instantly and sometimes it closes after a few seconds and sometimes it is stable. My windows is Fresh. I have installed it a few days ago. I have ESET Smart Security 5.2 and I have updated it today. OS: XP Pro SP3, RAM: 3 GB, CPU: 2 GHZ, HDD: 320 GB My installed applications: Adobe AIR Adobe Flash Player 11 ActiveX Adobe Flash Player 11 Plugin Adobe Photoshop CS4 Adobe Reader 9.2 Atheros Wireless LAN Client Adapter Babylon Bluetooth Stack for Windows by Toshiba CCleaner Conexant HD Audio Dell Touchpad ESET Smart Security Farsi (101) Custom Foxit Reader Framing Studio 3.27 Google Chrome Hard Disk Sentinel PRO HDAUDIO Soft Data Fax Modem with SmartCP Intel(R) Graphics Media Accelerator Driver IrfanView (remove only) Java(TM) 6 Update 18 K-Lite Mega Codec Pack 8.8.0 Microsoft .NET Framework 2.0 Service Pack 1 Microsoft .NET Framework 3.0 Service Pack 1 Microsoft .NET Framework 3.5 Microsoft Data Access Components KB870669 Microsoft Office 2007 Primary Interop Assemblies Microsoft Office Enterprise 2007 Microsoft User-Mode Driver Framework Feature Pack 1.0.0 (Pre-Release 5348) Mozilla Firefox 7.0.1 (x86 en-US) Notepad++ Office Tab FreeEdition 8.50 ParsQuran PerfectDisk 12 Professional Registry First Aid RICOH R5C83x/84x Flash Media Controller Driver Ver.3.54.06 Sahar Money Manager 2.5 Stickies 7.1d The KMPlayer (remove only) TurboLaunch 5.1.2 Unlocker 1.9.1 USB Safely Remove 4.2 Virastyar Visual Studio 2005 Tools for Office Second Edition Runtime Winamp Windows Internet Explorer 8 Windows Media Player 11.0.5358.4826 Windows XP Service Pack 3 WinRAR 4.11 (32-bit) WorkPause 1.2 Z Dictionary My startup applications: WorkPause USB Safely Remove TurboLaunch SunJavaUpdateSched Stickies rfagent Persistence ParsQuran Daily Verse ITSecMng IgfxTray HotKeysCmds Hard Disk Sentinel egui disable shift+delete CTFMON.EXE Bluetooth Manager Babylon Client Apoint AdobeCS4ServiceManager Adobe Reader Speed Launcher Adobe ARM What should I do to solve it? If you recommend installing Windows again, what guarantees that it won't happen again?

    Read the article

  • Corosync :: Restarting some resources after Lan connectivity issue

    - by moebius_eye
    I am currently looking into corosync to build a two-node cluster. So, I've got it working fine, and it does what I want to do, which is: Lost connectivity between the two nodes gives the first node '10node' both Failover Wan IPs. (aka resources WanCluster100 and WanCluster101 ) '11node' does nothing. He "thinks" he still has his Failover Wan IP. (aka WanCluster101) But it doesn't do this: '11node' should restart the WanCluster101 resource when the connectivity with the other node is back. This is to prevent a condition where node10 simply dies (and thus does not get 11node's Failover Wan IP), resulting in a situation where none of the nodes have 10node's failover IP because 10node is down 11node has "given back" his failover Wan IP. Here's the current configuration I'm working on. node 10sch \ attributes standby="off" node 11sch \ attributes standby="off" primitive LanCluster100 ocf:heartbeat:IPaddr2 \ params ip="172.25.0.100" cidr_netmask="32" nic="eth3" \ op monitor interval="10s" \ meta is-managed="true" target-role="Started" primitive LanCluster101 ocf:heartbeat:IPaddr2 \ params ip="172.25.0.101" cidr_netmask="32" nic="eth3" \ op monitor interval="10s" \ meta is-managed="true" target-role="Started" primitive Ping100 ocf:pacemaker:ping \ params host_list="192.0.2.1" multiplier="500" dampen="15s" \ op monitor interval="5s" \ meta target-role="Started" primitive Ping101 ocf:pacemaker:ping \ params host_list="192.0.2.1" multiplier="500" dampen="15s" \ op monitor interval="5s" \ meta target-role="Started" primitive WanCluster100 ocf:heartbeat:IPaddr2 \ params ip="192.0.2.100" cidr_netmask="32" nic="eth2" \ op monitor interval="10s" \ meta target-role="Started" primitive WanCluster101 ocf:heartbeat:IPaddr2 \ params ip="192.0.2.101" cidr_netmask="32" nic="eth2" \ op monitor interval="10s" \ meta target-role="Started" primitive Website0 ocf:heartbeat:apache \ params configfile="/etc/apache2/apache2.conf" options="-DSSL" \ operations $id="Website-one" \ op start interval="0" timeout="40" \ op stop interval="0" timeout="60" \ op monitor interval="10" timeout="120" start-delay="0" statusurl="http://127.0.0.1/server-status/" \ meta target-role="Started" primitive Website1 ocf:heartbeat:apache \ params configfile="/etc/apache2/apache2.conf.1" options="-DSSL" \ operations $id="Website-two" \ op start interval="0" timeout="40" \ op stop interval="0" timeout="60" \ op monitor interval="10" timeout="120" start-delay="0" statusurl="http://127.0.0.1/server-status/" \ meta target-role="Started" group All100 WanCluster100 LanCluster100 group All101 WanCluster101 LanCluster101 location AlwaysPing100WithNode10 Ping100 \ rule $id="AlWaysPing100WithNode10-rule" inf: #uname eq 10sch location AlwaysPing101WithNode11 Ping101 \ rule $id="AlWaysPing101WithNode11-rule" inf: #uname eq 11sch location NeverLan100WithNode11 LanCluster100 \ rule $id="RAND1083308" -inf: #uname eq 11sch location NeverPing100WithNode11 Ping100 \ rule $id="NeverPing100WithNode11-rule" -inf: #uname eq 11sch location NeverPing101WithNode10 Ping101 \ rule $id="NeverPing101WithNode10-rule" -inf: #uname eq 10sch location Website0NeedsConnectivity Website0 \ rule $id="Website0NeedsConnectivity-rule" -inf: not_defined pingd or pingd lte 0 location Website1NeedsConnectivity Website1 \ rule $id="Website1NeedsConnectivity-rule" -inf: not_defined pingd or pingd lte 0 colocation Never -inf: LanCluster101 LanCluster100 colocation Never2 -inf: WanCluster100 LanCluster101 colocation NeverBothWebsitesTogether -inf: Website0 Website1 property $id="cib-bootstrap-options" \ dc-version="1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1408954702" \ maintenance-mode="false" rsc_defaults $id="rsc-options" \ resource-stickiness="100" \ migration-threshold="3" I also have a less important question concerning this line: colocation NeverBothLans -inf: LanCluster101 LanCluster100 How do I tell it that this collocation only applies to '11node'.

    Read the article

  • Ubuntu 12.04 crash analysis - strange binary data on all open files at the moment of crash

    - by lanbo
    A couple of hours ago we got a system crash on Ubuntu 12.04. We checked all the log files and there is nothing suspicious to blame to. Last stuff that was logged was some dovecot activity. There are no kernel panic messages. Nothing. It is a new server (new hardware) we are testing before production. And because it is new hard, I'm suspicious the problem may be due to some faulty hardware. We already run memtester with no problem detected. I'll be happy to hear from other hardware testing tools (the machine has SSD). Anyway, the thing I wanted to ask you is a different one. The strange thing is on every open file at the moment of the crash we found the next sequence of symbols was written into them: "@^@^@^@^@^@^@...". For example, on the syslog log file we got: Apr 16 15:53:56 odyssey dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<info>, method=PLAIN, rip=46.29.255.73, lip=5.9.58.177 ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^ [these continues for about 1000 chars...] ^@^@^@^@Apr 16 15:55:12 odyssey kernel: imklog 5.8.6, log source = /proc/kmsg started. We got all these symbols in all open files. These include: syslog, mail.log, kern.log, ... But also on some logs that are output by php scripts run in CRONs from user accounts (not root). So, any idea why all open files got these characters written during the crash? This is pretty bad since the crash corrupted many files (we don't even know which other ones may be affected). We are suspicious that all open files (in write mode maybe) at the moment of the crash got all these symbols inserted. Why is that? BTW [in case it helps], the system automatically rebooted after the crash but Apache did not start. There were not traces in /var/apache2/*log why apache did not start. After running a "service apache2 start" it started with no problems. Also, we rebooted the machine manually and Apache also started on reboot. But it did not start after the crash and no errors were reported. Thanks guys!

    Read the article

  • How to get an inactive RAID device working again?

    - by Jonik
    After booting, my RAID1 device (/dev/md_d0 *) sometimes goes in some funny state and I cannot mount it. * Originally I created /dev/md0 but it has somehow changed itself into /dev/md_d0. # mount /opt mount: wrong fs type, bad option, bad superblock on /dev/md_d0, missing codepage or helper program, or other error (could this be the IDE device where you in fact use ide-scsi so that sr0 or sda or so is needed?) In some cases useful info is found in syslog - try dmesg | tail or so The RAID device appears to be inactive somehow: # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md_d0 : inactive sda4[0](S) 241095104 blocks # mdadm --detail /dev/md_d0 mdadm: md device /dev/md_d0 does not appear to be active. Question is, how to make the device active again (using mdmadm, I presume)? (Other times it's alright (active) after boot, and I can mount it manually without problems. But it still won't mount automatically even though I have it in /etc/fstab: /dev/md_d0 /opt ext4 defaults 0 0 So a bonus question: what should I do to make the RAID device automatically mount at /opt at boot time?) This is an Ubuntu 9.10 workstation. Background info about my RAID setup in this question. Edit: My /etc/mdadm/mdadm.conf looks like this. I've never touched this file, at least by hand. # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR <my mail address> # definitions of existing MD arrays # This file was auto-generated on Wed, 27 Jan 2010 17:14:36 +0200 In /proc/partitions the last entry is md_d0 at least now, after reboot, when the device happens to be active again. (I'm not sure if it would be the same when it's inactive.) Resolution: as Jimmy Hedman suggested, I took the output of mdadm --examine --scan: ARRAY /dev/md0 level=raid1 num-devices=2 UUID=de8fbd92[...] and added it in /etc/mdadm/mdadm.conf, which seems to have fixed the main problem. After changing /etc/fstab to use /dev/md0 again (instead of /dev/md_d0), the RAID device also gets automatically mounted!

    Read the article

  • Postfix to deliver mail to a virtual address mailbox

    - by Chloe
    Postfix version 2.6.6, Dovecot Version 2.0.9 I want to setup Postfix + Dovecot. Dovecot seems to be working. I can authenticate. However, the mailbox is empty! Nothing will get delivered! I followed many tutorials on Postfix + Dovecot but they seem to want to complicate things by using Dovecot LDA or MySQL. I just want it to be very simple and having Postfix deliver to the virtual mail boxes are fine. I don't need MySQL either. I already set up a custom password file that Dovecot uses for authentication and I can login to POP3 with SSL. I can see from the logs that Postfix is delivering to the system user accounts (the catch-all), instead of the virtual users that I set up in Dovecot. The SMTP + SSL authentication seems to work also. I can also see from the logs that Dovecot is checking the correct virtual mail folder. I just need to figure out how to get Postfix to deliver to the virtual mail boxes. I have the following which I believe are relevant. Let me know what other settings you need to see: alias_maps = hash:/etc/aliases mydestination = $myhostname, localhost.$mydomain, localhost, $mydomain mydomain = xxx.com myhostname = mail.xxx.com mynetworks = 99.99.99.99, 99.99.99.99 myorigin = $mydomain relay_domains = $mydestination, xxx.com, domain2.net, domain3.com sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtpd_recipient_restrictions = reject_non_fqdn_sender reject_non_fqdn_recipient reject_unknown_recipient_domain permit_sasl_authenticated check_relay_domains smtpd_sasl_auth_enable = yes smtpd_sasl_path = private/auth smtpd_sasl_type = dovecot smtpd_sender_restrictions = check_sender_mx_access cidr:/etc/postfix/bogus_mx reject_invalid_hostname reject_unknown_sender_domain reject_non_fqdn_sender virtual_mailbox_base = /var/spool/vmail virtual_mailbox_domains = xxx.com, domain2.net, domain3.com virtual_minimum_uid = 444 Postfix master.cf: submission inet n - - - - smtpd -o smtpd_tls_security_level=encrypt -o smtpd_sasl_auth_enable=yes -o smtpd_sasl_type=dovecot -o smtpd_sasl_path=private/auth -o smtpd_sasl_security_options=noanonymous -o smtpd_sasl_local_domain=$myhostname -o smtpd_client_restrictions=permit_sasl_authenticated,reject -o smtpd_sender_login_maps=hash:/etc/postfix/virtual -o smtpd_sender_restrictions=reject_sender_login_mismatch -o smtpd_recipient_restrictions=reject_non_fqdn_recipient,reject_unknown_recipient_domain,permit_sasl_authenticated,reject Dovecot related: mail_location = maildir:~/Maildir passdb { args = /etc/dovecot/users.conf driver = passwd-file } service auth { unix_listener /var/spool/postfix/private/auth { mode = 0660 user = postfix } } The virtual mail user: vmail:x:444:99:virtual mail users:/var/spool/vmail:/sbin/nologin Here is the /var/log/maillog when I try to send something to myself: Oct 25 22:10:05 308321 postfix/smtpd[2200]: connect from user-999.cable.mindspring.com[99.99.99.99] Oct 25 22:10:05 308321 postfix/smtpd[2200]: D224BD4753: client=user-999.cable.mindspring.com[99.99.99.99], sasl_method=LOGIN, [email protected] Oct 25 22:10:06 308321 postfix/cleanup[2207]: D224BD4753: message-id=<7DC3C163CFFC483AB6226F8D3D9969D2@dumbopc> Oct 25 22:10:06 308321 postfix/qmgr[2168]: D224BD4753: from=<[email protected]>, size=1385, nrcpt=1 (queue active) Oct 25 22:10:06 308321 postfix/smtpd[2200]: disconnect from user-999.cable.mindspring.com[99.99.99.99] Oct 25 22:10:06 308321 postfix/local[2208]: D224BD4753: to=<[email protected]>, orig_to=<[email protected]>, relay=local, delay=1.1, delays=0.53/0.02/0/0.51, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 22:10:06 308321 postfix/qmgr[2168]: D224BD4753: removed

    Read the article

  • Cannot install grub to RAID1 (md0)

    - by Andrew Answer
    I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

    Read the article

  • Google Chrome issues

    - by Ben Hooper
    I'm an avid user of Chrome and would defend it to the death but there is no denying that it has issues, and I've been experiencing a lot of them recently. Issues Stuck tabs Issue: Around 60% of the time (higher when the system has just started), when Chrome is launched, some or all of the pinned tabs and startup pages will get stuck in the counter-clockwise-rotating "contacting server" mode and never snap out of it. Fix: Quit and launch Chrome until they load properly (this really isn't good, as quitting and launching Chrome can and has cleared all pinned tabs). Extra Information: If you stop the loading and re-enter the URL then the page will load perfectly. The amount of pinned tabs or startup pages seems to be irrelevant, but I could be wrong.   "Downloaded/out of" Issue: Each item in the download bar has a downloaded status section, formatted as "downloaded/out of". Sometimes Chrome doesn't display the "out of" part.   Collapsed settings windows Issue: In Chrome version 19(ish)+, settings are configured via overlayed / popup windows. Sometimes, the window will open fully collapsed. Fix: Resize Chrome's window or open the developer tools. "Network Error" with large downloads Issue: Sometimes, when downloading large files (500MB+) Chrome will download the entire file, the download status will freeze (for example, "1 GB/1 GB") for a few minutes, report "Network error", and delete the .crdownload file. Extra Information: The same file from the same website on the same computer downloads perfectly in other browsers. The website and file type seem to be irrelevant.   Information: I've experienced some of these issues on my home PC and some on my work PC, both of which are Windows 7 Ultimate x64. The only things that link them are my Google account (all settings are synced). Updating Chrome hasn't worked. Most of these issues presented themselves around about version 17 and have continued right through to 21 (current). Uninstalling Chrome, deleting all data in %programFiles(x86)%\Google and %localAppData%\Google, and reinstalling hasn't worked. I have yet to see whether disabling all extensions would make a difference, but it's hard to diagnose as these issues don't occur 100% of the time.   In my case, I don't know if there's an actual solution. I'm just curious as to whether anyone else is having similar issues to those that I'm experiencing. At least then I'll know it's an issue with Chrome itself.

    Read the article

  • Server 2008/Windows 7/Samba Unspecified error 80004005

    - by ancillary
    I have a Samba share on a LAN with 2008 PDC/DNS. Smb authenticates with AD and I have several Win7 Machines that can connect fine. I recently added a couple of new computers to the LAN which were imaged the same way (same software, etc.; different hardware so different drivers) as the other machines and they have the same policies set. I can not get the new machines to connect to the samba share no matter what. I am always met with either Unspecified Error 0x80004005 or Network Path not found. I've turned off the firewall; set LANMAN auth to respond to NTLM only/send LM & NTLM responses/use NTLM session security if negotiated in Local Sec Policy SEcurity Options; tried both ip and hostname to connect. SMB log shows that authentication succeeds; but then connection is immediately killed by the client. tcpdump shows nothing remarkable except that when trying to connect from the client via hostname there is an unknown packet type error: ack 201 win 255 NBT Session Packet: Unknown packet type 0xABData: (41 bytes) Here's a couple of lines from that error: 11:18:37.964991 IP 001-client.domain.local.49372 > smb.domain.local.netbios-ssn: P 1670:2146(476) ack 201 win 255 NBT Session Packet: Unknown packet type 0xABData: (41 bytes) [000] AA 46 96 FA D5 99 33 75 0C C4 20 CE 26 42 F3 61 \252F\226\372\325\2313u \014\304 \316&B\363a [010] F0 8C FB 65 18 17 40 A5 DB 42 BB 94 37 53 92 EC \360\214\373e\030\027@\245 \333B\273\2247S\222\354 [020] 55 98 7F C4 AE 3D 6B 10 C4 U\230\177\304\256=k\020 \304 11:18:37.964998 IP smb.domain.local.netbios-ssn > 001-client.domain.local.49372: . ack 2146 win 100 Here's smb.conf just in case (though don't see how if other machines are working fine): [global] workgroup = MYDOMAIN realm = MYDOMAIN.LOCAL server string = domain|smb share interfaces = eth1 security = ADS password server = 192.168.1.3 log level = 2 log file = /var/log/samba/%m.log smb ports = 139 strict locking = no load printers = No local master = No domain master = No wins server = 192.168.1.3 wins support = Yes idmap uid = 500-10000000 idmap gid = 500-10000000 winbind separator = + winbind enum users = Yes winbind enum groups = Yes winbind use default domain = Yes [samba-share1] comment = SMB Share path = /home/share/smb/ valid users = @"MYDOMAIN+Domain Users" admin users = @"MYDOMAIN+Domain Admins" guest ok = no read only = No create mask = 0765 force directory mode = 0777 Any ideas what else I could try or look for? Or what might be the problem? Thanks.

    Read the article

  • file corruption on read/write 2.6.32-22-server (happens across many kernels)

    - by Jonathan
    Hi Guys, I'm having an issue where after the server has been up for a period of time (~week/few days) the server will start reading corrupt data. For instance when I run a sha1sum of a file after a fresh boot it remains the same. However after a while I will start to get segfaults and from then on whenever I read this file I get a different sha1sum. I've checked S.M.A.R.T with long tests and I've run an extended memtest86+(12 passes) My lspci is as follows: 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3300 Graphics 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller 02:00.0 Ethernet controller: Atheros Communications Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. Device 3403 I could really use some help on this, do you have any idea what could cause this? It's really frustrating me as it seems to trigger entirely randomly and will not go away until I reboot. I'm also use KVM for virtualization as well as MD for software RAID on this server and the processor is a Phenom II X4 965. I don't believe it's the software raid however as this affects files also hosted on non-raid partitions so I don't know.

    Read the article

  • In search of a good audio player for Ubuntu 9.10

    - by Joe Casadonte
    If this should be marked Community Wiki, please let me know. I'm switching from XP to Ubuntu, and I have been very disappointed with the selection of media players available. I'm primarily interested in an audio player, but integrated video and library management is OK, too. My criteria: Must be able to play audio CDs (I'm shocked how many apps this does away with, right away) Must be able to play MP3 & WAV; OGG, SHN, FLAC are all bonuses Repeat and Shuffle modes are a must FreeDB / GraceNote through a proxy is a must (if it can read a PAC file, that would be awesome) It needs to be really small, e.g. skinnable or an applet Ability to execute a playlist is a plus Gapless MP3 playback a plus I'm running Gnome, but I'm not totally adverse to a KDE app. Command-line only is also a viable option. Some that I've tried: RhythmBox - probably the best of the lot that I've tried; I don't like its mini mode (doesn't show the song being played) and I can't figure out how to get it to hit FreeDB/GraceNote through a proxy Songbird - can't play CDs, playlist management is atrocious Banshee Jajuk Maybe a couple of more. Thanks! UPDATE I tried out VLC, Amarok and Songbord (again). VLC I eventually got to work (I had some kind of bad configuration). It seemed way more involved than I was looking for out of a music player, and in general more geared to video than audio. I couldn't fathom its library management, which I think it has; maybe it doesn't, and that's why I couldn't figure it out. Amaork looked very promising but the library management was not to my liking, and the way it handled a playlist with both MP3 and WAV is inexplicable at best. I did like some aspects of the UI, but not enough to keep it. Songbird is very finicky, but I like the library management. Sort of. It kept telling me my Watch folder was invalid, even thought it clearly was accessible. Playlist management is bizarre, and the message that it was deleting source files whenever I deleted a playlist had me too worried to keep using it. Had it been able to play CDs, maybe I would have persevered. Audacious, while a bit odd at times, does seem to do what I want. If it had a library manager, I wouldn't have bothered trying any of the others. Thanks for the help, everyone!

    Read the article

  • Linksys WiFi usb dongle and linux woes

    - by MrStatic
    I have a Linksys WUSB54GC usb dongle and I have exhausted every thing I know about making this thing work in linux. I am using Fedora 13. Since it is not ready I can not view any networks. Any ideas would be great. tail of the system log Jun 2 20:14:35 localhost kernel: usb 1-7: new high speed USB device using ehci_hcd and address 8 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device found, idVendor=1737, idProduct=0077 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 2 20:14:35 localhost kernel: usb 1-7: Product: 802.11 g WLAN Jun 2 20:14:35 localhost kernel: usb 1-7: Manufacturer: Ralink Jun 2 20:14:35 localhost kernel: usb 1-7: SerialNumber: 1.0 Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::radio Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::assoc Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::quality Jun 2 20:14:35 localhost NetworkManager[1367]: <info> found WiFi radio killswitch rfkill3 (at /sys/devices/pci0000:00/0000:00:1d.7/usb1/1-7/1-7:1.0/ieee80211/phy3/rfkill3) (driver <unknown>) Jun 2 20:14:35 localhost kernel: rt2800usb 1-7:1.0: firmware: requesting rt2870.bin Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2800usb' ifindex: 6) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/4 Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): now managed Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 1 -> 2 (reason 2) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): bringing up device. Jun 2 20:14:35 localhost kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): preparing device. Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): deactivating device (reason: 2). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): supplicant interface state: starting -> ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 2 -> 3 (reason 42) [root@localhost log]# iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg Mode:Managed Access Point: Not-Associated Tx-Power=8 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on

    Read the article

  • How to specify this 'symbolic link' for the Jungo WinDriver?

    - by user252098
    Just now , I try to install the Jungo WinDriver in the Ubuntu 13.10 . But I am puzzled by the its manual : 4.2.3. Linux WinDriver Installation Instructions 4.2.3.1. Preparing the System for Installation In Linux, kernel modules must be compiled with the same header files that the kernel itself was compiled with. Since WinDriver installs kernel modules, it must compile with the header files of the Linux kernel during the installation process. Therefore, before you install WinDriver for Linux, verify that the Linux source code and the file version.h are installed on your machine: Install the Linux kernel source code: If you have yet to install Linux, install it, including the kernel source code, by following the instructions for your Linux distribution. If Linux is already installed on your machine, check whether the Linux source code was installed. You can do this by looking for 'linux' in the /usr/src directory. If the source code is not installed, either install it, or reinstall Linux with the source code, by following the instructions for your Linux distribution. Install version.h: The file version.h is created when you first compile the Linux kernel source code. Some distributions provide a compiled kernel without the file version.h. Look under /usr/src/linux/include/linux to see whether you have this file. If you do not, follow these steps: Become super user: $ su Change directory to the Linux source directory: cd /usr/src/linux Type: make xconfig Save the configuration by choosing Save and Exit. Type: make dep Exit super user mode: exit To run GUI WinDriver applications (e.g., DriverWizard [5]; Debug Monitor [7.2]) you must also have version 5.0 of the libstdc++ library — libstdc++.so.5. If you do not have this file, install it from the relevant RPM in your Linux distribution (e.g., compat-libstdc++). Before proceeding with the installation, you must also make sure that you have a linux symbolic link. If you do not, create one by typing /usr/src$ ln -s 'target kernel'/linux For example, for the Linux 2.4 kernel type /usr/src$ ln -s linux-2.4/ linux ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ I can't understand how to specify these two parameters in my Ubuntu .

    Read the article

  • GPU not powering on

    - by Lerp
    So I got home from work yesterday and went to turn my computer on as per usual to be greeted by this: The screens remained black, so I rebooted; I go as far as GRUB before my screens went black again. I rebooted again, they didn't turn on. I rebooted again, I got as far as the windows login screen. This time I unplugged it, opened it up and cleaned it but to no luck. The GPU was still being tempermental. I repeated the process of turning off and on several times until one time it work as normal. I happily played games for the rest of the night (5-6 hours?) thinking everything was jolly good now. Well I get home from work today and it is doing the SAME thing. Sometimes everything displays normally for a few seconds to minutes then the screens go black; then sometimes the screens don't come on at all. Summary and additional points Screens sometimes turn on before shortly turning off, sometimes they don't; I cannot seem to determine any pattern between when they do or do not turn off. The build has been working fine for about 8 months now so I know it's not hardware incompatibility. If I plug a monitor into the on board graphics I can use the PC normally (just in low graphics mode) I have two monitors and it's a case of they both turn on or not. So I think I can rule out the monitors being dead. I have tried replacing the GPU I have tried replacing the RAM I have tried flashing the CMOS I have tried cleaning the inside The GPU is a Radeon HD 7870 My questions Is my GPU dead? It's not very old and I would rather have a method of being certain it's the GPU before I fork out some money I can't really afford. I do not have a second PC here to test it in. If my GPU is dead why does it sometimes work and sometimes not? Update Okay, it was working again.. at least I thought it was. I left it running for 10-20minutes with the screens black. Turned it off and straight back on and it worked for all of 10minutes. I was then updating the post in joy thinking I could play some games for the rest of the night when BAM it went black again. So yeah, I don't know :C

    Read the article

  • Unable to locate Windows Server Error log files

    - by Sam007
    I am getting an error in my application on 500 Internal Server Error. The firebug gives me, NetworkError: 500 Internal Server Error - http://webgis.arizona.edu/ArcGIS/rest/services/webGIS/Shock_Models/GPServer/Income_Log/jobs/jc09c501156564f71abc5d98393581267/results/final_shp?dpi=96&transparent=true&format=png8&imageSR=102100&f=image&bbox=%7B%22xmin%22%3A-14519891.438356264%2C%22ymin%22%3A637618.0139790997%2C%22xmax%22%3A-6692739.741956295%2C%22ymax%22%3A6507981.786279075%2C%22spatialReference%22%3A%7B%22wkid%22%3A102100%7D%7D&bboxSR=102100&size=800%2C600 And when I goto that particular link, I get this error, Server Error - Object reference not set to an instance of an object. Any idea how I can correct it? UPDATE I was told to use fiddler and see the error details that is occurring over the network and this is the output that I got, SESSION STATE: Done. Response Entity Size: 849 bytes. == FLAGS ================== BitFlags: [ClientPipeReused, ServerPipeReused] 0x18 X-CLIENTPORT: 2010 X-RESPONSEBODYTRANSFERLENGTH: 849 X-EGRESSPORT: 2023 X-HOSTIP: 128.196.53.161 X-PROCESSINFO: firefox:2248 X-CLIENTIP: 127.0.0.1 X-SERVERSOCKET: REUSE ServerPipe#2 == TIMING INFO ============ ClientConnected: 15:53:51.383 ClientBeginRequest: 15:53:51.494 GotRequestHeaders: 15:53:51.494 ClientDoneRequest: 15:53:51.494 Determine Gateway: 0ms DNS Lookup: 0ms TCP/IP Connect: 0ms HTTPS Handshake: 0ms ServerConnected: 15:52:45.077 FiddlerBeginRequest: 15:53:51.495 ServerGotRequest: 15:53:51.495 ServerBeginResponse: 15:53:51.679 GotResponseHeaders: 15:53:51.679 ServerDoneResponse: 15:53:51.679 ClientBeginResponse: 15:53:51.679 ClientDoneResponse: 15:53:51.679 Overall Elapsed: 00:00:00.1850106 The response was buffered before delivery to the client. == WININET CACHE INFO ============ This URL is not present in the WinINET cache. [Code: 2] * Note: Data above shows WinINET's current cache state, not the state at the time of the request. * Note: Data above shows WinINET's Medium Integrity (non-Protected Mode) cache only. But I am still confused as to what the error is? This is the application. I am not sure if the error is due to the ArcGIS-Server or the Windows Server 2008. I am new on working with the Windows Server and wanted to know where can I look for the error lof files? This is the link which gives the details and the log info of the job executed. This is the output.

    Read the article

  • Getting an boot error when starting computer

    - by Rob Avery IV
    I was in the middle of watching a movie on Netflix, then suddenly everything started crashing. First, explorer.exe closed down, then Google chrome. I had multiple things running in the background (Steam, Raptr, etc.). Individuality, each of those apps closed down also. When they did, a small dialog box popped up for each of them, one at a time, saying that it was missing a file, it couldn't run anymore, or something similar to that. It also had some jumbled up "code" with numbers and letters that I couldn't read. Ever since then, everytime I turn my computer on, it will run for a few seconds and give this error "Reboot and select proper boot device or insert boot media in selected boot device and press a key_". No matter how many times I try to reboot it, it always gives me the same error. A day later after this happened I was able to start the computer, but before it booted, it told me that I didn't shut down the computer properly and asked how I wanted to run the OS (Run Windows in Safety Mode, Run Windows Normally, etc.). Once I logged, everything went SUPER slow and everything crashed almost instantly. The only thing I opened was Microsoft Security Essentials and only got in about two clicks before it was "Not Responding". Then, after that the whole computer froze and I had to restart it. Now, it's back to saying what it originally said, "Reboot and select proper boot device or insert boot media in selected boot device and press a key_". I built this PC back in February 2012. Here are the specs: OS: Windows 7 Ultimate CPU: AMD 8-core GPU: Nvidia GTX Force 560 Ti RAM: 16GB Hard Drive: Hitachi Deskstar 750GB I'm usually very good taking care of my PC. I don't download anything that's not from a trusted site or source. I don't open up any spam email or such or go to any harmful websites like porn or stream movies. I am very clean with the things I do with my PC and don't do many DIFFERENT things with it. I use it pretty often especially for video games and doing homework in Eclipse. Also, good to note that I don't have any Norton or antisoftware installed. I have Microsoft Security Essentials installed but never did a scan. Thanks!

    Read the article

  • OpenVPN multiple servers on the same subnet, high availability

    - by andre
    Hey everyone. Let me start by saying that my Linux experience isn't super awesome but I can usually find my way around things easily. Over at work we have an OpenVPN setup that's been due for some improvement for a while now. The main server (tap mode) runs in our office, behind a rather slow DSL connection. The main problem is that, since I'm usually out of the office, every time I want to access something on the virtual network I have to go through that server to get anywhere else. We have two servers up on 100 Mbit connections that we use for development and production purposes, about 3 more servers in the office (one of them behind a different T1 line for VOIP) and about two dozen clients who use the network on a daily basis from various locations. We've had situations where network routing (outside of our control) would not allow people to reach our main OpenVPN server whilst the other locations were connectable. Also any time someone outside the office wants to fetch something from any of the servers (say, a 500 MB code repository), a whopping 20 KB/s download speed is just unacceptable these days (did I mention slow DSL? ok). We had to implement traffic shaping on this server since maxing out this connection was fairly trivial. I had the thought of running two (or more) OpenVPN servers in the network. These would have to have the same subnet though, as our application relies on virtual network's IP addresses for some of its core functionality. The clients would also preferably retain the same IP addresses but that's not vital. For simplicity, lets call the current server office and the second server I'm setting up, cloud. Call the server on the T1 phone. This proved to be rather complex because as soon as I connect to cloud, I cannot see office. Any routes to a server that would go through office also do not work while I'm connected to cloud (no ping, nothing) and vice-versa. There's no rules for iptables that would be blocking the traffic either. Recently I came across this article on linuxjournal but the solution they provide seems to only cover the use of two servers and somewhat outdated (can't even find much documentation, their wiki is offline). They also state that adding more servers would be a complex task. Ideally I would like to keep the existing server office running the virtual network and also run the OpenVPN daemon on the cloud and phone servers (100 Mbit and very reliable connection, respectively) so that we're on safe ground in case of a hardware failure, DSL failure, etc. So, in essence, I'm looking for a highly available OpenVPN solution (fix, patch, hack, tweak, whatever you want to call it) that will accept connections on multiple hosts (2 or more) whilst keeping the same IP address subnet regardless of the server to which you connect to. Thanks for reading and sorry for the long post, I hope it gets the point across :P

    Read the article

  • Vista stuck at "Shutting down..." screen. Any way to get verbose logging?

    - by CapBBeard
    Hi all, My home machine has been running fine for about 3 years, no problems at all. Within the last couple of weeks it's had real trouble trying to shut down. It'll get so far and then just sit there at the "Shutting down..." screen for hours. I've left it overnight, I've tried in safe mode, all to no avail. These days, I just wait for the disk activity to finish up and then hold the power button to turn it off. Feels dirty as, especially because there's a RAID involved! The hardware itself is in pretty good shape and of decent spec; Core 2 Quad, 4GB RAM, 1TB RAID 1+0, so it's not quite like a 7 year old PC coming to end of life! In the last month, hardware hasn't changed except for a new monitor. Admittedly I haven't tried unplugging the monitor but I've never heard of that preventing a shutdown. I might give it a whirl later I guess, as a last resort. I've uninstalled old apps, done updates, checked the event log, looked in device manager, uninstalled all non-present devices, disabled various non-critical devices (imaging, audio etc), unplugged peripherals, stopped non-essential services, unplugged the network, disabled the network adapter entirely, ran chkdsk, verified my RAID, the list goes on. But not a single lead. I'm pretty stumped. It could be hardware, but I have no other evidence to suggest so; when the PC is running, it runs fine. Temperatures are good, gaming is smooth as always, disk performance is fine. Event log even makes it look like the shutdown was completed (gets to the point where the event log service stops). In fact, the PC doesn't appear to realise that I cut the power to it. So my question is, does anyone know if there is a way I can get some verbose output (or a log) from shutdown to give me some idea of what is causing the issue? I'm guessing it's stuck unloading some app/driver but it would be good to get some specifics! Unless anyone has any other ideas? I suspect a reinstall would resolve the issue, however I'm looking to get a new PC built in the next month or so, and the reinstall is going to be quite a big job so I'd rather just wait until then if it comes to that. Would still be nice to get this sorted in the mean time though. Cheers!

    Read the article

  • How to configure ASP.NET MVC 3 on IIS 6 (Windows 2003 R2)

    - by Nedcode
    I am getting 403 Directory Listing Denied for the root and 404 for an action that I know should exist. Background: I have build and deployed an ASP.NET MVC 2 applcation a long time ago. Later I upgraded it to MVC 3 and it is still working with not configuration changes. Setting it up on a windows 2003 R2 (Standard) initialy was a pain, but after a couple of days(yes, days) struggling it started working. Now I have to do the same with the same application on a different server (2003 R2 Standard again) on a different network. .Net 4 is installed and allowed ASP.NET MVC 3 is also installed By default IIS is set to use .net 4 I verify aspnet_isapi.dll used in application extension are from version 4.0.30319 .NET asemblies folder. I also added the wildcard mapping to aspnet_isapi.dll and unchecked verify file exists. Under Directory Security in Authentication Methods I have disabled anonymos access and enabled Integrated Windows authentication(same as the one on the server that it works) I have copied the same web.config with the <authentication mode="Windows" /> <authorization> <deny users="?" /> </authorization> I have set Read & Execute, List Folder Contents, and Read for the Networkservice account(under which the app pool is working). Also I have set the same for Network account, IIS_WPG, ASPNET and IUSR_MAchineName. I do not have an EnableExte??nsionlessUrls but even if I create it and set it to true or false it does not help. I also tried http://haacked.com/archive/2010/12/22/asp-net-mvc-3-extensionless-urls-on-iis-6.aspx and it did not help. But I kept getting 403 Directory Listing Denied for the root and 404 for an action that I know should exist. Web Platform installer was then used to re-install and possibly update .net, asp.net etc. I then noticed IIS was reset to default. So I added the wildcard mapping again. No, luck still 403. I exported configuration files from the working server setup and created new default app pool and new default website using those configurations. Still I get 403 Directory Listing Denied for the / and 404 for any action I try.

    Read the article

  • how to setup kismet.conf on Ubuntu

    - by Registered User
    I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

    Read the article

  • nginx + Jetty - thousands of connections stuck in LAST_ACK

    - by virulence
    I have a FreeBSD machine with jails -- two in particular, one that runs nginx and another that runs a Java program that accepts requests via Jetty (embedded mode) Jetty receives upwards of 500 requests/sec constantly and there has been an issue lately where I will constantly have over 60,000 connections in the LAST_ACK state between nginx and jetty. Distribution of all connections (includes some other services, particularly php-fpm) root@host:/root # netstat -an > conns.txt root@host:/root # cat conns.txt | awk '{print $6}' | sort | uniq -c | sort -n 18 LISTEN 112 CLOSING 485 ESTABLISHED 650 FIN_WAIT_2 1425 FIN_WAIT_1 3301 TIME_WAIT 64215 LAST_ACK Distribution of nginx - jetty connections root@host:/root # cat conns.txt | grep '10.10.1.57' | awk '{print $6}' | sort | uniq -c | sort -n 1 3 CLOSE_WAIT 3 LISTEN 18 FIN_WAIT_2 125 ESTABLISHED 64193 LAST_ACK I'd prefer every request to fully close the connection. Clients requests are about 10 minutes apart from each other so connections must be closed. Some of the connections, tcp4 0 0 10.10.1.50.46809 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46805 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46797 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46794 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46790 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46789 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46771 10.10.1.57.9050 LAST_ACK etc.. On Jetty's end I've set maxIdleTime to 2000 -- before this all connections were in ESTABLISHED but they are now LAST_ACK On Jetty's end I've set Connection: close (i.e response.setHeader(HttpHeaders.CONNECTION, HttpHeaderValues.CLOSE);) Jetty never reports a lot of open connections -- always very few. PF/IPFW is not currently being used nginx - reset_timedout_connection is on I cannot figure out how to get nginx or jetty to forcibly close the connection, is this simply something that needs to be fixed in Jetty so that it fully closes the socket after the request finishes? Thanks a lot in advance EDIT: forgot my nginx config for the proxy setup- proxy_pass http://10.10.1.57:9050; proxy_set_header HTTP_X_GEOIP $http_x_geoip; proxy_set_header GEOIP_COUNTRY_CODE $geoip_country_code; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_set_header Connection ""; proxy_http_version 1.1; EDIT2: Forcing Jetty to close the connection via request.getConnection().getEndPoint().close() does nothing -- it's obvious the connection IS being closed (as it's in LAST_ACK) but why isn't it getting past this? Is Nginx keeping the connection open to the backend for some reason?

    Read the article

  • Computer freezes +/- 30 seconds, suspicion on SSD

    - by Robert vE
    My computer freezes for about 30 seconds, this happens occasionally. When it happens I can still move the mouse, sometimes even alternate between tabs in google chrome. If I try to open windows explorer nothing happens. Also chrome rapports "waiting for cache". It also happens in starcraft II, during which the sounds loops. I have made a Trace as this topic describes: How do I troubleshoot a Windows 7 freeze or slowness? Trace: https://docs.google.com/open?id=0B_VkKdh535p6NklhSDdBLURUMnc I have looked at it, but I couldn't figure it out. My system specs are: AMD Athlon X4 651 Asus Ati HD6670 ADATA SSD sp900 Asus f1a55 mainboard 4 GB crucial 1333 ram 500 watt atx ps I'm running Windows 7, fully updated. Any help is much appreciated. Update: I tried something before your reply that may have helped the problem. I don't know for sure if it has, it's too soon to tell. A bit of history first. I had problems installing win7 on my ssd from the start. In IDE mode it worked, but I had the same problems as above. AHCI was a total fail, with it on before install as well as turning it on after install (including tweaking register). I didn't bother installing the AMD chipset/AHCI as it was reported to have no TRIM function and thus make problems worse. Eventually I did install the AMD SMbus driver as the stability issues were driving me crazy. It worked, no more issues, until I installed some extra drivers and software. Audio/LAN/ASUS suite, I don’t see the relation, but somehow it screwed up my system again. As a last effort I posted here on this site. After which the thought occurred to me turn on AHCI again as by now I had all necessary drivers installed anyway. (plus all windows updates downloaded/installed in the meantime) I did and stability didn’t seem great the first few reboots, but eventually everything seemed to work great. I tried to play starcraft II – an almost guaranteed freeze before – and I had no problems. I’m basically crossing my fingers and hope the problem is gone for good. I still think it has something to do with my SSD. In my research into the problem I noticed a lot of these issues with sandforce 2281 firmware, the exact same firmware I have. People reported the same problem that I had, freezes. Additionally they reported that during a freeze the hdd light stayed on, I noticed after I read this that this happened with my computer as well. None of this is conclusive evidence that my SSD is really to fault, but it is suspicious. And why turning on AHCI would fix it I don’t know. Thank you Tom for taking a look, if the problem returns I will certainly do what you advised.

    Read the article

  • Linux software Raid 10 no superblock

    - by Shoshomiga
    I have a software raid 10 with 6 x 2tb hard drives (raid 1 for /boot), ubuntu 10.04 is the os. I had a raid controller failure that put 2 drives out of sync, crashed the system and initially the os didnt boot up and went into initramfs instead, saying that drives were busy but I eventually managed to bring the raid up by stopping and assembling the drives. The os booted up and said that there were filesystem errors, I chose to ignore because it would remount the fs in read-only mode if there was a problem. Everything seemed to be working fine and the 2 drives started to rebuild, I was sure that it was a sata controller failure because I had dma errors in my log files. The os crashed soon after that with ext errors. Now its not bringing up the raid, it says that there is no superblock on /dev/sda2. I tried to reassemble manually with all the device names but it still would not bring up the raid 10 complaining about the missing superblock on sda2, and sda1 was also dropped from the raid 1. When I did examine on the raid10 it says that 1 of the initially failed drives is a spare, the other is spare rebuilding and sda2 is removed. It seems that sda decided to fail right when the system was vulnerable to it because when I boot up a live cd it spews out sda unrecoverable read failures. I have been trying to fix this all week but I'm not sure where to go with this now, I ordered more hard drives because I didn't have a complete backup, but its too late for that now and the only thing I could do is mirror all the hard drives onto the new ones (I'm not sure whether sda was mirrored without errors). On the internet I read that you can recover from this by recreating the array with the same options as when it was made, however because sda is failing I cant use it and I don't want to risk using its mirror instead, so I'm waiting to get another hard drive. I'm also not sure whether to include the out of sync drives or if I can actually use those instead to recover the array. Sorry if this is a mess to read but I've been trying to fix this all day and its late at night now, any thoughts on this would be greatly appreciated. I also did a memtest and changed the motherboard in addition to everything else. EDIT: This is my partition layout Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0009c34a Device Boot Start End Blocks Id System /dev/sdb1 * 2048 511999 254976 83 Linux /dev/sdb2 512000 3904980991 1952234496 83 Linux /dev/sdb3 3904980992 3907028991 1024000 82 Linux swap / Solaris

    Read the article

  • NFS4 / ZFS: revert ACL to clean/inherited state

    - by Keiichi
    My problem is identical to this Windows question, but pertains NFS4 (Linux) and the underlying ZFS (OpenIndiana) we are using. We have this ZFS shared via NFS4 and CIFS for Linux and Windows users respectively. It would be nice for both user groups to benefit from ACLs, but the one missing puzzle piece goes thusly: Each user has a home, where he sets a top-level, inherited ACL. He can later on refine permissions for the contained files/folders iteratively. Over time, sometimes permissions need to be generalized again to avoid increasing pollution of ACL entries. You can tweak the ACL of every single file if need be to obtain the wanted permissions, but that defeats the purpose of inherited ACLs. So, how can an ACL be completely cleared like in the question linked above? I have found nothing about what a blank, inherited ACL should look like. This usecase simply does not seem to exist. In fact, the solaris chmod manpage clearly states A- Removes all ACEs for current ACL on file and replaces current ACL with new ACL that represents only the current mode of the file. I.e. we get three new ACL entries filled with stuff representing the permission bits, which is rather useless for cleaning up. If I try to manually remove every ACE, on the last one I get chmod A0- <file> chmod: ERROR: Can't remove all ACL entries from a file Which by the way makes me think: and why not? In fact, I really want the whole file-specific ACL gone. The same holds for linux, which enumerates ACEs starting with 1(!), and verbalizes its woes less diligently nfs4_setacl -x 1 <file> Failed setxattr operation: Unknown error 524 So, what is the idea behind ACLs under Solaris/NFS? Can they never be cleaned up? Why does the recursion option for the ACL setting commands pollute all children instead of setting a single ACL and making the children inherit? Is this really the intention of the designers? I can clean up the ACLs using a windows client perfectly well, but am I supposed to tell the linux users they have to switch OS just to consolidate permissions?

    Read the article

  • Software Raid 10 corrupted superblock after dual disk failure, how do I recover it?

    - by Shoshomiga
    I have a software raid 10 with 6 x 2tb hard drives (raid 1 for /boot), ubuntu 10.04 is the os. I had a raid controller failure that put 2 drives out of sync, crashed the system and initially the os didnt boot up and went into initramfs instead, saying that drives were busy but I eventually managed to bring the raid up by stopping and assembling the drives. The os booted up and said that there were filesystem errors, I chose to ignore because it would remount the fs in read-only mode if there was a problem. Everything seemed to be working fine and the 2 drives started to rebuild, I was sure that it was a sata controller failure because I had dma errors in my log files. The os crashed soon after that with ext errors. Now its not bringing up the raid, it says that there is no superblock on /dev/sda2, even if I assemble manually with all the device names. I also did a memtest and changed the motherboard in addition to everything else. EDIT: This is my partition layout Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0009c34a Device Boot Start End Blocks Id System /dev/sdb1 * 2048 511999 254976 83 Linux /dev/sdb2 512000 3904980991 1952234496 83 Linux /dev/sdb3 3904980992 3907028991 1024000 82 Linux swap / Solaris All 6 disks have the same layout, partition #1 is for raid 1 /boot, partition #2 is for raid 10 far plan, partition #3 is swap, but sda did not have swap enabled EDIT2: This is the output of mdadm --detail /dev/md1 Layout : near=1, far=2 Chunk Size : 64k UUID : a0feff55:2018f8ff:e368bf24:bd0fce41 Events : 0.3112126 Number Major Minor RaidDevice State 0 8 34 0 spare rebuilding /dev/sdc2 1 0 0 1 removed 2 8 18 2 active sync /dev/sdb2 3 8 50 3 active sync /dev/sdd2 4 0 0 4 removed 5 8 82 5 active sync /dev/sdf2 6 8 66 - spare /dev/sde2 EDIT3: I ran ddrescue and it has copied everything from sda except a single 4096 byte sector that I suspect is the raid superblock EDIT4: Here is some more info too long to fit here lshw: http://pastebin.com/2eKrh7nF mdadm --detail /dev/sd[abcdef]1 (raid1): http://pastebin.com/cgMQWerS mdadm --detail /dev/sd[abcdef]2 (raid10): http://pastebin.com/V5dtcGPF dumpe2fs of /dev/sda2 (from the ddrescue cloned drive): http://pastebin.com/sp0GYcJG I tried to recreate md1 based on this info with the command mdadm --create /dev/md1 -v --assume-clean --level=10 --raid-devices=6 --chunk=64K --layout=f2 /dev/sda2 missing /dev/sdc2 /dev/sdd2 missing /dev/sdf2 But I can't mount it, I also tried to recreate it based on my initial mdadm --detail /dev/md1 but it still doesn't mount It also warns me that /dev/sda2 is an ext2fs file system but I guess its because of ddrescue

    Read the article

< Previous Page | 451 452 453 454 455 456 457 458 459 460 461 462  | Next Page >