Search Results

Search found 19279 results on 772 pages for 'everything'.

Page 499/772 | < Previous Page | 495 496 497 498 499 500 501 502 503 504 505 506  | Next Page >

• "Windows detected a hard drive" issue in Windows 7 x64

  - by Jasiu

  I upgraded to the OCZ-Agility3 120GB from a 60 OCZ Vertex2 SSD. I cloned the drive from the Vertex to the new Agility. Everything seemed to have gone well and have not had any problems. Recently in the passed month I have gotten this error: I downloaded teh OCZToolboxMP and ran the SMART utility and don't see anything wrong: SMART READ DATA ModelNumber : OCZ-AGILITY3 Serial Number : OCZ-Y1945X77438P4NU6 WWN : 5-e8-3a-97 ebea5ba76 Revision: 10 Attributes List 1: SSD Raw Read Error Rate Normalized Rate: 70 total ECC and RAISE errors 5: SSD Retired Block Count Reserve blocks remaining: 100% 9: SSD Power-On Hours Total hours power on: 968 12: SSD Power Cycle Count Count of power on/off cycles: 28 171: SSD Program Fail Count Total number of Flash program operation failures: 0 172: SSD Erase Fail Count Total number of Flash erase operation failures: 0 174: SSD Unexpected power loss count Total number of unexpected power loss: 11 177: SSD Wear Range Delta Delta between most-worn and least-worn Flash blocks: 0 181: SSD Program Fail Count Total number of Flash program operation failures: 0 182: SSD Erase Fail Count Total number of Flash erase operation failures: 0 187: SSD Reported Uncorrectable Errors Uncorrectable RAISE errors reported to the host for all data access: 4145 194: SSD Temperature Monitoring Current: 30 High: 30 Low: 30 195: SSD ECC On-the-fly Count Normalized Rate: 120 196: SSD Reallocation Event Count Total number of reallocated Flash blocks: 100 201: SSD Uncorrectable Soft Read Error Rate Normalized Rate: 120 204: SSD Soft ECC Correction Rate (RAISE) Normalized Rate: 120 230: SSD Life Curve Status Current state of drive operation based upon the Life Curve: 100 231: SSD Life Left Approximate SDD life Remaining: 100% 241: SSD Lifetime writes from host lifetime writes 893 GB 242: SSD Lifetime reads from host lifetime reads 968 GB Does anyone have any ideas of what might be wrong and or how I can go about fixing this? Please let me know if there is other information I can provide. Thanks for your help Windows 7 x64 SP1 AMD Phenom II X4 940 8GB RAM

  Read the article

• Iverter, inverter cable, or a display cable?

  - by krebshack

  I was recently hired at a small repair shop. I work indoors while my boss does on site calls for small businesses. I have to troubleshoot and fix laptop screens a few times a week and this is why I'm posting this question. I'm having trouble figuring out how to stream line the troubleshooting process. For example, how do I determine whether the inverter is broken while also determining that the inverter cable is not. How can I quickly decide that the inverter cable is broken while knowing that the inverter is most likely not broke. Or how do I know that it's just the display cable? It seems like this is a good way to approach things: "It could be the inverter, backlight, or the LCD panel itself. Backlight failure is usually hinted at by a pink hue to everything. Inverter failure usually results in the dimming of images on the screen to the point where the backlight is not even on (the inverter provides power to the backlight)" Source. While remembering that things "like flickering, screen freeze in dark image and [a] corner starts to get brighter" point to a "failure in the LCD panel itself, though it could just as easily be a loose data cable connected to the back of the LCD." Source. In short, I'm soliciting advice that anyone might have on how to quickly make the best decision about what's causing problems with laptops display. Thank you.

  Read the article

• Drupal install and permissions

  - by Richard

  So I'm really stuck on this issue. An install process is complaining about write permission on settings.php and sites/default/files/. However, I've moved these files temporarily to write/read (chmod 777) and changed the owner/group to "apache" as shown below. -bash-4.1$ ls -hal total 28K drwxrwxrwx. 3 richard richard 4.0K Aug 23 15:03 . drwxr-xr-x. 4 richard richard 4.0K Aug 18 14:20 .. -rwxrwxrwx. 1 apache apache 9.3K Mar 23 16:34 default.settings.php drwxrwxrwx. 2 apache apache 4.0K Aug 23 15:03 files -rwxrwxrwx. 1 apache apache 0 Aug 23 15:03 settings.php However, the install is still complaining about write permissions. I followed steps one and two of the INSTALL.txt but no luck. Update: To further explore the situation, I created sites/default/richard.php with the following code: <?php error_reporting(E_ALL); ini_set('display_errors', '1'); mkdir('files'); print("<hr> User is "); passthru("whoami"); passthru("pwd"); ?> Run from the command line (under user "richard"), no problem. The folder is created everything is a go. Run from the web, I get the following: Warning: mkdir(): Permission denied in /var/www/html/sites/default/richard.php on line 9 User is apache /var/www/html/sites/default Update 2: Safe mode appears to be off... -bash-4.1$ cat /etc/php.ini | grep safe | grep mode | grep -v \; safe_mode = Off safe_mode_gid = Off safe_mode_include_dir = safe_mode_exec_dir = safe_mode_allowed_env_vars = PHP_ safe_mode_protected_env_vars = LD_LIBRARY_PATH sql.safe_mode = Off

  Read the article

• mysql weird connection problem

  - by santiago.basulto

  Hi guys! I've a weird problem. I've mysql 5.1 installed on my ubuntu 9.04. I've used it a long time (say 3 month) and everything was going right. Until i faced this really weird problem. When i want to connect to a random database i get this message: ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... Connection id: 1 Current database: test_cake ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (111) ERROR: Can't connect to the server It only happens with some databases, while others are totally usefull and healthy. After that, if i try to restart the server i get this. shell /etc/init.d/mysql restart * Stopping MySQL database server mysqld cat: /var/run/mysqld/mysqld.pid: Permiso denegado [fail] * Starting MySQL database server mysqld cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado cat: /var/run/mysqld/mysqld.pid: Permiso denegado [fail] ("permiso denegado" is "permission denied"). I don't know what to do. I change the /var/run/mysqld/mysqld.pid attributes but still not working. Can anybody help me ?

  Read the article

• OpenAM throwing 302 0 behind haproxy, nginx

  - by Travis

  I'm having some issues with my deployment and was wondering if you can help. My set up is as follows: 2 OpenAM servers are set up behind a load balancer (HAproxy). The load balancer is set up behind two reverse proxies (nginx). The two reverse proxies are ser up behind another load balancer (haproxy). So a request will go through Haproxy nginx Haproxy openam I can access the OpenAM web console through the reverse proxies without a problem. Everything works fine at this level. However when I access openam through the load balancer in front of the reverse proxies Openam throws a 302 error. The funny thing is however I can access the host/openam/UI/Login and login successfully. I even get the cookie and have access to my apps that are set up. However immediately after the login OpenAM throws a 302 redirect. I'm puzzled and cannot figure out what is going wrong. Does anyone have any idea? My config files are below: nginx config : server { listen 443; server_name oamlb1; location / { proxy_pass http://oamlb1.mydomain.com:8080; proxy_set_header X-Real-IP $remote_addr; } location /openam { proxy_pass http://oamlb1.mydomain.com:8080; proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host oamlb1.mydomain.com:8080; } } haproxy config : (This file is for the servers. The file for the reverse proxies is idenical except it points to the reverse proxies) listen http_proxy :8090 mode http balance roundrobin option httpclose option forwardfor server webA oamserver1.mydomain.com:18080 option forwardfor Thanks

  Read the article

• Windows Server 2008R2 - can't change or remove the default gateway

  - by disserman

  We've installed VMWare Server 2.0 on Windows 2008R2. After some time playing with it (actually only removing host-only and nat networks, and binding adapters to the specified vmnets) we've noticed a strange problem: if you change or remove the default gateway on the network card, the server completely loses a network connection you can't ping it from the subnet, it also can't connect to anyone. When the gateway is removed and a server tries to connect to the other machines, I can see some incoming packets using a sniffer, but I believe they are damaged in some kind (I'm not a mega-guru in TCP/IP and can't find a mistake in a binary translation of the packet) because the other side doesn't respond. What we tried: removed vmware server using add/remove programs deleted everything related to the vmware server and all installed network adapters in the windows registry double checked for the vmware bridged protocol driver file, it's physically absent and no any links in the registry. performed a tcp/ip reset with netsh and disabled/enabled all network adapters in the device manager to recreate a registry keys for them. tried another network adapter. and the situation is the same: as soon you remove or change the default gateway, windows stops working. The total absurd of the situation is that the default gateway points to the non-existing IP. But when it's set, you can ping a server from the subnet, when you remove it - you can't. Any help? I'm starting thinking the new build of the VMWare Server is some kind of the malware... :)

  Read the article

• Outlook errors and blank address book?

  - by Chasester

  I have a user with a fresh install of Windows 7 64 bit. Office 2010 was installed also. Everything worked great until we installed Adobe Pro 9 and Wordperfect 12. (for outlook we are not using exchange). Then Outlook popped an error saying could not start Outlook. I then modified it to run in compatibility mode and Outlook starts. Then took compatibility mode off and outlook continues to start without difficulty. However, her address book went blank (contacts are all there). In the properties of the contact folder it is checked (and grayed out) to include this folder in the address book, and the Outlook address book is listed when I look at account properties. I tried creating a new profile to no avail. I tried creating a new profile and creating a new pst file - to no avail. I tried uninstalling office, removing the folders inside roaming and local, reinstalled office; got the same could not start Outlook error - did the compatibility mode bit and got it to start - but the Address book continues to be empty. Has anyone run across this before? I'm thinking that there must be some other preferences type folder other than those in Roaming and Local since her signature remained when I reinstalled Office.

  Read the article

• Windows or Linux for VPN-VPN Bridge

  - by James

  I have the following network layout: Network1 ----VPN1-----Network2----VPN2----Network3 I can administer everything in Network1 only and my goal is to get to a box on Network3. I've been told by the admins of Network2 that it's not possible for them to route traffic from Network1 to Network3. I've finally been authorised to host a box in Network2 and I'm hoping with this I can set something up to resolve the issue. My question is should I set this up as a Windows or a Linux box. My initial thought was to use iptables to reroute requests but with my lack of experience with Windows Server (used for something or other in Network2) I'm not sure if this will work. My head's full of questions like: - can I get an ip without logging in to a windows domain? - if I do get an ip, do Windows Servers manage routing through the VPN? - can I make a linux box authenticate with Windows Server to log on to the domain? - would it just be easier to set up a windows box? - is it possible to configure a windows box to do routing from Network1 to Network3? Has anyone done anything like this before? Had experience managing Windows Server? Authenticated (or not as the case may be) to a Windows domain? I'd really appreciate your advice. It might be worth mentioning that the overall objective is to establish a telnet connection from a box on Network1 to a box on Network3.

  Read the article

• Which httpd.conf and php.ini files does plesk use

  - by Saif Bechan

  If i disable the include_path in /etc/php.ini, i can still see that there is an include path loaded from somewhere. I want to know where this file is. If i use phpinfo(); on my domain i get that there is a include path /usr/share/pear:/usr/share/php, even though in the php.ini i used: ;inlucde_path=".:" In the section for aditional php.ini files this is the list: /etc/php.d/curl.ini, /etc/php.d/dbase.ini, /etc/php.d/dom.ini, /etc/php.d/gd.ini, /etc/php.d/imap.ini, /etc/php.d/json.ini, /etc/php.d/mbstring.ini, /etc/php.d/mysql.ini, /etc/php.d/mysqli.ini, /etc/php.d/pdo.ini, /etc/php.d/pdo_mysql.ini, /etc/php.d/pdo_sqlite.ini, /etc/php.d/wddx.ini, /etc/php.d/xmlreader.ini, /etc/php.d/xmlwriter.ini, /etc/php.d/xsl.ini, /etc/php.d/zip.ini I have checked all these files but i can nowhere find a reference to pear. This said the /etc/httpd/conf/httpd.conf file is questioning to me too. If i check this file i can see the following values are defined. DocumentRoot "/var/www/html" <Directory /> Order Deny,Allow Deny from all Options None AllowOverride None </Directory> <Directory "/var/www/html"> Options None AllowOverride None Order allow,deny Allow from all </Directory> The strange thing is that i don't even use this directory, so where does plesk get his httpd.conf file from. I want to check if everything is ok, because my vhost.conf is not working. I don't know if i should change these values or not, and where i can find the values plesk uses. i hope someone can help me with this.

  Read the article

• Asus WL-520GU conflicting subnet (and/or IP) with 2Wire DSL

  - by Paula

  I have an Asus wireless router: WL-520GU... and an AT&T 2Wire for my DSL connection. When I try to browse anywhere, I just get an odd message from the Asus router (in the common Asus broken-English, bad formatting, and awful spelling): http://postimage.org/image/upxrjflcj I guess it's trying to say: Your Asus Router and your 2Wire have the same subnet mask. (It doesn't say if that's good, or bad... but it sounds like they must be different.) but... But for the "solution" it looks like it's trying to say: Your Asus Router and your 2Wire have the same IP address. My Asus has the defaults: 192.168.1.1 and 255.255.255.0 My 2Wire has: 192.168.1.66 I'm not seeing where the conflict(s) could be. The Asus firmware is v3.0.0.14 . None of these problems occur with the old v3.0.0.8 firmware. Any ideas on how to fix this? (PLEASE don't say to run a totally different DD/Tomato firmware because it's "better". I need to fix THIS 1 problem, not try to convince my company to switch everything to an entirely different set of problems.)

  Read the article

• kvm works only when kvm-intel is unloaded

  - by Sathya

  I am new to kvm. I have this strange issue. But before explaining the issue, here is my set up. I try to install VM on my Host which is a Acer Laptop 5720 Has T7500 Intel processor. The cpu flags indicate that Virtualization is supported. I run Ubuntu 10.04 (lucid) on it. It comes with kvm. Now coming to the issue - I dont get any errors while executing "sudo modprobe kvm-intel". So I presume my processor does indeed support hardware virtualization. I use virt-manager and create a VM on which I install ubuntu from an *.iso file. When I start the VM it says it is running. No signs of any trouble. I can see the domain list in "virsh list". But when I try to connect to the VM thru VNC, all I get to see is a blank screen (no cursor). There is no response to any key press. I changed the video mode etc. Tried all different combinations but none work. But strangely, if I shutdown the vm an virt-manager and then unload the module by doing "sudo modprove -r kvm-intel", everything works fine. ie., I can see the screen via VNC. I am able to install the OS and so on. So what does this mean ? IS hardware virtualization not supported ? How come there is no error anywhere ? dmesg | grep kvm doesnt report anything. Can someone throw light on what excatly is happening ?

  Read the article

• Windows 2008 Server cannot access any network share

  - by Ramesh

  Hello friends I run a Windows 2008 server with SP2. This server acts as a desktop alone. Recently, I switched between two networks (corporate and other) using this system. Ever since, I am unable to access any network share on the original network from where I installed and configured the desktop. The message I get is "Network path was not found". Note that I am able to access the internet and my corporate mail server. I am told this is a Vista and Windows 2008 specific problem and I have done everything I could think of: a) Deleted the second network settings from the desktop b) Installed a patch from MS that supposed took care of this problem (with MS clearly saying they had not tested this enough) c) The SP2 install was after the problem occurred and I went ahead with it in the hope that SP2 may have something that would fix this Some additional details: a) A system admin can log into this system from a remote terminal b) I cannot get into my own system using the hidden share C$ - for instance \mymachine\C$ gives me the same message as above - Network path not found c) I can log into my system remotely using mstsc d) I cannot create shares on this system - as an extension network printers are not detected I have an update for you: The error message is as follows - **Network Error** Windows cannot access \\network_share Check the spelling of the name. Otherwise there might a problem with your network. To try to identify and resolve network problems, click Diagnose. Clicking Diagnose gives Error Code: 0x80070035 The network path was not found. Any help will be appreciated Thanks

  Read the article

• How do I host multiple independent, secured SharePoint sites (WSS 3.0) without using Active Director

  - by Kyle Noland

  I have a SharePoint site set up on one of my networks to service Active Directory users. To be clear, this is a Windows SharePoint Services 3.0 installation running on Windows Server 2003 Standard. It is not an option to upgrade the server or SharePoint version. Management would like to create several new sites, one for each of a handful of clients. These sites will be used like "dropboxes" or FTP sites so that my company can make large files available to outside contacts, and vice versa. Here are my requirements: I do not want to have to create Active Directory accounts for each external contact. If possible, I would like to store the external usernames and passwords in a database that I can write a small GUI for so that management can handle adding their own external contacts. Each client site must be sandboxed from each other and from my main company SharePoint site. I would like to keep everything running on port 80 and be able to access the sites as either clientname.mycompany.com or www.mycompany.com/clientname If anybody has ever done this I would really appreciate hearing about any lessons you learned and suggestions for how to set this up. Kyle

  Read the article

• mdadm superblock hiding/shadowing partition

  - by Kjell Andreassen

  Short version: Is it safe to do mdadm --zero-superblock /dev/sdd on a disk with a partition (dev/sdd1), filesystem and data? Will the partition be mountable and the data still there? Longer version: I used to have a raid6 array but decided to dismantle it. The disks from the array are now used as non-raid disks. The superblocks were cleared: sudo mdadm --zero-superblock /dev/sdd The disks were repartitioned with fdisk and filesystems created with mfks.ext4. All disks where mounted and everything worked fine. Today, a couple of weeks later, one of the disks is failing to be recognized when trying to mount it, or rather the single partition on it. sudo mount /dev/sdd1 /mnt/tmp mount: special device /dev/sdd1 does not exist fdisk claims there to be a partition on it: sudo fdisk -l /dev/sdd Disk /dev/sdd: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xb06f6341 Device Boot Start End Blocks Id System /dev/sdd1 1 243201 1953512001 83 Linux Of course mount is right, the device /dev/sdd1 is not there, I'm guessing udev did not create it because of the mdadm data still on it: sudo mdadm --examine /dev/sdd /dev/sdd: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : b164e513:c0584be1:3cc53326:48691084 Name : pringle:0 (local to host pringle) Creation Time : Sat Jun 16 21:37:14 2012 Raid Level : raid6 Raid Devices : 6 Avail Dev Size : 3907027120 (1863.02 GiB 2000.40 GB) Array Size : 15628107776 (7452.06 GiB 8001.59 GB) Used Dev Size : 3907026944 (1863.02 GiB 2000.40 GB) Data Offset : 2048 sectors Super Offset : 8 sectors State : clean Device UUID : 3ccaeb5b:843531e4:87bf1224:382c16e2 Update Time : Sun Aug 12 22:20:39 2012 Checksum : 4c329db0 - correct Events : 1238535 Layout : left-symmetric Chunk Size : 512K Device Role : Active device 3 Array State : AA.AAA ('A' == active, '.' == missing) My mdadm --zero-superblock apparently didn't work. Can I safely try it again without losing data? If not, are there any suggestion on what do to? Not starting mdadm at all on boot might be a (somewhat unsatisfactory) solution.

  Read the article

• HAProxy + NodeJS gets stuck on TCP Retransmission

  - by sled

  I have a HAProxy + NodeJS + Rails Setup, I use the NodeJS Server for file upload purposes. The problem I'm facing is that if I'm uploading through haproxy to nodejs and a "TCP (Fast) Retransmission" occurs because of a lost packet the TX rate on the client drops to zero for about 5-10 secs and gets flooded with TCP Retransmissions. This does not occur if I upload to NodeJS directly (TCP Retransmission happens too but it doesn't get stuck with dozens of retransmission attempts). My test setup is a simple HTML4 FORM (method POST) with a single file input field. The NodeJS Server only reads the incoming data and does nothing else. I've tested this on multiple machines, networks, browsers, always the same issue. Here's a TCP Traffic Dump from the client while uploading a file: ..... TCP 1506 [TCP segment of a reassembled PDU] >> everything is uploading fine until: TCP 1506 [TCP Fast Retransmission] [TCP segment of a reassembled PDU] TCP 66 [TCP Dup ACK 7392#1] 63265 > http [ACK] Seq=4844161 Ack=1 Win=524280 Len=0 TSval=657047088 TSecr=79373730 TCP 1506 [TCP Retransmission] [TCP segment of a reassembled PDU] >> the last message is repeated about 50 times for >>5-10 secs<< (TX drops to 0 on client, RX drops to 0 on server) TCP 1506 [TCP segment of a reassembled PDU] >> upload continues until the next TCP Fast Retransmission and the same thing happens again The haproxy.conf (haproxy v1.4.18 stable) is the following: global log 127.0.0.1 local1 debug maxconn 4096 # Total Max Connections. This is dependent on ulimit nbproc 2 defaults log global mode http option httplog option tcplog frontend http-in bind *:80 timeout client 6000 acl is_websocket path_beg /node/ use_backend node_backend if is_websocket default_backend app_backend # Rails Server (via nginx+passenger) backend app_backend option httpclose option forwardfor timeout server 30000 timeout connect 4000 server app1 127.0.0.1:3000 # node.js backend node_backend reqrep ^([^\ ]*)\ /node/(.*) \1\ /\2 option httpclose option forwardfor timeout queue 5000 timeout server 6000 timeout connect 5000 server node1 127.0.0.1:3200 weight 1 maxconn 4096 Thanks for reading! :) Simon

  Read the article

• signed applet automatically running as insecure

  - by Terje Dahl

  My application is deployed as a self-signed applet to several thousand users at more than 50 schools across the country (in Norway). The user is presented with the standard Java security warning asking if they will accept the signature. When they do, the applet runs perfectly. However, about half a year ago a group of 7 school, all under a common IT department, stopped getting the security warning. In stead the applet loads and starts running in untrusted mode, without first giving the user an option to accept or reject the signature. The problem is on Windows machines, and only when the machine is connected to the schools network. If they take the same machine home with them, the program functions as it should, with security warnings and everything. I know little about Window systems in general, but I would think it would be some sort of policy-file or something that is loaded when a machine hooks up to/through the schools network. Furthermore, the problem only started occurring in these 7 schools after changes made after a security breach they had a while back. The IT department is stumped. I am stumped. Any thoughts, comments, suggestions?

  Read the article

• Ubuntu NBR karmic boot freezes at fsck from util-linux-ng 2.16

  - by BlueBill

  Hi all, I have a netbook (emachine e250 - equivalent to an acer aspire one) and I have Ubunutu NBR 9.10 installed on it. Every other cold boot freezes at the following error message: "fsck from util-linux-ng 2.16" There is no disk activity, no activity what so ever. I have left the machine sit for over an hour and nothing. It takes a couple of hard resets to be able to boot properly. Once it boots everything works great (wireless, suspend/resume, etc.)! I have spent the last couple of weeks researching the problem and the only thing that seems to work is setting nolapic in the boot string in grub - it boots every time. Unfortunately, nolapic disables the second core and causes problems with suspend resume. At first I thought it was an fsck problem with the first partition on the hard disk as it is a hidden ntfs partition containing the windows xp recover information. So in /etc/fstab I set the partition so that it would be ignored by fsck. This didn't seem to do anything. I have these partitions: /dev/sda1 - an ntfs recovery partition /dev/sda2 - /boot /dev/sda3 - swap /dev/sda5 - / /dev/sda6 - /home I am running kernel version 2.6.31-19-generic and have all the patches (as indicated by update manager). I also have no splash screen so I can see the boot progress. I have only been using NBR since January, I have been using Ubuntu on my desktop since last June (2009-06). What logs should I be looking at? Is there a log for failed boots? Thanks, Troy

  Read the article

• DCOM configuration: accounts with same name but different passwords problem

  - by archimed7592

  Hello, everybody! I'm experiencing troubles with DCOM configuration. Here is the case: I'm using some product which supports client-server interaction through DCOM, but the client won't get any access to the server if the attempt is being done from an account with a name which exists at the server as well, but has different password. Basically, if we try to access the server from the Administrator account which obviously present on the server machine, we will fail if client's Administrator password doesn't match server's one. After actively collaborating with the product's developer in attempts to localize the issue, he come across with resolution "can't be fixed" or, if you prefer to call a pikestaff a pikestaff than it's more likely a "don't know how to fix" resolution :). I believe there is a solution for this problem and I'm asking you, IT professionals, to help me out with this one. I do realize that the problem may be caused by the way the developer interact with DCOM and if so it can't be fixed be means of pure system configuration and the question should be asked at SO, but since I've bumped into the same behavior while working with file/printer sharing - Windows tried to simplify everything and used currently impersonated credentials to access the share, I hope the solution lies at system configuration layer. P.S. I believe that the actual software product I'm talking about is entirely irrelevant however my experience tell me that there always would be somebody who will think that it on the contrary is very relevant. Here it is: SpRecord.

  Read the article

• Phpmyadmin location for nginx

  - by multiformeinggno

  I installed nginx and phpmyadmin. I set up a domain with these parameters to test phpmyadmin: server { listen 80; server_name domain.com; root /usr/share/phpmyadmin; index index.php; fastcgi_index index.php; location ~ \.php$ { include /etc/nginx/fastcgi.conf; fastcgi_param SCRIPT_FILENAME /usr/share/phpmyadmin$fastcgi_script_name; fastcgi_pass unix:/var/run/php5-fpm.sock; } } And everything works properly (if I visit the domain I can login to phpmyadmin). The problem is that it was just for testing phpmyadmin, now I'd like to move this to my 'default' site. But I can't figure out how to have it on /phpmyadmin. Here's the config for the 'default' nginx site (where I'd like to put this /phpmyadmin location): server { server_name blabla; access_log /var/log/nginx/$host.access.log; error_log /var/log/nginx/error.log; root /var/www/default; index index.php index.html; location / { try_files $uri $uri/ index.php; } location ~ \.php$ { include /etc/nginx/fastcgi.conf; fastcgi_pass unix:/var/run/php5-fpm.sock; } ### NginX Status location /nginx_status { stub_status on; access_log off; } ### FPM Status location ~ ^/(status|ping)$ { fastcgi_pass unix:/var/run/php5-fpm.sock; access_log off; } }

  Read the article

• Scheduled tasks fail to start unless I'm logged in to the server

  - by Chuck

  Tasks need to open a CMD window and pass net use commands, then do a DIR command, pipping the output to a file on the server. Log in as either me (Sysadmin) or with one of the system accounts and task will only run if I'm physically logged into the server. Run as batch file is set in security properties for both users (me and service account), security is granted to all directories, etc. It almost acts like a scheduled task, since it is not physically connected to a display can't create a CMD window and pass the WinID so the command can be sent. I'm guessing. Anyone know of a document that explains how the server handles initiation of a window if done via scheduled task and no attached user is associated with the task? If I log onto the box and run the scheduled tasks they run fine, but produce no errors or event log entries and then just show that it ran successfully and sets the next run time. Have tried both with the run if logged in checkbox on and off and makes no difference. Other tasks work fine, except that they are acting on local drives with no display writing or updating taking place, so I'm guessing the system either can't instantiate a window if no display is connected to a logged on user, or it can't establish a point if it is trying to create a virtual screen. You'd think it is just creating a memory map and then mapping it to a device to display, but that doesn't seem to be the case, but I can find no documentation on how the system handles a scheduled task and how to invoke a fake or virtual screen that it could write to so it appears that a user was connected. Thanks This is driving me nuts and I've tried everything I can think of as well as our network boys ideas and nothing seems to work.

  Read the article

• Wildcard DNS, VirtualHosts on apache2, 404 for unused subdomains

  - by niel

  On an Apache2 server linked to by a DNS that includes a wildcard entry, e.g. *.example.com, subdomains that are not defined as ServerNames in any VirtualHosts point to the first defined VirtualHost, in my example this is 000-default. My Question:How would one get unused subdomains (subdomains not used in any virtualhosts) to return a 404 error to the requesting client? This must preferably show in server logs as a 404 as well. I have looked into the following possibilities: Redirecting any invalid subdomain to the home page or some other page.The problem with this method is, when someone links to your site as this.company.sucks.example.com, the client will see your home page or in my case 000-default if I do not redirect. Thanks, to Mike for pointing this out. (regex for "suck", etc definately not an option) Let the default VirtualHost point to a non-existent directory.Apache does not like this one bit, warning with every reload. Beyond the warning, everything seems fine. This seems like a hack. Does this seem like a problem (however small) to anyone? Point the default VirtualHost to a folder where the index.php is forbidden, thus creating a 403 status code.This is confusing and makes things like the following overly complicated: Say, for example, you use a subdomain per user (a big reason to use wildcard DNS, apparently), and users have the ability to view each others profiles at username.example.com. This solution is confusing to the user and completely not what I want to do. My ideal sollution will let the user know there is nothing to view at the url he entered. Preferably with a 404 and an error log entry for the address entered (not some other address). Any help would be greatly appreciated!

  Read the article

• Apache reaching MaxClients and locking the server

  - by Rodrigo Sieiro

  Hi. I currently have an Apache2 server running with mpm-prefork and mod_php on a OpenVZ VPS with 512M real / 1024M burstable RAM (no swap). After running some tests, I found that the maximum process size Apache gets is 23M, so I've set MaxClients to 25 (23M x 25 = 575 MB, ok for me). I decided to run some load tests on my server, and the results left me puzzled. I'm using ab on my desktop machine requesting the main page from a wordpress blog. When I run ab with 24 concurrent connections, everything seems fine. Sure, CPU goes up, free RAM goes down, and the result is about 2-3s response time per request. But if I run ab with 25 concurrent connections (my server limit), Apache just hangs after a couple of seconds. It starts processing the requests, then it stops responding, CPU goes back to 100% idle and ab times out. Apache log says it reached MaxClients. When this happens, Apache keeps itself locked up with 25 running processes (they're all in "W" if I check server status) and only after the TimeOut setting the processes start to die and the server starts responding again (in my case it's set to 45). My question: is that expected behaviour? Why Apache just dies when it reaches MaxClients? If it works with 24 connections, shouldn't it work with 25, just taking maybe more time to respond each request and queueing up the rest? It sounds kinda strange to me that any kid running ab can alone kill a webserver just by setting the concurrent connections to the servers MaxClients.

  Read the article

• Passenger error: No such file or directory - config/environment.rb

  - by JJD

  I installed Redmine on MacOSX Server 10.6.8 according to this installation description. So far everything works fine: When I start webrick the server serves the Redmine pages. The gems and redmine are installed under the user "redmine". After that I aimed configuring apache2 with passenger as described here. As suggested by the description I also installed the passenger-pane which stores its virtual host configuration files in /private/etc/apache2/passenger_pane_vhosts. This is what I came up with after a lot of manual try and error. At least, now I can reach a passenger error page. // redmine.vhost.conf <VirtualHost *:80> ServerName host ServerAlias localhost DocumentRoot "/Users/redmine/Sites/redmine" # RackEnv production # RackBaseURI / RailsEnv production RailsBaseURI / # PassengerUser www-data # PassengerGroup www-data <Directory "/Users/redmine/Sites/redmine"> Order allow,deny Allow from all </Directory> </VirtualHost> However, the passenger module still runs into the following errors. Error message: No such file or directory - config/environment.rb The /var/log/apache2/error_log of the web server stated the following. [warn] NameVirtualHost *:80 has no VirtualHosts [notice] Apache/2.2.21 (Unix) Phusion_Passenger/3.0.12 configured -- resuming normal operations [ pid=21824 thr=2151905620 file=utils.rb:176 time=2012-06-01 18:22:07.126 ]: *** Exception Errno::ENOENT in PhusionPassenger::ClassicRails::ApplicationSpawner (No such file or directory - config/environment.rb) (process 21824, thread #<Thread:0x0000010086f2a8>): I experimented with the user switch functionality of passenger as described in the documentation - as you can tell from my configuration file. Though, I was not successful.

  Read the article

• Setting up ProxyPass for a Virtualmin virtual server

  - by Andy Ibanez

  I am trying to set up my web server so that I can server multiple Ghost.org blogs. I am stuck in one crucial step. To be honest, my knowledge in servers is not so big, so I request your help to do this. Basically, a tutorial I'm reading suggests I set up a VirtualHost in this way: NameVirtualHost *:80 <VirtualHost *:80> ServerName your-url.com ServerAlias www.your-url.com ProxyRequests off ProxyPass / http://127.0.0.1:2368/ ProxyPassReverse / http:/127.0.0.1:2368/ </VirtualHost> So I have gone to the Virtual site on Virtualmin to try to add everything as is. Services Configure Website Edit Directives The problem is, the previous page (Services Configure website) says I can't edit the port: This Apache virtual host belongs to the Virtualmin server linguist.andyibanez.com, so the address, port, base directory and hostname cannot be changed here. And whenever I try to add the ProxyRequests off (the other two can be added fine) directive in Edit Directives manually, I'm simply told that the directive can't be there. So what is the right way to "add" the last three directives in the VirtualHost above to my sub server? Maybe I'm missing a menu item that will help me with this? I request your help as I have looked for a while, Google keeps thinking I want to serve Webmin via Apache when I google "Set up Virtualmin proxypass", and I have no clue what to do.

  Read the article

• How to generate customized sudoers files in puppet depending on the environment they're deployed to?

  - by gozu

  the sysadmins are present in the sudoers files of all environments, but other sudoers are not. Different environments all have slightly different sudoers. Most of the time, 90% of users are the same, and 10% vary so we cannot have only one sudoers file for everything. Right now, we are using puppet with 10 different files with names like sudoers.production1, sudoers.production2, sudoers.production3, sudoers.testing1, sudoers.staging1 and so forth. Puppet then picks the file to deploy based on the server's $domain (ex: dbserver.staging1.acme.com) or $hardwaremodel. It works fine but it's a nightmare to maintain so many files. I'd like to autogenerate sudoers files based on the server's domain and have only one big file with all the sudoers permissions for all users and all environments. Something that looks like: User_Alias ADMINS = abe, bob, carol, dave case $domain { "staging1.acme.com" { #add dev1,dev2,tester1,tester2 to sudoers file } "testing2.acme.com" { #add tester1, tester3, tester4 to sudoers file } What's the best way to go about this? Suggestions for alternatives are welcome. I'd appreciate any tips. Update 1: For security reasons, we'd rather not concatenate a bunch of files from a folder located on a puppet client in case someone puts a file in there (maliciously or not) and either breaks the combined file or inserts something in it. Most importantly, for usability, we'd like to keep the number of sudoers related files (fragment or complete) on puppet server to either 3 (prod/stage/test) or preferably 1 file. this file would (somehow) generate sudoers files on the puppet server and send one customized file to each puppet client. The purpose of this would be only searching for a username in a single file and removing it quicker than doing it on 11 files. When adding a user to a bunch of environments, it won't be as quick, but only one file would need to be opened and looked at, greatly reducing the chances of an omission. our Sudo version is 1.6.9p8 so we can't use /sudoers.d folder, only a sudoers file.

  Read the article

< Previous Page | 495 496 497 498 499 500 501 502 503 504 505 506  | Next Page >