Search Results

Search found 430 results on 18 pages for 'sas'.

Page 5/18 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• CentOS - Add additional hard drive raid arrays on Dell Perc 5/i card

  - by Quanano

  We have a Dell Poweredge 2900 system with Dell Perc 5/i card and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on one raid array on this controller with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l: Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v: [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod: Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log blkid: /dev/sda1: UUID="bc4777d9-ae2c-4c58-96ea-cedb342b8338" TYPE="ext4" /dev/sda2: UUID="j2wRZr-Mlko-QWBR-BndC-V2uN-vdhO-iKCuYu" TYPE="LVM2_member" /dev/mapper/vg_lal2server-lv_root: UUID="9238208a-1daf-4c3c-aa9b-469f0387ebee" TYPE="ext4" /dev/mapper/vg_lal2server-lv_swap: UUID="dbefb39c-5871-4bc9-b767-1ef18f12bd3d" TYPE="swap" /dev/mapper/vg_lal2server-lv_home: UUID="ec698993-08b7-443e-84f0-9f9cb31c5da8" TYPE="ext4" dmesg shows: megaraid_sas: fw state:c0000000 megasas: fwstate:c0000000, dis_OCR=0 scsi2 : LSI SAS based MegaRAID driver scsi 2:0:0:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:1:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:2:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:3:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:4:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5 scsi 2:0:5:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5 scsi 2:0:8:0: Direct-Access FUJITSU MBA3073RC D305 PQ: 0 ANSI: 5 scsi 2:0:9:0: Direct-Access FUJITSU MBA3073RC D305 PQ: 0 ANSI: 5 i.e. the 3 RAID Arrays Seagate Hitatchi and Fujitsu hard drives respectively. FURTHER UPDATE I have installed the megaraid storage manager console and connected to the server. It appears that the two CentOS installation hard drives are OK. The other 6 drives, one raid array of 4 and one raid array of 2 disks. The other drives are listed as (Foreign) Unconfigured Good.

  Read the article

• HP DL380 G5 Predictive Drive Failure on a new drive

  - by CharlieJ

  Consolidated Error Report: Controller: Smart Array P400 in slot 3 Device: Physical Drive 1I:1:1 Message: Predictive failure. We have an HP DL380 G5 server with two 72GB 15k SAS drives configured in RAID1. A couple weeks ago, the server reported a drive failure on Drive 1. We replaced the drive with a brand new HDD -- same spares number. A few days ago, the server started reporting a predictive drive failure on the new drive, in the same bay. Is it likely the new drive is bad... or more likely we have a bay failure problem? This is a production server, so any advice would be appreciated. I have another spare drive, so I can hot swap it if this is a fluke and new drive is just bad. THANKS! CharlieJ

  Read the article

• replace controller, add second controller, or use expander?

  - by longneck

  I have a Proliant DL380 G6 that I am re-purposing as a Hyper-V host for a new, off-site data center that will host our DR services. The server currently has a P410i controller with the 512MB BBWC module. The drives installed are SFF 6G 10K drives. I plan to add the HP 516914-B21 drive cage, which gives me 8 more SFF drives, bringing the total to 16. To get the additional 8 drives connected, I have one of three choices: Install a new controller that can support 16 drives. Install a second controller. Install a SAS expander, such as the HP 468406-B21 recommended by HP's spec sheet for my server. My question is: how do I know if I'm going hit a performance ceiling by putting 16 drives on the P410i or using the expander? And if I am, how do I select an appropriate controller? I'm not sure what specifications I should be looking at.

  Read the article

• Can I get redundancy with a JBOD storage subsystem

  - by Dat Chu

  I have a Promise Technology J610S. This is a JBOD subsystem. Is it possible for me to buy a SAS hardware RAID controller and provide some type of redundancy for these drives? I am unsure whether I will use Linux or Windows yet so an answer with enumeration for both would be highly appreciated. One solution that I thought of was: if my J610s can export each drive as a target, my server will simply see 16 drives. The RAID controller can then perform the RAID5/RAID6 if I want.

  Read the article

• spontaneous hard disk password

  - by sc

  I had an HP proliant server go down recently. All of the sudden the sas controller (e200i) would not see any of the physical disks. New disks were detected just fine. I thought it was odd that all 6 disks would go down at one time so sent them to a data recovery firm to find out what happened. I'm being told that, somehow, all of the disks were spontaneously password protected. These are Hitachi 2.5" drives and I guess this is something of a known issue. The company has worked for a while to try and recover them, with no luck. Has anyone had experience with this? Any recommendations for how to recover the drives or a company that might have the expertise to do so?

  Read the article

• SSD Performance for PHP?

  - by Andrew Fashion

  My programmer just built an application with PHP using Doctrine ORM (will be a high traffic social networking website), and it's very heavy in PHP/Apache and CPU. The queries are wonderfully fast, and MySQL is barely using any CPU, it's just Apache. I was curious to if an SSD would help speed up PHP/Apache, because I know the bottleneck is in PHP reading multiple files, class files, and loading up a bunch of data. So common sense makes me think if PHP is reading multiple PHP files, an SSD would only help as far as read/write? I was thinking of doing a high performance SSD for the PHP application, but for user image uploads, I would just continue using a 15k SAS. Is there any performance issues regarding using an SSD in this kind of situation? And would it prove to help speed up PHP/Apache, and help the CPU problem out?

  Read the article

• RAID 10 over RAID 5 when using SSDs

  - by root

  I am considering implementing an iSCSI shared storage array using SATA SSDs instead of the 15k RPM SAS drives we normally purchase. We normally use RAID 10 because of spindle contention with the random IO produced by virtualized workloads. I was wondering if we could switch to RAID 5 or RAID 6 to have more usuable space now that spindle contention is less of an issue. A question in my mind is how much overhead there is from the controller calculating parity. I am aware that this configuration will not allow TRIM to function. Our current workloads are running on a Dell H800 with a 24 bay external enclosure.

  Read the article

• Categorize data without consolidating?

  - by sqlnoob

  I have a table with about 1000 records and 2000 columns. What I want to do is categorize each row such that all records with equal column values for all columns except 'ID' are given a category ID. My final answer would look like: ID A B C ..... Category ID 1 1 0 3 1 2 2 1 3 2 3 1 0 3 1 4 2 1 3 2 5 4 5 6 3 6 4 5 6 3 where all columns (besides ID) are equal for IDs 1,3 so they get the same category ID and so on. I guess my thought was to just write a SQL query that does a group by on every single column besides 'ID' and assign a number to each group and then join back to my original table. My current input is a text file, and I have SAS, MS Access, and Excel to work with. (I could use proc sql from within SAS). Before I go this route and construct the whole query, I was just wondering if there was a better way to do this? It will take some work just to write the query, and I'm not even sure if it is practical to join on 2000 columns (never tried), so I thought I'd ask for ideas before I got too far down the wrong path. EDIT: I just realized my title doesn't really make sense. What I was originally thinking was "Is there a way I can group by and categorize at the same time without actually consolidating into groups?"

  Read the article

• Merging datasets with 2 different time variables in SAS

  - by John

  Hye Guys, for those regularly browsing this site sorry for already another question (however I did solve my last question myself!) I have another problem with merging datasets, it seems that accounting for time in datasets is a real pain in the ass. I succesfully managed to merge on months in my previous datasets, however it seems I have a final dataset which only has quarter as a time count variable. So where all my normal databases have month 1- xxx as an indicator of time, this database had quarter as an indicator of time. I still want to add the variables of this last database, let's call it TVOL, into my WORK database. Quick summary QUARTER: Quarter 0 = JAN1996-MAR1996 Month: Month 0 = JAN1996 Example: TVOL TVOL _ Ticker ____ Quarter 1500 _ AA ________ -1 52546 _ BB ________ 15 Example: WORK BETA _ Ticker ____ Month 1.52 _ AA ________ 2 1.54__ BB _______ 3 Example: Merged: BETA ______ TVOL __ Ticker ____ Month 1.52 _______ 500 ___ AA _______ 2 I now want to merge this 2 tables using following relationship if the month is in quarter 1, the data of quarter 0 has to be used, so if i have an observation i nWORK with date 2FEB1996 the TVOL of quarter -1 has to be put behind this observation. Something like IF month = quarter i use data quarter i-1. Also, as TVOL is measured quarterly and I have to put in monthly I have to take the average, so (TVOL/3) should be added as a variable. Thanks!

  Read the article

• LSI 9211-8i won't boot in KVM

  - by Paul McMillan

  I'm running ubuntu 11.04 with an LSI 9211-8i in IT mode with the latest firmware (10). I'm using KVM with VT-d enabled to pass the entire PCIe device through to the guest OS. I have the device disabled in the system BIOS. When I boot my virtual machine, the adapter quits during bios initialization with the following error: Unable to load LSI Corporation MPT BIOS MPT BIOS Fault 0Ch encountered at adapter PCI(00h,04h,00h) Press any key to continue... I know the virtualization is correctly enabled. I've blacklisted the kernel modules in the host OS. Has anyone else encountered this error? I'm about out of ideas here. Edit: I contacted LSI tech support about this, and they suggested that I try RedHat and Xen. Apparently they don't test or support anything else.

  Read the article

• How can a single disk in a hardware SATA RAID-10 array bring the entire array to a screeching halt?

  - by Stu Thompson

  Prelude: I'm a code-monkey that's increasingly taken on SysAdmin duties for my small company. My code is our product, and increasingly we provide the same app as SaaS. About 18 months ago I moved our servers from a premium hosting centric vendor to a barebones rack pusher in a tier IV data center. (Literally across the street.) This ment doing much more ourselves--things like networking, storage and monitoring. As part the big move, to replace our leased direct attached storage from the hosting company, I built a 9TB two-node NAS based on SuperMicro chassises, 3ware RAID cards, Ubuntu 10.04, two dozen SATA disks, DRBD and . It's all lovingly documented in three blog posts: Building up & testing a new 9TB SATA RAID10 NFSv4 NAS: Part I, Part II and Part III. We also setup a Cacit monitoring system. Recently we've been adding more and more data points, like SMART values. I could not have done all this without the awesome boffins at ServerFault. It's been a fun and educational experience. My boss is happy (we saved bucket loads of $$$), our customers are happy (storage costs are down), I'm happy (fun, fun, fun). Until yesterday. Outage & Recovery: Some time after lunch we started getting reports of sluggish performance from our application, an on-demand streaming media CMS. About the same time our Cacti monitoring system sent a blizzard of emails. One of the more telling alerts was a graph of iostat await. Performance became so degraded that Pingdom began sending "server down" notifications. The overall load was moderate, there was not traffic spike. After logging onto the application servers, NFS clients of the NAS, I confirmed that just about everything was experiencing highly intermittent and insanely long IO wait times. And once I hopped onto the primary NAS node itself, the same delays were evident when trying to navigate the problem array's file system. Time to fail over, that went well. Within 20 minuts everything was confirmed to be back up and running perfectly. Post-Mortem: After any and all system failures I perform a post-mortem to determine the cause of the failure. First thing I did was ssh back into the box and start reviewing logs. It was offline, completely. Time for a trip to the data center. Hardware reset, backup an and running. In /var/syslog I found this scary looking entry: Nov 15 06:49:44 umbilo smartd[2827]: Device: /dev/twa0 [3ware_disk_00], 6 Currently unreadable (pending) sectors Nov 15 06:49:44 umbilo smartd[2827]: Device: /dev/twa0 [3ware_disk_07], SMART Prefailure Attribute: 1 Raw_Read_Error_Rate changed from 171 to 170 Nov 15 06:49:45 umbilo smartd[2827]: Device: /dev/twa0 [3ware_disk_10], 16 Currently unreadable (pending) sectors Nov 15 06:49:45 umbilo smartd[2827]: Device: /dev/twa0 [3ware_disk_10], 4 Offline uncorrectable sectors Nov 15 06:49:45 umbilo smartd[2827]: Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error Nov 15 06:49:45 umbilo smartd[2827]: # 1 Short offline Completed: read failure 90% 6576 3421766910 Nov 15 06:49:45 umbilo smartd[2827]: # 2 Short offline Completed: read failure 90% 6087 3421766910 Nov 15 06:49:45 umbilo smartd[2827]: # 3 Short offline Completed: read failure 10% 5901 656821791 Nov 15 06:49:45 umbilo smartd[2827]: # 4 Short offline Completed: read failure 90% 5818 651637856 Nov 15 06:49:45 umbilo smartd[2827]: So I went to check the Cacti graphs for the disks in the array. Here we see that, yes, disk 7 is slipping away just like syslog says it is. But we also see that disk 8's SMART Read Erros are fluctuating. There are no messages about disk 8 in syslog. More interesting is that the fluctuating values for disk 8 directly correlate to the high IO wait times! My interpretation is that: Disk 8 is experiencing an odd hardware fault that results in intermittent long operation times. Somehow this fault condition on the disk is locking up the entire array Maybe there is a more accurate or correct description, but the net result has been that the one disk is impacting the performance of the whole array. The Question(s) How can a single disk in a hardware SATA RAID-10 array bring the entire array to a screeching halt? Am I being naïve to think that the RAID card should have dealt with this? How can I prevent a single misbehaving disk from impacting the entire array? Am I missing something?

  Read the article

• Statistics based marketing campaign measurement tools

  - by AFHood

  Currently using SAS as measurement engine and Business Objects as display layer. Looking to develop a new, faster, slicker solution. Has anyone developed or purchased a campaign measurement reporting system? This solution should measure everything from email stats, web stats, customer activity, lift, ROI, etc. Ok.. I'm researching and finding nada... We are working with a team from India and they want to re-write everything from scratch.. Any solutions out there at all?

  Read the article

• Creating transparent gridlines

  - by Rob Penridge

  I'm trying to get the chart's gridlines to be transparent but it doesn't seem to be supported: http://support.sas.com/documentation/cdl/en/grstatug/63302/HTML/default/viewer.htm#n1f71f6e9v037an1jy274v66z4r1.htm I'm doing to try and blend the gridlines with the chart background color (which in my code can change between colors) which would make the gridlines subtle rather than jarring when background colors change. Here is my code: ** ** TAKE THE DEFAULT STYLE BEING USED. MODIFY IT SO THAT ** GRAPH GRIDLINES WILL BE GREEN AND MOSTLY TRANSPARENT *; proc template; define style my_style; parent = styles.default; style GraphGridLines from GraphGridLines / contrastcolor=green transparency=.05; end; run; ** ** LAYOUT TEMPLATE FOR A SIMPLE SERIES CHART *; proc template; define statgraph mychart; begingraph; layout overlay / wallcolor=black xaxisopts=(display=(line) griddisplay=on) yaxisopts=(display=(line)) ; seriesplot x=name y=height / lineattrs=(color=white); endlayout; endgraph; end; run; ** ** PLOT SAMPLE DATA USING CUSTOM STYLE AND CHART LAYOUT WE JUST DEFINED *; ods graphics / width=640 height=640 ; ods html style=my_style; proc sgrender data=sashelp.class template=mychart; run; ods html close; Is there another way to achieve this effect by blending the green color with the background color?

  Read the article

• Proliant server will not accept new hard disks in RAID 1+0?

  - by Leigh

  I have a HP ProLiant DL380 G5, I have two logical drives configured with RAID. I have one logical drive RAID 1+0 with two 72 gb 10k sas 1 port spare no 376597-001. I had one hard disk fail and ordered a replacement. The configuration utility showed error and would not rebuild the RAID. I presumed a hard disk fault and ordered a replacement again. In the mean time I put the original failed disk back in the server and this started rebuilding. Currently shows ok status however in the log I can see hardware errors. The new disk has come and I again have the same problem of not accepting the hard disk. I have updated the P400 controller with the latest firmware 7.24 , but still no luck. The only difference I can see is the original drive has firmware 0103 (same as the RAID drive) and the new one has HPD2. Any advice would be appreciated. Thanks in advance Logs from server ctrl all show config Smart Array P400 in Slot 1 (sn: PAFGK0P9VWO0UQ) array A (SAS, Unused Space: 0 MB) logicaldrive 1 (68.5 GB, RAID 1, Interim Recovery Mode) physicaldrive 2I:1:1 (port 2I:box 1:bay 1, SAS, 73.5 GB, OK) physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 72 GB, Failed array B (SAS, Unused Space: 0 MB) logicaldrive 2 (558.7 GB, RAID 5, OK) physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS, 300 GB, OK) physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK) physicaldrive 2I:1:4 (port 2I:box 1:bay 4, SAS, 300 GB, OK) ctrl all show config detail Smart Array P400 in Slot 1 Bus Interface: PCI Slot: 1 Serial Number: PAFGK0P9VWO0UQ Cache Serial Number: PA82C0J9VWL8I7 RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: E Firmware Version: 7.24 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Status Details: A cache error was detected. Run more information. Cache Ratio: 100% Read / 0% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Battery/Capacitor Count: 0 SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 0 MB Status: Failed Physical Drive Array Type: Data One of the drives on this array have failed or has Logical Drive: 1 Size: 68.5 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 17594 Strip Size: 128 KB Full Stripe Size: 128 KB Status: Interim Recovery Mode Caching: Enabled Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive0 Mount Points: C:\ 68.5 GB Logical Drive Label: A0100539PAFGK0P9VWO0UQ0E93 Mirror Group 0: physicaldrive 2I:1:2 (port 2I:box 1:bay 2, S Mirror Group 1: physicaldrive 2I:1:1 (port 2I:box 1:bay 1, S Drive Type: Data physicaldrive 2I:1:1 Port: 2I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 73.5 GB Rotational Speed: 10000 Firmware Revision: 0103 Serial Number: B379P8C006RK Model: HP DG072A9B7 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:2 Port: 2I Box: 1 Bay: 2 Status: Failed Drive Type: Data Drive Interface Type: SAS Size: 72 GB Rotational Speed: 15000 Firmware Revision: HPD9 Serial Number: D5A1PCA04SL01244 Model: HP EH0072FARUA PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data Logical Drive: 2 Size: 558.7 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Co Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive1 Mount Points: E:\ 558.7 GB Logical Drive Label: AF14FD12PAFGK0P9VWO0UQD007 Drive Type: Data physicaldrive 1I:1:5 Port: 1I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE07QH300009923X1X3 Model: HP DG0300BALVP Current Temperature (C): 32 Maximum Temperature (C): 45 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:3 Port: 2I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE0AHVH00009924P8F3 Model: HP DG0300BALVP Current Temperature (C): 34 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:4 Port: 2I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE08NAK00009924KWD6 Model: HP DG0300BALVP Current Temperature (C): 35 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown

  Read the article

• Has anybody tried to create a really big storage with ZFS and plain SAS controllers? [closed]

  - by Eccehomo

  I'm considering to build one with something like this: http://www.supermicro.com/products/chassis/4U/847/SC847E26-R1400U.cfm (a chasis with two dual port multipath expanders) http://www.supermicro.com/products/accessories/addon/AOC-SAS2LP-MV8.cfm (4 8-port plain SAS controllers, 2 for each backplane) and 36 Seagate 3Tb SAS drives (ST33000650SS) OS -- FreeBSD. And it's very interesting: How good expander sas backplanes and multipath configurations work with freebsd ? How to locate a specific drive in the bay? (literally -- how to blink an indicator on the drive in freebsd) How to detect a fail of a controller? Will it work together at all? I'm asking to share any experience.

  Read the article

• Does the QPI figure matter for large scale data processing using SAS?

  - by xiaodai

  At work we use SAS to manipulte large amounts of data everyday on our workstations. To give an indication of scale the largest merges we had to do was merging 24 files of 2GB in size each together into one big file (if you are familiar with SAS the files are binary compressed too!). If we upgrade our PCs to core i7 then which of Core i7 975 or Core i7 960 is better? The main difference between the two seems to be QPI. So does that affect large scale data processing such as merge datasets in SAS?

  Read the article

• In need of a SaaS solution for semantic thesaurus matching

  - by Roy Peleg

  Hello, I'm currently building a web application. In one of it's key processes the application need to match short phrases to other similar ones available in the DB. The application needs to be able to match the phrase: Looking for a second hand car in good shape To other phrases which basically have the same meaning but use different wording, such as: 2nd hand car in great condition needed or searching for a used car in optimal quality The phrases are length limited (say 250 chars), user generated & unstructured. I'm in need of a service / company / some solution which can help / do these connections for me. Can anyone give any ideas? Thanks, Roy

  Read the article

• Word wrapping issue in text file export

  - by photec

  I just whipped up a program to export a dataset to a text file and am running into a issue with data from an observation being wrapped to the line below in the exported file. Below is a stripped down version of my program and the text seems to be wrapping at column 1025. Does anyone happen to know why this is occurring and how to go about ensuring that record data stays on its own row? Any help would be greatly appreciated. data ; set (firstobs = 1 obs = 75); file '\' lrecl = 32767; put first_var $1 ... last_var 1244; run;

  Read the article

• Hard drives indication with controller MegaRAID SAS 9261-8i on HP Proliant DL320e Gen8. Is it possible?

  - by ame

  Give me advice, please. My situation: There're the server HP ProLiant DL320e Gen8 and MegaRAID SAS 9261-8i RAID Controller. I installed Controller into server and I reconnected Mini-SAS cord from block of hard drives to controller, but I haven't any indication of hard discs on server front panel. There's indication of activity of drives only during boot of server. Controller has 2-pin connector (JT6B3, SAS Activity LED header) but where and how can I connect it? Thanx.

  Read the article

• Can I rebuild degraded RAID1 on a SAS 5 i controller with a larger mirror drive size?

  - by Kenny

  A drive failed on a Dell SAS 5i controller - see controller bios screengrab: http://imagebin.ca/view/SkZbszA.html The primary is a 160GB 10k sata drive. I added a 250GB 7k rpm drive in the hope that the array would rebuild onto this drive. This did not happen. (assuming that the controller would just operate at the speed of the slowest drive) The controller could see the new drive, but it didn't automatically rebuild the raid1 onto this drive. (my assumption is that it did not do this rebuild as the drive sizes are different). There was an option to add the new drive to the existing raid1 array - but when I tried this a message appeared stating that all data on the array would be lost. (I didn't get a screenshot of this message, I will later) Should the SAS 5i allow me to rebuild the array onto a larger drive? Is the option to add the drive to the array the right way to go? Many thanks!

  Read the article

• Can I rebuild degraded RAID1 on a SAS 5 i controller with a larger mirror drive size?

  - by Kenny

  Hi, A drive failed on a Dell SAS 5i controller - see controller bios screengrab: http://imagebin.ca/view/SkZbszA.html The primary is a 160GB 10k sata drive. I added a 250GB 7k rpm drive in the hope that the array would rebuild onto this drive. This did not happen. (assuming that the controller would just operate at the speed of the slowest drive) The controller could see the new drive, but it didn't automatically rebuild the raid1 onto this drive. (my assumption is that it did not do this rebuild as the drive sizes are different). There was an option to add the new drive to the existing raid1 array - but when I tried this a message appeared stating that all data on the array would be lost. (I didn't get a screenshot of this message, I will later) Should the SAS 5i allow me to rebuild the array onto a larger drive? Is the option to add the drive to the array the right way to go? Many thanks!

  Read the article

• Email alerts when hard drive fails on a Dell PowerEdge 2950 (PERC5I, SAS)?

  - by BigJoe714

  I recently purchased a used Dell PowerEdge 2950. I setup the hard drives in RAID-5 configuration. I want to be able to get an email alert if one of the drives fails. I have been trying to determine what the easiest way to setup an email alert would be. The controller card is listed as PERC5I, SAS PowerEdge. From my numerous Google searches, it looks like I need to install Dell OpenManage Essentials. However ,this looks to be a giant application with tons of bells & whistles for managing many servers, when all I really want is something for this one server. Can anyone offer me any insight into what I could do?

  Read the article

• New Write Flash SSDs and more disk trays

  - by Steve Tunstall

  In case you haven't heard, the Write SSDs the ZFSSA have been updated. Much faster now for the same price. Sweet. The new write-flash SSDs have a new part number of 7105026 , so make sure you order the right ones. It's important to note that you MUST be on code level 2011.1.4.0 or higher to use these. They have increased in IOPS from 6,000 to 11,000, and increased throughput from 200MB/s to 350MB/s.    Also, you can now add six SAS HBAs (up from 4) to the 7420, allowing one to have three SAS channels with 12 disk trays each, for a new total of 36 disk trays. With 3TB drives, that's 2.5 Petabytes. Is that enough for you? Make sure you add new cards to the correct slots. I've talked about this before, but here is the handy-dandy matrix again so you don't have to go find it. Remember the rules: You can have 6 of any one kind of card (like six 10GigE cards), but you only really get 8 slots, since you have two SAS cards no matter what. If you want more than 12 disk trays, you need two more SAS cards, so think about expansion later, too. In fact, if you are going to have two different speeds of drives, in other words you want to mix 15K speed and 7,200 speed drives in the same system, I would highly recommend two different SAS channels. So I would want four SAS cards in that system, no matter how many trays you have. 

  Read the article

• Decyphering Seagate drive model numbers?

  - by Stefan Lasiewski

  I'm comparing Seagate's Enterprise and Desktop drives for a variety of old and new servers. These servers come from different generations, so options like size (73GB, 2TB) and interface (SATA vs SAS 3.0Gbps vs SAS 6Gbps vs SCSI Ultra320) are widely variable. I'm trying to compare the sizes, speeds and interfaces, but I'm getting thrown off by different models. Also, their website is not the best. Does anyone know of a documented explanation of the Seagate model numbers? And is there a single spreadsheet which compares the features for all drives (or all 'Enterprise' drives?). Seagate drives have model numbers like this: Model ST3600057SS 6-Gb/s SAS 600 GB None at Cheetah® 15K Hard Drives Model ST373455LW Ultra320 SCSI 73.4 GB 68-Pin LW at Cheetah® 15K Hard Drives Model ST32000644NS SATA 3Gb/s 2 TB None at Constellation™ ES Hard Drives Model ST973452SS 6-Gb/s SAS 73 GB None Savvio® 15K Hard Drives Model ST9200011FS SATA 3Gb/s 200 GB Pulsar™ Solid State Drives I understand the model numbers read something like this: ST - SOMETHING1 - SIZE - SOMETHING2 - INTERFACE Where the fields mean something like this: ST : For 'Seagate'? 'Seagate Technoligies'? SOMETHING1 - This field has number, but I'm not sure what that represents. SIZE - Size in Gigabytes. This is a number like '73' or '300' or '2000' SOMETHING2 - This field also has a number, but I'm not sure what it means. INTERFACE - This field seems to indicate the Interface. 'SS' means SAS, 'FC' means Fibre Channel, but I don't see how to distinguish between 6Gbps SAS and 3Gbps SAS, or different SATA or FC speeds. I don't see a field which indicates the RPM (15K , 10K, 7.2K) etc. Is this part of the model number?

  Read the article

• Can't Remove Logical Drive/Array from HP P400

  - by Myles

  This is my first post here. Thank you in advance for any assistance with this matter. I'm trying to remove a logical drive (logical drive 2) and an array (array "B") from my Smart Array P400. The host is a DL580 G5 running 64-bit Red Hat Enterprise Linux Server release 5.7 (Tikanga). I am unable to remove the array using either hpacucli or cpqacuxe. I believe it is because of "OS Status: LOCKED". The file system that lives on this array has been unmounted. I do not want to reboot the host. Is there some way to "release" this logical drive so I can remove the array? Note that I do not need to preserve the data on logical drive 2. I intend to physically remove the drives from the machine and replace them with larger drives. I'm using the cciss kernel module that ships with Red Hat 5.7. Here is some information pertaining to the host and the P400 configuration: [root@gort ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.7 (Tikanga) [root@gort ~]# uname -a Linux gort 2.6.18-274.el5 #1 SMP Fri Jul 8 17:36:59 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux [root@gort ~]# rpm -qa | egrep '^(hp|cpq)' cpqacuxe-9.30-15.0 hp-health-9.25-1551.7.rhel5 hpsmh-7.1.2-3 hpdiags-9.3.0-466 hponcfg-3.1.0-0 hp-snmp-agents-9.25-2384.8.rhel5 hpacucli-9.30-15.0 [root@gort ~]# hpacucli HP Array Configuration Utility CLI 9.30.15.0 Detecting Controllers...Done. Type "help" for a list of supported commands. Type "exit" to close the console. => ctrl all show config detail Smart Array P400 in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Cache Serial Number: PA82C0J9SVW34U RAID 6 (ADG) Status: Enabled Controller Status: OK Hardware Revision: D Firmware Version: 7.22 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Logical Drive: 1 Size: 136.7 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 35132 Strip Size: 128 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Unique Identifier: 600508B100184A395356573334550002 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 101 MB, /tmp 7.8 GB, /usr 3.9 GB, /usr/local 2.0 GB, /var 3.9 GB, / 2.0 GB, /local 113.2 GB OS Status: LOCKED Logical Drive Label: A0027AA78DEE Mirror Group 0: physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) Drive Type: Data Array: A Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM57RF40000983878FX Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 35 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM55VQC000098388524 Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 36 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Logical Drive: 2 Size: 546.8 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 256 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Completed Unique Identifier: 600508B100184A395356573334550003 Disk Name: /dev/cciss/c0d1 Mount Points: None OS Status: LOCKED Logical Drive Label: A5C9C6F81504 Drive Type: Data Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2H5PE00009802NK19 Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 37 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 1I:1:4 Port: 1I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM28YY400009750MKPJ Model: HP DG146ABAB4 Current Temperature (C): 31 Maximum Temperature (C): 36 PHY Count: 1 PHY Transfer Rate: 3.0Gbps physicaldrive 2I:1:5 Port: 2I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FGYV00009802N3GN Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 38 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 2I:1:6 Port: 2I Box: 1 Bay: 6 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM8AFAK00009920MMV1 Model: HP DG146BB976 Current Temperature (C): 31 Maximum Temperature (C): 41 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:7 Port: 2I Box: 1 Bay: 7 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FJQD00009801MSHQ Model: HP DG146ABAB4 Current Temperature (C): 29 Maximum Temperature (C): 39 PHY Count: 1 PHY Transfer Rate: Unknown

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >