Search Results

Search found 15605 results on 625 pages for 'cached exchange mode'.

Page 505/625 | < Previous Page | 501 502 503 504 505 506 507 508 509 510 511 512  | Next Page >

  • Getting 502 instead of 503 when all backend servers are down running HAProxy behind Apache

    - by scarba05
    I'm testing running HAProxy as a dedicated load balancer behind Apache 2.2, replacing our current configuration where we use Apache's load balancer. In our current, Apache only, set-up if all the backend (origin) servers are down Apache will serve a 503 service unavailable message. With HAProxy I get a 502 bad gateway response. I'm using a simple reverse proxy rewrite rule in Apache RewriteRule ^/(.*) http://127.0.0.1:8000/$1 [last,proxy] In HAProxy I have the following (running in default tcp mode) defaults log global option tcp-smart-accept timeout connect 7s timeout client 60s timeout queue 120s timeout server 60s listen my_server 127.0.0.1:8000 balance leastconn server backend1 127.0.0.1:8001 check observe layer4 maxconn 2 server backend1 127.0.0.1:8001 check observe layer4 maxconn 2 Testing connecting directly to the load balancer when the backend servers are down: [root@dev ~]# wget http://127.0.0.1:8000/ test.html --2012-05-28 11:45:28-- http://127.0.0.1:8000/ Connecting to 127.0.0.1:8000... connected. HTTP request sent, awaiting response... No data received. So presumably this is down to the fact that HAProxy accepts the connection and then closes it.

    Read the article

  • Authenticated User Impersonation in Classic ASP under IIS7

    - by user52663
    I've recently moved one of our servers from Server 2003 and IIS6 to Server 2008 R2 and IIS7 (technically IIS7.5 I suppose). In doing so I am transitioning a small account management tool written in classic ASP and have run into a problem with user impersonation. Extensive searching hasn't been much help so far. Under IIS6, the site was configured to impersonate the logged-in user. Thus, if a domain admin logged in, he was able to run commands to create user directories, adjust permissions, etc. Using Procmon you can see the processes executing as that user. This worked fine. However, with the same code under IIS7, I am unable to get this behavior. I have enabled Basic Authentication, disabled Anonymous Auth, enabled impersonation and have changed the app pool to classic instead of integrated pipelining. Everything seems to be configured correctly, however, all the processes launched by the classic ASP site continue to run as the default AppPool identity and not the logged-in user. If it matters, programs are being launched with code such as: set Wsh = Server.CreateObject("WScript.Shell") Wsh.Run("cmd.exe /C mkdir D:\users\foo") Monitoring via Procmon shows cmd.exe being run as either "Classic .NET AppPool" or "DefaultAppPool" depending on the pipeline mode. Any suggestions on how to get the classic ASP site to impersonate and execute as the authenticated user would be great. Thanks!

    Read the article

  • Sharing files between 2 different routers

    - by Chris
    I realize this has been asked before and I have read as much as I could find on the topic but I still need help with this because there are so many different approaches and the ones I am trying aren't working. So I have 2 routers, lets call them A and B. Both have a wireless feature and are active. A is in the basement and receives the internet. There is a TV on the ground floor that is connected to A through an ethernet wire. B is upstairs and gets the internet from A through an ethernet wire. Connected to B, is a desktop running Plex Media Server. What I want to do is make sure devices connected to both routes can access the Plex Media Server. So what I have read is that I should plug in the ethernet wire connecting B to a into a LAN port instead of the WAN port. After that I should turn off DHCP. I have tried this and B stops receiving internet. What am I doing wrong? Another thing I have read is to use Router B in bridge mode but Router B is running openwrt and I have QoS on it so gaming/VoIP/browsing is unaffected by heavy downloading/uploading. I would prefer to keep this active. I realize it might be ineffective if a device in Router A is doing some hardcore downloading but all that stuff is done on Router B anyway so it doesn't matter. Router A can't get openwrt because it is a shitty one provided by Bell. So, how do I proceed with this?

    Read the article

  • The RTL8111/8168B NIC under Linux and the r8168 driver

    - by nik
    So I've got one of the infamous R8168 Realtek ethernet NIC, which have some problems under Linux. After some research, I found out I had to use the r8168 driver for this card (and not the r8169 which still loads when nothing else is available), which I did. So now everything works fine... Sort of. My download and upload rates are more than halved compared to what I should get. When I test (with eg. speedtest) I get something like 20M (often 15M) in download and 30M in upload, but if I test under Windows (everything is otherwise identical: same ethernet cable, same connection, at the same time of the day (well 5 min apart)...), I get 50M upload/download (which is what I expect). Where can it come from? Here's some info: ~ # lspci [...] 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) ~ # modinfo r8168 filename: /lib/modules/3.2.1-gentoo-r2/net/r8168.ko version: 8.027.00-NAPI license: GPL description: RealTek RTL-8168 Gigabit Ethernet driver author: Realtek and the Linux r8168 crew <[email protected]> srcversion: 0A6E9F1D4E8E51DE4B6BEE3 alias: pci:v00001186d00004300sv00001186sd00004B10bc*sc*i* alias: pci:v000010ECd00008168sv*sd*bc*sc*i* depends: vermagic: 3.2.1-gentoo-r2 SMP mod_unload [...] ~ # mii-tool -v eth0: negotiated 100baseTx-HD, link ok product info: vendor 00:07:32, model 17 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

    Read the article

  • Cannot connect to FTP sites anymore

    - by Wayne M
    I have the FTP service running on Server 2003, and I am hosting websites through Apache. I have users configured to point to certain directories on the server. I am using FileZilla to remote FTP, but it never seems to connect to the directory. The command window says: Command: USER wayne Response: 331 Password required for wayne Command: PASS: ***** Response: 230 User wayne logged in Status: Connected Status: Retrieving directory isting... Command: PWD Response: 257 "/wayne" is current directory Command: TYPE I Response: 200 Type set to I. Command: PASV And that's it. It doesn't display any directories at all, and the pane says "Not connected to any server". Sometimes it will display the folder, but nothing happens when I click on it to expand it. It was working fine, and I have another FTP server set up the same way that does work. How can I fix this? EDIT: I've tried changing it to Active FTP, and it says: Command: LIST Command: 150 Opening BINARY mode data connection for /bin/ls Response: 425 Can't open data connection. Error: Failed to retrieve directory listing. I also noticed that I'm not able to browse the site in IIS's management console anymore, it just shows a blank screen when I click on one of the names and says There are no items to show in this view, although the name has permissions to view the folder and everything. Could it be because I have the Web Publishing service disabled (as I'm not using IIS to host websites)? That shouldn't cause anything should it?

    Read the article

  • Best way to 'harden' embedded ext4 file server against unexpected loss of power?

    - by Jeremy Friesner
    Hi all, First, a little background: my company makes an audio streaming device that is a headless, rack-mounted Linux box with a couple of SSDs attached. Each SSD is formatted with ext4. The users can connect to the system using Samba/CIFS to upload new audio files or access existing ones. There is also custom software for streaming out audio over the network. This is all fine. The only problem is that the users are audio people, not computer people, and see the system as a 'black box', not as a computer. Which means that at the end of the day, they aren't going to ssh in to the box and enter "/sbin/shutdown -h"; they are just going to cut power to the rack and leave, and expect things to still work properly the next day. Since ext4 has journalling, journal checksumming, etc, this mostly works. The only time it doesn't work is when someone uploads a new file via Samba and then cuts power to the system before the uploaded data has been fully flushed to the disk. In that case, they come in the next day and find that their new file has been truncated or is missing entirely, and are unhappy. My question is, what is the best way to avoid this problem? Is there a way to get smbd to call "sync" at the end of every upload? (Performance on uploads isn't so important, since they only happen occasionally). Or is there a way to tell ext4 to automatically flush within a few seconds of any change to a file? (Again, performance can be sacrificed for safety here) Should I set a particular write-ordering mode, activate barriers, etc?

    Read the article

  • Struggling to set-up NLB cluster

    - by Chris W
    I'm trying to set up NLB on a couple of Windows 2008 R2 virtual servers running on top of Hyper V R2. The servers each have a single vNIC for LAN access (and a second vNIC for SAN access). I'm setting up the cluster to use Multicast mode. The vNICs are each set to allow MAC spoofing. Essentially I'm finding that i can add SERVER1 as a host and it will pick up and respond to the cluster IP from a remote subnet. If I then 'stop' the node in NLB manager it still responds when I would expect it to stop answering on that IP. If I recreate the cluster and add SERVER2 as the first host, the wizard completes correctly and an IPCONFIG on the server shows that it now has the cluster IP but I can't ping the cluster IP from a remote subnet but I can from another machine on the same subnet. As a final test - with both servers in the cluster, pinging from another machine on the same subnet I still get a response from the cluster IP when both nodes are stopped according to the NLB manager. The two VMs are sat on the same physical blade and are built up exactly the same as they'll be used as SharePoint web front end servers. I'm at a loss as to what could be wrong with the second VM that prevents it taking on the address just as the sole node in the cluster, never mind the strange behaviour of the cluster when I stop/start nodes.

    Read the article

  • Online resizing of kvm guest root filesystem?

    - by Bittrance
    I have a Linux guest that uses an LVM volume directly as root file system (that is, there is no partition table). libvirt config looks thus: <os> <type arch='x86_64' machine='rhel6.4.0'>hvm</type> <kernel>/boot/vmlinuz-X.Y.Z.el6.x86_64</kernel> <initrd>/boot/initramfs-X.Y.Z.el6.x86_64.img</initrd> <cmdline>console=ttyS0 root=/dev/vda</cmdline> <boot dev='hd'/> </os> <disk type='block' device='disk'> <driver name='qemu' type='raw' cache='none' io='native'/> <source dev='/dev/vg/guest'/> <target dev='vda' bus='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </disk> From inside the guest: $ mount /dev/vda on / type ext4 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) tmpfs on /dev/shm type tmpfs (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) Is it possible to resize the guest's root partition without rebooting the guest? Just doing lvextend on the host and resize2fs from the guest does not seem to be enough.

    Read the article

  • Why do I get a DegradedArray event with mdadm

    - by azera
    Hello Just so we're clear on what's happening: I bought 4 new sata 2 drives, with the intent of using them in a raid5 all drive are fully recognised by both my bios and my linux box (gentoo) I created a raid5 array, fiddled a bit with it to understand how it works, how to monitor ect At some point, this triggered a degradedarray event, even though the array is brand new. I tried to stopping the array and recreating a new array with the same drive but the new array starts degraded too. here is what I used to create it mdadm --create -l5 -n4 /dev/md/md0-r5 /dev/sdb /dev/sdd /dev/sde /dev/sdf here are the output from my /proc/mdstat and mdadm --detail --scan **mdstat** Personalities : [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md127 : active raid5 sdf[4] sde[2] sdd[1] sdb[0] 4395415488 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 2.8% (41689732/1465138496) finish=890.3min speed=26645K/sec unused devices: <none> **detail** ARRAY /dev/md/md0-r5 metadata=0.90 spares=1 UUID=453e2833:81f22a74:64188b84:66721085 As such I have a couple questions: does a raid5 array always start in degraded mode at first ? why does sdf have the number 4 between bracket instead of 3, why does it see a spare disk and why is the 4th drive marked with _ instead of U ? (bad configuration ?) How can I recreate the array from scratch, do i have to format each drive on its own before recreating it ? Thanks for any help, I'm not sure about what I should do at the moment

    Read the article

  • SQL Server 2008 R2 - Cannot create database snapshot

    - by Chris Diver
    Server: Windows Server 2008 R2 X64 Enterprise SQL: SQL Server 2008 R2 Enterprise X64 I have a default SQL Server instance, the SQL Server service account is running as a domain user. I am trying to create a database snapshot in the directory where the mdf files are stored. The T-SQL syntax is correct. The file system is NTFS. The error message I get is: Msg 1823, Level 16, State 2, Line 1 A database snapshot cannot be created because it failed to start. Msg 5119, Level 16, State 1, Line 1 Cannot make the file "e:\MSSQL10_50.MSSQLSERVER\MSSQL\DATA\TestDB.ss" a sparse file. Make sure the file system supports sparse files. The local SQLServerMSSQLUser$db$MSSQLSERVER group has Full Control permission on the folder where I am trying to create the snapshot. I can fix the problem in two ways, neither of which are suitable. Add the SQL Server service (domain) account to the local Administrators group and restart the SQL service. Grant the local SQLServerMSSQLUser$db$MSSQLSERVER group Full control on E:\ I have tried to change the owner of the DATA directory to SQLServerMSSQLUser$db$MSSQLSERVER to no avail. I have no issue creating a new database Why can I not create a snapshot by giving permission only on the DATA folder? Update 23/09/2010: I have tried mrdenny's suggestion with no luck (but learned something new in the process), I suspect the problem may be due to the fact that the domain is a windows 2000 domain running in mixed mode. I had to install hotfix KB976494 for Server 2008 R2, as the SQL Server 2008 R2 installer would not verify the service account correctly with the domain. I noticed that Server 2000 isn't a supported operating system for SQL 2008 R2 but cannot find anything that would suggest it shouldn't work in a 2000 domain. I dis-joined the test server from the domain and changed the service accounts to the local service account and I still have the same issue. I will try to re-install the server without joining the domain and without the hotfix and see if the issue persists.

    Read the article

  • Haproxy not properly passing on X-Forwarded-For header

    - by JesseP
    I have backend web servers that receive requests by way of haproxy-nginx-fastcgi. The web app used to see multiple ip's coming through in the X-Forwarded-For header, chained together with commas (most original IP on the left). At some point in the recent past (just noticed, so not sure what caused it) something changed, and now I'm only seeing a single IP passed in the header to my web application. I've tried with haproxy 1.4.21 and 1.4.22 (recent upgrade) with the same behavior. Haproxy has the forwardfor header set: option forwardfor Nginx fastcgi_params config defines this header to be passed to the app: fastcgi_param HTTP_X_FORWARDED_FOR $http_x_forwarded_for; Anyone have any ideas on what might be going wrong here? EDIT: I just started logging the $http_x_forwarded_for variable in nginx logs, and nginx is only ever seeing a single IP, which shouldn't ever be the case, as we should always see our haproxy ip added in there, right? So, issue must either be in nginx handling of the variable coming in, or haproxy not building it properly. I'll keep digging... EDIT #2: I enabled request and response header logging in HAProxy, and it is not spitting anything out for X-Forwarded-For, which seems very odd: Oct 10 10:49:01 newark-lb1 haproxy[19989]: 66.87.95.74:47497 [10/Oct/2012:10:49:01.467] http service/newark2 0/0/0/16/40 301 574 - - ---- 4/4/3/0/0 0/0 {} {} "GET /2zi HTTP/1.1" O Here are the options i set for this in my frontend: mode http option httplog capture request header X-Forwarded-For len 25 capture response header X-Forwarded-For len 25 option httpclose option forwardfor EDIT #3: It really seems like haproxy is munging the header and just passing on a single one to the backend. This is fairly impacting to our production service, so if anyone has an ideas it would be greatly appreciated. I'm stumped... :(

    Read the article

  • Mustek 1200 CP driver SFC4.SYS bluescreens with BAD_POOL_HEADER

    - by Slink84
    I have Windows XP SP2. Recently it started bluescreening right after starting up with 'BAD_POOL_HEADER', 0x00000019 error caused by SFC4.SYS driver. After googling for a while I've found out that this is my Mustek's 1200 CP scanner driver. Booting in safe mode and uninstalling it solved the problem... And created another one: now I can't use my scanner. The weird thing is, that it has been working for a while on this PC without any problems. It all started suddenly, and I can't remember installing anything that might have affected it. Reverting to several earlier system restore points didn't help. I've tried re-installing it from the Mustek website, just in case if my copy got corrupted or infected by a virus, but it did not help - it still bluescreens. Also, I've installed Avast and scanned my PC - there were no viruses found. If anyone had such a problem before or has an idea what might have caused it, please help. ED: @Michael Todd: ...try installing on another PC... I've installed it on my friends PC. He has the same OS version, with the latest updates just like mine (he wasn't too happy, even after I've assured him that it is easy to fix by uninstalling that driver :] ). It worked fine - no bluescreens or whatsoever. So I think I've narrowed it down to either BIOS settings, or some wicked driver conflict. Next thing I'm going to try is to re-install XP, or install windows 7. I'm not too happy with a prospect of mucking about with BIOS settings...

    Read the article

  • Cisco Catalyst 4500 Policy Based Routing

    - by Logan
    In order to test a new firewall I just set up I'm trying to implement policy based routing on our core switch. I want traffic from certain vlans to be routed to the new firewall while everything else continues being routed through the old firewall. I was trying to use this guide. Everything from that guide works fine except trying to run the "ip policy route-map" command in the interface configuration mode. IOS is telling me that such a command doesn't exist. A "show ip interface vlan" command says that policy routing is disabled. Any ideas? Output of "show ver": Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Thu 16-Jul-09 19:49 by prod_rel_team Image text-base: 0x10000000, data-base: 0x11D1E3CC ROM: 12.2(31r)SG2 Dagobah Revision 226, Swamp Revision 34 RTTMCB2223-1 uptime is 3 years, 22 weeks, 2 days, 19 hours, 28 minutes Uptime for this control processor is 51 weeks, 2 days, 18 hours, 2 minutes System returned to ROM by power-on System restarted at 19:22:02 UTC Tue Jul 12 2011 System image file is "bootflash:cat4500-ipbasek9-mz.122-53.sg.bin" ... cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory. Processor board ID FOX103703W3 MPC8245 CPU at 400Mhz, Supervisor V Last reset from PowerUp 42 Virtual Ethernet interfaces 244 Gigabit Ethernet interfaces 511K bytes of non-volatile configuration memory. Configuration register is 0x2

    Read the article

  • App-V Problems After SCCM 2007 SP2 Upgrade

    - by GAThrawn
    We're running an SCCM (MS System Centre Config Manager, successor to SMS) 2007 environment and delivering a number of applications to clients virtualized using App-V 4.5.1. The App-V apps are delivered by SCCM in Download-and-Execute, not streaming mode. The SCCM environment was recently service packed to SCCM 2007 SP2 (amongst other things this gives Win7 support). We also pushed out the updated SCCM clients to our workstations. This seems to have broken file associations for virtual apps for a large number of our users. The users can still open their App-V apps by finding the specific app on their Start Menu and clicking it's icon, but double-clicking an associated file in Explorer, or opening an email attachment gives the "This action is only valid for installed applications" error. There is a Technet blog entry from the App-V team talking about this issue "Upgrade to ConfigMgr 2007 SP2 may break App-V File Type Associations" but running the script there comes back saying "The User Interface option has been updated" but hasn't seemed to fix the problems for any of our users. Unfortunately the Technet blogs don't seem to have comments switched on so you can't see how this has worked out for other people. Anyone else had this problem, have you found any other way to fix it?

    Read the article

  • Using git through cygwin on windows 8

    - by 9point6
    I've got a windows 8 dev preview (not sure if it's relevant, but I never had this hassle on w7) machine and I'm trying to clone a git repo from github. The problem is that my ~/.ssh/id_rsa has 440 permissions and it needs to be 400. I've tried chmodding it but the any changes on the user permissions gets reflected in the group permissions (i.e. chmod 600 results in 660, etc). This appears to be constant throughout any file in the whole filesystem. I've tried messing with the ACLs but to no avail (full control on my user and deny everyone resulted in 000) here's a few outputs to help: $ git clone [removed] Cloning into [removed]... @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: UNPROTECTED PRIVATE KEY FILE! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ Permissions 0660 for '/home/john/.ssh/id_rsa' are too open. It is required that your private key files are NOT accessible by others. This private key will be ignored. bad permissions: ignore key: /home/john/.ssh/id_rsa Permission denied (publickey). fatal: The remote end hung up unexpectedly $ ll ~/.ssh total 6 -r--r----- 1 john None 1675 Nov 30 19:15 id_rsa -rw-rw---- 1 john None 411 Nov 30 19:15 id_rsa.pub -rw-rw-r-- 1 john None 407 Nov 30 18:43 known_hosts $ chmod -v 400 ~/.ssh/id_rsa mode of `/home/john/.ssh/id_rsa' changed from 0440 (r--r-----) to 0400 (r--------) $ ll ~/.ssh total 6 -r--r----- 1 john None 1675 Nov 30 19:15 id_rsa -rw-rw---- 1 john None 411 Nov 30 19:15 id_rsa.pub -rw-rw-r-- 1 john None 407 Nov 30 18:43 known_hosts $ set | grep CYGWIN CYGWIN='sbmntsec ntsec server ntea' I realize I could use msysgit or something, but I'd prefer to be able to do everything from a single terminal Edit: Msysgit doesn't work either for the same reasons

    Read the article

  • How to use different scaling for every monitor?

    - by Mikael Koskinen
    One of the new features in Windows 8.1 is the new "Desktop display scaling", which allows user to configure scaling per monitor. I've been trying to get this working in preview but with no success. If I configure the scaling, it always affects all of my monitors. I have two monitors, the main one with a higher resolution and the secondary with "normal" resolution. The secondary monitor is used in portrait mode. I would like to configure the main monitor's scaling as the text is currently too small. Here's how things look at the configuration screen by default: Now if I adjust the scaling, click apply and do relogin, everything is bigger. On both of my monitors. I haven't clicked the "Let me choose one scaling level for all my displays", but still the slider seems to affect both of them. If I check the "Let me choose one scaling level", the UI changes to look similar to what we have in Windows 8: Still the problem persists. The scaling is applied to both of my monitors. So, it doesn't matter if I check the box or not, the scaling is always applied to all the displays. Any idea how I could get this to work in preview? I've read some comments which seem to indicate that this should work in preview, though Paul Thurrott mentioned at his Winsupersite article that he either didn't get this to work.

    Read the article

  • Access Windows Boot Manager selector when timeout is set to 0?

    - by Kyle Cronin
    I've installed Wubi onto a Windows Vista computer. I've also set the boot timeout to 0: bcdedit /timeout 0 However, now I can't figure out how to get the menu to come up at all! I read on the internets that I had to hold F8 or space when starting up, but they doesn't seem to do anything. Is there a different key or setting I've overlooked? The computer itself is a Dell that's a few months old. The keyboard is USB, but I don't think that's the problem as I can get into the BIOS just fine. Maybe I'm doing it wrong? Am I supposed to hold the keys or rapidly tap them (I've tried both)? If it helps, here's the output from bcdedit: C:\Windows\system32>bcdedit Windows Boot Manager -------------------- identifier {bootmgr} device partition=C: description Windows Boot Manager locale en-US inherit {globalsettings} default {current} resumeobject {5460d9d2-d391-11dc-9d9f-aba67a8797c5} displayorder {current} {e2484fe7-5e97-11de-84d4-0024e8074422} toolsdisplayorder {memdiag} timeout 0 resume No Windows Boot Loader ------------------- identifier {current} device partition=C: path \Windows\system32\winload.exe description Windows Vista locale en-US inherit {bootloadersettings} recoverysequence {572bcd55-ffa7-11d9-aae0-0007e994107d} recoveryenabled Yes osdevice partition=C: systemroot \Windows resumeobject {5460d9d2-d391-11dc-9d9f-aba67a8797c5} nx OptIn Real-mode Boot Sector --------------------- identifier {e2484fe7-5e97-11de-84d4-0024e8074422} device partition=C: path \ubuntu\winboot\wubildr.mbr description Ubuntu

    Read the article

  • Strange windows boot problem - My computer won't boot from hard disk

    - by user29779
    Hello, Until yesterday, I had windows XP installed on my computer. After installing the OS, and setting the BIOS to boot from the hard-disk first, I discovered a strange problem - the OS wasn't booted and the only way I could get it to load was to insert a windows installation disk, enter repair mode, do "fixboot" and restart. The problem only occured when the computer was booted after shut-down. If I only restarted it, everything worked fine. Yesterday, I upgraded my XP to win7 and the problem persists. I tried the same "trick" I did with XP to get it to load, by entering repair and doing "bootrec /fixmbr" and "bootrec /fixboot" but that didn't work (and when I run "scanos" it didn't find any windows installations). Eventually, I got it to load by changing the settings in the BIOS to boot from CD first and HD second, removing the installation disk from the drive, letting it fail to boot from CD and then re-insert the disk. Anyone has any idea what may be the cause or how can I investigate this issue? Thanks! Marina

    Read the article

  • Issue with SSL using HAProxy and Nginx

    - by Ben Chiappetta
    I'm building a highly available site using a multiple HAProxy load balancers, Nginx web serves, and MySQL servers. The site needs to be able to survive load balancer or web servers nodes going offline without any interruption of service to visitors. Currently, I have two boxes running HAProxy sharing a virtual IP using keepalived, which forward to two web servers running Nginx, which then tie into two MySQL boxes using MySQL replication and sharing a virtual IP using heartbeat. Everything is working correctly except for SSL traffic over HAProxy. I'm running version 1.5 dev12 with openssl support compiled in. When I try to navigate to the virtual IP for haproxy over https, I get the message: The plain HTTP request was sent to HTTPS port. Here's my haproxy.cfg so far, which was mainly assembled from other posts: global log 127.0.0.1 local0 log 127.0.0.1 local1 notice # log 127.0.0.1 local0 user haproxy group haproxy daemon maxconn 20000 defaults log global option dontlognull balance leastconn clitimeout 60000 srvtimeout 60000 contimeout 5000 retries 3 option redispatch listen front bind :80 bind :443 ssl crt /etc/pki/tls/certs/cert.pem mode http option http-server-close option forwardfor reqadd X-Forwarded-Proto:\ https if { is_ssl } reqadd X-Proto:\ SSL if { is_ssl } server web01 192.168.25.34 check inter 1s server web02 192.168.25.32 check inter 1s stats enable stats uri /stats stats realm HAProxy\ Statistics stats auth admin:********* Any idea why SSL traffic isn't being passed correctly? Also, any other changes you would recommend? I still need to configure logging, so don't worry about that section. Thanks in advance your help.

    Read the article

  • Cacti is ignoring hash marks in interface aliases

    - by Matt Simmons
    I'm attempting to set up Cacti to monitor a router's interfaces, and I'm having trouble getting the graph templates to show the information that I'd like. Our interface configuration looks like this: interface GigabitEthernet3/6 description WalljackNumber # Server info no ip address no shutdown switchport switchport access vlan 116 switchport mode access ip dhcp snooping trust spanning-tree portfast The "Server Info" string is really just the machine name, and a short relevant description, such as "PolarSprings vmnic2". The important part appears to be that it follows the hashmark. When I run snmpwalk, I get the proper output: IF-MIB::ifAlias.230 = STRING: WalljackNumber # Server info But in Cacti, when I go into the graph templates and set the title to this: |host_description| - Traffic - |query_ifName| (|query_ifAlias|) All that shows up in the graph is: switchname - Traffic - Gi3/6 (WalljackNumber #) Which strikes me as a little weird. What I suppose MAY be happening is that somewhere in the cacti stream, it's interpreting # as being a comment and stripping everything after, but I'm not sure. I was hoping someone could tell me that this was a known documented behavior, or that I could change it in a setting that I wasn't aware of. The alternative answer is to change the delimiter from # to something else, but I've got over a thousand lit switchports on an old college infrastructure, and I'm not sure what else might be relying on them.

    Read the article

  • cron doesn't execute any task, but writes into log as executed

    - by FractalizeR
    I have strange problem on one of my servers. Cron does not execute any task, but it writes to it's log, that task has been executed successfully. Like some simulation mode is activated... Apr 30 03:03:08 nd-10049 crond[13387]: (root) CMD (php /usr/local/frb/backup.php) Apr 30 03:05:01 nd-10049 crond[13397]: (root) CMD (php /home/support/public_html/cron/cron_hourly.php>/home/support/public_html/cron/hourly.log) Apr 30 03:09:01 nd-10049 crond[19108]: (root) CMD (/etc/webmin/cron/tempdelete.pl ) Apr 30 03:10:01 nd-10049 crond[19467]: (root) CMD (php /home/support/public_html/cron/cron_hourly.php>/home/support/public_html/cron/hourly.log) Apr 30 03:14:44 nd-10049 crontab[21154]: (root) BEGIN EDIT (root) Apr 30 03:15:01 nd-10049 crond[21309]: (root) CMD (php /home/support/public_html/cron/cron_hourly.php>/home/support/public_html/cron/hourly.log) Apr 30 03:15:38 nd-10049 crontab[21154]: (root) REPLACE (root) Apr 30 03:15:38 nd-10049 crontab[21154]: (root) END EDIT (root) Apr 30 03:16:01 nd-10049 crond[14961]: (root) RELOAD (cron/root) Apr 30 03:20:02 nd-10049 crond[22620]: (root) CMD (php /home/support/public_html/cron/cron_hourly.php) There are no errors about cron in common log (messages). The OS is CentOS. What can I do to check what is the problem? What can the problem be?

    Read the article

  • Rebuild Apple RAID set

    - by Clinton Blackmore
    We have a Mac Pro tower with an Apple RAID card in it using third party drives. When one drive failed, we replaced it and the RAID 5 set was nearly done rebuilding when the computer was rebooted. It did not come back up. We are now booting up off of a different internal volume, and have three (third-party) drives of identical spec (including revision and firmware) in the box. One of the drives is a global spare; the other two are recognized as belong to a RAID set but are in "Roaming" mode. The intention is to recreate the three-drive RAID set using the data on the two drives that are good. When we tell the system to create a RAID 5 using the three drives, it tells us that it'll create a RAID set but everything will be lost. There are no obvious options to rebuild a RAID using the two good drives and incorporating the third drive in Apple's RAID Utility, and we've looked through the options for the raidutil command. Fortunately, all important data is backed up, and we can rebuild from scratch, but, is there any way to make the RAIDset work again?

    Read the article

  • VBScript Capture StdOut from ShellExecute

    - by Joe
    I am trying to run the following code snippet as part of a tool to gather and log some pertinent system diagnostics. The purpose of this snippet is to gather the result of running the command: vssadmin list writers The snippet is as follows: ' Set WshShell = CreateObject("WScript.Shell") ' WScript.Echo sCurPath & "\vsswritercheck.bat" ' Set WshShellExec = WshShell.Exec("elevate.cmd cmd.exe /c " & sCurPath & "\vsswritercheck.bat") Set oShell = CreateObject("Shell.Application") oShell.ShellExecute "cmd.exe", sCurPath & "\vsswritercheck.bat", , "runas", 1 vsswriter = VSSWriterCheck Select Case oShell.Status Case WshFinished strOutput = oShell.StdOut.ReadAll Case WshFailed strOutput = oShell.StdErr.ReadAll End Select WScript.Echo strOutPut vsswriter = strOutPut With the first code snippet (commented out) I can run the command and capture stdout from the batch file. In the second code snipped, I cannot capture stdout. I need to be able to run the batch script with Elevated permissions, so I am looking for a compromise between the functionality of the two. I cannot run the entire calling script in elevated mode due to restrictions from other pieces of functionality. I am looking for any ideas on how to add this output to my log as I am running out of options that are within the scope of basic scripts.

    Read the article

  • Linux: How do I remove bootchart from the boot process?

    - by java.is.for.desktop
    Hello, everyone! I have OpenSUSE 11.2. I removed bootchart and forgot to run mkinitrd. Now, right at the start of the boot process, I get boot/93-bootchart.sh: line 17: 462 Terminated stopinitrd 5 I Can't find any 93-bootchart.sh anywhere. Failsafe boot mode doesn't help. Earlier I got an error message about non existing /sbin/bootchartd, but I just copied /bin/cat to /sbin/bootchartd using a GParted boot disk. I tried to use chroot with an OpenSUSE boot disk, but mkinitrd can't find the root device, which is there actually (/dev/sda5). How can I make my system boot again? EDIT Ok, now I managed to re-install the bootchart rpm, using OpenSUSE boot disk and chmod. The system starts again. But that annoying bootchart is still there. I will not try again to remove it. First I will try to figure out, how to disable it during the boot process. Hopefully with your help ;)

    Read the article

  • Long access time for static web page on virtual machine

    - by Karol
    My setup Windows 7 on workstation that I use at work (with domain) and home (no domain) Virtual machine (VMWare) that runs Arch Linux (I will call it just "Linux") with network interface in bridged mode. Linux serves web pages with Nginx. IP address of Linux machine is 192.168.0.16 and is added to C:\windows\system32\drivers\etc\hosts: 192.168.0.16 bridged bri IP address of Windows workstation is added to /etc/hosts: 192.168.0.10 workstation I can add more details to my setup description (I am not sure what is relevant). The question Often (but not always) it takes long time for a web browser (Firefox) to open static web page served by Linux. I am sure it is not a performance issue. To be more specific: it takes about ~20 seconds to resolve(?) the address http://bridged for a web browser. Additionally I have just installed samba service and noticed similar problem, so it is not specific to browser & http. Initial access for samba shares also takes long time.

    Read the article

< Previous Page | 501 502 503 504 505 506 507 508 509 510 511 512  | Next Page >