Search Results

Search found 349 results on 14 pages for 'tty'.

Page 1/14 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • How to mount a blu-ray drive?

    - by Stephan Schielke
    Maybe it is for the best to close this question. This has nothing to do with a bluray drive in general anymore. Probably a hardware defect. I will try to test it with a windows system and different cables again... Thx so far. I have a bluray/dvd/cdrom drive with SATA. Ubuntu wont find it under /dev/sd wodim --devices wodim: Overview of accessible drives (1 found) : ------------------------------------------------------------------------- 0 dev='/dev/sg2' rwrw-- : 'HL-DT-ST' 'BDDVDRW CH08LS10' ------------------------------------------------------------------------- cdrecord -scanbus scsibus2: 2,0,0 200) 'HL-DT-ST' 'BDDVDRW CH08LS10' '2.00' Removable CD-ROM fdisk dont even lists it. Ubuntu only automounts blank DVDs, but neither CDROM nor Blurays. I also changed the sata slot, sata cable and the power cable. The drive works with a windows system. This happens when I try to mount: sudo mount -t auto /dev/scd0 /media/bluray mount: you must specify the filesystem type I tried all filesystems there are. I also installed makemkv. It finds the drive but not the disc. Here is my /dev ls -al /dev total 12 drwxr-xr-x 17 root root 4420 2011-11-25 19:36 . drwxr-xr-x 28 root root 4096 2011-11-25 07:12 .. crw------- 1 root root 10, 235 2011-11-25 19:28 autofs -rw-r--r-- 1 root root 630 2011-11-25 19:28 .blkid.tab -rw-r--r-- 1 root root 630 2011-11-25 19:28 .blkid.tab.old drwxr-xr-x 2 root root 700 2011-11-25 19:27 block drwxr-xr-x 2 root root 100 2011-11-25 19:27 bsg crw------- 1 root root 10, 234 2011-11-25 19:28 btrfs-control drwxr-xr-x 3 root root 60 2011-11-25 19:27 bus drwxr-xr-x 2 root root 3820 2011-11-25 19:28 char crw------- 1 root root 5, 1 2011-11-25 19:28 console lrwxrwxrwx 1 root root 11 2011-11-25 19:28 core -> /proc/kcore drwxr-xr-x 2 root root 60 2011-11-25 19:28 cpu crw------- 1 root root 10, 60 2011-11-25 19:28 cpu_dma_latency drwxr-xr-x 7 root root 140 2011-11-25 19:27 disk crw------- 1 root root 10, 61 2011-11-25 19:28 ecryptfs crw-rw---- 1 root video 29, 0 2011-11-25 19:28 fb0 lrwxrwxrwx 1 root root 13 2011-11-25 19:28 fd -> /proc/self/fd crw-rw-rw- 1 root root 1, 7 2011-11-25 19:28 full crw-rw-rw- 1 root fuse 10, 229 2011-11-25 19:28 fuse crw------- 1 root root 251, 0 2011-11-25 19:28 hidraw0 crw------- 1 root root 251, 1 2011-11-25 19:28 hidraw1 crw------- 1 root root 10, 228 2011-11-25 19:28 hpet lrwxrwxrwx 1 root root 14 2011-11-25 19:27 .initramfs -> /run/initramfs drwxr-xr-x 4 root root 220 2011-11-25 19:28 input crw------- 1 root root 1, 11 2011-11-25 19:28 kmsg srw-rw-rw- 1 root root 0 2011-11-25 19:28 log brw-rw---- 1 root disk 7, 0 2011-11-25 19:28 loop0 brw-rw---- 1 root disk 7, 1 2011-11-25 19:28 loop1 brw-rw---- 1 root disk 7, 2 2011-11-25 19:28 loop2 brw-rw---- 1 root disk 7, 3 2011-11-25 19:28 loop3 brw-rw---- 1 root disk 7, 4 2011-11-25 19:28 loop4 brw-rw---- 1 root disk 7, 5 2011-11-25 19:28 loop5 brw-rw---- 1 root disk 7, 6 2011-11-25 19:28 loop6 brw-rw---- 1 root disk 7, 7 2011-11-25 19:28 loop7 drwxr-xr-x 2 root root 60 2011-11-25 19:27 mapper crw------- 1 root root 10, 227 2011-11-25 19:28 mcelog crw-r----- 1 root kmem 1, 1 2011-11-25 19:28 mem drwxr-xr-x 2 root root 60 2011-11-25 19:27 net crw------- 1 root root 10, 59 2011-11-25 19:28 network_latency crw------- 1 root root 10, 58 2011-11-25 19:28 network_throughput crw-rw-rw- 1 root root 1, 3 2011-11-25 19:28 null crw-rw-rw- 1 root root 195, 0 2011-11-25 19:28 nvidia0 crw-rw-rw- 1 root root 195, 255 2011-11-25 19:28 nvidiactl crw------- 1 root root 1, 12 2011-11-25 19:28 oldmem crw-r----- 1 root kmem 1, 4 2011-11-25 19:28 port crw------- 1 root root 108, 0 2011-11-25 19:28 ppp crw------- 1 root root 10, 1 2011-11-25 19:28 psaux crw-rw-rw- 1 root tty 5, 2 2011-11-25 20:00 ptmx drwxr-xr-x 2 root root 0 2011-11-25 19:27 pts brw-rw---- 1 root disk 1, 0 2011-11-25 19:28 ram0 brw-rw---- 1 root disk 1, 1 2011-11-25 19:28 ram1 brw-rw---- 1 root disk 1, 10 2011-11-25 19:28 ram10 brw-rw---- 1 root disk 1, 11 2011-11-25 19:28 ram11 brw-rw---- 1 root disk 1, 12 2011-11-25 19:28 ram12 brw-rw---- 1 root disk 1, 13 2011-11-25 19:28 ram13 brw-rw---- 1 root disk 1, 14 2011-11-25 19:28 ram14 brw-rw---- 1 root disk 1, 15 2011-11-25 19:28 ram15 brw-rw---- 1 root disk 1, 2 2011-11-25 19:28 ram2 brw-rw---- 1 root disk 1, 3 2011-11-25 19:28 ram3 brw-rw---- 1 root disk 1, 4 2011-11-25 19:28 ram4 brw-rw---- 1 root disk 1, 5 2011-11-25 19:28 ram5 brw-rw---- 1 root disk 1, 6 2011-11-25 19:28 ram6 brw-rw---- 1 root disk 1, 7 2011-11-25 19:28 ram7 brw-rw---- 1 root disk 1, 8 2011-11-25 19:28 ram8 brw-rw---- 1 root disk 1, 9 2011-11-25 19:28 ram9 crw-rw-rw- 1 root root 1, 8 2011-11-25 19:28 random crw-rw-r--+ 1 root root 10, 62 2011-11-25 19:28 rfkill lrwxrwxrwx 1 root root 4 2011-11-25 19:28 rtc -> rtc0 crw------- 1 root root 254, 0 2011-11-25 19:28 rtc0 lrwxrwxrwx 1 root root 3 2011-11-25 19:38 scd0 -> sr0 brw-rw---- 1 root disk 8, 0 2011-11-25 19:28 sda brw-rw---- 1 root disk 8, 1 2011-11-25 19:28 sda1 brw-rw---- 1 root disk 8, 2 2011-11-25 19:28 sda2 brw-rw---- 1 root disk 8, 3 2011-11-25 19:28 sda3 brw-rw---- 1 root disk 8, 5 2011-11-25 19:28 sda5 brw-rw---- 1 root disk 8, 6 2011-11-25 19:28 sda6 brw-rw---- 1 root disk 8, 16 2011-11-25 19:28 sdb brw-rw---- 1 root disk 8, 17 2011-11-25 19:28 sdb1 crw-rw---- 1 root disk 21, 0 2011-11-25 19:28 sg0 crw-rw---- 1 root disk 21, 1 2011-11-25 19:28 sg1 crw-rw----+ 1 root cdrom 21, 2 2011-11-25 19:28 sg2 lrwxrwxrwx 1 root root 8 2011-11-25 19:28 shm -> /run/shm crw------- 1 root root 10, 231 2011-11-25 19:28 snapshot drwxr-xr-x 4 root root 280 2011-11-25 19:28 snd brw-rw----+ 1 root cdrom 11, 0 2011-11-25 19:38 sr0 lrwxrwxrwx 1 root root 15 2011-11-25 19:28 stderr -> /proc/self/fd/2 lrwxrwxrwx 1 root root 15 2011-11-25 19:28 stdin -> /proc/self/fd/0 lrwxrwxrwx 1 root root 15 2011-11-25 19:28 stdout -> /proc/self/fd/1 crw-rw-rw- 1 root tty 5, 0 2011-11-25 19:35 tty crw--w---- 1 root tty 4, 0 2011-11-25 19:28 tty0 crw------- 1 root root 4, 1 2011-11-25 19:28 tty1 crw--w---- 1 root tty 4, 10 2011-11-25 19:28 tty10 crw--w---- 1 root tty 4, 11 2011-11-25 19:28 tty11 crw--w---- 1 root tty 4, 12 2011-11-25 19:28 tty12 crw--w---- 1 root tty 4, 13 2011-11-25 19:28 tty13 crw--w---- 1 root tty 4, 14 2011-11-25 19:28 tty14 crw--w---- 1 root tty 4, 15 2011-11-25 19:28 tty15 crw--w---- 1 root tty 4, 16 2011-11-25 19:28 tty16 crw--w---- 1 root tty 4, 17 2011-11-25 19:28 tty17 crw--w---- 1 root tty 4, 18 2011-11-25 19:28 tty18 crw--w---- 1 root tty 4, 19 2011-11-25 19:28 tty19 crw------- 1 root root 4, 2 2011-11-25 19:28 tty2 crw--w---- 1 root tty 4, 20 2011-11-25 19:28 tty20 crw--w---- 1 root tty 4, 21 2011-11-25 19:28 tty21 crw--w---- 1 root tty 4, 22 2011-11-25 19:28 tty22 crw--w---- 1 root tty 4, 23 2011-11-25 19:28 tty23 crw--w---- 1 root tty 4, 24 2011-11-25 19:28 tty24 crw--w---- 1 root tty 4, 25 2011-11-25 19:28 tty25 crw--w---- 1 root tty 4, 26 2011-11-25 19:28 tty26 crw--w---- 1 root tty 4, 27 2011-11-25 19:28 tty27 crw--w---- 1 root tty 4, 28 2011-11-25 19:28 tty28 crw--w---- 1 root tty 4, 29 2011-11-25 19:28 tty29 crw------- 1 root root 4, 3 2011-11-25 19:28 tty3 crw--w---- 1 root tty 4, 30 2011-11-25 19:28 tty30 crw--w---- 1 root tty 4, 31 2011-11-25 19:28 tty31 crw--w---- 1 root tty 4, 32 2011-11-25 19:28 tty32 crw--w---- 1 root tty 4, 33 2011-11-25 19:28 tty33 crw--w---- 1 root tty 4, 34 2011-11-25 19:28 tty34 crw--w---- 1 root tty 4, 35 2011-11-25 19:28 tty35 crw--w---- 1 root tty 4, 36 2011-11-25 19:28 tty36 crw--w---- 1 root tty 4, 37 2011-11-25 19:28 tty37 crw--w---- 1 root tty 4, 38 2011-11-25 19:28 tty38 crw--w---- 1 root tty 4, 39 2011-11-25 19:28 tty39 crw------- 1 root root 4, 4 2011-11-25 19:28 tty4 crw--w---- 1 root tty 4, 40 2011-11-25 19:28 tty40 crw--w---- 1 root tty 4, 41 2011-11-25 19:28 tty41 crw--w---- 1 root tty 4, 42 2011-11-25 19:28 tty42 crw--w---- 1 root tty 4, 43 2011-11-25 19:28 tty43 crw--w---- 1 root tty 4, 44 2011-11-25 19:28 tty44 crw--w---- 1 root tty 4, 45 2011-11-25 19:28 tty45 crw--w---- 1 root tty 4, 46 2011-11-25 19:28 tty46 crw--w---- 1 root tty 4, 47 2011-11-25 19:28 tty47 crw--w---- 1 root tty 4, 48 2011-11-25 19:28 tty48 crw--w---- 1 root tty 4, 49 2011-11-25 19:28 tty49 crw------- 1 root root 4, 5 2011-11-25 19:28 tty5 crw--w---- 1 root tty 4, 50 2011-11-25 19:28 tty50 crw--w---- 1 root tty 4, 51 2011-11-25 19:28 tty51 crw--w---- 1 root tty 4, 52 2011-11-25 19:28 tty52 crw--w---- 1 root tty 4, 53 2011-11-25 19:28 tty53 crw--w---- 1 root tty 4, 54 2011-11-25 19:28 tty54 crw--w---- 1 root tty 4, 55 2011-11-25 19:28 tty55 crw--w---- 1 root tty 4, 56 2011-11-25 19:28 tty56 crw--w---- 1 root tty 4, 57 2011-11-25 19:28 tty57 crw--w---- 1 root tty 4, 58 2011-11-25 19:28 tty58 crw--w---- 1 root tty 4, 59 2011-11-25 19:28 tty59 crw------- 1 root root 4, 6 2011-11-25 19:28 tty6 crw--w---- 1 root tty 4, 60 2011-11-25 19:28 tty60 crw--w---- 1 root tty 4, 61 2011-11-25 19:28 tty61 crw--w---- 1 root tty 4, 62 2011-11-25 19:28 tty62 crw--w---- 1 root tty 4, 63 2011-11-25 19:28 tty63 crw--w---- 1 root tty 4, 7 2011-11-25 19:28 tty7 crw--w---- 1 root tty 4, 8 2011-11-25 19:28 tty8 crw--w---- 1 root tty 4, 9 2011-11-25 19:28 tty9 crw------- 1 root root 5, 3 2011-11-25 19:28 ttyprintk crw-rw---- 1 root dialout 4, 64 2011-11-25 19:28 ttyS0 crw-rw---- 1 root dialout 4, 65 2011-11-25 19:28 ttyS1 crw-rw---- 1 root dialout 4, 74 2011-11-25 19:28 ttyS10 crw-rw---- 1 root dialout 4, 75 2011-11-25 19:28 ttyS11 crw-rw---- 1 root dialout 4, 76 2011-11-25 19:28 ttyS12 crw-rw---- 1 root dialout 4, 77 2011-11-25 19:28 ttyS13 crw-rw---- 1 root dialout 4, 78 2011-11-25 19:28 ttyS14 crw-rw---- 1 root dialout 4, 79 2011-11-25 19:28 ttyS15 crw-rw---- 1 root dialout 4, 80 2011-11-25 19:28 ttyS16 crw-rw---- 1 root dialout 4, 81 2011-11-25 19:28 ttyS17 crw-rw---- 1 root dialout 4, 82 2011-11-25 19:28 ttyS18 crw-rw---- 1 root dialout 4, 83 2011-11-25 19:28 ttyS19 crw-rw---- 1 root dialout 4, 66 2011-11-25 19:28 ttyS2 crw-rw---- 1 root dialout 4, 84 2011-11-25 19:28 ttyS20 crw-rw---- 1 root dialout 4, 85 2011-11-25 19:28 ttyS21 crw-rw---- 1 root dialout 4, 86 2011-11-25 19:28 ttyS22 crw-rw---- 1 root dialout 4, 87 2011-11-25 19:28 ttyS23 crw-rw---- 1 root dialout 4, 88 2011-11-25 19:28 ttyS24 crw-rw---- 1 root dialout 4, 89 2011-11-25 19:28 ttyS25 crw-rw---- 1 root dialout 4, 90 2011-11-25 19:28 ttyS26 crw-rw---- 1 root dialout 4, 91 2011-11-25 19:28 ttyS27 crw-rw---- 1 root dialout 4, 92 2011-11-25 19:28 ttyS28 crw-rw---- 1 root dialout 4, 93 2011-11-25 19:28 ttyS29 crw-rw---- 1 root dialout 4, 67 2011-11-25 19:28 ttyS3 crw-rw---- 1 root dialout 4, 94 2011-11-25 19:28 ttyS30 crw-rw---- 1 root dialout 4, 95 2011-11-25 19:28 ttyS31 crw-rw---- 1 root dialout 4, 68 2011-11-25 19:28 ttyS4 crw-rw---- 1 root dialout 4, 69 2011-11-25 19:28 ttyS5 crw-rw---- 1 root dialout 4, 70 2011-11-25 19:28 ttyS6 crw-rw---- 1 root dialout 4, 71 2011-11-25 19:28 ttyS7 crw-rw---- 1 root dialout 4, 72 2011-11-25 19:28 ttyS8 crw-rw---- 1 root dialout 4, 73 2011-11-25 19:28 ttyS9 d rwxr-xr-x 3 root root 60 2011-11-25 19:28 .udev crw-r----- 1 root root 10, 223 2011-11-25 19:28 uinput crw-rw-rw- 1 root root 1, 9 2011-11-25 19:28 urandom drwxr-xr-x 2 root root 60 2011-11-25 19:27 usb crw------- 1 root root 252, 0 2011-11-25 19:28 usbmon0 crw------- 1 root root 252, 1 2011-11-25 19:28 usbmon1 crw------- 1 root root 252, 2 2011-11-25 19:28 usbmon2 crw------- 1 root root 252, 3 2011-11-25 19:28 usbmon3 crw------- 1 root root 252, 4 2011-11-25 19:28 usbmon4 crw------- 1 root root 252, 5 2011-11-25 19:28 usbmon5 crw------- 1 root root 252, 6 2011-11-25 19:28 usbmon6 crw------- 1 root root 252, 7 2011-11-25 19:28 usbmon7 crw------- 1 root root 252, 8 2011-11-25 19:28 usbmon8 drwxr-xr-x 4 root root 80 2011-11-25 19:28 v4l crw------- 1 root root 10, 57 2011-11-25 19:28 vboxdrv crw------- 1 root root 10, 56 2011-11-25 19:28 vboxnetctl drwxr-x--- 4 root vboxusers 80 2011-11-25 19:28 vboxusb crw-rw---- 1 root tty 7, 0 2011-11-25 19:28 vcs crw-rw---- 1 root tty 7, 1 2011-11-25 19:28 vcs1 crw-rw---- 1 root tty 7, 2 2011-11-25 19:28 vcs2 crw-rw---- 1 root tty 7, 3 2011-11-25 19:28 vcs3 crw-rw---- 1 root tty 7, 4 2011-11-25 19:28 vcs4 crw-rw---- 1 root tty 7, 5 2011-11-25 19:28 vcs5 crw-rw---- 1 root tty 7, 6 2011-11-25 19:28 vcs6 crw-rw---- 1 root tty 7, 128 2011-11-25 19:28 vcsa crw-rw---- 1 root tty 7, 129 2011-11-25 19:28 vcsa1 crw-rw---- 1 root tty 7, 130 2011-11-25 19:28 vcsa2 crw-rw---- 1 root tty 7, 131 2011-11-25 19:28 vcsa3 crw-rw---- 1 root tty 7, 132 2011-11-25 19:28 vcsa4 crw-rw---- 1 root tty 7, 133 2011-11-25 19:28 vcsa5 crw-rw---- 1 root tty 7, 134 2011-11-25 19:28 vcsa6 crw------- 1 root root 10, 63 2011-11-25 19:28 vga_arbiter crw-rw----+ 1 root video 81, 0 2011-11-25 19:28 video0 crw-rw-rw- 1 root root 1, 5 2011-11-25 19:28 zero sg_scan -i gives me: sudo sg_scan -i /dev/sg0: scsi0 channel=0 id=0 lun=0 [em] ATA ST31000524NS SN12 [rmb=0 cmdq=0 pqual=0 pdev=0x0] /dev/sg1: scsi0 channel=0 id=1 lun=0 [em] ATA WDC WD15EADS-00S 01.0 [rmb=0 cmdq=0 pqual=0 pdev=0x0] /dev/sg2: scsi2 channel=0 id=0 lun=0 [em] HL-DT-ST BDDVDRW CH08LS10 2.00 [rmb=1 cmdq=0 pqual=0 pdev=0x5] sg_map gives me: /dev/sg0 /dev/sda /dev/sg1 /dev/sdb /dev/sg2 /dev/scd0 lsscsi -l gives me: [0:0:0:0] disk ATA ST31000524NS SN12 /dev/sda state=running queue_depth=1 scsi_level=6 type=0 device_blocked=0 timeout=30 [0:0:1:0] disk ATA WDC WD15EADS-00S 01.0 /dev/sdb state=running queue_depth=1 scsi_level=6 type=0 device_blocked=0 timeout=30 [2:0:0:0] cd/dvd HL-DT-ST BDDVDRW CH08LS10 2.00 /dev/sr0 state=running queue_depth=1 scsi_level=6 type=5 device_blocked=0 timeout=30 my udf mod is: filename: /lib/modules/3.0.0-14-generic/kernel/fs/udf/udf.ko license: GPL description: Universal Disk Format Filesystem author: Ben Fennema srcversion: 6ABDE012374D96B9685B8E5 depends: crc-itu-t vermagic: 3.0.0-14-generic SMP mod_unload modversions Do I need special drivers or mods enabled? Do I need to change some BIOS settings? edit: Somehow I am now able to fire the mount command without any filesystem errors, but now I get: mount: no medium found on /dev/sr0

    Read the article

  • Bricked - tty mode incorrect, terminal disabled, unity broken

    - by user989805
    After installing VirtualBox unity seems to be uninstalled.. Launcher and task bar are missing. I can't access terminal from the normal ctrl alt T command. I tried logging into TTY mode but it says my login is incorrect. I am trying to login with my normal ubuntu username and password. I have searched for solutions but since I dont have terminal or TTY I cant bash out any commands, and I have tried safeboot but the root terminal always says it cant run whatever command I enter. I am really lost and I am trying to avoid a fresh install :( I greatly and genuinely appreciate any help! This is the computer I use for college!

    Read the article

  • Ubuntu 12.10 TTY console (Ctrl+Alt+F[1-6]) not working

    - by Vanessa Deagan
    I've been a Ubuntu user for some time now. I have a very annoying problem, I have no idea what causes it, and I haven't managed to find anything relevant after Googling like crazy. The problem is my TTY consoles are not working. Usually, these are activated using CTRL ALT F[1-6]. It was working when I was using the Nouveau drivers, but after installing the nVidia proprietary drivers, instead of getting a terminal console I get a strange monochrome pattern that slowly fades away. Does anyone know how to get CTRL + ALT + F[1-6] working again?

    Read the article

  • Disk errors on tty and syslog/dmesg

    - by Shoaibi
    Recently I have started to get a lot of these errors: Jun 18 08:57:42 abacus kernel: [ 401.554292] ata5: SError: { HostInt 10B8B } Jun 18 08:57:42 abacus kernel: [ 401.559346] sr 4:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 Jun 18 08:57:42 abacus kernel: [ 401.560191] ata5.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Jun 18 08:57:42 abacus kernel: [ 401.560231] res 51/20:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error) Jun 18 08:57:42 abacus kernel: [ 401.575310] ata5.00: status: { DRDY ERR } Jun 18 08:57:42 abacus kernel: [ 401.579801] ata5: hard resetting link Jun 18 08:57:42 abacus kernel: [ 401.929320] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Jun 18 08:57:42 abacus kernel: [ 401.941936] ata5.00: configured for UDMA/100 Jun 18 08:57:42 abacus kernel: [ 401.969426] ata5: EH complete Jun 18 08:57:54 abacus kernel: [ 413.527699] ata5.00: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x6 Jun 18 08:57:54 abacus kernel: [ 413.527779] ata5.00: irq_stat 0x40000001 Jun 18 08:57:54 abacus kernel: [ 413.527822] ata5: SError: { HostInt 10B8B } Jun 18 08:57:54 abacus kernel: [ 413.527901] sr 4:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 Jun 18 08:57:54 abacus kernel: [ 413.528103] ata5.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Jun 18 08:57:54 abacus kernel: [ 413.528142] res 51/20:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error) Jun 18 08:57:54 abacus kernel: [ 413.528184] ata5.00: status: { DRDY ERR } Jun 18 08:57:54 abacus kernel: [ 413.528303] ata5: hard resetting link Jun 18 08:57:54 abacus kernel: [ 413.875894] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Jun 18 08:57:54 abacus kernel: [ 413.888267] ata5.00: configured for UDMA/100 Jun 18 08:57:54 abacus kernel: [ 413.916365] ata5: EH complete Jun 18 08:57:56 abacus kernel: [ 415.537834] ata5.00: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x6 Jun 18 08:57:56 abacus kernel: [ 415.545253] ata5.00: irq_stat 0x40000001 Jun 18 08:57:56 abacus kernel: [ 415.549788] ata5: SError: { HostInt 10B8B } Jun 18 08:57:56 abacus kernel: [ 415.554840] sr 4:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 Jun 18 08:57:56 abacus kernel: [ 415.555201] ata5.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Jun 18 08:57:56 abacus kernel: [ 415.555242] res 51/20:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error) Jun 18 08:57:56 abacus kernel: [ 415.570483] ata5.00: status: { DRDY ERR } Jun 18 08:57:56 abacus kernel: [ 415.574695] ata5: hard resetting link Jun 18 08:57:56 abacus kernel: [ 415.924954] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Jun 18 08:57:56 abacus kernel: [ 415.936831] ata5.00: configured for UDMA/100 Jun 18 08:57:56 abacus kernel: [ 415.965001] ata5: EH complete Jun 18 08:58:02 abacus kernel: [ 421.529784] ata5.00: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x6 Jun 18 08:58:02 abacus kernel: [ 421.529904] ata5.00: irq_stat 0x40000001 Jun 18 08:58:02 abacus kernel: [ 421.530023] ata5: SError: { HostInt 10B8B } Jun 18 08:58:02 abacus kernel: [ 421.530104] sr 4:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 Jun 18 08:58:02 abacus kernel: [ 421.530425] ata5.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Jun 18 08:58:02 abacus kernel: [ 421.530466] res 51/20:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error) Jun 18 08:58:02 abacus kernel: [ 421.530583] ata5.00: status: { DRDY ERR } Jun 18 08:58:02 abacus kernel: [ 421.530705] ata5: hard resetting link Jun 18 08:58:02 abacus kernel: [ 421.873218] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Jun 18 08:58:02 abacus kernel: [ 421.885040] ata5.00: configured for UDMA/100 Jun 18 08:58:02 abacus kernel: [ 421.913404] ata5: EH complete Are these critical error messages? What would be the cause and remedy?

    Read the article

  • TTY with 256 colors?

    - by timn
    With URxvt and xterm it is possible to use a virtual terminal supporting 256 colors instead of only eight. Since my Intel GMA graphics card is well-supported by the KMS framebuffer driver, I am exclusively working on the TTY. Unfortunately it only supports eight colors although with MPlayer (-vo fbdev/fbdev2) and other framebuffer tools far more can be addressed. Is there a way to tell the TTY to use more than eight colors?

    Read the article

  • TTY Resolution in Xubuntu 9.10

    - by Zurahn
    I've exhausted my ability to search through Google for this, so I'm giving it a go here. What I'm trying to do is increase the resolution (or decrease the font size) in the TTY terminals. Xubuntu 9.10 uses GRUB2, and everywhere I can find directs me to edit the /etc/default/grub File in order to add vga=XXX to the GRUB_CMDLINE_LINUX value, and this simply doesn't work. Out of endless fiddling with the file, nothing ever seems to change. On my Netbook running an earlier version, I had success with this command dpkg-reconfigure console-setup But once again it yields no change. Got any ideas?

    Read the article

  • Fedora, ssh and sudo

    - by Ricky Robinson
    I have to run a script remotely on several Fedora machines through ssh. Since the script requires root priviliges, I do: $ ssh [email protected]_host "sudo touch test_sudo" #just a simple example sudo: no tty present and no askpass program specified The remote machines are configured in such a way that the password for sudo is never asked for. For the above error, the most common fix is to allocate a pseudo-terminal with the -t option in ssh: $ ssh -t [email protected]_host "sudo touch test_sudo" sudo: no tty present and no askpass program specified Let's try to force this allocation with -t -t: $ ssh -t -t [email protected]_host "sudo touch test_sudo" sudo: no tty present and no askpass program specified Nope, it doesn't work. In /etc/sudoers of course I have this line: #Defaults requiretty ... but I can't manually change it on tens of remote machines. Am I missing something here? Is there an easy fix? EDIT: Here is the sudoers file of a host where ssh [email protected] "sudo stat ." works. Here is the sudoers file of a host where it doesn't work. EDIT 2: Running tty on a host where it works: $ ssh [email protected]_ok tty not a tty $ ssh -t [email protected]_ok tty /dev/pts/12 Connection to host_ok closed. $ ssh -t -t [email protected]_ok tty /dev/pts/12 Connection to host_ok closed. Now on a host where it doesn't work: $ ssh [email protected]_ko tty not a tty $ ssh -t [email protected]_ko tty not a tty Connection to host_ko closed. $ ssh -t -t [email protected]_ko tty not a tty Connection to host_ko closed.

    Read the article

  • How can I restart compiz from tty? (& Related, how can I set up a fallback WM?)

    - by Jon
    So I'm testing Natty, and Compiz keeps crashing on me. I expect this sort of thing from alpha software, of course, but it doesn't always give me the option to restart compiz, and for some reason doesn't have a fallback WM configured. Without a window manager, all my programs are still running, but they're not accepting input from the keyboard, and I can't switch between them. I can, however, press Ctrl+Alt+F1 and get a terminal, and I can killall Xorg to reset everything, but I'd rather just reset compiz if possible. If I try typing compiz --replace there in the tty, it complains "fatal--couldn't open display." Is there a way to have tty1 restart compiz? Like compiz --replace --display=something? Additionally, is there a way to configure a fallback window manager so that there's an easier way to recover from compiz crashing?

    Read the article

  • run script as another user from a root script with no tty stdin

    - by viktor tron
    Using CentOs, I want to run a script as user 'training' as a system service. I use daemontools to monitor the process, which needs a launcher script that is run as root and has no tty standard in. Below I give my four different attempts which all fail. : #!/bin/bash exec >> /var/log/training_service.log 2>&1 setuidgid training training_command This last line is not good enough since for training_command, we need environment for trqaining user to be set. : su - training -c 'training_command' This looks like it (http://serverfault.com/questions/44400/run-a-shell-script-as-a-different-user) but gives 'standard in must be tty' as su making sure tty is present to potentially accept password. I know I could make this disappear by modifying /etc/sudoers (a la http://superuser.com/questions/119376/bash-su-script-giving-an-error-standard-in-must-be-a-tty) but i am reluctant and unsure of consequences. : runuser - training -c 'training_command' This one gives runuser: cannot set groups: Connection refused. I found no sense or resolution to this error. : ssh -p100 [email protected] 'source $HOME/.bashrc; training_command' This one is more of a joke to show desparation. Even this one fails with Host key verification failed. (the host key IS in known_hosts, etc). Note: all of 2,3,4 work as they should if I run the wrapper script from a root shell. problems only occur if the system service monitor (daemontools) launches it (no tty terminal I guess). I am stuck. Is this something so hard to achieve? I appreciate all insight and guidance to best practice. (this has also been posted on superuser: http://superuser.com/questions/434235/script-calling-script-as-other-user)

    Read the article

  • Configuration to point an X tty to a separate system?

    - by buu700
    Specifically, I have an Ubuntu 10.04 system with a headless Ubuntu 12.04 virtual machine, and I'm looking for a way to have it set up so pressing ctrl+alt+F8 will take me into another X client which is connected to an X server on the vm (with gdm appropriately displayed at startup, etc.). As in, my startup script should spin up the headless machine and then immediately perform a "startx" pointed at the vm.

    Read the article

  • Link between low level drivers and tty drivers

    - by agent.smith
    I was writing a console driver for linux and I came across the tty interface that I need to set up for this driver. I got confused as to how tty drivers are bound with low-level drivers. Many times the root file system already contains a lot of tty devices. I am wondering how low-level devices can bind to one of the existing tty nodes on the root file system. For example, /dev/tty7 : Node on the root file system. How does a low-level device driver connect with this node? Or should that low-level device define a completely new tty device?

    Read the article

  • How would I go about writing a Linux TTY sniffer?

    - by alienate
    For educational purposes (not that anyone should care the motivations behind such an exercise) I'd like to write a program that can read/write to/from alternate tty/pty's. I've read papers (from the 1990's) but can't employ the implementation they use, on modern UNIXes. I was hoping that someone had researched into this in the past, or at least, read documentation pertaining to it, that they could provide. I also wonder if (considering the fact that Linux doesn't have STREAMs) if this exercise must be done via a loadable kernel module? I have many questions and probably a misunderstanding of some of the fundamental ideologies that allow such objectives to be put in place, could someone help? :)

    Read the article

  • Using the full tty real estate with sqlplus

    - by katsumii
    I believe 'rlwrap' is widely used for adding 'sqlplus' the history function and command line editing. 'rlwrap' has other functions and here's my kludgy alias to force sqlplus to use the full real estate of yourtty. Be it PuTTy session from Windows or Linux gnome terminal. $ declare -f sqlplus sqlplus () { PRE_TEXT=$(resize |sed -n "1s/COLUMNS=/set linesize /p;2s/LINES=/set pagesize /p"|while read line; do printf "%s \ " "$line";done); if [ -z "$1" ]; then rlwrap -m -P "$PRE_TEXT" sqlplus /nolog; else if ! echo $1 | grep '^-' > /dev/null; then rlwrap -m -P "$PRE_TEXT connect $*" sqlplus /nolog; else command sqlplus $*; fi; fi }

    Read the article

  • How do I get my blacked out ttys back?

    - by con-f-use
    Original Question: After I replaced my Ubuntu 10.10 with 11.04 all I get when I Strg+Alt+F1-6 into a tty is a black screen. Also when I boot there's a while of black screen after grub2 menu is displayed. Then until just before gnome starts it stays black. I have an Nvida Geforce Quadro FX 770M on my HP EliteBook 8530w. How do I get my ttys (aka 'virtual terminals') to work again? My effords in chronological order: So grub and gfx-payload seems to be the problem, I figured. I went along with this guide for higher tty resolution. Which led to the grub2 menu displaying in my native resolution rather than 800x600. The black screen problem remains. I googlehit some bugreports on other nvidia crads having that problem. I tried uninstalling the nvidia driver. No effect. Also tried different resolutions With an older version of the kernel it works. Though not perfectly. The ttys are usable, black screen between grub2 menu and gnome start remains. Not really a solution. Tried so much, that I lost track. Reinstalled grub2 and linux-image-2.6.38-8-generic. Then did this to my /etc/default/grub in accordance with the aforementioned guide (/etc/grub.d/00_header edited as well): GRUB_DEFAULT=0 GRUB_HIDDEN_TIMEOUT=0 #GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=3 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` #GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" GRUB_GFXMODE=1680x1050x32 To my surprise I can now use my ttys in native resolution. Black screen between grub2 menu and gnome login screen is still there though. That is annoying since I also use an encrypted disk thus having to enter my passphrase in total dark... Still looking for a solution but urgency is low. Downloaded and installed a later version of nvidia driver. No difference to last edit. Tried GRUB_CMDLINE_LINUX="vga="-parameter. No effect. nomodeset has no effect. not even in combination with vga=... Tried echo FRAMEBUFFER=y > /etc/initramfs-tools/conf.d/splash no effect (see comment) On the verge of resignation... Bounty period soon to end.

    Read the article

  • I cannot login into any TTYs

    - by Lucio
    My system is Ubuntu 11.10. When I enter into any tty (1, 2, 3..) it ask me my login name and password but I can not move forward. It say that the info isn't correct. I have a user without password called world, so I enter world but it show me this Module invalid (or similar) The problems is that I must enter a command and I can't. There isn't any way to fix or an alternative way to enter the command?

    Read the article

  • Getting a TTY in a Connectback Shell

    - by Asad R.
    I'm often asked by friends to help with small Linux problems, and more often than not I'm required to login to the remote system. Usually there are a lot of issues with making an account and logging in (sometimes the box is behind a NAT device, sometimes SSHD isn't installed, etc.) so I usually just ask them to make a connect-back shell using netcat (nc -e /bin/bash ). If they don't have netcat I can just ask them to grab a copy of a statically compiled binary which isn't that hard or time consuming to download and run. Though this works well enough for me to enter simple commands, I can't run any apps that require a tty (vi, for example) and can't use any job control functions. I managed to bypass this issue by running in.telnetd with a few arguments within the connect-back shell that would assign me a terminal and drop me to a shell. Unfortunately in.telnetd isn't usually installed by default on most systems. What's the easiest way to get a fully functional connect-back terminal shell without requiring any non-standard packages? (A small C program that does the job would be fine as well, I just can't seem to find much documentation on how a TTY is assigned/allocated. A solution that doesn't require me to plough through the source code for SSHD and TELNETD would be nice :))

    Read the article

  • Running a program on boot without login, using the screen

    - by configurator
    Preface: I have a server running on an old laptop. The screen is always on with a login prompt, but because its keyboard is in pretty bad shape, I use it exclusively via ssh. The screen is in a good position, though; I want to use it to display a clock and some stats about what my server is doing. I have scripts to display all those things, but I want to always show them on the monitor screen. My question is, how do I get my script (called HUD) to run on /dev/tty1, instead of the login prompt. Hopefully, it should be possible to accept keyboard input as well as display its output, so that it can use the keyboard to show more info where needed in a future version. I'd also like tty2 etc. to remain active as login screens, in face I actually do need to login locally. For a start, I tried creating a script that I can run from ssh to start the HUD. It goes something like this: ( flock -n 9 watch --interval 0.2 --precise --color --notitle --exec /path/to/script & disown ) 9> /var/lock/hud > /dev/tty1 2> /dev/tty1 < /dev/tty1 (I had to use & disown instead of nohup because nohup recognized the tty and redirects output to nohup.out instead.) This sort-of works. However, it has a few issues: It doesn't steal the terminal's keyboard input, so you can't ctrl+c to get out of it (nor change the script to actually use the keyboard input), and if you press enter it show it and scrolls the display, never refreshing it correctly afterwards. Oddly, if I disconnect the ssh session which created it, it stops working and shows a message: exec: No such file or directory. If I reconnect to ssh, it resumes functioning properly. It feels hackish. Is there a better way to do this? How?

    Read the article

  • Paramiko and Pseudo-tty Allocation

    - by Jon
    I'm trying to use Paramiko to connect to a remote host and execute a number of text file substitutions. i, o, e = client.exec_command("perl -p -i -e 's/" + initial + "/" + replaced + "/g'" + conf); Some of these commands need to be run as sudo, which results in: sudo: sorry, you must have a tty to run sudo I can force pseudo-tty allocation with the -t switch and ssh. Is it possible to do the same thing using paramiko?

    Read the article

  • using python Paramiko for ssh: sudo: no tty present and no askpass program specified

    - by misteryes
    I want to use paramiko to ssh into a bunch a remote nodes and run some command line with root priviledge I have ssh key in my home directory and so i don't need to input password when I ssh into those remote nodes but when running the following script: def connect(hostname): ssh = paramiko.SSHClient() ssh.set_missing_host_key_policy(paramiko.AutoAddPolicy()) ssh.connect(hostname, username='niky', pkey=paramiko.RSAKey.from_private_key(open('id_rsa'), 'passwd'), timeout = 240.0) return ssh def run(hostname): ssh = connect(hostname) (stdin, stdout, stderr) = ssh.exec_command("sudo ls") res = stderr.readlines() print hostname+': '+''.join(str(elem) for elem in res)+'\n' run(remote.nity.com) I got the following error: remote.nity.com: sudo: no tty present and no askpass program specified if I don't add sudo before ls everything works fine what are potential reasons ? thanks!

    Read the article

  • Best practices to avoid Jenkins error: sudo: no tty present and no askpass program specified

    - by s g
    When running any sudo command from Jenkins I get the following error: sudo: no tty present and no askpass program specified I understand that I can solve this by adding a NOPASSWD entry to my /etc/sudoers file which will allow user jenkins to run commands without needing a password. I can add an entry like this: %jenkins ALL=(ALL)NOPASSWD:/home/vts_share/test/sudotest.sh ...but this leads to the following issue: how to avoid specifying full path in sudoers file? I can add an entry like this: %jenkins ALL=NOPASSWD: ALL ...but this allows user jenkins to avoid the password prompt for all commands, which seems a bit unsafe. I'm just curious what my options are here, and if there are any best practices I should consider.

    Read the article

  • Reading Serial Data From C (OSX /dev/tty)

    - by Jud Stephenson
    I am trying to read data from a bluetooth barcode scanner (KDC300) using C. Here is the code I have so far, and the program successfully establishes a bluetooth connection to the scanner, but when a barcode is scanned, no input is displayed on the screen (Eventually more will be done with the data, but we have to get it working first, right). Here is the program: #include <stdio.h> #include <stdlib.h> #include <string.h> #include <unistd.h> #include <fcntl.h> #include <errno.h> #include <termios.h> #include <sys/ioctl.h> int main (int argc, const char * argv[]) { // define vars int STOP = 0; //char buf[255]; if(argv[1]) { int fd = open("/dev/tty.KDC1", O_RDONLY); if(fd == -1) { printf("%s", strcat("Unable to open /dev/tty.", argv[1])); } int res; while(STOP == 0) { while((res = read(fd,buf,255)) == 0); { if(res > 0) { buf[res]=0; printf("%s:%d\n", buf, res); if(buf[sizeof(buf)]=='\n') break; } } } } return 0; } If anyone has any ideas, I am at a loss on this so far. If it is any help, I can run screen /dev/tty.KDC1 and any barcodes scanned on the scanner appear in the terminal, I just can't do anything with the data. Jud

    Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >