Search Results

Search found 11003 results on 441 pages for 'usb storage'.

Page 1/441 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • External HDD USB 3.0 failure

    - by Philip
    [ 2560.376113] usb 9-1: new high-speed USB device number 2 using xhci_hcd [ 2560.376186] usb 9-1: Device not responding to set address. [ 2560.580136] usb 9-1: Device not responding to set address. [ 2560.784104] usb 9-1: device not accepting address 2, error -71 [ 2560.840127] hub 9-0:1.0: unable to enumerate USB device on port 1 [ 2561.080182] usb 10-1: new SuperSpeed USB device number 5 using xhci_hcd [ 2566.096163] usb 10-1: device descriptor read/8, error -110 [ 2566.200096] usb 10-1: new SuperSpeed USB device number 5 using xhci_hcd [ 2571.216175] usb 10-1: device descriptor read/8, error -110 [ 2571.376138] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2571.744174] usb 10-1: new SuperSpeed USB device number 7 using xhci_hcd [ 2576.760116] usb 10-1: device descriptor read/8, error -110 [ 2576.864074] usb 10-1: new SuperSpeed USB device number 7 using xhci_hcd [ 2581.880153] usb 10-1: device descriptor read/8, error -110 [ 2582.040123] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2582.224139] hub 9-0:1.0: unable to enumerate USB device on port 1 [ 2582.464177] usb 10-1: new SuperSpeed USB device number 9 using xhci_hcd [ 2587.480122] usb 10-1: device descriptor read/8, error -110 [ 2587.584079] usb 10-1: new SuperSpeed USB device number 9 using xhci_hcd [ 2592.600150] usb 10-1: device descriptor read/8, error -110 [ 2592.760134] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2593.128175] usb 10-1: new SuperSpeed USB device number 11 using xhci_hcd [ 2598.144183] usb 10-1: device descriptor read/8, error -110 [ 2598.248109] usb 10-1: new SuperSpeed USB device number 11 using xhci_hcd [ 2603.264171] usb 10-1: device descriptor read/8, error -110 [ 2603.480157] usb 10-1: new SuperSpeed USB device number 12 using xhci_hcd [ 2608.496162] usb 10-1: device descriptor read/8, error -110 [ 2608.600091] usb 10-1: new SuperSpeed USB device number 12 using xhci_hcd [ 2613.616166] usb 10-1: device descriptor read/8, error -110 [ 2613.832170] usb 10-1: new SuperSpeed USB device number 13 using xhci_hcd [ 2618.848135] usb 10-1: device descriptor read/8, error -110 [ 2618.952079] usb 10-1: new SuperSpeed USB device number 13 using xhci_hcd [ 2623.968155] usb 10-1: device descriptor read/8, error -110 [ 2624.184176] usb 10-1: new SuperSpeed USB device number 14 using xhci_hcd [ 2629.200124] usb 10-1: device descriptor read/8, error -110 [ 2629.304075] usb 10-1: new SuperSpeed USB device number 14 using xhci_hcd [ 2634.320172] usb 10-1: device descriptor read/8, error -110 [ 2634.424135] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2634.776186] usb 10-1: new SuperSpeed USB device number 15 using xhci_hcd [ 2639.792105] usb 10-1: device descriptor read/8, error -110 [ 2639.896090] usb 10-1: new SuperSpeed USB device number 15 using xhci_hcd [ 2644.912172] usb 10-1: device descriptor read/8, error -110 [ 2645.128174] usb 10-1: new SuperSpeed USB device number 16 using xhci_hcd [ 2650.144160] usb 10-1: device descriptor read/8, error -110 [ 2650.248062] usb 10-1: new SuperSpeed USB device number 16 using xhci_hcd [ 2655.264120] usb 10-1: device descriptor read/8, error -110 [ 2655.480182] usb 10-1: new SuperSpeed USB device number 17 using xhci_hcd [ 2660.496121] usb 10-1: device descriptor read/8, error -110 [ 2660.600086] usb 10-1: new SuperSpeed USB device number 17 using xhci_hcd [ 2665.616167] usb 10-1: device descriptor read/8, error -110 [ 2665.832177] usb 10-1: new SuperSpeed USB device number 18 using xhci_hcd [ 2670.848110] usb 10-1: device descriptor read/8, error -110 [ 2670.952066] usb 10-1: new SuperSpeed USB device number 18 using xhci_hcd [ 2675.968081] usb 10-1: device descriptor read/8, error -110 [ 2676.072124] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2786.104531] xhci_hcd 0000:02:00.0: remove, state 4 [ 2786.104546] usb usb10: USB disconnect, device number 1 [ 2786.104686] xHCI xhci_drop_endpoint called for root hub [ 2786.104692] xHCI xhci_check_bandwidth called for root hub [ 2786.104942] xhci_hcd 0000:02:00.0: USB bus 10 deregistered [ 2786.105054] xhci_hcd 0000:02:00.0: remove, state 4 [ 2786.105065] usb usb9: USB disconnect, device number 1 [ 2786.105176] xHCI xhci_drop_endpoint called for root hub [ 2786.105181] xHCI xhci_check_bandwidth called for root hub [ 2786.109787] xhci_hcd 0000:02:00.0: USB bus 9 deregistered [ 2786.110134] xhci_hcd 0000:02:00.0: PCI INT A disabled [ 2794.268445] pci 0000:02:00.0: [1b73:1000] type 0 class 0x000c03 [ 2794.268483] pci 0000:02:00.0: reg 10: [mem 0x00000000-0x0000ffff] [ 2794.268689] pci 0000:02:00.0: PME# supported from D0 D3hot [ 2794.268700] pci 0000:02:00.0: PME# disabled [ 2794.276383] pci 0000:02:00.0: BAR 0: assigned [mem 0xd7800000-0xd780ffff] [ 2794.276398] pci 0000:02:00.0: BAR 0: set to [mem 0xd7800000-0xd780ffff] (PCI address [0xd7800000-0xd780ffff]) [ 2794.276419] pci 0000:02:00.0: no hotplug settings from platform [ 2794.276658] xhci_hcd 0000:02:00.0: enabling device (0000 -> 0002) [ 2794.276675] xhci_hcd 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 2794.276762] xhci_hcd 0000:02:00.0: setting latency timer to 64 [ 2794.276771] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 2794.276913] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 9 [ 2794.395760] xhci_hcd 0000:02:00.0: irq 16, io mem 0xd7800000 [ 2794.396141] xHCI xhci_add_endpoint called for root hub [ 2794.396144] xHCI xhci_check_bandwidth called for root hub [ 2794.396195] hub 9-0:1.0: USB hub found [ 2794.396203] hub 9-0:1.0: 1 port detected [ 2794.396305] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 2794.396371] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 10 [ 2794.396496] xHCI xhci_add_endpoint called for root hub [ 2794.396499] xHCI xhci_check_bandwidth called for root hub [ 2794.396547] hub 10-0:1.0: USB hub found [ 2794.396553] hub 10-0:1.0: 1 port detected [ 2798.004084] usb 1-3: new high-speed USB device number 8 using ehci_hcd [ 2798.140824] scsi21 : usb-storage 1-3:1.0 [ 2820.176116] usb 1-3: reset high-speed USB device number 8 using ehci_hcd [ 2824.000526] scsi 21:0:0:0: Direct-Access BUFFALO HD-PZU3 0001 PQ: 0 ANSI: 6 [ 2824.002263] sd 21:0:0:0: Attached scsi generic sg2 type 0 [ 2824.003617] sd 21:0:0:0: [sdb] 1953463728 512-byte logical blocks: (1.00 TB/931 GiB) [ 2824.005139] sd 21:0:0:0: [sdb] Write Protect is off [ 2824.005149] sd 21:0:0:0: [sdb] Mode Sense: 1f 00 00 08 [ 2824.009084] sd 21:0:0:0: [sdb] No Caching mode page present [ 2824.009094] sd 21:0:0:0: [sdb] Assuming drive cache: write through [ 2824.011944] sd 21:0:0:0: [sdb] No Caching mode page present [ 2824.011952] sd 21:0:0:0: [sdb] Assuming drive cache: write through [ 2824.049153] sdb: sdb1 [ 2824.051814] sd 21:0:0:0: [sdb] No Caching mode page present [ 2824.051821] sd 21:0:0:0: [sdb] Assuming drive cache: write through [ 2824.051825] sd 21:0:0:0: [sdb] Attached SCSI disk [ 2839.536624] usb 1-3: USB disconnect, device number 8 [ 2844.620178] usb 10-1: new SuperSpeed USB device number 2 using xhci_hcd [ 2844.640281] scsi22 : usb-storage 10-1:1.0 [ 2850.326545] scsi 22:0:0:0: Direct-Access BUFFALO HD-PZU3 0001 PQ: 0 ANSI: 6 [ 2850.327560] sd 22:0:0:0: Attached scsi generic sg2 type 0 [ 2850.329561] sd 22:0:0:0: [sdb] 1953463728 512-byte logical blocks: (1.00 TB/931 GiB) [ 2850.329889] sd 22:0:0:0: [sdb] Write Protect is off [ 2850.329897] sd 22:0:0:0: [sdb] Mode Sense: 1f 00 00 08 [ 2850.330223] sd 22:0:0:0: [sdb] No Caching mode page present [ 2850.330231] sd 22:0:0:0: [sdb] Assuming drive cache: write through [ 2850.331414] sd 22:0:0:0: [sdb] No Caching mode page present [ 2850.331423] sd 22:0:0:0: [sdb] Assuming drive cache: write through [ 2850.384116] usb 10-1: USB disconnect, device number 2 [ 2850.392050] sd 22:0:0:0: [sdb] Unhandled error code [ 2850.392056] sd 22:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2850.392061] sd 22:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 2850.392074] end_request: I/O error, dev sdb, sector 0 [ 2850.392079] quiet_error: 70 callbacks suppressed [ 2850.392082] Buffer I/O error on device sdb, logical block 0 [ 2850.392194] ldm_validate_partition_table(): Disk read failed. [ 2850.392271] Dev sdb: unable to read RDB block 0 [ 2850.392377] sdb: unable to read partition table [ 2850.392581] sd 22:0:0:0: [sdb] READ CAPACITY failed [ 2850.392584] sd 22:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2850.392588] sd 22:0:0:0: [sdb] Sense not available. [ 2850.392613] sd 22:0:0:0: [sdb] Asking for cache data failed [ 2850.392617] sd 22:0:0:0: [sdb] Assuming drive cache: write through [ 2850.392621] sd 22:0:0:0: [sdb] Attached SCSI disk [ 2850.732182] usb 10-1: new SuperSpeed USB device number 3 using xhci_hcd [ 2850.752228] scsi23 : usb-storage 10-1:1.0 [ 2851.752709] scsi 23:0:0:0: Direct-Access BUFFALO HD-PZU3 0001 PQ: 0 ANSI: 6 [ 2851.754481] sd 23:0:0:0: Attached scsi generic sg2 type 0 [ 2851.756576] sd 23:0:0:0: [sdb] 1953463728 512-byte logical blocks: (1.00 TB/931 GiB) [ 2851.758426] sd 23:0:0:0: [sdb] Write Protect is off [ 2851.758436] sd 23:0:0:0: [sdb] Mode Sense: 1f 00 00 08 [ 2851.758779] sd 23:0:0:0: [sdb] No Caching mode page present [ 2851.758787] sd 23:0:0:0: [sdb] Assuming drive cache: write through [ 2851.759968] sd 23:0:0:0: [sdb] No Caching mode page present [ 2851.759977] sd 23:0:0:0: [sdb] Assuming drive cache: write through [ 2851.817710] sdb: sdb1 [ 2851.820562] sd 23:0:0:0: [sdb] No Caching mode page present [ 2851.820568] sd 23:0:0:0: [sdb] Assuming drive cache: write through [ 2851.820572] sd 23:0:0:0: [sdb] Attached SCSI disk [ 2852.060352] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.076533] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.076538] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.196329] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.212593] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.212599] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.456290] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.472402] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.472408] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.624304] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.640531] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.640536] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.772296] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.788536] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.788541] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.920349] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.936536] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.936540] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2853.072287] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2853.088565] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2853.088570] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.176339] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.192561] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.192567] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.320349] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.336526] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.336531] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.468344] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.484551] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.484556] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.612349] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.628540] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.628545] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.756350] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.772528] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.772533] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.848116] usb 10-1: USB disconnect, device number 3 [ 2884.851493] scsi 23:0:0:0: [sdb] killing request [ 2884.851501] scsi 23:0:0:0: [sdb] killing request [ 2884.851699] scsi 23:0:0:0: [sdb] Unhandled error code [ 2884.851702] scsi 23:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2884.851708] scsi 23:0:0:0: [sdb] CDB: Read(10): 28 00 00 5f 2b ee 00 00 3e 00 [ 2884.851721] end_request: I/O error, dev sdb, sector 6237166 [ 2884.851726] Buffer I/O error on device sdb1, logical block 6237102 [ 2884.851730] Buffer I/O error on device sdb1, logical block 6237103 [ 2884.851738] Buffer I/O error on device sdb1, logical block 6237104 [ 2884.851741] Buffer I/O error on device sdb1, logical block 6237105 [ 2884.851744] Buffer I/O error on device sdb1, logical block 6237106 [ 2884.851747] Buffer I/O error on device sdb1, logical block 6237107 [ 2884.851750] Buffer I/O error on device sdb1, logical block 6237108 [ 2884.851753] Buffer I/O error on device sdb1, logical block 6237109 [ 2884.851757] Buffer I/O error on device sdb1, logical block 6237110 [ 2884.851807] scsi 23:0:0:0: [sdb] Unhandled error code [ 2884.851810] scsi 23:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2884.851813] scsi 23:0:0:0: [sdb] CDB: Read(10): 28 00 00 5f 2c 2c 00 00 3e 00 [ 2884.851824] end_request: I/O error, dev sdb, sector 6237228 [ 2885.168190] usb 10-1: new SuperSpeed USB device number 4 using xhci_hcd [ 2885.188268] scsi24 : usb-storage 10-1:1.0 Please help me with my problem. I got this after running dmesg.

    Read the article

  • usb mouse/keyboard doesn't work with 3.11.0-12-generic kernel

    - by x-yuri
    I can't use my usb keyboard/mouse after upgrade from raring to saucy. The keyboard works in grub menu and if I boot with the previous kernel version (3.8.0-31-generic). My new kernel version is 3.11.0-12-generic. I've got Mad Catz R.A.T.7 wired USB mouse, Canyon CNL-MBMSO02 wired usb mouse and Logitech diNovo Edge wireless keyboard, connected to computer through Logitech Unifying Receiver. Using PS/2 keyboard I've managed to get some information. dmesg says: [ 0.166273] ACPI: bus type USB registered [ 0.166273] usbcore: registered new interface driver usbfs [ 0.166273] usbcore: registered new interface driver hub [ 0.166273] usbcore: registered new device driver usb ... [ 3.534226] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.534228] ehci-pci: EHCI PCI platform driver [ 3.534291] ehci-pci 0000:00:1a.7: setting latency timer to 64 [ 3.534299] ehci-pci 0000:00:1a.7: EHCI Host Controller [ 3.534304] ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 3.534315] ehci-pci 0000:00:1a.7: debug port 1 [ 3.538218] ehci-pci 0000:00:1a.7: cache line size of 64 is not supported [ 3.538231] ehci-pci 0000:00:1a.7: irq 18, io mem 0xd3325400 [ 3.548017] ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 3.548042] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.548045] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.548048] usb usb1: Product: EHCI Host Controller [ 3.548050] usb usb1: Manufacturer: Linux 3.11.0-12-generic ehci_hcd [ 3.548053] usb usb1: SerialNumber: 0000:00:1a.7 [ 3.548155] hub 1-0:1.0: USB hub found [ 3.548159] hub 1-0:1.0: 6 ports detected [ 3.548311] ehci-pci 0000:00:1d.7: setting latency timer to 64 [ 3.548319] ehci-pci 0000:00:1d.7: EHCI Host Controller [ 3.548323] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 3.548333] ehci-pci 0000:00:1d.7: debug port 1 [ 3.552228] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported [ 3.552239] ehci-pci 0000:00:1d.7: irq 23, io mem 0xd3325000 [ 3.564014] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 3.564044] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.564047] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.564050] usb usb2: Product: EHCI Host Controller [ 3.564052] usb usb2: Manufacturer: Linux 3.11.0-12-generic ehci_hcd [ 3.564056] usb usb2: SerialNumber: 0000:00:1d.7 [ 3.564163] hub 2-0:1.0: USB hub found [ 3.564167] hub 2-0:1.0: 6 ports detected [ 3.564274] ehci-platform: EHCI generic platform driver [ 3.564280] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.564281] ohci-platform: OHCI generic platform driver [ 3.564287] uhci_hcd: USB Universal Host Controller Interface driver [ 3.564345] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 3.564347] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 3.564352] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 3.564378] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000f0c0 [ 3.564402] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.564404] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.564406] usb usb3: Product: UHCI Host Controller [ 3.564408] usb usb3: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.564410] usb usb3: SerialNumber: 0000:00:1a.0 [ 3.564478] hub 3-0:1.0: USB hub found [ 3.564482] hub 3-0:1.0: 2 ports detected [ 3.564589] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 3.564592] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 3.564597] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 3.564623] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000f0a0 [ 3.564647] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.564649] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.564651] usb usb4: Product: UHCI Host Controller [ 3.564653] usb usb4: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.564654] usb usb4: SerialNumber: 0000:00:1a.1 [ 3.564727] hub 4-0:1.0: USB hub found [ 3.564730] hub 4-0:1.0: 2 ports detected [ 3.564834] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 3.564837] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 3.564843] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 3.564863] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000f080 [ 3.564885] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.564887] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.564889] usb usb5: Product: UHCI Host Controller [ 3.564891] usb usb5: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.564892] usb usb5: SerialNumber: 0000:00:1a.2 [ 3.564962] hub 5-0:1.0: USB hub found [ 3.564966] hub 5-0:1.0: 2 ports detected [ 3.565073] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 3.565076] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 3.565081] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 3.565101] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000f060 [ 3.565124] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.565127] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.565128] usb usb6: Product: UHCI Host Controller [ 3.565130] usb usb6: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.565132] usb usb6: SerialNumber: 0000:00:1d.0 [ 3.565195] hub 6-0:1.0: USB hub found [ 3.565198] hub 6-0:1.0: 2 ports detected [ 3.565303] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 3.565306] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 3.565310] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 3.565329] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000f040 [ 3.565352] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.565354] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.565356] usb usb7: Product: UHCI Host Controller [ 3.565358] usb usb7: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.565359] usb usb7: SerialNumber: 0000:00:1d.1 [ 3.565424] hub 7-0:1.0: USB hub found [ 3.565427] hub 7-0:1.0: 2 ports detected [ 3.565534] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 3.565537] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 3.565541] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 3.565560] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000f020 [ 3.565584] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.565587] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.565588] usb usb8: Product: UHCI Host Controller [ 3.565590] usb usb8: Manufacturer: Linux 3.11.0-12-generic uhci_hcd [ 3.565592] usb usb8: SerialNumber: 0000:00:1d.2 [ 3.565658] hub 8-0:1.0: USB hub found [ 3.565661] hub 8-0:1.0: 2 ports detected ... [ 4.120014] usb 2-3: new high-speed USB device number 2 using ehci-pci ... [ 4.468908] usb 2-3: New USB device found, idVendor=046d, idProduct=0825 [ 4.468912] usb 2-3: New USB device strings: Mfr=0, Product=0, SerialNumber=2 [ 4.468914] usb 2-3: SerialNumber: AF582E10 ... [ 5.284019] usb 5-2: new full-speed USB device number 2 using uhci_hcd [ 5.465903] usb 5-2: New USB device found, idVendor=046d, idProduct=0b04 [ 5.465908] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.465911] usb 5-2: Product: Logitech BT Mini-Receiver [ 5.465914] usb 5-2: Manufacturer: Logitech [ 5.468948] hub 5-2:1.0: USB hub found [ 5.470898] hub 5-2:1.0: 3 ports detected [ 5.476096] Switched to clocksource tsc [ 5.712099] usb 7-2: new full-speed USB device number 2 using uhci_hcd [ 5.896366] usb 7-2: New USB device found, idVendor=046d, idProduct=c52b [ 5.896370] usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.896372] usb 7-2: Product: USB Receiver [ 5.896374] usb 7-2: Manufacturer: Logitech [ 6.140016] usb 8-1: new full-speed USB device number 2 using uhci_hcd [ 6.324597] usb 8-1: New USB device found, idVendor=0738, idProduct=1708 [ 6.324603] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 6.324605] usb 8-1: Product: Mad Catz R.A.T.7 Mouse [ 6.324608] usb 8-1: Manufacturer: Mad Catz [ 6.564012] usb 8-2: new low-speed USB device number 3 using uhci_hcd [ 6.746602] usb 8-2: New USB device found, idVendor=1d57, idProduct=0010 [ 6.746608] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 6.746610] usb 8-2: Product: usb mouse with wheel [ 6.746613] usb 8-2: Manufacturer: HID-Compliant Mouse [ 7.337898] usb 5-2.2: new full-speed USB device number 3 using uhci_hcd [ 7.490902] usb 5-2.2: New USB device found, idVendor=046d, idProduct=c713 [ 7.490907] usb 5-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.490910] usb 5-2.2: Product: Logitech BT Mini-Receiver [ 7.490913] usb 5-2.2: Manufacturer: Logitech [ 7.490915] usb 5-2.2: SerialNumber: 001F203BD6A7 [ 7.569898] usb 5-2.3: new full-speed USB device number 4 using uhci_hcd [ 7.722901] usb 5-2.3: New USB device found, idVendor=046d, idProduct=c714 [ 7.722906] usb 5-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.722909] usb 5-2.3: Product: Logitech BT Mini-Receiver [ 7.722911] usb 5-2.3: Manufacturer: Logitech [ 7.722913] usb 5-2.3: SerialNumber: 001F203BD6A7 lsusb (more output): Bus 002 Device 002: ID 046d:0825 Logitech, Inc. Webcam C270 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 003: ID 1d57:0010 Xenta Bus 008 Device 002: ID 0738:1708 Mad Catz, Inc. Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 002: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 004: ID 046d:c714 Logitech, Inc. diNovo Edge Keyboard Bus 005 Device 003: ID 046d:c713 Logitech, Inc. Bus 005 Device 002: ID 046d:0b04 Logitech, Inc. Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub More background. Before that I had a problem with logging in to GNOME. During which I upgraded all the packages at one point (apt-get upgrade) and it stopped booting at all (it didn't get to login screen). Then I fixed PATH issue and now I've got this usb-not-working issue. I tried reinstalling kernel, to no effect. Is there anything else I can do to fix or diagnose the problem?

    Read the article

  • HSDPA modem only working on certain USB ports

    - by nabulke
    Depending on which USB port I use to connect my HSDPA modem, the network manager will connect to the internet or not. I used to work (i.e. established a internet connection automatically) on all ports, but over time it simply stopped on some ports. lsusb output in all cases looks like that (Device ID varies depending on USB port): Bus 001 Device 009: ID 12d1:1003 Huawei Technologies Co., Ltd. E220 HSDPA Modem / E270 HSDPA/HSUPA Modem Any ideas what could cause this behaviour? What can I do to fix this? ADDED One additional information about the modem: if connected via USB it will be available as as harddrive AND as a HSDPA modem (kind of a duality...). In the error case, it will only be shown as a harddrive. ADDITIONAL INFO AS REQUESTED MODEM NOT WORKING Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 413c:8000 Dell Computer Corp. BC02 Bluetooth Adapter Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 007: ID 12d1:1003 Huawei Technologies Co., Ltd. E220 HSDPA Modem / E270 HSDPA/HSUPA Modem Bus 001 Device 005: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 004: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB Bus 001 Device 003: ID 413c:0058 Dell Computer Corp. Port Replicator Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub laptop:~$ dmesg | grep 'usb' [ 0.225371] usbcore: registered new interface driver usbfs [ 0.225387] usbcore: registered new interface driver hub [ 0.225418] usbcore: registered new device driver usb [ 0.504291] usb usb1: configuration #1 chosen from 1 choice [ 0.504767] usb usb2: configuration #1 chosen from 1 choice [ 0.505046] usb usb3: configuration #1 chosen from 1 choice [ 0.505601] usb usb4: configuration #1 chosen from 1 choice [ 1.061064] usb 1-6: new high speed USB device using ehci_hcd and address 3 [ 1.192636] usb 1-6: configuration #1 chosen from 1 choice [ 1.447006] usb 2-2: new full speed USB device using uhci_hcd and address 2 [ 1.634908] usb 2-2: configuration #1 chosen from 1 choice [ 1.708164] usb 1-6.1: new high speed USB device using ehci_hcd and address 4 [ 1.801668] usb 1-6.1: configuration #1 chosen from 1 choice [ 2.076279] usb 1-6.1.1: new low speed USB device using ehci_hcd and address 5 [ 2.174932] usb 1-6.1.1: configuration #1 chosen from 1 choice [ 6.580315] usb 1-6.1.2: new high speed USB device using ehci_hcd and address6 [ 6.683479] usb 1-6.1.2: configuration #1 chosen from 1 choice [ 20.018671] usbcore: registered new interface driver btusb [ 20.131703] usbcore: registered new interface driver usb-storage [ 20.131988] usb-storage: device found at 6 [ 20.131991] usb-storage: waiting for device to settle before scanning [ 20.207981] usb 1-6.1.2: USB disconnect, address 6 [ 20.291499] usbcore: registered new interface driver hiddev [ 20.297052] input: Logitech USB Mouse as /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6.1/1-6.1.1/1-6.1.1:1.0/input/input6 [ 20.297465] generic-usb 0003:046D:C00C.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:1d.7-6.1.1/input0 [ 20.297534] usbcore: registered new interface driver usbhid [ 20.297803] usbhid: v2.6:USB HID core driver [ 26.552360] usb 1-6.1.2: new high speed USB device using ehci_hcd and address 7 [ 26.663506] usb 1-6.1.2: configuration #1 chosen from 1 choice [ 26.709628] usb-storage: device found at 7 [ 26.709631] usb-storage: waiting for device to settle before scanning [ 26.732387] usb-storage: device found at 7 [ 26.732390] usb-storage: waiting for device to settle before scanning [ 31.709568] usb-storage: device scan complete [ 31.733676] usb-storage: device scan complete MODEM WORKING Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 413c:8000 Dell Computer Corp. BC02 Bluetooth Adapter Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 12d1:1003 Huawei Technologies Co., Ltd. E220 HSDPA Modem / E270 HSDPA/HSUPA Modem Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub dmesg | grep 'usb' [ 0.134811] usbcore: registered new interface driver usbfs [ 0.134826] usbcore: registered new interface driver hub [ 0.134858] usbcore: registered new device driver usb [ 0.360327] usb usb1: configuration #1 chosen from 1 choice [ 0.360783] usb usb2: configuration #1 chosen from 1 choice [ 0.361061] usb usb3: configuration #1 chosen from 1 choice [ 0.361611] usb usb4: configuration #1 chosen from 1 choice [ 1.144122] usb 2-2: new full speed USB device using uhci_hcd and address 2 [ 1.346896] usb 2-2: configuration #1 chosen from 1 choice [ 1.588072] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 1.761204] usb 3-1: configuration #1 chosen from 1 choice [ 5.972042] usb 1-1: new high speed USB device using ehci_hcd and address 4 [ 6.115438] usb 1-1: configuration #1 chosen from 1 choice [ 19.990565] usbcore: registered new interface driver usbserial [ 19.991429] usb-storage: device found at 4 [ 19.991432] usb-storage: waiting for device to settle before scanning [ 20.017260] usbcore: registered new interface driver usb-storage [ 20.017305] usbcore: registered new interface driver usbserial_generic [ 20.017308] usbserial: USB Serial Driver core [ 20.017817] usb-storage: device found at 4 [ 20.017820] usb-storage: waiting for device to settle before scanning [ 20.070796] usbcore: registered new interface driver btusb [ 20.229525] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0 [ 20.229776] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 [ 20.229843] usbcore: registered new interface driver option [ 20.230396] usbcore: registered new interface driver hiddev [ 20.246280] input: Logitech USB Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input6 [ 20.246438] generic-usb 0003:046D:C00C.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:1d.1-1/input0 [ 20.246479] usbcore: registered new interface driver usbhid [ 20.246483] usbhid: v2.6:USB HID core driver [ 25.436579] usb-storage: device scan complete [ 25.437674] usb-storage: device scan complete

    Read the article

  • USB external drive is not recognized by any OS, how to troubleshoot in Ubuntu?

    - by Breno
    First of all I would like to inform you that I saw a question similar to mine but the error was different, so here's my problem... I have an external HD samsung s2 model of 500GB and a day to day just stopped working, tried in other systems (windows and mac) however are not recognized. In the windows device manager when I insert the usb it states that the device in question are not working properly. Well, in the logs of my ubuntu 4.12 I see the following message when I insert my usb device in: [ 2967.560216] usb 7-2: new full-speed USB device number 2 using uhci_hcd [ 2967.680182] usb 7-2: device descriptor read/64, error -71 [ 2967.904176] usb 7-2: device descriptor read/64, error -71 [ 2968.120227] usb 7-2: new full-speed USB device number 3 using uhci_hcd [ 2968.240207] usb 7-2: device descriptor read/64, error -71 [ 2968.464063] usb 7-2: device descriptor read/64, error -71 [ 2968.680087] usb 7-2: new full-speed USB device number 4 using uhci_hcd [ 2969.092085] usb 7-2: device not accepting address 4, error -71 [ 2969.208155] usb 7-2: new full-speed USB device number 5 using uhci_hcd [ 2969.624076] usb 7-2: device not accepting address 5, error -71 [ 2969.624118] hub 7-0:1.0: unable to enumerate USB device on port 2 [ 4520.240340] usb 7-1: new full-speed USB device number 6 using uhci_hcd [ 4520.364079] usb 7-1: device descriptor read/64, error -71 [ 4520.588109] usb 7-1: device descriptor read/64, error -71 [ 4520.804140] usb 7-1: new full-speed USB device number 7 using uhci_hcd [ 4520.924136] usb 7-1: device descriptor read/64, error -71 [ 4521.148083] usb 7-1: device descriptor read/64, error -71 [ 4521.364105] usb 7-1: new full-speed USB device number 8 using uhci_hcd [ 4521.776237] usb 7-1: device not accepting address 8, error -71 [ 4521.888206] usb 7-1: new full-speed USB device number 9 using uhci_hcd [ 4522.296102] usb 7-1: device not accepting address 9, error -71 [ 4522.296150] hub 7-0:1.0: unable to enumerate USB device on port 1 [ 4749.036104] usb 7-2: new full-speed USB device number 10 using uhci_hcd [ 4749.156209] usb 7-2: device descriptor read/64, error -71 [ 4749.380215] usb 7-2: device descriptor read/64, error -71 [ 4749.596206] usb 7-2: new full-speed USB device number 11 using uhci_hcd [ 4749.716409] usb 7-2: device descriptor read/64, error -71 [ 4749.940110] usb 7-2: device descriptor read/64, error -71 [ 4750.156257] usb 7-2: new full-speed USB device number 12 using uhci_hcd [ 4750.572150] usb 7-2: device not accepting address 12, error -71 [ 4750.684215] usb 7-2: new full-speed USB device number 13 using uhci_hcd [ 4751.100182] usb 7-2: device not accepting address 13, error -71 [ 4751.100224] hub 7-0:1.0: unable to enumerate USB device on port 2 Here is my system: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 08ff:2810 AuthenTec, Inc. AES2810 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 2 port SATA Controller [IDE mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 00:1f.5 IDE interface: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 2 port SATA Controller [IDE mode] (rev 02) 02:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba) 02:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04) 02:01.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21) 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Does anyone have any clue what would be the problem?

    Read the article

  • USB mouse does not work on boot

    - by Uku Loskit
    My problem is pretty much a duplicate of the one described in USB mouse late to load , but the solution there has not worked for me. I'm running the same OS and experiencing the exact same issue. It disappears after 10 seconds or so. Booting with the options specified in the other question did not fix it :/ Thanks in advance. sheepz@sheepz-desktop:~$ dmesg | egrep "hci|usb" [ 0.188000] usbcore: registered new interface driver usbfs [ 0.188000] usbcore: registered new interface driver hub [ 0.188000] usbcore: registered new device driver usb [ 0.358613] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.358627] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.358637] uhci_hcd: USB Universal Host Controller Interface driver [ 0.358683] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.358691] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.358695] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.358726] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 0.358758] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e100 [ 0.358927] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.358932] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.358935] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.358964] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 0.358991] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e200 [ 0.359132] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.359137] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.359139] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.359165] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 0.359193] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e300 [ 0.359327] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 [ 0.359332] uhci_hcd 0000:00:1d.3: setting latency timer to 64 [ 0.359334] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 0.359360] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 0.359387] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e400 [ 0.731933] usb 1-1: new full speed USB device using uhci_hcd and address 2 [ 1.023859] usb 1-2: new full speed USB device using uhci_hcd and address 3 [ 16.136175] usb 1-2: device descriptor read/64, error -110 [ 31.352481] usb 1-2: device descriptor read/64, error -110 [ 31.568485] usb 1-2: new full speed USB device using uhci_hcd and address 4 [ 46.680794] usb 1-2: device descriptor read/64, error -110 [ 61.903555] usb 1-2: device descriptor read/64, error -110 [ 62.119671] usb 1-2: new full speed USB device using uhci_hcd and address 5 [ 72.541078] usb 1-2: device not accepting address 5, error -110 [ 72.653194] usb 1-2: new full speed USB device using uhci_hcd and address 6 [ 83.066637] usb 1-2: device not accepting address 6, error -110 [ 83.178615] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 83.562546] usbcore: registered new interface driver hiddev [ 83.578827] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb3/3-1/3-1:1.0/input/input3 [ 83.579016] generic-usb 0003:046D:C01D.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-1/input0 [ 83.579244] usbcore: registered new interface driver usbhid [ 83.579246] usbhid: USB HID core driver [114025.224407] usb 3-1: USB disconnect, address 2 sheepz@sheepz-desktop:~$ dmesg | egrep "hci|usb" [ 0.188000] usbcore: registered new interface driver usbfs [ 0.188000] usbcore: registered new interface driver hub [ 0.188000] usbcore: registered new device driver usb [ 0.358613] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.358627] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.358637] uhci_hcd: USB Universal Host Controller Interface driver [ 0.358683] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.358691] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.358695] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.358726] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 0.358758] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e100 [ 0.358927] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.358932] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.358935] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.358964] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 0.358991] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e200 [ 0.359132] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.359137] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.359139] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.359165] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 0.359193] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e300 [ 0.359327] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 [ 0.359332] uhci_hcd 0000:00:1d.3: setting latency timer to 64 [ 0.359334] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 0.359360] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 0.359387] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e400 [ 0.731933] usb 1-1: new full speed USB device using uhci_hcd and address 2 [ 1.023859] usb 1-2: new full speed USB device using uhci_hcd and address 3 [ 16.136175] usb 1-2: device descriptor read/64, error -110 [ 31.352481] usb 1-2: device descriptor read/64, error -110 [ 31.568485] usb 1-2: new full speed USB device using uhci_hcd and address 4 [ 46.680794] usb 1-2: device descriptor read/64, error -110 [ 61.903555] usb 1-2: device descriptor read/64, error -110 [ 62.119671] usb 1-2: new full speed USB device using uhci_hcd and address 5 [ 72.541078] usb 1-2: device not accepting address 5, error -110 [ 72.653194] usb 1-2: new full speed USB device using uhci_hcd and address 6 [ 83.066637] usb 1-2: device not accepting address 6, error -110 [ 83.178615] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 83.562546] usbcore: registered new interface driver hiddev [ 83.578827] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb3/3-1/3-1:1.0/input/input3 [ 83.579016] generic-usb 0003:046D:C01D.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-1/input0 [ 83.579244] usbcore: registered new interface driver usbhid [ 83.579246] usbhid: USB HID core driver

    Read the article

  • Getting USB Wifi device to work

    - by Lolwhites
    I have been trying to get an Olitec Wifi N USB dongle to work. At first it lit up but wouldn't connect. A little Googling suggested that it would need ndiswrapper to make it work. After installing and trying to add driver with ndisgtk, I got the error message FATAL: Module ndiswrapper not found., but the driver appears in the list of currently installed ones anyway. However, the situation appears even worse: The USB device doesn't even light up (which it does when plugged into my netbook), suggesting the thing isn't detected any more. How to I go about resolving this issue? I've tried uninstalling ndiswrapper but there seems to have been some permanent change as the device is still not lighting up, as it did at first. Edit: Contents of /etc/modprobe.d/ndiswrapper.conf alias usb:v04F2pAFF7d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v04F2pAFF8d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v04F2pAFF9d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v04F2pAFFAd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v04F2pAFFBd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v04F2pAFFCd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v050Dp1102d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v050Dp2102d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v050Dp2103d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0586p341Fd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v06F8pE033d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v07AAp0056d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v07B8p8178d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v07B8p8189d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0B05p17ABd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8170d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8176d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8177d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8178d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp817Ad*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp817Bd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp817Cd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp817Ed*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp817Fd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8186d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8192d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BFFp8160d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0DF6p0052d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0DF6p005Cd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0DF6p0061d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0EB0p9071d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v103Cp1629d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v13D3p3357d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v13D3p3358d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v13D3p3359d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2001p3307d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2001p3308d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2001p3309d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2001p330Ad*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019p1201d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019p4902d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019p4903d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019p4904d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019pAB2Ad*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019pAB2Bd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019pAB2Cd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019pAB2Ed*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019pED17d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v20F4p624Dd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v20F4p648Bd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v20F4p664Bd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v4855p0090d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v4855p0091d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v4856p0091d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v7392p7811d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v7392p7822d*dc*dsc*dp*ic*isc*ip* ndiswrapper

    Read the article

  • Cannot mount USB 3 harddrive

    - by Thijs
    I cannot mount an USB 3 harddrive. When looking at dmesg I got the following error: [ 96.463269] usb 3-2.1: >new low-speed USB device number 10 using xhci_hcd [ 96.485777] usb 3-2.1: >New USB device found, idVendor=046d, idProduct=c025 [ 96.485787] usb 3-2.1: >New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 96.485792] usb 3-2.1: >Product: USB-PS/2 Optical Mouse [ 96.485797] usb 3-2.1: >Manufacturer: B16_b_02 [ 96.486118] usb 3-2.1: >ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes [ 96.490149] input: B16_b_02 USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2.1/3-2.1:1.0/input/input12 [ 96.490500] hid-generic 0003:046D:C025.0003: >input,hidraw0: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:14.0-2.1/input0 [ 114.088984] usb 3-2.3: >new high-speed USB device number 11 using xhci_hcd [ 114.105041] usb 3-2.3: >New USB device found, idVendor=13fd, idProduct=1618 [ 114.105051] usb 3-2.3: >New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 257.531777] usb 3-2.3: >USB disconnect, device number 11 [ 258.513912] usb 3-2.4: >new high-speed USB device number 12 using xhci_hcd [ 258.514046] usb 3-2.4: >Device not responding to set address. [ 258.717649] usb 3-2.4: >Device not responding to set address. [ 258.921203] usb 3-2.4: >device not accepting address 12, error -71 [ 258.937388] hub 3-2:1.0: >unable to enumerate USB device on port 4 I have tried to mount the drive on ubuntu-12.04 and it mounts just fine.

    Read the article

  • Self-powered USB hub and power supply adapter ampere capacity

    - by galacticninja
    I am looking for a power supply adapter for my USB Hub so it can support at least 2 bus-powered external hard drives. The hub's rating is 5 volts, 2 amperes. I would like to know if it would be OK to buy a power supply adapter rated at less than 2A. I've been looking for power supply adapters and the ones that do support 2A are more expensive (more expensive than the USB hub itself) compared to those that support less than 2A. Will power supply adapter that supports less than 2A (~1-1.5A) work fine to support two external hard drives? The external hard drives are both bus-powered Western Digital My Passport Essentials 250 GB. The OS is Windows XP SP3.

    Read the article

  • USB 3.0 port with USB 3.0 device in Ubuntu 12.10

    - by fernando garcía
    When I try to connect a USB 3.0 device in Ubuntu 12.10 (ASUS K55VD, kernel 3.5.0-19-generic #30-Ubuntu SMP), the system says [ 74.747832] hub 3-0:1.0: unable to enumerate USB device on port 1 [ 74.931957] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd [ 74.949390] usb 4-1: New USB device found, idVendor=05e3, idProduct=0731 [ 74.949396] usb 4-1: New USB device strings: Mfr=0, Product=1, SerialNumber=2 [ 74.949400] usb 4-1: Product: USB Storage [ 74.949403] usb 4-1: SerialNumber: 0000000000000033 [ 75.033327] usbcore: registered new interface driver uas [ 75.038548] Initializing USB Mass Storage driver... [ 75.038651] scsi7 : usb-storage 4-1:1.0 [ 75.038700] usbcore: registered new interface driver usb-storage [ 75.038701] USB Mass Storage support registered. but it does not recognize the device, and the disks applications (gparted, nautilus) act as if nothing had been connected. I have checked other questions, but either they have no answers or they told about previous Ubuntu version with 3.0.x kernels. A USB 2.0 device will work in the USB 3.0 ports. A USB 3.0 device will work (at USB 2.0 speeds) in the USB 2.0 ports. The problem, as I wrote, is between USB 3.0 devices and USB 3.0 ports. I have my USB 3.0 ports configured without legacy support via the BIOS (the way they should be, I suppose). But I also have tried to configure them with XHCI Preboot mode disabled. Have any one solved a similar problem? Thanks in advance.

    Read the article

  • Unable to view USB stick/drive contents

    - by Harshit Sachdeva
    So, I plug-in my USB stick, copy a file from the hard drive to the USB stick, and safely remove the USB stick. I then plug out the USB stick. When I plug the USB stick back into the computer again, the previous contents of the USB stick are all gone. It shows an empty drive. I am using Windows XP SP 2 with an 8 GB USB stick from Transcend.

    Read the article

  • USB Drive Not recognized

    - by user36582
    My Friend's Pen Drive, which was working well very well just few days ago, is not being recognized after getting used by a virus affected machine. Its not on fdisk -l or lsusb However in dmesg I can see the following: [ 977.300013] usb 5-2: new full speed USB device using uhci_hcd and address 2 [ 977.420014] usb 5-2: device descriptor read/64, error -71 [ 977.644023] usb 5-2: device descriptor read/64, error -71 [ 977.860013] usb 5-2: new full speed USB device using uhci_hcd and address 3 [ 977.980013] usb 5-2: device descriptor read/64, error -71 [ 978.204013] usb 5-2: device descriptor read/64, error -71 [ 978.420013] usb 5-2: new full speed USB device using uhci_hcd and address 4 [ 978.828015] usb 5-2: device not accepting address 4, error -71 [ 978.940015] usb 5-2: new full speed USB device using uhci_hcd and address 5 [ 979.348013] usb 5-2: device not accepting address 5, error -71 [ 979.348292] hub 5-0:1.0: unable to enumerate USB device on port 2 [ 1017.848015] usb 5-2: new full speed USB device using uhci_hcd and address 6 [ 1017.968012] usb 5-2: device descriptor read/64, error -71 [ 1018.192017] usb 5-2: device descriptor read/64, error -71 [ 1018.408014] usb 5-2: new full speed USB device using uhci_hcd and address 7 [ 1018.528012] usb 5-2: device descriptor read/64, error -71 [ 1018.752023] usb 5-2: device descriptor read/64, error -71 [ 1018.968012] usb 5-2: new full speed USB device using uhci_hcd and address 8 [ 1019.376019] usb 5-2: device not accepting address 8, error -71 [ 1019.488011] usb 5-2: new full speed USB device using uhci_hcd and address 9 [ 1019.896016] usb 5-2: device not accepting address 9, error -71 [ 1019.896308] hub 5-0:1.0: unable to enumerate USB device on port 2 [ 1049.984016] usb 5-1: new full speed USB device using uhci_hcd and address 10 [ 1050.104014] usb 5-1: device descriptor read/64, error -71 [ 1050.328014] usb 5-1: device descriptor read/64, error -71 [ 1050.544014] usb 5-1: new full speed USB device using uhci_hcd and address 11 [ 1050.664018] usb 5-1: device descriptor read/64, error -71 [ 1050.888019] usb 5-1: device descriptor read/64, error -71 [ 1051.104025] usb 5-1: new full speed USB device using uhci_hcd and address 12 [ 1051.512014] usb 5-1: device not accepting address 12, error -71 [ 1051.624101] usb 5-1: new full speed USB device using uhci_hcd and address 13 [ 1052.032014] usb 5-1: device not accepting address 13, error -71 [ 1052.032991] hub 5-0:1.0: unable to enumerate USB device on port 1 What these Errors actually mean and how Can I get this pen drive Back to work ??

    Read the article

  • The Best Free Tools for Creating a Bootable Windows or Linux USB Drive

    - by Lori Kaufman
    If you need to install Windows or Linux and you don’t have access to a CD/DVD drive, a bootable USB drive is the solution. You can boot to the USB drive, using it to run the OS setup program, just like a CD or DVD. We have collected some links to free programs that allow you to easily setup a USB drive to install Windows or Linux on a computer. NOTE: If you have problems getting the BIOS on your computer to let you boot from a USB drive, see our article about booting from a USB drive even if your BIOS won’t let you. What Is the Purpose of the “Do Not Cover This Hole” Hole on Hard Drives? How To Log Into The Desktop, Add a Start Menu, and Disable Hot Corners in Windows 8 HTG Explains: Why You Shouldn’t Use a Task Killer On Android

    Read the article

  • problem with wireless usb keyboard

    - by Sasha
    I have a problem with wireless keyboard. Problem is: On log, kern.log, messages and syslog is only this line. Every second is 50 lines with such message. Oct 1 08:14:12 wwserver kernel: [ 1447.978908] usb 7-1.3: input irq status -75 received Because these messages is disk full. For this I have to delete log files. Please for help. kern.log file: Oct 1 08:13:53 wwserver kernel: [ 1428.820057] usb 7-1: new full speed USB device using uhci_hcd and address 3 Oct 1 08:13:53 wwserver kernel: [ 1428.977383] usb 7-1: configuration #1 chosen from 1 choice Oct 1 08:13:53 wwserver kernel: [ 1428.980919] hub 7-1:1.0: USB hub found Oct 1 08:13:53 wwserver kernel: [ 1428.982288] hub 7-1:1.0: 4 ports detected Oct 1 08:13:53 wwserver kernel: [ 1429.261317] usb 7-1.3: new full speed USB device using uhci_hcd and address 4 Oct 1 08:13:58 wwserver kernel: [ 1434.408160] usb 7-1.3: configuration #1 chosen from 1 choice Oct 1 08:13:59 wwserver kernel: [ 1434.421484] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1.3/7-1.3:1.0/input/input5 Oct 1 08:13:59 wwserver kernel: [ 1434.421585] generic-usb 0003:046D:C52B.0002: input,hidraw1: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.2-1.3/input0 Oct 1 08:13:59 wwserver kernel: [ 1434.433751] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1.3/7-1.3:1.1/input/input6 Oct 1 08:13:59 wwserver kernel: [ 1434.433933] generic-usb 0003:046D:C52B.0003: input,hiddev96,hidraw2: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.2-1.3/input1 Oct 1 08:13:59 wwserver kernel: [ 1434.450210] generic-usb 0003:046D:C52B.0004: hiddev97,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.2-1.3/input2 Oct 1 08:13:59 wwserver kernel: [ 1434.455416] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1.3/7-1.3:1.3/input/input7 Oct 1 08:13:59 wwserver kernel: [ 1434.455545] generic-usb 0003:046D:C52B.0005: input,hidraw4: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.2-1.3/input3 Oct 1 08:14:12 wwserver kernel: [ 1447.964916] usb 7-1.3: input irq status -75 received Oct 1 08:14:12 wwserver kernel: [ 1447.966907] usb 7-1.3: input irq status -75 received Oct 1 08:14:12 wwserver kernel: [ 1447.968906] usb 7-1.3: input irq status -75 received Oct 1 08:14:12 wwserver kernel: [ 1447.970908] usb 7-1.3: input irq status -75 received Oct 1 08:14:12 wwserver kernel: [ 1447.972907] usb 7-1.3: input irq status -75 received Oct 1 08:14:12 wwserver kernel: [ 1447.974907] usb 7-1.3: input irq status -75 received Oct 1 08:14:12 wwserver kernel: [ 1447.976908] usb 7-1.3: input irq status -75 received Oct 1 08:14:12 wwserver kernel: [ 1447.978908] usb 7-1.3: input irq status -75 received

    Read the article

  • Does not recognize usb sticks and drives

    - by Peter
    When connecting any usb stick to my thinkpad ubuntu 10.10 does not recognize them. I don't see anything on the desktop. the output of "dmesg | tail -n10" gives me: [ 1965.696388] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1965.884537] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.072503] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.260349] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.506227] usb 1-1: new high speed USB device using ehci_hcd and address 9 [ 1966.572375] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.760379] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.948358] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1967.136335] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1967.325423] hub 1-0:1.0: unable to enumerate USB device on port 1 When connecting my usb scanner to the same port: [ 2008.480135] usb 1-1: new high speed USB device using ehci_hcd and address 65 [ 2008.548389] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2008.736786] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2008.924379] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.112348] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.300443] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.488536] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.732180] usb 1-1: new high speed USB device using ehci_hcd and address 71 [ 2014.796299] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2018.000128] usb 2-1: new full speed USB device using uhci_hcd and address 3 And ubuntu 10.10 recognizes that scanner. So: What can i do to see my usb stick? BTW: on my other Thinkpad running fedora 14 it works perfectly... Cheers -Peter

    Read the article

  • ubuntu 10.10 does not recognize usb sticks and drives

    - by Peter
    When connecting any usb stick to my thinkpad ubuntu 10.10 does not recognize them. I don't see anything on the desktop. the output of "dmesg | tail -n10" gives me: [ 1965.696388] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1965.884537] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.072503] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.260349] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.506227] usb 1-1: new high speed USB device using ehci_hcd and address 9 [ 1966.572375] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.760379] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.948358] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1967.136335] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1967.325423] hub 1-0:1.0: unable to enumerate USB device on port 1 When connecting my usb scanner to the same port: [ 2008.480135] usb 1-1: new high speed USB device using ehci_hcd and address 65 [ 2008.548389] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2008.736786] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2008.924379] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.112348] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.300443] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.488536] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.732180] usb 1-1: new high speed USB device using ehci_hcd and address 71 [ 2014.796299] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2018.000128] usb 2-1: new full speed USB device using uhci_hcd and address 3 And ubuntu 10.10 recognizes that scanner. So: What can i do to see my usb stick? BTW: on my other Thinkpad running fedora 14 it works perfectly... Cheers -Peter

    Read the article

  • Problems with making a bootable USB Drive on a Mac

    - by Jason
    I am following this http://www.ubuntu.com/download/help/create-a-usb-stick-on-mac-osx to create a Bootable USB Drive for me Mac and this is the output I get on step 8. new-host:~ Jason$ sudo dd if=/Users/Jason/Desktop/ubuntu-12.04-desktop-amd64.dmg of=/dev/rdisk1s2 bs=1m dd: /dev/rdisk1s2: Invalid argument 691+1 records in 691+0 records out 724566016 bytes transferred in 164.544659 secs (4403461 bytes/sec) What should I do?

    Read the article

  • Universal Pen Drive Linux Will Not Burn IOS Ubuntu 13.10 To USB [duplicate]

    - by Nick
    This question already has an answer here: How to create a bootable USB stick? 4 answers Universal Pen Drive Linux will not let me burn the iso to my usb. Whenever I attempt it it says 'can not open file 'E:*where I put my downloads*\ubuntu-13.10-desktop-amd64.iso' as archive'. Any help please. I just want to move to ubuntu and hopefully never have to use windows again :D Please help me and walk me through this process.

    Read the article

  • Force usb to use same device id, instead of new one

    - by m s kumar
    I am having some trouble in automating the task. I am testing some android based mobiles in linux machine. The automation script uses the device id under "/dev/bus/usb/001/"053" it will be always under bus 001 only.. But the dev is will be random like if i insert one mobile then the dev id will be 053, if remove and insert it again then the dev id will be 054.. The problem is, when some tests runs on the device and if device gets rebooted then new dev id is showing for the rebooted one and my scripts failing due to new dev id.. Is there any way to force usb devices to use same dev id instead of new one. So that there will be no issues to my tests even after device reboots. Thanks in advance.

    Read the article

  • External usb 3.0 hard drive is not recognised when plugged into usb 3 port (ubuntu natty 64 bit).

    - by kimangroo
    I have an Iomega Prestige Portable External Hard Drive 1TB USB 3.0. It works fine on windows 7 as a usb 3.0 drive. It isn't detected on ubuntu natty 64bit, 2.6.38-8-generic. fdisk -l cannot see it at all: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1bed746b Device Boot Start End Blocks Id System /dev/sda1 1 1689 13560832 27 Unknown /dev/sda2 * 1689 1702 102400 7 HPFS/NTFS /dev/sda3 1702 19978 146805760 7 HPFS/NTFS /dev/sda4 19978 60802 327914497 5 Extended /dev/sda5 25555 60802 283120640 7 HPFS/NTFS /dev/sda6 19978 23909 31571968 83 Linux /dev/sda7 23909 25555 13218816 82 Linux swap / Solaris Partition table entries are not in disk order lsusb can see it: Bus 003 Device 003: ID 059b:0070 Iomega Corp. Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 004: ID 05fe:0011 Chic Technology Corp. Browser Mouse Bus 002 Device 003: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 005: ID 0489:e00f Foxconn / Hon Hai Bus 001 Device 004: ID 0c45:64b5 Microdia Bus 001 Device 003: ID 08ff:168f AuthenTec, Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub And dmesg | grep -i xhci (I may have unplugged the drive and plugged it back in again after booting): [ 1.659060] pci 0000:04:00.0: xHCI HW did not halt within 2000 usec status = 0x0 [ 11.484971] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 11.484997] xhci_hcd 0000:04:00.0: setting latency timer to 64 [ 11.485002] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 11.485064] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 [ 11.636149] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 [ 11.636241] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X [ 11.636246] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X [ 11.636251] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X [ 11.636256] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X [ 11.636261] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X [ 11.639654] xHCI xhci_add_endpoint called for root hub [ 11.639655] xHCI xhci_check_bandwidth called for root hub [ 11.956366] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 2 [ 12.001073] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.007059] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.012932] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.018922] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.049139] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.056754] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.131607] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 12.179717] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.686876] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 12.687058] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 12.687152] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 43.330737] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 2 [ 43.422579] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 43.422658] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af00 [ 43.422665] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af40 [ 43.422671] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af80 [ 43.422677] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669afc0 [ 43.531159] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 125.160248] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.766466] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 3 [ 903.807789] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.813530] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.819400] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.825104] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.855067] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862314] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862597] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.913211] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 904.424416] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 904.424599] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 904.424700] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 935.139021] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 3 [ 935.226075] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 935.226140] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b00 [ 935.226148] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b40 [ 935.226153] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b80 [ 935.226159] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186bc0 [ 935.343339] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst I thought it might be that the firmware wasn't compatible with linux or something, but when booting a live image of partedmagic, (2.6.38.4-pmagic), the drive was detected fine, I could mount it and got usb 3.0 speeds (at least they double the speeds I got from plugging same drive in usb 2 ports). dmesg in partedmagic did say something about no SuperSpeed endpoint which was an error I saw in a previous dmesg of ubuntu: Jun 27 15:49:02 (none) user.info kernel: [ 2.978743] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Jun 27 15:49:02 (none) user.debug kernel: [ 2.978771] xhci_hcd 0000:04:00.0: setting latency timer to 64 Jun 27 15:49:02 (none) user.info kernel: [ 2.978781] xhci_hcd 0000:04:00.0: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 2.978856] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 Jun 27 15:49:02 (none) user.info kernel: [ 3.089458] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 Jun 27 15:49:02 (none) user.debug kernel: [ 3.089541] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089544] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089546] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089548] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089550] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X Jun 27 15:49:02 (none) user.warn kernel: [ 3.092857] usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values Jun 27 15:49:02 (none) user.info kernel: [ 3.092864] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 Jun 27 15:49:02 (none) user.info kernel: [ 3.092866] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Jun 27 15:49:02 (none) user.info kernel: [ 3.092867] usb usb3: Product: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 3.092869] usb usb3: Manufacturer: Linux 2.6.38.4-pmagic xhci_hcd Jun 27 15:49:02 (none) user.info kernel: [ 3.092870] usb usb3: SerialNumber: 0000:04:00.0 Jun 27 15:49:02 (none) user.debug kernel: [ 3.092961] xHCI xhci_add_endpoint called for root hub Jun 27 15:49:02 (none) user.debug kernel: [ 3.092963] xHCI xhci_check_bandwidth called for root hub Well I have no idea what's going wrong, and I haven't had much luck from google and the forums so far. A number of unanswered threads with people with similar error messages and problems only. Hopefully someone here can help or point me in the right direction?!

    Read the article

  • External USB drive is failing

    - by dma_k
    I have an external USB 2.0 drive WD My Book Mirror Edition, running in RAID 1 (mirroring) mode. A while ago the hard drive started to fail: it stops responding (directories are not listed returning an error after a big timeout). Sometimes it works for weeks before a failure, sometimes – few hours. Small write operations (like removing few files or editing a small file) do not harm, but when copying large files to the drive over the network, or creating the archive locally, the kernel dumps. Also interesting to note that once kernel has failed, Linux does not want to reboot normally (reboot hangs); when Linux box is shutdown with power button, WD drive does not go to sleep mode (as it usually does): leds continue to run, pressing and holding the "shutdown" button on drive's back panel does not do anything; only unplugging the power cord helps. Here goes the boot log: Aug 16 00:32:21 kernel: [ 1.514106] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Aug 16 00:32:21 kernel: [ 1.657738] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 1.673747] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 1.673751] ehci_hcd 0000:00:1d.7: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.725224] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Aug 16 00:32:21 kernel: [ 1.741647] ehci_hcd 0000:00:1d.7: using broken periodic workaround Aug 16 00:32:21 kernel: [ 1.761790] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported Aug 16 00:32:21 kernel: [ 1.761873] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdfff000 Aug 16 00:32:21 kernel: [ 1.796043] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 Aug 16 00:32:21 kernel: [ 1.879069] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Aug 16 00:32:21 kernel: [ 1.895446] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 1.911796] usb usb1: Product: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.928015] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd Aug 16 00:32:21 kernel: [ 1.944331] usb usb1: SerialNumber: 0000:00:1d.7 Aug 16 00:32:21 kernel: [ 1.961285] usb usb1: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 1.994412] hub 1-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.010864] hub 1-0:1.0: 8 ports detected Aug 16 00:32:21 kernel: [ 2.085939] uhci_hcd: USB Universal Host Controller Interface driver Aug 16 00:32:21 kernel: [ 2.191945] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 2.226029] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.226034] uhci_hcd 0000:00:1d.0: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.243237] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 Aug 16 00:32:21 kernel: [ 2.260390] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fe00 Aug 16 00:32:21 kernel: [ 2.277517] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.294815] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.312173] usb usb2: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.329534] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.346828] usb usb2: SerialNumber: 0000:00:1d.0 Aug 16 00:32:21 kernel: [ 2.412989] usb usb2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.430651] usb 1-2: new high speed USB device using ehci_hcd and address 2 Aug 16 00:32:21 kernel: [ 2.449046] hub 2-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.466514] hub 2-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.484639] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Aug 16 00:32:21 kernel: [ 2.537750] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.537756] uhci_hcd 0000:00:1d.1: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.555085] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 Aug 16 00:32:21 kernel: [ 2.572231] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fd00 Aug 16 00:32:21 kernel: [ 2.589593] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.606869] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.624134] usb usb3: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.641329] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.658505] usb usb3: SerialNumber: 0000:00:1d.1 Aug 16 00:32:21 kernel: [ 2.675843] usb usb3: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.692864] hub 3-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.709651] hub 3-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.727378] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Aug 16 00:32:21 kernel: [ 2.768252] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.768258] uhci_hcd 0000:00:1d.2: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.806679] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 Aug 16 00:32:21 kernel: [ 2.824117] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fc00 Aug 16 00:32:21 kernel: [ 2.841405] usb 1-2: New USB device found, idVendor=1058, idProduct=1104 Aug 16 00:32:21 kernel: [ 2.858448] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Aug 16 00:32:21 kernel: [ 2.875347] usb 1-2: Product: My Book Aug 16 00:32:21 kernel: [ 2.892113] usb 1-2: Manufacturer: Western Digital Aug 16 00:32:21 kernel: [ 2.908915] usb 1-2: SerialNumber: 575532553130303530353538 Aug 16 00:32:21 kernel: [ 2.943242] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.960405] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.977615] usb usb4: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.994687] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.011711] usb usb4: SerialNumber: 0000:00:1d.2 Aug 16 00:32:21 kernel: [ 3.029589] usb usb4: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.082027] sd 2:0:0:0: [sda] Attached SCSI disk Aug 16 00:32:21 kernel: [ 3.103953] usb 1-2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.122625] hub 4-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.140484] hub 4-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.161680] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 Aug 16 00:32:21 kernel: [ 3.181257] uhci_hcd 0000:00:1d.3: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 3.181263] uhci_hcd 0000:00:1d.3: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.198614] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 Aug 16 00:32:21 kernel: [ 3.216012] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fb00 Aug 16 00:32:21 kernel: [ 3.249877] Uniform CD-ROM driver Revision: 3.20 Aug 16 00:32:21 kernel: [ 3.267765] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 3.284947] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 3.302023] usb usb5: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.319215] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.336298] usb usb5: SerialNumber: 0000:00:1d.3 Aug 16 00:32:21 kernel: [ 3.368377] Initializing USB Mass Storage driver... Aug 16 00:32:21 kernel: [ 3.390652] usbcore: registered new interface driver hiddev Aug 16 00:32:21 kernel: [ 3.408109] scsi4 : SCSI emulation for USB Mass Storage devices Aug 16 00:32:21 kernel: [ 3.425281] sr 0:0:1:0: Attached scsi CD-ROM sr0 Aug 16 00:32:21 kernel: [ 3.438978] sr 0:0:1:0: Attached scsi generic sg0 type 5 Aug 16 00:32:21 kernel: [ 3.456328] usbcore: registered new interface driver usb-storage Aug 16 00:32:21 kernel: [ 3.474564] usb-storage: device found at 2 Aug 16 00:32:21 kernel: [ 3.474567] usb-storage: waiting for device to settle before scanning Aug 16 00:32:21 kernel: [ 3.475320] sd 2:0:0:0: Attached scsi generic sg1 type 0 Aug 16 00:32:21 kernel: [ 3.492587] USB Mass Storage support registered. Aug 16 00:32:21 kernel: [ 3.510930] usb usb5: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.531076] hub 5-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.548399] hub 5-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.591743] input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.1/input/input2 Aug 16 00:32:21 kernel: [ 3.609515] generic-usb 0003:1058:1104.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-2/input1 Aug 16 00:32:21 kernel: [ 3.627466] usbcore: registered new interface driver usbhid Aug 16 00:32:21 kernel: [ 8.581664] usb-storage: device scan complete Aug 16 00:32:21 kernel: [ 8.624270] scsi 4:0:0:0: Direct-Access WD My Book 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.655135] scsi 4:0:0:1: Enclosure WD My Book Device 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.675393] sd 4:0:0:0: Attached scsi generic sg2 type 0 Aug 16 00:32:21 kernel: [ 8.698669] scsi 4:0:0:1: Attached scsi generic sg3 type 13 Aug 16 00:32:21 kernel: [ 8.723370] sd 4:0:0:0: [sdb] 1953513472 512-byte logical blocks: (1.00 TB/931 GiB) Aug 16 00:32:21 kernel: [ 8.750477] sd 4:0:0:0: [sdb] Write Protect is off Aug 16 00:32:21 kernel: [ 8.769411] sd 4:0:0:0: [sdb] Mode Sense: 10 00 00 00 Aug 16 00:32:21 kernel: [ 8.769414] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.822971] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.841978] sdb: sdb1 Aug 16 00:32:21 kernel: [ 8.905580] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.924173] sd 4:0:0:0: [sdb] Attached SCSI disk Aug 16 00:32:21 kernel: [ 11.600492] XFS mounting filesystem sdb1 Aug 16 00:32:21 kernel: [ 12.222948] Ending clean XFS mount for filesystem: sdb1 After a while the following appears in a log: Aug 16 09:30:56 kernel: [32359.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:31:59 kernel: [32422.112035] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:33:00 kernel: [32483.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 And then it is followed by few kernel dumps, which I think, are not good: Aug 16 09:33:40 kernel: [32520.428027] INFO: task xfssyncd:1002 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32520.462689] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32520.497422] xfssyncd D c3d84a60 0 1002 2 0x00000000 Aug 16 09:33:40 kernel: [32520.532117] f6c9aa80 00000046 c1132742 c3d84a60 00000286 c1418100 c1418100 00000000 Aug 16 09:33:40 kernel: [32520.566867] f6c9ac3c c2808100 00000000 f653b18b 00001d76 00000001 f6c9aa80 c3c3f0e0 Aug 16 09:33:40 kernel: [32520.601343] 08e59242 f6c9ac3c 2e41392b 00000000 08e59242 00000000 c3f7fb48 0067385a Aug 16 09:33:40 kernel: [32520.635533] Call Trace: Aug 16 09:33:40 kernel: [32520.668991] [<c1132742>] ? cfq_set_request+0x0/0x290 Aug 16 09:33:40 kernel: [32520.702804] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32520.736555] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32520.770360] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32520.804110] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32520.837713] [<c1128230>] ? blk_peek_request+0x135/0x143 Aug 16 09:33:40 kernel: [32520.871265] [<f8582987>] ? scsi_dispatch_cmd+0x185/0x1e5 [scsi_mod] Aug 16 09:33:40 kernel: [32520.904407] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32520.937007] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32520.969033] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.000485] [<c10cffd1>] ? bio_add_page+0x28/0x2e Aug 16 09:33:40 kernel: [32521.031403] [<f8918d38>] ? _xfs_buf_ioapply+0x206/0x22b [xfs] Aug 16 09:33:40 kernel: [32521.061888] [<f89197bd>] ? xfs_buf_iorequest+0x38/0x60 [xfs] Aug 16 09:33:40 kernel: [32521.091845] [<f8907230>] ? xlog_bdstrat_cb+0x16/0x3d [xfs] Aug 16 09:33:40 kernel: [32521.121222] [<f8905781>] ? XFS_bwrite+0x32/0x64 [xfs] Aug 16 09:33:40 kernel: [32521.150007] [<f89059be>] ? xlog_sync+0x20b/0x311 [xfs] Aug 16 09:33:40 kernel: [32521.178214] [<f89112fc>] ? xfs_trans_ail_tail+0x12/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.205914] [<f8906261>] ? xlog_state_sync_all+0xa2/0x141 [xfs] Aug 16 09:33:40 kernel: [32521.233074] [<f8906611>] ? _xfs_log_force+0x51/0x68 [xfs] Aug 16 09:33:40 kernel: [32521.259664] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32521.285662] [<f8906636>] ? xfs_log_force+0xe/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.311171] [<f89202df>] ? xfs_sync_worker+0x17/0x5c [xfs] Aug 16 09:33:40 kernel: [32521.336117] [<f891fbb7>] ? xfssyncd+0x134/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.360498] [<f891fa83>] ? xfssyncd+0x0/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.384211] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32521.407890] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32521.430876] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32521.453394] INFO: task flush-8:16:12945 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32521.476116] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32521.498579] flush-8:16 D 00000000 0 12945 2 0x00000000 Aug 16 09:33:40 kernel: [32521.520649] f4e4d540 00000046 e412e940 00000000 00000002 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32521.542426] f4e4d6fc c2808100 00000000 00000000 000008b4 00000001 f4e4d540 c3c3f0e0 Aug 16 09:33:40 kernel: [32521.563745] 02e905a8 f4e4d6fc 007a5399 00000000 02e905a8 00000000 f4e2db48 00670b98 Aug 16 09:33:40 kernel: [32521.585077] Call Trace: Aug 16 09:33:40 kernel: [32521.605790] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32521.626184] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32521.646133] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32521.665659] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32521.684716] [<f891796e>] ? xfs_convert_page+0x30a/0x331 [xfs] Aug 16 09:33:40 kernel: [32521.703366] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32521.721644] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32521.739465] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.756896] [<c10cfa45>] ? bio_alloc_bioset+0x7b/0xba Aug 16 09:33:40 kernel: [32521.774046] [<f8917af0>] ? xfs_submit_ioend_bio+0x3b/0x44 [xfs] Aug 16 09:33:40 kernel: [32521.790694] [<f8917ba3>] ? xfs_submit_ioend+0xaa/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.806736] [<f891817d>] ? xfs_page_state_convert+0x5c0/0x61c [xfs] Aug 16 09:33:40 kernel: [32521.822859] [<c113705b>] ? __lookup_tag+0x8e/0xee Aug 16 09:33:40 kernel: [32521.838958] [<f891840d>] ? xfs_vm_writepage+0x91/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.855039] [<c108bbcc>] ? __writepage+0x8/0x22 Aug 16 09:33:40 kernel: [32521.871067] [<c108c17b>] ? write_cache_pages+0x1af/0x29f Aug 16 09:33:40 kernel: [32521.886616] [<c108bbc4>] ? __writepage+0x0/0x22 Aug 16 09:33:40 kernel: [32521.901593] [<c108c285>] ? generic_writepages+0x1a/0x21 Aug 16 09:33:40 kernel: [32521.916455] [<f8918338>] ? xfs_vm_writepages+0x0/0x38 [xfs] Aug 16 09:33:40 kernel: [32521.931484] [<c108c2a5>] ? do_writepages+0x19/0x25 Aug 16 09:33:40 kernel: [32521.946648] [<c10c80d9>] ? writeback_single_inode+0xc7/0x273 Aug 16 09:33:40 kernel: [32521.961675] [<c10c8c44>] ? writeback_inodes_wb+0x3dd/0x49c Aug 16 09:33:40 kernel: [32521.976831] [<c10c8e18>] ? wb_writeback+0x115/0x178 Aug 16 09:33:40 kernel: [32521.991778] [<c10c901f>] ? wb_do_writeback+0x121/0x131 Aug 16 09:33:40 kernel: [32522.006538] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32522.021091] [<c10c9050>] ? bdi_writeback_task+0x21/0x89 Aug 16 09:33:40 kernel: [32522.035493] [<c10979e5>] ? bdi_start_fn+0x59/0xa4 Aug 16 09:33:40 kernel: [32522.049765] [<c109798c>] ? bdi_start_fn+0x0/0xa4 Aug 16 09:33:40 kernel: [32522.063792] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32522.077612] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32522.091260] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32522.104966] INFO: task smartctl:13098 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32522.118883] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32522.133012] smartctl D 00000020 0 13098 13097 0x00000000 Aug 16 09:33:40 kernel: [32522.147221] e50b9540 00000086 c11d28a8 00000020 00000770 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32522.161720] e50b96fc c2808100 00000000 e53e8800 00000000 00000020 c3cec000 c13886c0 Aug 16 09:33:40 kernel: [32522.176217] f99dab68 e50b96fc 007a4f1e 00000001 c4082f24 c4082ed8 00000001 c3c3f0e0 Aug 16 09:33:40 kernel: [32522.190737] Call Trace: Aug 16 09:33:40 kernel: [32522.205038] [<c11d28a8>] ? __netdev_alloc_skb+0x14/0x2d Aug 16 09:33:40 kernel: [32522.219605] [<c126b799>] ? schedule_timeout+0x20/0xb0 Aug 16 09:33:40 kernel: [32522.234144] [<c112820d>] ? blk_peek_request+0x112/0x143 Aug 16 09:33:40 kernel: [32522.248649] [<f85873b6>] ? scsi_request_fn+0x3c1/0x47a [scsi_mod] Aug 16 09:33:40 kernel: [32522.263233] [<c103aba8>] ? del_timer+0x55/0x5c Aug 16 09:33:40 kernel: [32522.277773] [<c126b6a2>] ? wait_for_common+0xa4/0x100 Aug 16 09:33:40 kernel: [32522.292342] [<c102cd8d>] ? default_wake_function+0x0/0x8 Aug 16 09:33:40 kernel: [32522.306958] [<c112b3d1>] ? blk_execute_rq+0x8b/0xb2 Aug 16 09:33:40 kernel: [32522.321569] [<c112b2ac>] ? blk_end_sync_rq+0x0/0x23 Aug 16 09:33:40 kernel: [32522.336070] [<c112b58b>] ? blk_recount_segments+0x13/0x20 Aug 16 09:33:40 kernel: [32522.350583] [<c1127307>] ? blk_rq_bio_prep+0x44/0x74 Aug 16 09:33:40 kernel: [32522.365059] [<c112b0b2>] ? blk_rq_map_kern+0xc5/0xee Aug 16 09:33:40 kernel: [32522.379439] [<c112e2a5>] ? sg_scsi_ioctl+0x221/0x2aa Aug 16 09:33:40 kernel: [32522.393801] [<c112e672>] ? scsi_cmd_ioctl+0x344/0x39a Aug 16 09:33:40 kernel: [32522.408140] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.422566] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.436832] [<f87676aa>] ? sd_ioctl+0x90/0xb5 [sd_mod] Aug 16 09:33:40 kernel: [32522.451228] [<c112c35f>] ? __blkdev_driver_ioctl+0x53/0x63 Aug 16 09:33:40 kernel: [32522.465689] [<c112cbbf>] ? blkdev_ioctl+0x850/0x891 Aug 16 09:33:40 kernel: [32522.479982] [<c1020474>] ? __wake_up_common+0x34/0x59 Aug 16 09:33:40 kernel: [32522.494138] [<c10244cd>] ? complete+0x28/0x36 Aug 16 09:33:40 kernel: [32522.507986] [<c1086c64>] ? find_get_page+0x1f/0x81 Aug 16 09:33:40 kernel: [32522.521671] [<c10abed5>] ? add_partial+0xe/0x40 Aug 16 09:33:40 kernel: [32522.535285] [<c1086e68>] ? lock_page+0x8/0x1d Aug 16 09:33:40 kernel: [32522.548797] [<c1087432>] ? filemap_fault+0xb5/0x2e6 Aug 16 09:33:40 kernel: [32522.562141] [<c109941c>] ? __do_fault+0x381/0x3b1 Aug 16 09:33:40 kernel: [32522.575441] [<c10d0c30>] ? block_ioctl+0x27/0x2c Aug 16 09:33:40 kernel: [32522.588708] [<c10d0c09>] ? block_ioctl+0x0/0x2c Aug 16 09:33:40 kernel: [32522.601858] [<c10bcd78>] ? vfs_ioctl+0x1c/0x5f Aug 16 09:33:40 kernel: [32522.614917] [<c10bd30c>] ? do_vfs_ioctl+0x4aa/0x4e5 Aug 16 09:33:40 kernel: [32522.627961] [<c10350db>] ? __do_softirq+0x115/0x151 Aug 16 09:33:40 kernel: [32522.640901] [<c126e270>] ? do_page_fault+0x2f1/0x307 Aug 16 09:33:40 kernel: [32522.653803] [<c10bd388>] ? sys_ioctl+0x41/0x58 Aug 16 09:33:40 kernel: [32522.666674] [<c10030fb>] ? sysenter_do_call+0x12/0x28 Then again few messages reset high speed USB device using ehci_hcd and address 2. I have browsed and read similar error reports here and there and I tried: I have upgraded the kernel from v2.6.26-2 to 2.6.32-5, which has not solved the problem. They say, this might a cable problem. I have tried to replace the USB-to-miniUSB cable (that connects external drive with computer) with another one. No changes. Somebody suggests to try another USB port. I have only 4 external USB ports, tried another one with no success. They say to try uhci_hcd. I have unmounted the device, unloaded ehci_hcd and mounted again. The difference was that now in log I get reset full speed USB device using uhci_hcd and address 2 and similar kernel dumps after a while. They say to echo 128 > /sys/block/sdb/device/max_sectors. I tried it with ehci_hcd with no success (note: I have issued this command after the drive was mounted but before using it actively). I have lauched smartmond and checking periodically the output of smartctl: drive temperature is OK, number of bad sectors and uncorrectable errors is 0. Nothing suspicious is reported by S.M.A.R.T. except maybe the following: Aug 16 12:40:12 kernel: [43715.314566] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Aug 16 12:40:13 kernel: [43715.705622] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Of course, I have not tried all combinations of above. But unfortunately, I am run out of cardinal ideas. If anybody can advice something specific about the problem, you are very welcome.

    Read the article

  • front usb wont mount harddrives, internal usb ports do

    - by Thesgsuser
    I have noticed something in my new build, i am using Ubuntu desktop newest version my motherboard is the asus f1a75-m pro R2.0 with the usb ports in the back all my NTFS hard disks or usb sticks work fine, but then.. when i put them in the front usb ports of my chassis (silverstone milo ml-03) they wont mount... I have 2 usb 3.0 ports in front of the case connected with a internal usb 3.0 header. But i verified that the usb 3.0 ports on the back do mount the harddisk so it has nothing to do with usb 3.0 i think. The strange thing is, my mouse works fine on the front usb ports. Every usb hardware piece seems to work except if it has any memory inside it :( What seems to be the problem?

    Read the article

  • composite-video-to-usb adaptor

    - by sawa
    I bought a composite-video-to-usb adaptor. I want to stream video game in ubuntu. How can I do that? My environment: Monoprice USB Video and Audio Grabber Ubuntu 11.04 The relevant output of lsusb: Bus 001 Device 011: ID 0572:262a Conexant Systems (Rockwell), Inc. The relevant output of sudo lshw: *-usb:0 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #4 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:16 ioport:f0e0(size=32) *-usb:1 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #5 vendor: Intel Corporation physical id: 1a.1 bus info: pci@0000:00:1a.1 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:21 ioport:f0c0(size=32) *-usb:2 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #6 vendor: Intel Corporation physical id: 1a.2 bus info: pci@0000:00:1a.2 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:f0a0(size=32) *-usb:3 description: USB Controller product: 82801JI (ICH10 Family) USB2 EHCI Controller #2 vendor: Intel Corporation physical id: 1a.7 bus info: pci@0000:00:1a.7 version: 00 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:18 memory:e0525c00-e0525fff *-multimedia description: Audio device product: 82801JI (ICH10 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:43 memory:e0520000-e0523fff *-usb:4 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:23 ioport:f080(size=32) *-usb:5 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #2 vendor: Intel Corporation physical id: 1d.1 bus info: pci@0000:00:1d.1 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:19 ioport:f060(size=32) *-usb:6 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #3 vendor: Intel Corporation physical id: 1d.2 bus info: pci@0000:00:1d.2 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:f040(size=32) *-usb:7 description: USB Controller product: 82801JI (ICH10 Family) USB2 EHCI Controller #1 vendor: Intel Corporation physical id: 1d.7 bus info: pci@0000:00:1d.7 version: 00 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:e0525800-e0525bff The relevant output of dmesg: [18953.220035] usb 1-1: new high speed USB device using ehci_hcd and address 6 [19964.761076] Linux video capture interface: v2.00 [19964.767112] usbcore: registered new interface driver uvcvideo [19964.767115] USB Video Class driver (v1.0.0)

    Read the article

  • ubuntu 13.04 recognizes usb mobile broadband modem as ethernet connection

    - by Bence Mihalka
    When I plug in my usb mobile broadband modem (ZTE MF-667), in the network manager instead of a mobile broadband connection, I get an ethernet connection, called: Ethernet Network (ZTE WCDMA Technologies MSM), which of course doesn't work. Here is my lsusb output and the relevant parts of dmesg output: lsusb: Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth Bus 001 Device 004: ID 04f2:b1b9 Chicony Electronics Co., Ltd Asus Integrated Webcam Bus 001 Device 005: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 002 Device 004: ID 19d2:1405 ZTE WCDMA Technologies MSM dmesg: [ 195.328467] usb 2-1.1: new high-speed USB device number 3 using ehci-pci [ 195.423545] usb 2-1.1: New USB device found, idVendor=19d2, idProduct=1225 [ 195.423555] usb 2-1.1: New USB device strings: Mfr=3, Product=2, SerialNumber=4 [ 195.423561] usb 2-1.1: Product: ZTE WCDMA Technologies MSM [ 195.423567] usb 2-1.1: Manufacturer: ZTE,Incorporated [ 195.423572] usb 2-1.1: SerialNumber: P680A1ZTED000000 [ 195.426319] scsi7 : usb-storage 2-1.1:1.0 [ 196.425354] scsi 7:0:0:0: CD-ROM CWID USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2 [ 197.447919] usb 2-1.1: USB disconnect, device number 3 [ 197.457582] sr0: scsi3-mmc drive: 243x/186x xa/form2 cdda pop-up [ 197.457594] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 197.459058] sr 7:0:0:0: Attached scsi CD-ROM sr0 [ 197.459483] sr 7:0:0:0: Attached scsi generic sg2 type 5 [ 197.759186] usb 2-1.1: new high-speed USB device number 4 using ehci-pci [ 197.854543] usb 2-1.1: New USB device found, idVendor=19d2, idProduct=1405 [ 197.854556] usb 2-1.1: New USB device strings: Mfr=4, Product=3, SerialNumber=5 [ 197.854564] usb 2-1.1: Product: ZTE WCDMA Technologies MSM [ 197.854572] usb 2-1.1: Manufacturer: ZTE,Incorporated [ 197.854579] usb 2-1.1: SerialNumber: P680A1ZTED010000 [ 197.957739] scsi8 : usb-storage 2-1.1:1.2 [ 198.076554] cdc_ether 2-1.1:1.0 eth1: register 'cdc_ether' at usb-0000:00:1d.0-1.1, CDC Ethernet Device, 00:a0:c6:00:00:00 [ 198.076583] usbcore: registered new interface driver cdc_ether [ 198.955985] scsi 8:0:0:0: CD-ROM CWID USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2 [ 198.956797] scsi 8:0:0:1: Direct-Access ZTE MMC Storage 2.31 PQ: 0 ANSI: 2 I created the appropriate mobile broadband connection manually, but I cannot enable it in network manager, since the device is not recognized as mobile broadband. Any tips how to make it work?

    Read the article

  • Error in installing ZTE AC2738 on ubuntu 3.0.0-12-generic

    - by Netro
    I am getting this error ,struct usb_serial_driver has no member named shutdown. I am installing on 64bit ubuntu 3.0.0-12-generic ... Beginning Verify CD ... ... Verify CD Succeed! ... Beginning Copy Install Package Files ... ... will take a long time, waiting 5 seconds, please ... Copy Install Package Files Succeed! ... 'ztemtApp' previous version not found. and install now Beginning install ... ... Current linux release version is 'Ubuntu' ... Checking 'App' process ... Checking old installation ... Installing ... Current Path is : . : /tmp/ztemt_datacard/Linux 1. Checking Previous Version ... 2. Copying Data Bin ... ... will take a few seconds, please waiting ... /tmp/ztemt_datacard/Linux 3. Auto Load Usb Driver Module ... Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service acpid restart Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the stop(8) and then start(8) utilities, e.g. stop acpid ; start acpid. The restart(8) utility is also available. acpid stop/waiting acpid start/running, process 11802 4. Changing pppd Options ... 5. Changing File Permission ... 6. Deleting Qt lib When Local QT Vertion > V4.4.0 ... ... Package 'libqtgui4' exist ... QT_VERSION = 4 7. Deleting process id file: EVDOApp.pid ... 8. Making USB Serial Driver Module : ztemt.ko ... ... will take a few seconds, please waiting ... make -C /lib/modules/3.0.0-12-generic/build M=/usr/local/bin/ztemtApp/zteusbserial/below2.6.27 modules make[1]: Entering directory `/usr/src/linux-headers-3.0.0-12-generic' CC [M] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.o /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘destroy_serial’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:159:14: error: ‘struct usb_serial_driver’ has no member named ‘shutdown’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:165:18: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_open’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:241:36: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:246:8: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:251:6: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:253:10: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:265:3: warning: passing argument 1 of ‘serial->type->open’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:265:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:265:3: warning: passing argument 2 of ‘serial->type->open’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:265:3: note: expected ‘struct usb_serial_port *’ but argument is of type ‘struct file *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:270:20: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:276:6: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:278:6: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:279:20: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_close’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:355:18: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:357:10: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:358:21: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:371:8: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:372:10: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:375:3: error: too many arguments to function ‘port->serial->type->close’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:377:11: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:378:12: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:379:9: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:380:8: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:386:20: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_write’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:407:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: warning: passing argument 1 of ‘port->serial->type->write’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: warning: passing argument 2 of ‘port->serial->type->write’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: note: expected ‘struct usb_serial_port *’ but argument is of type ‘const unsigned char *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: warning: passing argument 3 of ‘port->serial->type->write’ makes pointer from integer without a cast [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: note: expected ‘const unsigned char *’ but argument is of type ‘int’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: error: too few arguments to function ‘port->serial->type->write’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_write_room’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:429:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:435:2: warning: passing argument 1 of ‘port->serial->type->write_room’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:435:2: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_chars_in_buffer’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:451:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:457:2: warning: passing argument 1 of ‘port->serial->type->chars_in_buffer’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:457:2: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_throttle’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:472:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:479:3: warning: passing argument 1 of ‘port->serial->type->throttle’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:479:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_unthrottle’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:491:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:498:3: warning: passing argument 1 of ‘port->serial->type->unthrottle’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:498:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_ioctl’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:511:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:518:3: warning: passing argument 1 of ‘port->serial->type->ioctl’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:518:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:518:3: warning: passing argument 2 of ‘port->serial->type->ioctl’ makes integer from pointer without a cast [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:518:3: note: expected ‘unsigned int’ but argument is of type ‘struct file *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:518:3: error: too many arguments to function ‘port->serial->type->ioctl’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_set_termios’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:535:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:542:3: warning: passing argument 1 of ‘port->serial->type->set_termios’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:542:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:542:3: warning: passing argument 2 of ‘port->serial->type->set_termios’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:542:3: note: expected ‘struct usb_serial_port *’ but argument is of type ‘struct termios *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:542:3: error: too few arguments to function ‘port->serial->type->set_termios’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_break’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:554:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:561:3: warning: passing argument 1 of ‘port->serial->type->break_ctl’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:561:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_tiocmget’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:629:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:635:3: warning: passing argument 1 of ‘port->serial->type->tiocmget’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:635:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:635:3: error: too many arguments to function ‘port->serial->type->tiocmget’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_tiocmset’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:651:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:657:3: warning: passing argument 1 of ‘port->serial->type->tiocmset’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:657:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:657:3: warning: passing argument 2 of ‘port->serial->type->tiocmset’ makes integer from pointer without a cast [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:657:3: note: expected ‘unsigned int’ but argument is of type ‘struct file *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:657:3: error: too many arguments to function ‘port->serial->type->tiocmset’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘usb_serial_port_work’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:697:12: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘port_release’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:709:2: error: ‘struct device’ has no member named ‘bus_id’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘usb_serial_probe’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:858:2: error: implicit declaration of function ‘lock_kernel’ [-Werror=implicit-function-declaration] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:861:3: error: implicit declaration of function ‘unlock_kernel’ [-Werror=implicit-function-declaration] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1034:3: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1182:23: error: ‘struct device’ has no member named ‘bus_id’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1182:51: error: ‘struct device’ has no member named ‘bus_id’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1183:3: error: ‘struct device’ has no member named ‘bus_id’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘usb_serial_disconnect’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1257:13: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1258:21: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: At top level: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1280:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1280:2: warning: (near initialization for ‘serial_ops.ioctl’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1281:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1281:2: warning: (near initialization for ‘serial_ops.set_termios’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1284:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1284:2: warning: (near initialization for ‘serial_ops.break_ctl’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1286:2: error: unknown field ‘read_proc’ specified in initializer /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1286:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1286:2: warning: (near initialization for ‘serial_ops.ioctl’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1287:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1287:2: warning: (near initialization for ‘serial_ops.tiocmget’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1288:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1288:2: warning: (near initialization for ‘serial_ops.tiocmset’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘usb_serial_init’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1352:2: error: implicit declaration of function ‘info’ [-Werror=implicit-function-declaration] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘fixup_generic’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1406:2: error: ‘struct usb_serial_driver’ has no member named ‘shutdown’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1406:2: error: ‘struct usb_serial_driver’ has no member named ‘shutdown’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1406:1: error: ‘usb_serial_generic_shutdown’ undeclared (first use in this function) /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1406:1: note: each undeclared identifier is reported only once for each function it appears in cc1: some warnings being treated as errors make[2]: *** [/usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.o] Error 1 make[1]: *** [_module_/usr/local/bin/ztemtApp/zteusbserial/below2.6.27] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.0.0-12-generic' make: *** [modules] Error 2 Install finished! Any suggestion? Update: from installation document , In some special cases, the setup package can’t automatically compile the driver, so you need change the configurations yourself and manually compile the driver. Method: enter the directory: /usr/local/bin/ztemtApp/zteusbserial, and find the corresponding kernel version of current system. I can see 2.6.27 2.6.28 2.6.29 2.6.30 2.6.31 2.6.32 2.6.33 2.6.34 2.6.35 2.6.36 2.6.37 2.6.38 2.6.39 below2.6.2 in the directory. Which version shall I pick up for installation? Readme file says, we have to do this to insert ztemt.ko in kernel.

    Read the article

  • External USB attached drive works in Windows XP but not in Windows 7. How to fix?

    - by irrational John
    Earlier this week I purchased this "N52300 EZQuest Pro" external hard drive enclosure from here. I can connect the enclosure using USB 2.0 and access the files in both NTFS partitions on the MBR partitioned drive when I use either Windows XP (SP3) or Mac OS X 10.6. So it works as expected in XP & Snow Leopard. However, the enclosure does not work in Windows 7 (Home Premium) either 64-bit or 32-bit or in Ubuntu 10.04 (kernel 2.6.32-23-generic). I'm thinking this must be a Windows 7 driver problem because the enclosure works in XP & Snow Leopard. I do know that no special drivers are required to use this enclosure. It is supported using the USB mass storage drivers included with XP and OS X. It should also work fine using the mass storage support in Windows 7, no? FWIW, I have also tried using 32-bit Windows 7 on both my desktop, a Gigabyte GA-965P-DS3 with a Pentium Dual-Core E6500 @ 2.93GHz, and on my early 2008 MacBook. I see the same failure in both cases that I see with 64-bit Windows 7. So it doesn't appear to be specific to one hardware platform. I'm hoping someone out there can help me either get the enclosure to work in Windows 7 or convince me that the enclosure hardware is bad and should be RMAed. At the moment though an RMA seems pointless since this appears to be a (Windows 7) device driver problem. I have tried to track down any updates to the mass storage drivers included with Windows 7 but have so far come up empty. Heck, I can't even figure out how to place a bug report with Microsoft since apparently the grace period for Windows 7 email support is only a few months. I came across a link to some USB troubleshooting steps in another question. I haven't had a chance to look over the suggestions on that site or try them yet. Maybe tomorrow if I have time ... ;-) I'll finish up with some more details about the problem. When I connect the enclosure using USB to Windows 7 at first it appears everything worked. Windows detects the drive and installs a driver for it. Looking in Device Manager there is an entry under the Hard Drives section with the title, Hitachi HDT721010SLA360 USB Device. When you open Windows Disk Management the first time after the enclosure has been attached the drive appears as "Not initialize" and I'm prompted to initialize it. This is bogus. After all, the drive worked fine in XP so I know it has already been initialized, partitioned, and formatted. So of course I never try to initialize it "again". (It's a 1 GB drive and I don't want to lose the data on it). Except for this first time, the drive never shows up in Disk Management again unless I uninstall the Hitachi HDT721010SLA360 USB Device entry under Hard Drives, unplug, and then replug the enclosure. If I do that then the process in the previous paragraph repeats. In Ubuntu the enclosure never shows up at all at the file system level. Below are an excerpt from kern.log and an excerpt from the result of lsusb -v after attaching the enclosure. It appears that Ubuntu at first recongnizes the enclosure and is attempting to attach it, but encounters errors which prevent it from doing so. Unfortunately, I don't know whether any of this info is useful or not. excerpt from kern.log [ 2684.240015] usb 1-2: new high speed USB device using ehci_hcd and address 22 [ 2684.393618] usb 1-2: configuration #1 chosen from 1 choice [ 2684.395399] scsi17 : SCSI emulation for USB Mass Storage devices [ 2684.395570] usb-storage: device found at 22 [ 2684.395572] usb-storage: waiting for device to settle before scanning [ 2689.390412] usb-storage: device scan complete [ 2689.390894] scsi 17:0:0:0: Direct-Access Hitachi HDT721010SLA360 ST6O PQ: 0 ANSI: 4 [ 2689.392237] sd 17:0:0:0: Attached scsi generic sg7 type 0 [ 2689.395269] sd 17:0:0:0: [sde] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 2689.395632] sd 17:0:0:0: [sde] Write Protect is off [ 2689.395636] sd 17:0:0:0: [sde] Mode Sense: 11 00 00 00 [ 2689.395639] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412003] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412009] sde: sde1 sde2 [ 2689.455759] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.455765] sd 17:0:0:0: [sde] Attached SCSI disk [ 2692.620017] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2707.740014] usb 1-2: device descriptor read/64, error -110 [ 2722.970103] usb 1-2: device descriptor read/64, error -110 [ 2723.200027] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2738.320019] usb 1-2: device descriptor read/64, error -110 [ 2753.550024] usb 1-2: device descriptor read/64, error -110 [ 2753.780020] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2758.810147] usb 1-2: device descriptor read/8, error -110 [ 2763.940142] usb 1-2: device descriptor read/8, error -110 [ 2764.170014] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2769.200141] usb 1-2: device descriptor read/8, error -110 [ 2774.330137] usb 1-2: device descriptor read/8, error -110 [ 2774.440069] usb 1-2: USB disconnect, address 22 [ 2774.440503] sd 17:0:0:0: Device offlined - not ready after error recovery [ 2774.590023] usb 1-2: new high speed USB device using ehci_hcd and address 23 [ 2789.710020] usb 1-2: device descriptor read/64, error -110 [ 2804.940020] usb 1-2: device descriptor read/64, error -110 [ 2805.170026] usb 1-2: new high speed USB device using ehci_hcd and address 24 [ 2820.290019] usb 1-2: device descriptor read/64, error -110 [ 2835.520027] usb 1-2: device descriptor read/64, error -110 [ 2835.750018] usb 1-2: new high speed USB device using ehci_hcd and address 25 [ 2840.780085] usb 1-2: device descriptor read/8, error -110 [ 2845.910079] usb 1-2: device descriptor read/8, error -110 [ 2846.140023] usb 1-2: new high speed USB device using ehci_hcd and address 26 [ 2851.170112] usb 1-2: device descriptor read/8, error -110 [ 2856.300077] usb 1-2: device descriptor read/8, error -110 [ 2856.410027] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 2856.730033] usb 3-2: new full speed USB device using uhci_hcd and address 11 [ 2871.850017] usb 3-2: device descriptor read/64, error -110 [ 2887.080014] usb 3-2: device descriptor read/64, error -110 [ 2887.310011] usb 3-2: new full speed USB device using uhci_hcd and address 12 [ 2902.430021] usb 3-2: device descriptor read/64, error -110 [ 2917.660013] usb 3-2: device descriptor read/64, error -110 [ 2917.890016] usb 3-2: new full speed USB device using uhci_hcd and address 13 [ 2922.911623] usb 3-2: device descriptor read/8, error -110 [ 2928.051753] usb 3-2: device descriptor read/8, error -110 [ 2928.280013] usb 3-2: new full speed USB device using uhci_hcd and address 14 [ 2933.301876] usb 3-2: device descriptor read/8, error -110 [ 2938.431993] usb 3-2: device descriptor read/8, error -110 [ 2938.540073] hub 3-0:1.0: unable to enumerate USB device on port 2 excerpt from lsusb -v Bus 001 Device 017: ID 0dc4:0000 Macpower Peripherals, Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0dc4 Macpower Peripherals, Ltd idProduct 0x0000 bcdDevice 0.01 iManufacturer 1 EZ QUEST iProduct 2 USB Mass Storage iSerial 3 220417 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 5 Config0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 4 Interface0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Update: Results using Firewire to connect. Today I recieved a 1394b 9 pin to 1394a 6 pin cable which allowed me to connect the "EZQuest Pro" via Firewire. Everything works. When I use Firewire I can connect whether I'm using Windows 7 or Ubuntu 10.04. I even tried booting my Gigabyte desktop as an OS X 10.6.3 Hackintosh and it worked there as well. (Though if I recall correctly, it also worked when using USB 2.0 and booting OS X on the desktop. Certainly it works with USB 2.0 and my MacBook.) I believe the firmware on the device is at the latest level available, v1.07. I base this on the excerpt below from the OS X System Profiler which shows Firmware Revision: 0x107. Bottom line: It's nice that the enclosure is actually usable when I connect with Firewire. But I am still searching for an answer as to why it does not work correctly when using USB 2.0 in Windows 7 (and Ubuntu ... but really Windows 7 is my biggest concern). OXFORD IDE Device 1: Manufacturer: EZ QUEST Model: 0x0 GUID: 0x1D202E0220417 Maximum Speed: Up to 800 Mb/sec Connection Speed: Up to 400 Mb/sec Sub-units: OXFORD IDE Device 1 Unit: Unit Software Version: 0x10483 Unit Spec ID: 0x609E Firmware Revision: 0x107 Product Revision Level: ST6O Sub-units: OXFORD IDE Device 1 SBP-LUN: Capacity: 1 TB (1,000,204,886,016 bytes) Removable Media: Yes BSD Name: disk3 Partition Map Type: MBR (Master Boot Record) S.M.A.R.T. status: Not Supported

    Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >