Search Results

Search found 102 results on 5 pages for 'xinerama'.

Page 1/5 | 1 2 3 4 5  | Next Page >

• Can't login to Unity 3d after enabling Xinerama for a short moment

  - by Amir Adar

  Today I connected a second monitor to my computer. I set it up using nVidia's control panel, and all was working quite well, so I figured it won't be a problem to try Xinerama, just to see the difference between that and twinview. After enabling Xinerama and restarting the X session, I saw that I was logged into a Unity 2d session. I thought it was a problem with Xinerama, so I switched back to twinview, but it still logged me into Unity 2d. I tried disconnecting the second monitor, no luck: still Unity 2d. I tried changing GPU drivers and installing drivers from a separate ppa, and still I was logged into Unity 2d. Up until this point, I didn't have any problem logging into Unity 3d. It only happened after I tried using Xinerama. I should note that I was doing all this while updates were going on in the background, so it could be something related to that, though I can't imagine what (I tried booting with another kernel, but no luck). So what exactly happened? Did changing the mode to Xinerama triggered some other changes that I'm not aware of? Did these updates cause a certain malfunction in the driver? Is it something else?

  Read the article

• Gnome 3 - Multiple Video Cards - Xinerama -- Forced Fallback Mode

  - by Alvin

  Just installed a 2nd nvidia video card -- previously had gnome 3 working perfectly with 2 monitors on a a single video card using twinview tried a number of things thus far twinview on 1 card + xinerama no xinerama no twinview various manual xorg.conf hacks based on random forums (couple references below) xinerama no twinview with and without Extensions Composite The last one is what I'm using now -- it results in a forced fallback mode with Composite Disable set at the end of xorg.conf via nvidia-settings Section "Extensions" Option "Composite" "Disable" EndSection when I disabled that last snippet it boots to gnome 3 full with the left monitor on a black screen and the middle monitor as primary but non-responsive switching to console mode Ctrl+Alt+F1 and then switching back I get 3 black screens with a mouse that can move around but nothing to interact with issue seems related to OpenGL and the multiple video cards -- I can boot into Unity without issue though my Glx-Dock shows up with the black background as barely shows in the screenshot below indicating the OpenGL is not initiated has anyone had any luck with getting Xinerama to work with Multiple NVidia Video Cards with OpenGL support? Found this in the logs while looking a bit further [ 23.208] (II) NVIDIA(1): Setting mode "nvidia-auto-select+0+0" [ 23.254] (WW) NVIDIA(1): The GPU driving screen 1 is incompatible with the rest of the [ 23.254] (WW) NVIDIA(1): GPUs composing the desktop. OpenGL rendering will be [ 23.254] (WW) NVIDIA(1): disabled on screen 1. [ 23.277] (==) NVIDIA(1): Disabling shared memory pixmaps [ 23.277] (==) NVIDIA(1): Backing store disabled [ 23.277] (==) NVIDIA(1): Silken mouse enabled [ 23.277] (==) NVIDIA(1): DPMS enabled According to this page at the NVidia User Docs http://us.download.nvidia.com/XFree86/Linux-x86/173.14.09/README/chapter-14.html I may be out of luck =( Starting this question with the hopes that others may be able to help debug and perhaps gain answers over time as I really want to get the full gnome 3 back.

  Read the article

• radeon display driver clones monitors while using Xinerama

  - by gregmuellegger

  I'm trying to get my two Radeon HD 4770 cards working with three monitors. Xinerama works so far in the way that I have two fully working monitors were I can move windows from one to the other. My problem now is that my third monitor is a clone of my second monitor (displaying the exact same thing). These monitors are connected to the same graphic card ("Screen Middle" and "Screen Right" in the xorg.conf below). Here is my xorg.conf: Section "ServerLayout" Identifier "ThreeMonitors" Screen "Screen Left" 0 0 Screen "Screen Middle" RightOf "Screen Left" Screen "Screen Right" RightOf "Screen Middle" Option "Xinerama" EndSection Section "Monitor" Identifier "Monitor Left" Option "DPMS" EndSection Section "Monitor" Identifier "Monitor Middle" Option "DPMS" EndSection Section "Monitor" Identifier "Monitor Right" Option "DPMS" EndSection Section "Device" Identifier "Device Left" Driver "radeon" VendorName "ATI Technologies Inc" BoardName "ATI Radeon HD 4770 [RV740]" BusID "PCI:3:0:0" Screen 0 EndSection Section "Screen" Identifier "Screen Left" Device "Device Left" Monitor "Monitor Left" SubSection "Display" Depth 24 EndSubSection EndSection Section "Device" Identifier "Device Middle" Driver "radeon" VendorName "ATI Technologies Inc" BoardName "ATI Radeon HD 4770 [RV740]" BusID "PCI:2:0:0" Screen 0 EndSection Section "Screen" Identifier "Screen Middle" Device "Device Middle" Monitor "Monitor Middle" SubSection "Display" Depth 24 EndSubSection EndSection Section "Device" Identifier "Device Right" Driver "radeon" VendorName "ATI Technologies Inc" BoardName "ATI Radeon HD 4770 [RV740]" BusID "PCI:2:0:1" Screen 1 EndSection Section "Screen" Identifier "Screen Right" Device "Device Right" Monitor "Monitor Right" SubSection "Display" Depth 24 EndSubSection EndSection I'm using a fresh Kubuntu 10.10 installation with propsed-updates enabled since this repo contains a xorg fix for using multiple graphic cards. I hope someone can help me out. Very many thanks!!

  Read the article

• Please Help with ATI Radeon 4250 and Xinerama

  - by Luis Enrique

  I am using ubuntu 11.10 fresh install and I am having problems making the second screen to work, I remember before I was able to do it by extending the desktop to a larger number like 3840 X 1080 but since I am new I completely forgot how to do it, Now I have a philips 230 E monitor full 1920 X 1080 and a Toshiba tv HDMI and I want to activate the second monitor to be able to use Xinerama but I don't know how to go about this, I want to keep the Phillips as a primary monitor since it's the smaller one and use the TV from time to time to play videos movies and presentations. I installed all the additional drivers and don't know what else to do. I would prefer if I can use a list of exact commands to copy and paste onto the terminal since that is all I know how to use LOL . Thank you so much for your help. If you need more details of my mother board or video card or cpu just ask thank you. Luis

  Read the article

• Dual displays not working with Xinerama in Ubuntu 12.04

  - by user68489

  I just upgraded from Ubuntu 10.10 to 12.04. I had been using a display configuration just like the one described at http://bitkickers.blogspot.com/2009/08/rotate-just-one-monitor-with.html without any problems under 10.10. I have an nvidia Quadro FX 380 and have upgraded to the latest drivers (295.49). Everything appears to be fine when the system first boots up. However, after logging in, the left screen goes black, and the right screen displays what should be displayed on the left screen. Logging into Ubuntu 2D somewhat improves things. The left screen correctly displays the left portion of the desktop but the right screen contains a duplicate view of the left screen. Turning off Xinerama and enabling TwinView appears to fix the issues but does not allow the right monitor to be rotated. Since the display problems start to occur only after logging on, I thought it might have to do with carryover user configuration from 10.10 but the problems persist even when logging in as a guest. Clicking on System Settings - Displays results in the error message "Could not get screen information - RANDR extension is not present." Any help would be greatly appreciated.

  Read the article

• Xinerama creates a panning viewport

  - by iblue

  EDIT: I've created a bug report: https://bugs.freedesktop.org/show_bug.cgi?id=48458 My Setup I have 4 monitors, 1920x1080, which are in portrait mode (rotated left). They are connected to two radeon graphic cards. As usual, a picture says more than a thousand words. The problem Everything works fine, when Xinerama is disabled. But when I enable Xinerama, things get weird. When I move the mouse of the screen and return, the screen contents begin to move with the mouse, only on this monitor. It seems like the virtual display size does not match the real screen size, which activates a panning viewport. Any idea how to stop this? The video I created a video to demonstrate the issue: http://www.youtube.com/watch?v=zq_XHji1P24 xorg.conf This is my xorg.conf: Section "ServerLayout" ##################[ Evilness begins here ]############# Option "Xinerama" "on" # <--- Makes it go b0rked! ##################[ End of all evil ]############# Identifier "BOFH Console of Doom" Screen 0 "Screen-0" 0 0 Screen 1 "Screen-1" RightOf "Screen-0" Screen 2 "Screen-2" RightOf "Screen-1" Screen 3 "Screen-3" RightOf "Screen-2" EndSection Section "ServerFlags" Option "RandR" "false" EndSection Section "Module" Load "dbe" Load "dri" Load "extmod" Load "dri2" Load "record" Load "glx" EndSection Section "Monitor" Identifier "Monitor-0" Option "Rotate" "left" EndSection Section "Monitor" Identifier "Monitor-1" Option "Rotate" "left" EndSection Section "Monitor" Identifier "Monitor-2" Option "Rotate" "left" EndSection Section "Monitor" Identifier "Monitor-3" Option "Rotate" "left" EndSection Section "Device" Identifier "Radeon-0-0" Driver "radeon" BusID "PCI:9:0:0" Option "ZaphodHeads" "DVI-0" Screen 0 EndSection Section "Device" Identifier "Radeon-0-1" Driver "radeon" BusID "PCI:9:0:0" Option "ZaphodHeads" "DVI-1" Screen 1 EndSection Section "Device" Identifier "Radeon-1-0" Driver "radeon" BusID "PCI:4:0:0" Option "ZaphodHeads" "DVI-2" Screen 0 EndSection Section "Device" Identifier "Radeon-1-1" Driver "radeon" BusID "PCI:4:0:0" Option "ZaphodHeads" "DVI-3" Screen 1 EndSection Section "Screen" Identifier "Screen-0" Device "Radeon-0-0" Monitor "Monitor-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen-1" Device "Radeon-0-1" Monitor "Monitor-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen-2" Device "Radeon-1-0" Monitor "Monitor-2" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen-3" Device "Radeon-1-1" Monitor "Monitor-3" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

  Read the article

• Enabling hardware acceleration and Xinerama for multi-monitor/multi-GPU in Linux

  - by mynameiscoffey

  My current setup is three monitors connected as follows (monitors listed from left to right): GPU0 (nVidia GTX 280): - Dell 2405FPW (1920x1200) - Dell U2410 (1920x1200) GPU1 (nVidia 210): - Dell 2405FPW (1920x1200) Works like a charm in Windows 7, not so much in Linux. I seem to only have three real options: Run all three monitors as a seperate X screen, I get hardware acceleration but as they are all independent X sessions I cannot move windows between them and can only have firefox open on one at any given time. Run the two on GPU0 in TwinView mode and have GPU1 as a seperate X screen. Same limitation as 1 but at least two monitors work together ok. I did have an issue where occasionally Linux saw both monitors on GPU0 as a single large monitor however. Enable Xinerama and have everything work as I want it to but hardware acceleration is gone and the display is Windows 95 style choppy. My ideal solution would be to have all screens working as they do under Xinerama without the limitation of having hardware acceleration disabled. I don't even care if that means rendering all three on GPU0 and somehow farming out the display of the third monitor to GPU1, whatever works. My question is this: is there any way to accomplish this? I don't feel like my use case is so out there that there shouldn't be at least some form of support (beyond the three limited options presented above), or is my best option going to be to just suck it up and pick up a better card to replace both that can handle three outputs by itself?

  Read the article

• Fix for: Xlib: extension "XINERAMA" missing on display

  - by obeliksz

  I am using Xming 6.9 with putty trying to run libreoffice remotely. It works well, but an error line appears in the terminal from where I launch it: Xlib: extension "XINERAMA" missing on display "localhost:12.0". Looks like it needs this extension but I can't find the necessary dll file (libXinerama-1.dll) for it as it is not included in the package. I ask for a link from where I could download this file (I accept a hit with a lmgtfy if you can do it) or the source code of it and how to complie it on my win7 machine... or just a surface fix could do it also if it is really clean and simple: hide the error line.

  Read the article

• Multiple X screens without Xinerama

  - by Kalle Elmér

  Is there some way to move Windows between separate X screens in Ubuntu 12.04? With 3 monitors on 2 GPUs, using Twinview is not an option. Xinerama allows me to drag windows between all monitors, but it also means that I lose all hardware acceleration. I don't expect to be able to drag windows between the screens and have them occupy two monitors simultaneously, but there must be some way to transfer a program while it is running. At the moment, I don't even know how to select which monitor it will use when launched. Any pointers?

  Read the article

• How to setup Dual Head with "radeon" driver for R770?

  - by user1709408

  I want to make dual head setup without xrandr but with Xinerama. I put "Screen 1" line into xorg.conf, but card still show identical output on DVI-2 and DVI-3 It is important to use xinerama for me (to glue three monitors), that's why i decide not to use ranrd (randr is incompatible with xinerama as i read somewhere) Here is my videocard (HD 4850 X2): lspci | grep R700 03:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI R700 [Radeon HD 4850] 04:00.0 Display controller: Advanced Micro Devices [AMD] nee ATI R700 [Radeon HD 4850] Here is how monitors are connected: grep "DVI" /var/log/Xorg.0.log [ 1210.002] (II) RADEON(0): Output DVI-0 using monitor section Monitor0 [ 1210.048] (II) RADEON(0): Output DVI-1 has no monitor section [ 1210.079] (II) RADEON(0): EDID for output DVI-0 [ 1210.080] (II) RADEON(0): Printing probed modes for output DVI-0 [ 1210.128] (II) RADEON(0): EDID for output DVI-1 [ 1210.128] (II) RADEON(0): Output DVI-0 connected [ 1210.128] (II) RADEON(0): Output DVI-1 disconnected [ 1210.128] (II) RADEON(0): Output DVI-0 using initial mode 1920x1200 [ 1210.160] (II) RADEON(1): Output DVI-2 using monitor section Monitor2 [ 1210.215] (II) RADEON(1): Output DVI-3 has no monitor section [ 1210.246] (II) RADEON(1): EDID for output DVI-2 [ 1210.247] (II) RADEON(1): Printing probed modes for output DVI-2 [ 1210.299] (II) RADEON(1): EDID for output DVI-3 [ 1210.300] (II) RADEON(1): Printing probed modes for output DVI-3 [ 1210.300] (II) RADEON(1): Output DVI-2 connected [ 1210.300] (II) RADEON(1): Output DVI-3 connected [ 1210.300] (II) RADEON(1): Output DVI-2 using initial mode 1920x1200 [ 1210.300] (II) RADEON(1): Output DVI-3 using initial mode 1920x1200 Here is my /etc/X11/xorg.conf Section "ServerFlags" Option "RandR" "0" Option "Xinerama" "1" EndSection Section "ServerLayout" Identifier "Three Head Layout" Screen "MyPrecious0" Screen "MyPrecious2" RightOf "MyPrecious0" Screen "MyPrecious3" LeftOf "MyPrecious0" EndSection Section "Screen" Identifier "MyPrecious0" Monitor "Monitor0" Device "Device300" EndSection Section "Screen" Identifier "MyPrecious2" Monitor "Monitor2" Device "Device400" EndSection Section "Screen" Identifier "MyPrecious3" Monitor "Monitor3" Device "Device401" EndSection Section "Device" Identifier "Device300" BusID "PCI:3:0:0" Screen 0 Driver "radeon" EndSection Section "Device" Identifier "Device400" BusID "PCI:4:0:0" Screen 0 Driver "radeon" EndSection Section "Device" Identifier "Device401" BusID "PCI:4:0:0" Screen 1 Driver "radeon" EndSection Section "Monitor" Identifier "Monitor0" EndSection Section "Monitor" Identifier "Monitor2" EndSection Section "Monitor" Identifier "Monitor3" EndSection I tried to switch to vesa driver (didn't work for me) I tried to add options like Option "ZaphodHeads" "DVI-2" and Option "ZaphodHeads" "DVI-3" into sections "Device 400" and "Device 401" (this didn't help because "ZaphodHeads" option is for ranrd, and randr is disabled by decision) I tried to merge sections "Device 400" and "Device 401" into one section and add Option "ZaphodHeads" "DVI-2,DVI-3" (see comment about randr above) single section setup helps to change log line RADEON(1): Output DVI-3 has no monitor section into RADEON(1): Output DVI-3 using monitor section Monitor3 but nothing was enough to switch from screen cloning to separate screens. This problem (lack of documentation on radeon driver) is similar to these: Radeon display driver clones monitors while using Xinerama (moderators decision to close that problem was wrong) Ubuntu 12.10 multi-monitor setup isn't working The problem is solvable, because this hardware worked as three headed for me earlier with gentoo/xorg-server-1.3 Xorg -configure creates setup for the first monitor on the first GPU Please don't advise to use fglrx/aticonfig/amdcccle (this goes against my religion beliefs)

  Read the article

• Dual nVidia GPUs (3 monitors) not working in 11.10

  - by jasonmclose

  after searching I have not found a solution. I have 2 nvidia quadro 295 cards with 3 monitors but I can not extend twinview across multiple GPUs. I have the most recent nvidia proprietary drivers installed, and they work fine for the single GPU / dual monitors. I tried using xinerama, but without success. I don't mind switching to the nouveau drivers if that would handle my multiple monitors, although I would like to continue to use unity and compiz if i can).

  Read the article

• Is there a simple, safe way to trigger a GPU lockup on a susceptible computer?

  - by Abe

  Answers to my previous question, Ubuntu 12.04 froze, requiring powercycle. What should I look / grep for in the logs?, have led me to suspect that my computer is experiencing an intermittent GPU lockup. It has been happening about once a week, usually when I am using Chrome. Today it happened when I was creating a diagram on lucidchart I have a Dell Optiplex 755 with an ATI Radeon HD 2400 XT and dual monitors running in Xinerama mode. I am using 12.04 with the proprietary ATI driver installed. When the computer locks-up, I can still ssh in. And I would like to follow the instructions on reporting this provided at https://wiki.ubuntu.com/X/Troubleshooting/Freeze Is there a (safe) way to cause a GPU lockup so that I can go ahead and file a bug, rather than waiting until it happens again?

  Read the article

• Xinerama 3 displays can't have main display in the middle

  - by mononym

  I have 3 monitors running on 2 cards, they are all working as 3 seperate displays, however, if i move the main display from the left (0,0) i cannot drag to the left window as the mouse goes crazy and crashes my system (i have to restart x) I would much prefer my main display to be in the centre. Any help appreciated

  Read the article

• Tri-head linux system with Xmonad: is it possible to have HW acceleration

  - by progo

  What means there exists to have three monitors, all controlled by Xmonad and have hardware 3D acceleration as well? I had the pleasure of using three monitors earlier this year, and while Xmonad and Xinerama handle three monitors easily, I had to throw in an extra display driver, and also let go of Nvidia's own TwinView (which is a hack on Xinerama). This left me with no HW acceleration and some flickering as double buffering wouldn't work with certain applications. However, the three monitors handle so beautifully that I had hard time coming back to two. I understand the easiest way to achieve HW-accelerated tri-head combo is to split into two Xorgs. I wouldn't be able to switch windows between the Xorgs, so I'm not really into this solution. What's more, having a cheap and old PCI card along with even slightly better PCIe seemed to slow things down. Even if I occasionally disabled the third monitor from Xorg configure, I couldn't get HW acceleration to work. Only after I physically disconnected the old PCI card, I could get the games back in business. Would a Matrox Dual/Tri-head2go and a powerful Nvidia GPU do the trick? I understand Xmonad can be configured to "believe" that a "single" (as Dualhead2Go will merge) 3360x1050 display is actually two different ones? So that Xmonad's Mod-w and Mod-e would work properly there.

  Read the article

• 3 Monitors, Ubuntu 12.04, Gnome 3, 2 nvidia cards, WITH xrandr or xinerama?

  - by Josh

  Ok. I have been banging my head against the wall for over a week now trying to get 3 monitors to work. I have: 1 - Nvidia 8600 GT 512MB PCIEx16 1 - Nvidia GT 240 1GB PCIEx16 They are not running in SLI (obviously). I have tried to use everything from tutorials to a few templates, all the way up to nvidia-settings, etc etc etc.. From what I hear, Xinerama doesnt like gnome 3 because of the compositing, although I have read a lot about using Xrandr instead, and getting the compositing working, but alas, I cannot. It always either crashes X and I have to replace the xorg.conf with my backup, or it defaults to the gnome-classic desktop, and on top of that, when it does default, it keeps adding more and more panels. Basically, I want to be able to use all 3 monitors (yes, just like in windows) to drag and drop from different windows. I have xorg-edit, but I am still not too sure on how to set this up? Is there any way to: A Get compositing working with 3 monitors, 2 nvidia cards, xinerama, and gnome 3? or BUse twinview with 3 monitors (I have heard it can be done by manually editing xorg.conf) or CSet up Xrandr to draw all 3 monitors with compositing. or DUse separate X for each monitor, and be able to use gnome with compositing, as well as drag between all 3 or EANYTHING. lol. I just want this to work. Any help you can provide would be greatly appreciated. BTW, I am running an ubuntu mini install with gnome. Everything works great but this. I can run it fine with 2 monitors and compositing, but not with 3. Also, what is the best GUI tool for editing xorg.conf? Im not finding anything that is up to date at all, and also is understandable by humans. haha. Im actually an engineer by trade, and have been working with computers a LONG time, but this xorg.conf stuff is really confusing the crap out of me. lol Thanks!

  Read the article

• Dual Monitor/Xinerama not working; cannot even detect on-board graphic card

  - by Steven H

  I have Kubuntu 12.04 and two identical VGA monitors. One I plugged via DVI-VGA adapter into the DVI port of my discrete AMD Radeon HD 6670, the other into the VGA port of my on-board graphic card (Radeon HD 6410D). After installing Kubuntu I got a black screen, so I booted with nomodeset and installed AMD's catalyst drivers but only the monitor plugged into the discrete graphic card worked. Using lspci I saw that the on-board graphics was not listed. Then I found in the BIOS settings the options "Surround View" and "Onboard Dual Link DVI" both disabled. After enabling both, the on-board graphics card shows up in lspci but in amdcccle, it only shows as [Uknown display]Uknown adapter. When I try to enable xinerama, I get a black screen after rebooting on both monitors. I tried several options and hints from the web but nothing worked so far. I also reinstalled the AMD drivers several times. What should I do?

  Read the article

• Triple (3) Monitors under Linux

  - by widgisoft

  I have a 3 monitor setup (each 1680x1050) via an Nvidia NVS440 (2 GPUs, 2 outputs per GPU totalling 4 outputs); this works fine under Windows XP,7 but caused considerable headaches under Linux (Ubuntu 9.04). I had previously used an XFX 9600GT and the onboard XFX 9300GS to produce the same result but the card was noisy and power hungry and I was hoping that there was some magical switch in the NVS4400 that got rid of this annoying problem - turns out the NVS440 is just 2 cards on one physical PCB :-p (I searched the net high and low for people using this card under Linux but found nothing, if anything the card uses less power and is fan less so I was to benefit from it either way) Anyway, using either set up there were 5 solutions available: Have 3 separate X instances, all un joined Have 3 separate X instances, adjoined by Xinerama Have 2 separate X instances - One using twin-view, both adjoined by Xinerama Have 2 separate X instances - One using twin-view but no Xinerama Have a single Twin-view setup and leave the 3rd screen unplugged :-p The 4rd option, using 2 separate X instances and twinview (but no xinerama) was the best balance in terms of performance and usability but caused 2 really annoying issues You couldn't control (without altering the shortcuts) which screen an application opened onto - and once it was opened you couldn't move it to another screen without opening up terminal and forcing it to move Nvidia's overriding or falsifying of Xinerama breaks and the 2 screens joined by Twin view behave like a single huge screen causing popups to open in the middle of both screens and maximising of windows stretches to the width of the first 2 screens Firefox can only run one instance as the same user so having multiple firefox windows requires at least 2 users The second option "feels" like the right option, but OpenGL is basically disabled and playing any sort of game or even running anything graphical causes a huge performance drop and instability - even trying to run a basic emulator for gba or gens just causes the system to fall over. It works just enough to stare at your desktop and do nothing but as soon as you start doing some work - opening windows, dragging things around - running multiple copies of firefox it just really feels slow. The last open, only going dual screen works perfectly and everything performs as required, full GPU acceleration - two logical screen spaces - perfect, just make it work across GPUs like windows! :-p Anyway, I know RandR was supposed to pick up the slack when it would introduced GPU objects of sorts to allow multiple GPUs to be stitched together to create one huge desktop at a much deeper layer than Xinerama. I was wondering if this has now been fixed (I noticed X server 1.7 is out) and whether anyone has got it running successfully? Again, my requirements are: One huge desktop to drag any window across Maximising of windows to each screen (as XP does) Running fullscreen apps on the primary screen and disabling the mouse from moving onto the others or on all 3 stretched Finally as a side note; I am aware of the Matrox triple (and dual) head splitter but even the price they go for on eBay is more than I can afford atm, my argument: I shouldn't have to buy extra hardware to get something to work on Linux when it's something that's existed in the windows world for a long time (can you tell I don't get on with X :-p); If I had the cash I'd have bought the latest version of this box already (the new version finally supports large resolutions as the displays I have 1680x1050 each).

  Read the article

• Dual monitor display 12.04?

  - by MrMonty

  I have 2 beautiful 27" asus monitors. I started trying out Ubuntu 12.04 and now only one works and thats vga .. Any help here cause I'm stumped. I have a bfg tech nivida Geforce 8800 gt 512mb and I'm trying to fix this. Getting this error Wen i try to configure the xorg file Failed to set MetaMode (1) 'DFP-0: 1280x1024 @1280x1024 +0+0, DFP-1: 1280x1024 @1280x1024 +1280+0' (Mode 2560x1024, id: 50) on X screen 0. ........................................................................................... This is the xorg.conf ....................................................... nvidia-settings: X configuration file generated by nvidia-settings nvidia-settings: version 295.33 (buildd@allspice) Fri Mar 30 15:25:24 UTC 2012 Section "ServerLayout" Removed Option "Xinerama" "1" Removed Option "Xinerama" "0" Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputClass" Identifier "Mouse Remap" MatchProduct "Saitek Cyborg R.A.T.7 Mouse" MatchDevicePath "/dev/input/event*" Option "ButtonMapping" "1 2 3 4 5 6 7 8 9 0 0 0 0 0 0" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" BusID "PCI:1:0:0" Screen 1 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "TwinViewXineramaInfoOrder" "DFP-1" Option "metamodes" "DFP-1: 1280x1024 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Removed Option "TwinView" "0" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" Removed Option "TwinView" "1" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0" Removed Option "TwinView" "0" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-0" Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0; DFP-1: 1280x1024_60 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Disable" EndSection FILE ^^^^

  Read the article

• how to setup duel monitors an xorg.conf

  - by MrMonty

  # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 295.33 (buildd@allspice) Fri Mar 30 15:25:24 UTC 2012 Section "ServerLayout" # Removed Option "Xinerama" "1" # Removed Option "Xinerama" "0" # Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" BusID "PCI:1:0:0" Screen 1 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "TwinViewXineramaInfoOrder" "DFP-1" Option "metamodes" "DFP-1: 1280x1024 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" # Removed Option "TwinView" "1" # Removed Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-0" Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0; DFP-1: 1280x1024_60 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Disable" EndSection thats my file!

  Read the article

• Triple monitor setup in linux

  - by Brendan Abel

  I'm hoping there are some xorg gurus out there. I'm trying to get a three monitor setup working in linux. I have 2 lcd monitors and a tv, all different resolutions. I'm using 2 video cards; a 9800 GTX and 7900Gt. I've seen a lot of different posts about people trying to make this work, and in every case, they either gave up, or Xinerama magically solved all their problems. Basically, my main problem is that I cannot get Xinerama to work. Every time I turn it on in the options, my machine gets stuck in a neverending boot cycle. If I disable Xinerama, I just have three Xorg screens, but I can't drag windows from one to the other. I can get the 2 lcds on Twinview, and the tv on a separate Xorg screen no problem. But I don't really like this solution. I'd rather have them all on separate screens and stitch them together with Xinerama. Has anyone done this? Here's my xorg.conf for reference. p.s. This took me all of 30 seconds to set up in Windows XP! p.s.s. I've seen somewhere that maybe randr can solve my problems? But I'm not quite sure how? Section "Monitor" Identifier "Main1" VendorName "Acer" ModelName "H233H" HorizSync 40-70 VertRefresh 60 Option "dpms" EndSection #Section "Monitor" # Identifier "Main2" # VendorName "Acer" # ModelName "AL2216W" # HorizSync 40-70 # VertRefresh 60 # Option "dpms" #EndSection Section "Monitor" Identifier "Projector" VendorName "BenQ" ModelName "W500" HorizSync 44.955-45 VertRefresh 59.94-60 Option "dpms" EndSection Section "Device" Identifier "Card1" Driver "nvidia" VendorName "nvidia" BusID "PCI:5:0:0" BoardName "nVidia Corporation G92 [GeForce 9800 GTX+]" Option "ConnectedMonitor" "DFP,DFP" Option "NvAGP" "0" Option "NoLogo" "True" #Option "TVStandard" "HD720p" EndSection Section "Device" Identifier "Card2" Driver "nvidia" VendorName "nvidia" BusID "PCI:4:0:0" BoardName "nVidia Corporation G71 [GeForce 7900 GT/GTO]" Option "NvAGP" "0" Option "NoLogo" "True" Option "TVStandard" "HD720p" EndSection Section "Module" Load "glx" EndSection Section "Screen" Identifier "ScreenMain-0" Device "Card1-0" Monitor "Main1" DefaultDepth 24 Option "Twinview" Option "TwinViewOrientation" "RightOf" Option "MetaModes" "DFP-0: 1920x1080; DFP-1: 1680x1050" Option "HorizSync" "DFP-0: 40-70; DFP-1: 40-70" Option "VertRefresh" "DFP-0: 60; DFP-1: 60" #SubSection "Display" # Depth 24 # Virtual 4880 1080 #EndSubSection EndSection Section "Screen" Identifier "ScreenProjector" Device "Card2" Monitor "Projector" DefaultDepth 24 Option "MetaModes" "TV-0: 1280x720" Option "HorizSync" "TV-0: 44.955-45" Option "VertRefresh" "TV-0: 59.94-60" EndSection Section "ServerLayout" Identifier "BothTwinView" Screen "ScreenMain-0" Screen "ScreenProjector" LeftOf "ScreenMain-0" #Option "Xinerama" "on" # most important option let you window expand to three monitors EndSection

  Read the article

• Triple monitor setup in linux

  - by Brendan Abel

  I'm hoping there are some xorg gurus out there. I'm trying to get a three monitor setup working in linux. I have 2 lcd monitors and a tv, all different resolutions. I'm using 2 video cards; a 9800 GTX and 7900Gt. I've seen a lot of different posts about people trying to make this work, and in every case, they either gave up, or Xinerama magically solved all their problems. Basically, my main problem is that I cannot get Xinerama to work. Every time I turn it on in the options, my machine gets stuck in a neverending boot cycle. If I disable Xinerama, I just have three Xorg screens, but I can't drag windows from one to the other. I can get the 2 lcds on Twinview, and the tv on a separate Xorg screen no problem. But I don't really like this solution. I'd rather have them all on separate screens and stitch them together with Xinerama. Has anyone done this? Here's my xorg.conf for reference. p.s. This took me all of 30 seconds to set up in Windows XP! p.s.s. I've seen somewhere that maybe randr can solve my problems? But I'm not quite sure how? Section "Monitor" Identifier "Main1" VendorName "Acer" ModelName "H233H" HorizSync 40-70 VertRefresh 60 Option "dpms" EndSection #Section "Monitor" # Identifier "Main2" # VendorName "Acer" # ModelName "AL2216W" # HorizSync 40-70 # VertRefresh 60 # Option "dpms" #EndSection Section "Monitor" Identifier "Projector" VendorName "BenQ" ModelName "W500" HorizSync 44.955-45 VertRefresh 59.94-60 Option "dpms" EndSection Section "Device" Identifier "Card1" Driver "nvidia" VendorName "nvidia" BusID "PCI:5:0:0" BoardName "nVidia Corporation G92 [GeForce 9800 GTX+]" Option "ConnectedMonitor" "DFP,DFP" Option "NvAGP" "0" Option "NoLogo" "True" #Option "TVStandard" "HD720p" EndSection Section "Device" Identifier "Card2" Driver "nvidia" VendorName "nvidia" BusID "PCI:4:0:0" BoardName "nVidia Corporation G71 [GeForce 7900 GT/GTO]" Option "NvAGP" "0" Option "NoLogo" "True" Option "TVStandard" "HD720p" EndSection Section "Module" Load "glx" EndSection Section "Screen" Identifier "ScreenMain-0" Device "Card1-0" Monitor "Main1" DefaultDepth 24 Option "Twinview" Option "TwinViewOrientation" "RightOf" Option "MetaModes" "DFP-0: 1920x1080; DFP-1: 1680x1050" Option "HorizSync" "DFP-0: 40-70; DFP-1: 40-70" Option "VertRefresh" "DFP-0: 60; DFP-1: 60" #SubSection "Display" # Depth 24 # Virtual 4880 1080 #EndSubSection EndSection Section "Screen" Identifier "ScreenProjector" Device "Card2" Monitor "Projector" DefaultDepth 24 Option "MetaModes" "TV-0: 1280x720" Option "HorizSync" "TV-0: 44.955-45" Option "VertRefresh" "TV-0: 59.94-60" EndSection Section "ServerLayout" Identifier "BothTwinView" Screen "ScreenMain-0" Screen "ScreenProjector" LeftOf "ScreenMain-0" #Option "Xinerama" "on" # most important option let you window expand to three monitors EndSection

  Read the article

• Windows expand over 2 monitors in quad-monitor setup

  - by Martin

  i just installed ubuntu 11.10 with my previous hardware setup: 4 monitors and 2 identical nvidia graphic cards. draging windows around all 4 monitors works nice, but when i maximize a window it expand always over 2 screens. (2x twinview). i had an workaround for this in 11.04 but cant remember what it was... may one of you guys have quad monitors up and running with window maximizing on only one screen my xorg.conf looks like this: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 280.13 (buildd@allspice) Thu Aug 11 20:54:45 UTC 2011 # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 280.13 ([email protected]) Wed Jul 27 17:15:58 PDT 2011 Section "ServerLayout" # Removed Option "Xinerama" "1" # Removed Option "Xinerama" "0" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" 0 1080 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "1" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Samsung SMB2220N" HorizSync 31.0 - 80.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Unknown" ModelName "Samsung SMB2220N" HorizSync 31.0 - 80.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 550 Ti" BusID "PCI:2:0:0" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 550 Ti" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "TwinView" "True" # Removed Option "MetaModes" "nvidia-auto-select, nvidia-auto-select" # Removed Option "metamodes" "CRT-0: nvidia-auto-select 1920x1080 +0+0, CRT-1: nvidia-auto-select 1920x1080 +1920+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "CRT-0" Option "metamodes" "CRT-0: nvidia-auto-select +0+0, CRT-1: nvidia-auto-select +1920+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" # Removed Option "TwinView" "True" # Removed Option "MetaModes" "nvidia-auto-select, nvidia-auto-select" # Removed Option "metamodes" "CRT-0: nvidia-auto-select 1920x1080 +0+0, CRT-1: nvidia-auto-select 1920x1080 +1920+0" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "CRT-0" Option "metamodes" "CRT-0: nvidia-auto-select +0+0, CRT-1: nvidia-auto-select +1920+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Disable" EndSection

  Read the article

• Ubuntu Lucid: Erratic screen behaviour after boot

  - by fgysin

  In short: about 50% of the time I have a screwed up monitor setup after reboot. About 50% it is totally correct. Now the longer version: I updated my machine from 9.04 to 10.04 (via 9.10). At first I run into some monitor problems (I have a 3-monitor setup) because of the known bug in the new xserver driver for xinerama. This messes up behaviour if the mouse goes either left or above the screen number 0, i.e. I had to make my left-most monitor screen 0. Everything worked out fine finally, I got my 3-monitor setup back with xinerama enabled to get one big desktop streched over 3 screens. Now the fun part: Every time I start up my machine only one of the 3 monitors gets a signal and is woken up: it only recognizes the left-most monitor (screen 0) and crams all the desktop stuff into this one screen. If I go into nvidia settings I only see one physical device although all 3 are connected and have power. When I look into the xorg.conf I can still see my old setup with 3 devices, 3 screens, xinerama active etc... But I was totally unable to get 3 montitors to work. (I tried unplugging monitors, reconfiguring whole nvidia setup, ...) But it gets even better: When I restart my machine (i.e. choose the restart option from the Ubuntu menu) it shuts down and tries to restart. The restart then gets stuck after showing the Ubuntu splash screen with the 'loading bar' (the moving dots thingy) and I am forced to kill the machine by cutting power. But after the power cut the machine boots up normally and suddenly I get my 3 monitor setup back up working. That is until the next time I shut down and start up, where it all starts over again and I only have one monitor... (see above) I really have a hard time seeing where the error is. It must be that the restart boot somehow differs from the 'normal' boot. But the fact that it gets stuck and I need to cut power which then basically triggers a 'normal' boot does not really support this theory... My setup (please tell me if you need further info): 3 monitors as 3 screens as one desktop (with xinerama) 2 nvidia cards where screen 0 and 1 are on card 0 and screen 2 is on card 1 Ubuntu 10.04 Lucid Lynx (updated from 9.10, 9.04, ....) I would appreciate every idea on the subject, at the moment I really don't have any clue what to do...

  Read the article

• Ubuntu Lucid: Erratic screen behaviour after boot

  - by fgysin

  In short: about 50% of the time I have a screwed up monitor setup after reboot. About 50% it is totally correct. Now the longer version: I updated my machine from 9.04 to 10.04 (via 9.10). At first I run into some monitor problems (I have a 3-monitor setup) because of the known bug in the new xserver driver for xinerama. This messes up behaviour if the mouse goes either left or above the screen number 0, i.e. I had to make my left-most monitor screen 0. Everything worked out fine finally, I got my 3-monitor setup back with xinerama enabled to get one big desktop streched over 3 screens. Now the fun part: Every time I start up my machine only one of the 3 monitors gets a signal and is woken up: it only recognizes the left-most monitor (screen 0) and crams all the desktop stuff into this one screen. If I go into nvidia settings I only see one physical device although all 3 are connected and have power. When I look into the xorg.conf I can still see my old setup with 3 devices, 3 screens, xinerama active etc... But I was totally unable to get 3 montitors to work. (I tried unplugging monitors, reconfiguring whole nvidia setup, ...) But it gets even better: When I restart my machine (i.e. choose the restart option from the Ubuntu menu) it shuts down and tries to restart. The restart then gets stuck after showing the Ubuntu splash screen with the 'loading bar' (the moving dots thingy) and I am forced to kill the machine by cutting power. But after the power cut the machine boots up normally and suddenly I get my 3 monitor setup back up working. That is until the next time I shut down and start up, where it all starts over again and I only have one monitor... (see above) I really have a hard time seeing where the error is. It must be that the restart boot somehow differs from the 'normal' boot. But the fact that it gets stuck and I need to cut power which then basically triggers a 'normal' boot does not really support this theory... My setup (please tell me if you need further info): 3 monitors as 3 screens as one desktop (with xinerama) 2 nvidia cards where screen 0 and 1 are on card 0 and screen 2 is on card 1 Ubuntu 10.04 Lucid Lynx (updated from 9.10, 9.04, ....) I would appreciate every idea on the subject, at the moment I really don't have any clue what to do...

  Read the article

• Dual Screen with 12.04 ATI randr extension is not present

  - by Trevor Pearson

  Here's my problem I have two screens. One is a 22"led monitor and the other is 42 inch led tv. In windows 7 I run xbmc on the second monitor. I'm trying to mimic the same function in setting xbmc to display on the tv only. So I installed the latest x64 linux drivers from ATI. I configured (using the catalyst control panel) using single display (multi desktop) I then got a white screen with black x so I enable xinerama. with xinerama enable I got the displays to work correctly, however I received an error when I tried to enter display settings to change the launcher location. the error message was " "randr extension not present =" So I tried to install libxandr2 using terimal but here's what I get trev@Lrig:~$ sudo get-apt install libxander2 [sudo] password for trev: sudo: get-apt: command not found I'm at a loss now because I can't find a solution for the xandr error message. I'f my specs are important amd athx2 6400+ ghz 8 gigs ram radeon hd6950

  Read the article

1 2 3 4 5  | Next Page >